Skip to contentSkip to conversation

arm64: dts: imx8mm: Update Data Modul i.MX8M Mini eDM SBC DT to rev.A01

PATCH Applied Marek Vasut 2 participants 2 messages Aug 18, 2024 – Aug 31, 2024

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm64: dts: imx8mm: Update Data Modul i.MX8M Mini eDM SBC DT to rev.A01

Update the DT to match newest Data Modul i.MX8M Mini eDM SBC rev.A01 board which implements PHY changes. Keep some of the rev.900 PHY node in the DT so that a DTO can be used to support rev.900 boards easily.

---
Cc: Conor Dooley <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Pengutronix Kernel Team <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: Sascha Hauer <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]

---
 .../freescale/imx8mm-data-modul-edm-sbc.dts   | 19 +++++++++++++++++--
 1 file changed, 17 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts +17 -2
index b1f2beb40a98f..472c584fb3bd2 100644
@@ -168,7 +168,7 @@ &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec1>;
 	phy-mode = "rgmii-id";
-	phy-handle = <&fec1_phy>;
+	phy-handle = <&fec1_phy_bcm>;
 	phy-supply = <&buck4_reg>;
 	fsl,magic-packet;
 	status = "okay";
@@ -178,7 +178,7 @@ mdio {
 		#size-cells = <0>;
 
 		/* Atheros AR8031 PHY */
-		fec1_phy: ethernet-phy@0 {
+		fec1_phy_ath: ethernet-phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
 			/*
@@ -191,6 +191,7 @@ fec1_phy: ethernet-phy@0 {
 			reset-deassert-us = <10000>;
 			qca,keep-pll-enabled;
 			vddio-supply = <&vddio>;
+			status = "disabled";
 
 			vddio: vddio-regulator {
 				regulator-name = "VDDIO";
@@ -202,6 +203,20 @@ vddh: vddh-regulator {
 				regulator-name = "VDDH";
 			};
 		};
+
+		/* Broadcom BCM54213PE PHY */
+		fec1_phy_bcm: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			/*
+			 * Dedicated ENET_INT# and ENET_WOL# signals are
+			 * unused, the PHY does not provide cable detect
+			 * interrupt.
+			 */
+			reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+		};
 	};
 };
 
Signature · 1 line
2.43.0
Applied
#1 lore raw
Quoted 5 lines · Marek Vasut

Update the DT to match newest Data Modul i.MX8M Mini eDM SBC rev.A01 board which implements PHY changes. Keep some of the rev.900 PHY node in the DT so that a DTO can be used to support rev.900 boards easily.

Applied, thanks!