Skip to contentSkip to conversation

Add SDM670 camera subsystem

PATCH Superseded Richard Acayan 4 participants 15 messages Dec 16, 2024 – Dec 17, 2024

Subsystems (8)

v8 of 10 Superseded Latest is v10 →

lore
Share & tools
lore
#0 lore raw

v8 cover Add SDM670 camera subsystem

This adds support for the camera subsystem on the Snapdragon 670.

Changes since v7 ([email protected]):
- move regulators to CSIPHY blocks (3/5)
- move clocks before interrupts (2/5, 5/5)
- sort clocks alphanumerically (2/5, 5/5)
- rename example node to generic node name (2/5)

Changes since v6 ([email protected]):
- set unit address in node name to first address in regs (2/5, 5/5)

Changes since v5 ([email protected]):
- sort reg and reg-names alphabetically (2/5, 5/5)
- drop CCI I2C patches since they are applied (formerly 2/7, 3/7)

Changes since v4 ([email protected]):
- change camss interrupts to rising edge in dts (7/7)
- change IRQs to rising edge in camss dt-bindings example (4/7)
- move gcc and ahb clocks in camss dt-bindings example (4/7)
- add reviewed-by for camcc dt-bindings patch (1/7)

Changes since v3 ([email protected]):
- add specific sdm670 compatible for camcc to dt schema and dts (1/7, 6/7)
- pick up patch from Bryan for CCI driver (3/7)
- stop assigning CCI frequency in dts (7/7)
- add maxItems for sdm670 cci clocks (2/7)
- remove empty line at top of camss dt schema (4/7)
- move regs and reg-names up in camss dt schema (4/7)
- move gcc and ahb clocks up in dts and dt schema (4/7, 7/7)
- add reviewed-by from Vladimir for CCI dt-bindings patch (2/7)
- add reviewed-by from Bryan for dts patch (7/7)
- add reviewed-by from Krzysztof for camss dt-bindings patch (4/7)
- add rewiew tags for camss driver patch (5/7)

Changes since v2 ([email protected]):
- drop unnecessary assigned AXI clock frequency (5/5)
- drop src clocks from cci (5/5)
- add unit name, remove mmio properties from port in example dts (2/5)
- correct the reg-names order (2/5)
- add parent_dev_ops to csid (3/5)
- remove CSID clocks from VFE (3/5)
- remove AXI clock from CSIPHY (3/5)
- change subsystem part of the commit message summary (3/5)
- add reviewed-by (4/5)

Changes since v1 ([email protected]):
- define dedicated resource structs/arrays for sdm670 (3/5)
- separate camcc device tree node into its own patch (4/5)
- specify correct dual license (2/5)
- add include directives in dt-bindings camss example (2/5)
- remove src clocks from dt-bindings (2/5)
- remove src clocks from dtsi (5/5)
- add power-domain-names to camss (5/5)
- specify power domain names (3/5)
- restrict cci-i2c clocks (1/5)
- populate a commit message with hw info (2/5)
- reword commit message (3/5)

Richard Acayan (5):
dt-bindings: clock: qcom,sdm845-camcc: add sdm670 compatible
dt-bindings: media: camss: Add qcom,sdm670-camss
media: qcom: camss: add support for SDM670 camss
arm64: dts: qcom: sdm670: add camcc
arm64: dts: qcom: sdm670: add camss and cci

 .../bindings/clock/qcom,sdm845-camcc.yaml     |   6 +-
 .../bindings/media/qcom,sdm670-camss.yaml     | 318 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/sdm670.dtsi          | 195 +++++++++++
 drivers/media/platform/qcom/camss/camss.c     | 191 +++++++++++
 4 files changed, 709 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml
Signature · 1 line
2.47.1
#1 lore raw

PATCH v8 1/5 dt-bindings: clock: qcom,sdm845-camcc: add sdm670 compatible

The camera clocks on SDM670 and SDM845 have no significant differences that would require a change in the clock controller driver. The only difference is the clock frequency at each level of the power domains, which is not specified in the clock driver. There should still be a compatible specific to the SoC, so add the compatible for SDM670 with the SDM845 compatible as fallback.

---
 .../devicetree/bindings/clock/qcom,sdm845-camcc.yaml        | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/clock/qcom,sdm845-camcc.yaml +5 -1
index 810b852ae371..fa95c3a1ba3a 100644
@@ -20,7 +20,11 @@ allOf:
 
 properties:
   compatible:
-    const: qcom,sdm845-camcc
+    oneOf:
+      - items:
+          - const: qcom,sdm670-camcc
+          - const: qcom,sdm845-camcc
+      - const: qcom,sdm845-camcc
 
   clocks:
     items:
Signature · 1 line
2.47.1
#2 lore raw

PATCH v8 2/5 dt-bindings: media: camss: Add qcom,sdm670-camss

In reply to Richard Acayan

As found in the Pixel 3a, the Snapdragon 670 has a camera subsystem with 3 CSIDs and 3 VFEs (including 1 VFE lite). Add this camera subsystem to the bindings.

Adapted from SC8280XP camera subsystem.

