Skip to contentSkip to conversation

PCI: Fix secondary bus wait return value when D3cold delay = 0

PATCH In review Ilpo Järvinen 2 participants 2 messages Jun 10, 2025 – Jun 19, 2025 PCI

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 PCI: Fix secondary bus wait return value when D3cold delay = 0

If D3cold delay is zero, pci_bridge_wait_for_secondary_bus() immediately returns 0 which is inconsistent with the rest of the function.

When D3cold delay is 0, infer the return value like in the other cases. With link_active_reporting, use Data Link Layer Link Active (PCIe spec r6.2 sec. 7.5.3.8) and otherwise call pci_dev_wait() with zero delay.

Fixes ad9001f2f411 ("PCI/PM: Add missing link delays required by the PCIe spec")

---

I've not seen this to cause issue anywhere, it's just the inconsistency that caught my eye while trying to figure an entirely unrelated issue.

 drivers/pci/pci.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)
drivers/pci/pci.c +9 -6
index e9448d55113b..a6182261b433 100644
@@ -4848,6 +4848,7 @@ int pci_bridge_wait_for_secondary_bus(struct pci_dev *dev, char *reset_type)
 {
 	struct pci_dev *child __free(pci_dev_put) = NULL;
 	int delay;
+	u16 status;
 
 	if (pci_dev_is_disconnected(dev))
 		return 0;
@@ -4870,15 +4871,19 @@ int pci_bridge_wait_for_secondary_bus(struct pci_dev *dev, char *reset_type)
 
 	/* Take d3cold_delay requirements into account */
 	delay = pci_bus_max_d3cold_delay(dev->subordinate);
-	if (!delay) {
-		up_read(&pci_bus_sem);
-		return 0;
-	}
 
 	child = pci_dev_get(list_first_entry(&dev->subordinate->devices,
 					     struct pci_dev, bus_list));
 	up_read(&pci_bus_sem);
 
+	if (!delay) {
+		if (dev->link_active_reporting) {
+			pcie_capability_read_word(dev, PCI_EXP_LNKSTA, &status);
+			return status & PCI_EXP_LNKSTA_DLLLA ? 0 : -ENOTTY;
+		}
+		return pci_dev_wait(child, reset_type, 0);
+	}
+
 	/*
 	 * Conventional PCI and PCI-X we need to wait Tpvrh + Trhfa before
 	 * accessing the device after reset (that is 1000 ms + 100 ms).
@@ -4908,8 +4913,6 @@ int pci_bridge_wait_for_secondary_bus(struct pci_dev *dev, char *reset_type)
 		return 0;
 
 	if (pcie_get_speed_cap(dev) <= PCIE_SPEED_5_0GT) {
-		u16 status;
-
 		pci_dbg(dev, "waiting %d ms for downstream link\n", delay);
 		msleep(delay);
 

base-commit: 19272b37aa4f83ca52bdf9c16d5d81bdd1354494

Signature · 1 line
2.39.5
#1 lore raw
Quoted 7 lines · Ilpo Järvinen

If D3cold delay is zero, pci_bridge_wait_for_secondary_bus() immediately returns 0 which is inconsistent with the rest of the function.

When D3cold delay is 0, infer the return value like in the other cases. With link_active_reporting, use Data Link Layer Link Active (PCIe spec r6.2 sec. 7.5.3.8) and otherwise call pci_dev_wait() with zero delay.

I guess Mika implemented it this way on purpose:

If d3cold_delay is zero, the devices on the secondary bus are immediately available and there's no need to wait. Note that pci_bus_max_d3cold_delay() goes below the default min_delay of 100 only if pdev->d3cold_delay is lower.

And pci_pm_init() initializes d3cold_delay to PCI_PM_D3COLD_WAIT (which is also 100). So d3cold_delay has a different value only if it's changed in a quirk or similar.

pci_acpi_optimize_delay() actually sets d3cold_delay to zero under certain conditions, so your patch *will* cause a change of behavior.

Bottom line is, I think there's nothing to fix here.

Thanks,

Lukas