fuse: remove temp page copies in writeback
Subsystems (7)
v5 cover fuse: remove temp page copies in writeback
The purpose of this patchset is to help make writeback-cache write performance in FUSE filesystems as fast as possible.
In the current FUSE writeback design (see commit 3be5a52b30aa ("fuse: support writable mmap"))), a temp page is allocated for every dirty page to be written back, the contents of the dirty page are copied over to the temp page, and the temp page gets handed to the server to write back. This is done so that writeback may be immediately cleared on the dirty page, and this in turn is done for two reasons:
a) in order to mitigate the following deadlock scenario that may arise if reclaim waits on writeback on the dirty page to complete (more details can be found in this thread [1]):
* single-threaded FUSE server is in the middle of handling a request that needs a memory allocation
* memory allocation triggers direct reclaim
* direct reclaim waits on a folio under writeback
* the FUSE server can't write back the folio since it's stuck in direct reclaim
b) in order to unblock internal (eg sync, page compaction) waits on writeback without needing the server to complete writing back to disk, which may take an indeterminate amount of time.
Allocating and copying dirty pages to temp pages is the biggest performance bottleneck for FUSE writeback. This patchset aims to get rid of the temp page altogether (which will also allow us to get rid of the internal FUSE rb tree that is needed to keep track of writeback status on the temp pages). Benchmarks show approximately a 20% improvement in throughput for 4k block-size writes and a 45% improvement for 1M block-size writes.
With removing the temp page, writeback state is now only cleared on the dirty page after the server has written it back to disk. This may take an indeterminate amount of time. As well, there is also the possibility of malicious or well-intentioned but buggy servers where writeback may in the worst case scenario, never complete. This means that any folio_wait_writeback() on a dirty page belonging to a FUSE filesystem needs to be carefully audited.
In particular, these are the cases that need to be accounted for:
* potentially deadlocking in reclaim, as mentioned above
* potentially stalling sync(2)
* potentially stalling page migration / compaction
This patchset adds a new mapping flag, AS_WRITEBACK_INDETERMINATE, which filesystems may set on its inode mappings to indicate that writeback operations may take an indeterminate amount of time to complete. FUSE will set this flag on its mappings. This patchset adds checks to the critical parts of reclaim, sync, and page migration logic where writeback may be waited on.
Please note the following:
* For sync(2), waiting on writeback will be skipped for FUSE, but this has no effect on existing behavior. Dirty FUSE pages are already not guaranteed to be written to disk by the time sync(2) returns (eg writeback is cleared on the dirty page but the server may not have written out the temp page to disk yet). If the caller wishes to ensure the data has actually been synced to disk, they should use fsync(2)/fdatasync(2) instead.
* AS_WRITEBACK_INDETERMINATE does not indicate that the folios should never be waited on when in writeback. There are some cases where the wait is desirable. For example, for the sync_file_range() syscall, it is fine to wait on the writeback since the caller passes in a fd for the operation.
[1]
https://lore.kernel.org/linux-kernel/[email protected]/
Changelog
---------
v4:
https://lore.kernel.org/linux-fsdevel/[email protected]/
Changes from v4 -> v5:
* AS_WRITEBACK_MAY_BLOCK -> AS_WRITEBACK_INDETERMINATE (Shakeel)
* Drop memory hotplug patch (David and Shakeel)
* Remove some more kunnecessary writeback waits in fuse code (Jingbo)
* Make commit message for reclaim patch more concise - drop part about deadlock and just focus on how it may stall waits
v3:
https://lore.kernel.org/linux-fsdevel/[email protected]/
Changes from v3 -> v4:
* Use filemap_fdatawait_range() instead of filemap_range_has_writeback() in readahead
v2:
https://lore.kernel.org/linux-fsdevel/[email protected]/
Changes from v2 -> v3:
* Account for sync and page migration cases as well (Miklos)
* Change AS_NO_WRITEBACK_RECLAIM to the more generic AS_WRITEBACK_MAY_BLOCK
* For fuse inodes, set mapping_writeback_may_block only if fc->writeback_cache is enabled
v1:
https://lore.kernel.org/linux-fsdevel/[email protected]/T/#t
Changes from v1 -> v2:
* Have flag in "enum mapping_flags" instead of creating asop_flags (Shakeel)
* Set fuse inodes to use AS_NO_WRITEBACK_RECLAIM (Shakeel)
Joanne Koong (5):
mm: add AS_WRITEBACK_INDETERMINATE mapping flag
mm: skip reclaiming folios in legacy memcg writeback indeterminate
contexts
fs/writeback: in wait_sb_inodes(), skip wait for
AS_WRITEBACK_INDETERMINATE mappings
mm/migrate: skip migrating folios under writeback with
AS_WRITEBACK_INDETERMINATE mappings
fuse: remove tmp folio for writebacks and internal rb tree
fs/fs-writeback.c | 3 + fs/fuse/file.c | 339 +++------------------------------------- include/linux/pagemap.h | 11 ++ mm/migrate.c | 5 +- mm/vmscan.c | 10 +- 5 files changed, 45 insertions(+), 323 deletions(-)
Signature · 1 line
2.43.5
PATCH v5 1/5 mm: add AS_WRITEBACK_INDETERMINATE mapping flag
Add a new mapping flag AS_WRITEBACK_INDETERMINATE which filesystems may set to indicate that writing back to disk may take an indeterminate amount of time to complete. Extra caution should be taken when waiting on writeback for folios belonging to mappings where this flag is set.
--- include/linux/pagemap.h | 11 +++++++++++ 1 file changed, 11 insertions(+)
include/linux/pagemap.h +11 -0
@@ -210,6 +210,7 @@ enum mapping_flags {AS_STABLE_WRITES =7 ,/* must wait for writeback before modifying folio contents */ AS_INACCESSIBLE =8 ,/* Do not attempt direct R/W access to the mapping */ +AS_WRITEBACK_INDETERMINATE =9 ,/* Use caution when waiting on writeback */ /* Bits 16-25 are used for FOLIO_ORDER */ AS_FOLIO_ORDER_BITS =5 , AS_FOLIO_ORDER_MIN = 16,
@@ -335,6 +336,16 @@ static inline bool mapping_inaccessible(struct address_space *mapping)return test_bit (AS_INACCESSIBLE , &mapping->flags); } +static inline void mapping_set_writeback_indeterminate (struct address_space *mapping) +{ +set_bit (AS_WRITEBACK_INDETERMINATE , &mapping->flags); +} + +static inline bool mapping_writeback_indeterminate (struct address_space *mapping) +{ +return test_bit (AS_WRITEBACK_INDETERMINATE , &mapping->flags); +} +static inline gfp_t mapping_gfp_mask (struct address_space * mapping) {return mapping->gfp_mask;
Signature · 1 line
2.43.5
Re: [PATCH v5 1/5] mm: add AS_WRITEBACK_INDETERMINATE mapping flag
Quoted 6 lines · Joanne Koong
Add a new mapping flag
AS_WRITEBACK_INDETERMINATEwhich filesystems may set to indicate that writing back to disk may take an indeterminate amount of time to complete. Extra caution should be taken when waiting on writeback for folios belonging to mappings where this flag is set.Signed-off-by Joanne Koong <[email protected]>
Indeterminate is definitely different, ok with me.
PATCH v5 2/5 mm: skip reclaiming folios in legacy memcg writeback indeterminate contexts
In reply to Joanne KoongCurrently in shrink_folio_list(), reclaim for folios under writeback falls into 3 different cases:
1) Reclaim is encountering an excessive number of folios under writeback and this folio has both the writeback and reclaim flags set
2) Dirty throttling is enabled (this happens if reclaim through cgroup is not enabled, if reclaim through cgroupv2 memcg is enabled, or if reclaim is on the root cgroup), or if the folio is not marked for immediate reclaim, or if the caller does not have __GFP_FS (or __GFP_IO if it's going to swap) set
3) Legacy cgroupv1 encounters a folio that already has the reclaim flag set and the caller did not have __GFP_FS (or __GFP_IO if swap) set
In cases 1) and 2), we activate the folio and skip reclaiming it while in case 3), we wait for writeback to finish on the folio and then try to reclaim the folio again. In case 3, we wait on writeback because cgroupv1 does not have dirty folio throttling, as such this is a mitigation against the case where there are too many folios in writeback with nothing else to reclaim.
For filesystems where writeback may take an indeterminate amount of time to write to disk, this has the possibility of stalling reclaim.
In this commit, if legacy memcg encounters a folio with the reclaim flag set (eg case 3) and the folio belongs to a mapping that has the AS_WRITEBACK_INDETERMINATE flag set, the folio will be activated and skip reclaim (eg default to behavior in case 2) instead.
--- mm/vmscan.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-)
mm/vmscan.c +7 -3
@@ -1129,8 +1129,9 @@ static unsigned int shrink_folio_list(struct list_head *folio_list,* 2) Global or new memcg reclaim encounters a folio that is * not marked for immediate reclaim, or the caller does not * have __GFP_FS (or __GFP_IO if it's simply going to swap, -* not to fs). In this case mark the folio for immediate -* reclaim and continue scanning. +* not to fs), or the writeback may take an indeterminate +* amount of time to complete. In this case mark the folio +* for immediate reclaim and continue scanning. * * Require may_enter_fs() because we would wait on fs, which * may not have submitted I/O yet. And the loop driver might
@@ -1155,6 +1156,8 @@ static unsigned int shrink_folio_list(struct list_head *folio_list,* takes to write them to disk. */ if (folio_test_writeback (folio)) { + mapping =folio_mapping (folio); +/* Case 1 above */ if (current_is_kswapd() && folio_test_reclaim(folio) &&
@@ -1165,7 +1168,8 @@ static unsigned int shrink_folio_list(struct list_head *folio_list,/* Case 2 above */ }else if (writeback_throttling_sane (sc) || !folio_test_reclaim (folio) || - !may_enter_fs (folio, sc->gfp_mask)) { + !may_enter_fs (folio, sc->gfp_mask) || + (mapping &&mapping_writeback_indeterminate (mapping))) {/* * This is slightly racy - * folio_end_writeback() might have
Signature · 1 line
2.43.5
PATCH v5 3/5 fs/writeback: in wait_sb_inodes(), skip wait for AS_WRITEBACK_INDETERMINATE mappings
In reply to Joanne KoongFor filesystems with the AS_WRITEBACK_INDETERMINATE flag set, writeback operations may take an indeterminate time to complete. For example, writing data back to disk in FUSE filesystems depends on the userspace server successfully completing writeback.
