Support MSM8916 USB PHY + UDC in qcom_defconfig
Subsystems (2)
cover Support MSM8916 USB PHY + UDC in qcom_defconfig
The MSM8916 SoC includes a ChipIdea UDC. The U-Boot driver for this UDC is quite old, and did not support USB gadget driver model. As a result, it could not be built alongside the DWC3 driver. This meant that qcom_defconfig could not include support for USB on MSM8916.
This series adds support to build ChipIdea UDC with DM_USB_GADGET and ensures that the newly introduced driver is registered from the MSM EHCI glue driver.
The ChipIdea UDC driver continues to work without DM_USB_GADGET. I tested these changes by building dragonboard410c_defconfig (which does not enable DM_USB_GADGET), booting it, and then chain-booting (via fastboot) another u-boot build built with qcom_defconfig. USB gadget mode worked in both builds.
---
Sam Day (3):
usb: udc: ci: support USB gadget driver model
usb: host: ehci-msm: Register ChipIdea UDC from glue wrapper
qcom_defconfig: Enable MSM8916 USB PHY + ChipIdea UDC
configs/qcom_defconfig | 6 ++++ drivers/usb/gadget/ci_udc.c | 84 ++++++++++++++++++++++++++++++++++++++++++++- drivers/usb/host/ehci-msm.c | 7 ++++ 3 files changed, 96 insertions(+), 1 deletion(-)
---
base-commit: a40fc5afaec079ee4e621965fed18dcc94240d8c
change-id: 20250412-msm8916-usb-a1dc93c01bd5
prerequisite-message-id: <[email protected]>
prerequisite-patch-id: 006e55423a2d28cc23ff11035da672b418ebec51
prerequisite-patch-id: 8c51357ca78f0465407e0a74fda666a3e540f6d8
prerequisite-patch-id: 68d707d65315e9ea7c61ba97c58257ea9a3e3152
prerequisite-patch-id: 514522633917dd1efd2380a53949c5e7ff5ff0dd
prerequisite-patch-id: 9ee7e8f41aa3070f802d087bd763ab384e681adb
prerequisite-patch-id: fbfd19c0f729fe157c31bc40d48d19d0083d23a4
Best regards,
Signature · 1 line
Sam Day <[email protected]>
PATCH 1/3 usb: udc: ci: support USB gadget driver model
When CONFIG_DM_USB_GADGET is enabled, a UCLASS_USB_GADGET_GENERIC driver will be defined that wraps the ChipIdea UDC operations. The (dm_)?usb_gadget_.* symbols will no longer be defined (as these are now handled by the UDC uclass).
If CONFIG_DM_USB_GADGET is not enabled, this driver behaves as it previously did.
This new driver does not declare any compatibles of its own. It requires a glue driver to bind it. The ehci_msm driver will be updated in the following commit to do exactly that.
