Skip to contentSkip to conversation

bnxt_en: implement tcp-data-split and thresh option

PATCH Superseded Taehee Yoo 4 participants 34 messages Dec 18, 2024 – Dec 20, 2024

Subsystems (8)

v6 of 9 Superseded Latest is v9 →

lore
Share & tools
lore

Taehee Yoo

author
#0 lore raw

v6 cover bnxt_en: implement tcp-data-split and thresh option

This series implements hds-thresh ethtool command.
This series also implements backend of tcp-data-split and hds-thresh ethtool command for bnxt_en driver.
These ethtool commands are mandatory options for device memory TCP.

NICs that use the bnxt_en driver support tcp-data-split feature named HDS(header-data-split).
But there is no implementation for the HDS to enable by ethtool. Only getting the current HDS status is implemented and the HDS is just automatically enabled only when either LRO, HW-GRO, or JUMBO is enabled. The hds_threshold follows the rx-copybreak value but it wasn't changeable.

Currently, bnxt_en driver enables tcp-data-split by default but not always work.
There is hds_threshold value, which indicates that a packet size is larger than this value, a packet will be split into header and data. hds_threshold value has been 256, which is a default value of rx-copybreak value too.
The rx-copybreak value hasn't been allowed to change so the hds_threshold too.

This patchset decouples hds_threshold and rx-copybreak first. and make tcp-data-split, rx-copybreak, and hds-thresh configurable independently.

But the default configuration is the same. The default value of rx-copybreak is 256 and default hds-thresh is also 256.

The behavior of rx-copybreak will probably be changed in almost all drivers. If HDS is not enabled, rx-copybreak copies both header and payload from a page.
But if HDS is enabled, rx-copybreak copies only header from the first page.
Due to this change, it may need to disable(set to 0) rx-copybreak when the HDS is required.

There are several related options.
TPA(HW-GRO, LRO), JUMBO, jumbo_thresh(firmware command), and Aggregation Ring.

The aggregation ring is fundamental to these all features. When gro/lro/jumbo packets are received, NIC receives the first packet from the normal ring.
follow packets come from the aggregation ring.

These features are working regardless of HDS.
If HDS is enabled, the first packet contains the header only, and the following packets contain only payload.
So, HW-GRO/LRO is working regardless of HDS.

There is another threshold value, which is jumbo_thresh.
This is very similar to hds_thresh, but jumbo thresh doesn't split header and data.
It just split the first and following data based on length. When NIC receives 1500 sized packet, and jumbo_thresh is 256(default, but follows rx-copybreak),
the first data is 256 and the following packet size is 1500-256.

Before this patch, at least if one of GRO, LRO, and JUMBO flags is enabled, the Aggregation ring will be enabled.
If the Aggregation ring is enabled, both hds_threshold and jumbo_thresh are set to the default value of rx-copybreak.

So, GRO, LRO, JUMBO frames, they larger than 256 bytes, they will be split into header and data if the protocol is TCP or UDP. for the other protocol, jumbo_thresh works instead of hds_thresh.

This means that tcp-data-split relies on the GRO, LRO, and JUMBO flags. But by this patch, tcp-data-split no longer relies on these flags. If the tcp-data-split is enabled, the Aggregation ring will be enabled.
Also, hds_threshold no longer follows rx-copybreak value, it will be set to the hds-thresh value by user-space, but the default value is still 256.

If the protocol is TCP or UDP and the HDS is disabled and Aggregation ring is enabled, a packet will be split into several pieces due to jumbo_thresh.

When single buffer XDP is attached, tcp-data-split is automatically disabled.

LRO, GRO, and JUMBO are tested with BCM57414, BCM57504 and the firmware version is 230.0.157.0.
I couldn't find any specification about minimum and maximum value of hds_threshold, but from my test result, it was about 0 ~ 1023. It means, over 1023 sized packets will be split into header and data if tcp-data-split is enabled regardless of hds_treshold value. When hds_threshold is 1500 and received packet size is 1400, HDS should not be activated, but it is activated.
The maximum value of hds-thresh value is 256 because it
has been working. It was decided very conservatively.

I checked out the tcp-data-split(HDS) works independently of GRO, LRO, JUMBO.
Also, I checked out tcp-data-split should be disabled automatically when XDP is attached and disallowed to enable it again while XDP is attached. I tested ranged values from min to max for hds-thresh and rx-copybreak, and it works.
hds-thresh from 0 to 256, and rx-copybreak 0 to 256.
When testing this patchset, I checked skb->data, skb->data_len, and nr_frags values.

By this patchset, bnxt_en driver supports a force enable tcp-data-split, but it doesn't support for disable tcp-data-split.
When tcp-data-split is explicitly enabled, HDS works always. When tcp-data-split is unknown, it depends on the current configuration of LRO/GRO/JUMBO.

1/9 patch implements .{set, get}_tunable() in the bnxt_en. The bnxt_en driver has been supporting the rx-copybreak feature but is not configurable, Only the default rx-copybreak value has been working. So, it changes the bnxt_en driver to be able to configure the rx-copybreak value.

2/9 patch adds a new hds_config member in the ethtool_netdev_state. It indicates that what tcp-data-split value is really updated from userspace.
So the driver can distinguish a passed tcp-data-split value is came from user or driver itself.

3/9 patch adds an implementation of tcp-data-split ethtool command.
The HDS relies on the Aggregation ring, which is automatically enabled when either LRO, GRO, or large mtu is configured.
So, if the Aggregation ring is enabled, HDS is automatically enabled by it.

4/9 patch adds hds-thresh command in the ethtool.
This threshold value indicates if a received packet size is larger than this threshold, the packet's header and payload will be split. Example:

   # ethtool -G <interface name> hds-thresh <value>
This option can not be used when tcp-data-split is disabled or not
supported.
   # ethtool -G enp14s0f0np0 tcp-data-split on hds-thresh 256
   # ethtool -g enp14s0f0np0
   Ring parameters for enp14s0f0np0:
   Pre-set maximums:
   ...
   Current hardware settings:
   ...
   TCP data split:         on
   HDS thresh:  256

5/9 patch adds the implementation of hds-thresh logic
in the bnxt_en driver.
The default value is 256, which used to be the default rx-copybreak value.

6/9, 7/9 add condition checks for devmem and ethtool.
If tcp-data-split is disabled or threshold value is not zero, setup of devmem will be failed.
Also, tcp-data-split and hds-thresh will not be changed while devmem is running.

8/9 add condition checks for netdev core.
It disallows setup single buffer XDP program when tcp-data-split is enabled.

9/9 add HDS feature implementation for netdevsim.
HDS feature is not common so far. Only a few NICs support this feature. There is no way to test HDS core-API unless we have proper hw NIC. In order to test HDS core-API without hw NIC, netdevsim can be used. So, implements HDS contronplane for netdevsim.

This series is tested with BCM57504 and netdevsim.

v6:
- use hds_config instead of tcp_data_split_mod.
- Disallow to attach XDP when HDS is in use.
- Update ethtool_netlink_generated.h
- Use "HDS" instead of "HEADER_DATA_SPLIT"
- HDS_MAX is changed to 1023.
- Implement netdevsim HDS feature.
- Add Test tags from Andy.

v5:
- Remove netdev_devmem_enabled() and use dev_get_min_mp_channel_count() instead.
- change extack messages
- Drop implementation of device memory TCP for bnxt_en.
- Add Review tags from Mina.

v4:
- Remove min rx-copybreak value.
- Do not support a disable of tcp-data-split by bnxt_en driver.
- Rename from tcp-data-split-thresh to hds-thresh.
- Add ETHTOOL_RING_USE_HDS_THRS flag.
- Add dev_xdp_sb_prog_count() helper.
- Reduce hole in struct bnxt.
- Use ETHTOOL_RING_USE_HDS_THRS in bnxt_en driver.
- Improve condition check.
- Add netdev_devmem_enabled() helper.
- Add netmem_is_pfmemalloc() helper.
- Do not select NET_DEVMEM in Kconfig for bnxt_en driver.
- Pass PP_FLAG_ALLOW_UNREADABLE_NETMEM flag unconditionally.
- Use gfp flag in __bnxt_alloc_rx_netmem() in the last patch.
- Do not add *offset in the __bnxt_alloc_rx_netmem() in the last patch.
- Do not pass queue_idx to bnxt_alloc_rx_page_pool() in the last patch.
- Add Test tag from Stanislav.
- Add Review tag from Brett.
- Add page_pool_recycle_direct_netmem() helper

v3:
- Change headline
- Add condition checks for ethtool and devmem
- Fix documentation
- Move validation of tcp-data-split and thresh from dirver to core API
- Add implementation of device memory TCP for bnxt_en driver

v2:
- Add tcp-data-split-thresh ethtool command
- Implement tcp-data-split-threh in the bnxt_en driver
- Define min/max rx-copybreak value
- Update commit message

Taehee Yoo (9):
bnxt_en: add support for rx-copybreak ethtool command
net: ethtool: add hds_config member in ethtool_netdev_state
bnxt_en: add support for tcp-data-split ethtool command
net: ethtool: add support for configuring hds-thresh
bnxt_en: add support for hds-thresh ethtool command
net: devmem: add ring parameter filtering
net: ethtool: add ring parameter filtering
net: disallow setup single buffer XDP when tcp-data-split is enabled.
netdevsim: add HDS feature

 Documentation/netlink/specs/ethtool.yaml      |  8 ++
 Documentation/networking/ethtool-netlink.rst  | 10 +++
 drivers/net/ethernet/broadcom/bnxt/bnxt.c     | 31 ++++----
 drivers/net/ethernet/broadcom/bnxt/bnxt.h     | 12 ++-
 .../net/ethernet/broadcom/bnxt/bnxt_ethtool.c | 75 ++++++++++++++++++-
 drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c |  4 +
 drivers/net/netdevsim/ethtool.c               | 15 +++-
 drivers/net/netdevsim/netdevsim.h             |  4 +
 include/linux/ethtool.h                       |  8 ++
 include/linux/netdevice.h                     |  1 +
 .../uapi/linux/ethtool_netlink_generated.h    |  2 +
 net/core/dev.c                                | 29 +++++++
 net/core/devmem.c                             | 19 +++++
 net/ethtool/netlink.h                         |  2 +-
 net/ethtool/rings.c                           | 55 +++++++++++++-
 15 files changed, 254 insertions(+), 21 deletions(-)
Signature · 1 line
2.34.1
author
#1 lore raw

PATCH v6 1/9 bnxt_en: add support for rx-copybreak ethtool command

The bnxt_en driver supports rx-copybreak, but it couldn't be set by userspace. Only the default value(256) has worked.
This patch makes the bnxt_en driver support following command. ethtool --set-tunable <devname> rx-copybreak <value> and ethtool --get-tunable <devname> rx-copybreak.

By this patch, hds_threshol is set to the rx-copybreak value. But it will be set by ethtool -G eth0 hds-thresh N in the next patch.

