X1E Dell XPS 9345 support
v2 cover X1E Dell XPS 9345 support
Introduce support for the mentioned laptop.
Very similar to other X1E laptops, device tree was derived by analyzing dtsi of existing models and ACPI tables of this laptop [1]. Most notable difference were
* TZ protected SPI19.
* Keyboard only working after suspend/resume sequence, will do a follow up patch to i2c-hid.
* Lots of small deviations in LDOs voltages.
Successfully tested with Debian 12 and Gnome, although this required additional patches, namely harcode GPU chipid, apply [2] and _revert_ [3] - same as in Abel Vesa's branches. Without last two the boot process is terminated by TZ. Firmware for GPU/aDSP/cDSP was extracted from Windows, WiFi firmware from upstream linux-firmware.
Quite a few things alraedy work, details in patches, quite a few still in WIP or TODOs. Since fixing these may take me a while due to lack of documentation, sending current progress as its very much usable.
[1] https://github.com/aarch64-laptops/build/blob/master/misc/dell-xps-9345/acpi/DSDT.dsl
[2] https://lore.kernel.org/all/[email protected]/
[3] https://lore.kernel.org/all/[email protected]/
--------
Changes to V1:
* Fix misalignments due to wrong tab/space conversion
* Fix regulator namings
* Fix reasonable warnings from scripts/checkpatch.pl
* Restructure all (sub)nodes alphabetically
Aleksandrs Vinarskis (3):
dt-bindings: arm: qcom: Add Dell XPS 13 9345
firmware: qcom: scm: Allow QSEECOM on Dell XPS 13 9345
arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
.../devicetree/bindings/arm/qcom.yaml | 1 + arch/arm64/boot/dts/qcom/Makefile | 1 + .../dts/qcom/x1e80100-dell-tributo-13.dts | 860 ++++++++++++++++++ drivers/firmware/qcom/qcom_scm.c | 1 + 4 files changed, 863 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts
Signature · 1 line
2.43.0
PATCH v2 1/3 dt-bindings: arm: qcom: Add Dell XPS 13 9345
Document the X1E80100-based Dell XPS 9345 laptop, platform codenamed 'Tributo'/'Tributo R'.
--- Documentation/devicetree/bindings/arm/qcom.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/qcom.yaml +1 -0
@@ -1058,6 +1058,7 @@ properties: - items: - enum: - asus,vivobook-s15 + - dell,tributo-13 - lenovo,yoga-slim7x - microsoft,romulus13 - microsoft,romulus15
Signature · 1 line
2.43.0
Re: [PATCH v2 1/3] dt-bindings: arm: qcom: Add Dell XPS 13 9345
Quoted 4 lines · Aleksandrs Vinarskis
Document the X1E80100-based Dell XPS 9345 laptop, platform codenamed 'Tributo'/'Tributo R'.
Signed-off-by Aleksandrs Vinarskis <[email protected]>
<form letter>
This is a friendly reminder during the review process.
It looks like you received a tag and forgot to add it.
If you do not know the process, here is a short explanation:
Please add Acked-by/Reviewed-by/Tested-by tags when posting new versions, under or above your Signed-off-by tag. Tag is "received", when provided in a message replied to you on the mailing list. Tools like b4 can help here. However, there's no need to repost patches *only* to add the tags. The upstream maintainer will do that for tags received on the version they apply.
https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577
If a tag was not added on purpose, please state why and what changed. </form letter>
Best regards,
Krzysztof
PATCH v2 2/3 firmware: qcom: scm: Allow QSEECOM on Dell XPS 13 9345
In reply to Aleksandrs VinarskisAllow particular machine accessing eg. efivars.
--- drivers/firmware/qcom/qcom_scm.c | 1 + 1 file changed, 1 insertion(+)
drivers/firmware/qcom/qcom_scm.c +1 -0
@@ -1731,6 +1731,7 @@ EXPORT_SYMBOL_GPL(qcom_scm_qseecom_app_send);+ any potential issues with this, only allow validated machines for now. */ static const struct of_device_id qcom_scm_qseecom_allowlist[]__maybe_unused = { + { .compatible ="dell,tributo-13" }, { .compatible ="lenovo,flex-5g" }, { .compatible ="lenovo,thinkpad-t14s" }, { .compatible ="lenovo,thinkpad-x13s" , },
Signature · 1 line
2.43.0
PATCH v2 3/3 arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
In reply to Aleksandrs VinarskisInitial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resume
Not working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery Info
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panels
* Touchscreen
--- arch/arm64/boot/dts/qcom/Makefile | 1 + .../dts/qcom/x1e80100-dell-tributo-13.dts | 860 ++++++++++++++++++ 2 files changed, 861 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts
arch/arm64/boot/dts/qcom/Makefile +1 -0
@@ -271,6 +271,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e78100-lenovo-thinkpad-t14s.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-asus-vivobook-s15.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb +dtb-$(CONFIG_ARCH_QCOM) += x1e80100-dell-tributo-13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-lenovo-yoga-slim7x.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus15.dtb
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts new file +860 -0
860 lines not on this page · raw message
Signature · 1 line
2.43.0
Bjorn Andersson
maintainerRe: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
Quoted 1 line · Aleksandrs Vinarskis
Initial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Very nice.
Quoted 4 lines
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)
Hitting scroll lock/unlock on a USB keyboard once fixes this issue for me as well. Looking forward to your WIP patch.
Quoted 8 lines
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resume
Quoted 7 lines
Not working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery Info
Adding the ADSP firmware gave me both battery status and info, but perhaps you're hitting the previously reported issue in pmic_glink?
Quoted 3 lines
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panels
I tried closing the lid and opening it again (which I believe is what was reported to not work on the other devices), and that seems to work fine.
Quoted 1 line
* Touchscreen
See below
Quoted 1 line
[..]
Quoted 1 line
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +0
-0
[..]
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts line 514
Quoted 8 lines
+&i2c8 {
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +7
-0+ clock-frequency = <400000>; + + status = "okay"; + + touchscreen@0 { + compatible = "hid-over-i2c"; + reg = <0x0>;
Make this 0x10 (and update the unit address accordingly) and we have touchscreen.
Quoted 8 lines
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +8
-0+ + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&ts0_default>; + pinctrl-names = "default"; + }; +};
[..]
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts line 553
Quoted 2 lines
+&mdss_dp3 {
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +1
-0+ compatible = "qcom,x1e80100-dp";
This isn't needed, right?
[..]
Quoted 1 line
+&uart21 {
This fails to probe, because we don't have an alias for it, which in turn prevents sync_state on interconnects...
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts line 797
Quoted 4 lines
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +4
-0+ compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; +
Regards,
Bjorn
Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
Quoted 7 lines · Bjorn Andersson
Quoted 1 line · Aleksandrs Vinarskis
Initial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Very nice.
Quoted 1 line
Quoted 6 lines
Quoted 3 lines
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)Hitting scroll lock/unlock on a USB keyboard once fixes this issue for me as well. Looking forward to your WIP patch.
Thanks for your review.
Just submitted the series [3].
Quoted 17 lines
Quoted 9 lines
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resumeQuoted 7 lines
Not working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery Info
Quoted 3 lines
Adding the ADSP firmware gave me both battery status and info, but perhaps you're hitting the previously reported issue in
pmic_glink?
Could you please share a bug report for the mentioned issue?
Were you running with [2] patch reverted or not? Without reverting it, I cannot boot Ubuntu at all - it is spamming qcom_battmngr errors and holding services back.
With patch reverted I do not get any battery related info, which I guess makes sense. I tried applying [1], however it did help.
There are a few pmic_glink related errors in dmesg, so perhaps its related.
Quoted 16 lines
Quoted 3 lines
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panelsI tried closing the lid and opening it again (which I believe is what was reported to not work on the other devices), and that seems to work fine.
Quoted 1 line
* Touchscreen
See below
Quoted 1 line
[..]
Quoted 1 line
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +0
-0[..]
Quoted 11 lines
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts line 514
Quoted 8 lines
+&i2c8 {
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +7
-0+ clock-frequency = <400000>; + + status = "okay"; + + touchscreen@0 { + compatible = "hid-over-i2c"; + reg = <0x0>;Make this
0x10(and update the unit address accordingly) and we have touchscreen.
Awesome, thanks for testing. Will add it.
Do you have an OLED variant, or high-res IPS? Will update description when respinning to include it.
Thinking about it, perhaps depending on the OLED/IPS variant they have different touchscreen models with different addresses? I find it weird that the address was 0 as per ACPI.
Quoted 9 lines
Quoted 8 lines
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +8
-0+ + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&ts0_default>; + pinctrl-names = "default"; + }; +};[..]
Quoted 4 lines
Quoted 2 lines
+&mdss_dp3 {
+ compatible = "qcom,x1e80100-dp";This isn't needed, right?
Indeed. Will fix it.
Quoted 7 lines
[..]
Quoted 1 line
+&uart21 {
This fails to probe, because we don't have an alias for it, which in turn prevents
sync_stateon interconnects...
Indeed. Will fix it.
Thanks,
Alex
[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/all/[email protected]/
[3] https://lore.kernel.org/all/[email protected]/
Quoted 7 lines
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts line 797
Quoted 4 lines
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +4
-0+ compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; +Regards,
Bjorn
Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
Quoted 12 lines · Aleksandrs Vinarskis
Quoted 11 lines · Bjorn Andersson
Quoted 1 line · Aleksandrs Vinarskis
Initial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Very nice.
Quoted 4 lines
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)
Quoted 6 lines
Quoted 2 lines
Hitting scroll lock/unlock on a USB keyboard once fixes this issue for me as well. Looking forward to your WIP patch.
Thanks for your review.
Just submitted the series [3].
Thank you.
Quoted 17 lines
Quoted 17 lines
Quoted 16 lines
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resumeNot working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery Info
Quoted 6 lines
Quoted 3 lines
Adding the ADSP firmware gave me both battery status and info, but perhaps you're hitting the previously reported issue in
pmic_glink?Could you please share a bug report for the mentioned issue?
I'm referring to https://lore.kernel.org/all/[email protected]/
although I'm not sure where it was first reported.
Chris Lew has been debugging this and the problem relates to intent allocation in the underlying GLINK driver. We're discussing how to fix this.
Hoping to conclude the discussion within the coming days.
Quoted 1 line
Were you running with [2] patch reverted or not?
I applied your patches on next-20240924, no other changes.
Quoted 5 lines
Without reverting it, I cannot boot Ubuntu at all - it is spamming
qcom_battmngrerrors and holding services back.
With patch reverted I do not get any battery related info, which I guess makes sense. I tried applying [1], however it did help.
I think we want [1], but with a better argumentation. It's however unrelated to the problem you're seeing.
Quoted 2 lines
There are a few
pmic_glinkrelated errors in dmesg, so perhaps its related.
I do have a few messages about "unknown notification", but it works fine. I expect this is just luck...
Quoted 28 lines
Quoted 16 lines
Quoted 3 lines
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panelsI tried closing the lid and opening it again (which I believe is what was reported to not work on the other devices), and that seems to work fine.
Quoted 1 line
* Touchscreen
See below
Quoted 1 line
[..]
Quoted 1 line
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +0
-0[..]
Quoted 11 lines
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts line 514
Quoted 8 lines
+&i2c8 {
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +7
-0+ clock-frequency = <400000>; + + status = "okay"; + + touchscreen@0 { + compatible = "hid-over-i2c"; + reg = <0x0>;Make this
0x10(and update the unit address accordingly) and we have touchscreen.
Quoted 3 lines
Awesome, thanks for testing. Will add it.
Do you have an OLED variant, or high-res IPS? Will update description when respinning to include it.
I have the OLED screen.
Quoted 5 lines
Thinking about it, perhaps depending on the OLED/IPS variant they have different touchscreen models with different addresses? I find it weird that the address was 0 as per ACPI.
The 0 is indeed weird, I don't know what's up with that.
I'd suggest that we start with 0x10 and then change things from there if necessary.
Regards,
Bjorn
Quoted 41 lines
Quoted 9 lines
Quoted 8 lines
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +8
-0+ + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&ts0_default>; + pinctrl-names = "default"; + }; +};[..]
Quoted 4 lines
Quoted 2 lines
+&mdss_dp3 {
+ compatible = "qcom,x1e80100-dp";This isn't needed, right?
Indeed. Will fix it.
Quoted 7 lines
[..]
Quoted 1 line
+&uart21 {
This fails to probe, because we don't have an alias for it, which in turn prevents
sync_stateon interconnects...Indeed. Will fix it.
Thanks,
Alex[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/all/[email protected]/
[3] https://lore.kernel.org/all/[email protected]/Quoted 7 lines
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts line 797
Quoted 4 lines
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts +4
-0+ compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; +Regards,
Bjorn
Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
In reply to Aleksandrs VinarskisQuoted 22 lines · Aleksandrs Vinarskis
Initial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resumeNot working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery Info
Quoted 3 lines
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panels
* Touchscreen
A follow up to the display discussion thread [1] - Peter de Kraker has tested these changes on his OLED setup, a few findings:
* OLED panel works out of the box, with edp-panel compatible. Turns on, turns Off on suspend, turns On on resume. Will update description when respinning to reflect this.
* As per Bjorn Andersson's correction, the touchscreen was tested and confirmed to be working with 0x10 address. No other i2c devices are detected on that bus. Will update description when respinning to reflect this.
* SKU/HWIDs of OLED and non-touch IPS models are 1:1 the same
* For reference, non-touch IPS panel is 'LQ134N1' according to EDID
Regards,
Alex
[1] https://lore.kernel.org/all/CAF6AEGtrQzcMFsWCd-JzVFmF1sRk3vgy=L1q4Lzp+K1a4fuRnw@mail.gmail.com/
[...]
Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
In reply to Aleksandrs VinarskisHi Alex,
Thanks for this! Comment inline.
Quoted 21 lines · Aleksandrs Vinarskis
Initial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resumeNot working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery Info
Quoted 8 lines
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panels
* TouchscreenSigned-off-by Aleksandrs Vinarskis <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 1 + .../dts/qcom/x1e80100-dell-tributo-13.dts | 860 ++++++++++++++++++
Could you please use the marketing name for the device tree file name & machine compatible, e.g. "x1e80100-dell-xps13-9345.dts" for the dts file and "dell,xps13-9345" for the compat? I'm thinking that this will help people to identify it more easily.
