Skip to contentSkip to conversation

arm64: dts: rockchip: sync dts with schematic for Radxa ROCK 5B

PATCH In review FUKAUMI Naoki 2 participants 9 messages Nov 30, 2024 – Dec 2, 2024

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover arm64: dts: rockchip: sync dts with schematic for Radxa ROCK 5B

this patch series fixes regulators, pmic, pwm-fan, and rtc to match with schematic[1]. some missing info is taken from vendor kernel[2].

in addition to above, convert heartbeat LED to "pwm-led" to control brightness.

this patch series depend on following patch:
"arm64: dts: rockchip: rename rfkill label for Radxa ROCK 5B"
https://patchwork.kernel.org/project/linux-rockchip/patch/[email protected]/

[1] https://dl.radxa.com/rock5/5b/docs/hw/radxa_rock_5b_v1450_schematic.pdf
[2] https://github.com/radxa/kernel

FUKAUMI Naoki (6):
arm64: dts: rockchip: fix regulators for Radxa ROCK 5B
arm64: dts: rockchip: add regulator for NPU for Radxa ROCK 5B
arm64: dts: rockchip: fix pmic regulators for Radxa ROCK 5B
arm64: dts: rockchip: convert leds node to "pwm-led" for Radxa ROCK 5B
arm64: dts: rockchip: fix pwm-fan node for Radxa ROCK 5B
arm64: dts: rockchip: fix rtc node for Radxa ROCK 5B

 .../boot/dts/rockchip/rk3588-rock-5b.dts      | 247 ++++++++++--------
 1 file changed, 138 insertions(+), 109 deletions(-)
Signature · 7 lines
2.43.0


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#1 lore raw

PATCH 1/6 arm64: dts: rockchip: fix regulators for Radxa ROCK 5B

fix regulator and pin names to match with schematic. regulator for USB ports are unnamed, so I referred schematic for Radxa ROCK 5B+.

add missing "typec_vin" and "vcc4v0_sys" regulator, and add missing "phy-supply" for "pcie30phy" and "u2phy1_otg". remove now unused and non-existent "vcc3v3_pcie2x1l2" regulator.

remove "regulator-always-on" and "regulator-boot-on" from regulators which is turned on by consumer.

---
 .../boot/dts/rockchip/rk3588-rock-5b.dts      | 106 ++++++++++--------
 1 file changed, 57 insertions(+), 49 deletions(-)
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts +57 -49
index d597112f1d5b..727a5880d87a 100644
@@ -84,54 +84,59 @@ rfkill-bt {
 		shutdown-gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_HIGH>;
 	};
 
-	vcc3v3_pcie2x1l0: regulator-vcc3v3-pcie2x1l0 {
+	typec_vin: regulator-typec-vin {
 		compatible = "regulator-fixed";
-		enable-active-high;
-		gpios = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pcie2_0_vcc3v3_en>;
-		regulator-name = "vcc3v3_pcie2x1l0";
+		regulator-name = "typec_vin";
 		regulator-always-on;
 		regulator-boot-on;
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		startup-delay-us = <50000>;
-		vin-supply = <&vcc5v0_sys>;
 	};
 
-	vcc3v3_pcie2x1l2: regulator-vcc3v3-pcie2x1l2 {
+	vcc3v3_wf: regulator-vcc3v3-wf {
 		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3_pcie2x1l2";
+		enable-active-high;
+		gpios = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ekey_en>;
+		regulator-name = "vcc3v3_wf";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		startup-delay-us = <5000>;
-		vin-supply = <&vcc_3v3_s3>;
+		startup-delay-us = <50000>;
+		vin-supply = <&vcc5v0_sys>;
 	};
 
-	vcc3v3_pcie30: regulator-vcc3v3-pcie30 {
+	/* pi6c pcie clock generator */
+	vcc3v3_pi6c_05: vcc3v3_pcie30: regulator-vcc3v3-pi6c-05 {
 		compatible = "regulator-fixed";
 		enable-active-high;
 		gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&pcie3_vcc3v3_en>;
-		regulator-name = "vcc3v3_pcie30";
+		pinctrl-0 = <&pcie30x4_pwren_h>;
+		regulator-name = "vcc3v3_pi6c_05";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		startup-delay-us = <5000>;
 		vin-supply = <&vcc5v0_sys>;
 	};
 