In this commit, wait_sb_inodes() skips waiting on writeback if the inode's mapping has AS_WRITEBACK_INDETERMINATE set, else sync(2) may take an indeterminate amount of time to complete.
If the caller wishes to ensure the data for a mapping with the AS_WRITEBACK_INDETERMINATE flag set has actually been written back to disk, they should use fsync(2)/fdatasync(2) instead.
--- fs/fs-writeback.c | 3 +++ 1 file changed, 3 insertions(+)
fs/fs-writeback.c +3 -0
@@ -2659,6 +2659,9 @@ static void wait_sb_inodes(struct super_block *sb)if (!mapping_tagged (mapping,PAGECACHE_TAG_WRITEBACK ))continue ; +if (mapping_writeback_indeterminate (mapping)) +continue ; +spin_unlock_irq (&sb->s_inode_wblist_lock);spin_lock (&inode->i_lock);
Signature · 1 line
2.43.5
Re: [PATCH v5 3/5] fs/writeback: in wait_sb_inodes(), skip wait for AS_WRITEBACK_INDETERMINATE mappings
Quoted 23 lines · Joanne Koong
For filesystems with the
AS_WRITEBACK_INDETERMINATEflag set, writeback operations may take an indeterminate time to complete. For example, writing data back to disk in FUSE filesystems depends on the userspace server successfully completing writeback.In this commit,
wait_sb_inodes()skips waiting on writeback if the inode's mapping hasAS_WRITEBACK_INDETERMINATEset, else sync(2) may take an indeterminate amount of time to complete.If the caller wishes to ensure the data for a mapping with the
AS_WRITEBACK_INDETERMINATEflag set has actually been written back to disk, they should use fsync(2)/fdatasync(2) instead.Signed-off-by Joanne Koong <[email protected]>--- fs/fs-writeback.c | 3 +++ 1 file changed, 3 insertions(+)fs/fs-writeback.c +0
-0
fs/fs-writeback.c static void wait_sb_inodes(struct super_block *sb) · line 2667
Quoted 9 lines
fs/fs-writeback.c +3
-0@@ -2659,6 +2659,9 @@ static void wait_sb_inodes(struct super_block *sb)if (!mapping_tagged (mapping,PAGECACHE_TAG_WRITEBACK ))continue ; +if (mapping_writeback_indeterminate (mapping)) +continue ; +spin_unlock_irq (&sb->s_inode_wblist_lock);spin_lock (&inode->i_lock);
Signature · 2 lines
Thanks, Jingbo
PATCH v5 4/5 mm/migrate: skip migrating folios under writeback with AS_WRITEBACK_INDETERMINATE mappings
In reply to Joanne KoongFor migrations called in MIGRATE_SYNC mode, skip migrating the folio if it is under writeback and has the AS_WRITEBACK_INDETERMINATE flag set on its mapping. If the AS_WRITEBACK_INDETERMINATE flag is set on the mapping, the writeback may take an indeterminate amount of time to complete, and waits may get stuck.
--- mm/migrate.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
mm/migrate.c +4 -1
@@ -1260,7 +1260,10 @@ static int migrate_folio_unmap(new_folio_t get_new_folio,*/ switch (mode) {case MIGRATE_SYNC : -break ; +if (!src->mapping || + !mapping_writeback_indeterminate (src->mapping)) +break ; + fallthrough;default : rc = -EBUSY ; goto out;
Signature · 1 line
2.43.5
Re: [PATCH v5 4/5] mm/migrate: skip migrating folios under writeback with AS_WRITEBACK_INDETERMINATE mappings
Quoted 7 lines · Joanne Koong
For migrations called in
MIGRATE_SYNCmode, skip migrating the folio if it is under writeback and has theAS_WRITEBACK_INDETERMINATEflag set on its mapping. If theAS_WRITEBACK_INDETERMINATEflag is set on the mapping, the writeback may take an indeterminate amount of time to complete, and waits may get stuck.Signed-off-by Joanne Koong <[email protected]>
PATCH v5 5/5 fuse: remove tmp folio for writebacks and internal rb tree
In reply to Joanne KoongIn the current FUSE writeback design (see commit 3be5a52b30aa ("fuse: support writable mmap")), a temp page is allocated for every dirty page to be written back, the contents of the dirty page are copied over to the temp page, and the temp page gets handed to the server to write back.
This is done so that writeback may be immediately cleared on the dirty page, and this in turn is done for two reasons:
a) in order to mitigate the following deadlock scenario that may arise if reclaim waits on writeback on the dirty page to complete:
* single-threaded FUSE server is in the middle of handling a request that needs a memory allocation
* memory allocation triggers direct reclaim
* direct reclaim waits on a folio under writeback
* the FUSE server can't write back the folio since it's stuck in direct reclaim
b) in order to unblock internal (eg sync, page compaction) waits on writeback without needing the server to complete writing back to disk, which may take an indeterminate amount of time.
With a recent change that added AS_WRITEBACK_INDETERMINATE and mitigates the situations described above, FUSE writeback does not need to use temp pages if it sets AS_WRITEBACK_INDETERMINATE on its inode mappings.
This commit sets AS_WRITEBACK_INDETERMINATE on the inode mappings and removes the temporary pages + extra copying and the internal rb tree.
fio benchmarks --
(using averages observed from 10 runs, throwing away outliers)
Setup:
sudo mount -t tmpfs -o size=30G tmpfs ~/tmp_mount
./libfuse/build/example/passthrough_ll -o writeback -o max_threads=4 -o source=~/tmp_mount ~/fuse_mount
fio --name=writeback --ioengine=sync --rw=write --bs={1k,4k,1M} --size=2G --numjobs=2 --ramp_time=30 --group_reporting=1 --directory=/root/fuse_mount
bs = 1k 4k 1M
Before 351 MiB/s 1818 MiB/s 1851 MiB/s After 341 MiB/s 2246 MiB/s 2685 MiB/s
% diff -3% 23% 45%
--- fs/fuse/file.c | 339 +++---------------------------------------------- 1 file changed, 20 insertions(+), 319 deletions(-)
fs/fuse/file.c +20 -319
@@ -415,89 +415,11 @@ u64 fuse_lock_owner_id(struct fuse_conn *fc, fl_owner_t id)struct fuse_writepage_args {struct fuse_io_args ia; -struct rb_node writepages_entry;struct list_head queue_entry; -struct fuse_writepage_args *next;struct inode *inode;struct fuse_sync_bucket *bucket; }; -static struct fuse_writepage_args *fuse_find_writeback (struct fuse_inode *fi, -pgoff_t idx_from,pgoff_t idx_to) -{ -struct rb_node *n; - - n = fi->writepages.rb_node; - -while (n) { -struct fuse_writepage_args *wpa; -pgoff_t curr_index; - - wpa = rb_entry(n, struct fuse_writepage_args, writepages_entry); -WARN_ON (get_fuse_inode (wpa->inode) != fi); - curr_index = wpa->ia.write.in.offset >>PAGE_SHIFT ; -if (idx_from >= curr_index + wpa->ia.ap.num_folios) - n = n->rb_right; -else if (idx_to < curr_index) - n = n->rb_left; -else -return wpa; - } -return NULL ; -} - -/* -* Check if any page in a range is under writeback -*/ -static bool fuse_range_is_writeback (struct inode *inode,pgoff_t idx_from, -pgoff_t idx_to) -{ -struct fuse_inode *fi =get_fuse_inode (inode); -bool found; - -if (RB_EMPTY_ROOT (&fi->writepages)) -return false; - -spin_lock (&fi->lock); - found =fuse_find_writeback (fi, idx_from, idx_to); -spin_unlock (&fi->lock); - -return found; -} - -static inline bool fuse_page_is_writeback (struct inode *inode,pgoff_t index) -{ -return fuse_range_is_writeback (inode, index, index); -} - -/* -* Wait for page writeback to be completed. -* -* Since fuse doesn't rely on the VM writeback tracking, this has to -* use some other means. -*/ -static void fuse_wait_on_page_writeback (struct inode *inode,pgoff_t index) -{ -struct fuse_inode *fi =get_fuse_inode (inode); - -wait_event (fi->page_waitq, !fuse_page_is_writeback (inode, index)); -} - -static inline bool fuse_folio_is_writeback (struct inode *inode, -struct folio *folio) -{ -pgoff_t last =folio_next_index (folio) -1 ; -return fuse_range_is_writeback (inode,folio_index (folio), last); -} - -static void fuse_wait_on_folio_writeback (struct inode *inode, -struct folio *folio) -{ -struct fuse_inode *fi =get_fuse_inode (inode); - -wait_event (fi->page_waitq, !fuse_folio_is_writeback (inode, folio)); -} -/* * Wait for all pending writepages on the inode to finish. *
@@ -886,13 +808,6 @@ static int fuse_do_readfolio(struct file *file, struct folio *folio)ssize_t res;u64 attr_ver; -/* -* With the temporary pages that are used to complete writeback, we can -* have writeback that extends beyond the lifetime of the folio. So -* make sure we read a properly synced folio. -*/ -fuse_wait_on_folio_writeback (inode, folio); - attr_ver =fuse_get_attr_version (fm->fc);/* Don't overflow end offset */
