rpi: Add identifiers for the new RPi 5 series
PATCH 1/1 rpi: Add identifiers for the new RPi 5 series
The Raspberry Pi foundation have released the Raspberry Pi 500, CM5 an CM5 lite devices so add the assoicated revision identifers so we can detect them.
--- board/raspberrypi/rpi/rpi.c | 15 +++++++++++++++ 1 file changed, 15 insertions(+)
board/raspberrypi/rpi/rpi.c +15 -0
@@ -193,6 +193,21 @@ static const struct rpi_model rpi_models_new_scheme[] = {DTB_DIR "bcm2712-rpi-5-b.dtb" , true, }, + [0x18] = { +"Compute Module 5" , +DTB_DIR "bcm2712-rpi-cm5-cm5io.dtb" , + true, + }, + [0x19] = { +"500" , +DTB_DIR "bcm2712-rpi-500.dtb" , + true, + }, + [0x1A] = { +"Compute Module 5 Lite" , +DTB_DIR "bcm2712-rpi-cm5l-cm5io.dtb" , + true, + }, }; static const struct rpi_model rpi_models_old_scheme[] = {
Signature · 1 line
2.47.1
Quoted 5 lines · Peter Robinson
The Raspberry Pi foundation have released the Raspberry Pi 500, CM5 an CM5 lite devices so add the assoicated revision identifers so we can detect them.
Signed-off-by Peter Robinson <[email protected]>
Quoted 30 lines
--- board/raspberrypi/rpi/rpi.c | 15 +++++++++++++++ 1 file changed, 15 insertions(+)board/raspberrypi/rpi/rpi.c +15
-0@@ -193,6 +193,21 @@ static const struct rpi_model rpi_models_new_scheme[] = {DTB_DIR "bcm2712-rpi-5-b.dtb" , true, }, + [0x18] = { +"Compute Module 5" , +DTB_DIR "bcm2712-rpi-cm5-cm5io.dtb" , + true, + }, + [0x19] = { +"500" , +DTB_DIR "bcm2712-rpi-500.dtb" , + true, + }, + [0x1A] = { +"Compute Module 5 Lite" , +DTB_DIR "bcm2712-rpi-cm5l-cm5io.dtb" , + true, + }, }; static const struct rpi_model rpi_models_old_scheme[] = {
Hi Peter,
Quoted 10 lines · Peter Robinson
The Raspberry Pi foundation have released the Raspberry Pi 500, CM5 an CM5 lite devices so add the assoicated revision identifers so we can detect them.
Signed-off-by Peter Robinson <[email protected]>--- board/raspberrypi/rpi/rpi.c | 15 +++++++++++++++ 1 file changed, 15 insertions(+)
Would it be possible to get the information below from the devicetree on the FAT partition? This is passed to U-Boot at runtime.
Since we already have the DT internally, do we need fdtfile? There are mechanisms for using U-Boot's devicetree when booting.
Quoted 27 lines
board/raspberrypi/rpi/rpi.c +15
-1@@ -193,6 +193,21 @@ static const struct rpi_model rpi_models_new_scheme[] = {DTB_DIR "bcm2712-rpi-5-b.dtb" , true, }, + [0x18] = { +"Compute Module 5" , +DTB_DIR "bcm2712-rpi-cm5-cm5io.dtb" , + true, + }, + [0x19] = { +"500" , +DTB_DIR "bcm2712-rpi-500.dtb" , + true, + }, + [0x1A] = { +"Compute Module 5 Lite" , +DTB_DIR "bcm2712-rpi-cm5l-cm5io.dtb" , + true, + }, }; static const struct rpi_model rpi_models_old_scheme[] = { --
Quoted 2 lines
2.47.1
Regards,
Simon