---
 .../bindings/media/qcom,sdm670-camss.yaml     | 318 ++++++++++++++++++
 1 file changed, 318 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml
Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml new file +318 -0
new file mode 100644
index 000000000000..f8701a8d27fe
@@ -0,0 +1,318 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/qcom,sdm670-camss.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SDM670 Camera Subsystem (CAMSS)
+
+maintainers:
+  - Richard Acayan <[email protected]>
+
+description:
+  The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms.
+
+properties:
+  compatible:
+    const: qcom,sdm670-camss
+
+  reg:
+    maxItems: 9
+
+  reg-names:
+    items:
+      - const: csid0
+      - const: csid1
+      - const: csid2
+      - const: csiphy0
+      - const: csiphy1
+      - const: csiphy2
+      - const: vfe0
+      - const: vfe1
+      - const: vfe_lite
+
+  interrupts:
+    maxItems: 9
+
+  interrupt-names:
+    items:
+      - const: csid0
+      - const: csid1
+      - const: csid2
+      - const: csiphy0
+      - const: csiphy1
+      - const: csiphy2
+      - const: vfe0
+      - const: vfe1
+      - const: vfe_lite
+
+  clocks:
+    maxItems: 22
+
+  clock-names:
+    items:
+      - const: camnoc_axi
+      - const: cpas_ahb
+      - const: csi0
+      - const: csi1
+      - const: csi2
+      - const: csiphy0
+      - const: csiphy0_timer
+      - const: csiphy1
+      - const: csiphy1_timer
+      - const: csiphy2
+      - const: csiphy2_timer
+      - const: gcc_camera_ahb
+      - const: gcc_camera_axi
+      - const: soc_ahb
+      - const: vfe0
+      - const: vfe0_axi
+      - const: vfe0_cphy_rx
+      - const: vfe1
+      - const: vfe1_axi
+      - const: vfe1_cphy_rx
+      - const: vfe_lite
+      - const: vfe_lite_cphy_rx
+
+  iommus:
+    maxItems: 4
+
+  power-domains:
+    items:
+      - description: IFE0 GDSC - Image Front End, Global Distributed Switch Controller.
+      - description: IFE1 GDSC - Image Front End, Global Distributed Switch Controller.
+      - description: Titan Top GDSC - Titan ISP Block, Global Distributed Switch Controller.
+
+  power-domain-names:
+    items:
+      - const: ife0
+      - const: ife1
+      - const: top
+
+  vdda-phy-supply:
+    description:
+      Phandle to a regulator supply to PHY core block.
+
+  vdda-pll-supply:
+    description:
+      Phandle to 1.8V regulator supply to PHY refclk pll block.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    description:
+      CSI input ports.
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data from CSIPHY0.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+      port@1:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data from CSIPHY1.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+      port@2:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data from CSIPHY2.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - interrupt-names
+  - clocks
+  - clock-names
+  - iommus
+  - power-domains
+  - power-domain-names
+  - vdda-phy-supply
+  - vdda-pll-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,camcc-sdm845.h>
+    #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        camera-controller@acb3000 {
+            compatible = "qcom,sdm670-camss";
+
+            reg = <0 0x0acb3000 0 0x1000>,
+                  <0 0x0acba000 0 0x1000>,
+                  <0 0x0acc8000 0 0x1000>,
+                  <0 0x0ac65000 0 0x1000>,
+                  <0 0x0ac66000 0 0x1000>,
+                  <0 0x0ac67000 0 0x1000>,
+                  <0 0x0acaf000 0 0x4000>,
+                  <0 0x0acb6000 0 0x4000>,
+                  <0 0x0acc4000 0 0x4000>;
+            reg-names = "csid0",
+                        "csid1",
+                        "csid2",
+                        "csiphy0",
+                        "csiphy1",
+                        "csiphy2",
+                        "vfe0",
+                        "vfe1",
+                        "vfe_lite";
+
+            interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>;
+            interrupt-names = "csid0",
+                              "csid1",
+                              "csid2",
+                              "csiphy0",
+                              "csiphy1",
+                              "csiphy2",
+                              "vfe0",
+                              "vfe1",
+                              "vfe_lite";
+
+            clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+                     <&camcc CAM_CC_CPAS_AHB_CLK>,
+                     <&camcc CAM_CC_IFE_0_CSID_CLK>,
+                     <&camcc CAM_CC_IFE_1_CSID_CLK>,
+                     <&camcc CAM_CC_IFE_LITE_CSID_CLK>,
+                     <&camcc CAM_CC_CSIPHY0_CLK>,
+                     <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
+                     <&camcc CAM_CC_CSIPHY1_CLK>,
+                     <&camcc CAM_CC_CSI1PHYTIMER_CLK>,
+                     <&camcc CAM_CC_CSIPHY2_CLK>,
+                     <&camcc CAM_CC_CSI2PHYTIMER_CLK>,
+                     <&gcc GCC_CAMERA_AHB_CLK>,
+                     <&gcc GCC_CAMERA_AXI_CLK>,
+                     <&camcc CAM_CC_SOC_AHB_CLK>,
+                     <&camcc CAM_CC_IFE_0_CLK>,
+                     <&camcc CAM_CC_IFE_0_AXI_CLK>,
+                     <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>,
+                     <&camcc CAM_CC_IFE_1_CLK>,
+                     <&camcc CAM_CC_IFE_1_AXI_CLK>,
+                     <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>,
+                     <&camcc CAM_CC_IFE_LITE_CLK>,
+                     <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>;
+            clock-names = "camnoc_axi",
+                          "cpas_ahb",
+                          "csi0",
+                          "csi1",
+                          "csi2",
+                          "csiphy0",
+                          "csiphy0_timer",
+                          "csiphy1",
+                          "csiphy1_timer",
+                          "csiphy2",
+                          "csiphy2_timer",
+                          "gcc_camera_ahb",
+                          "gcc_camera_axi",
+                          "soc_ahb",
+                          "vfe0",
+                          "vfe0_axi",
+                          "vfe0_cphy_rx",
+                          "vfe1",
+                          "vfe1_axi",
+                          "vfe1_cphy_rx",
+                          "vfe_lite",
+                          "vfe_lite_cphy_rx";
+
+            iommus = <&apps_smmu 0x808 0x0>,
+                     <&apps_smmu 0x810 0x8>,
+                     <&apps_smmu 0xc08 0x0>,
+                     <&apps_smmu 0xc10 0x8>;
+
+            power-domains = <&camcc IFE_0_GDSC>,
+                            <&camcc IFE_1_GDSC>,
+                            <&camcc TITAN_TOP_GDSC>;
+            power-domain-names = "ife0",
+                                 "ife1",
+                                 "top";
+
+            vdda-phy-supply = <&vreg_l1a_1p225>;
+            vdda-pll-supply = <&vreg_l8a_1p8>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+
+                    csiphy_ep0: endpoint {
+                        clock-lanes = <7>;
+                        data-lanes = <0 1 2 3>;
+                        remote-endpoint = <&front_sensor_ep>;
+                    };
+                };
+            };
+        };
+    };
Signature · 1 line
2.47.1
maintainer Reviewed-by on v8 2/5
#3 lore raw

Re: [PATCH v8 2/5] dt-bindings: media: camss: Add qcom,sdm670-camss

Quoted 210 lines · Richard Acayan

As found in the Pixel 3a, the Snapdragon 670 has a camera subsystem with 3 CSIDs and 3 VFEs (including 1 VFE lite). Add this camera subsystem to the bindings.

Adapted from SC8280XP camera subsystem.

---
  .../bindings/media/qcom,sdm670-camss.yaml     | 318 ++++++++++++++++++
  1 file changed, 318 insertions(+)

create mode 100644 Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml

Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml new file +192 -0
new file mode 100644
index 000000000000..f8701a8d27fe
@@ -0,0 +1,318 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/qcom,sdm670-camss.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SDM670 Camera Subsystem (CAMSS)
+
+maintainers:
+  - Richard Acayan <[email protected]>
+
+description:
+  The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms.
+
+properties:
+  compatible:
+    const: qcom,sdm670-camss
+
+  reg:
+    maxItems: 9
+
+  reg-names:
+    items:
+      - const: csid0
+      - const: csid1
+      - const: csid2
+      - const: csiphy0
+      - const: csiphy1
+      - const: csiphy2
+      - const: vfe0
+      - const: vfe1
+      - const: vfe_lite
+
+  interrupts:
+    maxItems: 9
+
+  interrupt-names:
+    items:
+      - const: csid0
+      - const: csid1
+      - const: csid2
+      - const: csiphy0
+      - const: csiphy1
+      - const: csiphy2
+      - const: vfe0
+      - const: vfe1
+      - const: vfe_lite
+
+  clocks:
+    maxItems: 22
+
+  clock-names:
+    items:
+      - const: camnoc_axi
+      - const: cpas_ahb
+      - const: csi0
+      - const: csi1
+      - const: csi2
+      - const: csiphy0
+      - const: csiphy0_timer
+      - const: csiphy1
+      - const: csiphy1_timer
+      - const: csiphy2
+      - const: csiphy2_timer
+      - const: gcc_camera_ahb
+      - const: gcc_camera_axi
+      - const: soc_ahb
+      - const: vfe0
+      - const: vfe0_axi
+      - const: vfe0_cphy_rx
+      - const: vfe1
+      - const: vfe1_axi
+      - const: vfe1_cphy_rx
+      - const: vfe_lite
+      - const: vfe_lite_cphy_rx
+
+  iommus:
+    maxItems: 4
+
+  power-domains:
+    items:
+      - description: IFE0 GDSC - Image Front End, Global Distributed Switch Controller.
+      - description: IFE1 GDSC - Image Front End, Global Distributed Switch Controller.
+      - description: Titan Top GDSC - Titan ISP Block, Global Distributed Switch Controller.
+
+  power-domain-names:
+    items:
+      - const: ife0
+      - const: ife1
+      - const: top
+
+  vdda-phy-supply:
+    description:
+      Phandle to a regulator supply to PHY core block.
+
+  vdda-pll-supply:
+    description:
+      Phandle to 1.8V regulator supply to PHY refclk pll block.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    description:
+      CSI input ports.
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data from CSIPHY0.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+      port@1:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data from CSIPHY1.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+      port@2:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data from CSIPHY2.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - interrupt-names
+  - clocks
+  - clock-names
+  - iommus
+  - power-domains
+  - power-domain-names
+  - vdda-phy-supply
+  - vdda-pll-supply
+
+additionalProperties: false
+
+examples:

Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml line 202

Quoted 10 lines
Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml new file +10 -0
+  - |
+    #include <dt-bindings/clock/qcom,camcc-sdm845.h>
+    #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        camera-controller@acb3000 {

isp@

Quoted 107 lines
Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml new file +106 -0
+            compatible = "qcom,sdm670-camss";
+
+            reg = <0 0x0acb3000 0 0x1000>,
+                  <0 0x0acba000 0 0x1000>,
+                  <0 0x0acc8000 0 0x1000>,
+                  <0 0x0ac65000 0 0x1000>,
+                  <0 0x0ac66000 0 0x1000>,
+                  <0 0x0ac67000 0 0x1000>,
+                  <0 0x0acaf000 0 0x4000>,
+                  <0 0x0acb6000 0 0x4000>,
+                  <0 0x0acc4000 0 0x4000>;
+            reg-names = "csid0",
+                        "csid1",
+                        "csid2",
+                        "csiphy0",
+                        "csiphy1",
+                        "csiphy2",
+                        "vfe0",
+                        "vfe1",
+                        "vfe_lite";
+
+            interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>;
+            interrupt-names = "csid0",
+                              "csid1",
+                              "csid2",
+                              "csiphy0",
+                              "csiphy1",
+                              "csiphy2",
+                              "vfe0",
+                              "vfe1",
+                              "vfe_lite";
 
+
+            clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+                     <&camcc CAM_CC_CPAS_AHB_CLK>,
+                     <&camcc CAM_CC_IFE_0_CSID_CLK>,
+                     <&camcc CAM_CC_IFE_1_CSID_CLK>,
+                     <&camcc CAM_CC_IFE_LITE_CSID_CLK>,
+                     <&camcc CAM_CC_CSIPHY0_CLK>,
+                     <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
+                     <&camcc CAM_CC_CSIPHY1_CLK>,
+                     <&camcc CAM_CC_CSI1PHYTIMER_CLK>,
+                     <&camcc CAM_CC_CSIPHY2_CLK>,
+                     <&camcc CAM_CC_CSI2PHYTIMER_CLK>,
+                     <&gcc GCC_CAMERA_AHB_CLK>,
+                     <&gcc GCC_CAMERA_AXI_CLK>,
+                     <&camcc CAM_CC_SOC_AHB_CLK>,
+                     <&camcc CAM_CC_IFE_0_CLK>,
+                     <&camcc CAM_CC_IFE_0_AXI_CLK>,
+                     <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>,
+                     <&camcc CAM_CC_IFE_1_CLK>,
+                     <&camcc CAM_CC_IFE_1_AXI_CLK>,
+                     <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>,
+                     <&camcc CAM_CC_IFE_LITE_CLK>,
+                     <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>;
+            clock-names = "camnoc_axi",
+                          "cpas_ahb",
+                          "csi0",
+                          "csi1",
+                          "csi2",
+                          "csiphy0",
+                          "csiphy0_timer",
+                          "csiphy1",
+                          "csiphy1_timer",
+                          "csiphy2",
+                          "csiphy2_timer",
+                          "gcc_camera_ahb",
+                          "gcc_camera_axi",
+                          "soc_ahb",
+                          "vfe0",
+                          "vfe0_axi",
+                          "vfe0_cphy_rx",
+                          "vfe1",
+                          "vfe1_axi",
+                          "vfe1_cphy_rx",
+                          "vfe_lite",
+                          "vfe_lite_cphy_rx";
+
+            iommus = <&apps_smmu 0x808 0x0>,
+                     <&apps_smmu 0x810 0x8>,
+                     <&apps_smmu 0xc08 0x0>,
+                     <&apps_smmu 0xc10 0x8>;
+
+            power-domains = <&camcc IFE_0_GDSC>,
+                            <&camcc IFE_1_GDSC>,
+                            <&camcc TITAN_TOP_GDSC>;
+            power-domain-names = "ife0",
+                                 "ife1",
+                                 "top";
+
+            vdda-phy-supply = <&vreg_l1a_1p225>;
+            vdda-pll-supply = <&vreg_l8a_1p8>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;

Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml line 318

Quoted 10 lines
Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml new file +10 -0
+
+                    csiphy_ep0: endpoint {
+                        clock-lanes = <7>;
+                        data-lanes = <0 1 2 3>;
+                        remote-endpoint = <&front_sensor_ep>;
+                    };
+                };
+            };
+        };
+    };

Otherwise LGTM

Reviewed-by on v8 2/5
#4 lore raw

Re: [PATCH v8 2/5] dt-bindings: media: camss: Add qcom,sdm670-camss

In reply to Richard Acayan
Quoted 11 lines · Richard Acayan

As found in the Pixel 3a, the Snapdragon 670 has a camera subsystem with 3 CSIDs and 3 VFEs (including 1 VFE lite). Add this camera subsystem to the bindings.

Adapted from SC8280XP camera subsystem.

---
 .../bindings/media/qcom,sdm670-camss.yaml     | 318 ++++++++++++++++++
 1 file changed, 318 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml

Best regards,
Krzysztof

#5 lore raw

PATCH v8 3/5 media: qcom: camss: add support for SDM670 camss

In reply to Richard Acayan

The camera subsystem for the SDM670 the same as on SDM845 except with 3 CSIPHY ports instead of 4. Add support for the SDM670 camera subsystem.

---
 .../bindings/media/qcom,sdm670-camss.yaml     |  72 +++----
 drivers/media/platform/qcom/camss/camss.c     | 191 ++++++++++++++++++
 2 files changed, 227 insertions(+), 36 deletions(-)
Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml +36 -36
index f8701a8d27fe..892412fb68a9 100644
@@ -31,21 +31,6 @@ properties:
       - const: vfe1
       - const: vfe_lite
 
-  interrupts:
-    maxItems: 9
-
-  interrupt-names:
-    items:
-      - const: csid0
-      - const: csid1
-      - const: csid2
-      - const: csiphy0
-      - const: csiphy1
-      - const: csiphy2
-      - const: vfe0
-      - const: vfe1
-      - const: vfe_lite
-
   clocks:
     maxItems: 22
 
@@ -74,6 +59,21 @@ properties:
       - const: vfe_lite
       - const: vfe_lite_cphy_rx
 
+  interrupts:
+    maxItems: 9
+
+  interrupt-names:
+    items:
+      - const: csid0
+      - const: csid1
+      - const: csid2
+      - const: csiphy0
+      - const: csiphy1
+      - const: csiphy2
+      - const: vfe0
+      - const: vfe1
+      - const: vfe_lite
+
   iommus:
     maxItems: 4
 
@@ -177,10 +177,10 @@ required:
   - compatible
   - reg
   - reg-names
-  - interrupts
-  - interrupt-names
   - clocks
   - clock-names
+  - interrupts
+  - interrupt-names
   - iommus
   - power-domains
   - power-domain-names
@@ -221,25 +221,6 @@ examples:
                         "vfe1",
                         "vfe_lite";
 
-            interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
-                         <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>,
-                         <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>,
-                         <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
-                         <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
-                         <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
-                         <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>,
-                         <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>,
-                         <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>;
-            interrupt-names = "csid0",
-                              "csid1",
-                              "csid2",
-                              "csiphy0",
-                              "csiphy1",
-                              "csiphy2",
-                              "vfe0",
-                              "vfe1",
-                              "vfe_lite";
-
             clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
                      <&camcc CAM_CC_CPAS_AHB_CLK>,
                      <&camcc CAM_CC_IFE_0_CSID_CLK>,
@@ -285,6 +266,25 @@ examples:
                           "vfe_lite",
                           "vfe_lite_cphy_rx";
 
+            interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>;
+            interrupt-names = "csid0",
+                              "csid1",
+                              "csid2",
+                              "csiphy0",
+                              "csiphy1",
+                              "csiphy2",
+                              "vfe0",
+                              "vfe1",
+                              "vfe_lite";
+
             iommus = <&apps_smmu 0x808 0x0>,
                      <&apps_smmu 0x810 0x8>,
                      <&apps_smmu 0xc08 0x0>,
drivers/media/platform/qcom/camss/camss.c +191 -0

209 lines not on this page · raw message

Signature · 1 line
2.47.1
maintainer
#6 lore raw

Re: [PATCH v8 3/5] media: qcom: camss: add support for SDM670 camss

Quoted 9 lines · Richard Acayan
  .../bindings/media/qcom,sdm670-camss.yaml     |  72 +++----
  drivers/media/platform/qcom/camss/camss.c     | 191 ++++++++++++++++++
  2 files changed, 227 insertions(+), 36 deletions(-)
Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml +0 -0
index f8701a8d27fe..892412fb68a9 100644

Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml properties: · line 35

Quoted 5 lines
Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml +0 -2
@@ -31,21 +31,6 @@ properties:
        - const: vfe1
        - const: vfe_lite
 
-  interrupts:
-    maxItems: 9

I think you've had an error squashing some patches.