-	vcc5v0_host: regulator-vcc5v0-host {
+	vcc4v0_sys: regulator-vcc4v0-sys {
 		compatible = "regulator-fixed";
-		regulator-name = "vcc5v0_host";
-		regulator-boot-on;
+		regulator-name = "vcc4v0_sys";
 		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <4000000>;
+		regulator-max-microvolt = <4000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v_usb: regulator-vcc5v-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v_usb";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		enable-active-high;
 		gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&vcc5v0_host_en>;
+		pinctrl-0 = <&usb_host_pwren_h>;
 		vin-supply = <&vcc5v0_sys>;
 	};
 
@@ -142,6 +147,7 @@ vcc5v0_sys: regulator-vcc5v0-sys {
 		regulator-boot-on;
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
+		vin-supply = <&typec_vin>;
 	};
 
 	vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
@@ -151,7 +157,7 @@ vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
 		regulator-boot-on;
 		regulator-min-microvolt = <1100000>;
 		regulator-max-microvolt = <1100000>;
-		vin-supply = <&vcc5v0_sys>;
+		vin-supply = <&vcc4v0_sys>;
 	};
 };
 
@@ -239,7 +245,7 @@ vdd_cpu_big0_s0: regulator@42 {
 		regulator-min-microvolt = <550000>;
 		regulator-max-microvolt = <1050000>;
 		regulator-ramp-delay = <2300>;
-		vin-supply = <&vcc5v0_sys>;
+		vin-supply = <&vcc4v0_sys>;
 
 		regulator-state-mem {
 			regulator-off-in-suspend;
@@ -256,7 +262,7 @@ vdd_cpu_big1_s0: regulator@43 {
 		regulator-min-microvolt = <550000>;
 		regulator-max-microvolt = <1050000>;
 		regulator-ramp-delay = <2300>;
-		vin-supply = <&vcc5v0_sys>;
+		vin-supply = <&vcc4v0_sys>;
 
 		regulator-state-mem {
 			regulator-off-in-suspend;
@@ -350,27 +356,28 @@ map1 {
 
 &pcie2x1l0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pcie2_0_rst>;
+	pinctrl-0 = <&pcie30x1_0_perstn_m1_l>;
 	reset-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
-	vpcie3v3-supply = <&vcc3v3_pcie2x1l0>;
+	vpcie3v3-supply = <&vcc3v3_wf>;
 	status = "okay";
 };
 
 &pcie2x1l2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pcie2_2_rst>;
+	pinctrl-0 = <&pcie_perst_l>;
 	reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_HIGH>;
-	vpcie3v3-supply = <&vcc3v3_pcie2x1l2>;
+	vpcie3v3-supply = <&vcc_3v3_s3>;
 	status = "okay";
 };
 
 &pcie30phy {
+	phy-supply = <&vcc3v3_pi6c_05>;
 	status = "okay";
 };
 
 &pcie3x4 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pcie3_rst>;
+	pinctrl-0 = <&pcie30x4_perstn_m1_l>;
 	reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
 	vpcie3v3-supply = <&vcc3v3_pcie30>;
 	status = "okay";
@@ -396,31 +403,31 @@ hp_detect: hp-detect {
 	};
 
 	pcie2 {
-		pcie2_0_rst: pcie2-0-rst {
+		pcie30x1_0_perstn_m1_l: pcie30x1-0-perstn-m1-l {
 			rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 
-		pcie2_0_vcc3v3_en: pcie2-0-vcc-en {
+		ekey_en: ekey-en {
 			rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 
-		pcie2_2_rst: pcie2-2-rst {
+		pcie_perst_l: pcie-perst-l {
 			rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
 
 	pcie3 {
-		pcie3_rst: pcie3-rst {
+		pcie30x4_perstn_m1_l: pcie30x4-perstn-m1-l {
 			rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 
-		pcie3_vcc3v3_en: pcie3-vcc3v3-en {
+		pcie30x4_pwren_h: pcie30x4-pwren-h {
 			rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
 
 	usb {
-		vcc5v0_host_en: vcc5v0-host-en {
+		usb_host_pwren_h: usb-host-pwren-h {
 			rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
@@ -474,7 +481,7 @@ &sdio {
 	sd-uhs-sdr25;
 	sd-uhs-sdr50;
 	sd-uhs-sdr104;
-	vmmc-supply = <&vcc3v3_pcie2x1l0>;
+	vmmc-supply = <&vcc3v3_wf>;
 	vqmmc-supply = <&vcc_1v8_s3>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdiom0_pins>;
@@ -523,21 +530,21 @@ pmic@0 {
 
 		system-power-controller;
 
