arm64: allwinner: t527: Add OrangePi 4A board
Subsystems (2)
Chen-Yu Tsai
maintainerv3 cover arm64: allwinner: t527: Add OrangePi 4A board
From: Chen-Yu Tsai <[email protected]>
Hi everyone,
This is v3 of my OrangePi 4A series.
Changes since v2:
- Actually include cpusldo regulator name change and axp323 aldo1/dldo1 comments
- Fix indentation of comment in usb_otg block
- Link to v2:
https://lore.kernel.org/all/[email protected]/
Changes since v1:
- Fixed regulator names for bldo3 and bldo4
- Dropped labels for aldo1, bldo3, and bldo4, which are not really used
- Added voltage constraints to aldo2, based on specifications from schematic
- Appended "-usb-0v9" to cpusldo's regulator name
- Added comments to explain how axp323 aldo1 and dldo1 are tied together
- Link to v1:
https://lore.kernel.org/all/[email protected]/
This series adds support for the OrangePi 4A board. This is a Raspberry Pi model B form factor development board based on the Allwinner T527 SoC.
The board has the following features:
- Allwinner T527 SoC
- AXP717B + AXP323 PMICs
- Up to 4GB LPDDR4 DRAM
- micro SD slot
- optional eMMC module
- M.2 slot for PCIe 2.0 x1
- 16 MB SPI-NOR flash
- 4x USB 2.0 type-A ports (one can be used in gadget mode)
- 1x Gigabit ethernet w/ Motorcomm PHY (through yet to be supported GMAC200)
- 3.5mm audio jack via internal audio codec
- HDMI 2.0 output
- eDP, MIPI CSI (2-lane and 4-lane) and MIPI DSI (4-lane) connectors
- USB type-C port purely for power
- AP6256 (Broadcom BCM4345) WiFi 5.0 + BT 5.0
- unsoldered headers for ADC and an additional USB 2.0 host port
- 40-pin GPIO header
Patch 1 adds a new entry to the list of board compatibles.
Patch 2 and 3 are minor cleanups.
Patch 4 adds pins for UART1, which is used for BT on the board.
Patch 5 adds a dts file for the new board.
Please take a look. I will take all the patches through the sunxi tree.
Thanks
ChenYu
Chen-Yu Tsai (5):
dt-bindings: arm: sunxi: Add Xunlong OrangePi 4A board
arm64: dts: allwinner: a523: Move mmc nodes to correct position
arm64: dts: allwinner: a523: Move rgmii0 pins to correct location
arm64: dts: allwinner: a523: Add UART1 pins
arm64: dts: allwinner: t527: Add OrangePi 4A board
.../devicetree/bindings/arm/sunxi.yaml | 5 + arch/arm64/boot/dts/allwinner/Makefile | 1 + .../arm64/boot/dts/allwinner/sun55i-a523.dtsi | 160 ++++---- .../dts/allwinner/sun55i-t527-orangepi-4a.dts | 385 ++++++++++++++++++ 4 files changed, 478 insertions(+), 73 deletions(-) create mode 100644 arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
Signature · 1 line
2.39.5
Chen-Yu Tsai
maintainerPATCH v3 1/5 dt-bindings: arm: sunxi: Add Xunlong OrangePi 4A board
From: Chen-Yu Tsai <[email protected]>
The OrangePi 4A is a typical Raspberry Pi model B sized development board from Xunlong designed around an Allwinner T527 SoC.
Add its compatible name to the list of valid ones.
--- Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++ 1 file changed, 5 insertions(+)
Documentation/devicetree/bindings/arm/sunxi.yaml +5 -0
@@ -996,6 +996,11 @@ properties: - const: xunlong,orangepi-3 - const: allwinner,sun50i-h6 + - description: Xunlong OrangePi 4A + items: + - const: xunlong,orangepi-4a + - const: allwinner,sun55i-t527 + - description: Xunlong OrangePi Lite items: - const: xunlong,orangepi-lite
Signature · 1 line
2.39.5
Chen-Yu Tsai
maintainerPATCH v3 2/5 arm64: dts: allwinner: a523: Move mmc nodes to correct position
In reply to Chen-Yu TsaiFrom: Chen-Yu Tsai <[email protected]>
When the mmc nodes were added to the dtsi file, they were inserted in the incorrect position.