@@ -1003,17 +918,12 @@ static void fuse_send_readpages(struct fuse_io_args *ia, struct file *file)static void fuse_readahead (struct readahead_control *rac) {struct inode *inode = rac->mapping->host; -struct fuse_inode *fi =get_fuse_inode (inode);struct fuse_conn *fc =get_fuse_conn (inode);unsigned int max_pages, nr_pages; -pgoff_t first =readahead_index (rac); -pgoff_t last = first +readahead_count (rac) -1 ;if (fuse_is_bad (inode))return ; -wait_event (fi->page_waitq, !fuse_range_is_writeback (inode, first, last)); - max_pages = min_t(unsigned int, fc->max_pages, fc->max_read /PAGE_SIZE );
@@ -1172,7 +1082,7 @@ static ssize_t fuse_send_write_pages(struct fuse_io_args *ia,int err;for (i =0 ; i < ap->num_folios; i++) -fuse_wait_on_folio_writeback (inode, ap->folios[i]); +folio_wait_writeback (ap->folios[i]);fuse_write_args_fill (ia, ff, pos, count); ia->write.in.flags =fuse_write_flags (iocb);
@@ -1622,7 +1532,7 @@ ssize_t fuse_direct_io(struct fuse_io_priv *io, struct iov_iter *iter,return res; } } -if (!cuse &&fuse_range_is_writeback (inode, idx_from, idx_to)) { +if (!cuse &&filemap_range_has_writeback (mapping, pos, (pos + count -1 ))) {if (!write)inode_lock (inode);fuse_sync_writes (inode);
@@ -1825,7 +1735,7 @@ static void fuse_writepage_free(struct fuse_writepage_args *wpa)fuse_sync_bucket_dec (wpa->bucket);for (i =0 ; i < ap->num_folios; i++) -folio_put (ap->folios[i]); +folio_end_writeback (ap->folios[i]);fuse_file_put (wpa->ia.ff, false);
@@ -1838,7 +1748,7 @@ static void fuse_writepage_finish_stat(struct inode *inode, struct folio *folio)struct backing_dev_info *bdi =inode_to_bdi (inode);dec_wb_stat (&bdi->wb,WB_WRITEBACK ); -node_stat_sub_folio (folio,NR_WRITEBACK_TEMP ); +node_stat_sub_folio (folio,NR_WRITEBACK );wb_writeout_inc (&bdi->wb); }
@@ -1861,7 +1771,6 @@ static void fuse_send_writepage(struct fuse_mount *fm, __releases(fi->lock) __acquires(fi->lock) { -struct fuse_writepage_args *aux, *next;struct fuse_inode *fi =get_fuse_inode (wpa->inode);struct fuse_write_in *inarg = &wpa->ia.write.in;struct fuse_args *args = &wpa->ia.ap.args;
@@ -1898,19 +1807,8 @@ __acquires(fi->lock) out_free: fi->writectr--; -rb_erase (&wpa->writepages_entry, &fi->writepages);fuse_writepage_finish (wpa);spin_unlock (&fi->lock); - -/* After rb_erase() aux request list is private */ -for (aux = wpa->next; aux; aux = next) { - next = aux->next; - aux->next =NULL ; -fuse_writepage_finish_stat (aux->inode, - aux->ia.ap.folios[0 ]); -fuse_writepage_free (aux); - } -fuse_writepage_free (wpa);spin_lock (&fi->lock); }
@@ -1938,43 +1836,6 @@ __acquires(fi->lock) } } -static struct fuse_writepage_args *fuse_insert_writeback (struct rb_root *root, -struct fuse_writepage_args *wpa) -{ -pgoff_t idx_from = wpa->ia.write.in.offset >>PAGE_SHIFT ; -pgoff_t idx_to = idx_from + wpa->ia.ap.num_folios -1 ; -struct rb_node **p = &root->rb_node; -struct rb_node *parent =NULL ; - -WARN_ON (!wpa->ia.ap.num_folios); -while (*p) { -struct fuse_writepage_args *curr; -pgoff_t curr_index; - - parent = *p; - curr = rb_entry(parent, struct fuse_writepage_args, - writepages_entry); -WARN_ON (curr->inode != wpa->inode); - curr_index = curr->ia.write.in.offset >>PAGE_SHIFT ; - -if (idx_from >= curr_index + curr->ia.ap.num_folios) - p = &(*p)->rb_right; -else if (idx_to < curr_index) - p = &(*p)->rb_left; -else -return curr; - } - -rb_link_node (&wpa->writepages_entry, parent, p); -rb_insert_color (&wpa->writepages_entry, root); -return NULL ; -} - -static void tree_insert (struct rb_root *root,struct fuse_writepage_args *wpa) -{ -WARN_ON (fuse_insert_writeback (root, wpa)); -} -static void fuse_writepage_end (struct fuse_mount *fm,struct fuse_args *args,int error) {
@@ -1994,41 +1855,6 @@ static void fuse_writepage_end(struct fuse_mount *fm, struct fuse_args *args,if (!fc->writeback_cache)fuse_invalidate_attr_mask (inode,FUSE_STATX_MODIFY );spin_lock (&fi->lock); -rb_erase (&wpa->writepages_entry, &fi->writepages); -while (wpa->next) { -struct fuse_mount *fm =get_fuse_mount (inode); -struct fuse_write_in *inarg = &wpa->ia.write.in; -struct fuse_writepage_args *next = wpa->next; - - wpa->next = next->next; - next->next =NULL ; -tree_insert (&fi->writepages, next); - -/* -* Skip fuse_flush_writepages() to make it easy to crop requests -* based on primary request size. -* -* 1st case (trivial): there are no concurrent activities using -* fuse_set/release_nowrite. Then we're on safe side because -* fuse_flush_writepages() would call fuse_send_writepage() -* anyway. -* -* 2nd case: someone called fuse_set_nowrite and it is waiting -* now for completion of all in-flight requests. This happens -* rarely and no more than once per page, so this should be -* okay. -* -* 3rd case: someone (e.g. fuse_do_setattr()) is in the middle -* of fuse_set_nowrite..fuse_release_nowrite section. The fact -* that fuse_set_nowrite returned implies that all in-flight -* requests were completed along with all of their secondary -* requests. Further primary requests are blocked by negative -* writectr. Hence there cannot be any in-flight requests and -* no invocations of fuse_writepage_end() while we're in -* fuse_set_nowrite..fuse_release_nowrite section. -*/ -fuse_send_writepage (fm, next, inarg->offset + inarg->size); - } fi->writectr--;fuse_writepage_finish (wpa);spin_unlock (&fi->lock);
@@ -2115,19 +1941,17 @@ static void fuse_writepage_add_to_bucket(struct fuse_conn *fc, }static void fuse_writepage_args_page_fill (struct fuse_writepage_args *wpa,struct folio *folio, -struct folio *tmp_folio,uint32_t folio_index) +uint32_t folio_index) {struct inode *inode = folio->mapping->host;struct fuse_args_pages *ap = &wpa->ia.ap; -folio_copy (tmp_folio, folio); - - ap->folios[folio_index] = tmp_folio; + ap->folios[folio_index] = folio; ap->descs[folio_index].offset =0 ; ap->descs[folio_index].length =PAGE_SIZE ;inc_wb_stat (&inode_to_bdi (inode)->wb,WB_WRITEBACK ); -node_stat_add_folio (tmp_folio,NR_WRITEBACK_TEMP ); +node_stat_add_folio (folio,NR_WRITEBACK ); } static struct fuse_writepage_args *fuse_writepage_args_setup(struct folio *folio,
@@ -2162,18 +1986,12 @@ static int fuse_writepage_locked(struct folio *folio)struct fuse_inode *fi =get_fuse_inode (inode);struct fuse_writepage_args *wpa;struct fuse_args_pages *ap; -struct folio *tmp_folio;struct fuse_file *ff; -int error = -ENOMEM ; - - tmp_folio =folio_alloc (GFP_NOFS | __GFP_HIGHMEM,0 ); -if (!tmp_folio) - goto err; +int error = -EIO ; - error = -EIO ; ff =fuse_write_file_get (fi);if (!ff) - goto err_nofile; + goto err; wpa =fuse_writepage_args_setup (folio, ff); error = -ENOMEM ;
@@ -2184,22 +2002,17 @@ static int fuse_writepage_locked(struct folio *folio) ap->num_folios =1 ;folio_start_writeback (folio); -fuse_writepage_args_page_fill (wpa, folio, tmp_folio,0 ); +fuse_writepage_args_page_fill (wpa, folio,0 );spin_lock (&fi->lock); -tree_insert (&fi->writepages, wpa);list_add_tail (&wpa->queue_entry, &fi->queued_writes);fuse_flush_writepages (inode);spin_unlock (&fi->lock); -folio_end_writeback (folio); -return 0 ; err_writepage_args:fuse_file_put (ff, false); -err_nofile: -folio_put (tmp_folio); err:mapping_set_error (folio->mapping, error);return error;
@@ -2209,7 +2022,6 @@ struct fuse_fill_wb_data {struct fuse_writepage_args *wpa;struct fuse_file *ff;struct inode *inode; -struct folio **orig_folios;unsigned int max_folios; };
@@ -2244,69 +2056,11 @@ static void fuse_writepages_send(struct fuse_fill_wb_data *data)struct fuse_writepage_args *wpa = data->wpa;struct inode *inode = data->inode;struct fuse_inode *fi =get_fuse_inode (inode); -int num_folios = wpa->ia.ap.num_folios; -int i;spin_lock (&fi->lock);list_add_tail (&wpa->queue_entry, &fi->queued_writes);fuse_flush_writepages (inode);spin_unlock (&fi->lock); - -for (i =0 ; i < num_folios; i++) -folio_end_writeback (data->orig_folios[i]); -} - -/* -* Check under fi->lock if the page is under writeback, and insert it onto the -* rb_tree if not. Otherwise iterate auxiliary write requests, to see if there's -* one already added for a page at this offset. If there's none, then insert -* this new request onto the auxiliary list, otherwise reuse the existing one by -* swapping the new temp page with the old one. -*/ -static bool fuse_writepage_add (struct fuse_writepage_args *new_wpa, -struct folio *folio) -{ -struct fuse_inode *fi =get_fuse_inode (new_wpa->inode); -struct fuse_writepage_args *tmp; -struct fuse_writepage_args *old_wpa; -struct fuse_args_pages *new_ap = &new_wpa->ia.ap; - -WARN_ON (new_ap->num_folios !=0 ); - new_ap->num_folios =1 ; - -spin_lock (&fi->lock); - old_wpa =fuse_insert_writeback (&fi->writepages, new_wpa); -if (!old_wpa) { -spin_unlock (&fi->lock); -return true; - } - -for (tmp = old_wpa->next; tmp; tmp = tmp->next) { -pgoff_t curr_index; - -WARN_ON (tmp->inode != new_wpa->inode); - curr_index = tmp->ia.write.in.offset >>PAGE_SHIFT ; -if (curr_index == folio->index) { -WARN_ON (tmp->ia.ap.num_folios !=1 ); -swap (tmp->ia.ap.folios[0 ], new_ap->folios[0 ]); -break ; - } - } - -if (!tmp) { - new_wpa->next = old_wpa->next; - old_wpa->next = new_wpa; - } - -spin_unlock (&fi->lock); - -if (tmp) { -fuse_writepage_finish_stat (new_wpa->inode, - folio); -fuse_writepage_free (new_wpa); - } - -return false; } static bool fuse_writepage_need_send(struct fuse_conn *fc, struct folio *folio,
@@ -2315,15 +2069,6 @@ static bool fuse_writepage_need_send(struct fuse_conn *fc, struct folio *folio, {WARN_ON (!ap->num_folios); -/* -* Being under writeback is unlikely but possible. For example direct -* read to an mmaped fuse file will set the page dirty twice; once when -* the pages are faulted with get_user_pages(), and then after the read -* completed. -*/ -if (fuse_folio_is_writeback (data->inode, folio)) -return true; -/* Reached max pages */ if (ap->num_folios == fc->max_pages)return true;
@@ -2333,7 +2078,7 @@ static bool fuse_writepage_need_send(struct fuse_conn *fc, struct folio *folio,return true;/* Discontinuity */ -if (data->orig_folios[ap->num_folios -1 ]->index +1 !=folio_index (folio)) +if (ap->folios[ap->num_folios -1 ]->index +1 !=folio_index (folio))return true;/* Need to grow the pages array? If so, did the expansion fail? */
@@ -2352,7 +2097,6 @@ static int fuse_writepages_fill(struct folio *folio,struct inode *inode = data->inode;struct fuse_inode *fi =get_fuse_inode (inode);struct fuse_conn *fc =get_fuse_conn (inode); -struct folio *tmp_folio;int err;if (!data->ff) {
@@ -2367,54 +2111,23 @@ static int fuse_writepages_fill(struct folio *folio, data->wpa =NULL ; } - err = -ENOMEM ; - tmp_folio =folio_alloc (GFP_NOFS | __GFP_HIGHMEM,0 ); -if (!tmp_folio) - goto out_unlock; - -/* -* The page must not be redirtied until the writeout is completed -* (i.e. userspace has sent a reply to the write request). Otherwise -* there could be more than one temporary page instance for each real -* page. -* -* This is ensured by holding the page lock in page_mkwrite() while -* checking fuse_page_is_writeback(). We already hold the page lock -* since clear_page_dirty_for_io() and keep it held until we add the -* request to the fi->writepages list and increment ap->num_folios. -* After this fuse_page_is_writeback() will indicate that the page is -* under writeback, so we can release the page lock. -*/ if (data->wpa ==NULL ) { err = -ENOMEM ; wpa =fuse_writepage_args_setup (folio, data->ff); -if (!wpa) { -folio_put (tmp_folio); +if (!wpa) goto out_unlock; - }fuse_file_get (wpa->ia.ff); data->max_folios =1 ; ap = &wpa->ia.ap; }folio_start_writeback (folio); -fuse_writepage_args_page_fill (wpa, folio, tmp_folio, ap->num_folios); - data->orig_folios[ap->num_folios] = folio; +fuse_writepage_args_page_fill (wpa, folio, ap->num_folios); err =0 ; -if (data->wpa) { -/* -* Protected by fi->lock against concurrent access by -* fuse_page_is_writeback(). -*/ -spin_lock (&fi->lock); - ap->num_folios++; -spin_unlock (&fi->lock); - }else if (fuse_writepage_add (wpa, folio)) { + ap->num_folios++; +if (!data->wpa) data->wpa = wpa; - }else { -folio_end_writeback (folio); - } out_unlock:folio_unlock (folio);
@@ -2441,13 +2154,6 @@ static int fuse_writepages(struct address_space *mapping, data.wpa =NULL ; data.ff =NULL ; - err = -ENOMEM ; - data.orig_folios =kcalloc (fc->max_pages, -sizeof (struct folio *), -GFP_NOFS ); -if (!data.orig_folios) - goto out; - err =write_cache_pages (mapping, wbc, fuse_writepages_fill, &data);if (data.wpa) {WARN_ON (!data.wpa->ia.ap.num_folios);
@@ -2456,7 +2162,6 @@ static int fuse_writepages(struct address_space *mapping,if (data.ff)fuse_file_put (data.ff, false); -kfree (data.orig_folios); out:return err; }
@@ -2481,8 +2186,6 @@ static int fuse_write_begin(struct file *file, struct address_space *mapping,if (IS_ERR (folio)) goto error; -fuse_wait_on_page_writeback (mapping->host, folio->index); -if (folio_test_uptodate (folio) || len >=folio_size (folio)) goto success;/*
@@ -2545,13 +2248,9 @@ static int fuse_launder_folio(struct folio *folio) {int err =0 ;if (folio_clear_dirty_for_io (folio)) { -struct inode *inode = folio->mapping->host; - -/* Serialize with pending writeback for the same page */ -fuse_wait_on_page_writeback (inode, folio->index); err =fuse_writepage_locked (folio);if (!err) -fuse_wait_on_page_writeback (inode, folio->index); +folio_wait_writeback (folio); }return err; }
@@ -2595,7 +2294,7 @@ static vm_fault_t fuse_page_mkwrite(struct vm_fault *vmf)return VM_FAULT_NOPAGE ; } -fuse_wait_on_folio_writeback (inode, folio); +folio_wait_writeback (folio);return VM_FAULT_LOCKED ; }
@@ -3413,9 +3112,12 @@ static const struct address_space_operations fuse_file_aops = {void fuse_init_file_inode (struct inode *inode,unsigned int flags) {struct fuse_inode *fi =get_fuse_inode (inode); +struct fuse_conn *fc =get_fuse_conn (inode); inode->i_fop = &fuse_file_operations; inode->i_data.a_ops = &fuse_file_aops; +if (fc->writeback_cache) +mapping_set_writeback_indeterminate (&inode->i_data);INIT_LIST_HEAD (&fi->write_files);INIT_LIST_HEAD (&fi->queued_writes);
@@ -3423,7 +3125,6 @@ void fuse_init_file_inode(struct inode *inode, unsigned int flags) fi->iocachectr =0 ;init_waitqueue_head (&fi->page_waitq);init_waitqueue_head (&fi->direct_io_waitq); - fi->writepages =RB_ROOT ;if (IS_ENABLED (CONFIG_FUSE_DAX ))fuse_dax_inode_init (inode, flags);
Signature · 1 line
2.43.5
Re: [PATCH v5 5/5] fuse: remove tmp folio for writebacks and internal rb tree
fs/fuse/file.c static void fuse_writepage_finish_stat(struct inode *inode, struct folio *folio) · line 1751
Quoted 6 lines · Joanne Koong
fs/fuse/file.c +1
-1@@ -1838,7 +1748,7 @@ static void fuse_writepage_finish_stat(struct inode *inode, struct folio *folio)struct backing_dev_info *bdi =inode_to_bdi (inode);dec_wb_stat (&bdi->wb,WB_WRITEBACK ); -node_stat_sub_folio (folio,NR_WRITEBACK_TEMP ); +node_stat_sub_folio (folio,NR_WRITEBACK );
Now fuse_writepage_finish_stat() has only one caller and we could make it embedded into its only caller.
Quoted 7 lines
fs/fuse/file.c +1
-1static void fuse_writepage_args_page_fill (struct fuse_writepage_args *wpa,struct folio *folio, -struct folio *tmp_folio,uint32_t folio_index) +uint32_t folio_index) {fs/fuse/file.c +0
-0struct inode *inode = folio->mapping->host;struct fuse_args_pages *ap = &wpa->ia.ap;
fs/fuse/file.c static void fuse_writepage_add_to_bucket(struct fuse_conn *fc, · line 1954
Quoted 10 lines
fs/fuse/file.c +2
-4-folio_copy (tmp_folio, folio); - - ap->folios[folio_index] = tmp_folio; + ap->folios[folio_index] = folio; ap->descs[folio_index].offset =0 ; ap->descs[folio_index].length =PAGE_SIZE ;inc_wb_stat (&inode_to_bdi (inode)->wb,WB_WRITEBACK ); -node_stat_add_folio (tmp_folio,NR_WRITEBACK_TEMP ); +node_stat_add_folio (folio,NR_WRITEBACK );
This inc NR_WRITEBACK counter along with the corresponding dec NR_WRITEBACK counter in fuse_writepage_finish_stat() seems unnecessary, as folio_start_writeback() will increase the NR_WRITEBACK counter, while folio_end_writeback() will decrease the NR_WRITEBACK counter.
