Skip to contentSkip to conversation

Increase i.MX8MP VPU

PATCH Applied Adam Ford 3 participants 8 messages Jun 12, 2025 – Jul 2, 2025

Subsystems (2)
lore
Share & tools
lore

Adam Ford

author
#0 lore raw

v2 cover Increase i.MX8MP VPU

Some of the VPU clocks are under rated, even for nominal ratings. Fix the nominial VPU clocks and clock parents, then introduce the overdrive clock rates. The fluster scores don't change, but they do go faster.

This series was adapted from an RFC from Marco Felsch which was setup to introduce the VC8000E encoder and extacted the parts that affect the existing infrastructure.

V2: The only change is 4/4. Patches 1-3 are all unchanged.

Adam Ford (2):
arm64: dts: imx8mp-nominal: Explicitly configure nominal VPU clocks
arm64: dts: imx8mp: Configure VPU clocks for overdrive

Marco Felsch (2):
arm64: dts: imx8mp: drop gpcv2 vpu power-domains and clocks
arm64: dts: imx8mp: fix VPU_BUS clock setting

 .../boot/dts/freescale/imx8mp-nominal.dtsi    | 18 +++++++++++++++
 arch/arm64/boot/dts/freescale/imx8mp.dtsi     | 23 +++++++------------
 2 files changed, 26 insertions(+), 15 deletions(-)
Signature · 1 line
2.48.1
author
#1 lore raw

PATCH v2 1/4 arm64: dts: imx8mp: drop gpcv2 vpu power-domains and clocks

From: Marco Felsch <[email protected]>

The GPCv2 G1, G2 and VC8000E power-domain don't need to reference the VPUMIX power-domain nor their module clocks since the power and reset handling is done by the VPUMIX blkctrl driver.

arch/arm64/boot/dts/freescale/imx8mp.dtsi +0 -7
index 948b88cf5e9d..1bf15c502280 100644
@@ -876,24 +876,17 @@ pgc_mediamix: power-domain@10 {
 
 					pgc_vpu_g1: power-domain@11 {
 						#power-domain-cells = <0>;
-						power-domains = <&pgc_vpumix>;
 						reg = <IMX8MP_POWER_DOMAIN_VPU_G1>;
-						clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>;
 					};
 
 					pgc_vpu_g2: power-domain@12 {
 						#power-domain-cells = <0>;
-						power-domains = <&pgc_vpumix>;
 						reg = <IMX8MP_POWER_DOMAIN_VPU_G2>;
-						clocks = <&clk IMX8MP_CLK_VPU_G2_ROOT>;
-
 					};
 
 					pgc_vpu_vc8000e: power-domain@13 {
 						#power-domain-cells = <0>;
-						power-domains = <&pgc_vpumix>;
 						reg = <IMX8MP_POWER_DOMAIN_VPU_VC8000E>;
-						clocks = <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>;
 					};
 
 					pgc_hdmimix: power-domain@14 {
Signature · 1 line
2.48.1
author
#2 lore raw

PATCH v2 2/4 arm64: dts: imx8mp: fix VPU_BUS clock setting

In reply to Adam Ford

From: Marco Felsch <[email protected]>

The VPU_PLL clock must be set before the VPU_BUS clock which is derived from the VPU_PLL clock else the VPU_BUS clock is 300MHz and not 600MHz.

arch/arm64/boot/dts/freescale/imx8mp.dtsi +2 -2
index 1bf15c502280..909555a5da4b 100644
@@ -2283,8 +2283,8 @@ vpumix_blk_ctrl: blk-ctrl@38330000 {
 				 <&clk IMX8MP_CLK_VPU_G2_ROOT>,
 				 <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>;
 			clock-names = "g1", "g2", "vc8000e";
-			assigned-clocks = <&clk IMX8MP_CLK_VPU_BUS>, <&clk IMX8MP_VPU_PLL>;
-			assigned-clock-parents = <&clk IMX8MP_VPU_PLL_OUT>;
+			assigned-clocks = <&clk IMX8MP_VPU_PLL>, <&clk IMX8MP_CLK_VPU_BUS>;
+			assigned-clock-parents = <0>, <&clk IMX8MP_VPU_PLL_OUT>;
 			assigned-clock-rates = <600000000>, <600000000>;
 			interconnects = <&noc IMX8MP_ICM_VPU_G1 &noc IMX8MP_ICN_VIDEO>,
 					<&noc IMX8MP_ICM_VPU_G2 &noc IMX8MP_ICN_VIDEO>,
Signature · 1 line
2.48.1
author
#3 lore raw

PATCH v2 3/4 arm64: dts: imx8mp-nominal: Explicitly configure nominal VPU clocks

In reply to Adam Ford

In preparation for increasing the default VPU clocks to overdrive, configure the nominal values first to avoid running the nominal devices out of spec when imx8mp.dtsi is changed.

arch/arm64/boot/dts/freescale/imx8mp-nominal.dtsi +18 -0
index 2ce1860b244d..f269f7a004fc 100644
@@ -89,4 +89,22 @@ &media_blk_ctrl {
 			       <1039500000>;
 };
 
+&vpu_g1 {
+	assigned-clocks = <&clk IMX8MP_CLK_VPU_G1>;
+	assigned-clock-parents = <&clk IMX8MP_VPU_PLL_OUT>;
+	assigned-clock-rates = <600000000>;
+};
+
+&vpu_g2 {
+	assigned-clocks = <&clk IMX8MP_CLK_VPU_G2>;
+	assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_1000M>;
+	assigned-clock-rates = <500000000>;
+};
+
+&vpumix_blk_ctrl {
+	assigned-clocks = <&clk IMX8MP_VPU_PLL>, <&clk IMX8MP_CLK_VPU_BUS>;
+	assigned-clock-parents = <0>, <&clk IMX8MP_VPU_PLL_OUT>;
+	assigned-clock-rates = <600000000>, <600000000>;
+};
+
 /delete-node/ &{noc_opp_table/opp-1000000000};
Signature · 1 line
2.48.1
Reviewed-by on v2 3/4
#4 lore raw

Re: [PATCH V2 3/4] arm64: dts: imx8mp-nominal: Explicitly configure nominal VPU clocks

Quoted 8 lines · Adam Ford

In preparation for increasing the default VPU clocks to overdrive, configure the nominal values first to avoid running the nominal devices out of spec when imx8mp.dtsi is changed.

author
#5 lore raw

PATCH v2 4/4 arm64: dts: imx8mp: Configure VPU clocks for overdrive

In reply to Adam Ford

The defaults for this SoC are configured for overdrive mode, but the VPU clocks are currently configured for nominal mode. Increase VPU_G1_CLK_ROOT to 800MHZ from 600MHz, Increase VPU_G2_CLK_ROOT to 700MHZ from 500MHz, and Increase VPU_BUS_CLK_ROOT to 800MHz from 600MHz.

This requires adjusting the clock parents. Since there is already 800MHz clock references, move the VPU_BUS and G1 clocks to it. This frees up the VPU_PLL to be configured at 700MHz to run the G2 clock at 700MHz.

---
V2: Move VPU_PLL assignment into the G2 node, since it's only needed
for it.

arch/arm64/boot/dts/freescale/imx8mp.dtsi +8 -8
index 909555a5da4b..8884b3fe5e60 100644
@@ -2256,8 +2256,8 @@ vpu_g1: video-codec@38300000 {
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>;
 			assigned-clocks = <&clk IMX8MP_CLK_VPU_G1>;
-			assigned-clock-parents = <&clk IMX8MP_VPU_PLL_OUT>;
-			assigned-clock-rates = <600000000>;
+			assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>;
+			assigned-clock-rates = <800000000>;
 			power-domains = <&vpumix_blk_ctrl IMX8MP_VPUBLK_PD_G1>;
 		};
 
@@ -2266,9 +2266,9 @@ vpu_g2: video-codec@38310000 {
 			reg = <0x38310000 0x10000>;
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk IMX8MP_CLK_VPU_G2_ROOT>;
-			assigned-clocks = <&clk IMX8MP_CLK_VPU_G2>;
-			assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_1000M>;
-			assigned-clock-rates = <500000000>;
+			assigned-clocks = <&clk IMX8MP_CLK_VPU_G2>, <&clk IMX8MP_VPU_PLL_OUT>;
+			assigned-clock-parents = <&clk IMX8MP_VPU_PLL_OUT>;
+			assigned-clock-rates = <700000000>, <700000000>;
 			power-domains = <&vpumix_blk_ctrl IMX8MP_VPUBLK_PD_G2>;
 		};
 
@@ -2283,9 +2283,9 @@ vpumix_blk_ctrl: blk-ctrl@38330000 {
 				 <&clk IMX8MP_CLK_VPU_G2_ROOT>,
 				 <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>;
 			clock-names = "g1", "g2", "vc8000e";
-			assigned-clocks = <&clk IMX8MP_VPU_PLL>, <&clk IMX8MP_CLK_VPU_BUS>;
-			assigned-clock-parents = <0>, <&clk IMX8MP_VPU_PLL_OUT>;
-			assigned-clock-rates = <600000000>, <600000000>;
+			assigned-clocks = <&clk IMX8MP_CLK_VPU_BUS>;
+			assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>;
+			assigned-clock-rates = <800000000>;
 			interconnects = <&noc IMX8MP_ICM_VPU_G1 &noc IMX8MP_ICN_VIDEO>,
 					<&noc IMX8MP_ICM_VPU_G2 &noc IMX8MP_ICN_VIDEO>,
 					<&noc IMX8MP_ICM_VPU_H1 &noc IMX8MP_ICN_VIDEO>;
Signature · 1 line
2.48.1
Reviewed-by on v2 4/4
#6 lore raw

Re: [PATCH V2 4/4] arm64: dts: imx8mp: Configure VPU clocks for overdrive

Quoted 6 lines · Adam Ford

The defaults for this SoC are configured for overdrive mode, but the VPU clocks are currently configured for nominal mode. Increase VPU_G1_CLK_ROOT to 800MHZ from 600MHz, Increase VPU_G2_CLK_ROOT to 700MHZ from 500MHz, and Increase VPU_BUS_CLK_ROOT to 800MHz from 600MHz.

Quoted 6 lines

This requires adjusting the clock parents. Since there is already 800MHz clock references, move the VPU_BUS and G1 clocks to it. This frees up the VPU_PLL to be configured at 700MHz to run the G2 clock at 700MHz.

Applied
#7 lore raw
In reply to Adam Ford
Quoted 11 lines · Adam Ford

Some of the VPU clocks are under rated, even for nominal ratings. Fix the nominial VPU clocks and clock parents, then introduce the overdrive clock rates. The fluster scores don't change, but they do go faster.

This series was adapted from an RFC from Marco Felsch which was setup to introduce the VC8000E encoder and extacted the parts that affect the existing infrastructure.

V2: The only change is 4/4. Patches 1-3 are all unchanged.

Quoted 7 lines

Adam Ford (2):
arm64: dts: imx8mp-nominal: Explicitly configure nominal VPU clocks
arm64: dts: imx8mp: Configure VPU clocks for overdrive

Marco Felsch (2):
arm64: dts: imx8mp: drop gpcv2 vpu power-domains and clocks
arm64: dts: imx8mp: fix VPU_BUS clock setting

Applied all, thanks!