--- drivers/usb/gadget/ci_udc.c | 84 ++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 83 insertions(+), 1 deletion(-)
drivers/usb/gadget/ci_udc.c +83 -1
@@ -10,6 +10,7 @@#include <command.h> #include <config.h> #include <cpu_func.h> +#include <dm.h> #include <net.h> #include <malloc.h> #include <wait_bit.h>
@@ -94,8 +95,18 @@ static struct usb_request * ci_ep_alloc_request(struct usb_ep *ep, unsigned int gfp_flags);static void ci_ep_free_request (struct usb_ep *ep,struct usb_request *_req); +#if CONFIG_IS_ENABLED (DM_USB_GADGET ) +static int ci_udc_gadget_start (struct usb_gadget *g, +struct usb_gadget_driver *driver); +static int ci_udc_gadget_stop (struct usb_gadget *g); +#endif +static const struct usb_gadget_ops ci_udc_ops = { .pullup = ci_pullup, +#if CONFIG_IS_ENABLED(DM_USB_GADGET) + .udc_start = ci_udc_gadget_start, + .udc_stop = ci_udc_gadget_stop, +#endif };static const struct usb_ep_ops ci_ep_ops = {
@@ -927,7 +938,7 @@ void udc_irq(void) } } -int dm_usb_gadget_handle_interrupts (struct udevice *dev) +static int ci_udc_handle_interrupts (struct udevice *dev) {struct ci_udc *udc = (struct ci_udc *)controller.ctrl->hcor;u32 value;
@@ -1072,6 +1083,71 @@ static int ci_udc_probe(void)return 0 ; } +#if CONFIG_IS_ENABLED (DM_USB_GADGET ) +static int ci_udc_generic_probe (struct udevice *dev) +{ +int ret; +#if CONFIG_IS_ENABLED (DM_USB ) + ret =usb_setup_ehci_gadget (&controller.ctrl); +#else + ret =usb_lowlevel_init (0 ,USB_INIT_DEVICE , (void **)&controller.ctrl); +#endif +if (ret) +return ret; + + ret =ci_udc_probe (); +if (ret) +return ret; + +return usb_add_gadget_udc ((struct device *)dev, &controller.gadget); +} + +static int ci_udc_generic_remove (struct udevice *dev) +{ +usb_del_gadget_udc (&controller.gadget); + +if (IS_ENABLED (CONFIG_DM_USB )) { +usb_remove_ehci_gadget (&controller.ctrl); + }else { +usb_lowlevel_stop (0 ); + controller.ctrl =NULL ; + } + +return 0 ; +} + +static const struct usb_gadget_generic_ops ci_udc_generic_ops = { + .handle_interrupts = ci_udc_handle_interrupts, +}; + +U_BOOT_DRIVER (ci_udc_generic) = { + .name ="ci-udc" , + .id =UCLASS_USB_GADGET_GENERIC , + .ops = &ci_udc_generic_ops, + .probe = ci_udc_generic_probe, + .remove = ci_udc_generic_remove, +}; + +static int ci_udc_gadget_start (struct usb_gadget *g, +struct usb_gadget_driver *driver) +{ + controller.driver = driver; +return 0 ; +} + +static int ci_udc_gadget_stop (struct usb_gadget *g) +{ + controller.driver =NULL ; +udc_disconnect (); + +ci_ep_free_request (&controller.ep[0 ].ep, &controller.ep0_req->req); +free (controller.items_mem); +free (controller.epts); + +return 0 ; +} + +#else int usb_gadget_register_driver (struct usb_gadget_driver *driver) {int ret;
@@ -1126,6 +1202,12 @@ int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) return 0; } +int dm_usb_gadget_handle_interrupts (struct udevice *dev) +{ +return ci_udc_handle_interrupts (dev); +} +#endif +bool dfu_usb_get_reset (void ) {struct ci_udc *udc = (struct ci_udc *)controller.ctrl->hcor;
Signature · 1 line
2.49.0
Re: [PATCH 1/3] usb: udc: ci: support USB gadget driver model
Quoted 5 lines · Sam Day
When
CONFIG_DM_USB_GADGETis enabled, aUCLASS_USB_GADGET_GENERICdriver will be defined that wraps the ChipIdea UDC operations. The (dm_)?usb_gadget_.* symbols will no longer be defined (as these are now handled by the UDC uclass).
Quoted 8 lines
If
CONFIG_DM_USB_GADGETis not enabled, this driver behaves as it previously did.This new driver does not declare any compatibles of its own. It requires a glue driver to bind it. The
ehci_msmdriver will be updated in the following commit to do exactly that.Signed-off-by Sam Day <[email protected]>
Thanks a lot for working on this. Seems to work without problems on my dragonboard410c. Just some minor nits below to reduce code duplication.
