Skip to contentSkip to conversation

RB1 fixes

PATCH New Sumit Garg 1 participant 3 messages Apr 7, 2025 Arm (32-bit)

lore
Share & tools
lore

Sumit Garg

author
#0 lore raw

cover RB1 fixes

The eMMC on RB1 boards supports HS200 mode but currently the msm_shdci driver in U-Boot is missing DLL configuration required for HS200 mode to work. Hence disable HS200 for now until proper support is in place.

Apart from that, add DT override for USB to work in host mode as otg mode isn't supported. Along with that disable sdhci_2 which doesn't work as of now.

There is another patch related to clk_stub posted here [1] which allows the MMC clocks to be probed properly.

[1] https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/

Sumit Garg (2):
arm: dts: Add override for RB1
qcom_defconfig: Disable MMC HS200 mode support

 arch/arm/dts/qrb2210-rb1-u-boot.dtsi | 11 +++++++++++
 configs/qcom_defconfig               |  1 -
 2 files changed, 11 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/qrb2210-rb1-u-boot.dtsi
Signature · 1 line
2.43.0
author
#1 lore raw

PATCH 1/2 arm: dts: Add override for RB1

Add U-Boot override for RB1 to for USB in host mode as OTG mode isn't supported. Also, disable sdhc_2 as it's currently not supported, sdhc_1 works fine though.

---
 arch/arm/dts/qrb2210-rb1-u-boot.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)
 create mode 100644 arch/arm/dts/qrb2210-rb1-u-boot.dtsi
arch/arm/dts/qrb2210-rb1-u-boot.dtsi new file +11 -0
new file mode 100644
index 00000000000..1e136ee405a
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* This is usually OTG but U-Boot doesn't support that properly */
+&usb_dwc3 {
+	dr_mode = "host";
+};
+
+/* SDHC_2 isn't supported in U-Boot as of now */
+&sdhc_2 {
+	status = "disabled";
+};
Signature · 1 line
2.43.0
author
#2 lore raw

PATCH 2/2 qcom_defconfig: Disable MMC HS200 mode support

In reply to Sumit Garg

Currently the msm_sdhci doesn't yet support DLL configurations which are required to enable bus speeds greater that 100MHz. So disable HS200 mode support as of now as it requires bus speeds of 200MHz.

This should fix eMMC issues reported on RB1.

---
 configs/qcom_defconfig | 1 -
 1 file changed, 1 deletion(-)
configs/qcom_defconfig +0 -1
index a2b54b95f19..537806450dc 100644
@@ -81,7 +81,6 @@ CONFIG_QCOM_HYP_SMMU=y
 CONFIG_MISC=y
 CONFIG_NVMEM=y
 CONFIG_I2C_EEPROM=y
-CONFIG_MMC_HS200_SUPPORT=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ADMA=y
 CONFIG_MMC_SDHCI_MSM=y
Signature · 1 line
2.43.0