---
bod

#7 lore raw

Re: [PATCH v8 3/5] media: qcom: camss: add support for SDM670 camss

Quoted 5 lines · Bryan O'Donoghue
Quoted 4 lines · Richard Acayan
  .../bindings/media/qcom,sdm670-camss.yaml     |  72 +++----
  drivers/media/platform/qcom/camss/camss.c     | 191 ++++++++++++++++++
  2 files changed, 227 insertions(+), 36 deletions(-)
Quoted 11 lines

Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml properties: · line 34

Quoted 9 lines
Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml +0 -2
index f8701a8d27fe..892412fb68a9 100644
@@ -31,21 +31,6 @@ properties:
        - const: vfe1
        - const: vfe_lite
-  interrupts:
-    maxItems: 9

I think you've had an error squashing some patches.

Yeah, copy-paste error... best to revert the change (and change back DTS).

#8 lore raw

Re: [PATCH v8 3/5] media: qcom: camss: add support for SDM670 camss

In reply to Richard Acayan
Quoted 11 lines · Richard Acayan

The camera subsystem for the SDM670 the same as on SDM845 except with 3 CSIPHY ports instead of 4. Add support for the SDM670 camera subsystem.

---
 .../bindings/media/qcom,sdm670-camss.yaml     |  72 +++----
 drivers/media/platform/qcom/camss/camss.c     | 191 ++++++++++++++++++

You cannot combine such changes. Bindings are always separate.

Please run scripts/checkpatch.pl and fix reported warnings. Then please run 'scripts/checkpatch.pl --strict' and (probably) fix more warnings. Some warnings can be ignored, especially from --strict run, but the code here looks like it needs a fix. Feel free to get in touch if the warning is not clear.

Please drop the review/ack tags and request re-review for this patch.

Best regards,
Krzysztof

#9 lore raw

PATCH v8 4/5 arm64: dts: qcom: sdm670: add camcc

In reply to Richard Acayan

The camera clock controller on SDM670 controls the clocks that drive the camera subsystem. The clocks are the same as on SDM845. Add the camera clock controller for SDM670.

---
 arch/arm64/boot/dts/qcom/sdm670.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)
arch/arm64/boot/dts/qcom/sdm670.dtsi +10 -0
index c93dd06c0b7d..328096b91126 100644
@@ -1400,6 +1400,16 @@ spmi_bus: spmi@c440000 {
 			#interrupt-cells = <4>;
 		};
 
+		camcc: clock-controller@ad00000 {
+			compatible = "qcom,sdm670-camcc", "qcom,sdm845-camcc";
+			reg = <0 0x0ad00000 0 0x10000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "bi_tcxo";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
 		mdss: display-subsystem@ae00000 {
 			compatible = "qcom,sdm670-mdss";
 			reg = <0 0x0ae00000 0 0x1000>;
Signature · 1 line
2.47.1
#10 lore raw

PATCH v8 5/5 arm64: dts: qcom: sdm670: add camss and cci

In reply to Richard Acayan

Add the camera subsystem and CCI used to interface with cameras on the Snapdragon 670.

---
 arch/arm64/boot/dts/qcom/sdm670.dtsi | 185 +++++++++++++++++++++++++++
 1 file changed, 185 insertions(+)
arch/arm64/boot/dts/qcom/sdm670.dtsi +185 -0
index 328096b91126..d4e1251ada04 100644
@@ -6,6 +6,7 @@
  * Copyright (c) 2022, Richard Acayan. All rights reserved.
  */
 
+#include <dt-bindings/clock/qcom,camcc-sdm845.h>
 #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
 #include <dt-bindings/clock/qcom,gcc-sdm845.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
@@ -1168,6 +1169,34 @@ tlmm: pinctrl@3400000 {
 			gpio-ranges = <&tlmm 0 0 151>;
 			wakeup-parent = <&pdc>;
 
+			cci0_default: cci0-default-state {
+				pins = "gpio17", "gpio18";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			cci0_sleep: cci0-sleep-state {
+				pins = "gpio17", "gpio18";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			cci1_default: cci1-default-state {
+				pins = "gpio19", "gpio20";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			cci1_sleep: cci1-sleep-state {
+				pins = "gpio19", "gpio20";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
 			qup_i2c0_default: qup-i2c0-default-state {
 				pins = "gpio0", "gpio1";
 				function = "qup0";
@@ -1400,6 +1429,162 @@ spmi_bus: spmi@c440000 {
 			#interrupt-cells = <4>;
 		};
 
+		cci: cci@ac4a000 {
+			compatible = "qcom,sdm670-cci", "qcom,msm8996-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg = <0 0x0ac4a000 0 0x4000>;
+			interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
+			power-domains = <&camcc TITAN_TOP_GDSC>;
+
+			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_SOC_AHB_CLK>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_CCI_CLK>;
+			clock-names = "camnoc_axi",
+				      "soc_ahb",
+				      "cpas_ahb",
+				      "cci";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&cci0_default &cci1_default>;
+			pinctrl-1 = <&cci0_sleep &cci1_sleep>;
+
+			status = "disabled";
+
+			cci_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <1000000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			cci_i2c1: i2c-bus@1 {
+				reg = <1>;
+				clock-frequency = <1000000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		camss: camera-controller@acb3000 {
+			compatible = "qcom,sdm670-camss";
+			reg = <0 0x0acb3000 0 0x1000>,
+			      <0 0x0acba000 0 0x1000>,
+			      <0 0x0acc8000 0 0x1000>,
+			      <0 0x0ac65000 0 0x1000>,
+			      <0 0x0ac66000 0 0x1000>,
+			      <0 0x0ac67000 0 0x1000>,
+			      <0 0x0acaf000 0 0x4000>,
+			      <0 0x0acb6000 0 0x4000>,
+			      <0 0x0acc4000 0 0x4000>;
+			reg-names = "csid0",
+				    "csid1",
+				    "csid2",
+				    "csiphy0",
+				    "csiphy1",
+				    "csiphy2",
+				    "vfe0",
+				    "vfe1",
+				    "vfe_lite";
+
+			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_0_CSID_CLK>,
+				 <&camcc CAM_CC_IFE_1_CSID_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CSID_CLK>,
+				 <&camcc CAM_CC_CSIPHY0_CLK>,
+				 <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY1_CLK>,
+				 <&camcc CAM_CC_CSI1PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY2_CLK>,
+				 <&camcc CAM_CC_CSI2PHYTIMER_CLK>,
+				 <&gcc GCC_CAMERA_AHB_CLK>,
+				 <&gcc GCC_CAMERA_AXI_CLK>,
+				 <&camcc CAM_CC_SOC_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_0_CLK>,
+				 <&camcc CAM_CC_IFE_0_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_1_CLK>,
+				 <&camcc CAM_CC_IFE_1_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>;
+			clock-names = "camnoc_axi",
+				      "cpas_ahb",
+				      "csi0",
+				      "csi1",
+				      "csi2",
+				      "csiphy0",
+				      "csiphy0_timer",
+				      "csiphy1",
+				      "csiphy1_timer",
+				      "csiphy2",
+				      "csiphy2_timer",
+				      "gcc_camera_ahb",
+				      "gcc_camera_axi",
+				      "soc_ahb",
+				      "vfe0",
+				      "vfe0_axi",
+				      "vfe0_cphy_rx",
+				      "vfe1",
+				      "vfe1_axi",
+				      "vfe1_cphy_rx",
+				      "vfe_lite",
+				      "vfe_lite_cphy_rx";
+
+			interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "csid0",
+					  "csid1",
+					  "csid2",
+					  "csiphy0",
+					  "csiphy1",
+					  "csiphy2",
+					  "vfe0",
+					  "vfe1",
+					  "vfe_lite";
+
+			iommus = <&apps_smmu 0x808 0x0>,
+				 <&apps_smmu 0x810 0x8>,
+				 <&apps_smmu 0xc08 0x0>,
+				 <&apps_smmu 0xc10 0x8>;
+
+			power-domains = <&camcc IFE_0_GDSC>,
+					<&camcc IFE_1_GDSC>,
+					<&camcc TITAN_TOP_GDSC>;
+			power-domain-names = "ife0",
+					     "ife1",
+					     "top";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				camss_port0: port@0 {
+					reg = <0>;
+				};
+
+				camss_port1: port@1 {
+					reg = <1>;
+				};
+
+				camss_port2: port@2 {
+					reg = <2>;
+				};
+			};
+		};
+
 		camcc: clock-controller@ad00000 {
 			compatible = "qcom,sdm670-camcc", "qcom,sdm845-camcc";
 			reg = <0 0x0ad00000 0 0x10000>;
Signature · 1 line
2.47.1
reviewer Reviewed-by on v8 5/5
#11 lore raw

