Skip to contentSkip to conversation

ppp: Fix KMSAN uninit-value warning with bpf

PATCH Superseded Jiayuan Chen 1 participant 2 messages Feb 22, 2025

Subsystems (4)

v3 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

v3 cover ppp: Fix KMSAN uninit-value warning with bpf

Syzbot caught an "KMSAN: uninit-value" warning [1], which is caused by the ppp driver not initializing a 2-byte header when using socket filters.

Here's a detailed explanation:

The following code can generate a PPP filter BPF program:
'''
struct bpf_program fp;
pcap_t *handle;
handle = pcap_open_dead(DLT_PPP_PPPD, 65535); pcap_compile(handle, &fp, "ip and outbound", 0, 0); bpf_dump(&fp, 1);
'''
Its output is:
'''
(000) ldh [2]
(001) jeq #0x21 jt 2 jf 5
(002) ldb [0]
(003) jeq #0x1 jt 4 jf 5
(004) ret #65535
(005) ret #0
'''

You can find similar code at the following link:
https://github.com/ppp-project/ppp/blob/master/pppd/options.c#L1680
The maintainer of this code repository is also the original maintainer of the ppp driver.

3. Current problem
The problem is that the skb->data generated by ppp_write() starts from the 'Protocol' field.

But the BPF program skips 2 bytes of data and then reads the 'Protocol' field to determine if it's an IP packet just like the comment in 'drivers/net/ppp/ppp_generic.c':
/* the filter instructions are constructed assuming
a four-byte PPP header on each packet */

In the current PPP driver implementation, to correctly use the BPF filter program, a 2-byte header is added, after running the socket filter, it's restored:
'''
1768 *(u8 *)skb_push(skb, 2) = 1;
1770 bpf_prog_run()
1782 skb_pull(skb, 2);
'''

The issue is that only the first byte indicating direction is initialized, while the second byte is not initialized. For normal BPF programs generated by libpcap, uninitialized data won't be used, so it's not a problem.

However, for carefully crafted BPF programs, such as those generated by syzkaller [2], which start reading from offset 0, the uninitialized data will be used and caught by KMSAN.

4. Fix
The fix is simple: initialize the entire 2-byte header.

Cc Paul Mackerras <[email protected]>

[1] https://syzkaller.appspot.com/bug?extid=853242d9c9917165d791
[2] https://syzkaller.appspot.com/text?tag=ReproC&x=11994913980000

Jiayuan Chen (1):
ppp: Fix KMSAN warning by initializing 2-byte header

 drivers/net/ppp/ppp_generic.c | 15 +++++++++++----
 1 file changed, 11 insertions(+), 4 deletions(-)
Signature · 1 line
2.47.1
#1 lore raw

PATCH v3 1/1 ppp: Fix KMSAN warning by initializing 2-byte header

The PPP driver adds an extra 2-byte header to enable socket filters to run correctly. However, the driver only initializes the first byte, which indicates the direction. For normal BPF programs, this is not a problem since they only read the first byte.

Nevertheless, for carefully crafted BPF programs, if they read the second byte, this will trigger a KMSAN warning for reading uninitialized data.

---
 drivers/net/ppp/ppp_generic.c | 15 +++++++++++----
 1 file changed, 11 insertions(+), 4 deletions(-)
drivers/net/ppp/ppp_generic.c +11 -4
index 4583e15ad03a..29a7a21cb096 100644
@@ -1762,10 +1762,17 @@ ppp_send_frame(struct ppp *ppp, struct sk_buff *skb)
 
 	if (proto < 0x8000) {
 #ifdef CONFIG_PPP_FILTER
-		/* check if we should pass this packet */
-		/* the filter instructions are constructed assuming
-		   a four-byte PPP header on each packet */
-		*(u8 *)skb_push(skb, 2) = 1;
+		/* Check if we should pass this packet.
+		 * The filter instructions are constructed assuming
+		 * a four-byte PPP header on each packet. The first byte
+		 * indicates the direction, and the second byte is meaningless,
+		 * but we still need to initialize it to prevent crafted BPF
+		 * programs from reading them which would cause reading of
+		 * uninitialized data.
+		 */
+		skb_push(skb, 2);
+		skb->data[0] = 1;
+		skb->data[1] = 0;
 		if (ppp->pass_filter &&
 		    bpf_prog_run(ppp->pass_filter, skb) == 0) {
 			if (ppp->debug & 1)
Signature · 1 line
2.47.1