hwmon: (sht4x): add heater support
Subsystems (2)
PATCH 1/1 hwmon: (sht4x): add heater support
Add support for manipulating the internal heater of sht4x devices.
The heater can operate at three heating levels (20, 110 or 200 milliwatts). Also, two heating durations may be selected (0.1 or 1s). Once the heating time elapses the heater is automatically switched off.
--- Documentation/hwmon/sht4x.rst | 10 +++ drivers/hwmon/sht4x.c | 137 +++++++++++++++++++++++++++++++++- 2 files changed, 146 insertions(+), 1 deletion(-)
Documentation/hwmon/sht4x.rst +10 -0
@@ -42,4 +42,14 @@ humidity1_input Measured humidity in %H update_interval The minimum interval for polling the sensor, in milliseconds. Writable. Must be at least 2000. +heater_power The requested heater power, in milliwatts. + Available values: 20, 110, 200 (default: 200). +heater_time The requested operating time of the heater, + in milliseconds. + Available values: 100, 1000 (default 1000). +heater_enable Enable the heater with the selected power + and for the selected time. Write-only. + + - 0: turn off + - 1: turn on =============== ============================================
drivers/hwmon/sht4x.c +136 -1
179 lines not on this page · raw message
Signature · 1 line
2.25.1
Guenter Roeck
maintainerQuoted 5 lines · Antoni Pokusinski
Add support for manipulating the internal heater of sht4x devices.
The heater can operate at three heating levels (20, 110 or 200 milliwatts). Also, two heating durations may be selected (0.1 or 1s). Once the heating time elapses the heater is automatically switched off.
This doesn't explain why this set of attributes is necessary. What is the use that makes this necessary now when it wasn't needed before ?
For non-standard attributes you need to explain why they are necessary, I do n't accept such attributes without rationale and an actual use case.
Quoted 68 lines
--- Documentation/hwmon/sht4x.rst | 10 +++ drivers/hwmon/sht4x.c | 137 +++++++++++++++++++++++++++++++++- 2 files changed, 146 insertions(+), 1 deletion(-)Documentation/hwmon/sht4x.rst +10
-0@@ -42,4 +42,14 @@ humidity1_input Measured humidity in %H update_interval The minimum interval for polling the sensor, in milliseconds. Writable. Must be at least 2000. +heater_power The requested heater power, in milliwatts. + Available values: 20, 110, 200 (default: 200). +heater_time The requested operating time of the heater, + in milliseconds. + Available values: 100, 1000 (default 1000). +heater_enable Enable the heater with the selected power + and for the selected time. Write-only. + + - 0: turn off + - 1: turn on =============== ============================================drivers/hwmon/sht4x.c +11
-0@@ -11,6 +11,7 @@#include <linux/crc8.h> #include <linux/delay.h> #include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> #include <linux/i2c.h> #include <linux/jiffies.h> #include <linux/module.h> @@ -31,6 +32,12 @@*/ #define SHT4X_CMD_MEASURE_HPM 0b11111101#define SHT4X_CMD_RESET 0b10010100 +#define SHT4X_CMD_HEATER_20_1 0b00011110 +#define SHT4X_CMD_HEATER_20_01 0b00010101 +#define SHT4X_CMD_HEATER_110_1 0b00101111 +#define SHT4X_CMD_HEATER_110_01 0b00100100 +#define SHT4X_CMD_HEATER_200_1 0b00111001 +#define SHT4X_CMD_HEATER_200_01 0b00110010#define SHT4X_CMD_LEN 1#define SHT4X_CRC8_LEN 1@@ -54,6 +61,8 @@ DECLARE_CRC8_TABLE(sht4x_crc8_table);* @last_updated: the previous time that the SHT4X was polled * @temperature: the latest temperature value received from the SHT4X * @humidity: the latest humidity value received from the SHT4X +* @heater_power: the power at which the heater will be started +* @heater_time: the time for which the heater will remain turned on */ struct sht4x_data {struct i2c_client *client;@@ -63,6 +72,8 @@ struct sht4x_data {long last_updated;/* in jiffies */ s32 temperature;s32 humidity; +u32 heater_power;/* in milli-watts */ +u32 heater_time;/* in milli-seconds */ };/**
drivers/hwmon/sht4x.c static int sht4x_hwmon_write(struct device *dev, enum hwmon_sensor_types type, · line 234
Quoted 9 lines
drivers/hwmon/sht4x.c +6
-0@@ -215,6 +226,128 @@ static int sht4x_hwmon_write(struct device *dev, enum hwmon_sensor_types type, } } +static ssize_t heater_enable_show (struct device *dev, +struct device_attribute *attr, +char *buf) +{ +return -EOPNOTSUPP ; +}
Why mark the attribute as readable when it isn't ?
drivers/hwmon/sht4x.c static int sht4x_hwmon_write(struct device *dev, enum hwmon_sensor_types type, · line 244
Quoted 10 lines
drivers/hwmon/sht4x.c +10
-0+ +static ssize_t heater_enable_store (struct device *dev, +struct device_attribute *attr, +const char *buf, +size_t count) +{ +struct sht4x_data *data =dev_get_drvdata (dev); +bool status; +ssize_t ret; +u8 cmd[SHT4X_CMD_LEN ];
What is the point of making this a single-byte array ?