---

v6:
- No changes.

v5:
- Do not set HDS if XDP is attached.
- rx_size and pkt_size are always bigger than 256.

v4:
- Remove min rx-copybreak value.
- Add Review tag from Brett.
- Add Test tag from Stanislav.

v3:
- Update copybreak value after closing nic and before opening nic when the device is running.

v2:
- Define max/vim rx_copybreak value.

 drivers/net/ethernet/broadcom/bnxt/bnxt.c     | 28 ++++++-----
 drivers/net/ethernet/broadcom/bnxt/bnxt.h     |  5 +-
 .../net/ethernet/broadcom/bnxt/bnxt_ethtool.c | 49 ++++++++++++++++++-
 3 files changed, 68 insertions(+), 14 deletions(-)
drivers/net/ethernet/broadcom/bnxt/bnxt.c +16 -12
index b86f980fa7ea..c31894b9187e 100644
@@ -81,7 +81,6 @@ MODULE_DESCRIPTION("Broadcom NetXtreme network driver");
 
 #define BNXT_RX_OFFSET (NET_SKB_PAD + NET_IP_ALIGN)
 #define BNXT_RX_DMA_OFFSET NET_SKB_PAD
-#define BNXT_RX_COPY_THRESH 256
 
 #define BNXT_TX_PUSH_THRESH 164
 
@@ -1343,13 +1342,13 @@ static struct sk_buff *bnxt_copy_data(struct bnxt_napi *bnapi, u8 *data,
 	if (!skb)
 		return NULL;
 
-	dma_sync_single_for_cpu(&pdev->dev, mapping, bp->rx_copy_thresh,
+	dma_sync_single_for_cpu(&pdev->dev, mapping, bp->rx_copybreak,
 				bp->rx_dir);
 
 	memcpy(skb->data - NET_IP_ALIGN, data - NET_IP_ALIGN,
 	       len + NET_IP_ALIGN);
 
-	dma_sync_single_for_device(&pdev->dev, mapping, bp->rx_copy_thresh,
+	dma_sync_single_for_device(&pdev->dev, mapping, bp->rx_copybreak,
 				   bp->rx_dir);
 
 	skb_put(skb, len);
@@ -1842,7 +1841,7 @@ static inline struct sk_buff *bnxt_tpa_end(struct bnxt *bp,
 		return NULL;
 	}
 
-	if (len <= bp->rx_copy_thresh) {
+	if (len <= bp->rx_copybreak) {
 		skb = bnxt_copy_skb(bnapi, data_ptr, len, mapping);
 		if (!skb) {
 			bnxt_abort_tpa(cpr, idx, agg_bufs);
@@ -2176,7 +2175,7 @@ static int bnxt_rx_pkt(struct bnxt *bp, struct bnxt_cp_ring_info *cpr,
 		}
 	}
 
-	if (len <= bp->rx_copy_thresh) {
+	if (len <= bp->rx_copybreak) {
 		if (!xdp_active)
 			skb = bnxt_copy_skb(bnapi, data_ptr, len, dma_addr);
 		else
@@ -4601,6 +4600,11 @@ void bnxt_set_tpa_flags(struct bnxt *bp)
 		bp->flags |= BNXT_FLAG_GRO;
 }
 
+static void bnxt_init_ring_params(struct bnxt *bp)
+{
+	bp->rx_copybreak = BNXT_DEFAULT_RX_COPYBREAK;
+}
+
 /* bp->rx_ring_size, bp->tx_ring_size, dev->mtu, BNXT_FLAG_{G|L}RO flags must
  * be set on entry.
  */
@@ -4615,7 +4619,6 @@ void bnxt_set_ring_params(struct bnxt *bp)
 	rx_space = rx_size + ALIGN(max(NET_SKB_PAD, XDP_PACKET_HEADROOM), 8) +
 		SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
 
-	bp->rx_copy_thresh = BNXT_RX_COPY_THRESH;
 	ring_size = bp->rx_ring_size;
 	bp->rx_agg_ring_size = 0;
 	bp->rx_agg_nr_pages = 0;
@@ -4660,7 +4663,9 @@ void bnxt_set_ring_params(struct bnxt *bp)
 				  ALIGN(max(NET_SKB_PAD, XDP_PACKET_HEADROOM), 8) -
 				  SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
 		} else {
-			rx_size = SKB_DATA_ALIGN(BNXT_RX_COPY_THRESH + NET_IP_ALIGN);
+			rx_size = SKB_DATA_ALIGN(max(BNXT_DEFAULT_RX_COPYBREAK,
+						     bp->rx_copybreak) +
+						 NET_IP_ALIGN);
 			rx_space = rx_size + NET_SKB_PAD +
 				SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
 		}
@@ -6566,16 +6571,14 @@ static int bnxt_hwrm_vnic_set_hds(struct bnxt *bp, struct bnxt_vnic_info *vnic)
 
 	req->flags = cpu_to_le32(VNIC_PLCMODES_CFG_REQ_FLAGS_JUMBO_PLACEMENT);
 	req->enables = cpu_to_le32(VNIC_PLCMODES_CFG_REQ_ENABLES_JUMBO_THRESH_VALID);
+	req->jumbo_thresh = cpu_to_le16(bp->rx_buf_use_size);
 
-	if (BNXT_RX_PAGE_MODE(bp)) {
-		req->jumbo_thresh = cpu_to_le16(bp->rx_buf_use_size);
-	} else {
+	if (!BNXT_RX_PAGE_MODE(bp) && (bp->flags & BNXT_FLAG_AGG_RINGS)) {
 		req->flags |= cpu_to_le32(VNIC_PLCMODES_CFG_REQ_FLAGS_HDS_IPV4 |
 					  VNIC_PLCMODES_CFG_REQ_FLAGS_HDS_IPV6);
 		req->enables |=
 			cpu_to_le32(VNIC_PLCMODES_CFG_REQ_ENABLES_HDS_THRESHOLD_VALID);
-		req->jumbo_thresh = cpu_to_le16(bp->rx_copy_thresh);
-		req->hds_threshold = cpu_to_le16(bp->rx_copy_thresh);
+		req->hds_threshold = cpu_to_le16(bp->rx_copybreak);
 	}
 	req->vnic_id = cpu_to_le32(vnic->fw_vnic_id);
 	return hwrm_req_send(bp, req);
@@ -16188,6 +16191,7 @@ static int bnxt_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	bnxt_init_l2_fltr_tbl(bp);
 	bnxt_set_rx_skb_mode(bp, false);
 	bnxt_set_tpa_flags(bp);
+	bnxt_init_ring_params(bp);
 	bnxt_set_ring_params(bp);
 	bnxt_rdma_aux_device_init(bp);
 	rc = bnxt_set_dflt_rings(bp, true);
drivers/net/ethernet/broadcom/bnxt/bnxt.h +4 -1
index 7df7a2233307..b73de5683063 100644
@@ -34,6 +34,9 @@
 #include <linux/firmware/broadcom/tee_bnxt_fw.h>
 #endif
 
+#define BNXT_DEFAULT_RX_COPYBREAK 256
+#define BNXT_MAX_RX_COPYBREAK 1024
+
 extern struct list_head bnxt_block_cb_list;
 
 struct page_pool;
@@ -2342,7 +2345,7 @@ struct bnxt {
 	enum dma_data_direction	rx_dir;
 	u32			rx_ring_size;
 	u32			rx_agg_ring_size;
-	u32			rx_copy_thresh;
+	u32			rx_copybreak;
 	u32			rx_ring_mask;
 	u32			rx_agg_ring_mask;
 	int			rx_nr_pages;
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c +48 -1

67 lines not on this page · raw message

Signature · 1 line
2.34.1
maintainer
#2 lore raw

Re: [PATCH net-next v6 1/9] bnxt_en: add support for rx-copybreak ethtool command

drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c static int bnxt_get_eee(struct net_device *dev, struct ethtool_keee *edata) · line 4347

Quoted 5 lines · On Wed, 18 Dec 2024 14:45:22 +0000 Taehee Yoo wrote:
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c +5 -0
+			if (netif_running(dev)) {
+				bnxt_close_nic(bp, false, false);
+				bp->rx_copybreak = rx_copybreak;
+				bnxt_set_ring_params(bp);
+				bnxt_open_nic(bp, false, false);

We really shouldn't allow this any more, we've been rejecting patches which try to accept reconfiguration requests by taking the entire NIC down, without any solid recovery if memory allocation fails.

Let's return -EBUSY if interface is running.

author
#3 lore raw

Re: [PATCH net-next v6 1/9] bnxt_en: add support for rx-copybreak ethtool command

Quoted 1 line · Jakub Kicinski

Hi Jakub,
Thanks a lot for the review!

Quoted 7 lines · On Wed, 18 Dec 2024 14:45:22 +0000 Taehee Yoo wrote:

drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c static int bnxt_get_eee(struct net_device *dev, struct ethtool_keee *edata) · line 4347

Quoted 5 lines
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c +5 -0
+                     if (netif_running(dev)) {
+                             bnxt_close_nic(bp, false, false);
+                             bp->rx_copybreak = rx_copybreak;
+                             bnxt_set_ring_params(bp);
+                             bnxt_open_nic(bp, false, false);
Quoted 6 lines

We really shouldn't allow this any more, we've been rejecting patches which try to accept reconfiguration requests by taking the entire NIC down, without any solid recovery if memory allocation fails.

Let's return -EBUSY if interface is running.

Okay, I will change it.

Thanks a lot,
Taehee Yoo

author
#4 lore raw

PATCH v6 2/9 net: ethtool: add hds_config member in ethtool_netdev_state

In reply to Taehee Yoo

When tcp-data-split is UNKNOWN mode, drivers arbitrarily handle it. For example, bnxt_en driver automatically enables if at least one of LRO/GRO/JUMBO is enabled.
If tcp-data-split is UNKNOWN and LRO is enabled, a driver returns ENABLES of tcp-data-split, not UNKNOWN.
So, ethtool -g eth0 shows tcp-data-split is enabled.

The problem is in the setting situation.
In the ethnl_set_rings(), it first calls get_ringparam() to get the current driver's config.
At that moment, if driver's tcp-data-split config is UNKNOWN, it returns ENABLE if LRO/GRO/JUMBO is enabled.
Then, it sets values from the user and driver's current config to kernel_ethtool_ringparam.
Last it calls .set_ringparam().
The driver, especially bnxt_en driver receives ETHTOOL_TCP_DATA_SPLIT_ENABLED.
But it can't distinguish whether it is set by the user or just the current config.

When user updates ring parameter, the new hds_config value is updated and current hds_config value is stored to old_hdsconfig. Driver's .set_ringparam() callback can distinguish a passed tcp-data-split value is came from user explicitly.
If .set_ringparam() is failed, hds_config is rollbacked immediately.

---

v6:
- use hds_config instead of using tcp_data_split_mod.

v5:
- Patch added.

 include/linux/ethtool.h | 2 ++
 net/ethtool/rings.c     | 4 ++++
 2 files changed, 6 insertions(+)
include/linux/ethtool.h +2 -0
index f711bfd75c4d..4e451084d58a 100644
@@ -1134,12 +1134,14 @@ int ethtool_virtdev_set_link_ksettings(struct net_device *dev,
  * @rss_ctx:		XArray of custom RSS contexts
  * @rss_lock:		Protects entries in @rss_ctx.  May be taken from
  *			within RTNL.
+ * @hds_config:		HDS value from userspace.
  * @wol_enabled:	Wake-on-LAN is enabled
  * @module_fw_flash_in_progress: Module firmware flashing is in progress.
  */
 struct ethtool_netdev_state {
 	struct xarray		rss_ctx;
 	struct mutex		rss_lock;
+	u8			hds_config;
 	unsigned		wol_enabled:1;
 	unsigned		module_fw_flash_in_progress:1;
 };
net/ethtool/rings.c +4 -0
index b7865a14fdf8..2e8239a76234 100644
@@ -203,6 +203,7 @@ ethnl_set_rings(struct ethnl_req_info *req_info, struct genl_info *info)
 
 	dev->ethtool_ops->get_ringparam(dev, &ringparam,
 					&kernel_ringparam, info->extack);
+	kernel_ringparam.tcp_data_split = dev->ethtool->hds_config;
 
 	ethnl_update_u32(&ringparam.rx_pending, tb[ETHTOOL_A_RINGS_RX], &mod);
 	ethnl_update_u32(&ringparam.rx_mini_pending,
@@ -252,6 +253,9 @@ ethnl_set_rings(struct ethnl_req_info *req_info, struct genl_info *info)
 
 	ret = dev->ethtool_ops->set_ringparam(dev, &ringparam,
 					      &kernel_ringparam, info->extack);
+	if (!ret)
+		dev->ethtool->hds_config = kernel_ringparam.tcp_data_split;
+
 	return ret < 0 ? ret : 1;
 }
 
Signature · 1 line
2.34.1
maintainer Reviewed-by on v6 2/9
#5 lore raw

Re: [PATCH net-next v6 2/9] net: ethtool: add hds_config member in ethtool_netdev_state

Quoted 20 lines · On Wed, 18 Dec 2024 14:45:23 +0000 Taehee Yoo wrote:

When tcp-data-split is UNKNOWN mode, drivers arbitrarily handle it. For example, bnxt_en driver automatically enables if at least one of LRO/GRO/JUMBO is enabled.
If tcp-data-split is UNKNOWN and LRO is enabled, a driver returns ENABLES of tcp-data-split, not UNKNOWN.
So, ethtool -g eth0 shows tcp-data-split is enabled.

The problem is in the setting situation.
In the ethnl_set_rings(), it first calls get_ringparam() to get the current driver's config.
At that moment, if driver's tcp-data-split config is UNKNOWN, it returns ENABLE if LRO/GRO/JUMBO is enabled.
Then, it sets values from the user and driver's current config to kernel_ethtool_ringparam.
Last it calls .set_ringparam().
The driver, especially bnxt_en driver receives ETHTOOL_TCP_DATA_SPLIT_ENABLED.
But it can't distinguish whether it is set by the user or just the current config.

