spacemit: introduce P1 PMIC support
Subsystems (6)
v5 cover spacemit: introduce P1 PMIC support
The SpacemiT P1 is an I2C-controlled PMIC that implements 6 buck converters and 12 LDOs. It contains a load switch, ADC channels, GPIOs, a real-time clock, and a watchdog timer.
This series introduces a multifunction driver for the P1 PMIC as well as drivers for its regulators and RTC.
This version updates the RTC code in patch 4 based on a few review comments from Alexandre Belloni.
-Alex
This series is available here:
https://github.com/riscstar/linux/tree/outgoing/pmic-v5
Between version 4 and version 5:
- Only check the seconds register for change when looping on read
- Return without re-enabling the RTC if writing registers fails
- If the RTC is disabled when reading, return an error
Here is version 4 of this series:
https://lore.kernel.org/lkml/[email protected]/
More complete history is available at that link.
Alex Elder (7):
dt-bindings: mfd: add support the SpacemiT P1 PMIC
mfd: simple-mfd-i2c: add SpacemiT P1 support
regulator: spacemit: support SpacemiT P1 regulators
rtc: spacemit: support the SpacemiT P1 RTC
riscv: dts: spacemit: enable the i2c8 adapter
riscv: dts: spacemit: define fixed regulators
riscv: dts: spacemit: define regulator constraints
.../devicetree/bindings/mfd/spacemit,p1.yaml | 86 +++++++++ .../boot/dts/spacemit/k1-bananapi-f3.dts | 138 +++++++++++++++ arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi | 7 + arch/riscv/boot/dts/spacemit/k1.dtsi | 11 ++ drivers/mfd/Kconfig | 11 ++ drivers/mfd/simple-mfd-i2c.c | 18 ++ drivers/regulator/Kconfig | 12 ++ drivers/regulator/Makefile | 1 + drivers/regulator/spacemit-p1.c | 157 ++++++++++++++++ drivers/rtc/Kconfig | 10 ++ drivers/rtc/Makefile | 1 + drivers/rtc/rtc-spacemit-p1.c | 167 ++++++++++++++++++ 12 files changed, 619 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/spacemit,p1.yaml create mode 100644 drivers/regulator/spacemit-p1.c create mode 100644 drivers/rtc/rtc-spacemit-p1.c
base-commit: ecb259c4f70dd5c83907809f45bf4dc6869961d7
Signature · 1 line
2.45.2
PATCH v5 1/7 dt-bindings: mfd: add support the SpacemiT P1 PMIC
Enable the SpacemiT P1, which is an I2C-controlled PMIC. Initially only the RTC and regulators will be supported.
--- .../devicetree/bindings/mfd/spacemit,p1.yaml | 86 +++++++++++++++++++ 1 file changed, 86 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/spacemit,p1.yaml
Documentation/devicetree/bindings/mfd/spacemit,p1.yaml new file +86 -0
@@ -0,0 +1,86 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/spacemit,p1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SpacemiT P1 Power Management Integrated Circuit + +maintainers: + - Troy Mitchell <[email protected]> + +description: + P1 is an I2C-controlled PMIC produced by SpacemiT. It implements six + constant-on-time buck converters and twelve low-dropout regulators. + It also contains a load switch, watchdog timer, real-time clock, eight + 12-bit ADC channels, and six GPIOs. Additional details are available + in the "Power Stone/P1" section at the following link. + https://developer.spacemit.com/documentation + +properties: + compatible: + const: spacemit,p1 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vin-supply: + description: Input supply phandle. + + regulators: + type: object + + patternProperties: + "^(buck[1-6]|aldo[1-4]|dldo[1-7])$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@41 { + compatible = "spacemit,p1"; + reg = <0x41>; + interrupts = <64>; + + regulators { + buck1 { + regulator-name = "buck1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3450000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + aldo1 { + regulator-name = "aldo1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + }; + + dldo1 { + regulator-name = "dldo1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + }; + }; + }; + };
Signature · 1 line
2.45.2
Re: [PATCH v5 1/7] dt-bindings: mfd: add support the SpacemiT P1 PMIC
Quoted 9 lines · Alex Elder
Enable the SpacemiT P1, which is an I2C-controlled PMIC. Initially only the RTC and regulators will be supported.