Move them to the correct place.
--- .../arm64/boot/dts/allwinner/sun55i-a523.dtsi | 126 +++++++++--------- 1 file changed, 63 insertions(+), 63 deletions(-)
arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi +63 -63
@@ -181,69 +181,6 @@ ccu: clock-controller@2001000 { #reset-cells = <1>; }; - mmc0: mmc@4020000 { - compatible = "allwinner,sun55i-a523-mmc", - "allwinner,sun20i-d1-mmc"; - reg = <0x04020000 0x1000>; - clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>; - clock-names = "ahb", "mmc"; - resets = <&ccu RST_BUS_MMC0>; - reset-names = "ahb"; - interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins>; - status = "disabled"; - - max-frequency = <150000000>; - cap-sd-highspeed; - cap-mmc-highspeed; - cap-sdio-irq; - #address-cells = <1>; - #size-cells = <0>; - }; - - mmc1: mmc@4021000 { - compatible = "allwinner,sun55i-a523-mmc", - "allwinner,sun20i-d1-mmc"; - reg = <0x04021000 0x1000>; - clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>; - clock-names = "ahb", "mmc"; - resets = <&ccu RST_BUS_MMC1>; - reset-names = "ahb"; - interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins>; - status = "disabled"; - - max-frequency = <150000000>; - cap-sd-highspeed; - cap-mmc-highspeed; - cap-sdio-irq; - #address-cells = <1>; - #size-cells = <0>; - }; - - mmc2: mmc@4022000 { - compatible = "allwinner,sun55i-a523-mmc", - "allwinner,sun20i-d1-mmc"; - reg = <0x04022000 0x1000>; - clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>; - clock-names = "ahb", "mmc"; - resets = <&ccu RST_BUS_MMC2>; - reset-names = "ahb"; - interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&mmc2_pins>; - status = "disabled"; - - max-frequency = <150000000>; - cap-sd-highspeed; - cap-mmc-highspeed; - cap-sdio-irq; - #address-cells = <1>; - #size-cells = <0>; - }; - wdt: watchdog@2050000 { compatible = "allwinner,sun55i-a523-wdt"; reg = <0x2050000 0x20>;
@@ -449,6 +386,69 @@ its: msi-controller@3440000 { }; }; + mmc0: mmc@4020000 { + compatible = "allwinner,sun55i-a523-mmc", + "allwinner,sun20i-d1-mmc"; + reg = <0x04020000 0x1000>; + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC0>; + reset-names = "ahb"; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + status = "disabled"; + + max-frequency = <150000000>; + cap-sd-highspeed; + cap-mmc-highspeed; + cap-sdio-irq; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc1: mmc@4021000 { + compatible = "allwinner,sun55i-a523-mmc", + "allwinner,sun20i-d1-mmc"; + reg = <0x04021000 0x1000>; + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC1>; + reset-names = "ahb"; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + status = "disabled"; + + max-frequency = <150000000>; + cap-sd-highspeed; + cap-mmc-highspeed; + cap-sdio-irq; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc2: mmc@4022000 { + compatible = "allwinner,sun55i-a523-mmc", + "allwinner,sun20i-d1-mmc"; + reg = <0x04022000 0x1000>; + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC2>; + reset-names = "ahb"; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + status = "disabled"; + + max-frequency = <150000000>; + cap-sd-highspeed; + cap-mmc-highspeed; + cap-sdio-irq; + #address-cells = <1>; + #size-cells = <0>; + }; + usb_otg: usb@4100000 { compatible = "allwinner,sun55i-a523-musb", "allwinner,sun8i-a33-musb";
Signature · 1 line
2.39.5
Chen-Yu Tsai
maintainerPATCH v3 3/5 arm64: dts: allwinner: a523: Move rgmii0 pins to correct location
In reply to Chen-Yu TsaiFrom: Chen-Yu Tsai <[email protected]>
Nodes are supposed to be sorted by address, or if no addresses apply, by node name. The rgmii0 pins are out of order, possibly due to multiple patches adding pin mux settings conflicting.