Quoted 57 lines
--- drivers/usb/gadget/ci_udc.c | 84 ++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 83 insertions(+), 1 deletion(-)drivers/usb/gadget/ci_udc.c +21
-1@@ -10,6 +10,7 @@#include <command.h> #include <config.h> #include <cpu_func.h> +#include <dm.h> #include <net.h> #include <malloc.h> #include <wait_bit.h> @@ -94,8 +95,18 @@ static struct usb_request * ci_ep_alloc_request(struct usb_ep *ep, unsigned int gfp_flags);static void ci_ep_free_request (struct usb_ep *ep,struct usb_request *_req); +#if CONFIG_IS_ENABLED (DM_USB_GADGET ) +static int ci_udc_gadget_start (struct usb_gadget *g, +struct usb_gadget_driver *driver); +static int ci_udc_gadget_stop (struct usb_gadget *g); +#endif +static const struct usb_gadget_ops ci_udc_ops = { .pullup = ci_pullup, +#if CONFIG_IS_ENABLED(DM_USB_GADGET) + .udc_start = ci_udc_gadget_start, + .udc_stop = ci_udc_gadget_stop, +#endif };static const struct usb_ep_ops ci_ep_ops = {@@ -927,7 +938,7 @@ void udc_irq(void) } } -int dm_usb_gadget_handle_interrupts (struct udevice *dev) +static int ci_udc_handle_interrupts (struct udevice *dev) {struct ci_udc *udc = (struct ci_udc *)controller.ctrl->hcor;u32 value;@@ -1072,6 +1083,71 @@ static int ci_udc_probe(void)return 0 ; } +#if CONFIG_IS_ENABLED (DM_USB_GADGET ) +static int ci_udc_generic_probe (struct udevice *dev) +{ +int ret; +#if CONFIG_IS_ENABLED (DM_USB ) + ret =usb_setup_ehci_gadget (&controller.ctrl); +#else + ret =usb_lowlevel_init (0 ,USB_INIT_DEVICE , (void **)&controller.ctrl); +#endif
...
drivers/usb/gadget/ci_udc.c static int ci_udc_probe(void) · line 1114
Quoted 11 lines
[...]
drivers/usb/gadget/ci_udc.c +10
-0+static int ci_udc_generic_remove (struct udevice *dev) +{ +usb_del_gadget_udc (&controller.gadget); + +if (IS_ENABLED (CONFIG_DM_USB )) { +usb_remove_ehci_gadget (&controller.ctrl); + }else { +usb_lowlevel_stop (0 ); + controller.ctrl =NULL ; + }
This style is nice for compile testing. But in the probe() function above you're still using the #if/#else pre-processor style. Can it use if (IS_ENABLED(...)) too?
if (IS_ENABLED(CONFIG_DM_USB)) ret = usb_setup_ehci_gadget(&controller.ctrl); else ret = usb_lowlevel_init(0, USB_INIT_DEVICE, (void **)&controller.ctrl); if (ret) return ret;
This seems to compile at least.
If yes, can you make the same cleanup for the old !DM_USB_GADGET case, so the two code paths are consistent?
Quoted 24 lines
drivers/usb/gadget/ci_udc.c +24
-0+ +return 0 ; +} + +static const struct usb_gadget_generic_ops ci_udc_generic_ops = { + .handle_interrupts = ci_udc_handle_interrupts, +}; + +U_BOOT_DRIVER (ci_udc_generic) = { + .name ="ci-udc" , + .id =UCLASS_USB_GADGET_GENERIC , + .ops = &ci_udc_generic_ops, + .probe = ci_udc_generic_probe, + .remove = ci_udc_generic_remove, +}; + +static int ci_udc_gadget_start (struct usb_gadget *g, +struct usb_gadget_driver *driver) +{ + controller.driver = driver; +return 0 ; +} + +static int ci_udc_gadget_stop (struct usb_gadget *g)
drivers/usb/gadget/ci_udc.c static int ci_udc_probe(void) · line 1148
Quoted 10 lines
drivers/usb/gadget/ci_udc.c +10
-0+{ + controller.driver =NULL ; +udc_disconnect (); + +ci_ep_free_request (&controller.ep[0 ].ep, &controller.ep0_req->req); +free (controller.items_mem); +free (controller.epts); + +return 0 ; +}
I wonder if you could just define the start and stop function outside the #if blocks and call them from usb_gadget_unregister_driver() and usb_gadget_register_driver(). This would avoid duplicating the code, reducing the risk that someone forgets to update one of those when making changes.