Signature · 2 lines
Thanks, Jingbo
Re: [PATCH v5 5/5] fuse: remove tmp folio for writebacks and internal rb tree
Quoted 6 lines · Jingbo Xu
Quoted 3 lines · Joanne Koong
fs/fuse/file.c +0
-0@@ -1838,7 +1748,7 @@ static void fuse_writepage_finish_stat(struct inode *inode, struct folio *folio)struct backing_dev_info *bdi =inode_to_bdi (inode);
Quoted 6 lines
fs/fuse/file.c static void fuse_writepage_finish_stat(struct inode *inode, struct folio *folio) · line 1751
Quoted 3 lines
fs/fuse/file.c +1
-1dec_wb_stat (&bdi->wb,WB_WRITEBACK ); -node_stat_sub_folio (folio,NR_WRITEBACK_TEMP ); +node_stat_sub_folio (folio,NR_WRITEBACK );Now
fuse_writepage_finish_stat()has only one caller and we could make it embedded into its only caller.
I'll make this change in v6.
Quoted 16 lines
Quoted 16 lines
fs/fuse/file.c +1
-1static void fuse_writepage_args_page_fill (struct fuse_writepage_args *wpa,struct folio *folio, -struct folio *tmp_folio,uint32_t folio_index) +uint32_t folio_index) {struct inode *inode = folio->mapping->host; struct fuse_args_pages *ap = &wpa->ia.ap;fs/fuse/file.c +1
-3-folio_copy (tmp_folio, folio); - - ap->folios[folio_index] = tmp_folio; + ap->folios[folio_index] = folio; ap->descs[folio_index].offset =0 ; ap->descs[folio_index].length =PAGE_SIZE ;
Quoted 9 lines
fs/fuse/file.c static void fuse_writepage_add_to_bucket(struct fuse_conn *fc, · line 1954
Quoted 3 lines
inc_wb_stat(&inode_to_bdi(inode)->wb, WB_WRITEBACK);fs/fuse/file.c +1
-1-node_stat_add_folio (tmp_folio,NR_WRITEBACK_TEMP ); +node_stat_add_folio (folio,NR_WRITEBACK );This inc
NR_WRITEBACKcounter along with the corresponding decNR_WRITEBACKcounter infuse_writepage_finish_stat()seems unnecessary, asfolio_start_writeback()will increase theNR_WRITEBACKcounter, whilefolio_end_writeback()will decrease theNR_WRITEBACKcounter.
Nice find, I'll make this change in v6.
Thanks,
Joanne
Quoted 4 lines
--
Thanks,
Jingbo
Re: [PATCH v5 5/5] fuse: remove tmp folio for writebacks and internal rb tree
In reply to Joanne KoongQuoted 192 lines · Joanne Koong
In the current FUSE writeback design (see commit
3be5a52b30aa("fuse: support writable mmap")), a temp page is allocated for every dirty page to be written back, the contents of the dirty page are copied over to the temp page, and the temp page gets handed to the server to write back.This is done so that writeback may be immediately cleared on the dirty page, and this in turn is done for two reasons:
a) in order to mitigate the following deadlock scenario that may arise if reclaim waits on writeback on the dirty page to complete:
* single-threaded FUSE server is in the middle of handling a request that needs a memory allocation
* memory allocation triggers direct reclaim
* direct reclaim waits on a folio under writeback
* the FUSE server can't write back the folio since it's stuck in direct reclaim
b) in order to unblock internal (eg sync, page compaction) waits on writeback without needing the server to complete writing back to disk, which may take an indeterminate amount of time.With a recent change that added
AS_WRITEBACK_INDETERMINATEand mitigates the situations described above, FUSE writeback does not need to use temp pages if it setsAS_WRITEBACK_INDETERMINATEon its inode mappings.This commit sets
AS_WRITEBACK_INDETERMINATEon the inode mappings and removes the temporary pages + extra copying and the internal rb tree.fio benchmarks --
(using averages observed from 10 runs, throwing away outliers)Setup:
sudo mount -t tmpfs -o size=30G tmpfs ~/tmp_mount
./libfuse/build/example/passthrough_ll -o writeback -o max_threads=4 -o source=~/tmp_mount ~/fuse_mountfio --name=writeback --ioengine=sync --rw=write --bs={1k,4k,1M} --size=2G --numjobs=2 --ramp_time=30 --group_reporting=1 --directory=/root/fuse_mount
bs = 1k 4k 1M
Before 351 MiB/s 1818 MiB/s 1851 MiB/s After 341 MiB/s 2246 MiB/s 2685 MiB/s% diff -3% 23% 45%
Signed-off-by Joanne Koong <[email protected]>--- fs/fuse/file.c | 339 +++---------------------------------------------- 1 file changed, 20 insertions(+), 319 deletions(-)fs/fuse/file.c +2
-92@@ -415,89 +415,11 @@ u64 fuse_lock_owner_id(struct fuse_conn *fc, fl_owner_t id)struct fuse_writepage_args {struct fuse_io_args ia; -struct rb_node writepages_entry;struct list_head queue_entry; -struct fuse_writepage_args *next;struct inode *inode;struct fuse_sync_bucket *bucket; }; -static struct fuse_writepage_args *fuse_find_writeback (struct fuse_inode *fi, -pgoff_t idx_from,pgoff_t idx_to) -{ -struct rb_node *n; - - n = fi->writepages.rb_node; - -while (n) { -struct fuse_writepage_args *wpa; -pgoff_t curr_index; - - wpa = rb_entry(n, struct fuse_writepage_args, writepages_entry); -WARN_ON (get_fuse_inode (wpa->inode) != fi); - curr_index = wpa->ia.write.in.offset >>PAGE_SHIFT ; -if (idx_from >= curr_index + wpa->ia.ap.num_folios) - n = n->rb_right; -else if (idx_to < curr_index) - n = n->rb_left; -else -return wpa; - } -return NULL ; -} - -/* -* Check if any page in a range is under writeback -*/ -static bool fuse_range_is_writeback (struct inode *inode,pgoff_t idx_from, -pgoff_t idx_to) -{ -struct fuse_inode *fi =get_fuse_inode (inode); -bool found; - -if (RB_EMPTY_ROOT (&fi->writepages)) -return false; - -spin_lock (&fi->lock); - found =fuse_find_writeback (fi, idx_from, idx_to); -spin_unlock (&fi->lock); - -return found; -} - -static inline bool fuse_page_is_writeback (struct inode *inode,pgoff_t index) -{ -return fuse_range_is_writeback (inode, index, index); -} - -/* -* Wait for page writeback to be completed. -* -* Since fuse doesn't rely on the VM writeback tracking, this has to -* use some other means. -*/ -static void fuse_wait_on_page_writeback (struct inode *inode,pgoff_t index) -{ -struct fuse_inode *fi =get_fuse_inode (inode); - -wait_event (fi->page_waitq, !fuse_page_is_writeback (inode, index)); -} - -static inline bool fuse_folio_is_writeback (struct inode *inode, -struct folio *folio) -{ -pgoff_t last =folio_next_index (folio) -1 ; -return fuse_range_is_writeback (inode,folio_index (folio), last); -} - -static void fuse_wait_on_folio_writeback (struct inode *inode, -struct folio *folio) -{ -struct fuse_inode *fi =get_fuse_inode (inode); - -wait_event (fi->page_waitq, !fuse_folio_is_writeback (inode, folio)); -} -/* * Wait for all pending writepages on the inode to finish. * @@ -886,13 +808,6 @@ static int fuse_do_readfolio(struct file *file, struct folio *folio)ssize_t res;u64 attr_ver; -/* -* With the temporary pages that are used to complete writeback, we can -* have writeback that extends beyond the lifetime of the folio. So -* make sure we read a properly synced folio. -*/ -fuse_wait_on_folio_writeback (inode, folio); - attr_ver =fuse_get_attr_version (fm->fc);/* Don't overflow end offset */ @@ -1003,17 +918,12 @@ static void fuse_send_readpages(struct fuse_io_args *ia, struct file *file)static void fuse_readahead (struct readahead_control *rac) {struct inode *inode = rac->mapping->host; -struct fuse_inode *fi =get_fuse_inode (inode);struct fuse_conn *fc =get_fuse_conn (inode);unsigned int max_pages, nr_pages; -pgoff_t first =readahead_index (rac); -pgoff_t last = first +readahead_count (rac) -1 ;if (fuse_is_bad (inode))return ; -wait_event (fi->page_waitq, !fuse_range_is_writeback (inode, first, last)); - max_pages = min_t(unsigned int, fc->max_pages, fc->max_read /PAGE_SIZE );@@ -1172,7 +1082,7 @@ static ssize_t fuse_send_write_pages(struct fuse_io_args *ia,int err;for (i =0 ; i < ap->num_folios; i++) -fuse_wait_on_folio_writeback (inode, ap->folios[i]); +folio_wait_writeback (ap->folios[i]);fuse_write_args_fill (ia, ff, pos, count); ia->write.in.flags =fuse_write_flags (iocb);@@ -1622,7 +1532,7 @@ ssize_t fuse_direct_io(struct fuse_io_priv *io, struct iov_iter *iter,return res; } } -if (!cuse &&fuse_range_is_writeback (inode, idx_from, idx_to)) { +if (!cuse &&filemap_range_has_writeback (mapping, pos, (pos + count -1 ))) {if (!write)inode_lock (inode);fuse_sync_writes (inode);
fs/fuse/file.c static void fuse_writepage_free(struct fuse_writepage_args *wpa) · line 1738
Quoted 5 lines
fs/fuse/file.c +1
-1@@ -1825,7 +1735,7 @@ static void fuse_writepage_free(struct fuse_writepage_args *wpa)fuse_sync_bucket_dec (wpa->bucket);for (i =0 ; i < ap->num_folios; i++) -folio_put (ap->folios[i]); +folio_end_writeback (ap->folios[i]);
I noticed that if we folio_end_writeback() in fuse_writepage_finish() (rather than fuse_writepage_free()), there's ~50% buffer write bandwridth performance gain (5500MB -> 8500MB)[*]
The fuse server is generally implemented in multi-thread style, and multi (fuse server) worker threads could fetch and process FUSE_WRITE requests of one fuse inode. Then there's serious lock contention for the xarray lock (of the address space) when these multi worker threads call fuse_writepage_end->folio_end_writeback when they are sending replies of FUSE_WRITE requests.