---
Thanks & Best Regards, Laurentiu
Quoted 883 lines
2 files changed, 861 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dtsarch/arm64/boot/dts/qcom/Makefile +1
-0@@ -271,6 +271,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e78100-lenovo-thinkpad-t14s.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-asus-vivobook-s15.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb +dtb-$(CONFIG_ARCH_QCOM) += x1e80100-dell-tributo-13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-lenovo-yoga-slim7x.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus15.dtbarch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts new file +860
-0@@ -0,0 +1,860 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + * Copyright (c) 2024 Aleksandrs Vinarskis <[email protected]> + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +#include "x1e80100.dtsi" +#include "x1e80100-pmics.dtsi" + +/ { + model = "Dell XPS 13 9345"; + compatible = "dell,tributo-13", "qcom,x1e80100"; + chassis-type = "laptop"; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&hall_int_n_default>; + pinctrl-names = "default"; + + switch-lid { + gpios = <&tlmm 92 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + wakeup-source; + wakeup-event-action = <EV_ACT_DEASSERTED>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&cam_indicator_en>; + + led-camera-indicator { + label = "white:camera-indicator"; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_WHITE>; + gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + /* Reuse as a panic indicator until we get a "camera on" trigger */ + panic-indicator; + }; + }; + + pmic-glink { + compatible = "qcom,x1e80100-pmic-glink", + "qcom,sm8550-pmic-glink", + "qcom,pmic-glink"; + orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, + <&tlmm 123 GPIO_ACTIVE_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + /* Right-side USB Type-C port */ + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss0_hs_in: endpoint { + remote-endpoint = <&usb_1_ss0_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss0_ss_in: endpoint { + remote-endpoint = <&usb_1_ss0_qmpphy_out>; + }; + }; + }; + }; + + /* Left-side USB Type-C port */ + connector@1 { + compatible = "usb-c-connector"; + reg = <1>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss1_hs_in: endpoint { + remote-endpoint = <&usb_1_ss1_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss1_ss_in: endpoint { + remote-endpoint = <&usb_1_ss1_qmpphy_out>; + }; + }; + }; + }; + }; + + reserved-memory { + linux,cma { + compatible = "shared-dma-pool"; + size = <0x0 0x8000000>; + reusable; + linux,cma-default; + }; + }; + + vreg_edp_3p3: regulator-edp-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_EDP_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&edp_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_nvme: regulator-nvme { + compatible = "regulator-fixed"; + + regulator-name = "VREG_NVME_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&nvme_reg_en>; + pinctrl-names = "default"; + }; + + vreg_vph_pwr: regulator-vph-pwr { + compatible = "regulator-fixed"; + + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8550-rpmh-regulators"; + qcom,pmic-id = "b"; + vdd-bob1-supply = <&vreg_vph_pwr>; + vdd-bob2-supply = <&vreg_vph_pwr>; + vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; + vdd-l2-l13-l14-supply = <&vreg_bob1>; + vdd-l5-l16-supply = <&vreg_bob1>; + vdd-l6-l7-supply = <&vreg_bob2>; + vdd-l8-l9-supply = <&vreg_bob1>; + vdd-l12-supply = <&vreg_s5j_1p2>; + vdd-l15-supply = <&vreg_s4c_1p8>; + vdd-l17-supply = <&vreg_bob2>; + + vreg_bob1: bob1 { + regulator-name = "vreg_bob1"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob2: bob2 { + regulator-name = "vreg_bob2"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-name = "vreg_l2b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4b_1p8: ldo4 { + regulator-name = "vreg_l4b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p8: ldo6 { + regulator-name = "vreg_l6b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8b_3p0: ldo8 { + regulator-name = "vreg_l8b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_2p9: ldo9 { + regulator-name = "vreg_l9b_2p9"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12b_1p2: ldo12 { + regulator-name = "vreg_l12b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13b_3p0: ldo13 { + regulator-name = "vreg_l13b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14b_3p0: ldo14 { + regulator-name = "vreg_l14b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15b_1p8: ldo15 { + regulator-name = "vreg_l15b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17b_2p5: ldo17 { + regulator-name = "vreg_l17b_2p5"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "c"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s1f_0p7>; + + vreg_s4c_1p8: smps4 { + regulator-name = "vreg_s4c_1p8"; + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1c_1p2: ldo1 { + regulator-name = "vreg_l1c_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c_0p8: ldo2 { + regulator-name = "vreg_l2c_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c_0p9: ldo3 { + regulator-name = "vreg_l3c_0p9"; + regulator-min-microvolt = <920000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "d"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s4c_1p8>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_l1d_0p8: ldo1 { + regulator-name = "vreg_l1d_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2d_0p9: ldo2 { + regulator-name = "vreg_l2d_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3d_1p8: ldo3 { + regulator-name = "vreg_l3d_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-3 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "e"; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s5j_1p2>; + + vreg_l2e_0p8: ldo2 { + regulator-name = "vreg_l2e_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3e_1p2: ldo3 { + regulator-name = "vreg_l3e_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-4 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "f"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s5j_1p2>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_s1f_0p7: smps1 { + regulator-name = "vreg_s1f_0p7"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-6 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "i"; + vdd-l1-supply = <&vreg_s4c_1p8>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s1-supply = <&vreg_vph_pwr>; + vdd-s2-supply = <&vreg_vph_pwr>; + + vreg_s1i_0p9: smps1 { + regulator-name = "vreg_s1i_0p9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s2i_1p0: smps2 { + regulator-name = "vreg_s2i_1p0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1i_1p8: ldo1 { + regulator-name = "vreg_l1i_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2i_1p2: ldo2 { + regulator-name = "vreg_l2i_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3i_0p8: ldo3 { + regulator-name = "vreg_l3i_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-7 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "j"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s5-supply = <&vreg_vph_pwr>; + + vreg_s5j_1p2: smps5 { + regulator-name = "vreg_s5j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1j_0p9: ldo1 { + regulator-name = "vreg_l1j_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2j_1p2: ldo2 { + regulator-name = "vreg_l2j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3j_0p8: ldo3 { + regulator-name = "vreg_l3j_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&gpu { + status = "okay"; + + zap-shader { + firmware-name = "qcom/x1e80100/dell/tributo/qcdxkmsuc8380.mbn"; + }; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + keyboard@5 { + compatible = "hid-over-i2c"; + reg = <0x5>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&kybd_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c5 { + clock-frequency = <100000>; + status = "disabled"; + /* Unknown device @0x3b */ +}; + +&i2c7 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c8 { + clock-frequency = <400000>; + + status = "okay"; + + touchscreen@0 { + compatible = "hid-over-i2c"; + reg = <0x0>; + + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&ts0_default>; + pinctrl-names = "default"; + }; +}; + +&i2c9 { + clock-frequency = <400000>; + status = "disabled"; + /* USB3 retimer device @0x4f */ +}; + +&i2c17 { + clock-frequency = <400000>; + status = "okay"; + + touchpad@2c { + compatible = "hid-over-i2c"; + reg = <0x2c>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&tpad_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp3 { + compatible = "qcom,x1e80100-dp"; + /delete-property/ #sound-dai-cells; + + status = "okay"; + + aux-bus { + panel { + /* 1920x1200 IPS panel is SHP1593, PNP09FF compatible */ + compatible = "edp-panel"; + power-supply = <&vreg_edp_3p3>; + + port { + edp_panel_in: endpoint { + remote-endpoint = <&mdss_dp3_out>; + }; + }; + }; + }; + + ports { + port@1 { + reg = <1>; + + mdss_dp3_out: endpoint { + data-lanes = <0 1 2 3>; + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; + + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +}; + +&mdss_dp3_phy { + vdda-phy-supply = <&vreg_l3j_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&pcie4 { + perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&pcie4_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie4_phy { + vdda-phy-supply = <&vreg_l3i_0p8>; + vdda-pll-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&pcie6a { + perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; + + vddpe-3v3-supply = <&vreg_nvme>; + + pinctrl-0 = <&pcie6a_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie6a_phy { + vdda-phy-supply = <&vreg_l1d_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&qupv3_0 { + status = "okay"; +}; + +&qupv3_1 { + status = "okay"; +}; + +&qupv3_2 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/x1e80100/dell/tributo/qcadsp8380.mbn", + "qcom/x1e80100/dell/tributo/adsp_dtbs.elf"; + + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/x1e80100/dell/tributo/qccdsp8380.mbn", + "qcom/x1e80100/dell/tributo/cdsp_dtbs.elf"; + + status = "okay"; +}; + +&smb2360_0_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l2b_3p0>; +}; + +&smb2360_1_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l14b_3p0>; +}; + +&tlmm { + gpio-reserved-ranges = <44 4>, /* SPI11 (TPM) */ + <76 4>, /* SPI19 (TZ Protected) */ + <238 1>; /* UFS Reset */ + + cam_indicator_en: cam-indicator-en-state { + pins = "gpio110"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + edp_reg_en: edp-reg-en-state { + pins = "gpio70"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + hall_int_n_default: hall-int-n-state { + pins = "gpio92"; + function = "gpio"; + + bias-disable; + }; + + kybd_default: kybd-default-state { + pins = "gpio67"; + function = "gpio"; + bias-pull-up; + }; + + nvme_reg_en: nvme-reg-en-state { + pins = "gpio18"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + pcie4_default: pcie4-default-state { + clkreq-n-pins { + pins = "gpio147"; + function = "pcie4_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio146"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio148"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie6a_default: pcie6a-default-state { + clkreq-n-pins { + pins = "gpio153"; + function = "pcie6a_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio152"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio154"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + tpad_default: tpad-default-state { + disable-pins { + pins = "gpio38"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio3"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + pins = "gpio52"; + function = "gpio"; + bias-disable; + }; + }; + + ts0_default: ts0-default-state { + disable-pins { + pins = "gpio75"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio51"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + /* Technically should be High-Z input */ + pins = "gpio48"; + function = "gpio"; + output-low; + drive-strength = <2>; + }; + }; +}; + +&uart21 { + compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; + +&usb_1_ss0_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_0_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss0_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l1j_0p9>; + + status = "okay"; +}; + +&usb_1_ss0 { + status = "okay"; +}; + +&usb_1_ss0_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss0_dwc3_hs { + remote-endpoint = <&pmic_glink_ss0_hs_in>; +}; + +&usb_1_ss0_qmpphy_out { + remote-endpoint = <&pmic_glink_ss0_ss_in>; +}; + +&usb_1_ss1_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_1_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss1_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l2d_0p9>; + + status = "okay"; +}; + +&usb_1_ss1 { + status = "okay"; +}; + +&usb_1_ss1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss1_dwc3_hs { + remote-endpoint = <&pmic_glink_ss1_hs_in>; +}; + +&usb_1_ss1_qmpphy_out { + remote-endpoint = <&pmic_glink_ss1_ss_in>; +};
Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
Quoted 37 lines · Laurentiu Tudor
Hi Alex,
Thanks for this! Comment inline.
Quoted 21 lines · Aleksandrs Vinarskis
Initial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resumeNot working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery InfoQuoted 8 lines
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panels
* TouchscreenSigned-off-by Aleksandrs Vinarskis <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 1 + .../dts/qcom/x1e80100-dell-tributo-13.dts | 860 ++++++++++++++++++
Quoted 4 lines
Could you please use the marketing name for the device tree file name & machine compatible, e.g. "
x1e80100-dell-xps13-9345.dts" for the dts file and "dell,xps13-9345" for the compat? I'm thinking that this will help people to identify it more easily.
Hi,
Even though I agree that it may be easier to identify for a non-developer, I am a bit skeptical as Dell has a pretty weird naming convention which sometimes results in the name being non-unique. In particular case - 9345 - 9 stands for XPS series, 3 stands for 13", and 45 would typically be the last digit of year + 0 (so 40), but with the introduction of last year's ''13 Plus"series they added a 5. At present, this is unique, however in 10 years it may not be.
I have recently hit this issue when working on Dell XPS 15" 2024 (9530), which has the same model number as Dell XPS 15" 2013 and led to huge confusions. Only way to distinguish them is by codename ('fiorano' for the newer one), or using a complete name including the year... The codename on the other hand is easily searchable both in the source code and online.
I tried to browse the source code for existing notation, but didn't find anything strongly supporting one or another way, so decided to follow Microsoft Surface's example with codenames ('romulus'). Codenaming is also imperfect though, as in Dell's case it typically refers to chassis, rather than _the_ particular device, which typically lasts several years. Typically throughout chassis generation internals stay +/- the same, but we can't know if any of the changes would be breaking. Perhaps then, x1e80100-dell-tributo-9345 and dell,tributo-9345 respectively, as this would be the shortest yet most complete description? 'Tributo' already implies its XPS 13" and chassis variation (touchar, hidden trackpad etc etc), '9345' implies XPS 13" of 2024 (?) and in combination with chassis variant pinpoints the model.
Otherwise, if it's strongly desired to use marketing names it can be reduced down to x1e80100-dell-9345.dts and dell,9345 altogether as 9345 implies it being both 'XPS' series and 13", and we can hope that by 2034 Dell won't repeat the same mistake with naming. Curious to hear maintainers' opinions as well.
P.S. I've sent the V3 version of the series, it probably makes sense to move this conversation there for visibility.
Alex
Quoted 888 lines
---
Thanks & Best Regards, LaurentiuQuoted 883 lines
2 files changed, 861 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dtsarch/arm64/boot/dts/qcom/Makefile +1
-0@@ -271,6 +271,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e78100-lenovo-thinkpad-t14s.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-asus-vivobook-s15.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb +dtb-$(CONFIG_ARCH_QCOM) += x1e80100-dell-tributo-13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-lenovo-yoga-slim7x.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus15.dtbarch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts new file +860
-0@@ -0,0 +1,860 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + * Copyright (c) 2024 Aleksandrs Vinarskis <[email protected]> + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +#include "x1e80100.dtsi" +#include "x1e80100-pmics.dtsi" + +/ { + model = "Dell XPS 13 9345"; + compatible = "dell,tributo-13", "qcom,x1e80100"; + chassis-type = "laptop"; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&hall_int_n_default>; + pinctrl-names = "default"; + + switch-lid { + gpios = <&tlmm 92 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + wakeup-source; + wakeup-event-action = <EV_ACT_DEASSERTED>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&cam_indicator_en>; + + led-camera-indicator { + label = "white:camera-indicator"; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_WHITE>; + gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + /* Reuse as a panic indicator until we get a "camera on" trigger */ + panic-indicator; + }; + }; + + pmic-glink { + compatible = "qcom,x1e80100-pmic-glink", + "qcom,sm8550-pmic-glink", + "qcom,pmic-glink"; + orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, + <&tlmm 123 GPIO_ACTIVE_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + /* Right-side USB Type-C port */ + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss0_hs_in: endpoint { + remote-endpoint = <&usb_1_ss0_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss0_ss_in: endpoint { + remote-endpoint = <&usb_1_ss0_qmpphy_out>; + }; + }; + }; + }; + + /* Left-side USB Type-C port */ + connector@1 { + compatible = "usb-c-connector"; + reg = <1>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss1_hs_in: endpoint { + remote-endpoint = <&usb_1_ss1_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss1_ss_in: endpoint { + remote-endpoint = <&usb_1_ss1_qmpphy_out>; + }; + }; + }; + }; + }; + + reserved-memory { + linux,cma { + compatible = "shared-dma-pool"; + size = <0x0 0x8000000>; + reusable; + linux,cma-default; + }; + }; + + vreg_edp_3p3: regulator-edp-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_EDP_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&edp_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_nvme: regulator-nvme { + compatible = "regulator-fixed"; + + regulator-name = "VREG_NVME_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&nvme_reg_en>; + pinctrl-names = "default"; + }; + + vreg_vph_pwr: regulator-vph-pwr { + compatible = "regulator-fixed"; + + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8550-rpmh-regulators"; + qcom,pmic-id = "b"; + vdd-bob1-supply = <&vreg_vph_pwr>; + vdd-bob2-supply = <&vreg_vph_pwr>; + vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; + vdd-l2-l13-l14-supply = <&vreg_bob1>; + vdd-l5-l16-supply = <&vreg_bob1>; + vdd-l6-l7-supply = <&vreg_bob2>; + vdd-l8-l9-supply = <&vreg_bob1>; + vdd-l12-supply = <&vreg_s5j_1p2>; + vdd-l15-supply = <&vreg_s4c_1p8>; + vdd-l17-supply = <&vreg_bob2>; + + vreg_bob1: bob1 { + regulator-name = "vreg_bob1"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob2: bob2 { + regulator-name = "vreg_bob2"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-name = "vreg_l2b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4b_1p8: ldo4 { + regulator-name = "vreg_l4b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p8: ldo6 { + regulator-name = "vreg_l6b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8b_3p0: ldo8 { + regulator-name = "vreg_l8b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_2p9: ldo9 { + regulator-name = "vreg_l9b_2p9"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12b_1p2: ldo12 { + regulator-name = "vreg_l12b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13b_3p0: ldo13 { + regulator-name = "vreg_l13b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14b_3p0: ldo14 { + regulator-name = "vreg_l14b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15b_1p8: ldo15 { + regulator-name = "vreg_l15b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17b_2p5: ldo17 { + regulator-name = "vreg_l17b_2p5"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "c"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s1f_0p7>; + + vreg_s4c_1p8: smps4 { + regulator-name = "vreg_s4c_1p8"; + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1c_1p2: ldo1 { + regulator-name = "vreg_l1c_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c_0p8: ldo2 { + regulator-name = "vreg_l2c_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c_0p9: ldo3 { + regulator-name = "vreg_l3c_0p9"; + regulator-min-microvolt = <920000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "d"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s4c_1p8>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_l1d_0p8: ldo1 { + regulator-name = "vreg_l1d_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2d_0p9: ldo2 { + regulator-name = "vreg_l2d_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3d_1p8: ldo3 { + regulator-name = "vreg_l3d_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-3 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "e"; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s5j_1p2>; + + vreg_l2e_0p8: ldo2 { + regulator-name = "vreg_l2e_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3e_1p2: ldo3 { + regulator-name = "vreg_l3e_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-4 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "f"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s5j_1p2>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_s1f_0p7: smps1 { + regulator-name = "vreg_s1f_0p7"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-6 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "i"; + vdd-l1-supply = <&vreg_s4c_1p8>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s1-supply = <&vreg_vph_pwr>; + vdd-s2-supply = <&vreg_vph_pwr>; + + vreg_s1i_0p9: smps1 { + regulator-name = "vreg_s1i_0p9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s2i_1p0: smps2 { + regulator-name = "vreg_s2i_1p0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1i_1p8: ldo1 { + regulator-name = "vreg_l1i_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2i_1p2: ldo2 { + regulator-name = "vreg_l2i_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3i_0p8: ldo3 { + regulator-name = "vreg_l3i_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-7 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "j"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s5-supply = <&vreg_vph_pwr>; + + vreg_s5j_1p2: smps5 { + regulator-name = "vreg_s5j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1j_0p9: ldo1 { + regulator-name = "vreg_l1j_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2j_1p2: ldo2 { + regulator-name = "vreg_l2j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3j_0p8: ldo3 { + regulator-name = "vreg_l3j_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&gpu { + status = "okay"; + + zap-shader { + firmware-name = "qcom/x1e80100/dell/tributo/qcdxkmsuc8380.mbn"; + }; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + keyboard@5 { + compatible = "hid-over-i2c"; + reg = <0x5>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&kybd_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c5 { + clock-frequency = <100000>; + status = "disabled"; + /* Unknown device @0x3b */ +}; + +&i2c7 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c8 { + clock-frequency = <400000>; + + status = "okay"; + + touchscreen@0 { + compatible = "hid-over-i2c"; + reg = <0x0>; + + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&ts0_default>; + pinctrl-names = "default"; + }; +}; + +&i2c9 { + clock-frequency = <400000>; + status = "disabled"; + /* USB3 retimer device @0x4f */ +}; + +&i2c17 { + clock-frequency = <400000>; + status = "okay"; + + touchpad@2c { + compatible = "hid-over-i2c"; + reg = <0x2c>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&tpad_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp3 { + compatible = "qcom,x1e80100-dp"; + /delete-property/ #sound-dai-cells; + + status = "okay"; + + aux-bus { + panel { + /* 1920x1200 IPS panel is SHP1593, PNP09FF compatible */ + compatible = "edp-panel"; + power-supply = <&vreg_edp_3p3>; + + port { + edp_panel_in: endpoint { + remote-endpoint = <&mdss_dp3_out>; + }; + }; + }; + }; + + ports { + port@1 { + reg = <1>; + + mdss_dp3_out: endpoint { + data-lanes = <0 1 2 3>; + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; + + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +}; + +&mdss_dp3_phy { + vdda-phy-supply = <&vreg_l3j_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&pcie4 { + perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&pcie4_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie4_phy { + vdda-phy-supply = <&vreg_l3i_0p8>; + vdda-pll-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&pcie6a { + perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; + + vddpe-3v3-supply = <&vreg_nvme>; + + pinctrl-0 = <&pcie6a_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie6a_phy { + vdda-phy-supply = <&vreg_l1d_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&qupv3_0 { + status = "okay"; +}; + +&qupv3_1 { + status = "okay"; +}; + +&qupv3_2 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/x1e80100/dell/tributo/qcadsp8380.mbn", + "qcom/x1e80100/dell/tributo/adsp_dtbs.elf"; + + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/x1e80100/dell/tributo/qccdsp8380.mbn", + "qcom/x1e80100/dell/tributo/cdsp_dtbs.elf"; + + status = "okay"; +}; + +&smb2360_0_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l2b_3p0>; +}; + +&smb2360_1_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l14b_3p0>; +}; + +&tlmm { + gpio-reserved-ranges = <44 4>, /* SPI11 (TPM) */ + <76 4>, /* SPI19 (TZ Protected) */ + <238 1>; /* UFS Reset */ + + cam_indicator_en: cam-indicator-en-state { + pins = "gpio110"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + edp_reg_en: edp-reg-en-state { + pins = "gpio70"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + hall_int_n_default: hall-int-n-state { + pins = "gpio92"; + function = "gpio"; + + bias-disable; + }; + + kybd_default: kybd-default-state { + pins = "gpio67"; + function = "gpio"; + bias-pull-up; + }; + + nvme_reg_en: nvme-reg-en-state { + pins = "gpio18"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + pcie4_default: pcie4-default-state { + clkreq-n-pins { + pins = "gpio147"; + function = "pcie4_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio146"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio148"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie6a_default: pcie6a-default-state { + clkreq-n-pins { + pins = "gpio153"; + function = "pcie6a_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio152"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio154"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + tpad_default: tpad-default-state { + disable-pins { + pins = "gpio38"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio3"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + pins = "gpio52"; + function = "gpio"; + bias-disable; + }; + }; + + ts0_default: ts0-default-state { + disable-pins { + pins = "gpio75"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio51"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + /* Technically should be High-Z input */ + pins = "gpio48"; + function = "gpio"; + output-low; + drive-strength = <2>; + }; + }; +}; + +&uart21 { + compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; + +&usb_1_ss0_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_0_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss0_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l1j_0p9>; + + status = "okay"; +}; + +&usb_1_ss0 { + status = "okay"; +}; + +&usb_1_ss0_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss0_dwc3_hs { + remote-endpoint = <&pmic_glink_ss0_hs_in>; +}; + +&usb_1_ss0_qmpphy_out { + remote-endpoint = <&pmic_glink_ss0_ss_in>; +}; + +&usb_1_ss1_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_1_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss1_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l2d_0p9>; + + status = "okay"; +}; + +&usb_1_ss1 { + status = "okay"; +}; + +&usb_1_ss1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss1_dwc3_hs { + remote-endpoint = <&pmic_glink_ss1_hs_in>; +}; + +&usb_1_ss1_qmpphy_out { + remote-endpoint = <&pmic_glink_ss1_ss_in>; +};
RE: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
Fascinating topic. First of all, thank you Alex for the explanation of your logic, and thank you as well for the work on the device tree for the XPS 13. I understand completely how the Dell naming/numbering scheme is confusing. The shortened version down to just the model number could also be confusing. For example, there is an XPS 9520 as well as a Latitude 9520. The 9 basically translates to "premium" not a specific line of business. For what it is worth, I would prefer the dell-xps13-9345 naming and I think we can have to be mindful to avoid a naming collision in a decade.