The same could be also said for probe()/remove(), i.e. moving the
if (IS_ENABLED(CONFIG_DM_USB)) {
usb_remove_ehci_gadget(&controller.ctrl);
} else {
usb_lowlevel_stop(0);
controller.ctrl = NULL;
}block to a separate function and calling that from both variants. Not sure if that would also be worth it?
Thanks,
Stephan
Re: [PATCH 1/3] usb: udc: ci: support USB gadget driver model
Heya Stephan,
Quoted 9 lines · Stephan Gerhold
Quoted 8 lines · Sam Day
When
CONFIG_DM_USB_GADGETis enabled, aUCLASS_USB_GADGET_GENERICdriver will be defined that wraps the ChipIdea UDC operations. The (dm_)?usb_gadget_.* symbols will no longer be defined (as these are now handled by the UDC uclass).If
CONFIG_DM_USB_GADGETis not enabled, this driver behaves as it previously did.
Quoted 8 lines
Quoted 5 lines
This new driver does not declare any compatibles of its own. It requires a glue driver to bind it. The
ehci_msmdriver will be updated in the following commit to do exactly that.Signed-off-by Sam Day <[email protected]>Thanks a lot for working on this. Seems to work without problems on my dragonboard410c. Just some minor nits below to reduce code duplication.
\0/ Thanks for the review and testing!
Quoted 61 lines
Quoted 58 lines
--- drivers/usb/gadget/ci_udc.c | 84 ++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 83 insertions(+), 1 deletion(-)drivers/usb/gadget/ci_udc.c +21
-1@@ -10,6 +10,7 @@#include <command.h> #include <config.h> #include <cpu_func.h> +#include <dm.h> #include <net.h> #include <malloc.h> #include <wait_bit.h> @@ -94,8 +95,18 @@ static struct usb_request * ci_ep_alloc_request(struct usb_ep *ep, unsigned int gfp_flags);static void ci_ep_free_request (struct usb_ep *ep,struct usb_request *_req); +#if CONFIG_IS_ENABLED (DM_USB_GADGET ) +static int ci_udc_gadget_start (struct usb_gadget *g, +struct usb_gadget_driver *driver); +static int ci_udc_gadget_stop (struct usb_gadget *g); +#endif +static const struct usb_gadget_ops ci_udc_ops = { .pullup = ci_pullup, +#if CONFIG_IS_ENABLED(DM_USB_GADGET) + .udc_start = ci_udc_gadget_start, + .udc_stop = ci_udc_gadget_stop, +#endif };static const struct usb_ep_ops ci_ep_ops = {@@ -927,7 +938,7 @@ void udc_irq(void) } } -int dm_usb_gadget_handle_interrupts (struct udevice *dev) +static int ci_udc_handle_interrupts (struct udevice *dev) {struct ci_udc *udc = (struct ci_udc *)controller.ctrl->hcor;u32 value;@@ -1072,6 +1083,71 @@ static int ci_udc_probe(void)return 0 ; } +#if CONFIG_IS_ENABLED (DM_USB_GADGET ) +static int ci_udc_generic_probe (struct udevice *dev) +{ +int ret; +#if CONFIG_IS_ENABLED (DM_USB ) + ret =usb_setup_ehci_gadget (&controller.ctrl); +#else + ret =usb_lowlevel_init (0 ,USB_INIT_DEVICE , (void **)&controller.ctrl); +#endif ...
Quoted 15 lines
drivers/usb/gadget/ci_udc.c static int ci_udc_probe(void) · line 1114
Quoted 11 lines
[...]
drivers/usb/gadget/ci_udc.c +10
-0+static int ci_udc_generic_remove (struct udevice *dev) +{ +usb_del_gadget_udc (&controller.gadget); + +if (IS_ENABLED (CONFIG_DM_USB )) { +usb_remove_ehci_gadget (&controller.ctrl); + }else { +usb_lowlevel_stop (0 ); + controller.ctrl =NULL ; + }This style is nice for compile testing. But in the
probe()function above you're still using the #if/#else pre-processor style. Can it use if (IS_ENABLED(...)) too?