Quoted 8 lines

When user updates ring parameter, the new hds_config value is updated and current hds_config value is stored to old_hdsconfig. Driver's .set_ringparam() callback can distinguish a passed tcp-data-split value is came from user explicitly.
If .set_ringparam() is failed, hds_config is rollbacked immediately.

author
#6 lore raw

PATCH v6 3/9 bnxt_en: add support for tcp-data-split ethtool command

In reply to Taehee Yoo

NICs that uses bnxt_en driver supports tcp-data-split feature by the name of HDS(header-data-split).
But there is no implementation for the HDS to enable by ethtool. Only getting the current HDS status is implemented and The HDS is just automatically enabled only when either LRO, HW-GRO, or JUMBO is enabled. The hds_threshold follows rx-copybreak value. and it was unchangeable.

This implements ethtool -G <interface name> tcp-data-split <value> command option.
The value can be <on> and <auto>.
The value is <auto> and one of LRO/GRO/JUMBO is enabled, HDS is automatically enabled and all LRO/GRO/JUMBO are disabled, HDS is automatically disabled.

HDS feature relies on the aggregation ring.
So, if HDS is enabled, the bnxt_en driver initializes the aggregation ring. This is the reason why BNXT_FLAG_AGG_RINGS contains HDS condition.

---

v6:
- Disallow to attach XDP when HDS is in use.
- Add Test tag from Andy.

v5:
- Do not set HDS if XDP is attached.
- Enable tcp-data-split only when tcp_data_split_mod is true.

v4:
- Do not support disable tcp-data-split.
- Add Test tag from Stanislav.

v3:
- No changes.

v2:
- Do not set hds_threshold to 0.

 drivers/net/ethernet/broadcom/bnxt/bnxt.c     |  2 +-
 drivers/net/ethernet/broadcom/bnxt/bnxt.h     |  5 +++--
 .../net/ethernet/broadcom/bnxt/bnxt_ethtool.c | 21 +++++++++++++++++++
 drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c |  4 ++++
 4 files changed, 29 insertions(+), 3 deletions(-)
drivers/net/ethernet/broadcom/bnxt/bnxt.c +1 -1
index c31894b9187e..42ffaa88ae4e 100644
@@ -4623,7 +4623,7 @@ void bnxt_set_ring_params(struct bnxt *bp)
 	bp->rx_agg_ring_size = 0;
 	bp->rx_agg_nr_pages = 0;
 
-	if (bp->flags & BNXT_FLAG_TPA)
+	if (bp->flags & BNXT_FLAG_TPA || bp->flags & BNXT_FLAG_HDS)
 		agg_factor = min_t(u32, 4, 65536 / BNXT_RX_PAGE_SIZE);
 
 	bp->flags &= ~BNXT_FLAG_JUMBO;
drivers/net/ethernet/broadcom/bnxt/bnxt.h +3 -2
index b73de5683063..847dedf61a9e 100644
@@ -2244,8 +2244,6 @@ struct bnxt {
 	#define BNXT_FLAG_TPA		(BNXT_FLAG_LRO | BNXT_FLAG_GRO)
 	#define BNXT_FLAG_JUMBO		0x10
 	#define BNXT_FLAG_STRIP_VLAN	0x20
-	#define BNXT_FLAG_AGG_RINGS	(BNXT_FLAG_JUMBO | BNXT_FLAG_GRO | \
-					 BNXT_FLAG_LRO)
 	#define BNXT_FLAG_RFS		0x100
 	#define BNXT_FLAG_SHARED_RINGS	0x200
 	#define BNXT_FLAG_PORT_STATS	0x400
@@ -2266,6 +2264,9 @@ struct bnxt {
 	#define BNXT_FLAG_ROCE_MIRROR_CAP	0x4000000
 	#define BNXT_FLAG_TX_COAL_CMPL	0x8000000
 	#define BNXT_FLAG_PORT_STATS_EXT	0x10000000
+	#define BNXT_FLAG_HDS		0x20000000
+	#define BNXT_FLAG_AGG_RINGS	(BNXT_FLAG_JUMBO | BNXT_FLAG_GRO | \
+					 BNXT_FLAG_LRO | BNXT_FLAG_HDS)
 
 	#define BNXT_FLAG_ALL_CONFIG_FEATS (BNXT_FLAG_TPA |		\
 					    BNXT_FLAG_RFS |		\
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c +21 -0
index 4cdfff5d531c..25eb5931aea9 100644
@@ -840,16 +840,36 @@ static int bnxt_set_ringparam(struct net_device *dev,
 			      struct kernel_ethtool_ringparam *kernel_ering,
 			      struct netlink_ext_ack *extack)
 {
+	u8 tcp_data_split = kernel_ering->tcp_data_split;
 	struct bnxt *bp = netdev_priv(dev);
+	u8 hds_config_mod;
+
+	hds_config_mod = tcp_data_split != dev->ethtool->hds_config;
 
 	if ((ering->rx_pending > BNXT_MAX_RX_DESC_CNT) ||
 	    (ering->tx_pending > BNXT_MAX_TX_DESC_CNT) ||
 	    (ering->tx_pending < BNXT_MIN_TX_DESC_CNT))
 		return -EINVAL;
 
+	if (tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_DISABLED && hds_config_mod)
+		return -EOPNOTSUPP;
+
+	if (tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_ENABLED &&
+	    hds_config_mod && BNXT_RX_PAGE_MODE(bp)) {
+		NL_SET_ERR_MSG_MOD(extack, "tcp-data-split is disallowed when XDP is attached");
+		return -EOPNOTSUPP;
+	}
+
 	if (netif_running(dev))
 		bnxt_close_nic(bp, false, false);
 
+	if (hds_config_mod) {
+		if (tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_ENABLED)
+			bp->flags |= BNXT_FLAG_HDS;
+		else if (tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_UNKNOWN)
+			bp->flags &= ~BNXT_FLAG_HDS;
+	}
+
 	bp->rx_ring_size = ering->rx_pending;
 	bp->tx_ring_size = ering->tx_pending;
 	bnxt_set_ring_params(bp);
@@ -5354,6 +5374,7 @@ const struct ethtool_ops bnxt_ethtool_ops = {
 				     ETHTOOL_COALESCE_STATS_BLOCK_USECS |
 				     ETHTOOL_COALESCE_USE_ADAPTIVE_RX |
 				     ETHTOOL_COALESCE_USE_CQE,
+	.supported_ring_params	= ETHTOOL_RING_USE_TCP_DATA_SPLIT,
 	.get_link_ksettings	= bnxt_get_link_ksettings,
 	.set_link_ksettings	= bnxt_set_link_ksettings,
 	.get_fec_stats		= bnxt_get_fec_stats,
drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c +4 -0
index f88b641533fc..1bfff7f29310 100644
@@ -395,6 +395,10 @@ static int bnxt_xdp_set(struct bnxt *bp, struct bpf_prog *prog)
 			    bp->dev->mtu, BNXT_MAX_PAGE_MODE_MTU);
 		return -EOPNOTSUPP;
 	}
+	if (prog && bp->flags & BNXT_FLAG_HDS) {
+		netdev_warn(dev, "XDP is disallowed when HDS is enabled.\n");
+		return -EOPNOTSUPP;
+	}
 	if (!(bp->flags & BNXT_FLAG_SHARED_RINGS)) {
 		netdev_warn(dev, "ethtool rx/tx channels must be combined to support XDP.\n");
 		return -EOPNOTSUPP;
Signature · 1 line
2.34.1
maintainer
#7 lore raw

Re: [PATCH net-next v6 3/9] bnxt_en: add support for tcp-data-split ethtool command

Review

Quoted 2 lines · On Wed, 18 Dec 2024 14:45:24 +0000 Taehee Yoo wrote:
(quoted diff) +2 -0
+	if (tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_DISABLED && hds_config_mod)
+		return -EOPNOTSUPP;

I think ethtool ops generally return -EINVAL when param not supported. EOPNOTSUPP means entire op is not supported (again, that's just how ethtool ops generally work, not a kernel-wide rule).

drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c static int bnxt_set_ringparam(struct net_device *dev, · line 858

Quoted 2 lines
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c +2 -0
+	if (tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_ENABLED &&
+	    hds_config_mod && BNXT_RX_PAGE_MODE(bp)) {

Looks like patch 4 adds this check in the core. I think adding the check in the core can be a separate patch. If you put it before this patch in the series this bnxt check can be removed?

I mean this chunk in the core:

+ hds_config_mod = old_hds_config != kernel_ringparam.tcp_data_split;
+ if (kernel_ringparam.tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_ENABLED &&
+ hds_config_mod && dev_xdp_sb_prog_count(dev)) {
+ NL_SET_ERR_MSG(info->extack,
+ "tcp-data-split can not be enabled with single buffer XDP");
+ return -EINVAL;
+ }

It's currently in the hds-thresh patch but really it's unrelated to the threshold..

Quoted 30 lines
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c +12 -0
+		NL_SET_ERR_MSG_MOD(extack, "tcp-data-split is disallowed when XDP is attached");
+		return -EOPNOTSUPP;
+	}
+
 	if (netif_running(dev))
 		bnxt_close_nic(bp, false, false);
 
+	if (hds_config_mod) {
+		if (tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_ENABLED)
+			bp->flags |= BNXT_FLAG_HDS;
+		else if (tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_UNKNOWN)
+			bp->flags &= ~BNXT_FLAG_HDS;
+	}
+
 	bp->rx_ring_size = ering->rx_pending;
 	bp->tx_ring_size = ering->tx_pending;
 	bnxt_set_ring_params(bp);
@@ -5354,6 +5374,7 @@ const struct ethtool_ops bnxt_ethtool_ops = {
 				     ETHTOOL_COALESCE_STATS_BLOCK_USECS |
 				     ETHTOOL_COALESCE_USE_ADAPTIVE_RX |
 				     ETHTOOL_COALESCE_USE_CQE,
+	.supported_ring_params	= ETHTOOL_RING_USE_TCP_DATA_SPLIT,
 	.get_link_ksettings	= bnxt_get_link_ksettings,
 	.set_link_ksettings	= bnxt_set_link_ksettings,
 	.get_fec_stats		= bnxt_get_fec_stats,
drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c +0 -0
index f88b641533fc..1bfff7f29310 100644

drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c static int bnxt_xdp_set(struct bnxt *bp, struct bpf_prog *prog) · line 401

Quoted 7 lines
drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c +4 -0
@@ -395,6 +395,10 @@ static int bnxt_xdp_set(struct bnxt *bp, struct bpf_prog *prog)
 			    bp->dev->mtu, BNXT_MAX_PAGE_MODE_MTU);
 		return -EOPNOTSUPP;
 	}
+	if (prog && bp->flags & BNXT_FLAG_HDS) {
+		netdev_warn(dev, "XDP is disallowed when HDS is enabled.\n");
+		return -EOPNOTSUPP;
+	}

And this check should also live in the core, now that core has access to dev->ethtool->hds_config ? I think you can add this check to the core in the same patch as the chunk referred to above.

maintainer
#8 lore raw

Re: [PATCH net-next v6 3/9] bnxt_en: add support for tcp-data-split ethtool command

Quoted 8 lines · On Wed, 18 Dec 2024 18:25:47 -0800 Jakub Kicinski wrote:

drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c static int bnxt_xdp_set(struct bnxt *bp, struct bpf_prog *prog) · line 401

Quoted 4 lines
drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c +4 -0
+	if (prog && bp->flags & BNXT_FLAG_HDS) {
+		netdev_warn(dev, "XDP is disallowed when HDS is enabled.\n");
+		return -EOPNOTSUPP;
+	}  

And this check should also live in the core, now that core has access to dev->ethtool->hds_config ? I think you can add this check to the core in the same patch as the chunk referred to above.

Oh, you also already have this logic in patch 7?
So it just needs to be reordered in the series, and then the driver doesn't need to check?

author
#9 lore raw

Re: [PATCH net-next v6 3/9] bnxt_en: add support for tcp-data-split ethtool command

In reply to Jakub Kicinski
Quoted 8 lines · Jakub Kicinski

Review

Quoted 2 lines · On Wed, 18 Dec 2024 14:45:24 +0000 Taehee Yoo wrote:
(quoted diff) +2 -0
+     if (tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_DISABLED && hds_config_mod)
+             return -EOPNOTSUPP;

I think ethtool ops generally return -EINVAL when param not supported. EOPNOTSUPP means entire op is not supported (again, that's just how ethtool ops generally work, not a kernel-wide rule).

