added zynq 7000 usb support
Subsystems (3)
PATCH v2 1/1 added zynq 7000 usb support
This adds support to use the USB interface on Zynq-7000 SoC.
Signed-off-by Michael Graichen <[email protected]>
Signed-off-by Johannes Roith <[email protected]>
--- drivers/usb/host/Kconfig | 8 ++++++++ drivers/usb/host/Makefile | 1 + drivers/usb/host/ehci-zynq.c | 36 ++++++++++++++++++++++++++++++++++++ 3 files changed, 45 insertions(+) create mode 100644 drivers/usb/host/ehci-zynq.c
drivers/usb/host/Kconfig +8 -0
@@ -14,6 +14,14 @@ config USB_EHCI_ATMEL select USB_OHCI_AT91 bool "Atmel EHCI driver" +config USB_EHCI_ZYNQ + bool "Support for Xilinx Zynq on-chip EHCI USB controller" + depends on ARCH_ZYNQ + depends on USB_EHCI + select USB_ULPI + help + Enable support for Zynq on-chip EHCI USB controller + config USB_OHCI bool "OHCI driver" depends on !MMU && HAS_DMA
drivers/usb/host/Makefile +1 -0
@@ -2,6 +2,7 @@ obj-$(CONFIG_USB_EHCI) += ehci-hcd.o obj-$(CONFIG_USB_EHCI_OMAP) += ehci-omap.o obj-$(CONFIG_USB_EHCI_ATMEL) += ehci-atmel.o +obj-$(CONFIG_USB_EHCI_ZYNQ) += ehci-zynq.o obj-$(CONFIG_USB_OHCI) += ohci-hcd.o obj-$(CONFIG_USB_OHCI_AT91) += ohci-at91.o obj-$(CONFIG_USB_XHCI) += xhci.o xhci-mem.o xhci-ring.o
drivers/usb/host/ehci-zynq.c new file +36 -0
@@ -0,0 +1,36 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* USB Low level initialization(Specific to Zynq 7000) +*/ + +#include <common.h> +#include <linux/usb/ulpi.h> + +static int zynq_ehci_probe (struct device_d *dev) +{ +struct resource *res; +void __iomem *base; + + res =dev_get_resource (dev,IORESOURCE_MEM ,0 ); +if (IS_ERR (res)) +return PTR_ERR (res); + + base =IOMEM (res->start); + +ulpi_setup (base +0x170 ,1 ); +add_generic_usb_ehci_device (DEVICE_ID_DYNAMIC , (unsigned int )base,NULL ); + +return 0 ; +} + +static const struct of_device_id zynq_ehci_dt_ids[] = { + { .compatible ="xlnx,zynq-usb-2.20a" }, + {/* sentinel */ } +}; + +static struct driver_d zynq_ehci_driver = { + .name ="zynq-ehci" , + .probe = zynq_ehci_probe, + .of_compatible =DRV_OF_COMPAT (zynq_ehci_dt_ids), +}; +device_platform_driver (zynq_ehci_driver);
Signature · 1 line
2.39.5
Sascha Hauer
AppliedQuoted 3 lines · Johannes Roith
This adds support to use the USB interface on Zynq-7000 SoC.
Applied, thanks!
[1/1] added zynq 7000 usb support
https://git.pengutronix.de/cgit/barebox/commit/?id=c69d280f3137 (link may not be stable)
Best regards,
Signature · 1 line
Sascha Hauer <[email protected]>