Ah, I had converted a few of these when checkpatch reprimanded me. Guess I missed this one - oops!
Quoted 8 lines
if (IS_ENABLED(CONFIG_DM_USB)) ret = usb_setup_ehci_gadget(&controller.ctrl); else ret = usb_lowlevel_init(0, USB_INIT_DEVICE, (void **)&controller.ctrl); if (ret) return ret;
Quoted 4 lines
This seems to compile at least.
If yes, can you make the same cleanup for the old !DM_USB_GADGET case, so the two code paths are consistent?
Thanks, I've done this in v2.
Quoted 33 lines
Quoted 33 lines
drivers/usb/gadget/ci_udc.c +32
-0+ +return 0 ; +} + +static const struct usb_gadget_generic_ops ci_udc_generic_ops = { + .handle_interrupts = ci_udc_handle_interrupts, +}; + +U_BOOT_DRIVER (ci_udc_generic) = { + .name ="ci-udc" , + .id =UCLASS_USB_GADGET_GENERIC , + .ops = &ci_udc_generic_ops, + .probe = ci_udc_generic_probe, + .remove = ci_udc_generic_remove, +}; + +static int ci_udc_gadget_start (struct usb_gadget *g, +struct usb_gadget_driver *driver) +{ + controller.driver = driver; +return 0 ; +} + +static int ci_udc_gadget_stop (struct usb_gadget *g) +{ + controller.driver =NULL ; +udc_disconnect (); + +ci_ep_free_request (&controller.ep[0 ].ep, &controller.ep0_req->req); +free (controller.items_mem); +free (controller.epts); +
Quoted 8 lines
drivers/usb/gadget/ci_udc.c
Quoted 2 lines
drivers/usb/gadget/ci_udc.c +2
-0+return 0 ; +}I wonder if you could just define the start and stop function outside the #if blocks and call them from
usb_gadget_unregister_driver()andusb_gadget_register_driver(). This would avoid duplicating the code, reducing the risk that someone forgets to update one of those when making changes.
So, not quite unfortunately. In the case of ci_udc_gadget_stop(), the controller.driver = NULL happening before calling into udc_disconnect() is important: the generic UDC uclass code has already called driver->disconnect() and calling it again is a Very Bad Thing to do. So we can't just delegate usb_gadget_unregister_driver to ci_udc_gadget_stop outright.
In v2 I've tried to unify the codepaths as much as possible though, both to avoid duplication and the risks of future patches making incomplete changes.
Quoted 10 lines
The same could be also said for probe()/remove(), i.e. moving the
if (IS_ENABLED(CONFIG_DM_USB)) { usb_remove_ehci_gadget(&controller.ctrl); } else { usb_lowlevel_stop(0); controller.ctrl = NULL; }
Quoted 2 lines
block to a separate function and calling that from both variants. Not sure if that would also be worth it?
Good call, these ones are less problematic, and I've done that in v2.
Rock on \m/,
-Sam
Quoted 3 lines
Thanks,
Stephan
Re: [PATCH 1/3] usb: udc: ci: support USB gadget driver model
Quoted 181 lines · Sam Day
Heya Stephan,
Quoted 9 lines · Stephan Gerhold
Quoted 8 lines · Sam Day
When
CONFIG_DM_USB_GADGETis enabled, aUCLASS_USB_GADGET_GENERICdriver will be defined that wraps the ChipIdea UDC operations. The (dm_)?usb_gadget_.* symbols will no longer be defined (as these are now handled by the UDC uclass).If
CONFIG_DM_USB_GADGETis not enabled, this driver behaves as it previously did.Quoted 8 lines
Quoted 5 lines
This new driver does not declare any compatibles of its own. It requires a glue driver to bind it. The
ehci_msmdriver will be updated in the following commit to do exactly that.Signed-off-by Sam Day <me at samcday.com>Thanks a lot for working on this. Seems to work without problems on my dragonboard410c. Just some minor nits below to reduce code duplication.