Thanks! I will use -EINVAL instead of EOPNOTSUPP.

Quoted 11 lines

drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c static int bnxt_set_ringparam(struct net_device *dev, · line 858

Quoted 3 lines
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c +2 -0
+     if (tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_ENABLED &&
+         hds_config_mod && BNXT_RX_PAGE_MODE(bp)) {

Looks like patch 4 adds this check in the core. I think adding the check in the core can be a separate patch. If you put it before this patch in the series this bnxt check can be removed?

I mean this chunk in the core:

Review

Quoted 7 lines
(quoted diff) +7 -0
+       hds_config_mod = old_hds_config != kernel_ringparam.tcp_data_split;
+       if (kernel_ringparam.tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_ENABLED &&
+           hds_config_mod && dev_xdp_sb_prog_count(dev)) {
+               NL_SET_ERR_MSG(info->extack,
+                              "tcp-data-split can not be enabled with single buffer XDP");
+               return -EINVAL;
+       }

Right, The core checks single buffer XDP.
But there was a review that bnxt_en driver doesn't support both single and multi buffer XDP if HDS is in use.
So, this is the reason why logic exists.

Quoted 2 lines

It's currently in the hds-thresh patch but really it's unrelated to the threshold..

Thanks, I will move this code to a HDS related patch, not hds-threshold, or create new patch for this.

Quoted 34 lines
Quoted 34 lines
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c +12 -0
+             NL_SET_ERR_MSG_MOD(extack, "tcp-data-split is disallowed when XDP is attached");
+             return -EOPNOTSUPP;
+     }
+
      if (netif_running(dev))
              bnxt_close_nic(bp, false, false);
 
+     if (hds_config_mod) {
+             if (tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_ENABLED)
+                     bp->flags |= BNXT_FLAG_HDS;
+             else if (tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_UNKNOWN)
+                     bp->flags &= ~BNXT_FLAG_HDS;
+     }
+
      bp->rx_ring_size = ering->rx_pending;
      bp->tx_ring_size = ering->tx_pending;
      bnxt_set_ring_params(bp);
@@ -5354,6 +5374,7 @@ const struct ethtool_ops bnxt_ethtool_ops = {
                                   ETHTOOL_COALESCE_STATS_BLOCK_USECS |
                                   ETHTOOL_COALESCE_USE_ADAPTIVE_RX |
                                   ETHTOOL_COALESCE_USE_CQE,
+     .supported_ring_params  = ETHTOOL_RING_USE_TCP_DATA_SPLIT,
      .get_link_ksettings     = bnxt_get_link_ksettings,
      .set_link_ksettings     = bnxt_set_link_ksettings,
      .get_fec_stats          = bnxt_get_fec_stats,
drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c +0 -0
index f88b641533fc..1bfff7f29310 100644
@@ -395,6 +395,10 @@ static int bnxt_xdp_set(struct bnxt *bp, struct bpf_prog *prog)
                          bp->dev->mtu, BNXT_MAX_PAGE_MODE_MTU);
              return -EOPNOTSUPP;
      }
Quoted 8 lines

drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c static int bnxt_xdp_set(struct bnxt *bp, struct bpf_prog *prog) · line 401

Quoted 4 lines
drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c +4 -0
+     if (prog && bp->flags & BNXT_FLAG_HDS) {
+             netdev_warn(dev, "XDP is disallowed when HDS is enabled.\n");
+             return -EOPNOTSUPP;
+     }

And this check should also live in the core, now that core has access to dev->ethtool->hds_config ? I think you can add this check to the core in the same patch as the chunk referred to above.

The bnxt_en disallows setting up both single and multi buffer XDP, but core checks only single buffer XDP. So, if multi buffer XDP is attaching to the bnxt_en driver when HDS is enabled, the core can't filter it.

Thanks a lot!
Taehee Yoo

maintainer
#10 lore raw

Re: [PATCH net-next v6 3/9] bnxt_en: add support for tcp-data-split ethtool command

Quoted 17 lines · On Thu, 19 Dec 2024 23:05:30 +0900 Taehee Yoo wrote:
Quoted 8 lines
Quoted 8 lines
drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c +0 -0
index f88b641533fc..1bfff7f29310 100644
@@ -395,6 +395,10 @@ static int bnxt_xdp_set(struct bnxt *bp, struct bpf_prog *prog)
                          bp->dev->mtu, BNXT_MAX_PAGE_MODE_MTU);
              return -EOPNOTSUPP;
      }
Quoted 8 lines

drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c static int bnxt_xdp_set(struct bnxt *bp, struct bpf_prog *prog) · line 401

Quoted 4 lines
drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c +4 -0
+     if (prog && bp->flags & BNXT_FLAG_HDS) {
+             netdev_warn(dev, "XDP is disallowed when HDS is enabled.\n");
+             return -EOPNOTSUPP;
+     }  

And this check should also live in the core, now that core has access to dev->ethtool->hds_config ? I think you can add this check to the core in the same patch as the chunk referred to above.

Quoted 3 lines

The bnxt_en disallows setting up both single and multi buffer XDP, but core checks only single buffer XDP. So, if multi buffer XDP is attaching to the bnxt_en driver when HDS is enabled, the core can't filter it.

Hm. Did you find this in the code, or did Broadcom folks suggest it? AFAICT bnxt supports multi-buf XDP. Is there something in the code that special-cases aggregation but doesn't work for pure HDS?

author
#11 lore raw

Re: [PATCH net-next v6 3/9] bnxt_en: add support for tcp-data-split ethtool command

Quoted 19 lines · Jakub Kicinski
Quoted 17 lines · On Thu, 19 Dec 2024 23:05:30 +0900 Taehee Yoo wrote:
Quoted 16 lines

drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c static int bnxt_xdp_set(struct bnxt *bp, struct bpf_prog *prog) · line 401

Quoted 12 lines
drivers/net/ethernet/broadcom/bnxt/bnxt_xdp.c +4 -0
index f88b641533fc..1bfff7f29310 100644
@@ -395,6 +395,10 @@ static int bnxt_xdp_set(struct bnxt *bp, struct bpf_prog *prog)
                          bp->dev->mtu, BNXT_MAX_PAGE_MODE_MTU);
              return -EOPNOTSUPP;
      }
+     if (prog && bp->flags & BNXT_FLAG_HDS) {
+             netdev_warn(dev, "XDP is disallowed when HDS is enabled.\n");
+             return -EOPNOTSUPP;
+     }

And this check should also live in the core, now that core has access to dev->ethtool->hds_config ? I think you can add this check to the core in the same patch as the chunk referred to above.

Quoted 7 lines
Quoted 3 lines

The bnxt_en disallows setting up both single and multi buffer XDP, but core checks only single buffer XDP. So, if multi buffer XDP is attaching to the bnxt_en driver when HDS is enabled, the core can't filter it.

Hm. Did you find this in the code, or did Broadcom folks suggest it? AFAICT bnxt supports multi-buf XDP. Is there something in the code that special-cases aggregation but doesn't work for pure HDS?

There were some comments about HDS with XDP in the following thread.
https://lore.kernel.org/netdev/[email protected]/T/
I may misunderstand reviews from Broadcom folks.

maintainer
#12 lore raw

Re: [PATCH net-next v6 3/9] bnxt_en: add support for tcp-data-split ethtool command

Quoted 11 lines · On Fri, 20 Dec 2024 00:14:01 +0900 Taehee Yoo wrote:
Quoted 7 lines
Quoted 3 lines

The bnxt_en disallows setting up both single and multi buffer XDP, but core checks only single buffer XDP. So, if multi buffer XDP is attaching to the bnxt_en driver when HDS is enabled, the core can't filter it.

Hm. Did you find this in the code, or did Broadcom folks suggest it? AFAICT bnxt supports multi-buf XDP. Is there something in the code that special-cases aggregation but doesn't work for pure HDS?

There were some comments about HDS with XDP in the following thread.
https://lore.kernel.org/netdev/[email protected]/T/
I may misunderstand reviews from Broadcom folks.

I see it now in bnxt_set_rx_skb_mode. I guess with high MTU the device splits in some "dumb" way, at a fixed offset.. You're right, we have to keep the check in the driver, at least for now.

#13 lore raw

Re: [PATCH net-next v6 3/9] bnxt_en: add support for tcp-data-split ethtool command

Quoted 9 lines · Jakub Kicinski
Quoted 8 lines · On Fri, 20 Dec 2024 00:14:01 +0900 Taehee Yoo wrote:
Quoted 7 lines
Quoted 3 lines

The bnxt_en disallows setting up both single and multi buffer XDP, but core checks only single buffer XDP. So, if multi buffer XDP is attaching to the bnxt_en driver when HDS is enabled, the core can't filter it.

Hm. Did you find this in the code, or did Broadcom folks suggest it? AFAICT bnxt supports multi-buf XDP. Is there something in the code that special-cases aggregation but doesn't work for pure HDS?

Quoted 8 lines
Quoted 3 lines

There were some comments about HDS with XDP in the following thread.
https://lore.kernel.org/netdev/[email protected]/T/
I may misunderstand reviews from Broadcom folks.

I see it now in bnxt_set_rx_skb_mode. I guess with high MTU the device splits in some "dumb" way, at a fixed offset.. You're right, we have to keep the check in the driver, at least for now.

The mutlti-buffer implementation followed what was done at the time in other drivers. Is the 'dumb way' you mention this check?

4717 if (dev->mtu > BNXT_MAX_PAGE_MODE_MTU) {
4718 bp->flags |= BNXT_FLAG_JUMBO;
4719 bp->rx_skb_func = bnxt_rx_multi_page_skb;
4720 } else {
4721 bp->flags |= BNXT_FLAG_NO_AGG_RINGS;
4722 bp->rx_skb_func = bnxt_rx_page_skb;
4723 }

maintainer
#14 lore raw

Re: [PATCH net-next v6 3/9] bnxt_en: add support for tcp-data-split ethtool command

Quoted 8 lines · On Thu, 19 Dec 2024 14:33:44 -0500 Andy Gospodarek wrote:
Quoted 4 lines

I see it now in bnxt_set_rx_skb_mode. I guess with high MTU the device splits in some "dumb" way, at a fixed offset.. You're right, we have to keep the check in the driver, at least for now.

The mutlti-buffer implementation followed what was done at the time in other drivers. Is the 'dumb way' you mention this check?

Quoted 7 lines

4717 if (dev->mtu > BNXT_MAX_PAGE_MODE_MTU) {
4718 bp->flags |= BNXT_FLAG_JUMBO;
4719 bp->rx_skb_func = bnxt_rx_multi_page_skb;
4720 } else {
4721 bp->flags |= BNXT_FLAG_NO_AGG_RINGS;
4722 bp->rx_skb_func = bnxt_rx_page_skb;
4723 }

Yes, that and my interpretation of the previous discussion let me to believe that the BNXT_FLAG_JUMBO does not enable header-data split. And speculating further I thought that perhaps the buffer split with jumbo > 4k is to fill first buffer completely, header+however much data fits.

I could have misread the previous conversation (perhaps Michael meant XDP SB / PAGE_MODE when he was referring to XDP limitations?)

Or maybe the HDS does happen with XDP MB but there is another limitation in the code?

I'm not sure. At this stage we just need to know if the check in the driver is really needed or XDP MB + HDS are fine, and we can remove the driver check, as core already prevents XDP SB + HDS. Could you clarify?

maintainer
#15 lore raw

Re: [PATCH net-next v6 3/9] bnxt_en: add support for tcp-data-split ethtool command

Quoted 18 lines · Jakub Kicinski
Quoted 8 lines · On Thu, 19 Dec 2024 14:33:44 -0500 Andy Gospodarek wrote:
Quoted 4 lines

I see it now in bnxt_set_rx_skb_mode. I guess with high MTU the device splits in some "dumb" way, at a fixed offset.. You're right, we have to keep the check in the driver, at least for now.

The mutlti-buffer implementation followed what was done at the time in other drivers. Is the 'dumb way' you mention this check?