Re: [PATCH v8 5/5] arm64: dts: qcom: sdm670: add camss and cci

Hi Richard.

Quoted 90 lines · Richard Acayan

Add the camera subsystem and CCI used to interface with cameras on the Snapdragon 670.

---
  arch/arm64/boot/dts/qcom/sdm670.dtsi | 185 +++++++++++++++++++++++++++
  1 file changed, 185 insertions(+)
arch/arm64/boot/dts/qcom/sdm670.dtsi +59 -0
index 328096b91126..d4e1251ada04 100644
@@ -6,6 +6,7 @@
   * Copyright (c) 2022, Richard Acayan. All rights reserved.
   */
 
+#include <dt-bindings/clock/qcom,camcc-sdm845.h>
  #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
  #include <dt-bindings/clock/qcom,gcc-sdm845.h>
  #include <dt-bindings/clock/qcom,rpmh.h>
@@ -1168,6 +1169,34 @@ tlmm: pinctrl@3400000 {
  			gpio-ranges = <&tlmm 0 0 151>;
  			wakeup-parent = <&pdc>;
 
+			cci0_default: cci0-default-state {
+				pins = "gpio17", "gpio18";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			cci0_sleep: cci0-sleep-state {
+				pins = "gpio17", "gpio18";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			cci1_default: cci1-default-state {
+				pins = "gpio19", "gpio20";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			cci1_sleep: cci1-sleep-state {
+				pins = "gpio19", "gpio20";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
  			qup_i2c0_default: qup-i2c0-default-state {
  				pins = "gpio0", "gpio1";
  				function = "qup0";
@@ -1400,6 +1429,162 @@ spmi_bus: spmi@c440000 {
  			#interrupt-cells = <4>;
  		};
 
+		cci: cci@ac4a000 {
+			compatible = "qcom,sdm670-cci", "qcom,msm8996-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg = <0 0x0ac4a000 0 0x4000>;
+			interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
+			power-domains = <&camcc TITAN_TOP_GDSC>;
+
+			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_SOC_AHB_CLK>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_CCI_CLK>;
+			clock-names = "camnoc_axi",
+				      "soc_ahb",
+				      "cpas_ahb",
+				      "cci";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&cci0_default &cci1_default>;
+			pinctrl-1 = <&cci0_sleep &cci1_sleep>;
+
+			status = "disabled";
+
+			cci_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <1000000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};

arch/arm64/boot/dts/qcom/sdm670.dtsi spmi_bus: spmi@c440000 { · line 1471

Quoted 10 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +10 -0
+
+			cci_i2c1: i2c-bus@1 {
+				reg = <1>;
+				clock-frequency = <1000000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		camss: camera-controller@acb3000 {

Wasn't it agreed recently to have 'isp' as a generic device name for CAMSS IP?

Quoted 101 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +101 -0
+			compatible = "qcom,sdm670-camss";
+			reg = <0 0x0acb3000 0 0x1000>,
+			      <0 0x0acba000 0 0x1000>,
+			      <0 0x0acc8000 0 0x1000>,
+			      <0 0x0ac65000 0 0x1000>,
+			      <0 0x0ac66000 0 0x1000>,
+			      <0 0x0ac67000 0 0x1000>,
+			      <0 0x0acaf000 0 0x4000>,
+			      <0 0x0acb6000 0 0x4000>,
+			      <0 0x0acc4000 0 0x4000>;
+			reg-names = "csid0",
+				    "csid1",
+				    "csid2",
+				    "csiphy0",
+				    "csiphy1",
+				    "csiphy2",
+				    "vfe0",
+				    "vfe1",
+				    "vfe_lite";
+
+			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_0_CSID_CLK>,
+				 <&camcc CAM_CC_IFE_1_CSID_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CSID_CLK>,
+				 <&camcc CAM_CC_CSIPHY0_CLK>,
+				 <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY1_CLK>,
+				 <&camcc CAM_CC_CSI1PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY2_CLK>,
+				 <&camcc CAM_CC_CSI2PHYTIMER_CLK>,
+				 <&gcc GCC_CAMERA_AHB_CLK>,
+				 <&gcc GCC_CAMERA_AXI_CLK>,
+				 <&camcc CAM_CC_SOC_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_0_CLK>,
+				 <&camcc CAM_CC_IFE_0_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_1_CLK>,
+				 <&camcc CAM_CC_IFE_1_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>;
+			clock-names = "camnoc_axi",
+				      "cpas_ahb",
+				      "csi0",
+				      "csi1",
+				      "csi2",
+				      "csiphy0",
+				      "csiphy0_timer",
+				      "csiphy1",
+				      "csiphy1_timer",
+				      "csiphy2",
+				      "csiphy2_timer",
+				      "gcc_camera_ahb",
+				      "gcc_camera_axi",
+				      "soc_ahb",
+				      "vfe0",
+				      "vfe0_axi",
+				      "vfe0_cphy_rx",
+				      "vfe1",
+				      "vfe1_axi",
+				      "vfe1_cphy_rx",
+				      "vfe_lite",
+				      "vfe_lite_cphy_rx";
+
+			interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "csid0",
+					  "csid1",
+					  "csid2",
+					  "csiphy0",
+					  "csiphy1",
+					  "csiphy2",
+					  "vfe0",
+					  "vfe1",
+					  "vfe_lite";
+
+			iommus = <&apps_smmu 0x808 0x0>,
+				 <&apps_smmu 0x810 0x8>,
+				 <&apps_smmu 0xc08 0x0>,
+				 <&apps_smmu 0xc10 0x8>;
+
+			power-domains = <&camcc IFE_0_GDSC>,
+					<&camcc IFE_1_GDSC>,
+					<&camcc TITAN_TOP_GDSC>;
+			power-domain-names = "ife0",
+					     "ife1",
+					     "top";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;

arch/arm64/boot/dts/qcom/sdm670.dtsi spmi_bus: spmi@c440000 { · line 1582

Quoted 10 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +10 -0
+
+				camss_port0: port@0 {
+					reg = <0>;
+				};
+
+				camss_port1: port@1 {
+					reg = <1>;
+				};
+
+				camss_port2: port@2 {

Likely labels to ports are excessive here, please remove them.

arch/arm64/boot/dts/qcom/sdm670.dtsi spmi_bus: spmi@c440000 { · line 1590

Quoted 8 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +5 -0
+					reg = <2>;
+				};
+			};
+		};
+
  		camcc: clock-controller@ad00000 {
  			compatible = "qcom,sdm670-camcc", "qcom,sdm845-camcc";
  			reg = <0 0x0ad00000 0 0x10000>;

--
Best wishes,
Vladimir

#12 lore raw

Re: [PATCH v8 5/5] arm64: dts: qcom: sdm670: add camss and cci

Quoted 94 lines · Vladimir Zapolskiy

Hi Richard.