\0/ Thanks for the review and testing!
Quoted 61 lines
Quoted 58 lines
--- drivers/usb/gadget/ci_udc.c | 84 ++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 83 insertions(+), 1 deletion(-)drivers/usb/gadget/ci_udc.c +21
-1@@ -10,6 +10,7 @@#include <command.h> #include <config.h> #include <cpu_func.h> +#include <dm.h> #include <net.h> #include <malloc.h> #include <wait_bit.h> @@ -94,8 +95,18 @@ static struct usb_request * ci_ep_alloc_request(struct usb_ep *ep, unsigned int gfp_flags);static void ci_ep_free_request (struct usb_ep *ep,struct usb_request *_req); +#if CONFIG_IS_ENABLED (DM_USB_GADGET ) +static int ci_udc_gadget_start (struct usb_gadget *g, +struct usb_gadget_driver *driver); +static int ci_udc_gadget_stop (struct usb_gadget *g); +#endif +static const struct usb_gadget_ops ci_udc_ops = { .pullup = ci_pullup, +#if CONFIG_IS_ENABLED(DM_USB_GADGET) + .udc_start = ci_udc_gadget_start, + .udc_stop = ci_udc_gadget_stop, +#endif };static const struct usb_ep_ops ci_ep_ops = {@@ -927,7 +938,7 @@ void udc_irq(void) } } -int dm_usb_gadget_handle_interrupts (struct udevice *dev) +static int ci_udc_handle_interrupts (struct udevice *dev) {struct ci_udc *udc = (struct ci_udc *)controller.ctrl->hcor;u32 value;@@ -1072,6 +1083,71 @@ static int ci_udc_probe(void)return 0 ; } +#if CONFIG_IS_ENABLED (DM_USB_GADGET ) +static int ci_udc_generic_probe (struct udevice *dev) +{ +int ret; +#if CONFIG_IS_ENABLED (DM_USB ) + ret =usb_setup_ehci_gadget (&controller.ctrl); +#else + ret =usb_lowlevel_init (0 ,USB_INIT_DEVICE , (void **)&controller.ctrl); +#endif ...
Quoted 15 lines
drivers/usb/gadget/ci_udc.c static int ci_udc_probe(void) · line 1114
Quoted 11 lines
[...]
drivers/usb/gadget/ci_udc.c +10
-0+static int ci_udc_generic_remove (struct udevice *dev) +{ +usb_del_gadget_udc (&controller.gadget); + +if (IS_ENABLED (CONFIG_DM_USB )) { +usb_remove_ehci_gadget (&controller.ctrl); + }else { +usb_lowlevel_stop (0 ); + controller.ctrl =NULL ; + }This style is nice for compile testing. But in the
probe()function above you're still using the #if/#else pre-processor style. Can it use if (IS_ENABLED(...)) too?Ah, I had converted a few of these when checkpatch reprimanded me. Guess I missed this one - oops!
Quoted 8 lines
if (IS_ENABLED(CONFIG_DM_USB)) ret = usb_setup_ehci_gadget(&controller.ctrl); else ret = usb_lowlevel_init(0, USB_INIT_DEVICE, (void **)&controller.ctrl); if (ret) return ret;Quoted 4 lines
This seems to compile at least.
If yes, can you make the same cleanup for the old !DM_USB_GADGET case, so the two code paths are consistent?
Thanks, I've done this in v2.