Quoted 7 lines

4717 if (dev->mtu > BNXT_MAX_PAGE_MODE_MTU) {
4718 bp->flags |= BNXT_FLAG_JUMBO;
4719 bp->rx_skb_func = bnxt_rx_multi_page_skb;
4720 } else {
4721 bp->flags |= BNXT_FLAG_NO_AGG_RINGS;
4722 bp->rx_skb_func = bnxt_rx_page_skb;
4723 }

Quoted 8 lines

Yes, that and my interpretation of the previous discussion let me to believe that the BNXT_FLAG_JUMBO does not enable header-data split. And speculating further I thought that perhaps the buffer split with jumbo > 4k is to fill first buffer completely, header+however much data fits.

I could have misread the previous conversation (perhaps Michael meant XDP SB / PAGE_MODE when he was referring to XDP limitations?)

To clarify, my review comment applied to XDP SB and MB modes. Andy's MB implementation from 2022 disables HWGRO/LRO and HDS in XDP MB mode. My comment was to preserve this implementation.

Quoted 3 lines

Or maybe the HDS does happen with XDP MB but there is another limitation in the code?

HW doesn't know whether we're in XDP mode or not and can definitely do HDS. But again, HDS is disabled currently in any XDP mode. Andy will respond to discuss this further. Long term, we may be able to enable HDS in XDP MB mode, but for now I think we should disable it just to keep it unchanged.

maintainer
#16 lore raw

Re: [PATCH net-next v6 3/9] bnxt_en: add support for tcp-data-split ethtool command

Quoted 8 lines · On Thu, 19 Dec 2024 15:41:17 -0800 Michael Chan wrote:
Quoted 2 lines

Or maybe the HDS does happen with XDP MB but there is another limitation in the code?

HW doesn't know whether we're in XDP mode or not and can definitely do HDS. But again, HDS is disabled currently in any XDP mode. Andy will respond to discuss this further. Long term, we may be able to enable HDS in XDP MB mode, but for now I think we should disable it just to keep it unchanged.

SGTM, this series accomplishes enough things already :)

author
#17 lore raw

PATCH v6 4/9 net: ethtool: add support for configuring hds-thresh

In reply to Taehee Yoo

The hds-thresh option configures the threshold value of
the header-data-split.
If a received packet size is larger than this threshold value, a packet will be split into header and payload.
The header indicates TCP and UDP header, but it depends on driver spec. The bnxt_en driver supports HDS(Header-Data-Split) configuration at FW level, affecting TCP and UDP too.
So, If hds-thresh is set, it affects UDP and TCP packets.

Example:

   # ethtool -G <interface name> hds-thresh <value>
   # ethtool -G enp14s0f0np0 tcp-data-split on hds-thresh 256
   # ethtool -g enp14s0f0np0
   Ring parameters for enp14s0f0np0:
   Pre-set maximums:
   ...
   HDS thresh:  1023
   Current hardware settings:
   ...
   TCP data split:         on
   HDS thresh:  256

The default/min/max values are not defined in the ethtool so the drivers should define themself.
The 0 value means that all TCP/UDP packets' header and payload will be split.

---

v6:
- Update ethtool_netlink_generated.h
- Use "HDS" instead of "HEADER_DATA_SPLIT"
- Add Test tag from Andy.

v5:
- No changes.

v4:
- Fix 80 charactor wrap.
- Rename from tcp-data-split-thresh to header-data-split-thresh
- Add description about overhead of HDS.
- Add ETHTOOL_RING_USE_HDS_THRS flag.
- Add dev_xdp_sb_prog_count() helper.
- Add Test tag from Stanislav.

v3:
- Fix documentation and ynl
- Update error messages
- Validate configuration of tcp-data-split and tcp-data-split-thresh

v2:
- Patch added.

 Documentation/netlink/specs/ethtool.yaml      |  8 ++++
 Documentation/networking/ethtool-netlink.rst  | 10 +++++
 include/linux/ethtool.h                       |  6 +++
 include/linux/netdevice.h                     |  1 +
 .../uapi/linux/ethtool_netlink_generated.h    |  2 +
 net/core/dev.c                                | 13 ++++++
 net/ethtool/netlink.h                         |  2 +-
 net/ethtool/rings.c                           | 40 +++++++++++++++++--
 8 files changed, 78 insertions(+), 4 deletions(-)
Documentation/netlink/specs/ethtool.yaml +8 -0
index 60f85fbf4156..66be04013048 100644
@@ -332,6 +332,12 @@ attribute-sets:
       -
         name: tx-push-buf-len-max
         type: u32
+      -
+        name: hds-thresh
+        type: u32
+      -
+        name: hds-thresh-max
+        type: u32
 
   -
     name: mm-stat
@@ -1777,6 +1783,8 @@ operations:
             - rx-push
             - tx-push-buf-len
             - tx-push-buf-len-max
+            - hds-thresh
+            - hds-thresh-max
       dump: *ring-get-op
     -
       name: rings-set
Documentation/networking/ethtool-netlink.rst +10 -0
index a7ba6368a4d5..ef1d1750f960 100644
@@ -899,6 +899,10 @@ Kernel response contents:
   ``ETHTOOL_A_RINGS_RX_PUSH``               u8      flag of RX Push mode
   ``ETHTOOL_A_RINGS_TX_PUSH_BUF_LEN``       u32     size of TX push buffer
   ``ETHTOOL_A_RINGS_TX_PUSH_BUF_LEN_MAX``   u32     max size of TX push buffer
+  ``ETHTOOL_A_RINGS_HDS_THRESH``            u32     threshold of
+                                                    header / data split
+  ``ETHTOOL_A_RINGS_HDS_THRESH_MAX``        u32     max threshold of
+                                                    header / data split
   =======================================   ======  ===========================
 
 ``ETHTOOL_A_RINGS_TCP_DATA_SPLIT`` indicates whether the device is usable with
@@ -941,10 +945,12 @@ Request contents:
   ``ETHTOOL_A_RINGS_RX_JUMBO``          u32     size of RX jumbo ring
   ``ETHTOOL_A_RINGS_TX``                u32     size of TX ring
   ``ETHTOOL_A_RINGS_RX_BUF_LEN``        u32     size of buffers on the ring
+  ``ETHTOOL_A_RINGS_TCP_DATA_SPLIT``    u8      TCP header / data split
   ``ETHTOOL_A_RINGS_CQE_SIZE``          u32     Size of TX/RX CQE
   ``ETHTOOL_A_RINGS_TX_PUSH``           u8      flag of TX Push mode
   ``ETHTOOL_A_RINGS_RX_PUSH``           u8      flag of RX Push mode
   ``ETHTOOL_A_RINGS_TX_PUSH_BUF_LEN``   u32     size of TX push buffer
+  ``ETHTOOL_A_RINGS_HDS_THRESH``        u32     threshold of header / data split
   ====================================  ======  ===========================
 
 Kernel checks that requested ring sizes do not exceed limits reported by
@@ -961,6 +967,10 @@ A bigger CQE can have more receive buffer pointers, and in turn the NIC can
 transfer a bigger frame from wire. Based on the NIC hardware, the overall
 completion queue size can be adjusted in the driver if CQE size is modified.
 
+``ETHTOOL_A_RINGS_HDS_THRESH`` specifies the threshold value of
+header / data split feature. If a received packet size is larger than this
+threshold value, header and data will be split.
+
 CHANNELS_GET
 ============
 
include/linux/ethtool.h +6 -0
index 4e451084d58a..4f407ce9eed1 100644
@@ -78,6 +78,8 @@ enum {
  * @cqe_size: Size of TX/RX completion queue event
  * @tx_push_buf_len: Size of TX push buffer
  * @tx_push_buf_max_len: Maximum allowed size of TX push buffer
+ * @hds_thresh: Threshold value of header-data-split-thresh
+ * @hds_thresh_max: Maximum allowed threshold of header-data-split-thresh
  */
 struct kernel_ethtool_ringparam {
 	u32	rx_buf_len;
@@ -87,6 +89,8 @@ struct kernel_ethtool_ringparam {
 	u32	cqe_size;
 	u32	tx_push_buf_len;
 	u32	tx_push_buf_max_len;
+	u32	hds_thresh;
+	u32	hds_thresh_max;
 };
 
 /**
@@ -97,6 +101,7 @@ struct kernel_ethtool_ringparam {
  * @ETHTOOL_RING_USE_RX_PUSH: capture for setting rx_push
  * @ETHTOOL_RING_USE_TX_PUSH_BUF_LEN: capture for setting tx_push_buf_len
  * @ETHTOOL_RING_USE_TCP_DATA_SPLIT: capture for setting tcp_data_split
+ * @ETHTOOL_RING_USE_HDS_THRS: capture for setting header-data-split-thresh
  */
 enum ethtool_supported_ring_param {
 	ETHTOOL_RING_USE_RX_BUF_LEN		= BIT(0),
@@ -105,6 +110,7 @@ enum ethtool_supported_ring_param {
 	ETHTOOL_RING_USE_RX_PUSH		= BIT(3),
 	ETHTOOL_RING_USE_TX_PUSH_BUF_LEN	= BIT(4),
 	ETHTOOL_RING_USE_TCP_DATA_SPLIT		= BIT(5),
+	ETHTOOL_RING_USE_HDS_THRS		= BIT(6),
 };
 
 #define __ETH_RSS_HASH_BIT(bit)	((u32)1 << (bit))
include/linux/netdevice.h +1 -0
index 2593019ad5b1..b18f249826c5 100644
@@ -4083,6 +4083,7 @@ struct sk_buff *dev_hard_start_xmit(struct sk_buff *skb, struct net_device *dev,
 
 int bpf_xdp_link_attach(const union bpf_attr *attr, struct bpf_prog *prog);
 u8 dev_xdp_prog_count(struct net_device *dev);
+u8 dev_xdp_sb_prog_count(struct net_device *dev);
 int dev_xdp_propagate(struct net_device *dev, struct netdev_bpf *bpf);
 u32 dev_xdp_prog_id(struct net_device *dev, enum bpf_xdp_mode mode);
 
include/uapi/linux/ethtool_netlink_generated.h +2 -0
index 43993a2d68e5..2e17ff348f89 100644
@@ -155,6 +155,8 @@ enum {
 	ETHTOOL_A_RINGS_RX_PUSH,
 	ETHTOOL_A_RINGS_TX_PUSH_BUF_LEN,
 	ETHTOOL_A_RINGS_TX_PUSH_BUF_LEN_MAX,
+	ETHTOOL_A_RINGS_HDS_THRESH,
+	ETHTOOL_A_RINGS_HDS_THRESH_MAX,
 
 	__ETHTOOL_A_RINGS_CNT,
 	ETHTOOL_A_RINGS_MAX = (__ETHTOOL_A_RINGS_CNT - 1)
net/core/dev.c +13 -0
index c7f3dea3e0eb..6a68db95de76 100644
@@ -9480,6 +9480,19 @@ u8 dev_xdp_prog_count(struct net_device *dev)
 }
 EXPORT_SYMBOL_GPL(dev_xdp_prog_count);
 
