bcache: reduce front IO latency during GC
v3 cover bcache: reduce front IO latency during GC
In performance benchmarks on disks with bcache using the Linux 6.6 kernel, we observe noticeable IO latency increase during btree garbage collection. The increase ranges from high tens to hundreds of milliseconds, depending on the size of the cache device. Further investigation reveals that it is the same issue reported in [1], where the large number of nodes processed in each incremental GC cycle causes the front IO latency.
Building upon the approach suggested in [1], this patch decomposes the incremental GC process into more but smaller cycles. In contrast to [1], this implementation adopts a simpler strategy by setting a lower limit of 10 nodes per cycle to reduce front IO delay and introducing a fixed 10ms sleep per cycle when front IO is in progress. Furthermore, when garbage collection statistics are available, the number of nodes processed per cycle is dynamically rescaled based on the average GC frequency to ensure GC completes well within the next subsequent scheduled interval.
Testing with a 750GB NVMe cache and 256KB bucket size using the following fio configuration demonstrates that our patch reduces front IO latency during GC without significantly increasing GC duration.
ioengine=libaio
direct=1
bs=4k
size=900G
iodepth=10
readwrite=randwrite
log_avg_msec=10
Before:
time-ms,latency-ns,,,
12170, 285016, 1, 0, 0
12183, 296581, 1, 0, 0
12207, 6542725, 1, 0, 0
12242, 24483604, 1, 0, 0
12250, 1895628, 1, 0, 0
12260, 284854, 1, 0, 0
12270, 275513, 1, 0, 0
/sys/block/bcache0/bcache/cache/internal/btree_gc_average_duration_ms:2880 /sys/block/bcache0/bcache/cache/internal/btree_gc_average_frequency_sec:133 /sys/block/bcache0/bcache/cache/internal/btree_gc_last_sec:121 /sys/block/bcache0/bcache/cache/internal/btree_gc_max_duration_ms:3456
After:
12690, 378494, 1, 0, 0
12700, 413934, 1, 0, 0
12710, 661217, 1, 0, 0
12727, 354510, 1, 0, 0
12730, 1100768, 1, 0, 0
12742, 382484, 1, 0, 0
12750, 532679, 1, 0, 0
12760, 572758, 1, 0, 0
12773, 283416, 1, 0, 0
/sys/block/bcache0/bcache/cache/internal/btree_gc_average_duration_ms:3619 /sys/block/bcache0/bcache/cache/internal/btree_gc_average_frequency_sec:58 /sys/block/bcache0/bcache/cache/internal/btree_gc_last_sec:23 /sys/block/bcache0/bcache/cache/internal/btree_gc_max_duration_ms:3866
[1] https://lore.kernel.org/all/[email protected]/
---
Changes in v3:
- Use 64-bit integer division macros to fix build error on i386 architecture.
Robert Pang (1):
bcache: process fewer btree nodes in incremental GC cycles
drivers/md/bcache/btree.c | 37 ++++++++++++++++++------------------- drivers/md/bcache/util.h | 7 +++++++ 2 files changed, 25 insertions(+), 19 deletions(-)
Signature · 1 line
2.49.0.777.g153de2bbd5-goog
PATCH v3 1/1 bcache: process fewer btree nodes in incremental GC cycles
Current incremental GC processes a minimum of 100 btree nodes per cycle, followed by a 100ms sleep. For NVMe cache devices, where the average node processing time is ~1ms, this leads to front-side I/O latency potentially reaching tens or hundreds of milliseconds during GC execution.
This commit resolves this latency issue by reducing the minimum node processing count per cycle to 10 and the inter-cycle sleep duration to 10ms. It also integrates a check of existing GC statistics to re-scale the number of nodes processed per sleep interval when needed, ensuring GC finishes well before the next GC is due.
--- drivers/md/bcache/btree.c | 37 ++++++++++++++++++------------------- drivers/md/bcache/util.h | 7 +++++++ 2 files changed, 25 insertions(+), 19 deletions(-)
drivers/md/bcache/btree.c +18 -19
@@ -90,9 +90,8 @@#define MAX_NEED_GC 64#define MAX_SAVE_PRIO 72 -#define MAX_GC_TIMES 100 -#define MIN_GC_NODES 100 -#define GC_SLEEP_MS 100 +#define GC_MIN_NODES 10 +#define GC_SLEEP_MS 10#define PTR_DIRTY_BIT (((uint64_t) 1 << 36))
@@ -1585,25 +1584,25 @@ static unsigned int btree_gc_count_keys(struct btree *b)static size_t btree_gc_min_nodes (struct cache_set *c) { -size_t min_nodes; +size_t min_nodes =GC_MIN_NODES ; +uint64_t gc_max_ms =time_stat_average (&c->btree_gc_time, frequency, ms) /2 ;/* -* Since incremental GC would stop 100ms when front -* side I/O comes, so when there are many btree nodes, -* if GC only processes constant (100) nodes each time, -* GC would last a long time, and the front side I/Os -* would run out of the buckets (since no new bucket -* can be allocated during GC), and be blocked again. -* So GC should not process constant nodes, but varied -* nodes according to the number of btree nodes, which -* realized by dividing GC into constant(100) times, -* so when there are many btree nodes, GC can process -* more nodes each time, otherwise, GC will process less -* nodes each time (but no less than MIN_GC_NODES) +* The incremental garbage collector operates by processing +* GC_MIN_NODES at a time, pausing for GC_SLEEP_MS between +* each interval. If historical garbage collection statistics +* (btree_gc_time) is available, the maximum allowable GC +* duration is set to half of this observed frequency. To +* prevent exceeding this maximum duration, the number of +* nodes processed in the current step may be increased if +* the projected completion time based on the current pace +* extends beyond the allowed limit. This ensures timely GC +* completion before the next GC is due. */ - min_nodes = c->gc_stats.nodes /MAX_GC_TIMES ; -if (min_nodes <MIN_GC_NODES ) - min_nodes =MIN_GC_NODES ; +if ((gc_max_ms >=GC_SLEEP_MS ) && + (GC_SLEEP_MS * (c->gc_stats.nodes / min_nodes)) > gc_max_ms) + min_nodes =div64_u64 (c->gc_stats.nodes, +div_u64 (gc_max_ms,GC_SLEEP_MS ));return min_nodes; }
drivers/md/bcache/util.h +7 -0
@@ -305,6 +305,13 @@ static inline unsigned int local_clock_us(void)#define NSEC_PER_ms NSEC_PER_MSEC#define NSEC_PER_sec NSEC_PER_SEC +/* +* time_stat_average - return the average duration/frequency stat of a time +* stats in the desired unit. +*/ +#define time_stat_average (stats, stat, units) \ + div_u64((stats)->average_ ## stat >> 8, NSEC_PER_ ## units) +#define __print_time_stat (stats, name, stat, units) \ sysfs_print(name ## _ ## stat ## _ ## units, \ div_u64((stats)->stat >> 8, NSEC_PER_ ## units))
Signature · 1 line
2.49.0.777.g153de2bbd5-goog