Skip to contentSkip to conversation

arm64: dts: imx8mm-beacon: Fix RTC capacitive load

PATCH Applied Adam Ford 3 participants 19 messages Apr 16, 2025 – Apr 25, 2025

Subsystems (2)
lore
Share & tools
lore

Adam Ford

author
#0 lore raw

PATCH v2 1/10 arm64: dts: imx8mm-beacon: Fix RTC capacitive load

Although not noticeable when used every day, the RTC appears to drift when left to sit over time. This is due to the capacitive load not being properly set. Fix RTC drift by correcting the capacitive load setting from 7000 to 12500, which matches the actual hardware configuration.

Fixes 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")

---
V2: Change commit message, no active changes.

 arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi +1 -0
index 62ed64663f49..9ba0cb89fa24 100644
@@ -233,6 +233,7 @@ eeprom@50 {
 	rtc: rtc@51 {
 		compatible = "nxp,pcf85263";
 		reg = <0x51>;
+		quartz-load-femtofarads = <12500>;
 	};
 };
 
Signature · 1 line
2.48.1
author
#1 lore raw

PATCH v2 2/10 arm64: dts: imx8mn-beacon: Fix RTC capacitive load

Although not noticeable when used every day, the RTC appears to drift when left to sit over time. This is due to the capacitive load not being properly set. Fix RTC drift by correcting the capacitive load setting from 7000 to 12500, which matches the actual hardware configuration.

Fixes 36ca3c8ccb53 ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")

---
V2: Change commit message, no active changes.

 arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi +1 -0
index 2a64115eebf1..bb11590473a4 100644
@@ -242,6 +242,7 @@ eeprom@50 {
 	rtc: rtc@51 {
 		compatible = "nxp,pcf85263";
 		reg = <0x51>;
+		quartz-load-femtofarads = <12500>;
 	};
 };
 
Signature · 1 line
2.48.1
maintainer Reviewed-by on v2 2/10
#2 lore raw

Re: [PATCH V2 02/10] arm64: dts: imx8mn-beacon: Fix RTC capacitive load

Quoted 8 lines · Adam Ford

Although not noticeable when used every day, the RTC appears to drift when left to sit over time. This is due to the capacitive load not being properly set. Fix RTC drift by correcting the capacitive load setting from 7000 to 12500, which matches the actual hardware configuration.

Fixes 36ca3c8ccb53 ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")

---

Quoted 20 lines

V2: Change commit message, no active changes.

 arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi +1 -1
index 2a64115eebf1..bb11590473a4 100644
@@ -242,6 +242,7 @@ eeprom@50 {
 	rtc: rtc@51 {
 		compatible = "nxp,pcf85263";
 		reg = <0x51>;
+		quartz-load-femtofarads = <12500>;
 	};
 };
 
--

2.48.1

author
#3 lore raw

PATCH v2 3/10 arm64: dts: imx8mp-beacon: Fix RTC capacitive load

In reply to Adam Ford

Although not noticeable when used every day, the RTC appears to drift when left to sit over time. This is due to the capacitive load not being properly set. Fix RTC drift by correcting the capacitive load setting from 7000 to 12500, which matches the actual hardware configuration.

Fixes 25a5ccdce767 ("arm64: dts: freescale: Introduce imx8mp-beacon-kit")

---
V2: Change commit message, no active changes.

 arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi +1 -0
index 15f7ab58db36..88561df70d03 100644
@@ -257,6 +257,7 @@ eeprom@50 {
 	rtc: rtc@51 {
 		compatible = "nxp,pcf85263";
 		reg = <0x51>;
+		quartz-load-femtofarads = <12500>;
 	};
 };
 
Signature · 1 line
2.48.1
maintainer Reviewed-by on v2 3/10
#4 lore raw

Re: [PATCH V2 03/10] arm64: dts: imx8mp-beacon: Fix RTC capacitive load

Quoted 8 lines · Adam Ford

Although not noticeable when used every day, the RTC appears to drift when left to sit over time. This is due to the capacitive load not being properly set. Fix RTC drift by correcting the capacitive load setting from 7000 to 12500, which matches the actual hardware configuration.

Fixes 25a5ccdce767 ("arm64: dts: freescale: Introduce imx8mp-beacon-kit")

---

Quoted 20 lines

V2: Change commit message, no active changes.

 arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi +1 -1
index 15f7ab58db36..88561df70d03 100644
@@ -257,6 +257,7 @@ eeprom@50 {
 	rtc: rtc@51 {
 		compatible = "nxp,pcf85263";
 		reg = <0x51>;
+		quartz-load-femtofarads = <12500>;
 	};
 };
 
--

2.48.1

author
#5 lore raw

PATCH v2 4/10 arm64: dts: imx8mm-beacon: Set SAI5 MCLK direction to output for HDMI audio

In reply to Adam Ford

The HDMI bridge chip fails to generate an audio source due to the SAI5 master clock (MCLK) direction not being set to output. This prevents proper clocking of the HDMI audio interface.

