i2c: designware: Add SMBus Quick Command support
Subsystems (3)
PATCH 1/1 i2c: designware: Add SMBus Quick Command support
From: Tan En De <[email protected]>
Add support for SMBus Quick Read and Quick Write commands.
Signed-off-by Tan En De <[email protected]>
--- drivers/i2c/busses/i2c-designware-core.h | 4 ++++ drivers/i2c/busses/i2c-designware-master.c | 18 +++++++++++++++++- 2 files changed, 21 insertions(+), 1 deletion(-)
drivers/i2c/busses/i2c-designware-core.h +4 -0
@@ -40,6 +40,8 @@#define DW_IC_DATA_CMD_DAT GENMASK(7, 0)#define DW_IC_DATA_CMD_FIRST_DATA_BYTE BIT(11) +#define DW_IC_DATA_CMD_STOP BIT(9) +#define DW_IC_DATA_CMD_CMD BIT(8)/* * Registers offset
@@ -123,7 +125,9 @@#define DW_IC_ERR_TX_ABRT 0x1 +#define DW_IC_TAR_SMBUS_QUICK_CMD BIT(16)#define DW_IC_TAR_10BITADDR_MASTER BIT(12) +#define DW_IC_TAR_SPECIAL BIT(11)#define DW_IC_COMP_PARAM_1_SPEED_MODE_HIGH (BIT(2) | BIT(3))#define DW_IC_COMP_PARAM_1_SPEED_MODE_MASK GENMASK(3, 2)
drivers/i2c/busses/i2c-designware-master.c +17 -1
@@ -268,6 +268,10 @@ static void i2c_dw_xfer_init(struct dw_i2c_dev *dev)regmap_update_bits (dev->map,DW_IC_CON ,DW_IC_CON_10BITADDR_MASTER , ic_con); +/* i2c-core-smbus.c: Only I2C_SMBUS_QUICK has msg[0].len = 0 */ +if (dev->msgs[0 ].len ==0 ) + ic_tar |=DW_IC_TAR_SMBUS_QUICK_CMD |DW_IC_TAR_SPECIAL ; +/* * Set the slave (target) address and enable 10-bit addressing mode * if applicable.
@@ -474,6 +478,16 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev)regmap_read (dev->map,DW_IC_RXFLR , &flr); rx_limit = dev->rx_fifo_depth - flr; +/* i2c-core-smbus.c: Only I2C_SMBUS_QUICK has msg[0].len = 0 */ +if (buf_len ==0 && tx_limit >0 && rx_limit >0 ) { +regmap_write ( + dev->map,DW_IC_DATA_CMD , + *buf |DW_IC_DATA_CMD_STOP | + ((msgs[dev->msg_write_idx].flags &I2C_M_RD ) ? +DW_IC_DATA_CMD_CMD :0 ) + ); + } +while (buf_len >0 && tx_limit >0 && rx_limit >0 ) {u32 cmd =0 ;
@@ -919,7 +933,9 @@ void i2c_dw_configure_master(struct dw_i2c_dev *dev) {struct i2c_timings *t = &dev->timings; - dev->functionality =I2C_FUNC_10BIT_ADDR |DW_IC_DEFAULT_FUNCTIONALITY ; + dev->functionality =I2C_FUNC_10BIT_ADDR | +I2C_FUNC_SMBUS_QUICK | +DW_IC_DEFAULT_FUNCTIONALITY ; dev->master_cfg =DW_IC_CON_MASTER |DW_IC_CON_SLAVE_DISABLE |DW_IC_CON_RESTART_EN ;
Signature · 1 line
2.34.1