Quoted 33 lines
Quoted 33 lines
drivers/usb/gadget/ci_udc.c +32
-0+ +return 0 ; +} + +static const struct usb_gadget_generic_ops ci_udc_generic_ops = { + .handle_interrupts = ci_udc_handle_interrupts, +}; + +U_BOOT_DRIVER (ci_udc_generic) = { + .name ="ci-udc" , + .id =UCLASS_USB_GADGET_GENERIC , + .ops = &ci_udc_generic_ops, + .probe = ci_udc_generic_probe, + .remove = ci_udc_generic_remove, +}; + +static int ci_udc_gadget_start (struct usb_gadget *g, +struct usb_gadget_driver *driver) +{ + controller.driver = driver; +return 0 ; +} + +static int ci_udc_gadget_stop (struct usb_gadget *g) +{ + controller.driver =NULL ; +udc_disconnect (); + +ci_ep_free_request (&controller.ep[0 ].ep, &controller.ep0_req->req); +free (controller.items_mem); +free (controller.epts); +Quoted 8 lines
drivers/usb/gadget/ci_udc.c
Quoted 2 lines
drivers/usb/gadget/ci_udc.c +2
-0+return 0 ; +}I wonder if you could just define the start and stop function outside the #if blocks and call them from
usb_gadget_unregister_driver()andusb_gadget_register_driver(). This would avoid duplicating the code, reducing the risk that someone forgets to update one of those when making changes.So, not quite unfortunately. In the case of
ci_udc_gadget_stop(), the controller.driver = NULL happening before calling intoudc_disconnect()is important: the generic UDC uclass code has already calleddriver->disconnect()and calling it again is a Very Bad Thing to do. So we can't just delegateusb_gadget_unregister_drivertoci_udc_gadget_stopoutright.In v2 I've tried to unify the codepaths as much as possible though, both to avoid duplication and the risks of future patches making incomplete changes.
Quoted 10 lines
The same could be also said for probe()/remove(), i.e. moving the
if (IS_ENABLED(CONFIG_DM_USB)) { usb_remove_ehci_gadget(&controller.ctrl); } else { usb_lowlevel_stop(0); controller.ctrl = NULL; }
Quoted 4 lines
Quoted 2 lines
block to a separate function and calling that from both variants. Not sure if that would also be worth it?
Good call, these ones are less problematic, and I've done that in v2.
Hello Sam,
Are you going to send v2 soon? I am just asking as I had something similar in the pipeline.
Regrads,
Wojtek
Quoted 9 lines
Rock on \m/,
-SamQuoted 3 lines
Thanks,
Stephan
PATCH 2/3 usb: host: ehci-msm: Register ChipIdea UDC from glue wrapper
In reply to Sam DayWhen CONFIG_DM_USB_GADGET is enabled, the CI UDC driver needs to be explicitly bound. So we do this from the newly introduced glue driver.
--- drivers/usb/host/ehci-msm.c | 7 +++++++ 1 file changed, 7 insertions(+)
drivers/usb/host/ehci-msm.c +7 -0
@@ -161,6 +161,13 @@ static int qcom_ci_hdrc_bind(struct udevice *dev)if (ret)return ret; +if (IS_ENABLED (CONFIG_DM_USB_GADGET ) &&IS_ENABLED (CONFIG_CI_UDC )) { + ret =device_bind_driver_to_node (dev,"ci-udc" ,"ci-udc" , +dev_ofnode (dev),NULL ); +if (ret) +return ret; + } +if (!ofnode_valid (ulpi_node))return 0 ;
Signature · 1 line
2.49.0
Re: [PATCH 2/3] usb: host: ehci-msm: Register ChipIdea UDC from glue wrapper
Quoted 13 lines · Sam Day
When
CONFIG_DM_USB_GADGETis enabled, the CI UDC driver needs to be explicitly bound. So we do this from the newly introduced glue driver.Signed-off-by Sam Day <[email protected]>--- drivers/usb/host/ehci-msm.c | 7 +++++++ 1 file changed, 7 insertions(+)drivers/usb/host/ehci-msm.c +0
-0
drivers/usb/host/ehci-msm.c static int qcom_ci_hdrc_bind(struct udevice *dev) · line 166
Quoted 6 lines
drivers/usb/host/ehci-msm.c +3
-0@@ -161,6 +161,13 @@ static int qcom_ci_hdrc_bind(struct udevice *dev)if (ret)return ret; +if (IS_ENABLED (CONFIG_DM_USB_GADGET ) &&IS_ENABLED (CONFIG_CI_UDC )) { + ret =device_bind_driver_to_node (dev,"ci-udc" ,"ci-udc" , +dev_ofnode (dev),NULL );
Nitpick: Indentation looks off here (we usually align with the open parenthesis (
Thanks,
Stephan
PATCH 3/3 qcom_defconfig: Enable MSM8916 USB PHY + ChipIdea UDC
In reply to Sam DayNow that the ChipIdea UDC driver supports USB Gadget driver model, we can enable it alongside the dwc3 generic driver.