+u8 dev_xdp_sb_prog_count(struct net_device *dev)
+{
+	u8 count = 0;
+	int i;
+
+	for (i = 0; i < __MAX_XDP_MODE; i++)
+		if (dev->xdp_state[i].prog &&
+		    !dev->xdp_state[i].prog->aux->xdp_has_frags)
+			count++;
+	return count;
+}
+EXPORT_SYMBOL_GPL(dev_xdp_sb_prog_count);
+
 int dev_xdp_propagate(struct net_device *dev, struct netdev_bpf *bpf)
 {
 	if (!dev->netdev_ops->ndo_bpf)
net/ethtool/netlink.h +1 -1
index 0a09298fff92..c523b763efa3 100644
@@ -456,7 +456,7 @@ extern const struct nla_policy ethnl_features_set_policy[ETHTOOL_A_FEATURES_WANT
 extern const struct nla_policy ethnl_privflags_get_policy[ETHTOOL_A_PRIVFLAGS_HEADER + 1];
 extern const struct nla_policy ethnl_privflags_set_policy[ETHTOOL_A_PRIVFLAGS_FLAGS + 1];
 extern const struct nla_policy ethnl_rings_get_policy[ETHTOOL_A_RINGS_HEADER + 1];
-extern const struct nla_policy ethnl_rings_set_policy[ETHTOOL_A_RINGS_TX_PUSH_BUF_LEN_MAX + 1];
+extern const struct nla_policy ethnl_rings_set_policy[ETHTOOL_A_RINGS_HDS_THRESH_MAX + 1];
 extern const struct nla_policy ethnl_channels_get_policy[ETHTOOL_A_CHANNELS_HEADER + 1];
 extern const struct nla_policy ethnl_channels_set_policy[ETHTOOL_A_CHANNELS_COMBINED_COUNT + 1];
 extern const struct nla_policy ethnl_coalesce_get_policy[ETHTOOL_A_COALESCE_HEADER + 1];
net/ethtool/rings.c +37 -3
index 2e8239a76234..c0cb9b2c6616 100644
@@ -61,7 +61,9 @@ static int rings_reply_size(const struct ethnl_req_info *req_base,
 	       nla_total_size(sizeof(u8))  +	/* _RINGS_TX_PUSH */
 	       nla_total_size(sizeof(u8))) +	/* _RINGS_RX_PUSH */
 	       nla_total_size(sizeof(u32)) +	/* _RINGS_TX_PUSH_BUF_LEN */
-	       nla_total_size(sizeof(u32));	/* _RINGS_TX_PUSH_BUF_LEN_MAX */
+	       nla_total_size(sizeof(u32)) +	/* _RINGS_TX_PUSH_BUF_LEN_MAX */
+	       nla_total_size(sizeof(u32)) +	/* _RINGS_HDS_THRESH */
+	       nla_total_size(sizeof(u32));	/* _RINGS_HDS_THRESH_MAX*/
 }
 
 static int rings_fill_reply(struct sk_buff *skb,
@@ -108,7 +110,12 @@ static int rings_fill_reply(struct sk_buff *skb,
 	     (nla_put_u32(skb, ETHTOOL_A_RINGS_TX_PUSH_BUF_LEN_MAX,
 			  kr->tx_push_buf_max_len) ||
 	      nla_put_u32(skb, ETHTOOL_A_RINGS_TX_PUSH_BUF_LEN,
-			  kr->tx_push_buf_len))))
+			  kr->tx_push_buf_len))) ||
+	    ((supported_ring_params & ETHTOOL_RING_USE_HDS_THRS) &&
+	     (nla_put_u32(skb, ETHTOOL_A_RINGS_HDS_THRESH,
+			  kr->hds_thresh) ||
+	      nla_put_u32(skb, ETHTOOL_A_RINGS_HDS_THRESH_MAX,
+			  kr->hds_thresh_max))))
 		return -EMSGSIZE;
 
 	return 0;
@@ -130,6 +137,7 @@ const struct nla_policy ethnl_rings_set_policy[] = {
 	[ETHTOOL_A_RINGS_TX_PUSH]		= NLA_POLICY_MAX(NLA_U8, 1),
 	[ETHTOOL_A_RINGS_RX_PUSH]		= NLA_POLICY_MAX(NLA_U8, 1),
 	[ETHTOOL_A_RINGS_TX_PUSH_BUF_LEN]	= { .type = NLA_U32 },
+	[ETHTOOL_A_RINGS_HDS_THRESH]		= { .type = NLA_U32 },
 };
 
 static int
@@ -155,6 +163,14 @@ ethnl_set_rings_validate(struct ethnl_req_info *req_info,
 		return -EOPNOTSUPP;
 	}
 
+	if (tb[ETHTOOL_A_RINGS_HDS_THRESH] &&
+	    !(ops->supported_ring_params & ETHTOOL_RING_USE_HDS_THRS)) {
+		NL_SET_ERR_MSG_ATTR(info->extack,
+				    tb[ETHTOOL_A_RINGS_HDS_THRESH],
+				    "setting hds-thresh is not supported");
+		return -EOPNOTSUPP;
+	}
+
 	if (tb[ETHTOOL_A_RINGS_CQE_SIZE] &&
 	    !(ops->supported_ring_params & ETHTOOL_RING_USE_CQE_SIZE)) {
 		NL_SET_ERR_MSG_ATTR(info->extack,
@@ -196,14 +212,16 @@ ethnl_set_rings(struct ethnl_req_info *req_info, struct genl_info *info)
 	struct kernel_ethtool_ringparam kernel_ringparam = {};
 	struct ethtool_ringparam ringparam = {};
 	struct net_device *dev = req_info->dev;
+	u8 old_hds_config, hds_config_mod;
 	struct nlattr **tb = info->attrs;
 	const struct nlattr *err_attr;
 	bool mod = false;
 	int ret;
 
+	old_hds_config = dev->ethtool->hds_config;
 	dev->ethtool_ops->get_ringparam(dev, &ringparam,
 					&kernel_ringparam, info->extack);
-	kernel_ringparam.tcp_data_split = dev->ethtool->hds_config;
+	kernel_ringparam.tcp_data_split = old_hds_config;
 
 	ethnl_update_u32(&ringparam.rx_pending, tb[ETHTOOL_A_RINGS_RX], &mod);
 	ethnl_update_u32(&ringparam.rx_mini_pending,
@@ -223,9 +241,25 @@ ethnl_set_rings(struct ethnl_req_info *req_info, struct genl_info *info)
 			tb[ETHTOOL_A_RINGS_RX_PUSH], &mod);
 	ethnl_update_u32(&kernel_ringparam.tx_push_buf_len,
 			 tb[ETHTOOL_A_RINGS_TX_PUSH_BUF_LEN], &mod);
+	ethnl_update_u32(&kernel_ringparam.hds_thresh,
+			 tb[ETHTOOL_A_RINGS_HDS_THRESH], &mod);
 	if (!mod)
 		return 0;
 
+	hds_config_mod = old_hds_config != kernel_ringparam.tcp_data_split;
+	if (kernel_ringparam.tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_ENABLED &&
+	    hds_config_mod && dev_xdp_sb_prog_count(dev)) {
+		NL_SET_ERR_MSG(info->extack,
+			       "tcp-data-split can not be enabled with single buffer XDP");
+		return -EINVAL;
+	}
+
+	if (kernel_ringparam.hds_thresh > kernel_ringparam.hds_thresh_max) {
+		NL_SET_BAD_ATTR(info->extack,
+				tb[ETHTOOL_A_RINGS_HDS_THRESH_MAX]);
+		return -ERANGE;
+	}
+
 	/* ensure new ring parameters are within limits */
 	if (ringparam.rx_pending > ringparam.rx_max_pending)
 		err_attr = tb[ETHTOOL_A_RINGS_RX];
Signature · 1 line
2.34.1
maintainer
#18 lore raw

Re: [PATCH net-next v6 4/9] net: ethtool: add support for configuring hds-thresh

include/linux/ethtool.h enum { · line 82

Quoted 10 lines · On Wed, 18 Dec 2024 14:45:25 +0000 Taehee Yoo wrote:
include/linux/ethtool.h +2 -0
index 4e451084d58a..4f407ce9eed1 100644
@@ -78,6 +78,8 @@ enum {
  * @cqe_size: Size of TX/RX completion queue event
  * @tx_push_buf_len: Size of TX push buffer
  * @tx_push_buf_max_len: Maximum allowed size of TX push buffer
+ * @hds_thresh: Threshold value of header-data-split-thresh
+ * @hds_thresh_max: Maximum allowed threshold of header-data-split-thresh

nit: s/allowed/supported/

include/linux/ethtool.h enum {

Quoted 12 lines
include/linux/ethtool.h +12 -0
+u8 dev_xdp_sb_prog_count(struct net_device *dev)
+{
+	u8 count = 0;
+	int i;
+
+	for (i = 0; i < __MAX_XDP_MODE; i++)
+		if (dev->xdp_state[i].prog &&
+		    !dev->xdp_state[i].prog->aux->xdp_has_frags)
+			count++;
+	return count;
+}
+EXPORT_SYMBOL_GPL(dev_xdp_sb_prog_count);

No need to export this, AFAICT, none of the callers can be built as a module.

include/linux/ethtool.h

Quoted 1 line
include/linux/ethtool.h +1 -0
+	hds_config_mod = old_hds_config != kernel_ringparam.tcp_data_split;

Does it really matter if we modified the HDS setting for the XDP check? Whether it was already set or the current config is asking for it to be set having XDP SB and HDS is invalid, we can return an error.

include/linux/ethtool.h

Quoted 3 lines
include/linux/ethtool.h +3 -0
+	if (kernel_ringparam.tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_ENABLED &&
+	    hds_config_mod && dev_xdp_sb_prog_count(dev)) {
+		NL_SET_ERR_MSG(info->extack,
		NL_SET_ERR_MSG_ATTR(info->extack,
				    tb[ETHTOOL_A_RINGS_TCP_DATA_SPLIT],
				    ...

include/linux/ethtool.h

Quoted 9 lines
include/linux/ethtool.h +9 -0
+			       "tcp-data-split can not be enabled with single buffer XDP");
+		return -EINVAL;
+	}
+
+	if (kernel_ringparam.hds_thresh > kernel_ringparam.hds_thresh_max) {
+		NL_SET_BAD_ATTR(info->extack,
+				tb[ETHTOOL_A_RINGS_HDS_THRESH_MAX]);
+		return -ERANGE;
+	}

Can this condition not be handled by the big if "ladder" below? I mean like this:

@@ -282,6 +276,8 @@ ethnl_set_rings(struct ethnl_req_info *req_info, struct genl_info *info)

                err_attr = tb[ETHTOOL_A_RINGS_RX_JUMBO];
        else if (ringparam.tx_pending > ringparam.tx_max_pending)
                err_attr = tb[ETHTOOL_A_RINGS_TX];
+       else if (kernel_ringparam.hds_thresh > kernel_ringparam.hds_thresh_max)
+               err_attr = tb[ETHTOOL_A_RINGS_HDS_THRESH_MAX];
        else
                err_attr = NULL;
        if (err_attr) {
Quoted 3 lines
include/linux/ethtool.h +0 -0
 	/* ensure new ring parameters are within limits */
 	if (ringparam.rx_pending > ringparam.rx_max_pending)
 		err_attr = tb[ETHTOOL_A_RINGS_RX];
author
#19 lore raw

Re: [PATCH net-next v6 4/9] net: ethtool: add support for configuring hds-thresh

Quoted 14 lines · Jakub Kicinski

include/linux/ethtool.h enum { · line 82

Quoted 10 lines · On Wed, 18 Dec 2024 14:45:25 +0000 Taehee Yoo wrote:
include/linux/ethtool.h +2 -0
index 4e451084d58a..4f407ce9eed1 100644
@@ -78,6 +78,8 @@ enum {
  * @cqe_size: Size of TX/RX completion queue event
  * @tx_push_buf_len: Size of TX push buffer
  * @tx_push_buf_max_len: Maximum allowed size of TX push buffer
+ * @hds_thresh: Threshold value of header-data-split-thresh
+ * @hds_thresh_max: Maximum allowed threshold of header-data-split-thresh

nit: s/allowed/supported/

Thanks, I will change it.

Quoted 16 lines

include/linux/ethtool.h enum {

Quoted 13 lines
include/linux/ethtool.h +12 -0
+u8 dev_xdp_sb_prog_count(struct net_device *dev)
+{
+     u8 count = 0;
+     int i;
+
+     for (i = 0; i < __MAX_XDP_MODE; i++)
+             if (dev->xdp_state[i].prog &&
+                 !dev->xdp_state[i].prog->aux->xdp_has_frags)
+                     count++;
+     return count;
+}
+EXPORT_SYMBOL_GPL(dev_xdp_sb_prog_count);

No need to export this, AFAICT, none of the callers can be built as a module.

Okay, I will not export this function.

Quoted 6 lines
Quoted 2 lines

+ hds_config_mod = old_hds_config != kernel_ringparam.tcp_data_split;

Does it really matter if we modified the HDS setting for the XDP check? Whether it was already set or the current config is asking for it to be set having XDP SB and HDS is invalid, we can return an error.

Right, it doesn't need to check modification.
I will remove it.

Quoted 6 lines

include/linux/ethtool.h

Quoted 4 lines
include/linux/ethtool.h +3 -0
+     if (kernel_ringparam.tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_ENABLED &&
+         hds_config_mod && dev_xdp_sb_prog_count(dev)) {
+             NL_SET_ERR_MSG(info->extack,
                NL_SET_ERR_MSG_ATTR(info->extack,

Thanks for it too, I will use it.

Quoted 13 lines
                                    tb[ETHTOOL_A_RINGS_TCP_DATA_SPLIT],
                                    ...

include/linux/ethtool.h

Quoted 9 lines
include/linux/ethtool.h +9 -0
+                            "tcp-data-split can not be enabled with single buffer XDP");
+             return -EINVAL;
+     }
+
+     if (kernel_ringparam.hds_thresh > kernel_ringparam.hds_thresh_max) {
+             NL_SET_BAD_ATTR(info->extack,
+                             tb[ETHTOOL_A_RINGS_HDS_THRESH_MAX]);
+             return -ERANGE;
+     }
Quoted 2 lines

Can this condition not be handled by the big if "ladder" below? I mean like this:

Thanks for that, I will try to apply it!

