dt-bindings: extcon: convert extcon-usb-gpio.txt to yaml format
Frank Li
maintainerPATCH 1/1 dt-bindings: extcon: convert extcon-usb-gpio.txt to yaml format
Convert binding doc extcon-usb-gpio.txt to yaml format to fix below warning:arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-ep1.dtb: /extcon-usb0:
failed to match any schema with compatible: ['linux,extcon-usb-gpio']
Additional change:
- rename id-gpio to id-gpios
- rename vbus-gpio to vbus-gpios
--- .../bindings/extcon/extcon-usb-gpio.txt | 21 ---------- .../extcon/linux,extcon-usb-gpio.yaml | 38 +++++++++++++++++++ 2 files changed, 38 insertions(+), 21 deletions(-) delete mode 100644 Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt create mode 100644 Documentation/devicetree/bindings/extcon/linux,extcon-usb-gpio.yaml
Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt deleted +0 -21
@@ -1,21 +0,0 @@ -USB GPIO Extcon device - -This is a virtual device used to generate USB cable states from the USB ID pin -connected to a GPIO pin. - -Required properties: -- compatible: Should be "linux,extcon-usb-gpio" - -Either one of id-gpio or vbus-gpio must be present. Both can be present as well. -- id-gpio: gpio for USB ID pin. See gpio binding. -- vbus-gpio: gpio for USB VBUS pin. - -Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below: - extcon_usb1 { - compatible = "linux,extcon-usb-gpio"; - id-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>; - } - - &omap_dwc3_1 { - extcon = <&extcon_usb1>; - };
Documentation/devicetree/bindings/extcon/linux,extcon-usb-gpio.yaml new file +38 -0
@@ -0,0 +1,38 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/extcon/linux,extcon-usb-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: USB GPIO Extcon device + +maintainers: + - Frank Li <[email protected]> + +description: + This is a virtual device used to generate USB cable states from the USB ID pin + connected to a GPIO pin. + +properties: + compatible: + const: linux,extcon-usb-gpio + + id-gpios: + description: gpio for USB ID pin. See gpio binding. + vbus-gpios: + description: gpio for USB VBUS pin. + +required: + - compatible + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + extcon_usb1 { + compatible = "linux,extcon-usb-gpio"; + id-gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>; + }; +
Signature · 1 line
2.34.1
Quoted 9 lines · Frank Li
Convert binding doc extcon-usb-gpio.txt to yaml format to fix below warning:
arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-ep1.dtb: /extcon-usb0:
failed to match any schema with compatible: ['linux,extcon-usb-gpio']Additional change:
- rename id-gpio to id-gpios
- rename vbus-gpio to vbus-gpios
Quoted 8 lines
Signed-off-by Frank Li <[email protected]>--- .../bindings/extcon/extcon-usb-gpio.txt | 21 ---------- .../extcon/linux,extcon-usb-gpio.yaml | 38 +++++++++++++++++++ 2 files changed, 38 insertions(+), 21 deletions(-) delete mode 100644 Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt create mode 100644 Documentation/devicetree/bindings/extcon/linux,extcon-usb-gpio.yaml
Chanwoo Choi
Applied24. 8. 13. 05:17에 Frank Li 이(가) 쓴 글:
Quoted 78 lines
Convert binding doc extcon-usb-gpio.txt to yaml format to fix below warning:
arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-ep1.dtb: /extcon-usb0:
failed to match any schema with compatible: ['linux,extcon-usb-gpio']Additional change:
- rename id-gpio to id-gpios
- rename vbus-gpio to vbus-gpiosSigned-off-by Frank Li <[email protected]>--- .../bindings/extcon/extcon-usb-gpio.txt | 21 ---------- .../extcon/linux,extcon-usb-gpio.yaml | 38 +++++++++++++++++++ 2 files changed, 38 insertions(+), 21 deletions(-) delete mode 100644 Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt create mode 100644 Documentation/devicetree/bindings/extcon/linux,extcon-usb-gpio.yamlDocumentation/devicetree/bindings/extcon/extcon-usb-gpio.txt deleted +0
-21@@ -1,21 +0,0 @@ -USB GPIO Extcon device - -This is a virtual device used to generate USB cable states from the USB ID pin -connected to a GPIO pin. - -Required properties: -- compatible: Should be "linux,extcon-usb-gpio" - -Either one of id-gpio or vbus-gpio must be present. Both can be present as well. -- id-gpio: gpio for USB ID pin. See gpio binding. -- vbus-gpio: gpio for USB VBUS pin. - -Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below: - extcon_usb1 { - compatible = "linux,extcon-usb-gpio"; - id-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>; - } - - &omap_dwc3_1 { - extcon = <&extcon_usb1>; - };Documentation/devicetree/bindings/extcon/linux,extcon-usb-gpio.yaml new file +28
-0@@ -0,0 +1,38 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/extcon/linux,extcon-usb-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: USB GPIO Extcon device + +maintainers: + - Frank Li <[email protected]> + +description: + This is a virtual device used to generate USB cable states from the USB ID pin + connected to a GPIO pin. + +properties: + compatible: + const: linux,extcon-usb-gpio + + id-gpios: + description: gpio for USB ID pin. See gpio binding. + vbus-gpios: + description: gpio for USB VBUS pin. + +required: + - compatible + +additionalProperties: false
Documentation/devicetree/bindings/extcon/linux,extcon-usb-gpio.yaml line 38
Quoted 10 lines
Documentation/devicetree/bindings/extcon/linux,extcon-usb-gpio.yaml new file +10
-0+ +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + extcon_usb1 { + compatible = "linux,extcon-usb-gpio"; + id-gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>; + }; +
Applied it. Thanks.
Signature · 3 lines
Best Regards, Samsung Electronics Chanwoo Choi