--- configs/qcom_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)
configs/qcom_defconfig +6 -0
@@ -45,6 +45,7 @@ CONFIG_OF_UPSTREAM_BUILD_VENDOR=y CONFIG_USE_DEFAULT_ENV_FILE=y CONFIG_DEFAULT_ENV_FILE="board/qualcomm/default.env" CONFIG_BUTTON_QCOM_PMIC=y +CONFIG_CI_UDC=y CONFIG_CLK=y CONFIG_CLK_STUB=y CONFIG_CLK_QCOM_APQ8016=y
@@ -121,6 +122,7 @@ CONFIG_RNG_MSM=y CONFIG_SCSI=y CONFIG_MSM_SERIAL=y CONFIG_MSM_GENI_SERIAL=y +CONFIG_MSM8916_USB_PHY=y CONFIG_SOC_QCOM=y CONFIG_QCOM_COMMAND_DB=y CONFIG_QCOM_RPMH=y
@@ -133,6 +135,10 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_DWC3=y CONFIG_USB_DWC3_GENERIC=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_MSM=y +CONFIG_USB_ULPI=y +CONFIG_USB_ULPI_VIEWPORT=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_USB_FUNCTION_MASS_STORAGE=y
Signature · 1 line
2.49.0
Re: [PATCH 3/3] qcom_defconfig: Enable MSM8916 USB PHY + ChipIdea UDC
Quoted 29 lines · Sam Day
Now that the ChipIdea UDC driver supports USB Gadget driver model, we can enable it alongside the dwc3 generic driver.
Signed-off-by Sam Day <[email protected]>--- configs/qcom_defconfig | 6 ++++++ 1 file changed, 6 insertions(+)configs/qcom_defconfig +2
-0@@ -45,6 +45,7 @@ CONFIG_OF_UPSTREAM_BUILD_VENDOR=y CONFIG_USE_DEFAULT_ENV_FILE=y CONFIG_DEFAULT_ENV_FILE="board/qualcomm/default.env" CONFIG_BUTTON_QCOM_PMIC=y +CONFIG_CI_UDC=y CONFIG_CLK=y CONFIG_CLK_STUB=y CONFIG_CLK_QCOM_APQ8016=y@@ -121,6 +122,7 @@ CONFIG_RNG_MSM=y CONFIG_SCSI=y CONFIG_MSM_SERIAL=y CONFIG_MSM_GENI_SERIAL=y +CONFIG_MSM8916_USB_PHY=y CONFIG_SOC_QCOM=y CONFIG_QCOM_COMMAND_DB=y CONFIG_QCOM_RPMH=y
configs/qcom_defconfig CONFIG_USB_XHCI_HCD=y · line 144
Quoted 10 lines
configs/qcom_defconfig +4
-0@@ -133,6 +135,10 @@ CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_DWC3=y CONFIG_USB_DWC3_GENERIC=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_MSM=y +CONFIG_USB_ULPI=y +CONFIG_USB_ULPI_VIEWPORT=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_USB_FUNCTION_MASS_STORAGE=y
Please run "make savedefconfig" "cp defconfig configs/qcom_defconfig".
Defconfigs are not alphabetically ordered, they are ordered based on the definitions in the Kconfig files. And some of the options (e.g. CONFIG_MSM8916_USB_PHY) will disappear because they're already selected by other options. :-)
Thanks,
Stephan