Skip to contentSkip to conversation

HID: mcp2221: set gpio pin mode

PATCH In review Heiko Schocher 2 participants 3 messages Jun 8, 2025 – Jun 20, 2025

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 HID: mcp2221: set gpio pin mode

in case we have GPIOLIB enabled the gpio pins are used from the current driver as gpio pins. But may the gpio functions of this pins are not enabled in the flash of the chip and so gpio access fails.

In case CONFIG_IIO is not enabled we can prevent this issue of the driver simply by enabling the gpio mode for all pins.

---

 drivers/hid/hid-mcp2221.c | 97 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 97 insertions(+)
drivers/hid/hid-mcp2221.c +97 -0
index 0f93c22a479f..f693e920dffe 100644
@@ -55,6 +55,27 @@ enum {
 	MCP2221_ALT_F_NOT_GPIOD = 0xEF,
 };
 
+/* MCP SRAM read offsets cmd: MCP2221_GET_SRAM_SETTINGS */
+enum {
+	MCP2221_SRAM_RD_GP0 = 22,
+	MCP2221_SRAM_RD_GP1 = 23,
+	MCP2221_SRAM_RD_GP2 = 24,
+	MCP2221_SRAM_RD_GP3 = 25,
+};
+
+/* MCP SRAM write offsets cmd: MCP2221_SET_SRAM_SETTINGS */
+enum {
+	MCP2221_SRAM_WR_GP_ENA_ALTER = 7,
+	MCP2221_SRAM_WR_GP0 = 8,
+	MCP2221_SRAM_WR_GP1 = 9,
+	MCP2221_SRAM_WR_GP2 = 10,
+	MCP2221_SRAM_WR_GP3 = 11,
+};
+
+#define MCP2221_SRAM_GP_DESIGN_MASK		0x07
+#define MCP2221_SRAM_GP_DIRECTION_MASK		0x08
+#define MCP2221_SRAM_GP_VALUE_MASK		0x10
+
 /* MCP GPIO direction encoding */
 enum {
 	MCP2221_DIR_OUT = 0x00,
@@ -607,6 +628,80 @@ static const struct i2c_algorithm mcp_i2c_algo = {
 };
 
 #if IS_REACHABLE(CONFIG_GPIOLIB)
+static int mcp_gpio_read_sram(struct mcp2221 *mcp)
+{
+	int ret;
+
+	memset(mcp->txbuf, 0, 64);
+	mcp->txbuf[0] = MCP2221_GET_SRAM_SETTINGS;
+
+	mutex_lock(&mcp->lock);
+	ret = mcp_send_data_req_status(mcp, mcp->txbuf, 64);
+	mutex_unlock(&mcp->lock);
+
+	return ret;
+}
+
+/*
+ * If CONFIG_IIO is not enabled, check for the gpio pins
+ * if they are in gpio mode. For the ones which are not
+ * in gpio mode, set them into gpio mode.
+ */
+static int mcp2221_check_gpio_pinfunc(struct mcp2221 *mcp)
+{
+	int i;
+	int needgpiofix = 0;
+	int ret;
+
+	if (IS_ENABLED(CONFIG_IIO))
+		return 0;
+
+	ret = mcp_gpio_read_sram(mcp);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < MCP_NGPIO; i++) {
+		if ((mcp->mode[i] & MCP2221_SRAM_GP_DESIGN_MASK) != 0x0) {
+			dev_warn(&mcp->hdev->dev,
+				 "GPIO %d not in gpio mode\n", i);
+			needgpiofix = 1;
+		}
+	}
+
+	if (!needgpiofix)
+		return 0;
+
+	/*
+	 * Set all bytes to 0, so Bit 7 is not set. The chip
+	 * only changes content of a register when bit 7 is set.
+	 */
+	memset(mcp->txbuf, 0, 64);
+	mcp->txbuf[0] = MCP2221_SET_SRAM_SETTINGS;
+
+	/*
+	 * Set bit 7 in MCP2221_SRAM_WR_GP_ENA_ALTER to enable
+	 * loading of a new set of gpio settings to GP SRAM
+	 */
+	mcp->txbuf[MCP2221_SRAM_WR_GP_ENA_ALTER] = 0x80;
+	for (i = 0; i < MCP_NGPIO; i++) {
+		if ((mcp->mode[i] & MCP2221_SRAM_GP_DESIGN_MASK) == 0x0) {
+			/* write current GPIO mode */
+			mcp->txbuf[MCP2221_SRAM_WR_GP0 + i] = mcp->mode[i];
+		} else {
+			/* pin is not in gpio mode, set it to input mode */
+			mcp->txbuf[MCP2221_SRAM_WR_GP0 + i] = 0x08;
+			dev_warn(&mcp->hdev->dev,
+				 "Set GPIO mode for gpio pin %d!\n", i);
+		}
+	}
+
+	mutex_lock(&mcp->lock);
+	ret = mcp_send_data_req_status(mcp, mcp->txbuf, 64);
+	mutex_unlock(&mcp->lock);
+
+	return ret;
+}
+
 static int mcp_gpio_get(struct gpio_chip *gc,
 				unsigned int offset)
 {
@@ -1216,6 +1311,8 @@ static int mcp2221_probe(struct hid_device *hdev,
 	ret = devm_gpiochip_add_data(&hdev->dev, mcp->gc, mcp);
 	if (ret)
 		return ret;
+
+	mcp2221_check_gpio_pinfunc(mcp);
 #endif
 
 #if IS_REACHABLE(CONFIG_IIO)
Signature · 4 lines
2.20.1

base-commit: 546b1c9e93c2bb8cf5ed24e0be1c86bb089b3253
branch: abb-mcp2221-v1
#1 lore raw

Hi all,

Quoted 9 lines · Heiko Schocher

in case we have GPIOLIB enabled the gpio pins are used from the current driver as gpio pins. But may the gpio functions of this pins are not enabled in the flash of the chip and so gpio access fails.

In case CONFIG_IIO is not enabled we can prevent this issue of the driver simply by enabling the gpio mode for all pins.

Quoted 5 lines

---

  drivers/hid/hid-mcp2221.c | 97 +++++++++++++++++++++++++++++++++++++++
  1 file changed, 97 insertions(+)

Got message from patchwork:
The following patch (submitted by you) has been updated in Patchwork:
"""
* linux-i2c: HID: mcp2221: set gpio pin mode
- http://patchwork.ozlabs.org/project/linux-i2c/patch/[email protected]/
- for: Linux I2C development
was: New
now: Not Applicable
"""

May I ask to which tree I should rebase my patch, so I can resend? Just rebased my local patch to:

* fb4d33ab452e - (origin/master, origin/HEAD, master) Merge tag '6.16-rc2-ksmbd-server-fixes' of git://git.samba.org/ksmbd

and it worked without problems.

And while at it, are there any issues with this patch or is it ready for picking up?

Thanks!

bye,
Heiko

Quoted 124 lines
drivers/hid/hid-mcp2221.c +97 -0
index 0f93c22a479f..f693e920dffe 100644
@@ -55,6 +55,27 @@ enum {
  	MCP2221_ALT_F_NOT_GPIOD = 0xEF,
  };
 
+/* MCP SRAM read offsets cmd: MCP2221_GET_SRAM_SETTINGS */
+enum {
+	MCP2221_SRAM_RD_GP0 = 22,
+	MCP2221_SRAM_RD_GP1 = 23,
+	MCP2221_SRAM_RD_GP2 = 24,
+	MCP2221_SRAM_RD_GP3 = 25,
+};
+
+/* MCP SRAM write offsets cmd: MCP2221_SET_SRAM_SETTINGS */
+enum {
+	MCP2221_SRAM_WR_GP_ENA_ALTER = 7,
+	MCP2221_SRAM_WR_GP0 = 8,
+	MCP2221_SRAM_WR_GP1 = 9,
+	MCP2221_SRAM_WR_GP2 = 10,
+	MCP2221_SRAM_WR_GP3 = 11,
+};
+
+#define MCP2221_SRAM_GP_DESIGN_MASK		0x07
+#define MCP2221_SRAM_GP_DIRECTION_MASK		0x08
+#define MCP2221_SRAM_GP_VALUE_MASK		0x10
+
  /* MCP GPIO direction encoding */
  enum {
  	MCP2221_DIR_OUT = 0x00,
@@ -607,6 +628,80 @@ static const struct i2c_algorithm mcp_i2c_algo = {
  };
 
  #if IS_REACHABLE(CONFIG_GPIOLIB)
+static int mcp_gpio_read_sram(struct mcp2221 *mcp)
+{
+	int ret;
+
+	memset(mcp->txbuf, 0, 64);
+	mcp->txbuf[0] = MCP2221_GET_SRAM_SETTINGS;
+
+	mutex_lock(&mcp->lock);
+	ret = mcp_send_data_req_status(mcp, mcp->txbuf, 64);
+	mutex_unlock(&mcp->lock);
+
+	return ret;
+}
+
+/*
+ * If CONFIG_IIO is not enabled, check for the gpio pins
+ * if they are in gpio mode. For the ones which are not
+ * in gpio mode, set them into gpio mode.
+ */
+static int mcp2221_check_gpio_pinfunc(struct mcp2221 *mcp)
+{
+	int i;
+	int needgpiofix = 0;
+	int ret;
+
+	if (IS_ENABLED(CONFIG_IIO))
+		return 0;
+
+	ret = mcp_gpio_read_sram(mcp);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < MCP_NGPIO; i++) {
+		if ((mcp->mode[i] & MCP2221_SRAM_GP_DESIGN_MASK) != 0x0) {
+			dev_warn(&mcp->hdev->dev,
+				 "GPIO %d not in gpio mode\n", i);
+			needgpiofix = 1;
+		}
+	}
+
+	if (!needgpiofix)
+		return 0;
+
+	/*
+	 * Set all bytes to 0, so Bit 7 is not set. The chip
+	 * only changes content of a register when bit 7 is set.
+	 */
+	memset(mcp->txbuf, 0, 64);
+	mcp->txbuf[0] = MCP2221_SET_SRAM_SETTINGS;
+
+	/*
+	 * Set bit 7 in MCP2221_SRAM_WR_GP_ENA_ALTER to enable
+	 * loading of a new set of gpio settings to GP SRAM
+	 */
+	mcp->txbuf[MCP2221_SRAM_WR_GP_ENA_ALTER] = 0x80;
+	for (i = 0; i < MCP_NGPIO; i++) {
+		if ((mcp->mode[i] & MCP2221_SRAM_GP_DESIGN_MASK) == 0x0) {
+			/* write current GPIO mode */
+			mcp->txbuf[MCP2221_SRAM_WR_GP0 + i] = mcp->mode[i];
+		} else {
+			/* pin is not in gpio mode, set it to input mode */
+			mcp->txbuf[MCP2221_SRAM_WR_GP0 + i] = 0x08;
+			dev_warn(&mcp->hdev->dev,
+				 "Set GPIO mode for gpio pin %d!\n", i);
+		}
+	}
+
+	mutex_lock(&mcp->lock);
+	ret = mcp_send_data_req_status(mcp, mcp->txbuf, 64);
+	mutex_unlock(&mcp->lock);
+
+	return ret;
+}
+
  static int mcp_gpio_get(struct gpio_chip *gc,
  				unsigned int offset)
  {
@@ -1216,6 +1311,8 @@ static int mcp2221_probe(struct hid_device *hdev,
  	ret = devm_gpiochip_add_data(&hdev->dev, mcp->gc, mcp);
  	if (ret)
  		return ret;
+
+	mcp2221_check_gpio_pinfunc(mcp);
  #endif
 
  #if IS_REACHABLE(CONFIG_IIO)
Signature · 3 lines
DENX Software Engineering GmbH,      Managing Director: Erika Unter
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-52   Fax: +49-8142-66989-80   Email: [email protected]
maintainer
#2 lore raw
In reply to Heiko Schocher
Quoted 10 lines · Heiko Schocher

in case we have GPIOLIB enabled the gpio pins are used from the current driver as gpio pins. But may the gpio functions of this pins are not enabled in the flash of the chip and so gpio access fails.

In case CONFIG_IIO is not enabled we can prevent this issue of the driver simply by enabling the gpio mode for all pins.

Now applied to hid.git#for-6.17/mcp2221. Thanks,

Signature · 2 lines
Jiri Kosina
SUSE Labs