Quoted 11 lines
(quoted diff) +2 -0
@@ -282,6 +276,8 @@ ethnl_set_rings(struct ethnl_req_info *req_info, struct genl_info *info)
                err_attr = tb[ETHTOOL_A_RINGS_RX_JUMBO];
        else if (ringparam.tx_pending > ringparam.tx_max_pending)
                err_attr = tb[ETHTOOL_A_RINGS_TX];
+       else if (kernel_ringparam.hds_thresh > kernel_ringparam.hds_thresh_max)
+               err_attr = tb[ETHTOOL_A_RINGS_HDS_THRESH_MAX];
        else
                err_attr = NULL;
        if (err_attr) {
Quoted 3 lines
Quoted 3 lines
      /* ensure new ring parameters are within limits */
      if (ringparam.rx_pending > ringparam.rx_max_pending)
              err_attr = tb[ETHTOOL_A_RINGS_RX];

Thanks a lot!
Taehee Yoo

author
#20 lore raw

PATCH v6 5/9 bnxt_en: add support for hds-thresh ethtool command

In reply to Taehee Yoo

The bnxt_en driver has configured the hds_threshold value automatically when TPA is enabled based on the rx-copybreak default value. Now the hds-thresh ethtool command is added, so it adds an implementation of hds-thresh option.

Configuration of the hds-thresh is applied only when the tcp-data-split is enabled. The default value of hds-thresh is 256, which is the default value of rx-copybreak, which used to be the hds_thresh value.

The maximum hds-thresh is 1023.

# Example:

   # ethtool -G enp14s0f0np0 tcp-data-split on hds-thresh 256
   # ethtool -g enp14s0f0np0
   Ring parameters for enp14s0f0np0:
   Pre-set maximums:
   ...
   HDS thresh:  1023
   Current hardware settings:
   ...
   TCP data split:         on
   HDS thresh:  256

---

v6:
- HDS_MAX is changed to 1023.
- Add Test tag from Andy.

v5:
- No changes.

v4:
- Reduce hole in struct bnxt.
- Add ETHTOOL_RING_USE_HDS_THRS to indicate bnxt_en driver support header-data-split-thresh option.
- Add Test tag from Stanislav.

v3:
- Drop validation logic tcp-data-split and tcp-data-split-thresh.

v2:
- Patch added.

 drivers/net/ethernet/broadcom/bnxt/bnxt.c         | 3 ++-
 drivers/net/ethernet/broadcom/bnxt/bnxt.h         | 2 ++
 drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c | 7 ++++++-
 3 files changed, 10 insertions(+), 2 deletions(-)
drivers/net/ethernet/broadcom/bnxt/bnxt.c +2 -1
index 42ffaa88ae4e..5b16b2ef7739 100644
@@ -4603,6 +4603,7 @@ void bnxt_set_tpa_flags(struct bnxt *bp)
 static void bnxt_init_ring_params(struct bnxt *bp)
 {
 	bp->rx_copybreak = BNXT_DEFAULT_RX_COPYBREAK;
+	bp->hds_threshold = BNXT_DEFAULT_RX_COPYBREAK;
 }
 
 /* bp->rx_ring_size, bp->tx_ring_size, dev->mtu, BNXT_FLAG_{G|L}RO flags must
@@ -6578,7 +6579,7 @@ static int bnxt_hwrm_vnic_set_hds(struct bnxt *bp, struct bnxt_vnic_info *vnic)
 					  VNIC_PLCMODES_CFG_REQ_FLAGS_HDS_IPV6);
 		req->enables |=
 			cpu_to_le32(VNIC_PLCMODES_CFG_REQ_ENABLES_HDS_THRESHOLD_VALID);
-		req->hds_threshold = cpu_to_le16(bp->rx_copybreak);
+		req->hds_threshold = cpu_to_le16(bp->hds_threshold);
 	}
 	req->vnic_id = cpu_to_le32(vnic->fw_vnic_id);
 	return hwrm_req_send(bp, req);
drivers/net/ethernet/broadcom/bnxt/bnxt.h +2 -0
index 847dedf61a9e..8fc4d630ee21 100644
@@ -2404,6 +2404,8 @@ struct bnxt {
 	u8			q_ids[BNXT_MAX_QUEUE];
 	u8			max_q;
 	u8			num_tc;
+#define BNXT_HDS_THRESHOLD_MAX	1023
+	u16			hds_threshold;
 
 	unsigned int		current_interval;
 #define BNXT_TIMER_INTERVAL	HZ
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c +6 -1
index 25eb5931aea9..921e7e8333e8 100644
@@ -833,6 +833,9 @@ static void bnxt_get_ringparam(struct net_device *dev,
 	ering->rx_pending = bp->rx_ring_size;
 	ering->rx_jumbo_pending = bp->rx_agg_ring_size;
 	ering->tx_pending = bp->tx_ring_size;
+
+	kernel_ering->hds_thresh = bp->hds_threshold;
+	kernel_ering->hds_thresh_max = BNXT_HDS_THRESHOLD_MAX;
 }
 
 static int bnxt_set_ringparam(struct net_device *dev,
@@ -870,6 +873,7 @@ static int bnxt_set_ringparam(struct net_device *dev,
 			bp->flags &= ~BNXT_FLAG_HDS;
 	}
 
+	bp->hds_threshold = (u16)kernel_ering->hds_thresh;
 	bp->rx_ring_size = ering->rx_pending;
 	bp->tx_ring_size = ering->tx_pending;
 	bnxt_set_ring_params(bp);
@@ -5374,7 +5378,8 @@ const struct ethtool_ops bnxt_ethtool_ops = {
 				     ETHTOOL_COALESCE_STATS_BLOCK_USECS |
 				     ETHTOOL_COALESCE_USE_ADAPTIVE_RX |
 				     ETHTOOL_COALESCE_USE_CQE,
-	.supported_ring_params	= ETHTOOL_RING_USE_TCP_DATA_SPLIT,
+	.supported_ring_params	= ETHTOOL_RING_USE_TCP_DATA_SPLIT |
+				  ETHTOOL_RING_USE_HDS_THRS,
 	.get_link_ksettings	= bnxt_get_link_ksettings,
 	.set_link_ksettings	= bnxt_set_link_ksettings,
 	.get_fec_stats		= bnxt_get_fec_stats,
Signature · 1 line
2.34.1
maintainer
#21 lore raw

Re: [PATCH net-next v6 5/9] bnxt_en: add support for hds-thresh ethtool command

drivers/net/ethernet/broadcom/bnxt/bnxt.h struct bnxt { · line 2408

Quoted 2 lines · On Wed, 18 Dec 2024 14:45:26 +0000 Taehee Yoo wrote:
drivers/net/ethernet/broadcom/bnxt/bnxt.h +2 -0
+#define BNXT_HDS_THRESHOLD_MAX	1023
+	u16			hds_threshold;

How about we add hds_threshold to struct ethtool_netdev_state ? That way in patch 6 we don't have to call the driver to get it.

author
#22 lore raw

Re: [PATCH net-next v6 5/9] bnxt_en: add support for hds-thresh ethtool command

Quoted 7 lines · Jakub Kicinski

drivers/net/ethernet/broadcom/bnxt/bnxt.h struct bnxt { · line 2408

Quoted 2 lines · On Wed, 18 Dec 2024 14:45:26 +0000 Taehee Yoo wrote:
drivers/net/ethernet/broadcom/bnxt/bnxt.h +2 -0
+#define BNXT_HDS_THRESHOLD_MAX       1023
+     u16                     hds_threshold;

How about we add hds_threshold to struct ethtool_netdev_state ? That way in patch 6 we don't have to call the driver to get it.

I agree, it looks much better! I will change it.

Thanks a lot!
Taehee Yoo

author
#23 lore raw

PATCH v6 6/9 net: devmem: add ring parameter filtering

In reply to Taehee Yoo

If driver doesn't support ring parameter or tcp-data-split configuration is not sufficient, the devmem should not be set up.
Before setup the devmem, tcp-data-split should be ON and hds-thresh value should be 0.

---

v6:
- No changes.

v5:
- Add Review tag from Mina.

v4:
- Check condition before __netif_get_rx_queue().
- Separate condition check.
- Add Test tag from Stanislav.

v3:
- Patch added.

 net/core/devmem.c | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
net/core/devmem.c +19 -0
index 0b6ed7525b22..a29333af3ebd 100644
@@ -8,6 +8,8 @@
  */
 
 #include <linux/dma-buf.h>
+#include <linux/ethtool.h>
+#include <linux/ethtool_netlink.h>
 #include <linux/genalloc.h>
 #include <linux/mm.h>
 #include <linux/netdevice.h>
@@ -131,6 +133,8 @@ int net_devmem_bind_dmabuf_to_queue(struct net_device *dev, u32 rxq_idx,
 				    struct net_devmem_dmabuf_binding *binding,
 				    struct netlink_ext_ack *extack)
 {
+	struct kernel_ethtool_ringparam kernel_ringparam = {};
+	struct ethtool_ringparam ringparam = {};
 	struct netdev_rx_queue *rxq;
 	u32 xa_idx;
 	int err;
@@ -140,6 +144,21 @@ int net_devmem_bind_dmabuf_to_queue(struct net_device *dev, u32 rxq_idx,
 		return -ERANGE;
 	}
 
+	if (dev->ethtool->hds_config != ETHTOOL_TCP_DATA_SPLIT_ENABLED) {
+		NL_SET_ERR_MSG(extack, "tcp-data-split is disabled");
+		return -EINVAL;
+	}
+
+	if (!dev->ethtool_ops->get_ringparam)
+		return -EOPNOTSUPP;
+
+	dev->ethtool_ops->get_ringparam(dev, &ringparam, &kernel_ringparam,
+					extack);
+	if (kernel_ringparam.hds_thresh) {
+		NL_SET_ERR_MSG(extack, "hds-thresh is not zero");
+		return -EINVAL;
+	}
+
 	rxq = __netif_get_rx_queue(dev, rxq_idx);
 	if (rxq->mp_params.mp_priv) {
 		NL_SET_ERR_MSG(extack, "designated queue already memory provider bound");
Signature · 1 line
2.34.1
author
#24 lore raw

PATCH v6 7/9 net: ethtool: add ring parameter filtering

In reply to Taehee Yoo

While the devmem is running, the tcp-data-split and hds-thresh configuration should not be changed.
If user tries to change tcp-data-split and threshold value while the devmem is running, it fails and shows extack message.

---

v6:
- No changes.

v5:
- Change extack message.
- Add Review tag from Mina.

v4:
- Check condition before __netif_get_rx_queue().
- Separate condition check.
- Add Test tag from Stanislav.

v3:
- Patch added.

 net/ethtool/rings.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)
net/ethtool/rings.c +13 -0
index c0cb9b2c6616..284ca34a3b41 100644
@@ -260,6 +260,19 @@ ethnl_set_rings(struct ethnl_req_info *req_info, struct genl_info *info)
 		return -ERANGE;
 	}
 
+	if (dev_get_min_mp_channel_count(dev)) {
+		if (kernel_ringparam.tcp_data_split !=
+		    ETHTOOL_TCP_DATA_SPLIT_ENABLED) {
+			NL_SET_ERR_MSG(info->extack,
+				       "can't disable tcp-data-split while device has memory provider enabled");
+			return -EINVAL;
+		} else if (kernel_ringparam.hds_thresh) {
+			NL_SET_ERR_MSG(info->extack,
+				       "can't set non-zero hds_thresh while device is memory provider enabled");
+			return -EINVAL;
+		}
+	}
+
 	/* ensure new ring parameters are within limits */
 	if (ringparam.rx_pending > ringparam.rx_max_pending)
 		err_attr = tb[ETHTOOL_A_RINGS_RX];
Signature · 1 line
2.34.1
author
#25 lore raw

PATCH v6 8/9 net: disallow setup single buffer XDP when tcp-data-split is enabled.

In reply to Taehee Yoo

When a single buffer XDP is attached, NIC should guarantee only single page packets will be received.
tcp-data-split feature splits packets into header and payload. single buffer XDP can't handle it properly.
So attaching single buffer XDP should be disallowed when tcp-data-split is enabled.