Quoted 13 lines
drivers/hwmon/sht4x.c +13
-0+ + ret =kstrtobool (buf, &status); +if (ret) +return ret; + +if (status) { +if (data->heater_power ==20 ) { +if (data->heater_time ==100 ) + *cmd =SHT4X_CMD_HEATER_20_01 ; +else /* data->heater_time == 1000 */ + *cmd =SHT4X_CMD_HEATER_20_1 ; + }else if (data->heater_power ==110 ) { +if (data->heater_time ==100 )
drivers/hwmon/sht4x.c static int sht4x_hwmon_write(struct device *dev, enum hwmon_sensor_types type, · line 267
Quoted 10 lines
drivers/hwmon/sht4x.c +10
-0+ *cmd =SHT4X_CMD_HEATER_110_01 ; + else /* data->heater_time == 1000 */ + *cmd =SHT4X_CMD_HEATER_110_1 ; + }else if (data->heater_power ==200 ) { +if (data->heater_time ==100 ) + *cmd =SHT4X_CMD_HEATER_200_01 ; +else /* data->heater_time == 1000 */ + *cmd =SHT4X_CMD_HEATER_200_1 ; + }else { +return -EINVAL ;
This data path is never reached.
drivers/hwmon/sht4x.c static int sht4x_hwmon_write(struct device *dev, enum hwmon_sensor_types type, · line 272
Quoted 5 lines
drivers/hwmon/sht4x.c +5
-0+ } + } + +mutex_lock (&data->lock); + ret =i2c_master_send (data->client, cmd,SHT4X_CMD_LEN );
If status==false this sends a random byte to the chip because 'cmd' is not initialized. What is the point of doing that ?
drivers/hwmon/sht4x.c static int sht4x_hwmon_write(struct device *dev, enum hwmon_sensor_types type, · line 273
Quoted 1 line
drivers/hwmon/sht4x.c +1
-0+mutex_unlock (&data->lock);
This lock doesn't protect anything.
Quoted 57 lines
drivers/hwmon/sht4x.c +57
-0+ +return ret; +} + +static ssize_t heater_power_show (struct device *dev, +struct device_attribute *attr, +char *buf) +{ +struct sht4x_data *data =dev_get_drvdata (dev); + +return sysfs_emit (buf,"%u\n" , data->heater_power); +} + +static ssize_t heater_power_store (struct device *dev, +struct device_attribute *attr, +const char *buf, +size_t count) +{ +struct sht4x_data *data =dev_get_drvdata (dev); +u32 power; +ssize_t ret; + + ret =kstrtou32 (buf,10 , &power); +if (ret) +return ret; + +if (power !=20 && power !=110 && power !=200 ) +return -EINVAL ; + + data->heater_power = power; + +return count; +} + +static ssize_t heater_time_show (struct device *dev, +struct device_attribute *attr, +char *buf) +{ +struct sht4x_data *data =dev_get_drvdata (dev); + +return sysfs_emit (buf,"%u\n" , data->heater_time); +} + +static ssize_t heater_time_store (struct device *dev, +struct device_attribute *attr, +const char *buf, +size_t count) +{ +struct sht4x_data *data =dev_get_drvdata (dev); +u32 time; +ssize_t ret; + + ret =kstrtou32 (buf,10 , &time); +if (ret) +return ret; + +if (time !=100 && time !=1000 )
drivers/hwmon/sht4x.c static int sht4x_hwmon_write(struct device *dev, enum hwmon_sensor_types type, · line 340
Quoted 10 lines
drivers/hwmon/sht4x.c +10
-0+return -EINVAL ; + + data->heater_time = time; + +return count; +} + +static SENSOR_DEVICE_ATTR_RW(heater_enable, heater_enable, 0); +static SENSOR_DEVICE_ATTR_RW(heater_power, heater_power, 0); +static SENSOR_DEVICE_ATTR_RW(heater_time, heater_time, 0);
Why SENSOR_DEVICE_ATTR and not just DEVICE_ATTR ?
Quoted 34 lines
drivers/hwmon/sht4x.c +13
-1+ +static struct attribute *sht4x_attrs[] = { + &sensor_dev_attr_heater_enable.dev_attr.attr, + &sensor_dev_attr_heater_power.dev_attr.attr, + &sensor_dev_attr_heater_time.dev_attr.attr, +NULL +}; + +ATTRIBUTE_GROUPS (sht4x); +static const struct hwmon_channel_info *const sht4x_info[] = {HWMON_CHANNEL_INFO (chip,HWMON_C_UPDATE_INTERVAL ),HWMON_CHANNEL_INFO (temp,HWMON_T_INPUT ),@@ -255,6 +388,8 @@ static int sht4x_probe(struct i2c_client *client) data->update_interval =SHT4X_MIN_POLL_INTERVAL ; data->client = client; + data->heater_power =200 ; + data->heater_time =1000 ;mutex_init (&data->lock);@@ -270,7 +405,7 @@ static int sht4x_probe(struct i2c_client *client) client->name, data, &sht4x_chip_info, - NULL); + sht4x_groups);return PTR_ERR_OR_ZERO (hwmon_dev); }Signature · 1 line
2.25.1