Skip to contentSkip to conversation

i2c-mlxbf: Add repeated start condition support

PATCH Superseded Chris Babroski 2 participants 2 messages Jan 31, 2025 – Mar 20, 2025

Subsystems (2)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 i2c-mlxbf: Add repeated start condition support

Add support for SMBus repeated start conditions to the Mellanox I2C driver. This support is specifically enabled for the I2C_FUNC_SMBUS_WRITE_I2C_BLOCK implementation which is required for communication with an I2C device on BlueField 3.

The I2C bus timing configuration values have also been updated to fix an issue found when testing block reads requiring a repeated start condition. The "timeout" value, which determines how long the clock can be held low before the I2C transaction is aborted, was too short and caused unwanted failures. It was also found that other timing values do not match the configuration that is recommended and has been verified by the BlueField HW team so those values have been updated as well.

---
V2 -> V3: Cleaned up code and address review comments V1 -> V2: Removed default "Reviewed-by:" tags

 drivers/i2c/busses/i2c-mlxbf.c | 68 +++++++++++++++++++++-------------
 1 file changed, 42 insertions(+), 26 deletions(-)
drivers/i2c/busses/i2c-mlxbf.c +42 -26
index b3a73921ab69..3f8b4574f735 100644
@@ -196,6 +196,7 @@
 
 #define MLXBF_I2C_MASK_8    GENMASK(7, 0)
 #define MLXBF_I2C_MASK_16   GENMASK(15, 0)
+#define MLXBF_I2C_MASK_32   GENMASK(31, 0)
 
 #define MLXBF_I2C_MST_ADDR_OFFSET         0x200
 
@@ -222,7 +223,7 @@
 
 #define MLXBF_I2C_MASTER_ENABLE \
 	(MLXBF_I2C_MASTER_LOCK_BIT | MLXBF_I2C_MASTER_BUSY_BIT | \
-	 MLXBF_I2C_MASTER_START_BIT | MLXBF_I2C_MASTER_STOP_BIT)
+	 MLXBF_I2C_MASTER_START_BIT)
 
 #define MLXBF_I2C_MASTER_ENABLE_WRITE \
 	(MLXBF_I2C_MASTER_ENABLE | MLXBF_I2C_MASTER_CTL_WRITE_BIT)
@@ -336,6 +337,7 @@ enum {
 	MLXBF_I2C_F_SMBUS_BLOCK = BIT(5),
 	MLXBF_I2C_F_SMBUS_PEC = BIT(6),
 	MLXBF_I2C_F_SMBUS_PROCESS_CALL = BIT(7),
+	MLXBF_I2C_F_WRITE_WITHOUT_STOP = BIT(8),
 };
 
 /* Mellanox BlueField chip type. */
@@ -694,16 +696,19 @@ static void mlxbf_i2c_smbus_read_data(struct mlxbf_i2c_priv *priv,
 }
 
 static int mlxbf_i2c_smbus_enable(struct mlxbf_i2c_priv *priv, u8 slave,
-				  u8 len, u8 block_en, u8 pec_en, bool read)
+				  u8 len, u8 block_en, u8 pec_en, bool read,
+				  bool stop)
 {
-	u32 command;
+	u32 command = 0;
 
 	/* Set Master GW control word. */
+	if (stop)
+		command |= MLXBF_I2C_MASTER_STOP_BIT;
 	if (read) {
-		command = MLXBF_I2C_MASTER_ENABLE_READ;
+		command |= MLXBF_I2C_MASTER_ENABLE_READ;
 		command |= rol32(len, MLXBF_I2C_MASTER_READ_SHIFT);
 	} else {
-		command = MLXBF_I2C_MASTER_ENABLE_WRITE;
+		command |= MLXBF_I2C_MASTER_ENABLE_WRITE;
 		command |= rol32(len, MLXBF_I2C_MASTER_WRITE_SHIFT);
 	}
 	command |= rol32(slave, MLXBF_I2C_MASTER_SLV_ADDR_SHIFT);
@@ -738,9 +743,11 @@ mlxbf_i2c_smbus_start_transaction(struct mlxbf_i2c_priv *priv,
 	u8 op_idx, data_idx, data_len, write_len, read_len;
 	struct mlxbf_i2c_smbus_operation *operation;
 	u8 read_en, write_en, block_en, pec_en;
-	u8 slave, flags, addr;
+	bool stop_after_write = true;
+	u8 slave, addr;
 	u8 *read_buf;
 	int ret = 0;
+	u32 flags;
 
 	if (request->operation_cnt > MLXBF_I2C_SMBUS_MAX_OP_CNT)
 		return -EINVAL;
@@ -799,7 +806,16 @@ mlxbf_i2c_smbus_start_transaction(struct mlxbf_i2c_priv *priv,
 			memcpy(data_desc + data_idx,
 			       operation->buffer, operation->length);
 			data_idx += operation->length;
+
+			/*
+			 * The stop condition can be skipped when writing on the bus
+			 * to implement a repeated start condition on the next read
+			 * as required for several SMBus and I2C operations.
+			 */
+			if (flags & MLXBF_I2C_F_WRITE_WITHOUT_STOP)
+				stop_after_write = false;
 		}
+
 		/*
 		 * We assume that read operations are performed only once per
 		 * SMBus transaction. *TBD* protect this statement so it won't
@@ -825,7 +841,7 @@ mlxbf_i2c_smbus_start_transaction(struct mlxbf_i2c_priv *priv,
 
 	if (write_en) {
 		ret = mlxbf_i2c_smbus_enable(priv, slave, write_len, block_en,
-					 pec_en, 0);
+					 pec_en, 0, stop_after_write);
 		if (ret)
 			goto out_unlock;
 	}
@@ -835,7 +851,7 @@ mlxbf_i2c_smbus_start_transaction(struct mlxbf_i2c_priv *priv,
 		mlxbf_i2c_smbus_write_data(priv, (const u8 *)&addr, 1,
 					   MLXBF_I2C_MASTER_DATA_DESC_ADDR, true);
 		ret = mlxbf_i2c_smbus_enable(priv, slave, read_len, block_en,
-					 pec_en, 1);
+					 pec_en, 1, true);
 		if (!ret) {
 			/* Get Master GW data descriptor. */
 			mlxbf_i2c_smbus_read_data(priv, data_desc, read_len + 1,
@@ -940,6 +956,9 @@ mlxbf_i2c_smbus_i2c_block_func(struct mlxbf_i2c_smbus_request *request,
 	request->operation[0].flags |= pec_check ? MLXBF_I2C_F_SMBUS_PEC : 0;
 	request->operation[0].buffer = command;
 
+	if (read)
+		request->operation[0].flags |= MLXBF_I2C_F_WRITE_WITHOUT_STOP;
+
 	/*
 	 * As specified in the standard, the max number of bytes to read/write
 	 * per block operation is 32 bytes. In Golan code, the controller can
@@ -1174,7 +1193,8 @@ static void mlxbf_i2c_set_timings(struct mlxbf_i2c_priv *priv,
 				     MLXBF_I2C_MASK_16, MLXBF_I2C_SHIFT_16);
 	writel(timer, priv->timer->io + MLXBF_I2C_SMBUS_THIGH_MAX_TBUF);
 
-	timer = timings->timeout;
+	timer = mlxbf_i2c_set_timer(priv, timings->timeout, false,
+				    MLXBF_I2C_MASK_32, MLXBF_I2C_SHIFT_0);
 	writel(timer, priv->timer->io + MLXBF_I2C_SMBUS_SCL_LOW_TIMEOUT);
 }
 
@@ -1184,11 +1204,7 @@ enum mlxbf_i2c_timings_config {
 	MLXBF_I2C_TIMING_CONFIG_1000KHZ,
 };
 
-/*
- * Note that the mlxbf_i2c_timings->timeout value is not related to the
- * bus frequency, it is impacted by the time it takes the driver to
- * complete data transmission before transaction abort.
- */
+/* Timing values are in nanoseconds */
 static const struct mlxbf_i2c_timings mlxbf_i2c_timings[] = {
 	[MLXBF_I2C_TIMING_CONFIG_100KHZ] = {
 		.scl_high = 4810,
@@ -1203,8 +1219,8 @@ static const struct mlxbf_i2c_timings mlxbf_i2c_timings[] = {
 		.scl_fall = 50,
 		.hold_data = 300,
 		.buf = 20000,
-		.thigh_max = 5000,
-		.timeout = 106500
+		.thigh_max = 50000,
+		.timeout = 35000000
 	},
 	[MLXBF_I2C_TIMING_CONFIG_400KHZ] = {
 		.scl_high = 1011,
@@ -1219,24 +1235,24 @@ static const struct mlxbf_i2c_timings mlxbf_i2c_timings[] = {
 		.scl_fall = 50,
 		.hold_data = 300,
 		.buf = 20000,
-		.thigh_max = 5000,
-		.timeout = 106500
+		.thigh_max = 50000,
+		.timeout = 35000000
 	},
 	[MLXBF_I2C_TIMING_CONFIG_1000KHZ] = {
-		.scl_high = 600,
-		.scl_low = 1300,
+		.scl_high = 383,
+		.scl_low = 460,
 		.hold_start = 600,
-		.setup_start = 600,
-		.setup_stop = 600,
-		.setup_data = 100,
+		.setup_start = 260,
+		.setup_stop = 260,
+		.setup_data = 50,
 		.sda_rise = 50,
 		.sda_fall = 50,
 		.scl_rise = 50,
 		.scl_fall = 50,
 		.hold_data = 300,
-		.buf = 20000,
-		.thigh_max = 5000,
-		.timeout = 106500
+		.buf = 500,
+		.thigh_max = 50000,
+		.timeout = 35000000
 	}
 };
 

base-commit: 0a9b9d17f3a781dea03baca01c835deaa07f7cc3

Signature · 1 line
2.47.0
maintainer
#1 lore raw

Hi Chris,

sorry for looking into this patch so late.

Quoted 5 lines · Chris Babroski

Add support for SMBus repeated start conditions to the Mellanox I2C driver. This support is specifically enabled for the I2C_FUNC_SMBUS_WRITE_I2C_BLOCK implementation which is required for communication with an I2C device on BlueField 3.

Quoted 7 lines

The I2C bus timing configuration values have also been updated to fix an issue found when testing block reads requiring a repeated start condition. The "timeout" value, which determines how long the clock can be held low before the I2C transaction is aborted, was too short and caused unwanted failures. It was also found that other timing values do not match the configuration that is recommended and has been verified by the BlueField HW team so those values have been updated as well.

Could we split this patches into two parts? It looks good to me, so that once you send it, I will apply it right away.

Thanks,
Andi