dt-bindings: hwmon/regulator: Convert ltc2978.txt to yaml
Subsystems (4)
Frank Li
maintainerPATCH v3 1/1 dt-bindings: hwmon/regulator: Convert ltc2978.txt to yaml
Convert binding doc ltc2978.txt to yaml format.
Additional change:
- add i2c node.
- basic it is regulator according to example, move it under regulator.
Fix below warning:arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-cx.dtb: /soc/i2c@2000000/i2c-mux@77/i2c@2/regulator@5c:
failed to match any schema with compatible: ['lltc,ltc3882']
---
Change from v2 to v3
- put my name into maintainers.
change from v1 to v2
- maintainer change to Mark Brown <[email protected]> (regulator maintainer)
- update title to (from ltc2978 data sheet).
octal, digital power-supply monitor, supervisor, sequencer, and margin controller.
--- .../devicetree/bindings/hwmon/ltc2978.txt | 62 ------------ .../bindings/regulator/lltc,ltc2972.yaml | 94 +++++++++++++++++++ 2 files changed, 94 insertions(+), 62 deletions(-) delete mode 100644 Documentation/devicetree/bindings/hwmon/ltc2978.txt create mode 100644 Documentation/devicetree/bindings/regulator/lltc,ltc2972.yaml
Documentation/devicetree/bindings/hwmon/ltc2978.txt deleted +0 -62
@@ -1,62 +0,0 @@ -ltc2978 - -Required properties: -- compatible: should contain one of: - * "lltc,ltc2972" - * "lltc,ltc2974" - * "lltc,ltc2975" - * "lltc,ltc2977" - * "lltc,ltc2978" - * "lltc,ltc2979" - * "lltc,ltc2980" - * "lltc,ltc3880" - * "lltc,ltc3882" - * "lltc,ltc3883" - * "lltc,ltc3884" - * "lltc,ltc3886" - * "lltc,ltc3887" - * "lltc,ltc3889" - * "lltc,ltc7880" - * "lltc,ltm2987" - * "lltc,ltm4664" - * "lltc,ltm4675" - * "lltc,ltm4676" - * "lltc,ltm4677" - * "lltc,ltm4678" - * "lltc,ltm4680" - * "lltc,ltm4686" - * "lltc,ltm4700" -- reg: I2C slave address - -Optional properties: -- regulators: A node that houses a sub-node for each regulator controlled by - the device. Each sub-node is identified using the node's name, with valid - values listed below. The content of each sub-node is defined by the - standard binding for regulators; see regulator.txt. - -Valid names of regulators depend on number of supplies supported per device: - * ltc2972 vout0 - vout1 - * ltc2974, ltc2975 : vout0 - vout3 - * ltc2977, ltc2979, ltc2980, ltm2987 : vout0 - vout7 - * ltc2978 : vout0 - vout7 - * ltc3880, ltc3882, ltc3884, ltc3886, ltc3887, ltc3889 : vout0 - vout1 - * ltc7880 : vout0 - vout1 - * ltc3883 : vout0 - * ltm4664 : vout0 - vout1 - * ltm4675, ltm4676, ltm4677, ltm4678 : vout0 - vout1 - * ltm4680, ltm4686 : vout0 - vout1 - * ltm4700 : vout0 - vout1 - -Example: -ltc2978@5e { - compatible = "lltc,ltc2978"; - reg = <0x5e>; - regulators { - vout0 { - regulator-name = "FPGA-2.5V"; - }; - vout2 { - regulator-name = "FPGA-1.5V"; - }; - }; -};
Documentation/devicetree/bindings/regulator/lltc,ltc2972.yaml new file +94 -0
94 lines not on this page · raw message
Signature · 1 line
2.34.1
Rob Herring
maintainerQuoted 17 lines · Frank Li
Convert binding doc ltc2978.txt to yaml format.
Additional change:
- add i2c node.
- basic it is regulator according to example, move it under regulator.Fix below warning:
arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-cx.dtb: /soc/i2c@2000000/i2c-mux@77/i2c@2/regulator@5c:
failed to match any schema with compatible: ['lltc,ltc3882']Signed-off-by Frank Li <[email protected]>---
Change from v2 to v3
- put my name into maintainers.
change from v1 to v2
- maintainer change to Mark Brown <[email protected]> (regulator maintainer)
- update title to (from ltc2978 data sheet).
octal, digital power-supply monitor, supervisor, sequencer, and margin controller.
Quoted 6 lines
--- .../devicetree/bindings/hwmon/ltc2978.txt | 62 ------------ .../bindings/regulator/lltc,ltc2972.yaml | 94 +++++++++++++++++++ 2 files changed, 94 insertions(+), 62 deletions(-) delete mode 100644 Documentation/devicetree/bindings/hwmon/ltc2978.txt create mode 100644 Documentation/devicetree/bindings/regulator/lltc,ltc2972.yaml
Based on the discussion, I think it is easier if we just leave this under hwmon.
Rob
Frank Li
maintainerQuoted 25 lines · Rob Herring
Quoted 17 lines · Frank Li
Convert binding doc ltc2978.txt to yaml format.
Additional change:
- add i2c node.
- basic it is regulator according to example, move it under regulator.Fix below warning:
arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-cx.dtb: /soc/i2c@2000000/i2c-mux@77/i2c@2/regulator@5c:
failed to match any schema with compatible: ['lltc,ltc3882']Signed-off-by Frank Li <[email protected]>---
Change from v2 to v3
- put my name into maintainers.
change from v1 to v2
- maintainer change to Mark Brown <[email protected]> (regulator maintainer)
- update title to (from ltc2978 data sheet).
octal, digital power-supply monitor, supervisor, sequencer, and margin controller.Quoted 6 lines
--- .../devicetree/bindings/hwmon/ltc2978.txt | 62 ------------ .../bindings/regulator/lltc,ltc2972.yaml | 94 +++++++++++++++++++ 2 files changed, 94 insertions(+), 62 deletions(-) delete mode 100644 Documentation/devicetree/bindings/hwmon/ltc2978.txt create mode 100644 Documentation/devicetree/bindings/regulator/lltc,ltc2972.yaml
Quoted 2 lines
Based on the discussion, I think it is easier if we just leave this under hwmon.
Okay, I will new patch for it.
Quoted 2 lines
Rob