dt-bindings: mtd: convert lpc32xx-slc.txt to yaml format
Subsystems (4)
Frank Li
maintainerPATCH 1/1 dt-bindings: mtd: convert lpc32xx-slc.txt to yaml format
Convert lpc32xx-slc.txt to yaml format.
Additional changes:
- add ref to nand-controller.yaml
Signed-off-by Frank Li <[email protected]>
--- .../devicetree/bindings/mtd/lpc32xx-slc.txt | 52 --------- .../bindings/mtd/nxp,lpc3220-slc.yaml | 101 ++++++++++++++++++ 2 files changed, 101 insertions(+), 52 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt create mode 100644 Documentation/devicetree/bindings/mtd/nxp,lpc3220-slc.yaml
Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt deleted +0 -52
@@ -1,52 +0,0 @@ -NXP LPC32xx SoC NAND SLC controller - -Required properties: -- compatible: "nxp,lpc3220-slc" -- reg: Address and size of the controller -- nand-on-flash-bbt: Use bad block table on flash -- gpios: GPIO specification for NAND write protect - -The following required properties are very controller specific. See the LPC32xx -User Manual: -- nxp,wdr-clks: Delay before Ready signal is tested on write (W_RDY) -- nxp,rdr-clks: Delay before Ready signal is tested on read (R_RDY) -(The following values are specified in Hz, to make them independent of actual -clock speed:) -- nxp,wwidth: Write pulse width (W_WIDTH) -- nxp,whold: Write hold time (W_HOLD) -- nxp,wsetup: Write setup time (W_SETUP) -- nxp,rwidth: Read pulse width (R_WIDTH) -- nxp,rhold: Read hold time (R_HOLD) -- nxp,rsetup: Read setup time (R_SETUP) - -Optional subnodes: -- Partitions, see Documentation/devicetree/bindings/mtd/mtd.yaml - -Example: - - slc: flash@20020000 { - compatible = "nxp,lpc3220-slc"; - reg = <0x20020000 0x1000>; - #address-cells = <1>; - #size-cells = <1>; - - nxp,wdr-clks = <14>; - nxp,wwidth = <40000000>; - nxp,whold = <100000000>; - nxp,wsetup = <100000000>; - nxp,rdr-clks = <14>; - nxp,rwidth = <40000000>; - nxp,rhold = <66666666>; - nxp,rsetup = <100000000>; - nand-on-flash-bbt; - gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ - - mtd0@00000000 { - label = "phy3250-boot"; - reg = <0x00000000 0x00064000>; - read-only; - }; - - ... - - };
Documentation/devicetree/bindings/mtd/nxp,lpc3220-slc.yaml new file +101 -0
101 lines not on this page · raw message
Signature · 1 line
2.34.1
Rob Herring
maintainerQuoted 98 lines · Frank Li
Convert lpc32xx-slc.txt to yaml format.
Additional changes:
- add ref tonand-controller.yamlSigned-off-by Frank Li <[email protected]>--- .../devicetree/bindings/mtd/lpc32xx-slc.txt | 52 --------- .../bindings/mtd/nxp,lpc3220-slc.yaml | 101 ++++++++++++++++++ 2 files changed, 101 insertions(+), 52 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt create mode 100644 Documentation/devicetree/bindings/mtd/nxp,lpc3220-slc.yamlDocumentation/devicetree/bindings/mtd/lpc32xx-slc.txt deleted +0
-52@@ -1,52 +0,0 @@ -NXP LPC32xx SoC NAND SLC controller - -Required properties: -- compatible: "nxp,lpc3220-slc" -- reg: Address and size of the controller -- nand-on-flash-bbt: Use bad block table on flash -- gpios: GPIO specification for NAND write protect - -The following required properties are very controller specific. See the LPC32xx -User Manual: -- nxp,wdr-clks: Delay before Ready signal is tested on write (W_RDY) -- nxp,rdr-clks: Delay before Ready signal is tested on read (R_RDY) -(The following values are specified in Hz, to make them independent of actual -clock speed:) -- nxp,wwidth: Write pulse width (W_WIDTH) -- nxp,whold: Write hold time (W_HOLD) -- nxp,wsetup: Write setup time (W_SETUP) -- nxp,rwidth: Read pulse width (R_WIDTH) -- nxp,rhold: Read hold time (R_HOLD) -- nxp,rsetup: Read setup time (R_SETUP) - -Optional subnodes: -- Partitions, see Documentation/devicetree/bindings/mtd/mtd.yaml - -Example: - - slc: flash@20020000 { - compatible = "nxp,lpc3220-slc"; - reg = <0x20020000 0x1000>; - #address-cells = <1>; - #size-cells = <1>; - - nxp,wdr-clks = <14>; - nxp,wwidth = <40000000>; - nxp,whold = <100000000>; - nxp,wsetup = <100000000>; - nxp,rdr-clks = <14>; - nxp,rwidth = <40000000>; - nxp,rhold = <66666666>; - nxp,rsetup = <100000000>; - nand-on-flash-bbt; - gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ - - mtd0@00000000 { - label = "phy3250-boot"; - reg = <0x00000000 0x00064000>; - read-only; - }; - - ... - - };Documentation/devicetree/bindings/mtd/nxp,lpc3220-slc.yaml new file +21
-0@@ -0,0 +1,101 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/nxp,lpc3220-slc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP LPC32xx SoC NAND SLC controller + +maintainers: + - Frank Li <[email protected]> + +properties: + compatible: + const: nxp,lpc3220-slc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 +
Documentation/devicetree/bindings/mtd/nxp,lpc3220-slc.yaml line 31
Quoted 10 lines
Documentation/devicetree/bindings/mtd/nxp,lpc3220-slc.yaml new file +10
-0+ gpios: + maxItems: 1 + description: + GPIO specification for NAND write protect + + nand-on-flash-bbt: true + + partitions: + type: object + $ref: partitions/partition.yaml
That's not right... You want partitions.yaml?
Quoted 73 lines
Documentation/devicetree/bindings/mtd/nxp,lpc3220-slc.yaml new file +70
-0+ unevaluatedProperties: false + + nxp,wdr-clks: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Delay before Ready signal is tested on write (W_RDY) + + nxp,rdr-clks: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Delay before Ready signal is tested on read (R_RDY) + + nxp,wwidth: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Write pulse width (W_WIDTH) in Hz + + nxp,whold: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Write hold time (W_HOLD) in Hz + + nxp,wsetup: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Write setup time (W_SETUP) in Hz + + nxp,rwidth: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Read pulse width (R_WIDTH) in Hz + + nxp,rhold: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Read hold time (R_HOLD) in Hz + + nxp,rsetup: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Read setup time (R_SETUP) in Hz + +required: + - compatible + - reg + - gpios + +allOf: + - $ref: nand-controller.yaml + +unevaluatedProperties: false + +examples: + - | + nand-controller@20020000 { + compatible = "nxp,lpc3220-slc"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x20020000 0x1000>; + nxp,wdr-clks = <14>; + nxp,wwidth = <40000000>; + nxp,whold = <100000000>; + nxp,wsetup = <100000000>; + nxp,rdr-clks = <14>; + nxp,rwidth = <40000000>; + nxp,rhold = <66666666>; + nxp,rsetup = <100000000>; + nand-on-flash-bbt; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + };Signature · 1 line
2.34.1