Add the fsl,sai-mclk-direction-output property to the SAI5 node to ensure the MCLK is driven by the SoC, resolving the HDMI sound issue.

Fixes 8ad7d14d99f3 ("arm64: dts: imx8mm-beacon: Add HDMI video with sound")

---
V2: Change commit message, no active changes.

 arch/arm64/boot/dts/freescale/imx8mm-beacon-kit.dts | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/freescale/imx8mm-beacon-kit.dts +1 -0
index 97ff1ddd6318..734a75198f06 100644
@@ -124,6 +124,7 @@ &sai5 {
 	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
 	assigned-clock-rates = <24576000>;
 	#sound-dai-cells = <0>;
+	fsl,sai-mclk-direction-output;
 	status = "okay";
 };
 
Signature · 1 line
2.48.1
maintainer Reviewed-by on v2 4/10
#6 lore raw

Re: [PATCH V2 04/10] arm64: dts: imx8mm-beacon: Set SAI5 MCLK direction to output for HDMI audio

Quoted 10 lines · Adam Ford

The HDMI bridge chip fails to generate an audio source due to the SAI5 master clock (MCLK) direction not being set to output. This prevents proper clocking of the HDMI audio interface.

Add the fsl,sai-mclk-direction-output property to the SAI5 node to ensure the MCLK is driven by the SoC, resolving the HDMI sound issue.

Fixes 8ad7d14d99f3 ("arm64: dts: imx8mm-beacon: Add HDMI video with sound")

---

Quoted 20 lines

V2: Change commit message, no active changes.

 arch/arm64/boot/dts/freescale/imx8mm-beacon-kit.dts | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/freescale/imx8mm-beacon-kit.dts +1 -1
index 97ff1ddd6318..734a75198f06 100644
@@ -124,6 +124,7 @@ &sai5 {
 	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
 	assigned-clock-rates = <24576000>;
 	#sound-dai-cells = <0>;
+	fsl,sai-mclk-direction-output;
 	status = "okay";
 };
 
--

2.48.1

author
#7 lore raw

PATCH v2 5/10 arm64: dts: imx8mn-beacon: Set SAI5 MCLK direction to output for HDMI audio

In reply to Adam Ford

The HDMI bridge chip fails to generate an audio source due to the SAI5 master clock (MCLK) direction not being set to output. This prevents proper clocking of the HDMI audio interface.

Add the fsl,sai-mclk-direction-output property to the SAI5 node to ensure the MCLK is driven by the SoC, resolving the HDMI sound issue.

Fixes 1d6880ceef43 ("arm64: dts: imx8mn-beacon: Add HDMI video with sound")

---
V2: Change commit message, no active changes.

 arch/arm64/boot/dts/freescale/imx8mn-beacon-kit.dts | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/freescale/imx8mn-beacon-kit.dts +1 -0
index 1df5ceb11387..37fc5ed98d7f 100644
@@ -124,6 +124,7 @@ &sai5 {
 	assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>;
 	assigned-clock-rates = <24576000>;
 	#sound-dai-cells = <0>;
+	fsl,sai-mclk-direction-output;
 	status = "okay";
 };
 
Signature · 1 line
2.48.1
maintainer Reviewed-by on v2 5/10
#8 lore raw

Re: [PATCH V2 05/10] arm64: dts: imx8mn-beacon: Set SAI5 MCLK direction to output for HDMI audio

Quoted 11 lines · Adam Ford

The HDMI bridge chip fails to generate an audio source due to the SAI5 master clock (MCLK) direction not being set to output. This prevents proper clocking of the HDMI audio interface.

Add the fsl,sai-mclk-direction-output property to the SAI5 node to ensure the MCLK is driven by the SoC, resolving the HDMI sound issue.

Fixes 1d6880ceef43 ("arm64: dts: imx8mn-beacon: Add HDMI video with sound")

---
V2: Change commit message, no active changes.

Quoted 19 lines
 arch/arm64/boot/dts/freescale/imx8mn-beacon-kit.dts | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/freescale/imx8mn-beacon-kit.dts +1 -1
index 1df5ceb11387..37fc5ed98d7f 100644
@@ -124,6 +124,7 @@ &sai5 {
 	assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>;
 	assigned-clock-rates = <24576000>;
 	#sound-dai-cells = <0>;
+	fsl,sai-mclk-direction-output;
 	status = "okay";
 };
 
--

2.48.1

author
#9 lore raw

PATCH v2 6/10 arm64: dts: imx8mm-beacon: Configure Ethernet PHY reset and GPIO IRQ

In reply to Adam Ford

The Ethernet PHY setup currently assumes that the bootloader will take the PHY out of reset, but this behavior is not guaranteed across all bootloaders. Add the reset GPIO to ensure the kernel can properly control the PHY reset line.

Also configure the PHY IRQ GPIO to enable interrupt-driven link status reporting, instead of relying on polling.

This ensures more reliable Ethernet initialization and improves PHY event handling.

---
V2: Update commit message. No active changes.

 arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi +4 -0
index 9ba0cb89fa24..ed7a1be4a1a6 100644
@@ -78,6 +78,9 @@ mdio {
 		ethphy0: ethernet-phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
+			reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
 		};
 	};
 };
@@ -315,6 +318,7 @@ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x1f
 			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x91
 			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
 			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10             0x146
 			MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22	0x19
 		>;
 	};
Signature · 1 line
2.48.1
maintainer Reviewed-by on v2 6/10
#10 lore raw

Re: [PATCH V2 06/10] arm64: dts: imx8mm-beacon: Configure Ethernet PHY reset and GPIO IRQ

Quoted 5 lines · Adam Ford

The Ethernet PHY setup currently assumes that the bootloader will take the PHY out of reset, but this behavior is not guaranteed across all bootloaders. Add the reset GPIO to ensure the kernel can properly control the PHY reset line.

Quoted 7 lines

Also configure the PHY IRQ GPIO to enable interrupt-driven link status reporting, instead of relying on polling.

This ensures more reliable Ethernet initialization and improves PHY event handling.

Quoted 31 lines

---
V2: Update commit message. No active changes.

 arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi +4 -1
index 9ba0cb89fa24..ed7a1be4a1a6 100644
@@ -78,6 +78,9 @@ mdio {
 		ethphy0: ethernet-phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
+			reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
 		};
 	};
 };
@@ -315,6 +318,7 @@ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x1f
 			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x91
 			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
 			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10             0x146
 			MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22	0x19
 		>;
 	};
--

2.48.1

author
#11 lore raw

PATCH v2 7/10 arm64: dts: imx8mn-beacon: Configure Ethernet PHY reset and GPIO IRQ

In reply to Adam Ford

The Ethernet PHY setup currently assumes that the bootloader will take the PHY out of reset, but this behavior is not guaranteed across all bootloaders. Add the reset GPIO to ensure the kernel can properly control the PHY reset line.

Also configure the PHY IRQ GPIO to enable interrupt-driven link status reporting, instead of relying on polling.

This ensures more reliable Ethernet initialization and improves PHY event handling.

---
V2: Update commit message. No active changes.

 arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi +4 -0
index bb11590473a4..b3692b367a42 100644
@@ -88,6 +88,9 @@ mdio {
 		ethphy0: ethernet-phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
+			reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
 		};
 	};
 };
@@ -326,6 +329,7 @@ MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x1f
 			MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x91
 			MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
 			MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MN_IOMUXC_GPIO1_IO10_GPIO1_IO10             0x146
 			MX8MN_IOMUXC_SAI2_RXC_GPIO4_IO22	0x19
 		>;
 	};
Signature · 1 line
2.48.1
maintainer Reviewed-by on v2 7/10
#12 lore raw

Re: [PATCH V2 07/10] arm64: dts: imx8mn-beacon: Configure Ethernet PHY reset and GPIO IRQ

Quoted 5 lines · Adam Ford

The Ethernet PHY setup currently assumes that the bootloader will take the PHY out of reset, but this behavior is not guaranteed across all bootloaders. Add the reset GPIO to ensure the kernel can properly control the PHY reset line.

Quoted 8 lines

Also configure the PHY IRQ GPIO to enable interrupt-driven link status reporting, instead of relying on polling.

This ensures more reliable Ethernet initialization and improves PHY event handling.

---

Quoted 30 lines

V2: Update commit message. No active changes.

 arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi +4 -1
index bb11590473a4..b3692b367a42 100644
@@ -88,6 +88,9 @@ mdio {
 		ethphy0: ethernet-phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
+			reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
 		};
 	};
 };
@@ -326,6 +329,7 @@ MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x1f
 			MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x91
 			MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
 			MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MN_IOMUXC_GPIO1_IO10_GPIO1_IO10             0x146
 			MX8MN_IOMUXC_SAI2_RXC_GPIO4_IO22	0x19
 		>;
 	};
--

2.48.1

author
#13 lore raw

PATCH v2 8/10 arm64: dts: imx8mm-beacon: Enable RTC interrupt and wakeup-source

In reply to Adam Ford

Enable the interrupts and wakeup-source to allow the external RTC to be used as an alarm.

---
V2: Update commit message. Re-order node

 arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)
arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi +11 -0
index ed7a1be4a1a6..c7a8f2a6fe90 100644
@@ -236,7 +236,12 @@ eeprom@50 {
 	rtc: rtc@51 {
 		compatible = "nxp,pcf85263";
 		reg = <0x51>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
 		quartz-load-femtofarads = <12500>;
+		wakeup-source;
 	};
 };
 
@@ -354,6 +359,12 @@ MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x141
 		>;
 	};
 
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x146
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX	0x140
Signature · 1 line
2.48.1
maintainer Reviewed-by on v2 8/10
#14 lore raw

Re: [PATCH V2 08/10] arm64: dts: imx8mm-beacon: Enable RTC interrupt and wakeup-source

Quoted 4 lines · Adam Ford

Enable the interrupts and wakeup-source to allow the external RTC to be used as an alarm.

Quoted 39 lines

---
V2: Update commit message. Re-order node

 arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)
arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi +11 -1
index ed7a1be4a1a6..c7a8f2a6fe90 100644
@@ -236,7 +236,12 @@ eeprom@50 {
 	rtc: rtc@51 {
 		compatible = "nxp,pcf85263";
 		reg = <0x51>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
 		quartz-load-femtofarads = <12500>;
+		wakeup-source;
 	};
 };
 
@@ -354,6 +359,12 @@ MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x141
 		>;
 	};
 
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x146
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX	0x140
--

2.48.1

author
#15 lore raw

PATCH v2 9/10 arm64: dts: imx8mn-beacon: Enable RTC interrupt and wakeup-source

In reply to Adam Ford

Enable the interrupts and wakeup-source to allow the external RTC to be used as an alarm.

---
V2: Update commit message. No active changes

 arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi +11 -0
index b3692b367a42..987c14d3af9d 100644
@@ -245,7 +245,12 @@ eeprom@50 {
 	rtc: rtc@51 {
 		compatible = "nxp,pcf85263";
 		reg = <0x51>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
 		quartz-load-femtofarads = <12500>;
+		wakeup-source;
 	};
 };
 
@@ -365,6 +370,12 @@ MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x141
 		>;
 	};
 
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x146
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX	0x140
Signature · 1 line
2.48.1
maintainer Reviewed-by on v2 9/10
#16 lore raw

Re: [PATCH V2 09/10] arm64: dts: imx8mn-beacon: Enable RTC interrupt and wakeup-source

Quoted 5 lines · Adam Ford

Enable the interrupts and wakeup-source to allow the external RTC to be used as an alarm.

---

Quoted 38 lines

V2: Update commit message. No active changes

 arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi +11 -1
index b3692b367a42..987c14d3af9d 100644
@@ -245,7 +245,12 @@ eeprom@50 {
 	rtc: rtc@51 {
 		compatible = "nxp,pcf85263";
 		reg = <0x51>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
 		quartz-load-femtofarads = <12500>;
+		wakeup-source;
 	};
 };
 
@@ -365,6 +370,12 @@ MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x141
 		>;
 	};
 
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x146
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX	0x140
--

2.48.1

author
#17 lore raw

PATCH v2 10/10 arm64: dts: imx8mp-beacon: Enable RTC interrupt and wakeup-source

In reply to Adam Ford

Enable the interrupts and wakeup-source to allow the external RTC to be used as an alarm.

---
V2: New to series

 arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)
arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi +11 -0
index 88561df70d03..6a62cb32e22e 100644
@@ -257,7 +257,12 @@ eeprom@50 {
 	rtc: rtc@51 {
 		compatible = "nxp,pcf85263";
 		reg = <0x51>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
 		quartz-load-femtofarads = <12500>;
+		wakeup-source;
 	};
 };
 
@@ -382,6 +387,12 @@ MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06	0x40
 		>;
 	};
 
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO13__GPIO1_IO13	0x1d0
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX	0x140
Signature · 1 line
2.48.1
Applied
#18 lore raw
In reply to Adam Ford
Quoted 7 lines · Adam Ford

Although not noticeable when used every day, the RTC appears to drift when left to sit over time. This is due to the capacitive load not being properly set. Fix RTC drift by correcting the capacitive load setting from 7000 to 12500, which matches the actual hardware configuration.

Fixes 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")

Applied all, thanks!