Move the rgmii0 pins to the correct location.
--- .../arm64/boot/dts/allwinner/sun55i-a523.dtsi | 20 +++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-)
arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi +10 -10
@@ -126,16 +126,6 @@ pio: pinctrl@2000000 { interrupt-controller; #interrupt-cells = <3>; - rgmii0_pins: rgmii0-pins { - pins = "PH0", "PH1", "PH2", "PH3", "PH4", - "PH5", "PH6", "PH7", "PH9", "PH10", - "PH14", "PH15", "PH16", "PH17", "PH18"; - allwinner,pinmux = <5>; - function = "gmac0"; - drive-strength = <40>; - bias-disable; - }; - mmc0_pins: mmc0-pins { pins = "PF0" ,"PF1", "PF2", "PF3", "PF4", "PF5"; allwinner,pinmux = <2>;
@@ -163,6 +153,16 @@ mmc2_pins: mmc2-pins { bias-pull-up; }; + rgmii0_pins: rgmii0-pins { + pins = "PH0", "PH1", "PH2", "PH3", "PH4", + "PH5", "PH6", "PH7", "PH9", "PH10", + "PH14", "PH15", "PH16", "PH17", "PH18"; + allwinner,pinmux = <5>; + function = "gmac0"; + drive-strength = <40>; + bias-disable; + }; + uart0_pb_pins: uart0-pb-pins { pins = "PB9", "PB10"; allwinner,pinmux = <2>;
Signature · 1 line
2.39.5
Chen-Yu Tsai
maintainerPATCH v3 4/5 arm64: dts: allwinner: a523: Add UART1 pins
In reply to Chen-Yu TsaiFrom: Chen-Yu Tsai <[email protected]>
UART1 is normally used to connect to the Bluetooth side of a Broadcom WiFi+BT combo chip. The connection uses 4 pins.
Add pinmux nodes for UART1, one for the RX/TX pins, and one for the RTS/CTS pins.
--- arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi +14 -0
@@ -168,6 +168,20 @@ uart0_pb_pins: uart0-pb-pins { allwinner,pinmux = <2>; function = "uart0"; }; + + /omit-if-no-ref/ + uart1_pins: uart1-pins { + pins = "PG6", "PG7"; + function = "uart1"; + allwinner,pinmux = <2>; + }; + + /omit-if-no-ref/ + uart1_rts_cts_pins: uart1-rts-cts-pins { + pins = "PG8", "PG9"; + function = "uart1"; + allwinner,pinmux = <2>; + }; }; ccu: clock-controller@2001000 {
Signature · 1 line
2.39.5
Chen-Yu Tsai
maintainerPATCH v3 5/5 arm64: dts: allwinner: t527: Add OrangePi 4A board
In reply to Chen-Yu TsaiFrom: Chen-Yu Tsai <[email protected]>
The OrangePi 4A is a typical Raspberry Pi model B sized development board from Xunlong designed around an Allwinner T527 SoC.
The board has the following features:
- Allwinner T527 SoC
- AXP717B + AXP323 PMICs
- Up to 4GB LPDDR4 DRAM
- micro SD slot
- optional eMMC module
- M.2 slot for PCIe 2.0 x1
- 16 MB SPI-NOR flash
- 4x USB 2.0 type-A ports (one can be used in gadget mode)
- 1x Gigabit ethernet w/ Motorcomm PHY (through yet to be supported GMAC200)
- 3.5mm audio jack via internal audio codec
- HDMI 2.0 output
- eDP, MIPI CSI (2-lane and 4-lane) and MIPI DSI (4-lane) connectors
- USB type-C port purely for power
- AP6256 (Broadcom BCM4345) WiFi 5.0 + BT 5.0
- unsoldered headers for ADC and an additional USB 2.0 host port
- 40-pin GPIO header
Add a device tree for it, enabling all peripherals currently supported.