-		vcc1-supply = <&vcc5v0_sys>;
-		vcc2-supply = <&vcc5v0_sys>;
-		vcc3-supply = <&vcc5v0_sys>;
-		vcc4-supply = <&vcc5v0_sys>;
-		vcc5-supply = <&vcc5v0_sys>;
-		vcc6-supply = <&vcc5v0_sys>;
-		vcc7-supply = <&vcc5v0_sys>;
-		vcc8-supply = <&vcc5v0_sys>;
-		vcc9-supply = <&vcc5v0_sys>;
-		vcc10-supply = <&vcc5v0_sys>;
+		vcc1-supply = <&vcc4v0_sys>;
+		vcc2-supply = <&vcc4v0_sys>;
+		vcc3-supply = <&vcc4v0_sys>;
+		vcc4-supply = <&vcc4v0_sys>;
+		vcc5-supply = <&vcc4v0_sys>;
+		vcc6-supply = <&vcc4v0_sys>;
+		vcc7-supply = <&vcc4v0_sys>;
+		vcc8-supply = <&vcc4v0_sys>;
+		vcc9-supply = <&vcc4v0_sys>;
+		vcc10-supply = <&vcc4v0_sys>;
 		vcc11-supply = <&vcc_2v0_pldo_s3>;
-		vcc12-supply = <&vcc5v0_sys>;
+		vcc12-supply = <&vcc4v0_sys>;
 		vcc13-supply = <&vcc_1v1_nldo_s3>;
 		vcc14-supply = <&vcc_1v1_nldo_s3>;
-		vcca-supply = <&vcc5v0_sys>;
+		vcca-supply = <&vcc4v0_sys>;
 
 		gpio-controller;
 		#gpio-cells = <2>;
@@ -840,6 +847,7 @@ &u2phy1 {
 };
 
 &u2phy1_otg {
+	phy-supply = <&vcc5v_usb>;
 	status = "okay";
 };
 
@@ -858,7 +866,7 @@ &u2phy3 {
 };
 
 &u2phy3_host {
-	phy-supply = <&vcc5v0_host>;
+	phy-supply = <&vcc5v_usb>;
 	status = "okay";
 };
 
Signature · 7 lines
2.43.0


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#2 lore raw

PATCH 2/6 arm64: dts: rockchip: add regulator for NPU for Radxa ROCK 5B

In reply to FUKAUMI Naoki

add "vdd_vpu_s0" regulator for NPU.

---
 .../boot/dts/rockchip/rk3588-rock-5b.dts      | 23 +++++++++++++++++++
 1 file changed, 23 insertions(+)
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts +23 -0
index 727a5880d87a..3cd8c63151db 100644
@@ -270,6 +270,29 @@ regulator-state-mem {
 	};
 };
 
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1m2_xfer>;
+	status = "okay";
+
+	vdd_npu_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_npu_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <950000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc4v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
 &i2c6 {
 	status = "okay";
 
Signature · 7 lines
2.43.0


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#3 lore raw

PATCH 3/6 arm64: dts: rockchip: fix pmic regulators for Radxa ROCK 5B

In reply to FUKAUMI Naoki

fix regulator names to match with schematic. fix properties to match with vendor kernel.

---
 .../boot/dts/rockchip/rk3588-rock-5b.dts      | 80 +++++++++----------
 1 file changed, 40 insertions(+), 40 deletions(-)
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts +40 -40
index 3cd8c63151db..95f2f4dbf12d 100644
@@ -461,7 +461,7 @@ &pwm1 {
 };
 
 &saradc {
-	vref-supply = <&avcc_1v8_s0>;
+	vref-supply = <&vcca_1v8_s0>;
 	status = "okay";
 };
 
@@ -588,12 +588,12 @@ rk806_dvs3_null: dvs3-null-pins {
 		};
 
 		regulators {
-			vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
+			vdd_gpu_s0: dcdc-reg1 {
+				regulator-name = "vdd_gpu_s0";
 				regulator-boot-on;
 				regulator-min-microvolt = <550000>;
 				regulator-max-microvolt = <950000>;
 				regulator-ramp-delay = <12500>;
-				regulator-name = "vdd_gpu_s0";
 				regulator-enable-ramp-delay = <400>;
 
 				regulator-state-mem {
@@ -601,13 +601,13 @@ regulator-state-mem {
 				};
 			};
 