The lock contention is greatly alleviated when folio_end_writeback() is serialized with fi->lock. IOWs in the current implementation (folio_end_writeback() in fuse_writepage_free()), each worker thread needs to compete for the xarray lock for 256 times (one fuse request can contain at most 256 pages if FUSE_MAX_MAX_PAGES is 256) when completing a FUSE_WRITE request.
After moving folio_end_writeback() to fuse_writepage_finish(), each worker thread needs to compete for fi->lock only once. IOWs the locking granularity is larger now.
Quoted 25 lines
fs/fuse/file.c +0
-18@@ -2367,54 +2111,23 @@ static int fuse_writepages_fill(struct folio *folio, data->wpa =NULL ; } - err = -ENOMEM ; - tmp_folio =folio_alloc (GFP_NOFS | __GFP_HIGHMEM,0 ); -if (!tmp_folio) - goto out_unlock; - -/* -* The page must not be redirtied until the writeout is completed -* (i.e. userspace has sent a reply to the write request). Otherwise -* there could be more than one temporary page instance for each real -* page. -* -* This is ensured by holding the page lock in page_mkwrite() while -* checking fuse_page_is_writeback(). We already hold the page lock -* since clear_page_dirty_for_io() and keep it held until we add the -* request to the fi->writepages list and increment ap->num_folios. -* After this fuse_page_is_writeback() will indicate that the page is -* under writeback, so we can release the page lock. -*/ if (data->wpa ==NULL ) { err = -ENOMEM ; wpa =fuse_writepage_args_setup (folio, data->ff);
fs/fuse/file.c static int fuse_writepages_fill(struct folio *folio, · line 2123
Quoted 10 lines
fs/fuse/file.c +1
-3-if (!wpa) { -folio_put (tmp_folio); +if (!wpa) goto out_unlock; - }fuse_file_get (wpa->ia.ff); data->max_folios =1 ; ap = &wpa->ia.ap; }folio_start_writeback (folio);
There's also a lock contention for the xarray lock when calling folio_start_writeback().
I also noticed a strange thing that, if we lock fi->lock and unlock immediately, the write bandwidth improves by 5% (8500MB -> 9000MB). The palce where to insert the "locking fi->lock and unlocking" actually doesn't matter. "perf lock contention" shows the lock contention for the xarray lock is greatly alleviated, though I can't understand how it is done quite well...
As the performance gain is not significant (~5%), I think we can leave this stange phenomenon aside for now.
[*] test case:
./passthrough_hp --bypass-rw 2 /tmp /mnt (testbench mode in
https://github.com/libfuse/libfuse/pull/807/commits/e83789cc6e83ca42ccc9899c4f7f8c69f31cbff9
bypass the buffer copy along with the persistence procedure)
fio -fallocate=0 -numjobs=32 -iodepth=1 -ioengine=sync -sync=0 --direct=0 -rw=write -bs=1M -size=100G --time_based --runtime=300 -directory=/mnt/ --group_reporting --name=Fio
Signature · 2 lines
Thanks, Jingbo
Re: [PATCH v5 5/5] fuse: remove tmp folio for writebacks and internal rb tree
Quoted 96 lines · Jingbo Xu
Quoted 70 lines · Joanne Koong
In the current FUSE writeback design (see commit
3be5a52b30aa("fuse: support writable mmap")), a temp page is allocated for every dirty page to be written back, the contents of the dirty page are copied over to the temp page, and the temp page gets handed to the server to write back.This is done so that writeback may be immediately cleared on the dirty page, and this in turn is done for two reasons:
a) in order to mitigate the following deadlock scenario that may arise if reclaim waits on writeback on the dirty page to complete:
* single-threaded FUSE server is in the middle of handling a request that needs a memory allocation
* memory allocation triggers direct reclaim
* direct reclaim waits on a folio under writeback
* the FUSE server can't write back the folio since it's stuck in direct reclaim
b) in order to unblock internal (eg sync, page compaction) waits on writeback without needing the server to complete writing back to disk, which may take an indeterminate amount of time.With a recent change that added
AS_WRITEBACK_INDETERMINATEand mitigates the situations described above, FUSE writeback does not need to use temp pages if it setsAS_WRITEBACK_INDETERMINATEon its inode mappings.This commit sets
AS_WRITEBACK_INDETERMINATEon the inode mappings and removes the temporary pages + extra copying and the internal rb tree.fio benchmarks --
(using averages observed from 10 runs, throwing away outliers)Setup:
sudo mount -t tmpfs -o size=30G tmpfs ~/tmp_mount
./libfuse/build/example/passthrough_ll -o writeback -o max_threads=4 -o source=~/tmp_mount ~/fuse_mountfio --name=writeback --ioengine=sync --rw=write --bs={1k,4k,1M} --size=2G --numjobs=2 --ramp_time=30 --group_reporting=1 --directory=/root/fuse_mount
bs = 1k 4k 1M
Before 351 MiB/s 1818 MiB/s 1851 MiB/s After 341 MiB/s 2246 MiB/s 2685 MiB/s% diff -3% 23% 45%
Signed-off-by Joanne Koong <[email protected]>--- fs/fuse/file.c | 339 +++---------------------------------------------- 1 file changed, 20 insertions(+), 319 deletions(-)fs/fuse/file.c +2
-2@@ -1172,7 +1082,7 @@ static ssize_t fuse_send_write_pages(struct fuse_io_args *ia,int err;for (i =0 ; i < ap->num_folios; i++) -fuse_wait_on_folio_writeback (inode, ap->folios[i]); +folio_wait_writeback (ap->folios[i]);fuse_write_args_fill (ia, ff, pos, count); ia->write.in.flags =fuse_write_flags (iocb);@@ -1622,7 +1532,7 @@ ssize_t fuse_direct_io(struct fuse_io_priv *io, struct iov_iter *iter,return res; } } -if (!cuse &&fuse_range_is_writeback (inode, idx_from, idx_to)) { +if (!cuse &&filemap_range_has_writeback (mapping, pos, (pos + count -1 ))) {if (!write)inode_lock (inode);fuse_sync_writes (inode);fs/fuse/file.c static void fuse_writepage_free(struct fuse_writepage_args *wpa) · line 1738
Quoted 5 lines
fs/fuse/file.c +1
-1@@ -1825,7 +1735,7 @@ static void fuse_writepage_free(struct fuse_writepage_args *wpa)fuse_sync_bucket_dec (wpa->bucket);for (i =0 ; i < ap->num_folios; i++) -folio_put (ap->folios[i]); +folio_end_writeback (ap->folios[i]);I noticed that if we
folio_end_writeback()infuse_writepage_finish()(rather thanfuse_writepage_free()), there's ~50% buffer write bandwridth performance gain (5500MB -> 8500MB)[*]The fuse server is generally implemented in multi-thread style, and multi (fuse server) worker threads could fetch and process
FUSE_WRITErequests of one fuse inode. Then there's serious lock contention for the xarray lock (of the address space) when these multi worker threads callfuse_writepage_end->folio_end_writebackwhen they are sending replies ofFUSE_WRITErequests.The lock contention is greatly alleviated when
folio_end_writeback()is serialized withfi->lock. IOWs in the current implementation (folio_end_writeback()infuse_writepage_free()), each worker thread needs to compete for the xarray lock for 256 times (one fuse request can contain at most 256 pages ifFUSE_MAX_MAX_PAGESis 256) when completing aFUSE_WRITErequest.
Quoted 4 lines
After moving
folio_end_writeback()tofuse_writepage_finish(), each worker thread needs to compete forfi->lockonly once. IOWs the locking granularity is larger now.
Interesting! Thanks for sharing. Are you able to consistently repro these results and on different machines? When I run it locally on my machine using the commands you shared, I'm seeing roughly the same throughput:
Current implementation (folio_end_writeback() in fuse_writepage_free()):
WRITE: bw=385MiB/s (404MB/s), 385MiB/s-385MiB/s (404MB/s-404MB/s),
io=113GiB (121GB), run=300177-300177msec
WRITE: bw=384MiB/s (403MB/s), 384MiB/s-384MiB/s (403MB/s-403MB/s),
io=113GiB (121GB), run=300178-300178msec
fuse_end_writeback() in fuse_writepage_finish():
WRITE: bw=387MiB/s (406MB/s), 387MiB/s-387MiB/s (406MB/s-406MB/s),
io=113GiB (122GB), run=300165-300165msec
WRITE: bw=381MiB/s (399MB/s), 381MiB/s-381MiB/s (399MB/s-399MB/s),
io=112GiB (120GB), run=300143-300143msec
I wonder if it's because your machine is so much faster that lock contention makes a difference for you whereas on my machine there's other things that slow it down before lock contention comes into play.
I see your point about why it would make sense that having folio_end_writeback() in fuse_writepage_finish() inside the scope of the fi->lock could make it faster, but I also could see how having it outside the lock could make it faster as well. I'm thinking about the scenario where if there's 8 threads all executing fuse_send_writepage() at the same time, calling folio_end_writeback() outside the fi->lock would unblock other threads trying to get the fi->lock and that other thread could execute while folio_end_writeback() gets executed.
Looking at it some more, it seems like it'd be useful if there was some equivalent api to folio_end_writeback() that takes in an array of folios and would only need to grab the xarray lock once to clear writeback on all the folios in the array.
When fuse supports large folios [*] this will help lock contention on the xarray lock as well because there'll be less folio_end_writeback() calls.
I'm happy to move the fuse_end_writeback() call to fuse_writepage_finish() considering what you're seeing. 5500 Mb -> 8800 Mb is a huge perf improvement!
[*] https://lore.kernel.org/linux-fsdevel/[email protected]/
Quoted 41 lines
Quoted 27 lines
fs/fuse/file.c +0
-18@@ -2367,54 +2111,23 @@ static int fuse_writepages_fill(struct folio *folio, data->wpa =NULL ; } - err = -ENOMEM ; - tmp_folio =folio_alloc (GFP_NOFS | __GFP_HIGHMEM,0 ); -if (!tmp_folio) - goto out_unlock; - -/* -* The page must not be redirtied until the writeout is completed -* (i.e. userspace has sent a reply to the write request). Otherwise -* there could be more than one temporary page instance for each real -* page. -* -* This is ensured by holding the page lock in page_mkwrite() while -* checking fuse_page_is_writeback(). We already hold the page lock -* since clear_page_dirty_for_io() and keep it held until we add the -* request to the fi->writepages list and increment ap->num_folios. -* After this fuse_page_is_writeback() will indicate that the page is -* under writeback, so we can release the page lock. -*/ if (data->wpa ==NULL ) { err = -ENOMEM ; wpa =fuse_writepage_args_setup (folio, data->ff);fs/fuse/file.c static int fuse_writepages_fill(struct folio *folio, · line 2123
Quoted 10 lines
fs/fuse/file.c +1
-3-if (!wpa) { -folio_put (tmp_folio); +if (!wpa) goto out_unlock; - }fuse_file_get (wpa->ia.ff); data->max_folios =1 ; ap = &wpa->ia.ap; }folio_start_writeback (folio);There's also a lock contention for the xarray lock when calling
folio_start_writeback().
Quoted 2 lines
I also noticed a strange thing that, if we lock
fi->lockand unlock immediately, the write bandwidth improves by 5% (8500MB -> 9000MB). The
Interesting! By lock fi->lock and unlock immediately, do you mean locking it, then unlocking it, then calling folio_start_writeback() or locking it, calling folio_start_writeback() and then unlocking it?
Thanks,
Joanne
Quoted 22 lines
palce where to insert the "locking
fi->lockand unlocking" actually doesn't matter. "perf lock contention" shows the lock contention for the xarray lock is greatly alleviated, though I can't understand how it is done quite well...As the performance gain is not significant (~5%), I think we can leave this stange phenomenon aside for now.
[*] test case:
./passthrough_hp --bypass-rw 2 /tmp /mnt (testbench mode in
https://github.com/libfuse/libfuse/pull/807/commits/e83789cc6e83ca42ccc9899c4f7f8c69f31cbff9
bypass the buffer copy along with the persistence procedure)fio -fallocate=0 -numjobs=32 -iodepth=1 -ioengine=sync -sync=0 --direct=0 -rw=write -bs=1M -size=100G --time_based --runtime=300 -directory=/mnt/ --group_reporting --name=Fio
--
Thanks,
Jingbo
Re: [PATCH v5 5/5] fuse: remove tmp folio for writebacks and internal rb tree
Quoted 119 lines · Joanne Koong
Quoted 96 lines · Jingbo Xu
Quoted 70 lines · Joanne Koong
In the current FUSE writeback design (see commit
3be5a52b30aa("fuse: support writable mmap")), a temp page is allocated for every dirty page to be written back, the contents of the dirty page are copied over to the temp page, and the temp page gets handed to the server to write back.This is done so that writeback may be immediately cleared on the dirty page, and this in turn is done for two reasons:
a) in order to mitigate the following deadlock scenario that may arise if reclaim waits on writeback on the dirty page to complete:
* single-threaded FUSE server is in the middle of handling a request that needs a memory allocation
* memory allocation triggers direct reclaim
* direct reclaim waits on a folio under writeback
* the FUSE server can't write back the folio since it's stuck in direct reclaim
b) in order to unblock internal (eg sync, page compaction) waits on writeback without needing the server to complete writing back to disk, which may take an indeterminate amount of time.With a recent change that added
AS_WRITEBACK_INDETERMINATEand mitigates the situations described above, FUSE writeback does not need to use temp pages if it setsAS_WRITEBACK_INDETERMINATEon its inode mappings.This commit sets
AS_WRITEBACK_INDETERMINATEon the inode mappings and removes the temporary pages + extra copying and the internal rb tree.fio benchmarks --
(using averages observed from 10 runs, throwing away outliers)Setup:
sudo mount -t tmpfs -o size=30G tmpfs ~/tmp_mount
./libfuse/build/example/passthrough_ll -o writeback -o max_threads=4 -o source=~/tmp_mount ~/fuse_mountfio --name=writeback --ioengine=sync --rw=write --bs={1k,4k,1M} --size=2G --numjobs=2 --ramp_time=30 --group_reporting=1 --directory=/root/fuse_mount
bs = 1k 4k 1M
Before 351 MiB/s 1818 MiB/s 1851 MiB/s After 341 MiB/s 2246 MiB/s 2685 MiB/s% diff -3% 23% 45%
Signed-off-by Joanne Koong <[email protected]>--- fs/fuse/file.c | 339 +++---------------------------------------------- 1 file changed, 20 insertions(+), 319 deletions(-)fs/fuse/file.c +2
-2@@ -1172,7 +1082,7 @@ static ssize_t fuse_send_write_pages(struct fuse_io_args *ia,int err;for (i =0 ; i < ap->num_folios; i++) -fuse_wait_on_folio_writeback (inode, ap->folios[i]); +folio_wait_writeback (ap->folios[i]);fuse_write_args_fill (ia, ff, pos, count); ia->write.in.flags =fuse_write_flags (iocb);@@ -1622,7 +1532,7 @@ ssize_t fuse_direct_io(struct fuse_io_priv *io, struct iov_iter *iter,return res; } } -if (!cuse &&fuse_range_is_writeback (inode, idx_from, idx_to)) { +if (!cuse &&filemap_range_has_writeback (mapping, pos, (pos + count -1 ))) {if (!write)inode_lock (inode);fuse_sync_writes (inode);fs/fuse/file.c static void fuse_writepage_free(struct fuse_writepage_args *wpa) · line 1738
Quoted 5 lines
fs/fuse/file.c +1
-1@@ -1825,7 +1735,7 @@ static void fuse_writepage_free(struct fuse_writepage_args *wpa)fuse_sync_bucket_dec (wpa->bucket);for (i =0 ; i < ap->num_folios; i++) -folio_put (ap->folios[i]); +folio_end_writeback (ap->folios[i]);I noticed that if we
folio_end_writeback()infuse_writepage_finish()(rather thanfuse_writepage_free()), there's ~50% buffer write bandwridth performance gain (5500MB -> 8500MB)[*]The fuse server is generally implemented in multi-thread style, and multi (fuse server) worker threads could fetch and process
FUSE_WRITErequests of one fuse inode. Then there's serious lock contention for the xarray lock (of the address space) when these multi worker threads callfuse_writepage_end->folio_end_writebackwhen they are sending replies ofFUSE_WRITErequests.The lock contention is greatly alleviated when
folio_end_writeback()is serialized withfi->lock. IOWs in the current implementation (folio_end_writeback()infuse_writepage_free()), each worker thread needs to compete for the xarray lock for 256 times (one fuse request can contain at most 256 pages ifFUSE_MAX_MAX_PAGESis 256) when completing aFUSE_WRITErequest.Quoted 4 lines
After moving
folio_end_writeback()tofuse_writepage_finish(), each worker thread needs to compete forfi->lockonly once. IOWs the locking granularity is larger now.Interesting! Thanks for sharing. Are you able to consistently repro these results and on different machines? When I run it locally on my machine using the commands you shared, I'm seeing roughly the same throughput:
Current implementation (
folio_end_writeback()infuse_writepage_free()):
WRITE: bw=385MiB/s (404MB/s), 385MiB/s-385MiB/s (404MB/s-404MB/s),
io=113GiB (121GB), run=300177-300177msec
WRITE: bw=384MiB/s (403MB/s), 384MiB/s-384MiB/s (403MB/s-403MB/s),
io=113GiB (121GB), run=300178-300178msec
fuse_end_writeback()infuse_writepage_finish():
WRITE: bw=387MiB/s (406MB/s), 387MiB/s-387MiB/s (406MB/s-406MB/s),
io=113GiB (122GB), run=300165-300165msec
WRITE: bw=381MiB/s (399MB/s), 381MiB/s-381MiB/s (399MB/s-399MB/s),
io=112GiB (120GB), run=300143-300143msec
Quoted 3 lines
I wonder if it's because your machine is so much faster that lock contention makes a difference for you whereas on my machine there's other things that slow it down before lock contention comes into play.
Yeah, I agree that the lock contention matters only when the writeback kworker consumes 100% CPU, i.e. when the writeback kworker is the bottleneck. To expose that, the passthrough_hp daemon works in benchmark[*] mode (I noticed that passthrough_hp can be the bottleneck when disabling "--bypass-rw" mode).
[*]
https://github.com/libfuse/libfuse/pull/807/commits/e83789cc6e83ca42ccc9899c4f7f8c69f31cbff9
Quoted 11 lines
I see your point about why it would make sense that having
folio_end_writeback()infuse_writepage_finish()inside the scope of thefi->lockcould make it faster, but I also could see how having it outside the lock could make it faster as well. I'm thinking about the scenario where if there's 8 threads all executingfuse_send_writepage()at the same time, callingfolio_end_writeback()outside thefi->lockwould unblock other threads trying to get thefi->lockand that other thread could execute whilefolio_end_writeback()gets executed.
Quoted 4 lines
Looking at it some more, it seems like it'd be useful if there was some equivalent api to
folio_end_writeback()that takes in an array of folios and would only need to grab the xarray lock once to clear writeback on all the folios in the array.
Yes it's exactly what we need.
Quoted 4 lines
When fuse supports large folios [*] this will help lock contention on the xarray lock as well because there'll be less
folio_end_writeback()calls.
Cool, it definitely helps.
Quoted 4 lines
I'm happy to move the
fuse_end_writeback()call tofuse_writepage_finish()considering what you're seeing. 5500 Mb -> 8800 Mb is a huge perf improvement!
This statistics is tested in benchmark ("--bypass-rw") mode. When disabling "--bypass-rw" mode and testing fuse passthrough_hp over a ext4 over nvme, the performance gain is ~10% (4009MB/s ->4428MB/s).
Quoted 39 lines
Quoted 39 lines
Quoted 25 lines
fs/fuse/file.c +0
-18@@ -2367,54 +2111,23 @@ static int fuse_writepages_fill(struct folio *folio, data->wpa =NULL ; } - err = -ENOMEM ; - tmp_folio =folio_alloc (GFP_NOFS | __GFP_HIGHMEM,0 ); -if (!tmp_folio) - goto out_unlock; - -/* -* The page must not be redirtied until the writeout is completed -* (i.e. userspace has sent a reply to the write request). Otherwise -* there could be more than one temporary page instance for each real -* page. -* -* This is ensured by holding the page lock in page_mkwrite() while -* checking fuse_page_is_writeback(). We already hold the page lock -* since clear_page_dirty_for_io() and keep it held until we add the -* request to the fi->writepages list and increment ap->num_folios. -* After this fuse_page_is_writeback() will indicate that the page is -* under writeback, so we can release the page lock. -*/ if (data->wpa ==NULL ) { err = -ENOMEM ; wpa =fuse_writepage_args_setup (folio, data->ff);fs/fuse/file.c static int fuse_writepages_fill(struct folio *folio, · line 2123
Quoted 10 lines
fs/fuse/file.c +1
-3-if (!wpa) { -folio_put (tmp_folio); +if (!wpa) goto out_unlock; - }fuse_file_get (wpa->ia.ff); data->max_folios =1 ; ap = &wpa->ia.ap; }folio_start_writeback (folio);There's also a lock contention for the xarray lock when calling
folio_start_writeback().
Quoted 6 lines
Quoted 2 lines
I also noticed a strange thing that, if we lock
fi->lockand unlock immediately, the write bandwidth improves by 5% (8500MB -> 9000MB). TheInteresting! By lock
fi->lockand unlock immediately, do you mean locking it, then unlocking it, then callingfolio_start_writeback()or locking it, callingfolio_start_writeback()and then unlocking it?
Either way works, as long as we lock/unlock fi->lock in fuse_writepages_fill()... The lock contention is further alleviated when folio_start_writeback() is inside the critical area of fi->lock.
Signature · 2 lines
Thanks, Jingbo
Re: [PATCH v5 5/5] fuse: remove tmp folio for writebacks and internal rb tree
Quoted 164 lines · Jingbo Xu
Quoted 119 lines · Joanne Koong
Quoted 96 lines · Jingbo Xu
Quoted 70 lines · Joanne Koong
In the current FUSE writeback design (see commit
3be5a52b30aa("fuse: support writable mmap")), a temp page is allocated for every dirty page to be written back, the contents of the dirty page are copied over to the temp page, and the temp page gets handed to the server to write back.This is done so that writeback may be immediately cleared on the dirty page, and this in turn is done for two reasons:
a) in order to mitigate the following deadlock scenario that may arise if reclaim waits on writeback on the dirty page to complete:
* single-threaded FUSE server is in the middle of handling a request that needs a memory allocation
* memory allocation triggers direct reclaim
* direct reclaim waits on a folio under writeback
* the FUSE server can't write back the folio since it's stuck in direct reclaim
b) in order to unblock internal (eg sync, page compaction) waits on writeback without needing the server to complete writing back to disk, which may take an indeterminate amount of time.With a recent change that added
AS_WRITEBACK_INDETERMINATEand mitigates the situations described above, FUSE writeback does not need to use temp pages if it setsAS_WRITEBACK_INDETERMINATEon its inode mappings.This commit sets
AS_WRITEBACK_INDETERMINATEon the inode mappings and removes the temporary pages + extra copying and the internal rb tree.fio benchmarks --
(using averages observed from 10 runs, throwing away outliers)Setup:
sudo mount -t tmpfs -o size=30G tmpfs ~/tmp_mount
./libfuse/build/example/passthrough_ll -o writeback -o max_threads=4 -o source=~/tmp_mount ~/fuse_mountfio --name=writeback --ioengine=sync --rw=write --bs={1k,4k,1M} --size=2G --numjobs=2 --ramp_time=30 --group_reporting=1 --directory=/root/fuse_mount
bs = 1k 4k 1M
Before 351 MiB/s 1818 MiB/s 1851 MiB/s After 341 MiB/s 2246 MiB/s 2685 MiB/s% diff -3% 23% 45%
Signed-off-by Joanne Koong <[email protected]>--- fs/fuse/file.c | 339 +++---------------------------------------------- 1 file changed, 20 insertions(+), 319 deletions(-)fs/fuse/file.c +2
-2@@ -1172,7 +1082,7 @@ static ssize_t fuse_send_write_pages(struct fuse_io_args *ia,int err;for (i =0 ; i < ap->num_folios; i++) -fuse_wait_on_folio_writeback (inode, ap->folios[i]); +folio_wait_writeback (ap->folios[i]);fuse_write_args_fill (ia, ff, pos, count); ia->write.in.flags =fuse_write_flags (iocb);@@ -1622,7 +1532,7 @@ ssize_t fuse_direct_io(struct fuse_io_priv *io, struct iov_iter *iter,return res; } } -if (!cuse &&fuse_range_is_writeback (inode, idx_from, idx_to)) { +if (!cuse &&filemap_range_has_writeback (mapping, pos, (pos + count -1 ))) {if (!write)inode_lock (inode);fuse_sync_writes (inode);fs/fuse/file.c static void fuse_writepage_free(struct fuse_writepage_args *wpa) · line 1738
Quoted 5 lines
fs/fuse/file.c +1
-1@@ -1825,7 +1735,7 @@ static void fuse_writepage_free(struct fuse_writepage_args *wpa)fuse_sync_bucket_dec (wpa->bucket);for (i =0 ; i < ap->num_folios; i++) -folio_put (ap->folios[i]); +folio_end_writeback (ap->folios[i]);I noticed that if we
folio_end_writeback()infuse_writepage_finish()(rather thanfuse_writepage_free()), there's ~50% buffer write bandwridth performance gain (5500MB -> 8500MB)[*]The fuse server is generally implemented in multi-thread style, and multi (fuse server) worker threads could fetch and process
FUSE_WRITErequests of one fuse inode. Then there's serious lock contention for the xarray lock (of the address space) when these multi worker threads callfuse_writepage_end->folio_end_writebackwhen they are sending replies ofFUSE_WRITErequests.The lock contention is greatly alleviated when
folio_end_writeback()is serialized withfi->lock. IOWs in the current implementation (folio_end_writeback()infuse_writepage_free()), each worker thread needs to compete for the xarray lock for 256 times (one fuse request can contain at most 256 pages ifFUSE_MAX_MAX_PAGESis 256) when completing aFUSE_WRITErequest.Quoted 4 lines
After moving
folio_end_writeback()tofuse_writepage_finish(), each worker thread needs to compete forfi->lockonly once. IOWs the locking granularity is larger now.Interesting! Thanks for sharing. Are you able to consistently repro these results and on different machines? When I run it locally on my machine using the commands you shared, I'm seeing roughly the same throughput:
Current implementation (
folio_end_writeback()infuse_writepage_free()):
WRITE: bw=385MiB/s (404MB/s), 385MiB/s-385MiB/s (404MB/s-404MB/s),
io=113GiB (121GB), run=300177-300177msec
WRITE: bw=384MiB/s (403MB/s), 384MiB/s-384MiB/s (403MB/s-403MB/s),
io=113GiB (121GB), run=300178-300178msec
fuse_end_writeback()infuse_writepage_finish():
WRITE: bw=387MiB/s (406MB/s), 387MiB/s-387MiB/s (406MB/s-406MB/s),
io=113GiB (122GB), run=300165-300165msec
WRITE: bw=381MiB/s (399MB/s), 381MiB/s-381MiB/s (399MB/s-399MB/s),
io=112GiB (120GB), run=300143-300143msecQuoted 3 lines
I wonder if it's because your machine is so much faster that lock contention makes a difference for you whereas on my machine there's other things that slow it down before lock contention comes into play.
Yeah, I agree that the lock contention matters only when the writeback kworker consumes 100% CPU, i.e. when the writeback kworker is the bottleneck. To expose that, the
passthrough_hpdaemon works in benchmark[*] mode (I noticed thatpassthrough_hpcan be the bottleneck when disabling "--bypass-rw" mode).[*]
https://github.com/libfuse/libfuse/pull/807/commits/e83789cc6e83ca42ccc9899c4f7f8c69f31cbff9Quoted 11 lines
I see your point about why it would make sense that having
folio_end_writeback()infuse_writepage_finish()inside the scope of thefi->lockcould make it faster, but I also could see how having it outside the lock could make it faster as well. I'm thinking about the scenario where if there's 8 threads all executingfuse_send_writepage()at the same time, callingfolio_end_writeback()outside thefi->lockwould unblock other threads trying to get thefi->lockand that other thread could execute whilefolio_end_writeback()gets executed.Quoted 4 lines
Looking at it some more, it seems like it'd be useful if there was some equivalent api to
folio_end_writeback()that takes in an array of folios and would only need to grab the xarray lock once to clear writeback on all the folios in the array.Yes it's exactly what we need.
Quoted 4 lines
When fuse supports large folios [*] this will help lock contention on the xarray lock as well because there'll be less
folio_end_writeback()calls.Cool, it definitely helps.
Quoted 1 line
Quoted 7 lines
Quoted 3 lines
I'm happy to move the
fuse_end_writeback()call tofuse_writepage_finish()considering what you're seeing. 5500 Mb -> 8800 Mb is a huge perf improvement!This statistics is tested in benchmark ("--bypass-rw") mode. When disabling "--bypass-rw" mode and testing fuse
passthrough_hpover a ext4 over nvme, the performance gain is ~10% (4009MB/s ->4428MB/s).
Thanks for Jingbo and Joanne for looking into this! In typical HPC case one expects currently >15GB/s for a single client - Infiniband RDMA and possibly multi rail. The --bypass-rw is rather close to that.
Thanks,
Bernd