Skip to contentSkip to conversation

Update PHYTEC i.MX93 DTS

PATCH Applied Primoz Fiser 2 participants 17 messages Apr 22, 2025 – May 9, 2025

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v4 cover Update PHYTEC i.MX93 DTS

Update i.MX93 device-tree sources in mainline for phyCORE-i.MX93 SoM and phyBOARD-Segin-i.MX93 board with changes from the downstream kernel.

New SoM features:
- PMIC support
- EEPROM support
- enhanced eMMC support
- fix eMMC for ERR052021

New board features:
- RTC support
- CAN support
- USB support
- I2S audio support
- 2nd Ethernet (EQOS interface)
- enhanced SD-card support
- fix SD-card for ERR052021

Link to v3: https://lore.kernel.org/all/[email protected]/

Changes in v4:

Patch #1:
- no changes

Patch #2:
- no changes

Patch #3:
- fix commit message (s/pull-down/pull-up)

Patch #4:
- no changes

Patch #5:
- no changes

Patch #6:
- no changes

Patch #7:
- no changes

Patch #8:
- no changes

Patch #9:
- no changes

Patch #10:
- no changes

Patch #11:
- no changes

Patch #12:
- no changes

Patch #13:
- no changes

Patch #14:
- no changes

Patch #15:
- no changes

Primoz Fiser (15):
arm64: dts: freescale: imx93-phycore-som: Add PMIC support
arm64: dts: freescale: imx93-phycore-som: Add EEPROM support
arm64: dts: freescale: imx93-phycore-som: Disable LED pull-up
arm64: dts: freescale: imx93-phycore-som: Enhance eMMC pinctrl
arm64: dts: freescale: imx93-phycore-som: Add eMMC no-1-8-v by default
arm64: dts: freescale: imx93-phyboard-segin: Drop eMMC no-1-8-v flag
arm64: dts: freescale: imx93-phyboard-segin: Disable SD-card
write-protect
arm64: dts: freescale: imx93-phyboard-segin: Fix SD-card pinctrl
arm64: dts: freescale: imx93-phyboard-segin: Set CMD/DATA SION bit to

    fix ERR052021

arm64: dts: freescale: imx93-phyboard-segin: Add RTC support
arm64: dts: freescale: imx93-phyboard-segin: Add CAN support
arm64: dts: freescale: imx93-phyboard-segin: Add USB support
arm64: dts: freescale: imx93-phyboard-segin: Add I2S audio
arm64: dts: freescale: imx93-phyboard-segin: Add EQOS Ethernet
arm64: dts: freescale: imx93-phyboard-segin: Order node alphabetically

 .../dts/freescale/imx93-phyboard-segin.dts    | 243 ++++++++++++++++--
 .../boot/dts/freescale/imx93-phycore-som.dtsi | 165 +++++++++++-
 2 files changed, 369 insertions(+), 39 deletions(-)
Signature · 1 line
2.34.1
#1 lore raw

PATCH v4 1/15 arm64: dts: freescale: imx93-phycore-som: Add PMIC support

PMIC driver for PCA9451A used on phyCORE-i.MX93 SOM is available since commit 5edeb7d31262 ("regulator: pca9450: add pca9451a support"). Add support for it in the SOM device-tree.

---
Changes in v4:
- no changes

 .../boot/dts/freescale/imx93-phycore-som.dtsi | 97 +++++++++++++++++++
 1 file changed, 97 insertions(+)
arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi +97 -0
index 88c2657b50e6..507a71f9294b 100644
@@ -72,6 +72,90 @@ ethphy1: ethernet-phy@1 {
 	};
 };
 
+/* I2C3 */
+&lpi2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c3>;
+	status = "okay";
+
+	pmic@25 {
+		compatible = "nxp,pca9451a";
+		reg = <0x25>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			buck1: BUCK1 {
+				regulator-name = "VDD_SOC";
+				regulator-min-microvolt = <610000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			buck2: BUCK2 {
+				regulator-name = "VDDQ_0V6";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <600000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck4: BUCK4 {
+				regulator-name = "VDD_3V3_BUCK";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5: BUCK5 {
+				regulator-name = "VDD_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6: BUCK6 {
+				regulator-name = "VDD_1V1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1: LDO1 {
+				regulator-name = "PMIC_SNVS_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4: LDO4 {
+				regulator-name = "VDD_0V8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo5: LDO5 {
+				regulator-name = "NVCC_SD2";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
 /* eMMC */
 &usdhc1 {
 	pinctrl-names = "default";
@@ -108,6 +192,19 @@ MX93_PAD_I2C1_SDA__GPIO1_IO01		0x31e
 		>;
 	};
 