Quoted 91 lines · Richard Acayan

Add the camera subsystem and CCI used to interface with cameras on the Snapdragon 670.

---
  arch/arm64/boot/dts/qcom/sdm670.dtsi | 185 +++++++++++++++++++++++++++
  1 file changed, 185 insertions(+)
arch/arm64/boot/dts/qcom/sdm670.dtsi +63 -0
index 328096b91126..d4e1251ada04 100644
@@ -6,6 +6,7 @@
   * Copyright (c) 2022, Richard Acayan. All rights reserved.
   */
+#include <dt-bindings/clock/qcom,camcc-sdm845.h>
  #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
  #include <dt-bindings/clock/qcom,gcc-sdm845.h>
  #include <dt-bindings/clock/qcom,rpmh.h>
@@ -1168,6 +1169,34 @@ tlmm: pinctrl@3400000 {
  			gpio-ranges = <&tlmm 0 0 151>;
  			wakeup-parent = <&pdc>;
+			cci0_default: cci0-default-state {
+				pins = "gpio17", "gpio18";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			cci0_sleep: cci0-sleep-state {
+				pins = "gpio17", "gpio18";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			cci1_default: cci1-default-state {
+				pins = "gpio19", "gpio20";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			cci1_sleep: cci1-sleep-state {
+				pins = "gpio19", "gpio20";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
  			qup_i2c0_default: qup-i2c0-default-state {
  				pins = "gpio0", "gpio1";
  				function = "qup0";
@@ -1400,6 +1429,162 @@ spmi_bus: spmi@c440000 {
  			#interrupt-cells = <4>;
  		};
+		cci: cci@ac4a000 {
+			compatible = "qcom,sdm670-cci", "qcom,msm8996-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg = <0 0x0ac4a000 0 0x4000>;
+			interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
+			power-domains = <&camcc TITAN_TOP_GDSC>;
+
+			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_SOC_AHB_CLK>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_CCI_CLK>;
+			clock-names = "camnoc_axi",
+				      "soc_ahb",
+				      "cpas_ahb",
+				      "cci";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&cci0_default &cci1_default>;
+			pinctrl-1 = <&cci0_sleep &cci1_sleep>;
+
+			status = "disabled";
+
+			cci_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <1000000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			cci_i2c1: i2c-bus@1 {
+				reg = <1>;
+				clock-frequency = <1000000>;
Quoted 8 lines

arch/arm64/boot/dts/qcom/sdm670.dtsi spmi_bus: spmi@c440000 { · line 1471

Quoted 6 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +6 -0
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		camss: camera-controller@acb3000 {

Wasn't it agreed recently to have 'isp' as a generic device name for CAMSS IP?

Yeah, will change.

Quoted 106 lines
Quoted 106 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +105 -0
+			compatible = "qcom,sdm670-camss";
+			reg = <0 0x0acb3000 0 0x1000>,
+			      <0 0x0acba000 0 0x1000>,
+			      <0 0x0acc8000 0 0x1000>,
+			      <0 0x0ac65000 0 0x1000>,
+			      <0 0x0ac66000 0 0x1000>,
+			      <0 0x0ac67000 0 0x1000>,
+			      <0 0x0acaf000 0 0x4000>,
+			      <0 0x0acb6000 0 0x4000>,
+			      <0 0x0acc4000 0 0x4000>;
+			reg-names = "csid0",
+				    "csid1",
+				    "csid2",
+				    "csiphy0",
+				    "csiphy1",
+				    "csiphy2",
+				    "vfe0",
+				    "vfe1",
+				    "vfe_lite";
+
+			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_0_CSID_CLK>,
+				 <&camcc CAM_CC_IFE_1_CSID_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CSID_CLK>,
+				 <&camcc CAM_CC_CSIPHY0_CLK>,
+				 <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY1_CLK>,
+				 <&camcc CAM_CC_CSI1PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY2_CLK>,
+				 <&camcc CAM_CC_CSI2PHYTIMER_CLK>,
+				 <&gcc GCC_CAMERA_AHB_CLK>,
+				 <&gcc GCC_CAMERA_AXI_CLK>,
+				 <&camcc CAM_CC_SOC_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_0_CLK>,
+				 <&camcc CAM_CC_IFE_0_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_1_CLK>,
+				 <&camcc CAM_CC_IFE_1_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>;
+			clock-names = "camnoc_axi",
+				      "cpas_ahb",
+				      "csi0",
+				      "csi1",
+				      "csi2",
+				      "csiphy0",
+				      "csiphy0_timer",
+				      "csiphy1",
+				      "csiphy1_timer",
+				      "csiphy2",
+				      "csiphy2_timer",
+				      "gcc_camera_ahb",
+				      "gcc_camera_axi",
+				      "soc_ahb",
+				      "vfe0",
+				      "vfe0_axi",
+				      "vfe0_cphy_rx",
+				      "vfe1",
+				      "vfe1_axi",
+				      "vfe1_cphy_rx",
+				      "vfe_lite",
+				      "vfe_lite_cphy_rx";
+
+			interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "csid0",
+					  "csid1",
+					  "csid2",
+					  "csiphy0",
+					  "csiphy1",
+					  "csiphy2",
+					  "vfe0",
+					  "vfe1",
+					  "vfe_lite";
+
+			iommus = <&apps_smmu 0x808 0x0>,
+				 <&apps_smmu 0x810 0x8>,
+				 <&apps_smmu 0xc08 0x0>,
+				 <&apps_smmu 0xc10 0x8>;
+
+			power-domains = <&camcc IFE_0_GDSC>,
+					<&camcc IFE_1_GDSC>,
+					<&camcc TITAN_TOP_GDSC>;
+			power-domain-names = "ife0",
+					     "ife1",
+					     "top";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				camss_port0: port@0 {
+					reg = <0>;
+				};
Quoted 8 lines

arch/arm64/boot/dts/qcom/sdm670.dtsi spmi_bus: spmi@c440000 { · line 1582

Quoted 6 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +6 -0
+
+				camss_port1: port@1 {
+					reg = <1>;
+				};
+
+				camss_port2: port@2 {

Likely labels to ports are excessive here, please remove them.

How would you imagine connecting a camera to the ports, then? For MDSS, there's a label for the endpoint (mdss_dsi0_out) which the device DTS can then reference:

	&mdss_dsi0_out {
		remote-endpoint = <&panel_in>;
		data-lanes = <0 1 2 3>;
	};

For CAMSS, the port labels would be used like so:

	&camss_port1 {
		camss_endpoint1: endpoint {
			clock-lanes = <7>;
			data-lanes = <0 1 2 3>;
			remote-endpoint = <&cam_front_endpoint>;
		};
	};

Without the labels, the connection might look something like:

	&camss {
		status = "okay";

		// Modification of existing /soc/isp@acb3000/ports node
		ports {
			// Modification of existing /soc/isp@acb3000/ports/port@1 node
			port@1 {
				// New node
				camss_endpoint1: endpoint {
					clock-lanes = <7>;
					data-lanes = <0 1 2 3>;
					remote-endpoint = <&cam_front_endpoint>;
				};
			};
		};
	};

which I believe is not preferred.

#13 lore raw

Re: [PATCH v8 5/5] arm64: dts: qcom: sdm670: add camss and cci

Quoted 240 lines · Richard Acayan
Quoted 94 lines · Vladimir Zapolskiy

Hi Richard.

Quoted 91 lines · Richard Acayan

Add the camera subsystem and CCI used to interface with cameras on the Snapdragon 670.

