Skip to contentSkip to conversation

spi: spi-kspi2: Add KEBA SPI controller support

PATCH In review Gerhard Engleder 2 participants 2 messages Dec 2, 2024 – Dec 4, 2024 SPI

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 spi: spi-kspi2: Add KEBA SPI controller support

From: Gerhard Engleder <[email protected]>

The KEBA SPI controller is found in the system FPGA of KEBA PLC devices. It is used to connect the SPI flash chip of the FPGA and some SPI devices.

It is a simple SPI controller with configurable speed. The hardware supports only single byte transfers. There are no FIFOs or interrupts.

---
 drivers/spi/Kconfig     |  12 ++
 drivers/spi/Makefile    |   1 +
 drivers/spi/spi-kspi2.c | 431 ++++++++++++++++++++++++++++++++++++++++
 3 files changed, 444 insertions(+)
 create mode 100644 drivers/spi/spi-kspi2.c
drivers/spi/Kconfig +12 -0
index f51f9466e518..ea8a31032927 100644
@@ -542,6 +542,18 @@ config SPI_JCORE
 	  This enables support for the SPI master controller in the J-Core
 	  synthesizable, open source SoC.
 
+config SPI_KSPI2
+	tristate "Support for KEBA SPI master type 2 hardware"
+	depends on HAS_IOMEM
+	depends on KEBA_CP500 || COMPILE_TEST
+	select AUXILIARY_BUS
+	help
+	  This driver supports KEBA SPI master type 2 FPGA implementation,
+	  as found on CP500 devices for example.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called spi-kspi2.
+
 config SPI_LM70_LLP
 	tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
 	depends on PARPORT
drivers/spi/Makefile +1 -0
index aea5e54de195..9db7554c1864 100644
@@ -74,6 +74,7 @@ obj-$(CONFIG_SPI_INTEL_PCI)		+= spi-intel-pci.o
 obj-$(CONFIG_SPI_INTEL_PLATFORM)	+= spi-intel-platform.o
 obj-$(CONFIG_SPI_LANTIQ_SSC)		+= spi-lantiq-ssc.o
 obj-$(CONFIG_SPI_JCORE)			+= spi-jcore.o
+obj-$(CONFIG_SPI_KSPI2)			+= spi-kspi2.o
 obj-$(CONFIG_SPI_LJCA)			+= spi-ljca.o
 obj-$(CONFIG_SPI_LM70_LLP)		+= spi-lm70llp.o
 obj-$(CONFIG_SPI_LOONGSON_CORE)		+= spi-loongson-core.o
drivers/spi/spi-kspi2.c new file +431 -0

431 lines not on this page · raw message

Signature · 1 line
2.39.2
maintainer
#1 lore raw
Quoted 8 lines · Gerhard Engleder

The KEBA SPI controller is found in the system FPGA of KEBA PLC devices. It is used to connect the SPI flash chip of the FPGA and some SPI devices.

It is a simple SPI controller with configurable speed. The hardware supports only single byte transfers. There are no FIFOs or interrupts.

[...]

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next

Thanks!

[1/1] spi: spi-kspi2: Add KEBA SPI controller support

      commit: 1a90aae3b25b72e639da6062e0dc5efb9cff58f1

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark