airoha: add support spi/mmc/ethernet
Subsystems (6)
cover airoha: add support spi/mmc/ethernet
This is continuation of the initial patchset for airoha support.
Some are trivial fix for spi.
A new concept to setup SPI from detected NAND.
Sadly DTS node still need to be merged upstream so we are currently adding them to u-boot dtsi and it's planned to be dropped once they are accepted in upstream kernel.
Christian Marangi (14):
arch: arm: dts: an7581: add Chip SCU node
net: airoha: Add Airoha Ethernet driver
airoha: Add Ethernet config to defconfig
arch: arm: dts: an7581: Add Ethernet nodes
mmc: mediatek: permit to also build for Airoha arch
arch: arm: dts: an7581: Add eMMC nodes
airoha: Add eMMC config to defconfig
regmap: Add regmap_set/clear_bits shorthands
spi: drop unneeded spi.h header include from spinand.h
spi: Introduce setup_for_spinand()
spinand: call SPI setup_for_spinand if supported
spi: airoha: Add Airoha SPI NAND driver
arm: dts: an7581: Add SNAND node
configs: airoha: an7581_evb: Enable Airoha SNFI SPI config
arch/arm/dts/an7581-u-boot.dtsi | 90 ++ configs/an7581_evb_defconfig | 3 + drivers/mmc/Kconfig | 2 +- drivers/mtd/nand/spi/core.c | 18 + drivers/net/Kconfig | 8 + drivers/net/Makefile | 1 + drivers/net/airoha_eth.c | 1448 +++++++++++++++++++++++++++++++ drivers/spi/Kconfig | 9 + drivers/spi/Makefile | 1 + drivers/spi/airoha_snfi_spi.c | 717 +++++++++++++++ include/linux/mtd/spinand.h | 2 +- include/regmap.h | 28 + include/spi.h | 11 + 13 files changed, 2336 insertions(+), 2 deletions(-) create mode 100644 drivers/net/airoha_eth.c create mode 100644 drivers/spi/airoha_snfi_spi.c
Signature · 1 line
2.48.1
PATCH 1/14 arch: arm: dts: an7581: add Chip SCU node
Add pending Chip SCU node for clock node.
--- arch/arm/dts/an7581-u-boot.dtsi | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm/dts/an7581-u-boot.dtsi +7 -0
@@ -11,6 +11,13 @@ reg = <0x0 0x80000000 0x0 0x40000>; }; }; + + soc { + chip_scu: syscon@1fa20000 { + compatible = "airoha,en7581-chip-scu", "syscon"; + reg = <0x0 0x1fa20000 0x0 0x388>; + }; + }; }; &uart1 {
Signature · 1 line
2.48.1
PATCH 2/14 net: airoha: Add Airoha Ethernet driver
In reply to Christian MarangiAdd airoha Ethernet driver for Airoha AN7581 SoC. This is a majorly rewritten and simplified version of the Linux airoha_eth.c driver.
It's has been modified to support a single RX/TX ring to reflect U-Boot implementation with recv and send API.
The struct and the define are kept as similar as possible to upstream one to not diverge too much.
The AN7581 SoC include an Ethernet Switch based on the Mediatek MT753x but doesn't require any modification aside from setting the CPU port and applying the Flood configuration hence it can be handled entirely in the Ethernet driver.
--- drivers/net/Kconfig | 8 + drivers/net/Makefile | 1 + drivers/net/airoha_eth.c | 1448 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 1457 insertions(+) create mode 100644 drivers/net/airoha_eth.c
drivers/net/Kconfig +8 -0
@@ -122,6 +122,14 @@ config AG7XXX This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips. +config AIROHA_ETH + bool "Airoha Ethernet QDMA Driver" + depends on ARCH_AIROHA + select PHYLIB + select DM_RESET + help + This Driver support Airoha Ethernet QDMA Driver + Say Y to enable support for the Airoha Ethernet QDMA. config ALTERA_TSE bool "Altera Triple-Speed Ethernet MAC support"
drivers/net/Makefile +1 -0
@@ -5,6 +5,7 @@ obj-$(CONFIG_AG7XXX) += ag7xxx.o +obj-$(CONFIG_AIROHA_ETH) += airoha_eth.o obj-$(CONFIG_ALTERA_TSE) += altera_tse.o obj-$(CONFIG_ASPEED_MDIO) += aspeed_mdio.o obj-$(CONFIG_BCM6348_ETH) += bcm6348-eth.o
drivers/net/airoha_eth.c new file +1448 -0
1,448 lines not on this page · raw message
Signature · 1 line
2.48.1
Re: [PATCH 02/14] net: airoha: Add Airoha Ethernet driver
Quoted 14 lines · Christian Marangi
Add airoha Ethernet driver for Airoha AN7581 SoC. This is a majorly rewritten and simplified version of the Linux
airoha_eth.cdriver.It's has been modified to support a single RX/TX ring to reflect U-Boot implementation with recv and send API.
The struct and the define are kept as similar as possible to upstream one to not diverge too much.
The AN7581 SoC include an Ethernet Switch based on the Mediatek MT753x but doesn't require any modification aside from setting the CPU port and applying the Flood configuration hence it can be handled entirely in the Ethernet driver.
Quoted 7 lines
Signed-off-by Christian Marangi <[email protected]>--- drivers/net/Kconfig | 8 + drivers/net/Makefile | 1 + drivers/net/airoha_eth.c | 1448 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 1457 insertions(+) create mode 100644 drivers/net/airoha_eth.c
checkpatch.pl has some macro warnings and it looks like some inconsistent spacing around '#define FOO' vs '#define<tab>FOO' ? And are all of those defines needed?
Signature · 1 line
Tom
Re: [PATCH 02/14] net: airoha: Add Airoha Ethernet driver
Quoted 24 lines · Tom Rini
Quoted 14 lines · Christian Marangi
Add airoha Ethernet driver for Airoha AN7581 SoC. This is a majorly rewritten and simplified version of the Linux
airoha_eth.cdriver.It's has been modified to support a single RX/TX ring to reflect U-Boot implementation with recv and send API.
The struct and the define are kept as similar as possible to upstream one to not diverge too much.
The AN7581 SoC include an Ethernet Switch based on the Mediatek MT753x but doesn't require any modification aside from setting the CPU port and applying the Flood configuration hence it can be handled entirely in the Ethernet driver.
Quoted 7 lines
Signed-off-by Christian Marangi <[email protected]>--- drivers/net/Kconfig | 8 + drivers/net/Makefile | 1 + drivers/net/airoha_eth.c | 1448 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 1457 insertions(+) create mode 100644 drivers/net/airoha_eth.c
Quoted 4 lines
checkpatch.pl has some macro warnings and it looks like some inconsistent spacing around '#define FOO' vs '#define<tab>FOO' ? And are all of those defines needed?
No they are not all needed, I defined them for consistency with the original driver. Should I drop them?
For the checkpatch check, also comes from the original driver.
Signature · 1 line
Ansuel
Re: [PATCH 02/14] net: airoha: Add Airoha Ethernet driver
Quoted 30 lines · Christian Marangi
Quoted 24 lines · Tom Rini
Quoted 14 lines · Christian Marangi
Add airoha Ethernet driver for Airoha AN7581 SoC. This is a majorly rewritten and simplified version of the Linux
airoha_eth.cdriver.It's has been modified to support a single RX/TX ring to reflect U-Boot implementation with recv and send API.
The struct and the define are kept as similar as possible to upstream one to not diverge too much.
The AN7581 SoC include an Ethernet Switch based on the Mediatek MT753x but doesn't require any modification aside from setting the CPU port and applying the Flood configuration hence it can be handled entirely in the Ethernet driver.
Quoted 7 lines
Signed-off-by Christian Marangi <[email protected]>--- drivers/net/Kconfig | 8 + drivers/net/Makefile | 1 + drivers/net/airoha_eth.c | 1448 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 1457 insertions(+) create mode 100644 drivers/net/airoha_eth.cQuoted 4 lines
checkpatch.pl has some macro warnings and it looks like some inconsistent spacing around '#define FOO' vs '#define<tab>FOO' ? And are all of those defines needed?
Quoted 4 lines
No they are not all needed, I defined them for consistency with the original driver. Should I drop them?
For the checkpatch check, also comes from the original driver.
I guess if it will make long term re-syncs easier, we can ignore them. But the macro thing should likely be addressed upstream too?
Signature · 1 line
Tom
Re: [PATCH 02/14] net: airoha: Add Airoha Ethernet driver
Quoted 31 lines · Tom Rini
Quoted 30 lines · Christian Marangi
Quoted 28 lines · Tom Rini
Quoted 14 lines · Christian Marangi
Add airoha Ethernet driver for Airoha AN7581 SoC. This is a majorly rewritten and simplified version of the Linux
airoha_eth.cdriver.It's has been modified to support a single RX/TX ring to reflect U-Boot implementation with recv and send API.
The struct and the define are kept as similar as possible to upstream one to not diverge too much.
The AN7581 SoC include an Ethernet Switch based on the Mediatek MT753x but doesn't require any modification aside from setting the CPU port and applying the Flood configuration hence it can be handled entirely in the Ethernet driver.
Quoted 7 lines
Signed-off-by Christian Marangi <[email protected]>--- drivers/net/Kconfig | 8 + drivers/net/Makefile | 1 + drivers/net/airoha_eth.c | 1448 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 1457 insertions(+) create mode 100644 drivers/net/airoha_eth.ccheckpatch.pl has some macro warnings and it looks like some inconsistent spacing around '#define FOO' vs '#define<tab>FOO' ? And are all of those defines needed?
Quoted 8 lines
Quoted 4 lines
No they are not all needed, I defined them for consistency with the original driver. Should I drop them?
For the checkpatch check, also comes from the original driver.
I guess if it will make long term re-syncs easier, we can ignore them. But the macro thing should likely be addressed upstream too?
Ehh ethernet driver are always very different compared to the upstream version. I think I will just remove additional define not needed in v2.
Signature · 1 line
Ansuel
PATCH 3/14 airoha: Add Ethernet config to defconfig
In reply to Christian MarangiAdd Ethrnet config to defconfig to enable Ethernet support.
--- configs/an7581_evb_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/an7581_evb_defconfig +1 -0
@@ -76,3 +76,4 @@ CONFIG_SYS_NS16550=y CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_SHA512=y +CONFIG_AIROHA_ETH=y
Signature · 1 line
2.48.1
PATCH 4/14 arch: arm: dts: an7581: Add Ethernet nodes
In reply to Christian MarangiAdd Ethrnet nodes for Airoha AN7581 EVB board.
--- arch/arm/dts/an7581-u-boot.dtsi | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+)
arch/arm/dts/an7581-u-boot.dtsi +30 -0
@@ -1,5 +1,7 @@ // SPDX-License-Identifier: GPL-2.0+ +#include <dt-bindings/reset/airoha,en7581-reset.h> + / { reserved-memory { #address-cells = <2>;
@@ -17,9 +19,37 @@ compatible = "airoha,en7581-chip-scu", "syscon"; reg = <0x0 0x1fa20000 0x0 0x388>; }; + + eth: ethernet@1fb50000 { + compatible = "airoha,en7581-eth"; + reg = <0 0x1fb50000 0 0x2600>, + <0 0x1fb54000 0 0x2000>, + <0 0x1fb56000 0 0x2000>; + reg-names = "fe", "qdma0", "qdma1"; + + resets = <&scuclk EN7581_FE_RST>, + <&scuclk EN7581_FE_PDMA_RST>, + <&scuclk EN7581_FE_QDMA_RST>, + <&scuclk EN7581_DUAL_HSI0_MAC_RST>, + <&scuclk EN7581_DUAL_HSI1_MAC_RST>, + <&scuclk EN7581_HSI_MAC_RST>, + <&scuclk EN7581_XFP_MAC_RST>; + reset-names = "fe", "pdma", "qdma", + "hsi0-mac", "hsi1-mac", "hsi-mac", + "xfp-mac"; + }; + + switch: switch@1fb58000 { + compatible = "airoha,en7581-switch"; + reg = <0 0x1fb58000 0 0x8000>; + }; }; }; +&scuclk { + compatible = "airoha,en7581-scu", "syscon"; +}; + &uart1 { bootph-all; };
Signature · 1 line
2.48.1
PATCH 5/14 mmc: mediatek: permit to also build for Airoha arch
In reply to Christian MarangiAiroha new SoC implement the same Mediatek driver for MMC. Permit to also build for Airoha arch.
--- drivers/mmc/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mmc/Kconfig +1 -1
@@ -860,7 +860,7 @@ config FTSDC010_SDIO config MMC_MTK bool "MediaTek SD/MMC Card Interface support" - depends on ARCH_MEDIATEK || ARCH_MTMIPS + depends on ARCH_MEDIATEK || ARCH_MTMIPS || ARCH_AIROHA depends on OF_CONTROL help This selects the MediaTek(R) Secure digital and Multimedia card Interface.
Signature · 1 line
2.48.1
PATCH 6/14 arch: arm: dts: an7581: Add eMMC nodes
In reply to Christian MarangiAdd eMMC nodes with the fixed regulator and fixed clock. It's also needed to assign the clock and set it to 200MHz as it's set to 150Mhz by default.
--- arch/arm/dts/an7581-u-boot.dtsi | 33 +++++++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+)
arch/arm/dts/an7581-u-boot.dtsi +33 -0
@@ -14,6 +14,21 @@ }; }; + clk25m: oscillator { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + clock-output-names = "clkxtal"; + }; + + vmmc_3v3: regulator-vmmc-3v3 { + compatible = "regulator-fixed"; + regulator-name = "vmmc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + soc { chip_scu: syscon@1fa20000 { compatible = "airoha,en7581-chip-scu", "syscon";
@@ -43,6 +58,24 @@ compatible = "airoha,en7581-switch"; reg = <0 0x1fb58000 0 0x8000>; }; + + mmc0: mmc@1fa0e000 { + compatible = "mediatek,mt7622-mmc"; + reg = <0x0 0x1fa0e000 0x0 0x1000>, + <0x0 0x1fa0c000 0x0 0x60>; + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&scuclk EN7581_CLK_EMMC>, <&clk25m>; + clock-names = "source", "hclk"; + bus-width = <4>; + max-frequency = <52000000>; + vmmc-supply = <&vmmc_3v3>; + disable-wp; + cap-mmc-highspeed; + non-removable; + + assigned-clocks = <&scuclk EN7581_CLK_EMMC>; + assigned-clock-rates = <200000000>; + }; }; };
Signature · 1 line
2.48.1
PATCH 7/14 airoha: Add eMMC config to defconfig
In reply to Christian MarangiEnable Mediatek MMC driver in Airoha AN7581 EVB defconfig to add support for it in default images.
--- configs/an7581_evb_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/an7581_evb_defconfig +1 -0
@@ -77,3 +77,4 @@ CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_SHA512=y CONFIG_AIROHA_ETH=y +CONFIG_MMC_MTK=y
Signature · 1 line
2.48.1
PATCH 8/14 regmap: Add regmap_set/clear_bits shorthands
In reply to Christian MarangiPort Linux kernel regmap_set/clear_bits shorthands to set and clear bits in a regmap. These are handy if only specific bits needs to be applied or cleared and makes it easier to port regmap based driver from kernel upstream.
--- include/regmap.h | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+)
include/regmap.h +28 -0
@@ -361,6 +361,34 @@ int regmap_raw_read_range(struct regmap *map, uint range_num, uint offset,*/ int regmap_update_bits (struct regmap *map,uint offset,uint mask,uint val); +/** +* regmap_set_bits() - Set bits to a regmap +* +* @map: Regmap to write bits to +* @offset: Offset in the regmap to write to +* @bits: Bits to set to the regmap at the specified offset +* +* Return: 0 if OK, -ve on error +*/ +static inline int regmap_set_bits (struct regmap *map,uint offset,uint bits) +{ +return regmap_update_bits (map, offset, bits, bits); +} + +/** +* regmap_clear_bits() - Clear bits to a regmap +* +* @map: Regmap to write bits to +* @offset: Offset in the regmap to write to +* @bits: Bits to clear to the regmap at the specified offset +* +* Return: 0 if OK, -ve on error +*/ +static inline int regmap_clear_bits (struct regmap *map,uint offset,uint bits) +{ +return regmap_update_bits (map, offset, bits,0 ); +} +/** * regmap_init_mem() - Set up a new register map that uses memory access *
Signature · 1 line
2.48.1
PATCH 9/14 spi: drop unneeded spi.h header include from spinand.h
In reply to Christian MarangiDrop unneeded spi.h header include from spinand.h, nothing included by spi.h is actually used in this header and .c should correctly included spi.h if actually needed.
Replace spi.h with linux/bitops.h as this is what is actually required for spinand.h
--- include/linux/mtd/spinand.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
include/linux/mtd/spinand.h +1 -1
@@ -17,7 +17,7 @@#include <linux/spi/spi.h> #include <linux/spi/spi-mem.h> #else -#include <spi.h> +#include <linux/bitops.h> #include <spi-mem.h> #include <linux/mtd/nand.h> #endif
Signature · 1 line
2.48.1
PATCH 10/14 spi: Introduce setup_for_spinand()
In reply to Christian MarangiA common device attached to SPI are SPI NAND and some device might require to have info on the attached NAND to know the flash page size and spare size.
To support this, introduce setup_for_spinand() that pass the attached spinand info from manufacturer.
--- include/spi.h | 11 +++++++++++ 1 file changed, 11 insertions(+)
include/spi.h +11 -0
@@ -10,6 +10,7 @@#define _SPI_H_#include <linux/bitops.h> +#include <linux/mtd/spinand.h> /* SPI mode flags */ #define SPI_CPHA BIT(0)/* clock phase (1 = SPI_CLOCK_PHASE_SECOND) */
@@ -537,6 +538,16 @@ struct dm_spi_ops {*/ int (*get_mmap)(struct udevice *dev,ulong *map_basep,uint *map_sizep,uint *offsetp); + +/** +* setup_for_spinand() - Setup the SPI for attached SPI NAND +* +* @dev: The SPI flash slave device +* @spinand_info: The SPI NAND info to configure for +* @return 0 if OK, -ve value on error +*/ +int (*setup_for_spinand)(struct spi_slave *slave, +const struct spinand_info *spinand_info); };struct dm_spi_emul_ops {
Signature · 1 line
2.48.1
PATCH 11/14 spinand: call SPI setup_for_spinand if supported
In reply to Christian MarangiCall SPI setup_for_spinand() if supported and defined to configure the SPI slave for the attached NAND. This is needed to configure the SPI with the NAND page size and spare size for correct configuration of the device.
Call it as soon as the NAND is detected to correctly handle SPI controller with select_op_variant detection.
--- drivers/mtd/nand/spi/core.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)
drivers/mtd/nand/spi/core.c +18 -0
@@ -941,6 +941,19 @@ spinand_select_op_variant(struct spinand_device *spinand,return NULL ; } +static int spinand_setup_slave (struct spinand_device *spinand, +const struct spinand_info *spinand_info) +{ +struct spi_slave *slave = spinand->slave; +struct udevice *bus = slave->dev->parent; +struct dm_spi_ops *ops =spi_get_ops (bus); + +if (!ops->setup_for_spinand) +return 0 ; + +return ops->setup_for_spinand (slave, spinand_info); +} +/** * spinand_match_and_init() - Try to find a match between a device ID and an * entry in a spinand_info table
@@ -964,6 +977,7 @@ int spinand_match_and_init(struct spinand_device *spinand,u8 *id = spinand->id.data;struct nand_device *nand =spinand_to_nand (spinand);unsigned int i; +int ret;for (i =0 ; i < table_size; i++) {const struct spinand_info *info = &table[i];
@@ -975,6 +989,10 @@ int spinand_match_and_init(struct spinand_device *spinand,if (memcmp (id +1 , info->devid.id, info->devid.len))continue ; + ret =spinand_setup_slave (spinand, info); +if (ret) +return ret; + nand->memorg = table[i].memorg; nand->eccreq = table[i].eccreq; spinand->eccinfo = table[i].eccinfo;
Signature · 1 line
2.48.1
PATCH 12/14 spi: airoha: Add Airoha SPI NAND driver
In reply to Christian MarangiAdd Airoha SPI NAND driver to permit usage of attached SNAND on the Airoha AN7581 SoC. While SPI controller supports DMA transation, due to U-Boot limitation we currently limit it to single command in Manual mode.
--- drivers/spi/Kconfig | 9 + drivers/spi/Makefile | 1 + drivers/spi/airoha_snfi_spi.c | 717 ++++++++++++++++++++++++++++++++++ 3 files changed, 727 insertions(+) create mode 100644 drivers/spi/airoha_snfi_spi.c
drivers/spi/Kconfig +9 -0
@@ -52,6 +52,15 @@ config SPI_DIRMAP if DM_SPI +config AIROHA_SNFI_SPI + bool "Airoha SPI memory controller driver" + depends on SPI_MEM + help + Enable the Airoha SPI memory controller driver. This driver is + originally based on the Airoha SNFI IP core. It can only be + used to access SPI memory devices like SPI-NOR or SPI-NAND on + platforms embedding this IP core, like AN7581. + config ALTERA_SPI bool "Altera SPI driver" help
drivers/spi/Makefile +1 -0
@@ -19,6 +19,7 @@ obj-y += spi.o obj-$(CONFIG_SPI_MEM) += spi-mem-nodm.o endif +obj-$(CONFIG_AIROHA_SNFI_SPI) += airoha_snfi_spi.o obj-$(CONFIG_ALTERA_SPI) += altera_spi.o obj-$(CONFIG_APPLE_SPI) += apple_spi.o obj-$(CONFIG_ATH79_SPI) += ath79_spi.o
drivers/spi/airoha_snfi_spi.c new file +717 -0
717 lines not on this page · raw message
Signature · 1 line
2.48.1
PATCH 13/14 arm: dts: an7581: Add SNAND node
In reply to Christian MarangiAdd SNAND node to Airoha AN7581 EVB DTS to enable support for attached SNAND flash.
--- arch/arm/dts/an7581-u-boot.dtsi | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+)
arch/arm/dts/an7581-u-boot.dtsi +20 -0
@@ -59,6 +59,26 @@ reg = <0 0x1fb58000 0 0x8000>; }; + snfi: spi@1fa10000 { + compatible = "airoha,en7581-snand"; + reg = <0x0 0x1fa10000 0x0 0x140>, + <0x0 0x1fa11000 0x0 0x600>; + + clocks = <&scuclk EN7523_CLK_SPI>; + clock-names = "spi"; + + #address-cells = <1>; + #size-cells = <0>; + + spi_nand: nand@0 { + compatible = "spi-nand"; + reg = <0>; + spi-max-frequency = <50000000>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <2>; + }; + }; + mmc0: mmc@1fa0e000 { compatible = "mediatek,mt7622-mmc"; reg = <0x0 0x1fa0e000 0x0 0x1000>,
Signature · 1 line
2.48.1
PATCH 14/14 configs: airoha: an7581_evb: Enable Airoha SNFI SPI config
In reply to Christian MarangiEnable Airoha SNFI SPI config to enable support for SNAND flash.
--- configs/an7581_evb_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/an7581_evb_defconfig +1 -0
@@ -78,3 +78,4 @@ CONFIG_DM_SPI=y CONFIG_SHA512=y CONFIG_AIROHA_ETH=y CONFIG_MMC_MTK=y +CONFIG_AIROHA_SNFI_SPI=y
Signature · 1 line
2.48.1