Thanks again for the support.
Bryan Kemp
Architect - Linux OS Engineering
Internal Use - Confidential
-----Original Message-----
From: Aleksandrs Vinarskis <[email protected]>
Sent: Monday, September 30, 2024 2:24 PM
To: Laurentiu Tudor <[email protected]>
Cc: Bjorn Andersson <[email protected]>; Krzysztof Kozlowski <[email protected]>; Dmitry Baryshkov <[email protected]>; [email protected]; [email protected]; [email protected]; Tudor, Laurentiu <[email protected]>; Konrad Dybcio <[email protected]>; Rob Herring <[email protected]>; Krzysztof Kozlowski <[email protected]>; Conor Dooley <[email protected]>; Rob Clark <[email protected]>; Peter de Kraker <[email protected]>; Kemp, Bryan <[email protected]>
Subject: Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
[EXTERNAL EMAIL]
Quoted 37 lines · Laurentiu Tudor
Hi Alex,
Thanks for this! Comment inline.
Quoted 21 lines · Aleksandrs Vinarskis
Initial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resumeNot working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery InfoQuoted 8 lines
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panels
* TouchscreenSigned-off-by Aleksandrs Vinarskis <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 1 +- .../dts/qcom/x1e80100-dell-tributo-13.dts | 860 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
Quoted 4 lines
Could you please use the marketing name for the device tree file name & machine compatible, e.g. "
x1e80100-dell-xps13-9345.dts" for the dts file and "dell,xps13-9345" for the compat? I'm thinking that this will help people to identify it more easily.
Hi,
Even though I agree that it may be easier to identify for a non-developer, I am a bit skeptical as Dell has a pretty weird naming convention which sometimes results in the name being non-unique.
In particular case - 9345 - 9 stands for XPS series, 3 stands for 13", and 45 would typically be the last digit of year +- 0 (so 40), but with the introduction of last year's ''13 Plus"series they added a 5. At present, this is unique, however in 10 years it may not be.
I have recently hit this issue when working on Dell XPS 15" 2024 (9530), which has the same model number as Dell XPS 15" 2013 and led to huge confusions. Only way to distinguish them is by codename ('fiorano' for the newer one), or using a complete name including the year... The codename on the other hand is easily searchable both in the source code and online.
I tried to browse the source code for existing notation, but didn't find anything strongly supporting one or another way, so decided to follow Microsoft Surface's example with codenames ('romulus').
Codenaming is also imperfect though, as in Dell's case it typically refers to chassis, rather than _the_ particular device, which typically lasts several years. Typically throughout chassis generation internals stay +-/- the same, but we can't know if any of the changes would be breaking. Perhaps then, x1e80100-dell-tributo-9345 and dell,tributo-9345 respectively, as this would be the shortest yet most complete description? 'Tributo' already implies its XPS 13" and chassis variation (touchar, hidden trackpad etc etc), '9345' implies XPS 13" of 2024 (?) and in combination with chassis variant pinpoints the model. Otherwise, if it's strongly desired to use marketing names it can be reduced down to x1e80100-dell-9345.dts and dell,9345 altogether as
9345 implies it being both 'XPS' series and 13", and we can hope that by 2034 Dell won't repeat the same mistake with naming. Curious to hear maintainers' opinions as well.
P.S. I've sent the V3 version of the series, it probably makes sense to move this conversation there for visibility.
Alex
Quoted 884 lines
---
Thanks & Best Regards, LaurentiuQuoted 879 lines
2 files changed, 861 insertions(+-)create mode 100644
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dtsarch/arm64/boot/dts/qcom/Makefile +1
-1--- a/arch/arm64/boot/dts/qcom/Makefile +-+-+- b/arch/arm64/boot/dts/qcom/Makefile@@ -271,6 +-271,7 @@ dtb-$(CONFIG_ARCH_QCOM) +-= sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) +-= x1e78100-lenovo-thinkpad-t14s.dtb dtb-$(CONFIG_ARCH_QCOM) +-= x1e80100-asus-vivobook-s15.dtb dtb-$(CONFIG_ARCH_QCOM) +-= x1e80100-crd.dtb +-dtb-$(CONFIG_ARCH_QCOM) +-= x1e80100-dell-tributo-13.dtb dtb-$(CONFIG_ARCH_QCOM) +-= x1e80100-lenovo-yoga-slim7x.dtb dtb-$(CONFIG_ARCH_QCOM) +-= x1e80100-microsoft-romulus13.dtb dtb-$(CONFIG_ARCH_QCOM) +-= x1e80100-microsoft-romulus15.dtbarch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts new file +1
-1--- /dev/null +-+-+- b/arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts@@ -0,0 +-1,860 @@
+-// SPDX-License-Identifier: BSD-3-Clause +-/* +- * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. +- * Copyright (c) 2024 Aleksandrs Vinarskis +-<[email protected]> */ +- +-/dts-v1/; +- +-#include <dt-bindings/gpio/gpio.h> +-#include <dt-bindings/input/gpio-keys.h> #include +-<dt-bindings/input/input.h> #include <dt-bindings/leds/common.h> +-#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +- +-#include "x1e80100.dtsi" +-#include "x1e80100-pmics.dtsi" +- +-/ { +- model = "Dell XPS 13 9345"; +- compatible = "dell,tributo-13", "qcom,x1e80100"; +- chassis-type = "laptop"; +- +- gpio-keys { +- compatible = "gpio-keys"; +- +- pinctrl-0 = <&hall_int_n_default>; +- pinctrl-names = "default"; +- +- switch-lid { +- gpios = <&tlmm 92 GPIO_ACTIVE_LOW>; +- linux,input-type = <EV_SW>; +- linux,code = <SW_LID>; +- wakeup-source; +- wakeup-event-action = <EV_ACT_DEASSERTED>; +- }; +- }; +- +- leds { +- compatible = "gpio-leds"; +- +- pinctrl-names = "default"; +- pinctrl-0 = <&cam_indicator_en>; +- +- led-camera-indicator { +- label = "white:camera-indicator"; +- function = LED_FUNCTION_INDICATOR; +- color = <LED_COLOR_ID_WHITE>; +- gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; +- linux,default-trigger = "none"; +- default-state = "off"; +- /* Reuse as a panic indicator until we get a "camera on" trigger */ +- panic-indicator; +- }; +- }; +- +- pmic-glink { +- compatible = "qcom,x1e80100-pmic-glink", +- "qcom,sm8550-pmic-glink", +- "qcom,pmic-glink"; +- orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, +- <&tlmm 123 GPIO_ACTIVE_HIGH>; +- #address-cells = <1>; +- #size-cells = <0>; +- +- /* Right-side USB Type-C port */ +- connector@0 { +- compatible = "usb-c-connector"; +- reg = <0>; +- power-role = "dual"; +- data-role = "dual"; +- +- ports { +- #address-cells = <1>; +- #size-cells = <0>; +- +- port@0 { +- reg = <0>; +- +- pmic_glink_ss0_hs_in: endpoint { +- remote-endpoint = <&usb_1_ss0_dwc3_hs>; +- }; +- }; +- +- port@1 { +- reg = <1>; +- +- pmic_glink_ss0_ss_in: endpoint { +- remote-endpoint = <&usb_1_ss0_qmpphy_out>; +- }; +- }; +- }; +- }; +- +- /* Left-side USB Type-C port */ +- connector@1 { +- compatible = "usb-c-connector"; +- reg = <1>; +- power-role = "dual"; +- data-role = "dual"; +- +- ports { +- #address-cells = <1>; +- #size-cells = <0>; +- +- port@0 { +- reg = <0>; +- +- pmic_glink_ss1_hs_in: endpoint { +- remote-endpoint = <&usb_1_ss1_dwc3_hs>; +- }; +- }; +- +- port@1 { +- reg = <1>; +- +- pmic_glink_ss1_ss_in: endpoint { +- remote-endpoint = <&usb_1_ss1_qmpphy_out>; +- }; +- }; +- }; +- }; +- }; +- +- reserved-memory { +- linux,cma { +- compatible = "shared-dma-pool"; +- size = <0x0 0x8000000>; +- reusable; +- linux,cma-default; +- }; +- }; +- +- vreg_edp_3p3: regulator-edp-3p3 { +- compatible = "regulator-fixed"; +- +- regulator-name = "VREG_EDP_3P3"; +- regulator-min-microvolt = <3300000>; +- regulator-max-microvolt = <3300000>; +- +- gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; +- enable-active-high; +- +- pinctrl-0 = <&edp_reg_en>; +- pinctrl-names = "default"; +- +- regulator-boot-on; +- }; +- +- vreg_nvme: regulator-nvme { +- compatible = "regulator-fixed"; +- +- regulator-name = "VREG_NVME_3P3"; +- regulator-min-microvolt = <3300000>; +- regulator-max-microvolt = <3300000>; +- +- gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; +- enable-active-high; +- +- pinctrl-0 = <&nvme_reg_en>; +- pinctrl-names = "default"; +- }; +- +- vreg_vph_pwr: regulator-vph-pwr { +- compatible = "regulator-fixed"; +- +- regulator-name = "vph_pwr"; +- regulator-min-microvolt = <3700000>; +- regulator-max-microvolt = <3700000>; +- +- regulator-always-on; +- regulator-boot-on; +- }; +-}; +- +-&apps_rsc { +- regulators-0 { +- compatible = "qcom,pm8550-rpmh-regulators"; +- qcom,pmic-id = "b"; +- vdd-bob1-supply = <&vreg_vph_pwr>; +- vdd-bob2-supply = <&vreg_vph_pwr>; +- vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; +- vdd-l2-l13-l14-supply = <&vreg_bob1>; +- vdd-l5-l16-supply = <&vreg_bob1>; +- vdd-l6-l7-supply = <&vreg_bob2>; +- vdd-l8-l9-supply = <&vreg_bob1>; +- vdd-l12-supply = <&vreg_s5j_1p2>; +- vdd-l15-supply = <&vreg_s4c_1p8>; +- vdd-l17-supply = <&vreg_bob2>; +- +- vreg_bob1: bob1 { +- regulator-name = "vreg_bob1"; +- regulator-min-microvolt = <3008000>; +- regulator-max-microvolt = <3960000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_bob2: bob2 { +- regulator-name = "vreg_bob2"; +- regulator-min-microvolt = <2504000>; +- regulator-max-microvolt = <3008000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l2b_3p0: ldo2 { +- regulator-name = "vreg_l2b_3p0"; +- regulator-min-microvolt = <3072000>; +- regulator-max-microvolt = <3072000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l4b_1p8: ldo4 { +- regulator-name = "vreg_l4b_1p8"; +- regulator-min-microvolt = <1800000>; +- regulator-max-microvolt = <1800000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l6b_1p8: ldo6 { +- regulator-name = "vreg_l6b_1p8"; +- regulator-min-microvolt = <1800000>; +- regulator-max-microvolt = <2960000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l8b_3p0: ldo8 { +- regulator-name = "vreg_l8b_3p0"; +- regulator-min-microvolt = <3072000>; +- regulator-max-microvolt = <3072000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l9b_2p9: ldo9 { +- regulator-name = "vreg_l9b_2p9"; +- regulator-min-microvolt = <2960000>; +- regulator-max-microvolt = <2960000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l12b_1p2: ldo12 { +- regulator-name = "vreg_l12b_1p2"; +- regulator-min-microvolt = <1200000>; +- regulator-max-microvolt = <1200000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l13b_3p0: ldo13 { +- regulator-name = "vreg_l13b_3p0"; +- regulator-min-microvolt = <3072000>; +- regulator-max-microvolt = <3072000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l14b_3p0: ldo14 { +- regulator-name = "vreg_l14b_3p0"; +- regulator-min-microvolt = <3072000>; +- regulator-max-microvolt = <3072000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l15b_1p8: ldo15 { +- regulator-name = "vreg_l15b_1p8"; +- regulator-min-microvolt = <1800000>; +- regulator-max-microvolt = <1800000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l17b_2p5: ldo17 { +- regulator-name = "vreg_l17b_2p5"; +- regulator-min-microvolt = <2504000>; +- regulator-max-microvolt = <2504000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- }; +- +- regulators-1 { +- compatible = "qcom,pm8550ve-rpmh-regulators"; +- qcom,pmic-id = "c"; +- vdd-l1-supply = <&vreg_s5j_1p2>; +- vdd-l2-supply = <&vreg_s1f_0p7>; +- vdd-l3-supply = <&vreg_s1f_0p7>; +- +- vreg_s4c_1p8: smps4 { +- regulator-name = "vreg_s4c_1p8"; +- regulator-min-microvolt = <1856000>; +- regulator-max-microvolt = <2000000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l1c_1p2: ldo1 { +- regulator-name = "vreg_l1c_1p2"; +- regulator-min-microvolt = <1200000>; +- regulator-max-microvolt = <1200000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l2c_0p8: ldo2 { +- regulator-name = "vreg_l2c_0p8"; +- regulator-min-microvolt = <880000>; +- regulator-max-microvolt = <880000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l3c_0p9: ldo3 { +- regulator-name = "vreg_l3c_0p9"; +- regulator-min-microvolt = <920000>; +- regulator-max-microvolt = <920000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- }; +- +- regulators-2 { +- compatible = "qcom,pmc8380-rpmh-regulators"; +- qcom,pmic-id = "d"; +- vdd-l1-supply = <&vreg_s1f_0p7>; +- vdd-l2-supply = <&vreg_s1f_0p7>; +- vdd-l3-supply = <&vreg_s4c_1p8>; +- vdd-s1-supply = <&vreg_vph_pwr>; +- +- vreg_l1d_0p8: ldo1 { +- regulator-name = "vreg_l1d_0p8"; +- regulator-min-microvolt = <880000>; +- regulator-max-microvolt = <880000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l2d_0p9: ldo2 { +- regulator-name = "vreg_l2d_0p9"; +- regulator-min-microvolt = <912000>; +- regulator-max-microvolt = <912000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l3d_1p8: ldo3 { +- regulator-name = "vreg_l3d_1p8"; +- regulator-min-microvolt = <1800000>; +- regulator-max-microvolt = <1800000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- }; +- +- regulators-3 { +- compatible = "qcom,pmc8380-rpmh-regulators"; +- qcom,pmic-id = "e"; +- vdd-l2-supply = <&vreg_s1f_0p7>; +- vdd-l3-supply = <&vreg_s5j_1p2>; +- +- vreg_l2e_0p8: ldo2 { +- regulator-name = "vreg_l2e_0p8"; +- regulator-min-microvolt = <880000>; +- regulator-max-microvolt = <880000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l3e_1p2: ldo3 { +- regulator-name = "vreg_l3e_1p2"; +- regulator-min-microvolt = <1200000>; +- regulator-max-microvolt = <1200000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- }; +- +- regulators-4 { +- compatible = "qcom,pmc8380-rpmh-regulators"; +- qcom,pmic-id = "f"; +- vdd-l1-supply = <&vreg_s5j_1p2>; +- vdd-l2-supply = <&vreg_s5j_1p2>; +- vdd-l3-supply = <&vreg_s5j_1p2>; +- vdd-s1-supply = <&vreg_vph_pwr>; +- +- vreg_s1f_0p7: smps1 { +- regulator-name = "vreg_s1f_0p7"; +- regulator-min-microvolt = <700000>; +- regulator-max-microvolt = <1100000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- }; +- +- regulators-6 { +- compatible = "qcom,pm8550ve-rpmh-regulators"; +- qcom,pmic-id = "i"; +- vdd-l1-supply = <&vreg_s4c_1p8>; +- vdd-l2-supply = <&vreg_s5j_1p2>; +- vdd-l3-supply = <&vreg_s1f_0p7>; +- vdd-s1-supply = <&vreg_vph_pwr>; +- vdd-s2-supply = <&vreg_vph_pwr>; +- +- vreg_s1i_0p9: smps1 { +- regulator-name = "vreg_s1i_0p9"; +- regulator-min-microvolt = <900000>; +- regulator-max-microvolt = <920000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_s2i_1p0: smps2 { +- regulator-name = "vreg_s2i_1p0"; +- regulator-min-microvolt = <1000000>; +- regulator-max-microvolt = <1100000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l1i_1p8: ldo1 { +- regulator-name = "vreg_l1i_1p8"; +- regulator-min-microvolt = <1800000>; +- regulator-max-microvolt = <1800000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l2i_1p2: ldo2 { +- regulator-name = "vreg_l2i_1p2"; +- regulator-min-microvolt = <1200000>; +- regulator-max-microvolt = <1200000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l3i_0p8: ldo3 { +- regulator-name = "vreg_l3i_0p8"; +- regulator-min-microvolt = <880000>; +- regulator-max-microvolt = <880000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- }; +- +- regulators-7 { +- compatible = "qcom,pm8550ve-rpmh-regulators"; +- qcom,pmic-id = "j"; +- vdd-l1-supply = <&vreg_s1f_0p7>; +- vdd-l2-supply = <&vreg_s5j_1p2>; +- vdd-l3-supply = <&vreg_s1f_0p7>; +- vdd-s5-supply = <&vreg_vph_pwr>; +- +- vreg_s5j_1p2: smps5 { +- regulator-name = "vreg_s5j_1p2"; +- regulator-min-microvolt = <1256000>; +- regulator-max-microvolt = <1304000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l1j_0p9: ldo1 { +- regulator-name = "vreg_l1j_0p9"; +- regulator-min-microvolt = <912000>; +- regulator-max-microvolt = <912000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l2j_1p2: ldo2 { +- regulator-name = "vreg_l2j_1p2"; +- regulator-min-microvolt = <1256000>; +- regulator-max-microvolt = <1256000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- +- vreg_l3j_0p8: ldo3 { +- regulator-name = "vreg_l3j_0p8"; +- regulator-min-microvolt = <880000>; +- regulator-max-microvolt = <880000>; +- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; +- }; +- }; +-}; +- +-&gpu { +- status = "okay"; +- +- zap-shader { +- firmware-name = "qcom/x1e80100/dell/tributo/qcdxkmsuc8380.mbn"; +- }; +-}; +- +-&i2c0 { +- clock-frequency = <400000>; +- status = "okay"; +- +- keyboard@5 { +- compatible = "hid-over-i2c"; +- reg = <0x5>; +- +- hid-descr-addr = <0x20>; +- interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>; +- +- pinctrl-0 = <&kybd_default>; +- pinctrl-names = "default"; +- +- wakeup-source; +- }; +-}; +- +-&i2c3 { +- clock-frequency = <400000>; +- status = "disabled"; +- /* PS8830 Retimer @0x8 */ +- /* Unknown device @0x9 */ +-}; +- +-&i2c5 { +- clock-frequency = <100000>; +- status = "disabled"; +- /* Unknown device @0x3b */ +-}; +- +-&i2c7 { +- clock-frequency = <400000>; +- status = "disabled"; +- /* PS8830 Retimer @0x8 */ +- /* Unknown device @0x9 */ +-}; +- +-&i2c8 { +- clock-frequency = <400000>; +- +- status = "okay"; +- +- touchscreen@0 { +- compatible = "hid-over-i2c"; +- reg = <0x0>; +- +- hid-descr-addr = <0x1>; +- interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; +- +- pinctrl-0 = <&ts0_default>; +- pinctrl-names = "default"; +- }; +-}; +- +-&i2c9 { +- clock-frequency = <400000>; +- status = "disabled"; +- /* USB3 retimer device @0x4f */ }; +- +-&i2c17 { +- clock-frequency = <400000>; +- status = "okay"; +- +- touchpad@2c { +- compatible = "hid-over-i2c"; +- reg = <0x2c>; +- +- hid-descr-addr = <0x20>; +- interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>; +- +- pinctrl-0 = <&tpad_default>; +- pinctrl-names = "default"; +- +- wakeup-source; +- }; +-}; +- +-&mdss { +- status = "okay"; +-}; +- +-&mdss_dp3 { +- compatible = "qcom,x1e80100-dp"; +- /delete-property/ #sound-dai-cells; +- +- status = "okay"; +- +- aux-bus { +- panel { +- /* 1920x1200 IPS panel is SHP1593, PNP09FF compatible */ +- compatible = "edp-panel"; +- power-supply = <&vreg_edp_3p3>; +- +- port { +- edp_panel_in: endpoint { +- remote-endpoint = <&mdss_dp3_out>; +- }; +- }; +- }; +- }; +- +- ports { +- port@1 { +- reg = <1>; +- +- mdss_dp3_out: endpoint { +- data-lanes = <0 1 2 3>; +- link-frequencies = /bits/ 64 +- <1620000000 2700000000 5400000000 8100000000>; +- +- remote-endpoint = <&edp_panel_in>; +- }; +- }; +- }; +-}; +- +-&mdss_dp3_phy { +- vdda-phy-supply = <&vreg_l3j_0p8>; +- vdda-pll-supply = <&vreg_l2j_1p2>; +- +- status = "okay"; +-}; +- +-&pcie4 { +- perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; +- wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; +- +- pinctrl-0 = <&pcie4_default>; +- pinctrl-names = "default"; +- +- status = "okay"; +-}; +- +-&pcie4_phy { +- vdda-phy-supply = <&vreg_l3i_0p8>; +- vdda-pll-supply = <&vreg_l3e_1p2>; +- +- status = "okay"; +-}; +- +-&pcie6a { +- perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; +- wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; +- +- vddpe-3v3-supply = <&vreg_nvme>; +- +- pinctrl-0 = <&pcie6a_default>; +- pinctrl-names = "default"; +- +- status = "okay"; +-}; +- +-&pcie6a_phy { +- vdda-phy-supply = <&vreg_l1d_0p8>; +- vdda-pll-supply = <&vreg_l2j_1p2>; +- +- status = "okay"; +-}; +- +-&qupv3_0 { +- status = "okay"; +-}; +- +-&qupv3_1 { +- status = "okay"; +-}; +- +-&qupv3_2 { +- status = "okay"; +-}; +- +-&remoteproc_adsp { +- firmware-name = "qcom/x1e80100/dell/tributo/qcadsp8380.mbn", +- "qcom/x1e80100/dell/tributo/adsp_dtbs.elf"; +- +- status = "okay"; +-}; +- +-&remoteproc_cdsp { +- firmware-name = "qcom/x1e80100/dell/tributo/qccdsp8380.mbn", +- "qcom/x1e80100/dell/tributo/cdsp_dtbs.elf"; +- +- status = "okay"; +-}; +- +-&smb2360_0_eusb2_repeater { +- vdd18-supply = <&vreg_l3d_1p8>; +- vdd3-supply = <&vreg_l2b_3p0>; }; +- +-&smb2360_1_eusb2_repeater { +- vdd18-supply = <&vreg_l3d_1p8>; +- vdd3-supply = <&vreg_l14b_3p0>; }; +- +-&tlmm { +- gpio-reserved-ranges = <44 4>, /* SPI11 (TPM) */ +- <76 4>, /* SPI19 (TZ Protected) */ +- <238 1>; /* UFS Reset */ +- +- cam_indicator_en: cam-indicator-en-state { +- pins = "gpio110"; +- function = "gpio"; +- drive-strength = <2>; +- bias-disable; +- }; +- +- edp_reg_en: edp-reg-en-state { +- pins = "gpio70"; +- function = "gpio"; +- drive-strength = <16>; +- bias-disable; +- }; +- +- hall_int_n_default: hall-int-n-state { +- pins = "gpio92"; +- function = "gpio"; +- +- bias-disable; +- }; +- +- kybd_default: kybd-default-state { +- pins = "gpio67"; +- function = "gpio"; +- bias-pull-up; +- }; +- +- nvme_reg_en: nvme-reg-en-state { +- pins = "gpio18"; +- function = "gpio"; +- drive-strength = <2>; +- bias-disable; +- }; +- +- pcie4_default: pcie4-default-state { +- clkreq-n-pins { +- pins = "gpio147"; +- function = "pcie4_clk"; +- drive-strength = <2>; +- bias-pull-up; +- }; +- +- perst-n-pins { +- pins = "gpio146"; +- function = "gpio"; +- drive-strength = <2>; +- bias-disable; +- }; +- +- wake-n-pins { +- pins = "gpio148"; +- function = "gpio"; +- drive-strength = <2>; +- bias-pull-up; +- }; +- }; +- +- pcie6a_default: pcie6a-default-state { +- clkreq-n-pins { +- pins = "gpio153"; +- function = "pcie6a_clk"; +- drive-strength = <2>; +- bias-pull-up; +- }; +- +- perst-n-pins { +- pins = "gpio152"; +- function = "gpio"; +- drive-strength = <2>; +- bias-disable; +- }; +- +- wake-n-pins { +- pins = "gpio154"; +- function = "gpio"; +- drive-strength = <2>; +- bias-pull-up; +- }; +- }; +- +- tpad_default: tpad-default-state { +- disable-pins { +- pins = "gpio38"; +- function = "gpio"; +- output-high; +- }; +- +- int-n-pins { +- pins = "gpio3"; +- function = "gpio"; +- bias-pull-up; +- }; +- +- reset-n-pins { +- pins = "gpio52"; +- function = "gpio"; +- bias-disable; +- }; +- }; +- +- ts0_default: ts0-default-state { +- disable-pins { +- pins = "gpio75"; +- function = "gpio"; +- output-high; +- }; +- +- int-n-pins { +- pins = "gpio51"; +- function = "gpio"; +- bias-pull-up; +- }; +- +- reset-n-pins { +- /* Technically should be High-Z input */ +- pins = "gpio48"; +- function = "gpio"; +- output-low; +- drive-strength = <2>; +- }; +- }; +-}; +- +-&uart21 { +- compatible = "qcom,geni-debug-uart"; +- status = "okay"; +-}; +- +-&usb_1_ss0_hsphy { +- vdd-supply = <&vreg_l3j_0p8>; +- vdda12-supply = <&vreg_l2j_1p2>; +- +- phys = <&smb2360_0_eusb2_repeater>; +- +- status = "okay"; +-}; +- +-&usb_1_ss0_qmpphy { +- vdda-phy-supply = <&vreg_l3e_1p2>; +- vdda-pll-supply = <&vreg_l1j_0p9>; +- +- status = "okay"; +-}; +- +-&usb_1_ss0 { +- status = "okay"; +-}; +- +-&usb_1_ss0_dwc3 { +- dr_mode = "host"; +-}; +- +-&usb_1_ss0_dwc3_hs { +- remote-endpoint = <&pmic_glink_ss0_hs_in>; }; +- +-&usb_1_ss0_qmpphy_out { +- remote-endpoint = <&pmic_glink_ss0_ss_in>; }; +- +-&usb_1_ss1_hsphy { +- vdd-supply = <&vreg_l3j_0p8>; +- vdda12-supply = <&vreg_l2j_1p2>; +- +- phys = <&smb2360_1_eusb2_repeater>; +- +- status = "okay"; +-}; +- +-&usb_1_ss1_qmpphy { +- vdda-phy-supply = <&vreg_l3e_1p2>; +- vdda-pll-supply = <&vreg_l2d_0p9>; +- +- status = "okay"; +-}; +- +-&usb_1_ss1 { +- status = "okay"; +-}; +- +-&usb_1_ss1_dwc3 { +- dr_mode = "host"; +-}; +- +-&usb_1_ss1_dwc3_hs { +- remote-endpoint = <&pmic_glink_ss1_hs_in>; }; +- +-&usb_1_ss1_qmpphy_out { +- remote-endpoint = <&pmic_glink_ss1_ss_in>; };
Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
Quoted 3 lines · Bryan
Fascinating topic. First of all, thank you Alex for the explanation of your logic, and thank you as well for the work on the device tree for the XPS 13. I understand completely how the Dell naming/numbering scheme is confusing. The shortened version down to just the model number could also be confusing. For example, there is an XPS 9520 as well as a Latitude 9520. The 9 basically translates to "premium" not a specific line of business. For what it is worth, I would prefer the dell-xps13-9345 naming and I think we can have to be mindful to avoid a naming collision in a decade.
Hi,
Thanks for the input, it's really nice to have Dell's perspective as well. That's a good point with latitude, I was only aware of 5XXX/7XXX naming for that one... which I guess further highlights the confusing naming scheme.
I will re-spin with dell-xps13-9345 and dell,xps13-9345 respectively as proposed then, unless there will be any other feedback on the V3 series before tomorrow.
Thanks,
Alex
Quoted 961 lines
Thanks again for the support.
Bryan Kemp
Architect - Linux OS EngineeringInternal Use - Confidential
-----Original Message-----
From: Aleksandrs Vinarskis <[email protected]>
Sent: Monday, September 30, 2024 2:24 PM
To: Laurentiu Tudor <[email protected]>
Cc: Bjorn Andersson <[email protected]>; Krzysztof Kozlowski <[email protected]>; Dmitry Baryshkov <[email protected]>; [email protected]; [email protected]; [email protected]; Tudor, Laurentiu <[email protected]>; Konrad Dybcio <[email protected]>; Rob Herring <[email protected]>; Krzysztof Kozlowski <[email protected]>; Conor Dooley <[email protected]>; Rob Clark <[email protected]>; Peter de Kraker <[email protected]>; Kemp, Bryan <[email protected]>
Subject: Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345[EXTERNAL EMAIL]
Quoted 37 lines · Laurentiu Tudor
Hi Alex,
Thanks for this! Comment inline.
Quoted 21 lines · Aleksandrs Vinarskis
Initial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resumeNot working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery InfoQuoted 8 lines
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panels
* TouchscreenSigned-off-by Aleksandrs Vinarskis <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 1 + .../dts/qcom/x1e80100-dell-tributo-13.dts | 860 ++++++++++++++++++Quoted 4 lines
Could you please use the marketing name for the device tree file name & machine compatible, e.g. "
x1e80100-dell-xps13-9345.dts" for the dts file and "dell,xps13-9345" for the compat? I'm thinking that this will help people to identify it more easily.Hi,
Even though I agree that it may be easier to identify for a non-developer, I am a bit skeptical as Dell has a pretty weird naming convention which sometimes results in the name being non-unique.
In particular case - 9345 - 9 stands for XPS series, 3 stands for 13", and 45 would typically be the last digit of year + 0 (so 40), but with the introduction of last year's ''13 Plus"series they added a 5. At present, this is unique, however in 10 years it may not be.I have recently hit this issue when working on Dell XPS 15" 2024 (9530), which has the same model number as Dell XPS 15" 2013 and led to huge confusions. Only way to distinguish them is by codename ('fiorano' for the newer one), or using a complete name including the year... The codename on the other hand is easily searchable both in the source code and online.
I tried to browse the source code for existing notation, but didn't find anything strongly supporting one or another way, so decided to follow Microsoft Surface's example with codenames ('romulus').
Codenaming is also imperfect though, as in Dell's case it typically refers to chassis, rather than _the_ particular device, which typically lasts several years. Typically throughout chassis generation internals stay +/- the same, but we can't know if any of the changes would be breaking. Perhaps then,x1e80100-dell-tributo-9345anddell,tributo-9345respectively, as this would be the shortest yet most complete description? 'Tributo' already implies its XPS 13" and chassis variation (touchar, hidden trackpad etc etc), '9345' implies XPS 13" of 2024 (?) and in combination with chassis variant pinpoints the model. Otherwise, if it's strongly desired to use marketing names it can be reduced down tox1e80100-dell-9345.dtsanddell,9345altogether as
9345 implies it being both 'XPS' series and 13", and we can hope that by 2034 Dell won't repeat the same mistake with naming. Curious to hear maintainers' opinions as well.
P.S. I've sent the V3 version of the series, it probably makes sense to move this conversation there for visibility.Alex
Quoted 884 lines
---
Thanks & Best Regards, LaurentiuQuoted 879 lines
2 files changed, 861 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dtsarch/arm64/boot/dts/qcom/Makefile +1
-0@@ -271,6 +271,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e78100-lenovo-thinkpad-t14s.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-asus-vivobook-s15.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb +dtb-$(CONFIG_ARCH_QCOM) += x1e80100-dell-tributo-13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-lenovo-yoga-slim7x.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus15.dtbarch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts new file +853
-0@@ -0,0 +1,860 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + * Copyright (c) 2024 Aleksandrs Vinarskis +<[email protected]> */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> #include +<dt-bindings/input/input.h> #include <dt-bindings/leds/common.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +#include "x1e80100.dtsi" +#include "x1e80100-pmics.dtsi" + +/ { + model = "Dell XPS 13 9345"; + compatible = "dell,tributo-13", "qcom,x1e80100"; + chassis-type = "laptop"; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&hall_int_n_default>; + pinctrl-names = "default"; + + switch-lid { + gpios = <&tlmm 92 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + wakeup-source; + wakeup-event-action = <EV_ACT_DEASSERTED>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&cam_indicator_en>; + + led-camera-indicator { + label = "white:camera-indicator"; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_WHITE>; + gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + /* Reuse as a panic indicator until we get a "camera on" trigger */ + panic-indicator; + }; + }; + + pmic-glink { + compatible = "qcom,x1e80100-pmic-glink", + "qcom,sm8550-pmic-glink", + "qcom,pmic-glink"; + orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, + <&tlmm 123 GPIO_ACTIVE_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + /* Right-side USB Type-C port */ + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss0_hs_in: endpoint { + remote-endpoint = <&usb_1_ss0_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss0_ss_in: endpoint { + remote-endpoint = <&usb_1_ss0_qmpphy_out>; + }; + }; + }; + }; + + /* Left-side USB Type-C port */ + connector@1 { + compatible = "usb-c-connector"; + reg = <1>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss1_hs_in: endpoint { + remote-endpoint = <&usb_1_ss1_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss1_ss_in: endpoint { + remote-endpoint = <&usb_1_ss1_qmpphy_out>; + }; + }; + }; + }; + }; + + reserved-memory { + linux,cma { + compatible = "shared-dma-pool"; + size = <0x0 0x8000000>; + reusable; + linux,cma-default; + }; + }; + + vreg_edp_3p3: regulator-edp-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_EDP_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&edp_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_nvme: regulator-nvme { + compatible = "regulator-fixed"; + + regulator-name = "VREG_NVME_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&nvme_reg_en>; + pinctrl-names = "default"; + }; + + vreg_vph_pwr: regulator-vph-pwr { + compatible = "regulator-fixed"; + + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8550-rpmh-regulators"; + qcom,pmic-id = "b"; + vdd-bob1-supply = <&vreg_vph_pwr>; + vdd-bob2-supply = <&vreg_vph_pwr>; + vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; + vdd-l2-l13-l14-supply = <&vreg_bob1>; + vdd-l5-l16-supply = <&vreg_bob1>; + vdd-l6-l7-supply = <&vreg_bob2>; + vdd-l8-l9-supply = <&vreg_bob1>; + vdd-l12-supply = <&vreg_s5j_1p2>; + vdd-l15-supply = <&vreg_s4c_1p8>; + vdd-l17-supply = <&vreg_bob2>; + + vreg_bob1: bob1 { + regulator-name = "vreg_bob1"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob2: bob2 { + regulator-name = "vreg_bob2"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-name = "vreg_l2b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4b_1p8: ldo4 { + regulator-name = "vreg_l4b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p8: ldo6 { + regulator-name = "vreg_l6b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8b_3p0: ldo8 { + regulator-name = "vreg_l8b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_2p9: ldo9 { + regulator-name = "vreg_l9b_2p9"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12b_1p2: ldo12 { + regulator-name = "vreg_l12b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13b_3p0: ldo13 { + regulator-name = "vreg_l13b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14b_3p0: ldo14 { + regulator-name = "vreg_l14b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15b_1p8: ldo15 { + regulator-name = "vreg_l15b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17b_2p5: ldo17 { + regulator-name = "vreg_l17b_2p5"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "c"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s1f_0p7>; + + vreg_s4c_1p8: smps4 { + regulator-name = "vreg_s4c_1p8"; + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1c_1p2: ldo1 { + regulator-name = "vreg_l1c_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c_0p8: ldo2 { + regulator-name = "vreg_l2c_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c_0p9: ldo3 { + regulator-name = "vreg_l3c_0p9"; + regulator-min-microvolt = <920000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "d"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s4c_1p8>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_l1d_0p8: ldo1 { + regulator-name = "vreg_l1d_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2d_0p9: ldo2 { + regulator-name = "vreg_l2d_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3d_1p8: ldo3 { + regulator-name = "vreg_l3d_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-3 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "e"; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s5j_1p2>; + + vreg_l2e_0p8: ldo2 { + regulator-name = "vreg_l2e_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3e_1p2: ldo3 { + regulator-name = "vreg_l3e_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-4 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "f"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s5j_1p2>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_s1f_0p7: smps1 { + regulator-name = "vreg_s1f_0p7"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-6 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "i"; + vdd-l1-supply = <&vreg_s4c_1p8>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s1-supply = <&vreg_vph_pwr>; + vdd-s2-supply = <&vreg_vph_pwr>; + + vreg_s1i_0p9: smps1 { + regulator-name = "vreg_s1i_0p9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s2i_1p0: smps2 { + regulator-name = "vreg_s2i_1p0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1i_1p8: ldo1 { + regulator-name = "vreg_l1i_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2i_1p2: ldo2 { + regulator-name = "vreg_l2i_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3i_0p8: ldo3 { + regulator-name = "vreg_l3i_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-7 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "j"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s5-supply = <&vreg_vph_pwr>; + + vreg_s5j_1p2: smps5 { + regulator-name = "vreg_s5j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1j_0p9: ldo1 { + regulator-name = "vreg_l1j_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2j_1p2: ldo2 { + regulator-name = "vreg_l2j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3j_0p8: ldo3 { + regulator-name = "vreg_l3j_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&gpu { + status = "okay"; + + zap-shader { + firmware-name = "qcom/x1e80100/dell/tributo/qcdxkmsuc8380.mbn"; + }; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + keyboard@5 { + compatible = "hid-over-i2c"; + reg = <0x5>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&kybd_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c5 { + clock-frequency = <100000>; + status = "disabled"; + /* Unknown device @0x3b */ +}; + +&i2c7 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c8 { + clock-frequency = <400000>; + + status = "okay"; + + touchscreen@0 { + compatible = "hid-over-i2c"; + reg = <0x0>; + + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&ts0_default>; + pinctrl-names = "default"; + }; +}; + +&i2c9 { + clock-frequency = <400000>; + status = "disabled"; + /* USB3 retimer device @0x4f */ }; + +&i2c17 { + clock-frequency = <400000>; + status = "okay"; + + touchpad@2c { + compatible = "hid-over-i2c"; + reg = <0x2c>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&tpad_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp3 { + compatible = "qcom,x1e80100-dp"; + /delete-property/ #sound-dai-cells; + + status = "okay"; + + aux-bus { + panel { + /* 1920x1200 IPS panel is SHP1593, PNP09FF compatible */ + compatible = "edp-panel"; + power-supply = <&vreg_edp_3p3>; + + port { + edp_panel_in: endpoint { + remote-endpoint = <&mdss_dp3_out>; + }; + }; + }; + }; + + ports { + port@1 { + reg = <1>; + + mdss_dp3_out: endpoint { + data-lanes = <0 1 2 3>; + link-frequencies = /bits/ 64 + <1620000000 2700000000 5400000000 8100000000>; + + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +}; + +&mdss_dp3_phy { + vdda-phy-supply = <&vreg_l3j_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&pcie4 { + perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&pcie4_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie4_phy { + vdda-phy-supply = <&vreg_l3i_0p8>; + vdda-pll-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&pcie6a { + perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; + + vddpe-3v3-supply = <&vreg_nvme>; + + pinctrl-0 = <&pcie6a_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie6a_phy { + vdda-phy-supply = <&vreg_l1d_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&qupv3_0 { + status = "okay"; +}; + +&qupv3_1 { + status = "okay"; +}; + +&qupv3_2 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/x1e80100/dell/tributo/qcadsp8380.mbn", + "qcom/x1e80100/dell/tributo/adsp_dtbs.elf"; + + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/x1e80100/dell/tributo/qccdsp8380.mbn", + "qcom/x1e80100/dell/tributo/cdsp_dtbs.elf"; + + status = "okay"; +}; + +&smb2360_0_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l2b_3p0>; }; + +&smb2360_1_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l14b_3p0>; }; + +&tlmm { + gpio-reserved-ranges = <44 4>, /* SPI11 (TPM) */ + <76 4>, /* SPI19 (TZ Protected) */ + <238 1>; /* UFS Reset */ + + cam_indicator_en: cam-indicator-en-state { + pins = "gpio110"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + edp_reg_en: edp-reg-en-state { + pins = "gpio70"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + hall_int_n_default: hall-int-n-state { + pins = "gpio92"; + function = "gpio"; + + bias-disable; + }; + + kybd_default: kybd-default-state { + pins = "gpio67"; + function = "gpio"; + bias-pull-up; + }; + + nvme_reg_en: nvme-reg-en-state { + pins = "gpio18"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + pcie4_default: pcie4-default-state { + clkreq-n-pins { + pins = "gpio147"; + function = "pcie4_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio146"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio148"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie6a_default: pcie6a-default-state { + clkreq-n-pins { + pins = "gpio153"; + function = "pcie6a_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio152"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio154"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + tpad_default: tpad-default-state { + disable-pins { + pins = "gpio38"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio3"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + pins = "gpio52"; + function = "gpio"; + bias-disable; + }; + }; + + ts0_default: ts0-default-state { + disable-pins { + pins = "gpio75"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio51"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + /* Technically should be High-Z input */ + pins = "gpio48"; + function = "gpio"; + output-low; + drive-strength = <2>; + }; + }; +}; + +&uart21 { + compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; + +&usb_1_ss0_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_0_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss0_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l1j_0p9>; + + status = "okay"; +}; + +&usb_1_ss0 { + status = "okay"; +}; + +&usb_1_ss0_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss0_dwc3_hs { + remote-endpoint = <&pmic_glink_ss0_hs_in>; }; + +&usb_1_ss0_qmpphy_out { + remote-endpoint = <&pmic_glink_ss0_ss_in>; }; + +&usb_1_ss1_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_1_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss1_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l2d_0p9>; + + status = "okay"; +}; + +&usb_1_ss1 { + status = "okay"; +}; + +&usb_1_ss1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss1_dwc3_hs { + remote-endpoint = <&pmic_glink_ss1_hs_in>; }; + +&usb_1_ss1_qmpphy_out { + remote-endpoint = <&pmic_glink_ss1_ss_in>; };
Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
Hi Alex,
Quoted 11 lines · Aleksandrs Vinarskis
Quoted 3 lines · Bryan
Fascinating topic. First of all, thank you Alex for the explanation of your logic, and thank you as well for the work on the device tree for the XPS 13. I understand completely how the Dell naming/numbering scheme is confusing. The shortened version down to just the model number could also be confusing. For example, there is an XPS 9520 as well as a Latitude 9520. The 9 basically translates to "premium" not a specific line of business. For what it is worth, I would prefer the dell-xps13-9345 naming and I think we can have to be mindful to avoid a naming collision in a decade.