---
Changes since v2:
- Actually include cpusldo regulator name change and axp323 aldo1/dldo1 comments
- Fix indentation of comment in usb_otg block
Changes since v1:
- Fixed regulator names for bldo3 and bldo4
- Dropped labels for aldo1, bldo3, and bldo4, which are not really used
- Added voltage constraints to aldo2, based on specifications from schematic
- Appended "-usb-0v9" to cpusldo's regulator name
- Added comments to explain how axp323 aldo1 and dldo1 are tied together
--- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun55i-t527-orangepi-4a.dts | 385 ++++++++++++++++++ 2 files changed, 386 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
arch/arm64/boot/dts/allwinner/Makefile +1 -0
@@ -57,3 +57,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-sp.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun55i-a527-cubie-a5e.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun55i-h728-x96qpro+.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-avaota-a1.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-orangepi-4a.dtb
arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts new file +385 -0
385 lines not on this page · raw message
Signature · 1 line
2.39.5
Re: [PATCH v3 5/5] arm64: dts: allwinner: t527: Add OrangePi 4A board
On Sun, 29 Jun 2025 00:16:08 +0800
Chen-Yu Tsai <[email protected]> wrote:
Hi,
Quoted 23 lines
From: Chen-Yu Tsai <[email protected]>
The OrangePi 4A is a typical Raspberry Pi model B sized development board from Xunlong designed around an Allwinner T527 SoC.
The board has the following features:
- Allwinner T527 SoC
- AXP717B + AXP323 PMICs
- Up to 4GB LPDDR4 DRAM
- micro SD slot
- optional eMMC module
- M.2 slot for PCIe 2.0 x1
- 16 MB SPI-NOR flash
- 4x USB 2.0 type-A ports (one can be used in gadget mode)
- 1x Gigabit ethernet w/ Motorcomm PHY (through yet to be supported GMAC200)
- 3.5mm audio jack via internal audio codec
- HDMI 2.0 output
- eDP, MIPI CSI (2-lane and 4-lane) and MIPI DSI (4-lane) connectors
- USB type-C port purely for power
- AP6256 (Broadcom BCM4345) WiFi 5.0 + BT 5.0
- unsoldered headers for ADC and an additional USB 2.0 host port
- 40-pin GPIO header
Quoted 1 line
Add a device tree for it, enabling all peripherals currently supported.
Looks good to me now, thanks for the changes!
Quoted 1 line
Signed-off-by Chen-Yu Tsai <[email protected]>
Cheers,
Andre
Quoted 419 lines
---
Changes since v2:
- Actually include cpusldo regulator name change and axp323 aldo1/dldo1 comments
- Fix indentation of comment inusb_otgblockChanges since v1:
- Fixed regulator names for bldo3 and bldo4
- Dropped labels for aldo1, bldo3, and bldo4, which are not really used
- Added voltage constraints to aldo2, based on specifications from schematic
- Appended "-usb-0v9" to cpusldo's regulator name
- Added comments to explain how axp323 aldo1 and dldo1 are tied together--- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun55i-t527-orangepi-4a.dts | 385 ++++++++++++++++++ 2 files changed, 386 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dtsarch/arm64/boot/dts/allwinner/Makefile +1
-0@@ -57,3 +57,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-sp.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun55i-a527-cubie-a5e.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun55i-h728-x96qpro+.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-avaota-a1.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-orangepi-4a.dtbarch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts new file +385
