Skip to contentSkip to conversation

Add and enable mcore support

PATCH Applied Yashwanth Varakala 2 participants 4 messages Aug 20, 2024 – Aug 23, 2024 Arm i.MX and Layerscape

lore
Share & tools
lore
#0 lore raw

cover Add and enable mcore support

Added m7 core support in uboot for imx8mp by adding the boot variable prepare_mcore and enabled bootaux in defconfig.

Regards,
yashwanth.

Yashwanth Varakala (2):
board: phytec: phycore_imx8mp: Add mcore support
configs: phycore-imx8mp_defconfig: Enabled bootaux command

 board/phytec/phycore_imx8mp/phycore_imx8mp.env | 5 +++--
 configs/phycore-imx8mp_defconfig               | 1 +
 2 files changed, 4 insertions(+), 2 deletions(-)
Signature · 1 line
2.34.1
#1 lore raw

PATCH 1/2 board: phytec: phycore_imx8mp: Add mcore support

Added m7 core support in uboot for imx8mp by adding the boot variable prepare_mcore.

Based on commit 0ed32cc8568a ("LF-6555 imx8m[m/n/p/q]_evk: add bootargs to support mcore")

---
 board/phytec/phycore_imx8mp/phycore_imx8mp.env | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
board/phytec/phycore_imx8mp/phycore_imx8mp.env +3 -2
index f8f878e8f3a..889464e933f 100644
@@ -30,7 +30,7 @@ ip_dyn=yes
 loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr_r} ${fdtfile}
 loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}
 mmcargs=
-	setenv bootargs console=${console}
+	setenv bootargs ${mcore_clk} console=${console}
 	root=/dev/mmcblk${mmcdev}p${mmcroot} ${raucargs} rootwait rw
 mmcautodetect=yes
 mmcboot=
@@ -51,7 +51,7 @@ mmcdev=CONFIG_SYS_MMC_ENV_DEV
 mmcpart=1
 mmcroot=2
 netargs=
-	setenv bootargs console=${console} root=/dev/nfs ip=dhcp
+	setenv bootargs ${mcore_clk} console=${console} root=/dev/nfs ip=dhcp
 	nfsroot=${serverip}:${nfsroot},v3,tcp
 netboot=
 	echo Booting from net ...;
@@ -74,4 +74,5 @@ netboot=
 		echo WARN: Cannot load the DT;
 	fi;
 nfsroot=/srv/nfs
+prepare_mcore=setenv mcore_clk clk-imx8mp.mcore_booted
 sd_dev=1
Signature · 1 line
2.34.1
#2 lore raw

PATCH 2/2 configs: phycore-imx8mp_defconfig: Enabled bootaux command

In reply to Yashwanth Varakala

To start the mcore binary from u-boot, bootaux command is needed.

---
 configs/phycore-imx8mp_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/phycore-imx8mp_defconfig +1 -0
index 63f8a80ba99..6b0ffecf9a7 100644
@@ -24,6 +24,7 @@ CONFIG_SPL_BSS_START_ADDR=0x98fc00
 CONFIG_SPL_BSS_MAX_SIZE=0x400
 CONFIG_SPL=y
 CONFIG_ENV_OFFSET_REDUND=0x3e0000
+CONFIG_IMX_BOOTAUX=y
 CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
 CONFIG_SYS_LOAD_ADDR=0x40480000
 CONFIG_FIT=y
Signature · 1 line
2.34.1
reviewer Applied
#3 lore raw
In reply to Yashwanth Varakala
Quoted 11 lines · Yashwanth Varakala

Added m7 core support in uboot for imx8mp by adding the boot variable prepare_mcore and enabled bootaux in defconfig.

Regards,
yashwanth.

Yashwanth Varakala (2):
board: phytec: phycore_imx8mp: Add mcore support
configs: phycore-imx8mp_defconfig: Enabled bootaux command

Applied all, thanks.