Signed-off-by Alex Elder <[email protected]>--- .../devicetree/bindings/mfd/spacemit,p1.yaml | 86 +++++++++++++++++++ 1 file changed, 86 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/spacemit,p1.yaml
PATCH v5 2/7 mfd: simple-mfd-i2c: add SpacemiT P1 support
In reply to Alex ElderEnable support for the RTC and regulators found in the SpacemiT P1 PMIC. Support is implemented by the simple I2C MFD driver.
The P1 PMIC is normally implemented with the SpacemiT K1 SoC. This PMIC provides 6 buck converters and 12 LDO regulators. It also implements a switch, watchdog timer, real-time clock, and more. Initially its RTC and regulators are supported.
--- drivers/mfd/Kconfig | 11 +++++++++++ drivers/mfd/simple-mfd-i2c.c | 18 ++++++++++++++++++ 2 files changed, 29 insertions(+)
drivers/mfd/Kconfig +11 -0
@@ -1182,6 +1182,17 @@ config MFD_QCOM_RPM Say M here if you want to include support for the Qualcomm RPM as a module. This will build a module called "qcom_rpm". +config MFD_SPACEMIT_P1 + tristate "SpacemiT P1 PMIC" + depends on I2C + select MFD_SIMPLE_MFD_I2C + help + This option supports the I2C-based SpacemiT P1 PMIC, which + contains regulators, a power switch, GPIOs, an RTC, and more. + This option is selected when any of the supported sub-devices + is configured. The basic functionality is implemented by the + simple MFD I2C driver. + config MFD_SPMI_PMIC tristate "Qualcomm SPMI PMICs" depends on ARCH_QCOM || COMPILE_TEST
drivers/mfd/simple-mfd-i2c.c +18 -0
@@ -93,12 +93,30 @@ static const struct simple_mfd_data maxim_mon_max77705 = { .mfd_cell_size = ARRAY_SIZE(max77705_sensor_cells), }; +static const struct regmap_config spacemit_p1_regmap_config = { + .reg_bits =8 , + .val_bits =8 , + .max_register =0xaa , +}; + +static const struct mfd_cell spacemit_p1_cells[] = { + { .name ="spacemit-p1-regulator" , }, + { .name ="spacemit-p1-rtc" , }, +}; + +static const struct simple_mfd_data spacemit_p1 = { + .regmap_config = &spacemit_p1_regmap_config, + .mfd_cell = spacemit_p1_cells, + .mfd_cell_size =ARRAY_SIZE (spacemit_p1_cells), +}; +static const struct of_device_id simple_mfd_i2c_of_match[] = { { .compatible ="kontron,sl28cpld" }, { .compatible ="silergy,sy7636a" , .data = &silergy_sy7636a}, { .compatible ="maxim,max5970" , .data = &maxim_max5970}, { .compatible ="maxim,max5978" , .data = &maxim_max5970}, { .compatible ="maxim,max77705-battery" , .data = &maxim_mon_max77705}, + { .compatible ="spacemit,p1" , .data = &spacemit_p1, }, {} };MODULE_DEVICE_TABLE (of, simple_mfd_i2c_of_match);
Signature · 1 line
2.45.2
PATCH v5 3/7 regulator: spacemit: support SpacemiT P1 regulators
In reply to Alex ElderAdd support for the regulators found in the SpacemiT P1 PMIC. This PMIC provides 6 buck converters and 12 LDO regulators.
The PMIC is implemented as a multi-function device. These regulators are probed based on this driver being named in a MFD cell in the simple MFD I2C driver.