Hi,
Thanks for the input, it's really nice to have Dell's perspective as well. That's a good point with latitude, I was only aware of 5XXX/7XXX naming for that one... which I guess further highlights the confusing naming scheme.
Yeah, completely agree. We will raise this internally so that in the future we'll do a better job at naming platforms.
Quoted 3 lines
I will re-spin with
dell-xps13-9345anddell,xps13-9345respectively as proposed then, unless there will be any other feedback on the V3 series before tomorrow.
Great, thanks!
Couple of points:
- i'm thinking that maybe at a later point, as more dell platforms are
getting added, we can re-organize the device trees, e.g. have a common 'dell-xps.dtsi' which gets inherited by specific platforms
- just noticed that the firmware paths point to something like
".../dell/tributo/...". Should we reconsider these too? Maybe something like ".../dell/xps/..." would be better?
---
Thanks & Best Regards, Laurentiu
Quoted 964 lines
Thanks,
AlexQuoted 961 lines
Thanks again for the support.
Bryan Kemp
Architect - Linux OS EngineeringInternal Use - Confidential
-----Original Message-----
From: Aleksandrs Vinarskis <[email protected]>
Sent: Monday, September 30, 2024 2:24 PM
To: Laurentiu Tudor <[email protected]>
Cc: Bjorn Andersson <[email protected]>; Krzysztof Kozlowski <[email protected]>; Dmitry Baryshkov <[email protected]>; [email protected]; [email protected]; [email protected]; Tudor, Laurentiu <[email protected]>; Konrad Dybcio <[email protected]>; Rob Herring <[email protected]>; Krzysztof Kozlowski <[email protected]>; Conor Dooley <[email protected]>; Rob Clark <[email protected]>; Peter de Kraker <[email protected]>; Kemp, Bryan <[email protected]>
Subject: Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345[EXTERNAL EMAIL]
Quoted 37 lines · Laurentiu Tudor
Hi Alex,
Thanks for this! Comment inline.
Quoted 21 lines · Aleksandrs Vinarskis
Initial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resumeNot working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery InfoQuoted 8 lines
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panels
* TouchscreenSigned-off-by Aleksandrs Vinarskis <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 1 + .../dts/qcom/x1e80100-dell-tributo-13.dts | 860 ++++++++++++++++++Quoted 4 lines
Could you please use the marketing name for the device tree file name & machine compatible, e.g. "
x1e80100-dell-xps13-9345.dts" for the dts file and "dell,xps13-9345" for the compat? I'm thinking that this will help people to identify it more easily.Hi,
Even though I agree that it may be easier to identify for a non-developer, I am a bit skeptical as Dell has a pretty weird naming convention which sometimes results in the name being non-unique.
In particular case - 9345 - 9 stands for XPS series, 3 stands for 13", and 45 would typically be the last digit of year + 0 (so 40), but with the introduction of last year's ''13 Plus"series they added a 5. At present, this is unique, however in 10 years it may not be.I have recently hit this issue when working on Dell XPS 15" 2024 (9530), which has the same model number as Dell XPS 15" 2013 and led to huge confusions. Only way to distinguish them is by codename ('fiorano' for the newer one), or using a complete name including the year... The codename on the other hand is easily searchable both in the source code and online.
I tried to browse the source code for existing notation, but didn't find anything strongly supporting one or another way, so decided to follow Microsoft Surface's example with codenames ('romulus').
Codenaming is also imperfect though, as in Dell's case it typically refers to chassis, rather than _the_ particular device, which typically lasts several years. Typically throughout chassis generation internals stay +/- the same, but we can't know if any of the changes would be breaking. Perhaps then,x1e80100-dell-tributo-9345anddell,tributo-9345respectively, as this would be the shortest yet most complete description? 'Tributo' already implies its XPS 13" and chassis variation (touchar, hidden trackpad etc etc), '9345' implies XPS 13" of 2024 (?) and in combination with chassis variant pinpoints the model. Otherwise, if it's strongly desired to use marketing names it can be reduced down tox1e80100-dell-9345.dtsanddell,9345altogether as
9345 implies it being both 'XPS' series and 13", and we can hope that by 2034 Dell won't repeat the same mistake with naming. Curious to hear maintainers' opinions as well.
P.S. I've sent the V3 version of the series, it probably makes sense to move this conversation there for visibility.Alex
Quoted 884 lines
---
Thanks & Best Regards, LaurentiuQuoted 879 lines
2 files changed, 861 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dtsarch/arm64/boot/dts/qcom/Makefile +1
-0@@ -271,6 +271,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e78100-lenovo-thinkpad-t14s.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-asus-vivobook-s15.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb +dtb-$(CONFIG_ARCH_QCOM) += x1e80100-dell-tributo-13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-lenovo-yoga-slim7x.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus15.dtbarch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts new file +853
-0@@ -0,0 +1,860 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + * Copyright (c) 2024 Aleksandrs Vinarskis +<[email protected]> */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> #include +<dt-bindings/input/input.h> #include <dt-bindings/leds/common.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +#include "x1e80100.dtsi" +#include "x1e80100-pmics.dtsi" + +/ { + model = "Dell XPS 13 9345"; + compatible = "dell,tributo-13", "qcom,x1e80100"; + chassis-type = "laptop"; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&hall_int_n_default>; + pinctrl-names = "default"; + + switch-lid { + gpios = <&tlmm 92 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + wakeup-source; + wakeup-event-action = <EV_ACT_DEASSERTED>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&cam_indicator_en>; + + led-camera-indicator { + label = "white:camera-indicator"; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_WHITE>; + gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + /* Reuse as a panic indicator until we get a "camera on" trigger */ + panic-indicator; + }; + }; + + pmic-glink { + compatible = "qcom,x1e80100-pmic-glink", + "qcom,sm8550-pmic-glink", + "qcom,pmic-glink"; + orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, + <&tlmm 123 GPIO_ACTIVE_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + /* Right-side USB Type-C port */ + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss0_hs_in: endpoint { + remote-endpoint = <&usb_1_ss0_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss0_ss_in: endpoint { + remote-endpoint = <&usb_1_ss0_qmpphy_out>; + }; + }; + }; + }; + + /* Left-side USB Type-C port */ + connector@1 { + compatible = "usb-c-connector"; + reg = <1>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss1_hs_in: endpoint { + remote-endpoint = <&usb_1_ss1_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss1_ss_in: endpoint { + remote-endpoint = <&usb_1_ss1_qmpphy_out>; + }; + }; + }; + }; + }; + + reserved-memory { + linux,cma { + compatible = "shared-dma-pool"; + size = <0x0 0x8000000>; + reusable; + linux,cma-default; + }; + }; + + vreg_edp_3p3: regulator-edp-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_EDP_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&edp_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_nvme: regulator-nvme { + compatible = "regulator-fixed"; + + regulator-name = "VREG_NVME_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&nvme_reg_en>; + pinctrl-names = "default"; + }; + + vreg_vph_pwr: regulator-vph-pwr { + compatible = "regulator-fixed"; + + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8550-rpmh-regulators"; + qcom,pmic-id = "b"; + vdd-bob1-supply = <&vreg_vph_pwr>; + vdd-bob2-supply = <&vreg_vph_pwr>; + vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; + vdd-l2-l13-l14-supply = <&vreg_bob1>; + vdd-l5-l16-supply = <&vreg_bob1>; + vdd-l6-l7-supply = <&vreg_bob2>; + vdd-l8-l9-supply = <&vreg_bob1>; + vdd-l12-supply = <&vreg_s5j_1p2>; + vdd-l15-supply = <&vreg_s4c_1p8>; + vdd-l17-supply = <&vreg_bob2>; + + vreg_bob1: bob1 { + regulator-name = "vreg_bob1"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob2: bob2 { + regulator-name = "vreg_bob2"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-name = "vreg_l2b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4b_1p8: ldo4 { + regulator-name = "vreg_l4b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p8: ldo6 { + regulator-name = "vreg_l6b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8b_3p0: ldo8 { + regulator-name = "vreg_l8b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_2p9: ldo9 { + regulator-name = "vreg_l9b_2p9"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12b_1p2: ldo12 { + regulator-name = "vreg_l12b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13b_3p0: ldo13 { + regulator-name = "vreg_l13b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14b_3p0: ldo14 { + regulator-name = "vreg_l14b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15b_1p8: ldo15 { + regulator-name = "vreg_l15b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17b_2p5: ldo17 { + regulator-name = "vreg_l17b_2p5"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "c"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s1f_0p7>; + + vreg_s4c_1p8: smps4 { + regulator-name = "vreg_s4c_1p8"; + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1c_1p2: ldo1 { + regulator-name = "vreg_l1c_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c_0p8: ldo2 { + regulator-name = "vreg_l2c_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c_0p9: ldo3 { + regulator-name = "vreg_l3c_0p9"; + regulator-min-microvolt = <920000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "d"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s4c_1p8>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_l1d_0p8: ldo1 { + regulator-name = "vreg_l1d_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2d_0p9: ldo2 { + regulator-name = "vreg_l2d_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3d_1p8: ldo3 { + regulator-name = "vreg_l3d_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-3 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "e"; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s5j_1p2>; + + vreg_l2e_0p8: ldo2 { + regulator-name = "vreg_l2e_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3e_1p2: ldo3 { + regulator-name = "vreg_l3e_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-4 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "f"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s5j_1p2>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_s1f_0p7: smps1 { + regulator-name = "vreg_s1f_0p7"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-6 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "i"; + vdd-l1-supply = <&vreg_s4c_1p8>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s1-supply = <&vreg_vph_pwr>; + vdd-s2-supply = <&vreg_vph_pwr>; + + vreg_s1i_0p9: smps1 { + regulator-name = "vreg_s1i_0p9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s2i_1p0: smps2 { + regulator-name = "vreg_s2i_1p0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1i_1p8: ldo1 { + regulator-name = "vreg_l1i_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2i_1p2: ldo2 { + regulator-name = "vreg_l2i_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3i_0p8: ldo3 { + regulator-name = "vreg_l3i_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-7 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "j"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s5-supply = <&vreg_vph_pwr>; + + vreg_s5j_1p2: smps5 { + regulator-name = "vreg_s5j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1j_0p9: ldo1 { + regulator-name = "vreg_l1j_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2j_1p2: ldo2 { + regulator-name = "vreg_l2j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3j_0p8: ldo3 { + regulator-name = "vreg_l3j_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&gpu { + status = "okay"; + + zap-shader { + firmware-name = "qcom/x1e80100/dell/tributo/qcdxkmsuc8380.mbn"; + }; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + keyboard@5 { + compatible = "hid-over-i2c"; + reg = <0x5>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&kybd_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c5 { + clock-frequency = <100000>; + status = "disabled"; + /* Unknown device @0x3b */ +}; + +&i2c7 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c8 { + clock-frequency = <400000>; + + status = "okay"; + + touchscreen@0 { + compatible = "hid-over-i2c"; + reg = <0x0>; + + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&ts0_default>; + pinctrl-names = "default"; + }; +}; + +&i2c9 { + clock-frequency = <400000>; + status = "disabled"; + /* USB3 retimer device @0x4f */ }; + +&i2c17 { + clock-frequency = <400000>; + status = "okay"; + + touchpad@2c { + compatible = "hid-over-i2c"; + reg = <0x2c>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&tpad_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp3 { + compatible = "qcom,x1e80100-dp"; + /delete-property/ #sound-dai-cells; + + status = "okay"; + + aux-bus { + panel { + /* 1920x1200 IPS panel is SHP1593, PNP09FF compatible */ + compatible = "edp-panel"; + power-supply = <&vreg_edp_3p3>; + + port { + edp_panel_in: endpoint { + remote-endpoint = <&mdss_dp3_out>; + }; + }; + }; + }; + + ports { + port@1 { + reg = <1>; + + mdss_dp3_out: endpoint { + data-lanes = <0 1 2 3>; + link-frequencies = /bits/ 64 + <1620000000 2700000000 5400000000 8100000000>; + + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +}; + +&mdss_dp3_phy { + vdda-phy-supply = <&vreg_l3j_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&pcie4 { + perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&pcie4_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie4_phy { + vdda-phy-supply = <&vreg_l3i_0p8>; + vdda-pll-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&pcie6a { + perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; + + vddpe-3v3-supply = <&vreg_nvme>; + + pinctrl-0 = <&pcie6a_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie6a_phy { + vdda-phy-supply = <&vreg_l1d_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&qupv3_0 { + status = "okay"; +}; + +&qupv3_1 { + status = "okay"; +}; + +&qupv3_2 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/x1e80100/dell/tributo/qcadsp8380.mbn", + "qcom/x1e80100/dell/tributo/adsp_dtbs.elf"; + + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/x1e80100/dell/tributo/qccdsp8380.mbn", + "qcom/x1e80100/dell/tributo/cdsp_dtbs.elf"; + + status = "okay"; +}; + +&smb2360_0_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l2b_3p0>; }; + +&smb2360_1_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l14b_3p0>; }; + +&tlmm { + gpio-reserved-ranges = <44 4>, /* SPI11 (TPM) */ + <76 4>, /* SPI19 (TZ Protected) */ + <238 1>; /* UFS Reset */ + + cam_indicator_en: cam-indicator-en-state { + pins = "gpio110"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + edp_reg_en: edp-reg-en-state { + pins = "gpio70"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + hall_int_n_default: hall-int-n-state { + pins = "gpio92"; + function = "gpio"; + + bias-disable; + }; + + kybd_default: kybd-default-state { + pins = "gpio67"; + function = "gpio"; + bias-pull-up; + }; + + nvme_reg_en: nvme-reg-en-state { + pins = "gpio18"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + pcie4_default: pcie4-default-state { + clkreq-n-pins { + pins = "gpio147"; + function = "pcie4_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio146"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio148"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie6a_default: pcie6a-default-state { + clkreq-n-pins { + pins = "gpio153"; + function = "pcie6a_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio152"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio154"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + tpad_default: tpad-default-state { + disable-pins { + pins = "gpio38"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio3"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + pins = "gpio52"; + function = "gpio"; + bias-disable; + }; + }; + + ts0_default: ts0-default-state { + disable-pins { + pins = "gpio75"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio51"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + /* Technically should be High-Z input */ + pins = "gpio48"; + function = "gpio"; + output-low; + drive-strength = <2>; + }; + }; +}; + +&uart21 { + compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; + +&usb_1_ss0_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_0_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss0_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l1j_0p9>; + + status = "okay"; +}; + +&usb_1_ss0 { + status = "okay"; +}; + +&usb_1_ss0_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss0_dwc3_hs { + remote-endpoint = <&pmic_glink_ss0_hs_in>; }; + +&usb_1_ss0_qmpphy_out { + remote-endpoint = <&pmic_glink_ss0_ss_in>; }; + +&usb_1_ss1_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_1_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss1_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l2d_0p9>; + + status = "okay"; +}; + +&usb_1_ss1 { + status = "okay"; +}; + +&usb_1_ss1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss1_dwc3_hs { + remote-endpoint = <&pmic_glink_ss1_hs_in>; }; + +&usb_1_ss1_qmpphy_out { + remote-endpoint = <&pmic_glink_ss1_ss_in>; };
Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
Quoted 23 lines · Laurentiu Tudor
Hi Alex,
Quoted 11 lines · Aleksandrs Vinarskis
Quoted 3 lines · Bryan
Fascinating topic. First of all, thank you Alex for the explanation of your logic, and thank you as well for the work on the device tree for the XPS 13. I understand completely how the Dell naming/numbering scheme is confusing. The shortened version down to just the model number could also be confusing. For example, there is an XPS 9520 as well as a Latitude 9520. The 9 basically translates to "premium" not a specific line of business. For what it is worth, I would prefer the dell-xps13-9345 naming and I think we can have to be mindful to avoid a naming collision in a decade.
Hi,
Thanks for the input, it's really nice to have Dell's perspective as well. That's a good point with latitude, I was only aware of 5XXX/7XXX naming for that one... which I guess further highlights the confusing naming scheme.
Yeah, completely agree. We will raise this internally so that in the future we'll do a better job at naming platforms.
Quoted 3 lines
I will re-spin with
dell-xps13-9345anddell,xps13-9345respectively as proposed then, unless there will be any other feedback on the V3 series before tomorrow.
Quoted 6 lines
Great, thanks!
Couple of points:
- i'm thinking that maybe at a later point, as more dell platforms are
getting added, we can re-organize the device trees, e.g. have a common 'dell-xps.dtsi' which gets inherited by specific platforms
Completely agree. Although I'm not sure about the name - analyzing DSDT of Tributo it seems there are quite a few more things defined than particular laptop utilizes, eg. support for x3 TypeC and x3 USB MP while current device only has x2 TypeC and x1 USB MP. I believe these are either leftovers of examples being provided to Dell which were just left there, or ACPI tables being (at least partially?) shared between multiple platforms - eg. Inspiron 14" 7441/Latitude 14" 5455 etc. In the latter case (unfortunately cannot test myself due to lack of hw) perhaps the .dtsi can be inherited by more than just XPS family. If you/Kemp Bryan could share some insight on that already wrt to how much is shared (if any), I can split to dtsi/dts with upcoming re-spin. Otherwise indeed can be done when the next platform is being introduced.
Quoted 3 lines
- just noticed that the firmware paths point to something like
".../dell/tributo/...". Should we reconsider these too? Maybe something like ".../dell/xps/..." would be better?
Yes, will drop 'tributo' altogether. Perhaps "../dell/xps13-9345" then, to match the proposed compat? Also when Divo/Huracan/Perfomante will come out, those are still "XPS" but I would guess will have different firmware files, so maybe it makes sense to be a bit more precise with the naming?
Regards,
Alex
Quoted 969 lines
---
Thanks & Best Regards, LaurentiuQuoted 964 lines
Thanks,
AlexQuoted 961 lines
Thanks again for the support.
Bryan Kemp
Architect - Linux OS EngineeringInternal Use - Confidential
-----Original Message-----
From: Aleksandrs Vinarskis <[email protected]>
Sent: Monday, September 30, 2024 2:24 PM
To: Laurentiu Tudor <[email protected]>
Cc: Bjorn Andersson <[email protected]>; Krzysztof Kozlowski <[email protected]>; Dmitry Baryshkov <[email protected]>; [email protected]; [email protected]; [email protected]; Tudor, Laurentiu <[email protected]>; Konrad Dybcio <[email protected]>; Rob Herring <[email protected]>; Krzysztof Kozlowski <[email protected]>; Conor Dooley <[email protected]>; Rob Clark <[email protected]>; Peter de Kraker <[email protected]>; Kemp, Bryan <[email protected]>
Subject: Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345[EXTERNAL EMAIL]
Quoted 37 lines · Laurentiu Tudor
Hi Alex,
Thanks for this! Comment inline.
Quoted 21 lines · Aleksandrs Vinarskis
Initial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resumeNot working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery InfoQuoted 8 lines
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panels
* TouchscreenSigned-off-by Aleksandrs Vinarskis <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 1 + .../dts/qcom/x1e80100-dell-tributo-13.dts | 860 ++++++++++++++++++Quoted 4 lines
Could you please use the marketing name for the device tree file name & machine compatible, e.g. "
x1e80100-dell-xps13-9345.dts" for the dts file and "dell,xps13-9345" for the compat? I'm thinking that this will help people to identify it more easily.Hi,
Even though I agree that it may be easier to identify for a non-developer, I am a bit skeptical as Dell has a pretty weird naming convention which sometimes results in the name being non-unique.
In particular case - 9345 - 9 stands for XPS series, 3 stands for 13", and 45 would typically be the last digit of year + 0 (so 40), but with the introduction of last year's ''13 Plus"series they added a 5. At present, this is unique, however in 10 years it may not be.I have recently hit this issue when working on Dell XPS 15" 2024 (9530), which has the same model number as Dell XPS 15" 2013 and led to huge confusions. Only way to distinguish them is by codename ('fiorano' for the newer one), or using a complete name including the year... The codename on the other hand is easily searchable both in the source code and online.
I tried to browse the source code for existing notation, but didn't find anything strongly supporting one or another way, so decided to follow Microsoft Surface's example with codenames ('romulus').
Codenaming is also imperfect though, as in Dell's case it typically refers to chassis, rather than _the_ particular device, which typically lasts several years. Typically throughout chassis generation internals stay +/- the same, but we can't know if any of the changes would be breaking. Perhaps then,x1e80100-dell-tributo-9345anddell,tributo-9345respectively, as this would be the shortest yet most complete description? 'Tributo' already implies its XPS 13" and chassis variation (touchar, hidden trackpad etc etc), '9345' implies XPS 13" of 2024 (?) and in combination with chassis variant pinpoints the model. Otherwise, if it's strongly desired to use marketing names it can be reduced down tox1e80100-dell-9345.dtsanddell,9345altogether as
9345 implies it being both 'XPS' series and 13", and we can hope that by 2034 Dell won't repeat the same mistake with naming. Curious to hear maintainers' opinions as well.
P.S. I've sent the V3 version of the series, it probably makes sense to move this conversation there for visibility.Alex
Quoted 884 lines
---
Thanks & Best Regards, LaurentiuQuoted 879 lines
2 files changed, 861 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dtsarch/arm64/boot/dts/qcom/Makefile +1
-0@@ -271,6 +271,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e78100-lenovo-thinkpad-t14s.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-asus-vivobook-s15.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb +dtb-$(CONFIG_ARCH_QCOM) += x1e80100-dell-tributo-13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-lenovo-yoga-slim7x.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus15.dtbarch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts new file +853
-0@@ -0,0 +1,860 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + * Copyright (c) 2024 Aleksandrs Vinarskis +<[email protected]> */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> #include +<dt-bindings/input/input.h> #include <dt-bindings/leds/common.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +#include "x1e80100.dtsi" +#include "x1e80100-pmics.dtsi" + +/ { + model = "Dell XPS 13 9345"; + compatible = "dell,tributo-13", "qcom,x1e80100"; + chassis-type = "laptop"; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&hall_int_n_default>; + pinctrl-names = "default"; + + switch-lid { + gpios = <&tlmm 92 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + wakeup-source; + wakeup-event-action = <EV_ACT_DEASSERTED>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&cam_indicator_en>; + + led-camera-indicator { + label = "white:camera-indicator"; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_WHITE>; + gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + /* Reuse as a panic indicator until we get a "camera on" trigger */ + panic-indicator; + }; + }; + + pmic-glink { + compatible = "qcom,x1e80100-pmic-glink", + "qcom,sm8550-pmic-glink", + "qcom,pmic-glink"; + orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, + <&tlmm 123 GPIO_ACTIVE_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + /* Right-side USB Type-C port */ + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss0_hs_in: endpoint { + remote-endpoint = <&usb_1_ss0_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss0_ss_in: endpoint { + remote-endpoint = <&usb_1_ss0_qmpphy_out>; + }; + }; + }; + }; + + /* Left-side USB Type-C port */ + connector@1 { + compatible = "usb-c-connector"; + reg = <1>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss1_hs_in: endpoint { + remote-endpoint = <&usb_1_ss1_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss1_ss_in: endpoint { + remote-endpoint = <&usb_1_ss1_qmpphy_out>; + }; + }; + }; + }; + }; + + reserved-memory { + linux,cma { + compatible = "shared-dma-pool"; + size = <0x0 0x8000000>; + reusable; + linux,cma-default; + }; + }; + + vreg_edp_3p3: regulator-edp-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_EDP_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&edp_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_nvme: regulator-nvme { + compatible = "regulator-fixed"; + + regulator-name = "VREG_NVME_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&nvme_reg_en>; + pinctrl-names = "default"; + }; + + vreg_vph_pwr: regulator-vph-pwr { + compatible = "regulator-fixed"; + + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8550-rpmh-regulators"; + qcom,pmic-id = "b"; + vdd-bob1-supply = <&vreg_vph_pwr>; + vdd-bob2-supply = <&vreg_vph_pwr>; + vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; + vdd-l2-l13-l14-supply = <&vreg_bob1>; + vdd-l5-l16-supply = <&vreg_bob1>; + vdd-l6-l7-supply = <&vreg_bob2>; + vdd-l8-l9-supply = <&vreg_bob1>; + vdd-l12-supply = <&vreg_s5j_1p2>; + vdd-l15-supply = <&vreg_s4c_1p8>; + vdd-l17-supply = <&vreg_bob2>; + + vreg_bob1: bob1 { + regulator-name = "vreg_bob1"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob2: bob2 { + regulator-name = "vreg_bob2"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-name = "vreg_l2b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4b_1p8: ldo4 { + regulator-name = "vreg_l4b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p8: ldo6 { + regulator-name = "vreg_l6b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8b_3p0: ldo8 { + regulator-name = "vreg_l8b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_2p9: ldo9 { + regulator-name = "vreg_l9b_2p9"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12b_1p2: ldo12 { + regulator-name = "vreg_l12b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13b_3p0: ldo13 { + regulator-name = "vreg_l13b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14b_3p0: ldo14 { + regulator-name = "vreg_l14b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15b_1p8: ldo15 { + regulator-name = "vreg_l15b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17b_2p5: ldo17 { + regulator-name = "vreg_l17b_2p5"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "c"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s1f_0p7>; + + vreg_s4c_1p8: smps4 { + regulator-name = "vreg_s4c_1p8"; + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1c_1p2: ldo1 { + regulator-name = "vreg_l1c_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c_0p8: ldo2 { + regulator-name = "vreg_l2c_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c_0p9: ldo3 { + regulator-name = "vreg_l3c_0p9"; + regulator-min-microvolt = <920000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "d"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s4c_1p8>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_l1d_0p8: ldo1 { + regulator-name = "vreg_l1d_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2d_0p9: ldo2 { + regulator-name = "vreg_l2d_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3d_1p8: ldo3 { + regulator-name = "vreg_l3d_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-3 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "e"; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s5j_1p2>; + + vreg_l2e_0p8: ldo2 { + regulator-name = "vreg_l2e_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3e_1p2: ldo3 { + regulator-name = "vreg_l3e_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-4 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "f"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s5j_1p2>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_s1f_0p7: smps1 { + regulator-name = "vreg_s1f_0p7"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-6 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "i"; + vdd-l1-supply = <&vreg_s4c_1p8>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s1-supply = <&vreg_vph_pwr>; + vdd-s2-supply = <&vreg_vph_pwr>; + + vreg_s1i_0p9: smps1 { + regulator-name = "vreg_s1i_0p9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s2i_1p0: smps2 { + regulator-name = "vreg_s2i_1p0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1i_1p8: ldo1 { + regulator-name = "vreg_l1i_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2i_1p2: ldo2 { + regulator-name = "vreg_l2i_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3i_0p8: ldo3 { + regulator-name = "vreg_l3i_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-7 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "j"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s5-supply = <&vreg_vph_pwr>; + + vreg_s5j_1p2: smps5 { + regulator-name = "vreg_s5j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1j_0p9: ldo1 { + regulator-name = "vreg_l1j_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2j_1p2: ldo2 { + regulator-name = "vreg_l2j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3j_0p8: ldo3 { + regulator-name = "vreg_l3j_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&gpu { + status = "okay"; + + zap-shader { + firmware-name = "qcom/x1e80100/dell/tributo/qcdxkmsuc8380.mbn"; + }; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + keyboard@5 { + compatible = "hid-over-i2c"; + reg = <0x5>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&kybd_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c5 { + clock-frequency = <100000>; + status = "disabled"; + /* Unknown device @0x3b */ +}; + +&i2c7 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c8 { + clock-frequency = <400000>; + + status = "okay"; + + touchscreen@0 { + compatible = "hid-over-i2c"; + reg = <0x0>; + + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&ts0_default>; + pinctrl-names = "default"; + }; +}; + +&i2c9 { + clock-frequency = <400000>; + status = "disabled"; + /* USB3 retimer device @0x4f */ }; + +&i2c17 { + clock-frequency = <400000>; + status = "okay"; + + touchpad@2c { + compatible = "hid-over-i2c"; + reg = <0x2c>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&tpad_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp3 { + compatible = "qcom,x1e80100-dp"; + /delete-property/ #sound-dai-cells; + + status = "okay"; + + aux-bus { + panel { + /* 1920x1200 IPS panel is SHP1593, PNP09FF compatible */ + compatible = "edp-panel"; + power-supply = <&vreg_edp_3p3>; + + port { + edp_panel_in: endpoint { + remote-endpoint = <&mdss_dp3_out>; + }; + }; + }; + }; + + ports { + port@1 { + reg = <1>; + + mdss_dp3_out: endpoint { + data-lanes = <0 1 2 3>; + link-frequencies = /bits/ 64 + <1620000000 2700000000 5400000000 8100000000>; + + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +}; + +&mdss_dp3_phy { + vdda-phy-supply = <&vreg_l3j_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&pcie4 { + perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&pcie4_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie4_phy { + vdda-phy-supply = <&vreg_l3i_0p8>; + vdda-pll-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&pcie6a { + perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; + + vddpe-3v3-supply = <&vreg_nvme>; + + pinctrl-0 = <&pcie6a_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie6a_phy { + vdda-phy-supply = <&vreg_l1d_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&qupv3_0 { + status = "okay"; +}; + +&qupv3_1 { + status = "okay"; +}; + +&qupv3_2 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/x1e80100/dell/tributo/qcadsp8380.mbn", + "qcom/x1e80100/dell/tributo/adsp_dtbs.elf"; + + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/x1e80100/dell/tributo/qccdsp8380.mbn", + "qcom/x1e80100/dell/tributo/cdsp_dtbs.elf"; + + status = "okay"; +}; + +&smb2360_0_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l2b_3p0>; }; + +&smb2360_1_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l14b_3p0>; }; + +&tlmm { + gpio-reserved-ranges = <44 4>, /* SPI11 (TPM) */ + <76 4>, /* SPI19 (TZ Protected) */ + <238 1>; /* UFS Reset */ + + cam_indicator_en: cam-indicator-en-state { + pins = "gpio110"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + edp_reg_en: edp-reg-en-state { + pins = "gpio70"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + hall_int_n_default: hall-int-n-state { + pins = "gpio92"; + function = "gpio"; + + bias-disable; + }; + + kybd_default: kybd-default-state { + pins = "gpio67"; + function = "gpio"; + bias-pull-up; + }; + + nvme_reg_en: nvme-reg-en-state { + pins = "gpio18"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + pcie4_default: pcie4-default-state { + clkreq-n-pins { + pins = "gpio147"; + function = "pcie4_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio146"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio148"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie6a_default: pcie6a-default-state { + clkreq-n-pins { + pins = "gpio153"; + function = "pcie6a_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio152"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio154"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + tpad_default: tpad-default-state { + disable-pins { + pins = "gpio38"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio3"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + pins = "gpio52"; + function = "gpio"; + bias-disable; + }; + }; + + ts0_default: ts0-default-state { + disable-pins { + pins = "gpio75"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio51"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + /* Technically should be High-Z input */ + pins = "gpio48"; + function = "gpio"; + output-low; + drive-strength = <2>; + }; + }; +}; + +&uart21 { + compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; + +&usb_1_ss0_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_0_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss0_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l1j_0p9>; + + status = "okay"; +}; + +&usb_1_ss0 { + status = "okay"; +}; + +&usb_1_ss0_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss0_dwc3_hs { + remote-endpoint = <&pmic_glink_ss0_hs_in>; }; + +&usb_1_ss0_qmpphy_out { + remote-endpoint = <&pmic_glink_ss0_ss_in>; }; + +&usb_1_ss1_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_1_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss1_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l2d_0p9>; + + status = "okay"; +}; + +&usb_1_ss1 { + status = "okay"; +}; + +&usb_1_ss1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss1_dwc3_hs { + remote-endpoint = <&pmic_glink_ss1_hs_in>; }; + +&usb_1_ss1_qmpphy_out { + remote-endpoint = <&pmic_glink_ss1_ss_in>; };
Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
Hi Alex,
Quoted 32 lines · Aleksandrs Vinarskis
Quoted 23 lines · Laurentiu Tudor
Hi Alex,
Quoted 11 lines · Aleksandrs Vinarskis
Quoted 3 lines · Bryan
Fascinating topic. First of all, thank you Alex for the explanation of your logic, and thank you as well for the work on the device tree for the XPS 13. I understand completely how the Dell naming/numbering scheme is confusing. The shortened version down to just the model number could also be confusing. For example, there is an XPS 9520 as well as a Latitude 9520. The 9 basically translates to "premium" not a specific line of business. For what it is worth, I would prefer the dell-xps13-9345 naming and I think we can have to be mindful to avoid a naming collision in a decade.