-0@@ -0,0 +1,385 @@ +// SPDX-License-Identifier: (GPL-2.0-only OR MIT) +/* + * Copyright (C) 2025 Chen-Yu Tsai <[email protected]> + */ + +/dts-v1/; + +#include "sun55i-a523.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> + +/ { + model = "OrangePi 4A"; + compatible = "xunlong,orangepi-4a", "allwinner,sun55i-t527"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + ext_osc32k: ext-osc32k-clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "ext_osc32k"; + }; + + leds { + compatible = "gpio-leds"; + + /* PWM capable pin, but PWM isn't supported yet. */ + led { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */ + }; + }; + + wifi_pwrseq: pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 1 1 GPIO_ACTIVE_LOW>; /* PM1 */ + clocks = <&rtc CLK_OSC32K_FANOUT>; + clock-names = "ext_clock"; + }; + + reg_otg_vbus: regulator-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "otg-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <®_vcc5v>; + gpio = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ + enable-active-high; + }; + + reg_pcie_vcc3v3: regulator-pcie-vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc-pcie-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <®_vcc5v>; + gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ + enable-active-high; + }; + + reg_usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <®_vcc5v>; + gpio = <&r_pio 0 12 GPIO_ACTIVE_HIGH>; /* PL12 */ + enable-active-high; + }; + + reg_vcc5v: regulator-vcc5v { + /* board wide 5V supply from USB type-C port */ + compatible = "regulator-fixed"; + regulator-name = "vcc-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&mmc0 { + vmmc-supply = <®_cldo3>; + cd-gpios = <&pio 5 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PF6 */ + bus-width = <4>; + status = "okay"; +}; + +&mmc1 { + bus-width = <4>; + mmc-pwrseq = <&wifi_pwrseq>; + non-removable; + vmmc-supply = <®_dldo1_323>; + vqmmc-supply = <®_bldo1>; + status = "okay"; + + brcmf: wifi@1 { + compatible = "brcm,bcm4329-fmac"; + reg = <1>; + interrupt-parent = <&r_pio>; + interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */ + interrupt-names = "host-wake"; + }; +}; + +&mmc2 { + bus-width = <8>; + cap-mmc-hw-reset; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + non-removable; + vmmc-supply = <®_cldo3>; + vqmmc-supply = <®_cldo1>; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&pio { + vcc-pb-supply = <®_cldo3>; /* via VCC-IO */ + vcc-pc-supply = <®_cldo1>; + vcc-pd-supply = <®_cldo3>; + vcc-pe-supply = <®_aldo2>; + vcc-pf-supply = <®_cldo3>; /* VCC-IO for 3.3v; VCC-MCSI for 1.8v */ + vcc-pg-supply = <®_bldo1>; + vcc-ph-supply = <®_cldo3>; /* via VCC-IO */ + vcc-pi-supply = <®_cldo3>; + vcc-pj-supply = <®_cldo1>; + vcc-pk-supply = <®_cldo1>; +}; + +&r_i2c0 { + status = "okay"; + + axp717: pmic@35 { + compatible = "x-powers,axp717"; + reg = <0x35>; + interrupt-controller; + #interrupt-cells = <1>; + interrupts-extended = <&nmi_intc 0 IRQ_TYPE_LEVEL_LOW>; + + vin1-supply = <®_vcc5v>; + vin2-supply = <®_vcc5v>; + vin3-supply = <®_vcc5v>; + vin4-supply = <®_vcc5v>; + aldoin-supply = <®_vcc5v>; + bldoin-supply = <®_vcc5v>; + cldoin-supply = <®_vcc5v>; + + regulators { + /* Supplies the "little" cluster (1.4 GHz cores) */ + reg_dcdc1: dcdc1 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1160000>; + regulator-name = "vdd-cpul"; + }; + + reg_dcdc2: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <920000>; + regulator-max-microvolt = <920000>; + regulator-name = "vdd-gpu-sys"; + }; + + reg_dcdc3: dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1160000>; + regulator-max-microvolt = <1160000>; + regulator-name = "vcc-dram"; + }; + + reg_dcdc4: dcdc4 { + /* feeds 3.3V pin on GPIO header */ + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vdd-io"; + }; + + aldo1 { + /* not actually connected */ + regulator-name = "avdd-csi"; + }; + + reg_aldo2: aldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pe"; + }; + + reg_aldo3: aldo3 { + /* supplies the I2C pins for this PMIC */ + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pl-usb"; + }; + + reg_aldo4: aldo4 