---
   arch/arm64/boot/dts/qcom/sdm670.dtsi | 185 +++++++++++++++++++++++++++
   1 file changed, 185 insertions(+)
arch/arm64/boot/dts/qcom/sdm670.dtsi +63 -0
index 328096b91126..d4e1251ada04 100644
@@ -6,6 +6,7 @@
    * Copyright (c) 2022, Richard Acayan. All rights reserved.
    */
+#include <dt-bindings/clock/qcom,camcc-sdm845.h>
   #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
   #include <dt-bindings/clock/qcom,gcc-sdm845.h>
   #include <dt-bindings/clock/qcom,rpmh.h>
@@ -1168,6 +1169,34 @@ tlmm: pinctrl@3400000 {
   			gpio-ranges = <&tlmm 0 0 151>;
   			wakeup-parent = <&pdc>;
+			cci0_default: cci0-default-state {
+				pins = "gpio17", "gpio18";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			cci0_sleep: cci0-sleep-state {
+				pins = "gpio17", "gpio18";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			cci1_default: cci1-default-state {
+				pins = "gpio19", "gpio20";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			cci1_sleep: cci1-sleep-state {
+				pins = "gpio19", "gpio20";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
   			qup_i2c0_default: qup-i2c0-default-state {
   				pins = "gpio0", "gpio1";
   				function = "qup0";
@@ -1400,6 +1429,162 @@ spmi_bus: spmi@c440000 {
   			#interrupt-cells = <4>;
   		};
+		cci: cci@ac4a000 {
+			compatible = "qcom,sdm670-cci", "qcom,msm8996-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg = <0 0x0ac4a000 0 0x4000>;
+			interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
+			power-domains = <&camcc TITAN_TOP_GDSC>;
+
+			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_SOC_AHB_CLK>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_CCI_CLK>;
+			clock-names = "camnoc_axi",
+				      "soc_ahb",
+				      "cpas_ahb",
+				      "cci";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&cci0_default &cci1_default>;
+			pinctrl-1 = <&cci0_sleep &cci1_sleep>;
+
+			status = "disabled";
+
+			cci_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <1000000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			cci_i2c1: i2c-bus@1 {
+				reg = <1>;
+				clock-frequency = <1000000>;
Quoted 8 lines

arch/arm64/boot/dts/qcom/sdm670.dtsi spmi_bus: spmi@c440000 { · line 1471

Quoted 6 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +6 -0
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		camss: camera-controller@acb3000 {

Wasn't it agreed recently to have 'isp' as a generic device name for CAMSS IP?

Yeah, will change.

Quoted 106 lines
Quoted 106 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +105 -0
+			compatible = "qcom,sdm670-camss";
+			reg = <0 0x0acb3000 0 0x1000>,
+			      <0 0x0acba000 0 0x1000>,
+			      <0 0x0acc8000 0 0x1000>,
+			      <0 0x0ac65000 0 0x1000>,
+			      <0 0x0ac66000 0 0x1000>,
+			      <0 0x0ac67000 0 0x1000>,
+			      <0 0x0acaf000 0 0x4000>,
+			      <0 0x0acb6000 0 0x4000>,
+			      <0 0x0acc4000 0 0x4000>;
+			reg-names = "csid0",
+				    "csid1",
+				    "csid2",
+				    "csiphy0",
+				    "csiphy1",
+				    "csiphy2",
+				    "vfe0",
+				    "vfe1",
+				    "vfe_lite";
+
+			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_0_CSID_CLK>,
+				 <&camcc CAM_CC_IFE_1_CSID_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CSID_CLK>,
+				 <&camcc CAM_CC_CSIPHY0_CLK>,
+				 <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY1_CLK>,
+				 <&camcc CAM_CC_CSI1PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY2_CLK>,
+				 <&camcc CAM_CC_CSI2PHYTIMER_CLK>,
+				 <&gcc GCC_CAMERA_AHB_CLK>,
+				 <&gcc GCC_CAMERA_AXI_CLK>,
+				 <&camcc CAM_CC_SOC_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_0_CLK>,
+				 <&camcc CAM_CC_IFE_0_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_1_CLK>,
+				 <&camcc CAM_CC_IFE_1_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>;
+			clock-names = "camnoc_axi",
+				      "cpas_ahb",
+				      "csi0",
+				      "csi1",
+				      "csi2",
+				      "csiphy0",
+				      "csiphy0_timer",
+				      "csiphy1",
+				      "csiphy1_timer",
+				      "csiphy2",
+				      "csiphy2_timer",
+				      "gcc_camera_ahb",
+				      "gcc_camera_axi",
+				      "soc_ahb",
+				      "vfe0",
+				      "vfe0_axi",
+				      "vfe0_cphy_rx",
+				      "vfe1",
+				      "vfe1_axi",
+				      "vfe1_cphy_rx",
+				      "vfe_lite",
+				      "vfe_lite_cphy_rx";
+
+			interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "csid0",
+					  "csid1",
+					  "csid2",
+					  "csiphy0",
+					  "csiphy1",
+					  "csiphy2",
+					  "vfe0",
+					  "vfe1",
+					  "vfe_lite";
+
+			iommus = <&apps_smmu 0x808 0x0>,
+				 <&apps_smmu 0x810 0x8>,
+				 <&apps_smmu 0xc08 0x0>,
+				 <&apps_smmu 0xc10 0x8>;
+
+			power-domains = <&camcc IFE_0_GDSC>,
+					<&camcc IFE_1_GDSC>,
+					<&camcc TITAN_TOP_GDSC>;
+			power-domain-names = "ife0",
+					     "ife1",
+					     "top";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				camss_port0: port@0 {
+					reg = <0>;
+				};
Quoted 8 lines

arch/arm64/boot/dts/qcom/sdm670.dtsi spmi_bus: spmi@c440000 { · line 1582

Quoted 6 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +6 -0
+
+				camss_port1: port@1 {
+					reg = <1>;
+				};
+
+				camss_port2: port@2 {

Likely labels to ports are excessive here, please remove them.

How would you imagine connecting a camera to the ports, then? For MDSS, there's a label for the endpoint (mdss_dsi0_out) which the device DTS can then reference:

	&mdss_dsi0_out {
		remote-endpoint = <&panel_in>;
		data-lanes = <0 1 2 3>;
	};

For CAMSS, the port labels would be used like so:

	&camss_port1 {
		camss_endpoint1: endpoint {
			clock-lanes = <7>;
			data-lanes = <0 1 2 3>;
			remote-endpoint = <&cam_front_endpoint>;
		};
	};
Quoted 2 lines

Without the labels, the connection might look something like:

Even if you insist on moving endpoints out of &camss, then why do you add port labels? Unavoidably you do have endpoint labels, so it's non-obvious why the version above is better than the next one:

	&camss_endpoint1 {
		clock-lanes = <7>;
		data-lanes = <0 1 2 3>;
		remote-endpoint = <&cam_front_endpoint>;
	};

Minus two lines of code, minus one label. Port labels are not needed.

Quoted 17 lines
	&camss {
		status = "okay";

		// Modification of existing /soc/isp@acb3000/ports node
		ports {
			// Modification of existing /soc/isp@acb3000/ports/port@1 node
			port@1 {
				// New node
				camss_endpoint1: endpoint {
					clock-lanes = <7>;
					data-lanes = <0 1 2 3>;
					remote-endpoint = <&cam_front_endpoint>;
				};
			};
		};
	};
Quoted 1 line

which I believe is not preferred.

Well, that's exactly how it's done right at the moment, in other words it was preferred every time in the past.

--
Best wishes,
Vladimir

#14 lore raw

Re: [PATCH v8 5/5] arm64: dts: qcom: sdm670: add camss and cci

Quoted 248 lines · Vladimir Zapolskiy
Quoted 240 lines · Richard Acayan
Quoted 94 lines · Vladimir Zapolskiy

Hi Richard.

Quoted 91 lines · Richard Acayan

Add the camera subsystem and CCI used to interface with cameras on the Snapdragon 670.