Hi,
Thanks for the input, it's really nice to have Dell's perspective as well. That's a good point with latitude, I was only aware of 5XXX/7XXX naming for that one... which I guess further highlights the confusing naming scheme.
Yeah, completely agree. We will raise this internally so that in the future we'll do a better job at naming platforms.
Quoted 3 lines
I will re-spin with
dell-xps13-9345anddell,xps13-9345respectively as proposed then, unless there will be any other feedback on the V3 series before tomorrow.Quoted 6 lines
Great, thanks!
Couple of points:
- i'm thinking that maybe at a later point, as more dell platforms are
getting added, we can re-organize the device trees, e.g. have a common 'dell-xps.dtsi' which gets inherited by specific platforms
Quoted 13 lines
Completely agree. Although I'm not sure about the name - analyzing DSDT of Tributo it seems there are quite a few more things defined than particular laptop utilizes, eg. support for x3 TypeC and x3 USB MP while current device only has x2 TypeC and x1 USB MP. I believe these are either leftovers of examples being provided to Dell which were just left there, or ACPI tables being (at least partially?) shared between multiple platforms - eg. Inspiron 14" 7441/Latitude 14" 5455 etc. In the latter case (unfortunately cannot test myself due to lack of hw) perhaps the .dtsi can be inherited by more than just XPS family. If you/Kemp Bryan could share some insight on that already wrt to how much is shared (if any), I can split to dtsi/dts with upcoming re-spin. Otherwise indeed can be done when the next platform is being introduced.
Regarding ACPI, hard to tell as I'm not familiar with what's exposed in there... there might be legacy / inconsistent things.
For now, I'd suggest to just stick with what we have at the moment and build on that. More to the point, have the device tree for xps13-9345 accepted and derive from it, if / when at some point in time similar platforms show up.
Quoted 6 lines
Quoted 3 lines
- just noticed that the firmware paths point to something like
".../dell/tributo/...". Should we reconsider these too? Maybe something like ".../dell/xps/..." would be better?Yes, will drop 'tributo' altogether. Perhaps "../dell/xps13-9345" then, to match the proposed compat?
Sounds good to me.
Quoted 4 lines
Also when Divo/Huracan/Perfomante
will come out, those are still "XPS" but I would guess will have different firmware files, so maybe it makes sense to be a bit more precise with the naming?
On naming, there are ongoing internal discussions to make them more coherent.
Apart from that, could you please Cc: us if you plan to submit stuff to linux-firmware?
---
Thanks & Best Regards, Laurentiu!
Quoted 963 lines
Quoted 963 lines
Quoted 962 lines
Quoted 962 lines
Thanks again for the support.
Bryan Kemp
Architect - Linux OS EngineeringInternal Use - Confidential
-----Original Message-----
From: Aleksandrs Vinarskis <[email protected]>
Sent: Monday, September 30, 2024 2:24 PM
To: Laurentiu Tudor <[email protected]>
Cc: Bjorn Andersson <[email protected]>; Krzysztof Kozlowski <[email protected]>; Dmitry Baryshkov <[email protected]>; [email protected]; [email protected]; [email protected]; Tudor, Laurentiu <[email protected]>; Konrad Dybcio <[email protected]>; Rob Herring <[email protected]>; Krzysztof Kozlowski <[email protected]>; Conor Dooley <[email protected]>; Rob Clark <[email protected]>; Peter de Kraker <[email protected]>; Kemp, Bryan <[email protected]>
Subject: Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345[EXTERNAL EMAIL]
Quoted 37 lines · Laurentiu Tudor
Hi Alex,
Thanks for this! Comment inline.
Quoted 21 lines · Aleksandrs Vinarskis
Initial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resumeNot working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery InfoQuoted 8 lines
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panels
* TouchscreenSigned-off-by Aleksandrs Vinarskis <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 1 + .../dts/qcom/x1e80100-dell-tributo-13.dts | 860 ++++++++++++++++++Quoted 4 lines
Could you please use the marketing name for the device tree file name & machine compatible, e.g. "
x1e80100-dell-xps13-9345.dts" for the dts file and "dell,xps13-9345" for the compat? I'm thinking that this will help people to identify it more easily.Hi,
Even though I agree that it may be easier to identify for a non-developer, I am a bit skeptical as Dell has a pretty weird naming convention which sometimes results in the name being non-unique.
In particular case - 9345 - 9 stands for XPS series, 3 stands for 13", and 45 would typically be the last digit of year + 0 (so 40), but with the introduction of last year's ''13 Plus"series they added a 5. At present, this is unique, however in 10 years it may not be.I have recently hit this issue when working on Dell XPS 15" 2024 (9530), which has the same model number as Dell XPS 15" 2013 and led to huge confusions. Only way to distinguish them is by codename ('fiorano' for the newer one), or using a complete name including the year... The codename on the other hand is easily searchable both in the source code and online.
I tried to browse the source code for existing notation, but didn't find anything strongly supporting one or another way, so decided to follow Microsoft Surface's example with codenames ('romulus').
Codenaming is also imperfect though, as in Dell's case it typically refers to chassis, rather than _the_ particular device, which typically lasts several years. Typically throughout chassis generation internals stay +/- the same, but we can't know if any of the changes would be breaking. Perhaps then,x1e80100-dell-tributo-9345anddell,tributo-9345respectively, as this would be the shortest yet most complete description? 'Tributo' already implies its XPS 13" and chassis variation (touchar, hidden trackpad etc etc), '9345' implies XPS 13" of 2024 (?) and in combination with chassis variant pinpoints the model. Otherwise, if it's strongly desired to use marketing names it can be reduced down tox1e80100-dell-9345.dtsanddell,9345altogether as
9345 implies it being both 'XPS' series and 13", and we can hope that by 2034 Dell won't repeat the same mistake with naming. Curious to hear maintainers' opinions as well.
P.S. I've sent the V3 version of the series, it probably makes sense to move this conversation there for visibility.Alex
Quoted 884 lines
---
Thanks & Best Regards, LaurentiuQuoted 879 lines
2 files changed, 861 insertions(+) create mode 100644
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dtsarch/arm64/boot/dts/qcom/Makefile +1
-0@@ -271,6 +271,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e78100-lenovo-thinkpad-t14s.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-asus-vivobook-s15.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb +dtb-$(CONFIG_ARCH_QCOM) += x1e80100-dell-tributo-13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-lenovo-yoga-slim7x.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus15.dtbarch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts new file +853
-0@@ -0,0 +1,860 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + * Copyright (c) 2024 Aleksandrs Vinarskis +<[email protected]> */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> #include +<dt-bindings/input/input.h> #include <dt-bindings/leds/common.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +#include "x1e80100.dtsi" +#include "x1e80100-pmics.dtsi" + +/ { + model = "Dell XPS 13 9345"; + compatible = "dell,tributo-13", "qcom,x1e80100"; + chassis-type = "laptop"; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&hall_int_n_default>; + pinctrl-names = "default"; + + switch-lid { + gpios = <&tlmm 92 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + wakeup-source; + wakeup-event-action = <EV_ACT_DEASSERTED>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&cam_indicator_en>; + + led-camera-indicator { + label = "white:camera-indicator"; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_WHITE>; + gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + /* Reuse as a panic indicator until we get a "camera on" trigger */ + panic-indicator; + }; + }; + + pmic-glink { + compatible = "qcom,x1e80100-pmic-glink", + "qcom,sm8550-pmic-glink", + "qcom,pmic-glink"; + orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, + <&tlmm 123 GPIO_ACTIVE_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + /* Right-side USB Type-C port */ + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss0_hs_in: endpoint { + remote-endpoint = <&usb_1_ss0_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss0_ss_in: endpoint { + remote-endpoint = <&usb_1_ss0_qmpphy_out>; + }; + }; + }; + }; + + /* Left-side USB Type-C port */ + connector@1 { + compatible = "usb-c-connector"; + reg = <1>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss1_hs_in: endpoint { + remote-endpoint = <&usb_1_ss1_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss1_ss_in: endpoint { + remote-endpoint = <&usb_1_ss1_qmpphy_out>; + }; + }; + }; + }; + }; + + reserved-memory { + linux,cma { + compatible = "shared-dma-pool"; + size = <0x0 0x8000000>; + reusable; + linux,cma-default; + }; + }; + + vreg_edp_3p3: regulator-edp-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_EDP_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&edp_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_nvme: regulator-nvme { + compatible = "regulator-fixed"; + + regulator-name = "VREG_NVME_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&nvme_reg_en>; + pinctrl-names = "default"; + }; + + vreg_vph_pwr: regulator-vph-pwr { + compatible = "regulator-fixed"; + + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8550-rpmh-regulators"; + qcom,pmic-id = "b"; + vdd-bob1-supply = <&vreg_vph_pwr>; + vdd-bob2-supply = <&vreg_vph_pwr>; + vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; + vdd-l2-l13-l14-supply = <&vreg_bob1>; + vdd-l5-l16-supply = <&vreg_bob1>; + vdd-l6-l7-supply = <&vreg_bob2>; + vdd-l8-l9-supply = <&vreg_bob1>; + vdd-l12-supply = <&vreg_s5j_1p2>; + vdd-l15-supply = <&vreg_s4c_1p8>; + vdd-l17-supply = <&vreg_bob2>; + + vreg_bob1: bob1 { + regulator-name = "vreg_bob1"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob2: bob2 { + regulator-name = "vreg_bob2"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-name = "vreg_l2b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4b_1p8: ldo4 { + regulator-name = "vreg_l4b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p8: ldo6 { + regulator-name = "vreg_l6b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8b_3p0: ldo8 { + regulator-name = "vreg_l8b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_2p9: ldo9 { + regulator-name = "vreg_l9b_2p9"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12b_1p2: ldo12 { + regulator-name = "vreg_l12b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13b_3p0: ldo13 { + regulator-name = "vreg_l13b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14b_3p0: ldo14 { + regulator-name = "vreg_l14b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15b_1p8: ldo15 { + regulator-name = "vreg_l15b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17b_2p5: ldo17 { + regulator-name = "vreg_l17b_2p5"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "c"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s1f_0p7>; + + vreg_s4c_1p8: smps4 { + regulator-name = "vreg_s4c_1p8"; + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1c_1p2: ldo1 { + regulator-name = "vreg_l1c_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c_0p8: ldo2 { + regulator-name = "vreg_l2c_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c_0p9: ldo3 { + regulator-name = "vreg_l3c_0p9"; + regulator-min-microvolt = <920000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "d"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s4c_1p8>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_l1d_0p8: ldo1 { + regulator-name = "vreg_l1d_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2d_0p9: ldo2 { + regulator-name = "vreg_l2d_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3d_1p8: ldo3 { + regulator-name = "vreg_l3d_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-3 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "e"; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s5j_1p2>; + + vreg_l2e_0p8: ldo2 { + regulator-name = "vreg_l2e_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3e_1p2: ldo3 { + regulator-name = "vreg_l3e_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-4 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "f"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s5j_1p2>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_s1f_0p7: smps1 { + regulator-name = "vreg_s1f_0p7"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-6 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "i"; + vdd-l1-supply = <&vreg_s4c_1p8>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s1-supply = <&vreg_vph_pwr>; + vdd-s2-supply = <&vreg_vph_pwr>; + + vreg_s1i_0p9: smps1 { + regulator-name = "vreg_s1i_0p9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s2i_1p0: smps2 { + regulator-name = "vreg_s2i_1p0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1i_1p8: ldo1 { + regulator-name = "vreg_l1i_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2i_1p2: ldo2 { + regulator-name = "vreg_l2i_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3i_0p8: ldo3 { + regulator-name = "vreg_l3i_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-7 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "j"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s5-supply = <&vreg_vph_pwr>; + + vreg_s5j_1p2: smps5 { + regulator-name = "vreg_s5j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1j_0p9: ldo1 { + regulator-name = "vreg_l1j_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2j_1p2: ldo2 { + regulator-name = "vreg_l2j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3j_0p8: ldo3 { + regulator-name = "vreg_l3j_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&gpu { + status = "okay"; + + zap-shader { + firmware-name = "qcom/x1e80100/dell/tributo/qcdxkmsuc8380.mbn"; + }; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + keyboard@5 { + compatible = "hid-over-i2c"; + reg = <0x5>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&kybd_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c5 { + clock-frequency = <100000>; + status = "disabled"; + /* Unknown device @0x3b */ +}; + +&i2c7 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c8 { + clock-frequency = <400000>; + + status = "okay"; + + touchscreen@0 { + compatible = "hid-over-i2c"; + reg = <0x0>; + + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&ts0_default>; + pinctrl-names = "default"; + }; +}; + +&i2c9 { + clock-frequency = <400000>; + status = "disabled"; + /* USB3 retimer device @0x4f */ }; + +&i2c17 { + clock-frequency = <400000>; + status = "okay"; + + touchpad@2c { + compatible = "hid-over-i2c"; + reg = <0x2c>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&tpad_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp3 { + compatible = "qcom,x1e80100-dp"; + /delete-property/ #sound-dai-cells; + + status = "okay"; + + aux-bus { + panel { + /* 1920x1200 IPS panel is SHP1593, PNP09FF compatible */ + compatible = "edp-panel"; + power-supply = <&vreg_edp_3p3>; + + port { + edp_panel_in: endpoint { + remote-endpoint = <&mdss_dp3_out>; + }; + }; + }; + }; + + ports { + port@1 { + reg = <1>; + + mdss_dp3_out: endpoint { + data-lanes = <0 1 2 3>; + link-frequencies = /bits/ 64 + <1620000000 2700000000 5400000000 8100000000>; + + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +}; + +&mdss_dp3_phy { + vdda-phy-supply = <&vreg_l3j_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&pcie4 { + perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&pcie4_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie4_phy { + vdda-phy-supply = <&vreg_l3i_0p8>; + vdda-pll-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&pcie6a { + perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; + + vddpe-3v3-supply = <&vreg_nvme>; + + pinctrl-0 = <&pcie6a_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie6a_phy { + vdda-phy-supply = <&vreg_l1d_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&qupv3_0 { + status = "okay"; +}; + +&qupv3_1 { + status = "okay"; +}; + +&qupv3_2 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/x1e80100/dell/tributo/qcadsp8380.mbn", + "qcom/x1e80100/dell/tributo/adsp_dtbs.elf"; + + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/x1e80100/dell/tributo/qccdsp8380.mbn", + "qcom/x1e80100/dell/tributo/cdsp_dtbs.elf"; + + status = "okay"; +}; + +&smb2360_0_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l2b_3p0>; }; + +&smb2360_1_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l14b_3p0>; }; + +&tlmm { + gpio-reserved-ranges = <44 4>, /* SPI11 (TPM) */ + <76 4>, /* SPI19 (TZ Protected) */ + <238 1>; /* UFS Reset */ + + cam_indicator_en: cam-indicator-en-state { + pins = "gpio110"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + edp_reg_en: edp-reg-en-state { + pins = "gpio70"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + hall_int_n_default: hall-int-n-state { + pins = "gpio92"; + function = "gpio"; + + bias-disable; + }; + + kybd_default: kybd-default-state { + pins = "gpio67"; + function = "gpio"; + bias-pull-up; + }; + + nvme_reg_en: nvme-reg-en-state { + pins = "gpio18"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + pcie4_default: pcie4-default-state { + clkreq-n-pins { + pins = "gpio147"; + function = "pcie4_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio146"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio148"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie6a_default: pcie6a-default-state { + clkreq-n-pins { + pins = "gpio153"; + function = "pcie6a_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio152"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio154"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + tpad_default: tpad-default-state { + disable-pins { + pins = "gpio38"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio3"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + pins = "gpio52"; + function = "gpio"; + bias-disable; + }; + }; + + ts0_default: ts0-default-state { + disable-pins { + pins = "gpio75"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio51"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + /* Technically should be High-Z input */ + pins = "gpio48"; + function = "gpio"; + output-low; + drive-strength = <2>; + }; + }; +}; + +&uart21 { + compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; + +&usb_1_ss0_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_0_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss0_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l1j_0p9>; + + status = "okay"; +}; + +&usb_1_ss0 { + status = "okay"; +}; + +&usb_1_ss0_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss0_dwc3_hs { + remote-endpoint = <&pmic_glink_ss0_hs_in>; }; + +&usb_1_ss0_qmpphy_out { + remote-endpoint = <&pmic_glink_ss0_ss_in>; }; + +&usb_1_ss1_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_1_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss1_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l2d_0p9>; + + status = "okay"; +}; + +&usb_1_ss1 { + status = "okay"; +}; + +&usb_1_ss1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss1_dwc3_hs { + remote-endpoint = <&pmic_glink_ss1_hs_in>; }; + +&usb_1_ss1_qmpphy_out { + remote-endpoint = <&pmic_glink_ss1_ss_in>; };
Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
Quoted 63 lines · Laurentiu Tudor
Hi Alex,
Quoted 32 lines · Aleksandrs Vinarskis
Quoted 23 lines · Laurentiu Tudor
Hi Alex,
Quoted 11 lines · Aleksandrs Vinarskis
Quoted 3 lines · Bryan
Fascinating topic. First of all, thank you Alex for the explanation of your logic, and thank you as well for the work on the device tree for the XPS 13. I understand completely how the Dell naming/numbering scheme is confusing. The shortened version down to just the model number could also be confusing. For example, there is an XPS 9520 as well as a Latitude 9520. The 9 basically translates to "premium" not a specific line of business. For what it is worth, I would prefer the dell-xps13-9345 naming and I think we can have to be mindful to avoid a naming collision in a decade.
Hi,
Thanks for the input, it's really nice to have Dell's perspective as well. That's a good point with latitude, I was only aware of 5XXX/7XXX naming for that one... which I guess further highlights the confusing naming scheme.
Yeah, completely agree. We will raise this internally so that in the future we'll do a better job at naming platforms.
Quoted 3 lines
I will re-spin with
dell-xps13-9345anddell,xps13-9345respectively as proposed then, unless there will be any other feedback on the V3 series before tomorrow.Quoted 6 lines
Great, thanks!
Couple of points:
- i'm thinking that maybe at a later point, as more dell platforms are
getting added, we can re-organize the device trees, e.g. have a common 'dell-xps.dtsi' which gets inherited by specific platformsQuoted 13 lines
Completely agree. Although I'm not sure about the name - analyzing DSDT of Tributo it seems there are quite a few more things defined than particular laptop utilizes, eg. support for x3 TypeC and x3 USB MP while current device only has x2 TypeC and x1 USB MP. I believe these are either leftovers of examples being provided to Dell which were just left there, or ACPI tables being (at least partially?) shared between multiple platforms - eg. Inspiron 14" 7441/Latitude 14" 5455 etc. In the latter case (unfortunately cannot test myself due to lack of hw) perhaps the .dtsi can be inherited by more than just XPS family. If you/Kemp Bryan could share some insight on that already wrt to how much is shared (if any), I can split to dtsi/dts with upcoming re-spin. Otherwise indeed can be done when the next platform is being introduced.