-			vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
+			vdd_cpu_lit_s0: dcdc-reg2 {
+				regulator-name = "vdd_cpu_lit_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <550000>;
 				regulator-max-microvolt = <950000>;
 				regulator-ramp-delay = <12500>;
-				regulator-name = "vdd_cpu_lit_s0";
 
 				regulator-state-mem {
 					regulator-off-in-suspend;
@@ -615,26 +615,26 @@ regulator-state-mem {
 			};
 
 			vdd_log_s0: dcdc-reg3 {
+				regulator-name = "vdd_log_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <675000>;
 				regulator-max-microvolt = <750000>;
 				regulator-ramp-delay = <12500>;
-				regulator-name = "vdd_log_s0";
 
 				regulator-state-mem {
-					regulator-off-in-suspend;
+					regulator-on-in-suspend;
 					regulator-suspend-microvolt = <750000>;
 				};
 			};
 
-			vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 {
+			vdd_vdenc_s0: dcdc-reg4 {
+				regulator-name = "vdd_vdenc_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <550000>;
 				regulator-max-microvolt = <950000>;
 				regulator-ramp-delay = <12500>;
-				regulator-name = "vdd_vdenc_s0";
 
 				regulator-state-mem {
 					regulator-off-in-suspend;
@@ -642,12 +642,12 @@ regulator-state-mem {
 			};
 
 			vdd_ddr_s0: dcdc-reg5 {
+				regulator-name = "vdd_ddr_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <675000>;
 				regulator-max-microvolt = <900000>;
 				regulator-ramp-delay = <12500>;
-				regulator-name = "vdd_ddr_s0";
 
 				regulator-state-mem {
 					regulator-off-in-suspend;
@@ -656,9 +656,9 @@ regulator-state-mem {
 			};
 
 			vdd2_ddr_s3: dcdc-reg6 {
+				regulator-name = "vdd2_ddr_s3";
 				regulator-always-on;
 				regulator-boot-on;
-				regulator-name = "vdd2_ddr_s3";
 
 				regulator-state-mem {
 					regulator-on-in-suspend;
@@ -666,12 +666,11 @@ regulator-state-mem {
 			};
 
 			vcc_2v0_pldo_s3: dcdc-reg7 {
+				regulator-name = "vcc_2v0_pldo_s3";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <2000000>;
 				regulator-max-microvolt = <2000000>;
-				regulator-ramp-delay = <12500>;
-				regulator-name = "vdd_2v0_pldo_s3";
 
 				regulator-state-mem {
 					regulator-on-in-suspend;
@@ -680,11 +679,11 @@ regulator-state-mem {
 			};
 
 			vcc_3v3_s3: dcdc-reg8 {
+				regulator-name = "vcc_3v3_s3";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
-				regulator-name = "vcc_3v3_s3";
 
 				regulator-state-mem {
 					regulator-on-in-suspend;
@@ -693,9 +692,9 @@ regulator-state-mem {
 			};
 
 			vddq_ddr_s0: dcdc-reg9 {
+				regulator-name = "vddq_ddr_s0";
 				regulator-always-on;
 				regulator-boot-on;
-				regulator-name = "vddq_ddr_s0";
 
 				regulator-state-mem {
 					regulator-off-in-suspend;
@@ -703,11 +702,11 @@ regulator-state-mem {
 			};
 
 			vcc_1v8_s3: dcdc-reg10 {
+				regulator-name = "vcc_1v8_s3";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
-				regulator-name = "vcc_1v8_s3";
 
 				regulator-state-mem {
 					regulator-on-in-suspend;
@@ -715,63 +714,63 @@ regulator-state-mem {
 				};
 			};
 
-			avcc_1v8_s0: pldo-reg1 {
+			vcca_1v8_s0: pldo-reg1 {
+				regulator-name = "vcca_1v8_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
-				regulator-name = "avcc_1v8_s0";
 
 				regulator-state-mem {
-					regulator-off-in-suspend;
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
 				};
 			};
 
 			vcc_1v8_s0: pldo-reg2 {
+				regulator-name = "vcc_1v8_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
-				regulator-name = "vcc_1v8_s0";
 
 				regulator-state-mem {
-					regulator-off-in-suspend;
+					regulator-on-in-suspend;
 					regulator-suspend-microvolt = <1800000>;
 				};
 			};
 
-			avdd_1v2_s0: pldo-reg3 {
+			vdda_1v2_s0: pldo-reg3 {
+				regulator-name = "vdda_1v2_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1200000>;
-				regulator-name = "avdd_1v2_s0";
 
 				regulator-state-mem {
 					regulator-off-in-suspend;
 				};
 			};
 