--- drivers/regulator/Kconfig | 12 +++ drivers/regulator/Makefile | 1 + drivers/regulator/spacemit-p1.c | 157 ++++++++++++++++++++++++++++++++ 3 files changed, 170 insertions(+) create mode 100644 drivers/regulator/spacemit-p1.c
drivers/regulator/Kconfig +12 -0
@@ -1395,6 +1395,18 @@ config REGULATOR_SLG51000 The SLG51000 is seven compact and customizable low dropout regulators. +config REGULATOR_SPACEMIT_P1 + tristate "SpacemiT P1 regulators" + depends on ARCH_SPACEMIT || COMPILE_TEST + select MFD_SPACEMIT_P1 + default ARCH_SPACEMIT + help + Enable support for regulators implemented by the SpacemiT P1 + power controller. The P1 implements 6 high-efficiency buck + converters and 12 programmable LDO regulators. To compile this + driver as a module, choose M here. The module will be called + "spacemit-pmic". + config REGULATOR_STM32_BOOSTER tristate "STMicroelectronics STM32 BOOSTER" depends on ARCH_STM32 || COMPILE_TEST
drivers/regulator/Makefile +1 -0
@@ -162,6 +162,7 @@ obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o obj-$(CONFIG_REGULATOR_SC2731) += sc2731-regulator.o obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o obj-$(CONFIG_REGULATOR_SLG51000) += slg51000-regulator.o +obj-$(CONFIG_REGULATOR_SPACEMIT_P1) += spacemit-p1.o obj-$(CONFIG_REGULATOR_STM32_BOOSTER) += stm32-booster.o obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o obj-$(CONFIG_REGULATOR_STM32_PWR) += stm32-pwr.o
drivers/regulator/spacemit-p1.c new file +157 -0
157 lines not on this page · raw message
Signature · 1 line
2.45.2
PATCH v5 4/7 rtc: spacemit: support the SpacemiT P1 RTC
In reply to Alex ElderAdd support for the RTC found in the SpacemiT P1 PMIC. Initially only setting and reading the time are supported.
The PMIC is implemented as a multi-function device. This RTC is probed based on this driver being named in a MFD cell in the simple MFD I2C driver.
---
v5: - Only check the seconds register for change when looping on read
- Return without re-enabling the RTC if writing registers fails
- If the RTC is disabled when reading, return an error
drivers/rtc/Kconfig | 10 ++ drivers/rtc/Makefile | 1 + drivers/rtc/rtc-spacemit-p1.c | 167 ++++++++++++++++++++++++++++++++++ 3 files changed, 178 insertions(+) create mode 100644 drivers/rtc/rtc-spacemit-p1.c
drivers/rtc/Kconfig +10 -0
@@ -406,6 +406,16 @@ config RTC_DRV_MAX77686 This driver can also be built as a module. If so, the module will be called rtc-max77686. +config RTC_DRV_SPACEMIT_P1 + tristate "SpacemiT P1 RTC" + depends on ARCH_SPACEMIT || COMPILE_TEST + select MFD_SPACEMIT_P1 + default ARCH_SPACEMIT + help + Enable support for the RTC function in the SpacemiT P1 PMIC. + This driver can also be built as a module, which will be called + "spacemit-p1-rtc". + config RTC_DRV_NCT3018Y tristate "Nuvoton NCT3018Y" depends on OF
drivers/rtc/Makefile +1 -0
@@ -171,6 +171,7 @@ obj-$(CONFIG_RTC_DRV_SD2405AL) += rtc-sd2405al.o obj-$(CONFIG_RTC_DRV_SD3078) += rtc-sd3078.o obj-$(CONFIG_RTC_DRV_SH) += rtc-sh.o obj-$(CONFIG_RTC_DRV_SNVS) += rtc-snvs.o +obj-$(CONFIG_RTC_DRV_SPACEMIT_P1) += rtc-spacemit-p1.o obj-$(CONFIG_RTC_DRV_SPEAR) += rtc-spear.o obj-$(CONFIG_RTC_DRV_STARFIRE) += rtc-starfire.o obj-$(CONFIG_RTC_DRV_STK17TA8) += rtc-stk17ta8.o
drivers/rtc/rtc-spacemit-p1.c new file +167 -0
167 lines not on this page · raw message
Signature · 1 line
2.45.2
PATCH v5 5/7 riscv: dts: spacemit: enable the i2c8 adapter
In reply to Alex ElderDefine properties for the I2C adapter that provides access to the SpacemiT P1 PMIC. Enable this adapter on the Banana Pi BPI-F3.
--- arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts | 15 +++++++++++++++ arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi | 7 +++++++ arch/riscv/boot/dts/spacemit/k1.dtsi | 11 +++++++++++ 3 files changed, 33 insertions(+)
arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts +15 -0
@@ -40,6 +40,21 @@ &emmc { status = "okay"; }; +&i2c8 { + pinctrl-0 = <&i2c8_cfg>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + pmic@41 { + compatible = "spacemit,p1"; + reg = <0x41>; + interrupts = <64>; + status = "okay"; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_2_cfg>;
arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi +7 -0
@@ -11,6 +11,13 @@ #define K1_GPIO(x) (x / 32) (x % 32) &pinctrl { + i2c8_cfg: i2c8-cfg { + i2c8-0-pins { + pinmux = <K1_PADCONF(93, 0)>, /* PWR_SCL */ + <K1_PADCONF(94, 0)>; /* PWR_SDA */ + }; + }; + uart0_2_cfg: uart0-2-cfg { uart0-2-pins { pinmux = <K1_PADCONF(68, 2)>,
arch/riscv/boot/dts/spacemit/k1.dtsi +11 -0
@@ -483,6 +483,17 @@ gpio: gpio@d4019000 { <&pinctrl 3 0 96 32>; }; + i2c8: i2c@d401d800 { + compatible = "spacemit,k1-i2c"; + reg = <0x0 0xd401d800 0x0 0x38>; + interrupts = <19>; + clocks = <&syscon_apbc CLK_TWSI8>, + <&syscon_apbc CLK_TWSI8_BUS>; + clock-names = "func", "bus"; + clock-frequency = <400000>; + status = "disabled"; + }; + pinctrl: pinctrl@d401e000 { compatible = "spacemit,k1-pinctrl"; reg = <0x0 0xd401e000 0x0 0x400>;
Signature · 1 line
2.45.2
PATCH v5 6/7 riscv: dts: spacemit: define fixed regulators
In reply to Alex ElderDefine the DC power input and the 4v power as fixed supplies in the Banana Pi BPI-F3.
--- .../boot/dts/spacemit/k1-bananapi-f3.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts +19 -0
@@ -28,6 +28,25 @@ led1 { default-state = "on"; }; }; + + reg_dc_in: dc-in-12v { + compatible = "regulator-fixed"; + regulator-name = "dc_in_12v"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vcc_4v: vcc-4v { + compatible = "regulator-fixed"; + regulator-name = "vcc_4v"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <4000000>; + regulator-boot-on; + regulator-always-on; + vin-supply = <®_dc_in>; + }; }; &emmc {
Signature · 1 line
2.45.2
PATCH v5 7/7 riscv: dts: spacemit: define regulator constraints
In reply to Alex ElderDefine basic constraints for the regulators in the SpacemiT P1 PMIC, as implemented in the Banana Pi BPI-F3.
--- .../boot/dts/spacemit/k1-bananapi-f3.dts | 104 ++++++++++++++++++ 1 file changed, 104 insertions(+)
arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts +104 -0
@@ -70,7 +70,111 @@ pmic@41 { compatible = "spacemit,p1"; reg = <0x41>; interrupts = <64>; + vin-supply = <®_vcc_4v>; status = "okay"; + + regulators { + buck1 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3450000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + buck2 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3450000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + buck3 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1800000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + buck4 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3300000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + buck5 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3450000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + buck6 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3450000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + aldo1 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + }; + + aldo2 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + + aldo3 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + + aldo4 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + + dldo1 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + }; + + dldo2 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + + dldo3 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + + dldo4 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-always-on; + }; + + dldo5 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + + dldo6 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-always-on; + }; + + dldo7 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + }; }; };
Signature · 1 line
2.45.2