Regarding ACPI, hard to tell as I'm not familiar with what's exposed in there... there might be legacy / inconsistent things.
For now, I'd suggest to just stick with what we have at the moment and build on that. More to the point, have the device tree for xps13-9345 accepted and derive from it, if / when at some point in time similar platforms show up.
Quoted 6 lines
Quoted 3 lines
- just noticed that the firmware paths point to something like
".../dell/tributo/...". Should we reconsider these too? Maybe something like ".../dell/xps/..." would be better?Yes, will drop 'tributo' altogether. Perhaps "../dell/xps13-9345" then, to match the proposed compat?
Sounds good to me.
Quoted 8 lines
Quoted 4 lines
Also when Divo/Huracan/Perfomante
will come out, those are still "XPS" but I would guess will have different firmware files, so maybe it makes sense to be a bit more precise with the naming?On naming, there are ongoing internal discussions to make them more coherent.
Apart from that, could you please Cc: us if you plan to submit stuff to linux-firmware?
Only Dell, the final copyright holder and product owner can submit files to linux-firmware.
Signature · 2 lines
With best wishes Dmitry
Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345
In reply to Laurentiu TudorQuoted 8 lines · Laurentiu Tudor
Hi Alex,
Quoted 5 lines · Aleksandrs Vinarskis
Quoted 3 lines · Bryan
Fascinating topic. First of all, thank you Alex for the explanation of your logic, and thank you as well for the work on the device tree for the XPS 13. I understand completely how the Dell naming/numbering scheme is confusing. The shortened version down to just the model number could also be confusing. For example, there is an XPS 9520 as well as a Latitude 9520. The 9 basically translates to "premium" not a specific line of business. For what it is worth, I would prefer the dell-xps13-9345 naming and I think we can have to be mindful to avoid a naming collision in a decade.
Quoted 8 lines
Quoted 6 lines
Hi,
Thanks for the input, it's really nice to have Dell's perspective as well. That's a good point with latitude, I was only aware of 5XXX/7XXX naming for that one... which I guess further highlights the confusing naming scheme.
Yeah, completely agree. We will raise this internally so that in the future we'll do a better job at naming platforms.
BTW, as we are discussing the new XPS, any chance that Dell might release HLOS firmware into the linux-firmware repo? In the past Lenovo did this for the X13s WoA laptop. It significantly improves Linux user experience on these laptops.
Feel free to ask if you need additional details.
Quoted 979 lines
Quoted 4 lines
I will re-spin with
dell-xps13-9345anddell,xps13-9345respectively as proposed then, unless there will be any other feedback on the V3 series before tomorrow.Great, thanks!
Couple of points:
- i'm thinking that maybe at a later point, as more dell platforms are getting added, we can re-organize the device trees, e.g. have a common 'dell-xps.dtsi' which gets inherited by specific platforms
- just noticed that the firmware paths point to something like ".../dell/tributo/...". Should we reconsider these too? Maybe something like ".../dell/xps/..." would be better?---
Thanks & Best Regards, LaurentiuQuoted 964 lines
Thanks,
AlexQuoted 961 lines
Thanks again for the support.
Bryan Kemp
Architect - Linux OS EngineeringInternal Use - Confidential
-----Original Message-----
From: Aleksandrs Vinarskis <[email protected]>
Sent: Monday, September 30, 2024 2:24 PM
To: Laurentiu Tudor <[email protected]>
Cc: Bjorn Andersson <[email protected]>; Krzysztof Kozlowski <[email protected]>; Dmitry Baryshkov <[email protected]>; [email protected]; [email protected]; [email protected]; Tudor, Laurentiu <[email protected]>; Konrad Dybcio <[email protected]>; Rob Herring <[email protected]>; Krzysztof Kozlowski <[email protected]>; Conor Dooley <[email protected]>; Rob Clark <[email protected]>; Peter de Kraker <[email protected]>; Kemp, Bryan <[email protected]>
Subject: Re: [PATCH v2 3/3] arm64: dts: qcom: Add support for X1-based Dell XPS 13 9345[EXTERNAL EMAIL]
Quoted 37 lines · Laurentiu Tudor
Hi Alex,
Thanks for this! Comment inline.
Quoted 21 lines · Aleksandrs Vinarskis
Initial support for Dell XPS 9345 13" 2024 (Tributo) based on X1E80100.
Working:
* Touchpad
* Keyboard (only post suspend&resume, i2c-hid patch WIP)
* eDP, with brightness control
* NVME
* USB Type-C ports in USB2/USB3 (one orientation)
* WiFi
* GPU/aDSP/cDSP firmware loading (requires binaries from Windows)
* Lid switch
* Sleep/suspend, nothing visibly broken on resumeNot working:
* Speakers (WIP, pin guessing, x4 WSA8845)
* Microphones (WIP, pin guessing)
* Fingerprint Reader (WIP, USB MP with ptn3222)
* USB as DP/USB3 (WIP, PS8830 based)
* Camera
* Battery InfoQuoted 8 lines
Should be working, but cannot be tested due to lack of hw:
* Higher res OLED, higher res IPS panels
* TouchscreenSigned-off-by Aleksandrs Vinarskis <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 1 + .../dts/qcom/x1e80100-dell-tributo-13.dts | 860 ++++++++++++++++++Quoted 4 lines
Could you please use the marketing name for the device tree file name & machine compatible, e.g. "
x1e80100-dell-xps13-9345.dts" for the dts file and "dell,xps13-9345" for the compat? I'm thinking that this will help people to identify it more easily.Hi,
Even though I agree that it may be easier to identify for a non-developer, I am a bit skeptical as Dell has a pretty weird naming convention which sometimes results in the name being non-unique.
In particular case - 9345 - 9 stands for XPS series, 3 stands for 13", and 45 would typically be the last digit of year + 0 (so 40), but with the introduction of last year's ''13 Plus"series they added a 5. At present, this is unique, however in 10 years it may not be.I have recently hit this issue when working on Dell XPS 15" 2024 (9530), which has the same model number as Dell XPS 15" 2013 and led to huge confusions. Only way to distinguish them is by codename ('fiorano' for the newer one), or using a complete name including the year... The codename on the other hand is easily searchable both in the source code and online.
I tried to browse the source code for existing notation, but didn't find anything strongly supporting one or another way, so decided to follow Microsoft Surface's example with codenames ('romulus').
Codenaming is also imperfect though, as in Dell's case it typically refers to chassis, rather than _the_ particular device, which typically lasts several years. Typically throughout chassis generation internals stay +/- the same, but we can't know if any of the changes would be breaking. Perhaps then,x1e80100-dell-tributo-9345anddell,tributo-9345respectively, as this would be the shortest yet most complete description? 'Tributo' already implies its XPS 13" and chassis variation (touchar, hidden trackpad etc etc), '9345' implies XPS 13" of 2024 (?) and in combination with chassis variant pinpoints the model. Otherwise, if it's strongly desired to use marketing names it can be reduced down tox1e80100-dell-9345.dtsanddell,9345altogether as
9345 implies it being both 'XPS' series and 13", and we can hope that by 2034 Dell won't repeat the same mistake with naming. Curious to hear maintainers' opinions as well.
P.S. I've sent the V3 version of the series, it probably makes sense to move this conversation there for visibility.Alex
Quoted 884 lines
---
Thanks & Best Regards, LaurentiuQuoted 879 lines
2 files changed, 861 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dtsarch/arm64/boot/dts/qcom/Makefile +1
-0@@ -271,6 +271,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e78100-lenovo-thinkpad-t14s.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-asus-vivobook-s15.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb +dtb-$(CONFIG_ARCH_QCOM) += x1e80100-dell-tributo-13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-lenovo-yoga-slim7x.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus13.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-microsoft-romulus15.dtbarch/arm64/boot/dts/qcom/x1e80100-dell-tributo-13.dts new file +853
-0@@ -0,0 +1,860 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + * Copyright (c) 2024 Aleksandrs Vinarskis +<[email protected]> */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> #include +<dt-bindings/input/input.h> #include <dt-bindings/leds/common.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +#include "x1e80100.dtsi" +#include "x1e80100-pmics.dtsi" + +/ { + model = "Dell XPS 13 9345"; + compatible = "dell,tributo-13", "qcom,x1e80100"; + chassis-type = "laptop"; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&hall_int_n_default>; + pinctrl-names = "default"; + + switch-lid { + gpios = <&tlmm 92 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + wakeup-source; + wakeup-event-action = <EV_ACT_DEASSERTED>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&cam_indicator_en>; + + led-camera-indicator { + label = "white:camera-indicator"; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_WHITE>; + gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + /* Reuse as a panic indicator until we get a "camera on" trigger */ + panic-indicator; + }; + }; + + pmic-glink { + compatible = "qcom,x1e80100-pmic-glink", + "qcom,sm8550-pmic-glink", + "qcom,pmic-glink"; + orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, + <&tlmm 123 GPIO_ACTIVE_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + /* Right-side USB Type-C port */ + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss0_hs_in: endpoint { + remote-endpoint = <&usb_1_ss0_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss0_ss_in: endpoint { + remote-endpoint = <&usb_1_ss0_qmpphy_out>; + }; + }; + }; + }; + + /* Left-side USB Type-C port */ + connector@1 { + compatible = "usb-c-connector"; + reg = <1>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss1_hs_in: endpoint { + remote-endpoint = <&usb_1_ss1_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss1_ss_in: endpoint { + remote-endpoint = <&usb_1_ss1_qmpphy_out>; + }; + }; + }; + }; + }; + + reserved-memory { + linux,cma { + compatible = "shared-dma-pool"; + size = <0x0 0x8000000>; + reusable; + linux,cma-default; + }; + }; + + vreg_edp_3p3: regulator-edp-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_EDP_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&edp_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_nvme: regulator-nvme { + compatible = "regulator-fixed"; + + regulator-name = "VREG_NVME_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&nvme_reg_en>; + pinctrl-names = "default"; + }; + + vreg_vph_pwr: regulator-vph-pwr { + compatible = "regulator-fixed"; + + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8550-rpmh-regulators"; + qcom,pmic-id = "b"; + vdd-bob1-supply = <&vreg_vph_pwr>; + vdd-bob2-supply = <&vreg_vph_pwr>; + vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; + vdd-l2-l13-l14-supply = <&vreg_bob1>; + vdd-l5-l16-supply = <&vreg_bob1>; + vdd-l6-l7-supply = <&vreg_bob2>; + vdd-l8-l9-supply = <&vreg_bob1>; + vdd-l12-supply = <&vreg_s5j_1p2>; + vdd-l15-supply = <&vreg_s4c_1p8>; + vdd-l17-supply = <&vreg_bob2>; + + vreg_bob1: bob1 { + regulator-name = "vreg_bob1"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob2: bob2 { + regulator-name = "vreg_bob2"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-name = "vreg_l2b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4b_1p8: ldo4 { + regulator-name = "vreg_l4b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p8: ldo6 { + regulator-name = "vreg_l6b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8b_3p0: ldo8 { + regulator-name = "vreg_l8b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_2p9: ldo9 { + regulator-name = "vreg_l9b_2p9"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12b_1p2: ldo12 { + regulator-name = "vreg_l12b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13b_3p0: ldo13 { + regulator-name = "vreg_l13b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14b_3p0: ldo14 { + regulator-name = "vreg_l14b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15b_1p8: ldo15 { + regulator-name = "vreg_l15b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17b_2p5: ldo17 { + regulator-name = "vreg_l17b_2p5"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "c"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s1f_0p7>; + + vreg_s4c_1p8: smps4 { + regulator-name = "vreg_s4c_1p8"; + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1c_1p2: ldo1 { + regulator-name = "vreg_l1c_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c_0p8: ldo2 { + regulator-name = "vreg_l2c_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c_0p9: ldo3 { + regulator-name = "vreg_l3c_0p9"; + regulator-min-microvolt = <920000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "d"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s4c_1p8>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_l1d_0p8: ldo1 { + regulator-name = "vreg_l1d_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2d_0p9: ldo2 { + regulator-name = "vreg_l2d_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3d_1p8: ldo3 { + regulator-name = "vreg_l3d_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-3 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "e"; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s5j_1p2>; + + vreg_l2e_0p8: ldo2 { + regulator-name = "vreg_l2e_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3e_1p2: ldo3 { + regulator-name = "vreg_l3e_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-4 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "f"; + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s5j_1p2>; + vdd-s1-supply = <&vreg_vph_pwr>; + + vreg_s1f_0p7: smps1 { + regulator-name = "vreg_s1f_0p7"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-6 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "i"; + vdd-l1-supply = <&vreg_s4c_1p8>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s1-supply = <&vreg_vph_pwr>; + vdd-s2-supply = <&vreg_vph_pwr>; + + vreg_s1i_0p9: smps1 { + regulator-name = "vreg_s1i_0p9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s2i_1p0: smps2 { + regulator-name = "vreg_s2i_1p0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1i_1p8: ldo1 { + regulator-name = "vreg_l1i_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2i_1p2: ldo2 { + regulator-name = "vreg_l2i_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3i_0p8: ldo3 { + regulator-name = "vreg_l3i_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-7 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "j"; + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s5-supply = <&vreg_vph_pwr>; + + vreg_s5j_1p2: smps5 { + regulator-name = "vreg_s5j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1j_0p9: ldo1 { + regulator-name = "vreg_l1j_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2j_1p2: ldo2 { + regulator-name = "vreg_l2j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3j_0p8: ldo3 { + regulator-name = "vreg_l3j_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&gpu { + status = "okay"; + + zap-shader { + firmware-name = "qcom/x1e80100/dell/tributo/qcdxkmsuc8380.mbn"; + }; +}; + +&i2c0 { + clock-frequency = <400000>; + status = "okay"; + + keyboard@5 { + compatible = "hid-over-i2c"; + reg = <0x5>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&kybd_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c5 { + clock-frequency = <100000>; + status = "disabled"; + /* Unknown device @0x3b */ +}; + +&i2c7 { + clock-frequency = <400000>; + status = "disabled"; + /* PS8830 Retimer @0x8 */ + /* Unknown device @0x9 */ +}; + +&i2c8 { + clock-frequency = <400000>; + + status = "okay"; + + touchscreen@0 { + compatible = "hid-over-i2c"; + reg = <0x0>; + + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&ts0_default>; + pinctrl-names = "default"; + }; +}; + +&i2c9 { + clock-frequency = <400000>; + status = "disabled"; + /* USB3 retimer device @0x4f */ }; + +&i2c17 { + clock-frequency = <400000>; + status = "okay"; + + touchpad@2c { + compatible = "hid-over-i2c"; + reg = <0x2c>; + + hid-descr-addr = <0x20>; + interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&tpad_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp3 { + compatible = "qcom,x1e80100-dp"; + /delete-property/ #sound-dai-cells; + + status = "okay"; + + aux-bus { + panel { + /* 1920x1200 IPS panel is SHP1593, PNP09FF compatible */ + compatible = "edp-panel"; + power-supply = <&vreg_edp_3p3>; + + port { + edp_panel_in: endpoint { + remote-endpoint = <&mdss_dp3_out>; + }; + }; + }; + }; + + ports { + port@1 { + reg = <1>; + + mdss_dp3_out: endpoint { + data-lanes = <0 1 2 3>; + link-frequencies = /bits/ 64 + <1620000000 2700000000 5400000000 8100000000>; + + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +}; + +&mdss_dp3_phy { + vdda-phy-supply = <&vreg_l3j_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&pcie4 { + perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&pcie4_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie4_phy { + vdda-phy-supply = <&vreg_l3i_0p8>; + vdda-pll-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&pcie6a { + perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; + + vddpe-3v3-supply = <&vreg_nvme>; + + pinctrl-0 = <&pcie6a_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie6a_phy { + vdda-phy-supply = <&vreg_l1d_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&qupv3_0 { + status = "okay"; +}; + +&qupv3_1 { + status = "okay"; +}; + +&qupv3_2 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/x1e80100/dell/tributo/qcadsp8380.mbn", + "qcom/x1e80100/dell/tributo/adsp_dtbs.elf"; + + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/x1e80100/dell/tributo/qccdsp8380.mbn", + "qcom/x1e80100/dell/tributo/cdsp_dtbs.elf"; + + status = "okay"; +}; + +&smb2360_0_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l2b_3p0>; }; + +&smb2360_1_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l14b_3p0>; }; + +&tlmm { + gpio-reserved-ranges = <44 4>, /* SPI11 (TPM) */ + <76 4>, /* SPI19 (TZ Protected) */ + <238 1>; /* UFS Reset */ + + cam_indicator_en: cam-indicator-en-state { + pins = "gpio110"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + edp_reg_en: edp-reg-en-state { + pins = "gpio70"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + hall_int_n_default: hall-int-n-state { + pins = "gpio92"; + function = "gpio"; + + bias-disable; + }; + + kybd_default: kybd-default-state { + pins = "gpio67"; + function = "gpio"; + bias-pull-up; + }; + + nvme_reg_en: nvme-reg-en-state { + pins = "gpio18"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + pcie4_default: pcie4-default-state { + clkreq-n-pins { + pins = "gpio147"; + function = "pcie4_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio146"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio148"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie6a_default: pcie6a-default-state { + clkreq-n-pins { + pins = "gpio153"; + function = "pcie6a_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio152"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio154"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + tpad_default: tpad-default-state { + disable-pins { + pins = "gpio38"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio3"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + pins = "gpio52"; + function = "gpio"; + bias-disable; + }; + }; + + ts0_default: ts0-default-state { + disable-pins { + pins = "gpio75"; + function = "gpio"; + output-high; + }; + + int-n-pins { + pins = "gpio51"; + function = "gpio"; + bias-pull-up; + }; + + reset-n-pins { + /* Technically should be High-Z input */ + pins = "gpio48"; + function = "gpio"; + output-low; + drive-strength = <2>; + }; + }; +}; + +&uart21 { + compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; + +&usb_1_ss0_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_0_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss0_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l1j_0p9>; + + status = "okay"; +}; + +&usb_1_ss0 { + status = "okay"; +}; + +&usb_1_ss0_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss0_dwc3_hs { + remote-endpoint = <&pmic_glink_ss0_hs_in>; }; + +&usb_1_ss0_qmpphy_out { + remote-endpoint = <&pmic_glink_ss0_ss_in>; }; + +&usb_1_ss1_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + phys = <&smb2360_1_eusb2_repeater>; + + status = "okay"; +}; + +&usb_1_ss1_qmpphy { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l2d_0p9>; + + status = "okay"; +}; + +&usb_1_ss1 { + status = "okay"; +}; + +&usb_1_ss1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_ss1_dwc3_hs { + remote-endpoint = <&pmic_glink_ss1_hs_in>; }; + +&usb_1_ss1_qmpphy_out { + remote-endpoint = <&pmic_glink_ss1_ss_in>; };
Signature · 2 lines
With best wishes Dmitry