+	pinctrl_lpi2c3: lpi2c3grp {
+		fsl,pins = <
+			MX93_PAD_GPIO_IO28__LPI2C3_SDA		0x40000b9e
+			MX93_PAD_GPIO_IO29__LPI2C3_SCL		0x40000b9e
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX93_PAD_ENET2_RD3__GPIO4_IO27		0x31e
+		>;
+	};
+
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			MX93_PAD_SD1_CLK__USDHC1_CLK		0x179e
Signature · 1 line
2.34.1
#2 lore raw

PATCH v4 2/15 arm64: dts: freescale: imx93-phycore-som: Add EEPROM support

In reply to Primoz Fiser

Add support for the EEPROM chip available on I2C3 bus (address 0x50), used for the PHYTEC SOM detection.

---
Changes in v4:
- no changes

 arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)
arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi +8 -0
index 507a71f9294b..0528e293c03d 100644
@@ -154,6 +154,14 @@ ldo5: LDO5 {
 			};
 		};
 	};
+
+	/* EEPROM */
+	eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+		vcc-supply = <&buck4>;
+	};
 };
 
 /* eMMC */
Signature · 1 line
2.34.1
#3 lore raw

PATCH v4 3/15 arm64: dts: freescale: imx93-phycore-som: Disable LED pull-up

In reply to Primoz Fiser

There is already an external pull-down resistor on the LED output line. It makes no sense to have both pull-down and pull-up resistors enabled at the same time. Thus disable the internal pull-up.

---
Changes in v4:
- fix commit message (pull-up/pull-down)

 arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi +1 -1
index 0528e293c03d..06a9e674e338 100644
@@ -196,7 +196,7 @@ MX93_PAD_ENET2_TD2__ENET1_TX_CLK		0x4000050e
 
 	pinctrl_leds: ledsgrp {
 		fsl,pins = <
-			MX93_PAD_I2C1_SDA__GPIO1_IO01		0x31e
+			MX93_PAD_I2C1_SDA__GPIO1_IO01		0x11e
 		>;
 	};
 
Signature · 1 line
2.34.1
#4 lore raw

PATCH v4 4/15 arm64: dts: freescale: imx93-phycore-som: Enhance eMMC pinctrl

In reply to Primoz Fiser

Improve eMMC on phyCORE-i.MX93 SOM by adding 100MHz and 200MHz pinctrl modes. This enables to use eMMC at enhanced data rates (e.g. HS400).

While at it, apply a workaround for the i.MX93 chip errata ERR052021.

---
Changes in v4:
- no changes

 .../boot/dts/freescale/imx93-phycore-som.dtsi | 57 +++++++++++++++----
 1 file changed, 47 insertions(+), 10 deletions(-)
arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi +47 -10
index 06a9e674e338..663530a7e2bb 100644
@@ -166,8 +166,10 @@ eeprom@50 {
 
 /* eMMC */
 &usdhc1 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
 	bus-width = <8>;
 	non-removable;
 	status = "okay";
@@ -213,18 +215,53 @@ MX93_PAD_ENET2_RD3__GPIO4_IO27		0x31e
 		>;
 	};
 
+	/* need to config the SION for data and cmd pad, refer to ERR052021 */
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			MX93_PAD_SD1_CLK__USDHC1_CLK		0x179e
-			MX93_PAD_SD1_CMD__USDHC1_CMD		0x1386
-			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x138e
-			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x1386
-			MX93_PAD_SD1_DATA2__USDHC1_DATA2	0x138e
-			MX93_PAD_SD1_DATA3__USDHC1_DATA3	0x1386
-			MX93_PAD_SD1_DATA4__USDHC1_DATA4	0x1386
-			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x1386
-			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x1386
-			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x1386
+			MX93_PAD_SD1_CMD__USDHC1_CMD		0x40001386
+			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x4000138e
+			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x40001386
+			MX93_PAD_SD1_DATA2__USDHC1_DATA2	0x4000138e
+			MX93_PAD_SD1_DATA3__USDHC1_DATA3	0x40001386
+			MX93_PAD_SD1_DATA4__USDHC1_DATA4	0x40001386
+			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x40001386
+			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x40001386
+			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x40001386
+			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x179e
+		>;
+	};
+
+	/* need to config the SION for data and cmd pad, refer to ERR052021 */
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX93_PAD_SD1_CLK__USDHC1_CLK		0x17be
+			MX93_PAD_SD1_CMD__USDHC1_CMD		0x4000139e
+			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x4000138e
+			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x4000139e
+			MX93_PAD_SD1_DATA2__USDHC1_DATA2	0x400013be
+			MX93_PAD_SD1_DATA3__USDHC1_DATA3	0x4000139e
+			MX93_PAD_SD1_DATA4__USDHC1_DATA4	0x4000139e
+			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x4000139e
+			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x4000139e
+			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x4000139e
+			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x179e
+		>;
+	};
+
+	/* need to config the SION for data and cmd pad, refer to ERR052021 */
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX93_PAD_SD1_CLK__USDHC1_CLK		0x17be
+			MX93_PAD_SD1_CMD__USDHC1_CMD		0x4000139e
+			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x4000139e
+			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x400013be
+			MX93_PAD_SD1_DATA2__USDHC1_DATA2	0x400013be
+			MX93_PAD_SD1_DATA3__USDHC1_DATA3	0x400013be
+			MX93_PAD_SD1_DATA4__USDHC1_DATA4	0x400013be
+			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x400013be
+			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x400013be
+			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x400013be
 			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x179e
 		>;
 	};
Signature · 1 line
2.34.1
#5 lore raw

PATCH v4 5/15 arm64: dts: freescale: imx93-phycore-som: Add eMMC no-1-8-v by default

In reply to Primoz Fiser

The phyCORE-i.MX93 SoM comes in two variants, one with VDD_IO set to 3.3V and the other variant to 1.8V. The 3.3V variant can only support DDR52 mode, while 1.8V variant is capable of HS400ES eMMC mode. The information about VDD_IO option is encoded in the SoM's EEPROM. EEPROM is read in the bootloader and bootloader clears the "no-1-8-v" flag in case of 1.8V SoM variant is detected. Thus add property 'no-1-8-v' by default to usdhc1 (eMMC) node and let bootloader handle the flag. In case EEPROM is erased or read-out fails, flag "no-1-8-v" also ensures fall-back compatibility with both SoM variants.

---
Changes in v4:
- no changes

 arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi +1 -0
index 663530a7e2bb..22dbcc89e311 100644
@@ -172,6 +172,7 @@ &usdhc1 {
 	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
 	bus-width = <8>;
 	non-removable;
+	no-1-8-v;
 	status = "okay";
 };
 
Signature · 1 line
2.34.1
#6 lore raw

PATCH v4 6/15 arm64: dts: freescale: imx93-phyboard-segin: Drop eMMC no-1-8-v flag

In reply to Primoz Fiser

Drop redundant 'no-1-8-v' flag from usdhc1 (eMMC) node. Flag is now set by default in the SOM include file (imx93-phycore-som.dtsi).

---
Changes in v4:
- no changes

 arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts | 5 -----
 1 file changed, 5 deletions(-)
arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts +0 -5
index 85fb188b057f..902b523fc92c 100644
@@ -40,11 +40,6 @@ &lpuart1 {
 	status = "okay";
 };
 
-/* eMMC */
-&usdhc1 {
-	no-1-8-v;
-};
-
 /* SD-Card */
 &usdhc2 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
Signature · 1 line
2.34.1
#7 lore raw

PATCH v4 7/15 arm64: dts: freescale: imx93-phyboard-segin: Disable SD-card write-protect

In reply to Primoz Fiser

Add disable-wp flag (write-protect) to usdhc2 node (SD-card) to get rid of the following kernel boot warning:

host does not support reading read-only switch, assuming write-enable

Micro SD cards can't be physically write-protected like full-sized cards anyways.

---
Changes in v4:
- no changes

 arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts +1 -0
index 902b523fc92c..3d5cd0561362 100644
@@ -48,6 +48,7 @@ &usdhc2 {
 	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>;
 	bus-width = <4>;
 	cd-gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+	disable-wp;
 	no-mmc;
 	no-sdio;
 	vmmc-supply = <&reg_usdhc2_vmmc>;
Signature · 1 line
2.34.1
#8 lore raw

PATCH v4 8/15 arm64: dts: freescale: imx93-phyboard-segin: Fix SD-card pinctrl

In reply to Primoz Fiser

Until now, all usdhc2 (SD-card) pinctrl labels pointed to one pinctrl group "usdhc2grp" which was overwritten twice by the 100 and 200 MHz modes. Fix this by using unique pinctrl names.

Additionally, adjust MX93_PAD_SD2_CLK__USDHC2_CLK pad drive-strength according to values obtained by measurements from the PHYTEC hardware department to improve signal integrity.

---
Changes in v4:
- no changes

 arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts +5 -5
index 3d5cd0561362..541297052b62 100644
@@ -77,7 +77,7 @@ MX93_PAD_SD2_CD_B__GPIO3_IO00		0x31e
 
 	pinctrl_usdhc2_default: usdhc2grp {
 		fsl,pins = <
-			MX93_PAD_SD2_CLK__USDHC2_CLK		0x179e
+			MX93_PAD_SD2_CLK__USDHC2_CLK		0x159e
 			MX93_PAD_SD2_CMD__USDHC2_CMD		0x139e
 			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x138e
 			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x138e
@@ -87,9 +87,9 @@ MX93_PAD_SD2_VSELECT__USDHC2_VSELECT	0x51e
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
-			MX93_PAD_SD2_CLK__USDHC2_CLK            0x179e
+			MX93_PAD_SD2_CLK__USDHC2_CLK		0x159e
 			MX93_PAD_SD2_CMD__USDHC2_CMD            0x139e
 			MX93_PAD_SD2_DATA0__USDHC2_DATA0        0x138e
 			MX93_PAD_SD2_DATA1__USDHC2_DATA1        0x138e
@@ -99,9 +99,9 @@ MX93_PAD_SD2_VSELECT__USDHC2_VSELECT    0x51e
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
-			MX93_PAD_SD2_CLK__USDHC2_CLK            0x178e
+			MX93_PAD_SD2_CLK__USDHC2_CLK		0x158e
 			MX93_PAD_SD2_CMD__USDHC2_CMD            0x139e
 			MX93_PAD_SD2_DATA0__USDHC2_DATA0        0x139e
 			MX93_PAD_SD2_DATA1__USDHC2_DATA1        0x139e
Signature · 1 line
2.34.1
#9 lore raw

PATCH v4 9/15 arm64: dts: freescale: imx93-phyboard-segin: Set CMD/DATA SION bit to fix ERR052021

In reply to Primoz Fiser

Implement fix for i.MX 93 silicon errata ERR052021.

ERR052021 uSDHC: Sometimes uSDHC does not work under VDD_SOC low
drive mode and nominal mode
Description:
uSDHC PADs have one integration issue.
When CMD/DATA lines direction change from output to input, uSDHC controller begin sampling, the integration issue will make input enable signal from uSDHC propagated to the PAD with a long delay, thus the new input value on the pad comes to uSDHC lately. The uSDHC sampled the old input value and the sampling result is wrong.

Workaround:
Set uSDHC CMD/DATA PADs iomux register SION bit to 1, then PADs will propagate input to uSDHC with no delay, so correct value is sampled.

This issue will wrongly trigger the start bit when sample the USDHC command response, cause the USDHC trigger command CRC/index/endbit error, which will finally impact the tuning pass window, especially will impact the standard tuning logic, and can't find a correct delay cell to get the best timing.

Based on commit bb89601282fc ("arm64: dts: imx93-11x11-evk: set SION for cmd and data pad of USDHC").

---
Changes in v4:
- no changes

 .../dts/freescale/imx93-phyboard-segin.dts    | 37 ++++++++++---------
 1 file changed, 20 insertions(+), 17 deletions(-)
arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts +20 -17
index 541297052b62..525f52789f8b 100644
@@ -75,39 +75,42 @@ MX93_PAD_SD2_CD_B__GPIO3_IO00		0x31e
 		>;
 	};
 
+	/* need to config the SION for data and cmd pad, refer to ERR052021 */
 	pinctrl_usdhc2_default: usdhc2grp {
 		fsl,pins = <
 			MX93_PAD_SD2_CLK__USDHC2_CLK		0x159e
-			MX93_PAD_SD2_CMD__USDHC2_CMD		0x139e
-			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x138e
-			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x138e
-			MX93_PAD_SD2_DATA2__USDHC2_DATA2	0x138e
-			MX93_PAD_SD2_DATA3__USDHC2_DATA3	0x139e
+			MX93_PAD_SD2_CMD__USDHC2_CMD		0x4000139e
+			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x4000138e
+			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x4000138e
+			MX93_PAD_SD2_DATA2__USDHC2_DATA2	0x4000138e
+			MX93_PAD_SD2_DATA3__USDHC2_DATA3	0x4000139e
 			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT	0x51e
 		>;
 	};
 
+	/* need to config the SION for data and cmd pad, refer to ERR052021 */
 	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX93_PAD_SD2_CLK__USDHC2_CLK		0x159e
-			MX93_PAD_SD2_CMD__USDHC2_CMD            0x139e
-			MX93_PAD_SD2_DATA0__USDHC2_DATA0        0x138e
-			MX93_PAD_SD2_DATA1__USDHC2_DATA1        0x138e
-			MX93_PAD_SD2_DATA2__USDHC2_DATA2        0x139e
-			MX93_PAD_SD2_DATA3__USDHC2_DATA3        0x139e
-			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT    0x51e
+			MX93_PAD_SD2_CMD__USDHC2_CMD		0x4000139e
+			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x4000138e
+			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x4000138e
+			MX93_PAD_SD2_DATA2__USDHC2_DATA2	0x4000139e
+			MX93_PAD_SD2_DATA3__USDHC2_DATA3	0x4000139e
+			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT	0x51e
 		>;
 	};
 
+	/* need to config the SION for data and cmd pad, refer to ERR052021 */
 	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX93_PAD_SD2_CLK__USDHC2_CLK		0x158e
-			MX93_PAD_SD2_CMD__USDHC2_CMD            0x139e
-			MX93_PAD_SD2_DATA0__USDHC2_DATA0        0x139e
-			MX93_PAD_SD2_DATA1__USDHC2_DATA1        0x139e
-			MX93_PAD_SD2_DATA2__USDHC2_DATA2        0x139e
-			MX93_PAD_SD2_DATA3__USDHC2_DATA3        0x139e
-			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT    0x51e
+			MX93_PAD_SD2_CMD__USDHC2_CMD		0x4000139e
+			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x4000139e
+			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x4000139e
+			MX93_PAD_SD2_DATA2__USDHC2_DATA2	0x4000139e
+			MX93_PAD_SD2_DATA3__USDHC2_DATA3	0x4000139e
+			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT	0x51e
 		>;
 	};
 };
Signature · 1 line
2.34.1
#10 lore raw

PATCH v4 10/15 arm64: dts: freescale: imx93-phyboard-segin: Add RTC support

In reply to Primoz Fiser

Add support for RTC connected via I2C on phyBOARD-Segin-i.MX93. Set default RTC by configuring the aliases.

---
Changes in v4:
- no changes

 .../dts/freescale/imx93-phyboard-segin.dts    | 36 +++++++++++++++++++
 1 file changed, 36 insertions(+)
arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts +36 -0
index 525f52789f8b..38b89398e646 100644
@@ -17,6 +17,11 @@ /{
 	compatible = "phytec,imx93-phyboard-segin", "phytec,imx93-phycore-som",
 		     "fsl,imx93";
 
+	aliases {
+		rtc0 = &i2c_rtc;
+		rtc1 = &bbnsm_rtc;
+	};
+
 	chosen {
 		stdout-path = &lpuart1;
 	};
@@ -33,6 +38,24 @@ reg_usdhc2_vmmc: regulator-usdhc2 {
 	};
 };
 
+/* I2C2 */
+&lpi2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c2>;
+	status = "okay";
+
+	/* RTC */
+	i2c_rtc: rtc@68 {
+		compatible = "microcrystal,rv4162";
+		reg = <0x68>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
 /* Console */
 &lpuart1 {
 	pinctrl-names = "default";
@@ -56,6 +79,13 @@ &usdhc2 {
 };
 
 &iomuxc {
+	pinctrl_lpi2c2: lpi2c2grp {
+		fsl,pins = <
+			MX93_PAD_I2C2_SCL__LPI2C2_SCL		0x40000b9e
+			MX93_PAD_I2C2_SDA__LPI2C2_SDA		0x40000b9e
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX93_PAD_UART1_RXD__LPUART1_RX		0x31e
@@ -69,6 +99,12 @@ MX93_PAD_SD2_RESET_B__GPIO3_IO07	0x31e
 		>;
 	};
 
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX93_PAD_ENET2_RD2__GPIO4_IO26		0x31e
+		>;
+	};
+
 	pinctrl_usdhc2_cd: usdhc2cdgrp {
 		fsl,pins = <
 			MX93_PAD_SD2_CD_B__GPIO3_IO00		0x31e
Signature · 1 line
2.34.1
#11 lore raw

PATCH v4 11/15 arm64: dts: freescale: imx93-phyboard-segin: Add CAN support

In reply to Primoz Fiser

Add support for CAN networking on phyBOARD-Segin-i.MX93 via the flexcan1 interface. The CAN PHY chip SN65HVD234D used on the board is compatible with the TCAN1043 driver using the generic "can-transceiver-phy" and is capable of up to 1Mbps data rate.

---
Changes in v4:
- no changes

 .../dts/freescale/imx93-phyboard-segin.dts    | 30 +++++++++++++++++++
 1 file changed, 30 insertions(+)
arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts +30 -0
index 38b89398e646..be9c0a436734 100644
@@ -26,6 +26,15 @@ chosen {
 		stdout-path = &lpuart1;
 	};
 
+	flexcan1_tc: can-phy0 {
+		compatible = "ti,tcan1043";
+		#phy-cells = <0>;
+		max-bitrate = <1000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flexcan1_tc>;
+		enable-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+	};
+
 	reg_usdhc2_vmmc: regulator-usdhc2 {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -38,6 +47,14 @@ reg_usdhc2_vmmc: regulator-usdhc2 {
 	};
 };
 
+/* CAN */
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	phys = <&flexcan1_tc>;
+	status = "okay";
+};
+
 /* I2C2 */
 &lpi2c2 {
 	clock-frequency = <400000>;
@@ -79,6 +96,19 @@ &usdhc2 {
 };
 
 &iomuxc {
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX93_PAD_PDM_BIT_STREAM0__CAN1_RX	0x139e
+			MX93_PAD_PDM_CLK__CAN1_TX		0x139e
+		>;
+	};
+
+	pinctrl_flexcan1_tc: flexcan1tcgrp {
+		fsl,pins = <
+			MX93_PAD_ENET2_TD3__GPIO4_IO16		0x31e
+		>;
+	};
+
 	pinctrl_lpi2c2: lpi2c2grp {
 		fsl,pins = <
 			MX93_PAD_I2C2_SCL__LPI2C2_SCL		0x40000b9e
Signature · 1 line
2.34.1
#12 lore raw

PATCH v4 12/15 arm64: dts: freescale: imx93-phyboard-segin: Add USB support

In reply to Primoz Fiser

Add support for both USB controllers. Set first controller in OTG mode (USB micro-AB connector X8) and the second one in host mode (USB type A connector X7) by default.

---
Changes in v4:
- no changes

 .../boot/dts/freescale/imx93-phyboard-segin.dts     | 13 +++++++++++++
 1 file changed, 13 insertions(+)
arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts +13 -0
index be9c0a436734..e4f959f665b2 100644
@@ -80,6 +80,19 @@ &lpuart1 {
 	status = "okay";
 };
 
+/* USB  */
+&usbotg1 {
+	disable-over-current;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
+
 /* SD-Card */
 &usdhc2 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
Signature · 1 line
2.34.1
#13 lore raw

PATCH v4 13/15 arm64: dts: freescale: imx93-phyboard-segin: Add I2S audio

In reply to Primoz Fiser

Add support for I2S audio found on phyBOARD-Segin-i.MX93. Audio codec TLV320AIC3007 is connected to SAI1 interface as a DAI master. MCLK is provided from the SAI's internal audio PLL (19.2 MHz).

---
Changes in v4:
- no changes

 .../dts/freescale/imx93-phyboard-segin.dts    | 74 +++++++++++++++++++
 1 file changed, 74 insertions(+)
arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts +74 -0
index e4f959f665b2..54e084e69706 100644
@@ -35,6 +35,20 @@ flexcan1_tc: can-phy0 {
 		enable-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
 	};
 
+	reg_sound_1v8: regulator-sound-1v8 {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "VCC1V8_AUDIO";
+	};
+
+	reg_sound_3v3: regulator-sound-3v3 {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VCC3V3_ANALOG";
+	};
+
 	reg_usdhc2_vmmc: regulator-usdhc2 {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -45,6 +59,34 @@ reg_usdhc2_vmmc: regulator-usdhc2 {
 		regulator-max-microvolt = <3300000>;
 		regulator-name = "VCC_SD";
 	};
+
+	sound: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "phyBOARD-Segin-TLV320AIC3007";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,widgets =
+			"Line", "Line In",
+			"Line", "Line Out",
+			"Speaker", "Speaker";
+		simple-audio-card,routing =
+			"Line Out", "LLOUT",
+			"Line Out", "RLOUT",
+			"Speaker", "SPOP",
+			"Speaker", "SPOM",
+			"LINE1L", "Line In",
+			"LINE1R", "Line In";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai1>;
+		};
+
+		dailink_master: simple-audio-card,codec {
+			sound-dai = <&audio_codec>;
+			clocks = <&clk IMX93_CLK_SAI1>;
+		};
+	};
 };
 
 /* CAN */
@@ -62,6 +104,17 @@ &lpi2c2 {
 	pinctrl-0 = <&pinctrl_lpi2c2>;
 	status = "okay";
 
+	/* Codec */
+	audio_codec: audio-codec@18 {
+		compatible = "ti,tlv320aic3007";
+		reg = <0x18>;
+		#sound-dai-cells = <0>;
+		AVDD-supply = <&reg_sound_3v3>;
+		IOVDD-supply = <&reg_sound_3v3>;
+		DRVDD-supply = <&reg_sound_3v3>;
+		DVDD-supply = <&reg_sound_1v8>;
+	};
+
 	/* RTC */
 	i2c_rtc: rtc@68 {
 		compatible = "microcrystal,rv4162";
@@ -80,6 +133,17 @@ &lpuart1 {
 	status = "okay";
 };
 
+/* Audio */
+&sai1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai1>;
+	assigned-clocks = <&clk IMX93_CLK_SAI1>;
+	assigned-clock-parents = <&clk IMX93_CLK_AUDIO_PLL>;
+	assigned-clock-rates = <19200000>;
+	fsl,sai-mclk-direction-output;
+	status = "okay";
+};
+
 /* USB  */
 &usbotg1 {
 	disable-over-current;
@@ -148,6 +212,16 @@ MX93_PAD_ENET2_RD2__GPIO4_IO26		0x31e
 		>;
 	};
 
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			MX93_PAD_UART2_RXD__SAI1_MCLK		0x1202
+			MX93_PAD_SAI1_TXFS__SAI1_TX_SYNC	0x1202
+			MX93_PAD_SAI1_TXC__SAI1_TX_BCLK		0x1202
+			MX93_PAD_SAI1_TXD0__SAI1_TX_DATA00	0x1402
+			MX93_PAD_SAI1_RXD0__SAI1_RX_DATA00	0x1402
+		>;
+	};
+
 	pinctrl_usdhc2_cd: usdhc2cdgrp {
 		fsl,pins = <
 			MX93_PAD_SD2_CD_B__GPIO3_IO00		0x31e
Signature · 1 line
2.34.1
#14 lore raw

PATCH v4 14/15 arm64: dts: freescale: imx93-phyboard-segin: Add EQOS Ethernet

In reply to Primoz Fiser

Add support for the carrier-board Micrel KSZ8081 Ethernet PHY. This is a 10/100Mbit PHY connected to the EQOS interface and shares MDIO bus with the Ethernet PHY located on the SoM (FEC interface).

---
Changes in v4:
- no changes

 .../dts/freescale/imx93-phyboard-segin.dts    | 35 +++++++++++++++++++
 1 file changed, 35 insertions(+)
arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts +35 -0
index 54e084e69706..c62cc06fad4b 100644
@@ -89,6 +89,28 @@ dailink_master: simple-audio-card,codec {
 	};
 };
 
+/* Ethernet */
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy2>;
+	assigned-clock-parents = <&clk IMX93_CLK_SYS_PLL_PFD1_DIV2>,
+				 <&clk IMX93_CLK_SYS_PLL_PFD1_DIV2>;
+	assigned-clock-rates = <100000000>, <50000000>;
+	status = "okay";
+};
+
+&mdio {
+	ethphy2: ethernet-phy@2 {
+		compatible = "ethernet-phy-id0022.1561";
+		reg = <2>;
+		clocks = <&clk IMX93_CLK_ENET_REF_PHY>;
+		clock-names = "rmii-ref";
+		micrel,led-mode = <1>;
+	};
+};
+
 /* CAN */
 &flexcan1 {
 	pinctrl-names = "default";
@@ -173,6 +195,19 @@ &usdhc2 {
 };
 
 &iomuxc {
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <
+			MX93_PAD_ENET1_TD2__CCM_ENET_QOS_CLOCK_GENERATE_REF_CLK	0x4000050e
+			MX93_PAD_ENET1_RD0__ENET_QOS_RGMII_RD0		0x57e
+			MX93_PAD_ENET1_RD1__ENET_QOS_RGMII_RD1		0x57e
+			MX93_PAD_ENET1_TD0__ENET_QOS_RGMII_TD0		0x50e
+			MX93_PAD_ENET1_TD1__ENET_QOS_RGMII_TD1		0x50e
+			MX93_PAD_ENET1_RX_CTL__ENET_QOS_RGMII_RX_CTL	0x57e
+			MX93_PAD_ENET1_TX_CTL__ENET_QOS_RGMII_TX_CTL	0x50e
+			MX93_PAD_ENET1_RXC__ENET_QOS_RX_ER		0x57e
+		>;
+	};
+
 	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX93_PAD_PDM_BIT_STREAM0__CAN1_RX	0x139e
Signature · 1 line
2.34.1
#15 lore raw

PATCH v4 15/15 arm64: dts: freescale: imx93-phyboard-segin: Order node alphabetically

In reply to Primoz Fiser

Move pinctrl_uart1 to keep nodes in alphabetical order. No functional changes.

---
Changes in v4:
- no changes

 .../boot/dts/freescale/imx93-phyboard-segin.dts    | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)
arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts +7 -7
index c62cc06fad4b..0c55b749c834 100644
@@ -228,13 +228,6 @@ MX93_PAD_I2C2_SDA__LPI2C2_SDA		0x40000b9e
 		>;
 	};
 
-	pinctrl_uart1: uart1grp {
-		fsl,pins = <
-			MX93_PAD_UART1_RXD__LPUART1_RX		0x31e
-			MX93_PAD_UART1_TXD__LPUART1_TX		0x30e
-		>;
-	};
-
 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
 		fsl,pins = <
 			MX93_PAD_SD2_RESET_B__GPIO3_IO07	0x31e
@@ -257,6 +250,13 @@ MX93_PAD_SAI1_RXD0__SAI1_RX_DATA00	0x1402
 		>;
 	};
 
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX93_PAD_UART1_RXD__LPUART1_RX		0x31e
+			MX93_PAD_UART1_TXD__LPUART1_TX		0x30e
+		>;
+	};
+
 	pinctrl_usdhc2_cd: usdhc2cdgrp {
 		fsl,pins = <
 			MX93_PAD_SD2_CD_B__GPIO3_IO00		0x31e
Signature · 1 line
2.34.1
Applied
#16 lore raw
In reply to Primoz Fiser
Quoted 11 lines · Primoz Fiser

Primoz Fiser (15):
arm64: dts: freescale: imx93-phycore-som: Add PMIC support
arm64: dts: freescale: imx93-phycore-som: Add EEPROM support
arm64: dts: freescale: imx93-phycore-som: Disable LED pull-up
arm64: dts: freescale: imx93-phycore-som: Enhance eMMC pinctrl
arm64: dts: freescale: imx93-phycore-som: Add eMMC no-1-8-v by default
arm64: dts: freescale: imx93-phyboard-segin: Drop eMMC no-1-8-v flag
arm64: dts: freescale: imx93-phyboard-segin: Disable SD-card
write-protect
arm64: dts: freescale: imx93-phyboard-segin: Fix SD-card pinctrl
arm64: dts: freescale: imx93-phyboard-segin: Set CMD/DATA SION bit to

Quoted 7 lines
    fix ERR052021

arm64: dts: freescale: imx93-phyboard-segin: Add RTC support
arm64: dts: freescale: imx93-phyboard-segin: Add CAN support
arm64: dts: freescale: imx93-phyboard-segin: Add USB support
arm64: dts: freescale: imx93-phyboard-segin: Add I2S audio
arm64: dts: freescale: imx93-phyboard-segin: Add EQOS Ethernet
arm64: dts: freescale: imx93-phyboard-segin: Order node alphabetically

Applied all, thanks!