-			vcc_3v3_s0: pldo-reg4 {
+			vcca_3v3_s0: pldo-reg4 {
+				regulator-name = "vcca_3v3_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
-				regulator-ramp-delay = <12500>;
-				regulator-name = "vcc_3v3_s0";
 
 				regulator-state-mem {
-					regulator-off-in-suspend;
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
 				};
 			};
 
 			vccio_sd_s0: pldo-reg5 {
+				regulator-name = "vccio_sd_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
-				regulator-ramp-delay = <12500>;
-				regulator-name = "vccio_sd_s0";
 
 				regulator-state-mem {
 					regulator-off-in-suspend;
@@ -779,11 +778,11 @@ regulator-state-mem {
 			};
 
 			pldo6_s3: pldo-reg6 {
+				regulator-name = "pldo6_s3";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
-				regulator-name = "pldo6_s3";
 
 				regulator-state-mem {
 					regulator-on-in-suspend;
@@ -792,11 +791,11 @@ regulator-state-mem {
 			};
 
 			vdd_0v75_s3: nldo-reg1 {
+				regulator-name = "vdd_0v75_s3";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <750000>;
 				regulator-max-microvolt = <750000>;
-				regulator-name = "vdd_0v75_s3";
 
 				regulator-state-mem {
 					regulator-on-in-suspend;
@@ -804,37 +803,38 @@ regulator-state-mem {
 				};
 			};
 
-			vdd_ddr_pll_s0: nldo-reg2 {
+			vdda_ddr_pll_s0: nldo-reg2 {
+				regulator-name = "vdda_ddr_pll_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <850000>;
-				regulator-name = "vdd_ddr_pll_s0";
 
 				regulator-state-mem {
-					regulator-off-in-suspend;
+					regulator-on-in-suspend;
 					regulator-suspend-microvolt = <850000>;
 				};
 			};
 
-			avdd_0v75_s0: nldo-reg3 {
+			vdda_0v75_s0: nldo-reg3 {
+				regulator-name = "vdda_0v75_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <750000>;
 				regulator-max-microvolt = <750000>;
-				regulator-name = "avdd_0v75_s0";
 
 				regulator-state-mem {
-					regulator-off-in-suspend;
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <750000>;
 				};
 			};
 
-			vdd_0v85_s0: nldo-reg4 {
+			vdda_0v85_s0: nldo-reg4 {
+				regulator-name = "vdda_0v85_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <850000>;
-				regulator-name = "vdd_0v85_s0";
 
 				regulator-state-mem {
 					regulator-off-in-suspend;
@@ -842,11 +842,11 @@ regulator-state-mem {
 			};
 
 			vdd_0v75_s0: nldo-reg5 {
+				regulator-name = "vdd_0v75_s0";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <750000>;
 				regulator-max-microvolt = <750000>;
-				regulator-name = "vdd_0v75_s0";
 
 				regulator-state-mem {
 					regulator-off-in-suspend;
Signature · 7 lines
2.43.0


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#4 lore raw

PATCH 4/6 arm64: dts: rockchip: convert leds node to "pwm-led" for Radxa ROCK 5B

In reply to FUKAUMI Naoki

convert heartbeat LED to use "pwm-led" to control birghtness. also, define default-state = "on" to match with U-Boot.

---
 .../boot/dts/rockchip/rk3588-rock-5b.dts      | 22 +++++++++----------
 1 file changed, 10 insertions(+), 12 deletions(-)
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts +10 -12
index 95f2f4dbf12d..7c8359fe712a 100644
@@ -50,15 +50,15 @@ hdmi0_con_in: endpoint {
 	};
 
 	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_rgb_b>;
+		compatible = "pwm-leds";
 
-		led_rgb_b {
-			function = LED_FUNCTION_STATUS;
+		led-0 {
 			color = <LED_COLOR_ID_BLUE>;
-			gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			function = LED_FUNCTION_STATUS;
 			linux,default-trigger = "heartbeat";
+			pwms = <&pwm0 0 1000000 0>;
+			max-brightness = <255>;
 		};
 	};
 
@@ -413,12 +413,6 @@ hym8563_int: hym8563-int {
 		};
 	};
 
-	leds {
-		led_rgb_b: led-rgb-b {
-			rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
-		};
-	};
-
 	sound {
 		hp_detect: hp-detect {
 			rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
@@ -456,6 +450,10 @@ usb_host_pwren_h: usb-host-pwren-h {
 	};
 };
 
+&pwm0 {
+	status = "okay";
+};
+
 &pwm1 {
 	status = "okay";
 };
Signature · 7 lines
2.43.0


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#5 lore raw

PATCH 5/6 arm64: dts: rockchip: fix pwm-fan node for Radxa ROCK 5B

In reply to FUKAUMI Naoki

fix properties to match with vendor kernel.