---
   arch/arm64/boot/dts/qcom/sdm670.dtsi | 185 +++++++++++++++++++++++++++
   1 file changed, 185 insertions(+)
arch/arm64/boot/dts/qcom/sdm670.dtsi +63 -0
index 328096b91126..d4e1251ada04 100644
@@ -6,6 +6,7 @@
    * Copyright (c) 2022, Richard Acayan. All rights reserved.
    */
+#include <dt-bindings/clock/qcom,camcc-sdm845.h>
   #include <dt-bindings/clock/qcom,dispcc-sdm845.h>
   #include <dt-bindings/clock/qcom,gcc-sdm845.h>
   #include <dt-bindings/clock/qcom,rpmh.h>
@@ -1168,6 +1169,34 @@ tlmm: pinctrl@3400000 {
   			gpio-ranges = <&tlmm 0 0 151>;
   			wakeup-parent = <&pdc>;
+			cci0_default: cci0-default-state {
+				pins = "gpio17", "gpio18";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			cci0_sleep: cci0-sleep-state {
+				pins = "gpio17", "gpio18";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			cci1_default: cci1-default-state {
+				pins = "gpio19", "gpio20";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			cci1_sleep: cci1-sleep-state {
+				pins = "gpio19", "gpio20";
+				function = "cci_i2c";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
   			qup_i2c0_default: qup-i2c0-default-state {
   				pins = "gpio0", "gpio1";
   				function = "qup0";
@@ -1400,6 +1429,162 @@ spmi_bus: spmi@c440000 {
   			#interrupt-cells = <4>;
   		};
+		cci: cci@ac4a000 {
+			compatible = "qcom,sdm670-cci", "qcom,msm8996-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg = <0 0x0ac4a000 0 0x4000>;
+			interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
+			power-domains = <&camcc TITAN_TOP_GDSC>;
+
+			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_SOC_AHB_CLK>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_CCI_CLK>;
+			clock-names = "camnoc_axi",
+				      "soc_ahb",
+				      "cpas_ahb",
+				      "cci";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&cci0_default &cci1_default>;
+			pinctrl-1 = <&cci0_sleep &cci1_sleep>;
+
+			status = "disabled";
+
+			cci_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <1000000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			cci_i2c1: i2c-bus@1 {
+				reg = <1>;
+				clock-frequency = <1000000>;
Quoted 8 lines

arch/arm64/boot/dts/qcom/sdm670.dtsi spmi_bus: spmi@c440000 { · line 1471

Quoted 6 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +6 -0
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		camss: camera-controller@acb3000 {

Wasn't it agreed recently to have 'isp' as a generic device name for CAMSS IP?

Yeah, will change.

Quoted 106 lines
Quoted 106 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +105 -0
+			compatible = "qcom,sdm670-camss";
+			reg = <0 0x0acb3000 0 0x1000>,
+			      <0 0x0acba000 0 0x1000>,
+			      <0 0x0acc8000 0 0x1000>,
+			      <0 0x0ac65000 0 0x1000>,
+			      <0 0x0ac66000 0 0x1000>,
+			      <0 0x0ac67000 0 0x1000>,
+			      <0 0x0acaf000 0 0x4000>,
+			      <0 0x0acb6000 0 0x4000>,
+			      <0 0x0acc4000 0 0x4000>;
+			reg-names = "csid0",
+				    "csid1",
+				    "csid2",
+				    "csiphy0",
+				    "csiphy1",
+				    "csiphy2",
+				    "vfe0",
+				    "vfe1",
+				    "vfe_lite";
+
+			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_0_CSID_CLK>,
+				 <&camcc CAM_CC_IFE_1_CSID_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CSID_CLK>,
+				 <&camcc CAM_CC_CSIPHY0_CLK>,
+				 <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY1_CLK>,
+				 <&camcc CAM_CC_CSI1PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY2_CLK>,
+				 <&camcc CAM_CC_CSI2PHYTIMER_CLK>,
+				 <&gcc GCC_CAMERA_AHB_CLK>,
+				 <&gcc GCC_CAMERA_AXI_CLK>,
+				 <&camcc CAM_CC_SOC_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_0_CLK>,
+				 <&camcc CAM_CC_IFE_0_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_1_CLK>,
+				 <&camcc CAM_CC_IFE_1_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>;
+			clock-names = "camnoc_axi",
+				      "cpas_ahb",
+				      "csi0",
+				      "csi1",
+				      "csi2",
+				      "csiphy0",
+				      "csiphy0_timer",
+				      "csiphy1",
+				      "csiphy1_timer",
+				      "csiphy2",
+				      "csiphy2_timer",
+				      "gcc_camera_ahb",
+				      "gcc_camera_axi",
+				      "soc_ahb",
+				      "vfe0",
+				      "vfe0_axi",
+				      "vfe0_cphy_rx",
+				      "vfe1",
+				      "vfe1_axi",
+				      "vfe1_cphy_rx",
+				      "vfe_lite",
+				      "vfe_lite_cphy_rx";
+
+			interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "csid0",
+					  "csid1",
+					  "csid2",
+					  "csiphy0",
+					  "csiphy1",
+					  "csiphy2",
+					  "vfe0",
+					  "vfe1",
+					  "vfe_lite";
+
+			iommus = <&apps_smmu 0x808 0x0>,
+				 <&apps_smmu 0x810 0x8>,
+				 <&apps_smmu 0xc08 0x0>,
+				 <&apps_smmu 0xc10 0x8>;
+
+			power-domains = <&camcc IFE_0_GDSC>,
+					<&camcc IFE_1_GDSC>,
+					<&camcc TITAN_TOP_GDSC>;
+			power-domain-names = "ife0",
+					     "ife1",
+					     "top";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				camss_port0: port@0 {
+					reg = <0>;
+				};
Quoted 8 lines

arch/arm64/boot/dts/qcom/sdm670.dtsi spmi_bus: spmi@c440000 { · line 1582

Quoted 6 lines
arch/arm64/boot/dts/qcom/sdm670.dtsi +6 -0
+
+				camss_port1: port@1 {
+					reg = <1>;
+				};
+
+				camss_port2: port@2 {

Likely labels to ports are excessive here, please remove them.

How would you imagine connecting a camera to the ports, then? For MDSS, there's a label for the endpoint (mdss_dsi0_out) which the device DTS can then reference:

	&mdss_dsi0_out {
		remote-endpoint = <&panel_in>;
		data-lanes = <0 1 2 3>;
	};

For CAMSS, the port labels would be used like so:

	&camss_port1 {
		camss_endpoint1: endpoint {
			clock-lanes = <7>;
			data-lanes = <0 1 2 3>;
			remote-endpoint = <&cam_front_endpoint>;
		};
	};
Quoted 2 lines

Without the labels, the connection might look something like:

Even if you insist on moving endpoints out of &camss, then why do you add port labels? Unavoidably you do have endpoint labels, so it's non-obvious why the version above is better than the next one:

Quoted 7 lines
	&camss_endpoint1 {
		clock-lanes = <7>;
		data-lanes = <0 1 2 3>;
		remote-endpoint = <&cam_front_endpoint>;
	};

Minus two lines of code, minus one label. Port labels are not needed.

Thanks for having me look into this.

In DTSI:

	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		camss_port0: port@0 {
			reg = <0>;

			camss_endpoint0: endpoint {
			};
		};

		camss_port1: port@1 {
			reg = <1>;

			camss_endpoint1: endpoint {
			};
		};

		camss_port2: port@2 {
			reg = <2>;

			camss_endpoint2: endpoint {
			};
		};
	};

The example above doesn't work as-is.

	[   15.387215] qcom-camss acb3000.camera-controller: Cannot get remote parent
	[   15.387604] qcom-camss acb3000.camera-controller: probe with driver qcom-camss failed with error -22

However, the camss_of_parse_ports function has a way to make it work, even if all endpoint nodes are present.

In DTSI:

	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		camss_port0: port@0 {
			reg = <0>;

			camss_endpoint0: endpoint {
				status = "disabled";
			};
		};

		camss_port1: port@1 {
			reg = <1>;

			camss_endpoint1: endpoint {
				status = "disabled";
			};
		};

		camss_port2: port@2 {
			reg = <2>;

			camss_endpoint2: endpoint {
				status = "disabled";
			};
		};
	};

In DTS:

&camss_endpoint1 {
clock-lanes = <7>;
data-lanes = <0 1 2 3>;

 		remote-endpoint = <&cam_front_endpoint>;
		status = "okay";

};

I didn't know how to make the working example.