Enable ESMs and related PMIC
cover Enable ESMs and related PMIC
This enables the ESMs and the associated PMIC.
Programming these bits is a requirement to make the watchdog actually reset the board.
Patch 3/3 is already available in upstream kernel. While above sync is done, sending this series as RFC.
Logs
https://gist.github.com/uditkumarti/5dca3fcb2ebe2535f9c9c719ee625513
For reset https://gist.github.com/uditkumarti/5dca3fcb2ebe2535f9c9c719ee625513#file-gistfile1-txt-L2475
Gowtham Tammana (1):
arm: dts: k3-j7200: Add ESM PMIC support for tps659413
Neha Malcom Francis (1):
configs: j7200_evm_r5: Add ESM related configs for J7200
Udit Kumar (1):
arm: dts: k3-j7200: Add bootph for esm and pmic nodes
arch/arm/dts/k3-j7200-r5-common-proc-board.dts | 15 +++++++++++++++ configs/j7200_evm_r5_defconfig | 2 ++ 2 files changed, 17 insertions(+)
Signature · 1 line
2.34.1
RFC PATCH 1/3 configs: j7200_evm_r5: Add ESM related configs for J7200
From: Neha Malcom Francis <[email protected]>
Add CONFIG_ESM_K3 and CONFIG_ESM_PMIC to enable ESM initialization in J7200.
--- configs/j7200_evm_r5_defconfig | 2 ++ 1 file changed, 2 insertions(+)
configs/j7200_evm_r5_defconfig +2 -0
@@ -101,7 +101,9 @@ CONFIG_DM_MAILBOX=y CONFIG_K3_SEC_PROXY=y CONFIG_FS_LOADER=y CONFIG_SPL_FS_LOADER=y +CONFIG_ESM_K3=y CONFIG_K3_AVS0=y +CONFIG_ESM_PMIC=y CONFIG_SUPPORT_EMMC_BOOT=y CONFIG_SPL_MMC_HS400_SUPPORT=y CONFIG_MMC_SDHCI=y
Signature · 1 line
2.34.1
RFC PATCH 2/3 arm: dts: k3-j7200: Add ESM PMIC support for tps659413
In reply to Udit KumarFrom: Gowtham Tammana <[email protected]>
On J7200 processor board MCU_SAFETY_ERROR signal is routed to PMIC for ESM error handling. The PMIC resets the board on receipt of the signal. Enable the support for the board by adding ESM PMIC node.
--- arch/arm/dts/k3-j7200-r5-common-proc-board.dts | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm/dts/k3-j7200-r5-common-proc-board.dts +7 -0
@@ -108,3 +108,10 @@ vdd-supply-2 = <&buckb1>; bootph-pre-ram; }; + +&tps659414 { + esm: esm { + compatible = "ti,tps659413-esm"; + bootph-pre-ram; + }; +};
Signature · 1 line
2.34.1
RFC PATCH 3/3 arm: dts: k3-j7200: Add bootph for esm and pmic nodes
In reply to Udit KumarIn order to get esm and pmic probed by R5 SPL, these nodes should be have bootph pre ram property.
However these changes are committed in kernel with following sha-id b903ab269e67 (arm64: dts: ti: k3-j7200: Add bootph-* properties) and bdb543b1664b (arm64: dts: ti: k3-j7200-evm*: Add bootph-* properties).
While we wait for above committed to get synched with u-boot. Meanwhile add bootph in these nodes.
--- arch/arm/dts/k3-j7200-r5-common-proc-board.dts | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/arm/dts/k3-j7200-r5-common-proc-board.dts +8 -0
@@ -115,3 +115,11 @@ bootph-pre-ram; }; }; + +&bucka1 { + bootph-pre-ram; +}; + +&main_esm { + bootph-pre-ram; +};
Signature · 1 line
2.34.1