---

v6:
- Patch added.

 net/core/dev.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
net/core/dev.c +16 -0
index 6a68db95de76..da4a34bfb675 100644
@@ -92,6 +92,7 @@
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
 #include <linux/ethtool.h>
+#include <linux/ethtool_netlink.h>
 #include <linux/skbuff.h>
 #include <linux/kthread.h>
 #include <linux/bpf.h>
@@ -9498,6 +9499,15 @@ int dev_xdp_propagate(struct net_device *dev, struct netdev_bpf *bpf)
 	if (!dev->netdev_ops->ndo_bpf)
 		return -EOPNOTSUPP;
 
+	if (dev->ethtool->hds_config == ETHTOOL_TCP_DATA_SPLIT_ENABLED &&
+	    (bpf->command == XDP_SETUP_PROG ||
+	     bpf->command == XDP_SETUP_PROG_HW) &&
+	    bpf->prog && !bpf->prog->aux->xdp_has_frags) {
+		NL_SET_ERR_MSG(bpf->extack,
+			       "unable to propagate XDP to device using tcp-data-split");
+		return -EBUSY;
+	}
+
 	if (dev_get_min_mp_channel_count(dev)) {
 		NL_SET_ERR_MSG(bpf->extack, "unable to propagate XDP to device using memory provider");
 		return -EBUSY;
@@ -9535,6 +9545,12 @@ static int dev_xdp_install(struct net_device *dev, enum bpf_xdp_mode mode,
 	struct netdev_bpf xdp;
 	int err;
 
+	if (dev->ethtool->hds_config == ETHTOOL_TCP_DATA_SPLIT_ENABLED &&
+	    prog && !prog->aux->xdp_has_frags) {
+		NL_SET_ERR_MSG(extack, "unable to install XDP to device using tcp-data-split");
+		return -EBUSY;
+	}
+
 	if (dev_get_min_mp_channel_count(dev)) {
 		NL_SET_ERR_MSG(extack, "unable to install XDP to device using memory provider");
 		return -EBUSY;
Signature · 1 line
2.34.1
maintainer
#26 lore raw

Re: [PATCH net-next v6 8/9] net: disallow setup single buffer XDP when tcp-data-split is enabled.

net/core/dev.c int dev_xdp_propagate(struct net_device *dev, struct netdev_bpf *bpf) · line 9504

Quoted 1 line · On Wed, 18 Dec 2024 14:45:29 +0000 Taehee Yoo wrote:
net/core/dev.c +1 -0
+	     bpf->command == XDP_SETUP_PROG_HW) &&

PROG_HW will be fine, you can drop this part of the check. HDS is a host feature, if the program is offloaded offload driver does much more precise geometry validation already.

author
#27 lore raw

Re: [PATCH net-next v6 8/9] net: disallow setup single buffer XDP when tcp-data-split is enabled.

Quoted 7 lines · Jakub Kicinski
Quoted 1 line · On Wed, 18 Dec 2024 14:45:29 +0000 Taehee Yoo wrote:

+ bpf->command == XDP_SETUP_PROG_HW) &&

PROG_HW will be fine, you can drop this part of the check. HDS is a host feature, if the program is offloaded offload driver does much more precise geometry validation already.

Thanks, I will remove this condition.

Thanks a lot!
Taehee Yoo

author
#28 lore raw

PATCH v6 9/9 netdevsim: add HDS feature

In reply to Taehee Yoo

HDS options(tcp-data-split, hds-thresh) have dendencies between other features like XDP. Basic dependencies are checked in the core API. netdevsim is very useful to check basic dependencies.

The default tcp-data-split mode is UNKNOWN but netdevsim driver returns DISABLED when ethtool dumps tcp-data-split mode. The default value of HDS threshold is 0 and the maximum value is 1024.

ethtool shows like this.

ethtool -g eni1np1
Ring parameters for eni1np1:
Pre-set maximums:
...
HDS thresh: 1024
Current hardware settings:
...

TCP data split:         off
HDS thresh:             0

ethtool -G eni1np1 tcp-data-split on hds-thresh 1024 ethtool -g eni1np1
Ring parameters for eni1np1:
Pre-set maximums:
...
HDS thresh: 1024
Current hardware settings:
...

TCP data split:         on
HDS thresh:             1024

---

v6:
- Patch added.

 drivers/net/netdevsim/ethtool.c   | 15 ++++++++++++++-
 drivers/net/netdevsim/netdevsim.h |  4 ++++
 2 files changed, 18 insertions(+), 1 deletion(-)
drivers/net/netdevsim/ethtool.c +14 -1
index 5fe1eaef99b5..aa176f52fc3f 100644
@@ -2,7 +2,6 @@
 // Copyright (c) 2020 Facebook
 
 #include <linux/debugfs.h>
-#include <linux/ethtool.h>
 #include <linux/random.h>
 
 #include "netdevsim.h"
@@ -72,6 +71,11 @@ static void nsim_get_ringparam(struct net_device *dev,
 	struct netdevsim *ns = netdev_priv(dev);
 
 	memcpy(ring, &ns->ethtool.ring, sizeof(ns->ethtool.ring));
+	memcpy(kernel_ring, &ns->ethtool.kernel_ring,
+	       sizeof(ns->ethtool.kernel_ring));
+
+	if (kernel_ring->tcp_data_split == ETHTOOL_TCP_DATA_SPLIT_UNKNOWN)
+		kernel_ring->tcp_data_split = ETHTOOL_TCP_DATA_SPLIT_DISABLED;
 }
 
 static int nsim_set_ringparam(struct net_device *dev,
@@ -85,6 +89,9 @@ static int nsim_set_ringparam(struct net_device *dev,
 	ns->ethtool.ring.rx_jumbo_pending = ring->rx_jumbo_pending;
 	ns->ethtool.ring.rx_mini_pending = ring->rx_mini_pending;
 	ns->ethtool.ring.tx_pending = ring->tx_pending;
+	ns->ethtool.kernel_ring.tcp_data_split = kernel_ring->tcp_data_split;
+	ns->ethtool.kernel_ring.hds_thresh = kernel_ring->hds_thresh;
+
 	return 0;
 }
 
@@ -161,6 +168,8 @@ static int nsim_get_ts_info(struct net_device *dev,
 
 static const struct ethtool_ops nsim_ethtool_ops = {
 	.supported_coalesce_params	= ETHTOOL_COALESCE_ALL_PARAMS,
+	.supported_ring_params		= ETHTOOL_RING_USE_TCP_DATA_SPLIT |
+					  ETHTOOL_RING_USE_HDS_THRS,
 	.get_pause_stats	        = nsim_get_pause_stats,
 	.get_pauseparam		        = nsim_get_pauseparam,
 	.set_pauseparam		        = nsim_set_pauseparam,
@@ -182,6 +191,10 @@ static void nsim_ethtool_ring_init(struct netdevsim *ns)
 	ns->ethtool.ring.rx_jumbo_max_pending = 4096;
 	ns->ethtool.ring.rx_mini_max_pending = 4096;
 	ns->ethtool.ring.tx_max_pending = 4096;
+
+	ns->ethtool.kernel_ring.tcp_data_split = ETHTOOL_TCP_DATA_SPLIT_UNKNOWN;
+	ns->ethtool.kernel_ring.hds_thresh = 0;
+	ns->ethtool.kernel_ring.hds_thresh_max = NSIM_HDS_THRESHOLD_MAX;
 }
 
 void nsim_ethtool_init(struct netdevsim *ns)
drivers/net/netdevsim/netdevsim.h +4 -0
index bf02efa10956..6abbc627308d 100644
@@ -16,6 +16,7 @@
 #include <linux/debugfs.h>
 #include <linux/device.h>
 #include <linux/ethtool.h>
+#include <linux/ethtool_netlink.h>
 #include <linux/kernel.h>
 #include <linux/list.h>
 #include <linux/netdevice.h>
@@ -36,6 +37,8 @@
 #define NSIM_IPSEC_VALID		BIT(31)
 #define NSIM_UDP_TUNNEL_N_PORTS		4
 
+#define NSIM_HDS_THRESHOLD_MAX		1024
+
 struct nsim_sa {
 	struct xfrm_state *xs;
 	__be32 ipaddr[4];
@@ -87,6 +90,7 @@ struct nsim_ethtool {
 	struct nsim_ethtool_pauseparam pauseparam;
 	struct ethtool_coalesce coalesce;
 	struct ethtool_ringparam ring;
+	struct kernel_ethtool_ringparam kernel_ring;
 	struct ethtool_fecparam fec;
 };
 
Signature · 1 line
2.34.1
maintainer
#29 lore raw

Re: [PATCH net-next v6 9/9] netdevsim: add HDS feature

Quoted 2 lines · On Wed, 18 Dec 2024 14:45:30 +0000 Taehee Yoo wrote:
 drivers/net/netdevsim/ethtool.c   | 15 ++++++++++++++-
 drivers/net/netdevsim/netdevsim.h |  4 ++++

netdevsim patches must come with a selftest that uses them :) We support bash, C and Python tests. Look inside tools/testing/selftests/drivers/net/
These tests could serve as examples: stats.py, hw/ncdevmem.c

TBH it doesn't look like netdevsim _actually_ supports HDS, as in forwarded packets will not be split with the current code, or linearized. You'd need to modify nsim_start_xmit() to either linearize the packet or not based on *peer's* HDS settings.

author
#30 lore raw

Re: [PATCH net-next v6 9/9] netdevsim: add HDS feature

Quoted 12 lines · Jakub Kicinski
Quoted 2 lines · On Wed, 18 Dec 2024 14:45:30 +0000 Taehee Yoo wrote:
 drivers/net/netdevsim/ethtool.c   | 15 ++++++++++++++-
 drivers/net/netdevsim/netdevsim.h |  4 ++++

netdevsim patches must come with a selftest that uses them :) We support bash, C and Python tests. Look inside tools/testing/selftests/drivers/net/
These tests could serve as examples: stats.py, hw/ncdevmem.c

Quoted 5 lines

TBH it doesn't look like netdevsim _actually_ supports HDS, as in forwarded packets will not be split with the current code, or linearized. You'd need to modify nsim_start_xmit() to either linearize the packet or not based on *peer's* HDS settings.

Ah, Sorry for the sloppy change.
I will write a selftest. Also, I will modify nsim_start_xmit() to support HDS. The example would be very helpful to me.

Thank you so much!
Taehee Yoo.

maintainer
#31 lore raw

Re: [PATCH net-next v6 9/9] netdevsim: add HDS feature

Quoted 1 line · On Thu, 19 Dec 2024 23:37:45 +0900 Taehee Yoo wrote:

The example would be very helpful to me.

Just to make sure nothing gets lost in translation, are you saying that:
- the examples of tests I listed are useful; or
- you'd appreciate examples of how to code up HDS in netdevsim; or
- you'd appreciate more suitable examples of the tests?

:)

author
#32 lore raw

Re: [PATCH net-next v6 9/9] netdevsim: add HDS feature

Quoted 10 lines · Jakub Kicinski
Quoted 1 line · On Thu, 19 Dec 2024 23:37:45 +0900 Taehee Yoo wrote:

The example would be very helpful to me.

Just to make sure nothing gets lost in translation, are you saying that:
- the examples of tests I listed are useful; or
- you'd appreciate examples of how to code up HDS in netdevsim; or
- you'd appreciate more suitable examples of the tests?

:)

Ah, I appreciate example of tests you listed are useful, Thanks!

maintainer
#33 lore raw

Re: [PATCH net-next v6 9/9] netdevsim: add HDS feature

Quoted 11 lines · On Fri, 20 Dec 2024 00:19:38 +0900 Taehee Yoo wrote:
Quoted 9 lines · On Thu, 19 Dec 2024 23:37:45 +0900 Taehee Yoo wrote:
Quoted 1 line

The example would be very helpful to me.

Just to make sure nothing gets lost in translation, are you saying that:
- the examples of tests I listed are useful; or
- you'd appreciate examples of how to code up HDS in netdevsim; or
- you'd appreciate more suitable examples of the tests?

:)

Ah, I appreciate example of tests you listed are useful, Thanks!

Okay :)

FWIW I don't expect that you'd do anything too complicated to support HDS in netdevsim. The packets generated by the networking stack are "split", already. What I was thinking is basically check if HDS is enabled, compare skb->len to threshold, and if we shouldn't HDS call skb_linearize().