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pll-dxco-avcc"; + }; + + reg_bldo1: bldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pg-wifi"; + }; + + reg_bldo2: bldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pm-lpddr"; + }; + + bldo3 { + /* not actually connected */ + regulator-name = "afvcc-csi"; + }; + + bldo4 { + /* not actually connected */ + regulator-name = "dvdd-csi"; + }; + + reg_cldo1: cldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-cvp-pc-lvds-mcsi-pk-efuse-pcie-edp-1v8"; + }; + + reg_cldo2: cldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3-csi"; + }; + + reg_cldo3: cldo3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-io-mmc-nand-pd-pi-usb"; + }; + + reg_cldo4: cldo4 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3-phy1-lcd"; + }; + + reg_cpusldo: cpusldo { + /* supplies the management core */ + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdd-cpus-usb-0v9"; + }; + }; + }; + + axp323: pmic@36 { + compatible = "x-powers,axp323"; + reg = <0x36>; + #interrupt-cells = <1>; + interrupt-controller; + status = "okay"; + + vin1-supply = <®_vcc5v>; + vin2-supply = <®_vcc5v>; + vin3-supply = <®_vcc5v>; + + regulators { + reg_aldo1_323: aldo1 { + /* less capable and shares load with dldo1 */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; + }; + + reg_dldo1_323: dldo1 { + /* more capable and shares load with aldo1 */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi2"; + }; + + /* Supplies the "big" cluster (1.8 GHz cores) */ + reg_dcdc1_323: dcdc1 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1150000>; + regulator-name = "vdd-cpub"; + }; + + /* DCDC2 is polyphased with DCDC1 */ + + /* Some RISC-V management core related voltage */ + reg_dcdc3_323: dcdc3 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdd-dnr"; + }; + }; + }; +}; + +&r_pio { +/* + * Specifying the supply would create a circular dependency. + * + * vcc-pl-supply = <®_aldo3>; + */ + vcc-pm-supply = <®_bldo2>; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm4345c5"; + clocks = <&rtc CLK_OSC32K_FANOUT>; + clock-names = "lpo"; + vbat-supply = <®_aldo1_323>; + vddio-supply = <®_bldo1>; + device-wakeup-gpios = <&r_pio 1 3 GPIO_ACTIVE_HIGH>; /* PM3 */ + host-wakeup-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */ + shutdown-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */ + }; +}; + +&usb_otg { + /* + * The OTG controller is connected to one of the type-A ports. + * There is a regulator, controlled by a GPIO, to provide VBUS power + * to the port, and a VBUSDET GPIO, to detect externally provided + * power. But without ID or CC pins there is no real way to do a + * runtime role detection. + */ + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + usb0_vbus-supply = <®_otg_vbus>; + usb0_vbus_det-gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */ + usb1_vbus-supply = <®_usb_vbus>; + status = "okay"; +};
Quoted 10 lines · Chen-Yu Tsai
This is v3 of my OrangePi 4A series.
Changes since v2:
- Actually include cpusldo regulator name change and axp323 aldo1/dldo1 comments
- Fix indentation of comment inusb_otgblock
- Link to v2:
https://lore.kernel.org/all/[email protected]/[...]
Applied to sunxi/dt-for-6.17 in local tree, thanks!
[1/5] dt-bindings: arm: sunxi: Add Xunlong OrangePi 4A board
commit: bbe7cf4bab161a50ce631c9dd7724df333cdf12d
[2/5] arm64: dts: allwinner: a523: Move mmc nodes to correct position
commit: 6e2662c07a90e9f782158b7d6eda2766f65e9c36
[3/5] arm64: dts: allwinner: a523: Move rgmii0 pins to correct location
commit: 84c4a16e00f5aadbb1a3bdecc6bbfee35b7c45c8
[4/5] arm64: dts: allwinner: a523: Add UART1 pins
commit: 64f2f7bc4acb7928b39cac4a9a932e77b966f31c
[5/5] arm64: dts: allwinner: t527: Add OrangePi 4A board
commit: de713ccb99345be302adf507274d1b190dd2302eBest regards,
Signature · 1 line
Chen-Yu Tsai <[email protected]>