---
 arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts +3 -3
index 7c8359fe712a..6a02febaefb7 100644
@@ -64,10 +64,10 @@ led-0 {
 
 	fan: pwm-fan {
 		compatible = "pwm-fan";
-		cooling-levels = <0 120 150 180 210 240 255>;
-		fan-supply = <&vcc5v0_sys>;
-		pwms = <&pwm1 0 50000 0>;
 		#cooling-cells = <2>;
+		cooling-levels = <0 64 128 192 255>;
+		fan-supply = <&vcc5v0_sys>;
+		pwms = <&pwm1 0 60000 0>;
 	};
 
 	rfkill {
Signature · 7 lines
2.43.0


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#6 lore raw

Re: [PATCH 5/6] arm64: dts: rockchip: fix pwm-fan node for Radxa ROCK 5B

Hi Naoki,

Quoted 13 lines · FUKAUMI Naoki

fix properties to match with vendor kernel.

---
 arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts +0 -0
index 7c8359fe712a..6a02febaefb7 100644

arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts led-0 { · line 68

Quoted 8 lines
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts +1 -3
@@ -64,10 +64,10 @@ led-0 {
 
        fan: pwm-fan {
                compatible = "pwm-fan";
-               cooling-levels = <0 120 150 180 210 240 255>;
-               fan-supply = <&vcc5v0_sys>;
-               pwms = <&pwm1 0 50000 0>;
                #cooling-cells = <2>;
+               cooling-levels = <0 64 128 192 255>;

Could you please share your testing setup for this part? In my experience using Radxa 4010 fan, it didn't spin up reliably below 120, so the value of 64 looks not helpful here.

Best regards,
Alexey

#7 lore raw

Re: [PATCH 5/6] arm64: dts: rockchip: fix pwm-fan node for Radxa ROCK 5B

Hi Alexey Charkov,

Quoted 17 lines · Alexey Charkov

Hi Naoki,

Quoted 14 lines · FUKAUMI Naoki

fix properties to match with vendor kernel.

---
  arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts | 6 +++---
  1 file changed, 3 insertions(+), 3 deletions(-)
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts +0 -0
index 7c8359fe712a..6a02febaefb7 100644
@@ -64,10 +64,10 @@ led-0 {
 
Quoted 11 lines

arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts led-0 { · line 68

Quoted 7 lines
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts +1 -3
         fan: pwm-fan {
                 compatible = "pwm-fan";
-               cooling-levels = <0 120 150 180 210 240 255>;
-               fan-supply = <&vcc5v0_sys>;
-               pwms = <&pwm1 0 50000 0>;
                 #cooling-cells = <2>;
+               cooling-levels = <0 64 128 192 255>;

Could you please share your testing setup for this part? In my experience using Radxa 4010 fan, it didn't spin up reliably below 120, so the value of 64 looks not helpful here.

I'm sorry, I have only 2513, it doesn't work on 5B with/without this patch. so I couldn't test this part. (btw I'll get 4012 soon)

then, thank you for your test report, I'll keep old value.

Best regards,

--
FUKAUMI Naoki
Radxa Computer (Shenzhen) Co., Ltd.

Quoted 3 lines

Best regards,
Alexey

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip

#8 lore raw

PATCH 6/6 arm64: dts: rockchip: fix rtc node for Radxa ROCK 5B

In reply to FUKAUMI Naoki

fix pin names to match with schematic.

---
 arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts +5 -5
index 6a02febaefb7..fbe231973b24 100644
@@ -300,11 +300,11 @@ hym8563: rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 		#clock-cells = <0>;
-		clock-output-names = "hym8563";
-		pinctrl-names = "default";
-		pinctrl-0 = <&hym8563_int>;
+		clock-output-names = "32kout_wifi";
 		interrupt-parent = <&gpio0>;
 		interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtc_int_l>;
 		wakeup-source;
 	};
 };
@@ -407,8 +407,8 @@ &pcie3x4 {
 };
 
 &pinctrl {
-	hym8563 {
-		hym8563_int: hym8563-int {
+	rtc {
+		rtc_int_l: rtc-int-l {
 			rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
Signature · 7 lines
2.43.0


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip