Skip to contentSkip to conversation

arm64: dts: imx8mm-beacon: Fix HS400 USDHC clock speed

PATCH Applied Adam Ford 4 participants 9 messages Jun 20, 2025 – Jul 7, 2025

Subsystems (2)
lore
Share & tools
lore

Adam Ford

author
#0 lore raw

PATCH 1/2 arm64: dts: imx8mm-beacon: Fix HS400 USDHC clock speed

The reference manual for the i.MX8MM states the clock rate in MMC mode is 1/2 of the input clock, therefore to properly run at HS400 rates, the input clock must be 400MHz to operate at 200MHz. Currently the clock is set to 200MHz which is half the rate it should be, so the throughput is half of what it should be for HS400 operation.

Fixes 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi +2 -0
index 21bcd82fd092..8287a7f66ed3 100644
@@ -294,6 +294,8 @@ &usdhc3 {
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC3>;
+	assigned-clock-rates = <400000000>;
 	bus-width = <8>;
 	non-removable;
 	status = "okay";
Signature · 1 line
2.48.1
author
#1 lore raw

PATCH 2/2 arm64: dts: imx8mn-beacon: Fix HS400 USDHC clock speed

The reference manual for the i.MX8MN states the clock rate in MMC mode is 1/2 of the input clock, therefore to properly run at HS400 rates, the input clock must be 400MHz to operate at 200MHz. Currently the clock is set to 200MHz which is half the rate it should be, so the throughput is half of what it should be for HS400 operation.

Fixes 36ca3c8ccb53 ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")
arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi +2 -0
index 67a99383a632..917b7d0007a7 100644
@@ -305,6 +305,8 @@ &usdhc3 {
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	assigned-clocks = <&clk IMX8MN_CLK_USDHC3>;
+	assigned-clock-rates = <400000000>;
 	bus-width = <8>;
 	non-removable;
 	status = "okay";
Signature · 1 line
2.48.1
reviewer Reviewed-by on v1 2/2
#2 lore raw

Re: [PATCH 2/2] arm64: dts: imx8mn-beacon: Fix HS400 USDHC clock speed

Quoted 10 lines · Adam Ford

The reference manual for the i.MX8MN states the clock rate in MMC mode is 1/2 of the input clock, therefore to properly run at HS400 rates, the input clock must be 400MHz to operate at 200MHz. Currently the clock is set to 200MHz which is half the rate it should be, so the throughput is half of what it should be for HS400 operation.

Fixes 36ca3c8ccb53 ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")
#3 lore raw
In reply to Adam Ford
Quoted 25 lines · Adam Ford

The reference manual for the i.MX8MM states the clock rate in MMC mode is 1/2 of the input clock, therefore to properly run at HS400 rates, the input clock must be 400MHz to operate at 200MHz. Currently the clock is set to 200MHz which is half the rate it should be, so the throughput is half of what it should be for HS400 operation.

Fixes 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi +2 -1
index 21bcd82fd092..8287a7f66ed3 100644
@@ -294,6 +294,8 @@ &usdhc3 {
        pinctrl-0 = <&pinctrl_usdhc3>;
        pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
        pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+       assigned-clocks = <&clk IMX8MM_CLK_USDHC3>;
+       assigned-clock-rates = <400000000>;
        bus-width = <8>;
        non-removable;
        status = "okay";
--
Quoted 3 lines

2.48.1

Hi Adam,

This caught my interest. Where in the IMX8MMRM do you see this and would it also apply to the IMX8MP? (You've patched your IMX8MM and IMX8MN boards).

Have you encountered any issues when running eMMC at HS400 due to this or is it just something you noticed in the RM more recently like with my recent patch that lowers SPI clock due to an obscure RM note [1]

Best Regards,

Tim
[1] https://patchwork.kernel.org/project/linux-arm-kernel/list/?series=965976&archive=both

author
#4 lore raw
Quoted 33 lines · Tim Harvey
Quoted 25 lines · Adam Ford

The reference manual for the i.MX8MM states the clock rate in MMC mode is 1/2 of the input clock, therefore to properly run at HS400 rates, the input clock must be 400MHz to operate at 200MHz. Currently the clock is set to 200MHz which is half the rate it should be, so the throughput is half of what it should be for HS400 operation.

Fixes 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi +2 -1
index 21bcd82fd092..8287a7f66ed3 100644
@@ -294,6 +294,8 @@ &usdhc3 {
        pinctrl-0 = <&pinctrl_usdhc3>;
        pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
        pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+       assigned-clocks = <&clk IMX8MM_CLK_USDHC3>;
+       assigned-clock-rates = <400000000>;
        bus-width = <8>;
        non-removable;
        status = "okay";
--
Quoted 3 lines

2.48.1

Hi Adam,

Quoted 3 lines

This caught my interest. Where in the IMX8MMRM do you see this and would it also apply to the IMX8MP? (You've patched your IMX8MM and IMX8MN boards).

My 8MP board already appears to be running at 400MHz, but I did check. The reference I found was in the 8MM TRM, under 10.3.3.5 Clock generator, there is a note:

CLK is different for the SDR and DDR modes.
- In the SDR mode, CLK is equal to the internal working clock (card_clk).
- In the DDR mode, CLK is equal to card_clk/2.

Quoted 3 lines

Have you encountered any issues when running eMMC at HS400 due to this or is it just something you noticed in the RM more recently like with

One of my colleagues reported that the eMMC was running slower than he expected, and I looked at the reference clock and noticed the 200MHz. He asked if it needed to run 2x that since HS400 clocks on both edges. I looked it up and found the note from above. When I increased the rate to 400MHz from 200MHz, the throughput doubled. I also noticed some other boards, including the reference from NXP had the clock rate set to 400MHz, so I don't think anything unreasonable.

adam

Quoted 6 lines

my recent patch that lowers SPI clock due to an obscure RM note [1]

Best Regards,

Tim
[1] https://patchwork.kernel.org/project/linux-arm-kernel/list/?series=965976&archive=both

#5 lore raw
Quoted 51 lines · Adam Ford
Quoted 33 lines · Tim Harvey
Quoted 25 lines · Adam Ford

The reference manual for the i.MX8MM states the clock rate in MMC mode is 1/2 of the input clock, therefore to properly run at HS400 rates, the input clock must be 400MHz to operate at 200MHz. Currently the clock is set to 200MHz which is half the rate it should be, so the throughput is half of what it should be for HS400 operation.

Fixes 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi +2 -1
index 21bcd82fd092..8287a7f66ed3 100644
@@ -294,6 +294,8 @@ &usdhc3 {
        pinctrl-0 = <&pinctrl_usdhc3>;
        pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
        pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+       assigned-clocks = <&clk IMX8MM_CLK_USDHC3>;
+       assigned-clock-rates = <400000000>;
        bus-width = <8>;
        non-removable;
        status = "okay";
--
Quoted 3 lines

2.48.1

Hi Adam,

Quoted 3 lines

This caught my interest. Where in the IMX8MMRM do you see this and would it also apply to the IMX8MP? (You've patched your IMX8MM and IMX8MN boards).

My 8MP board already appears to be running at 400MHz, but I did check. The reference I found was in the 8MM TRM, under 10.3.3.5 Clock generator, there is a note:

CLK is different for the SDR and DDR modes.
- In the SDR mode, CLK is equal to the internal working clock (card_clk).
- In the DDR mode, CLK is equal to card_clk/2.

Quoted 3 lines

Have you encountered any issues when running eMMC at HS400 due to this or is it just something you noticed in the RM more recently like with

Quoted 8 lines

One of my colleagues reported that the eMMC was running slower than he expected, and I looked at the reference clock and noticed the 200MHz. He asked if it needed to run 2x that since HS400 clocks on both edges. I looked it up and found the note from above. When I increased the rate to 400MHz from 200MHz, the throughput doubled. I also noticed some other boards, including the reference from NXP had the clock rate set to 400MHz, so I don't think anything unreasonable.

Hi Adam,

The verbiage in the 'clock generator' section is not really easy to understand but you're right, setting it to 400MHz also bumped the performance on my boards. It looks like there are a lot of imx8m boards that could likely benefit from this that are not already doing so.

Check your imx8mp again, in my case (imx8mp-venice) sdhc3 was not running at 400Mhz without the appropriate change - maybe yours is running higher due to some other clock configuration you have.

I'll be patching my boards with this as well - thanks!

Best Regards,

Tim

author
#6 lore raw
In reply to Adam Ford
Quoted 8 lines · Adam Ford

The reference manual for the i.MX8MM states the clock rate in MMC mode is 1/2 of the input clock, therefore to properly run at HS400 rates, the input clock must be 400MHz to operate at 200MHz. Currently the clock is set to 200MHz which is half the rate it should be, so the throughput is half of what it should be for HS400 operation.

Shawn and/or Fabio,

Any chance this can get reviewed and possibly applied for the next kernel?

thank you,

adam

Quoted 19 lines
Fixes 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi +2 -1
index 21bcd82fd092..8287a7f66ed3 100644
@@ -294,6 +294,8 @@ &usdhc3 {
        pinctrl-0 = <&pinctrl_usdhc3>;
        pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
        pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+       assigned-clocks = <&clk IMX8MM_CLK_USDHC3>;
+       assigned-clock-rates = <400000000>;
        bus-width = <8>;
        non-removable;
        status = "okay";
--

2.48.1

reviewer Reviewed-by on v1 1/2
#7 lore raw
In reply to Adam Ford
Quoted 10 lines · Adam Ford

The reference manual for the i.MX8MM states the clock rate in MMC mode is 1/2 of the input clock, therefore to properly run at HS400 rates, the input clock must be 400MHz to operate at 200MHz. Currently the clock is set to 200MHz which is half the rate it should be, so the throughput is half of what it should be for HS400 operation.

Fixes 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Applied
#8 lore raw
In reply to Adam Ford
Quoted 9 lines · Adam Ford

The reference manual for the i.MX8MM states the clock rate in MMC mode is 1/2 of the input clock, therefore to properly run at HS400 rates, the input clock must be 400MHz to operate at 200MHz. Currently the clock is set to 200MHz which is half the rate it should be, so the throughput is half of what it should be for HS400 operation.

Fixes 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")

Applied both, thanks!