Allwinner A100/A133 Ethernet MAC (EMAC0) Support
Subsystems (4)
v2 cover Allwinner A100/A133 Ethernet MAC (EMAC0) Support
This series adds support for the Alwinner A100/A133 Ethernet MAC (EMAC0) and uses it in the Liontron H-A133L board.
Changes since v1:
- Reverted the emac0 to emac rename;
- Added collected tags.
Paul Kocialkowski (4):
Revert "pinctrl: sunxi: Fix a100 emac pin function name"
arm64: dts: allwinner: a100: Add pin definitions for RGMII/RMII
arm64: dts: allwinner: a100: Add EMAC support
arm64: dts: allwinner: a133-liontron-h-a133l: Add Ethernet support
.../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 35 +++++++++++++++++++ .../sun50i-a133-liontron-h-a133l.dts | 19 ++++++++++ drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 32 ++++++++--------- 3 files changed, 70 insertions(+), 16 deletions(-)
Signature · 1 line
2.49.0
PATCH v2 1/4 Revert "pinctrl: sunxi: Fix a100 emac pin function name"
While the A100/A133 chips only expose a single EMAC, the sun50iw10 die that they share actually has two such controllers.
One specific package, the T509 is reported to expose both ports.
Since we want to keep the pinctrl function names unique accross packages of the same die to share a single common base dtsi, keep the emac0 naming in order to allow the introduction of the emac1 function in the future.
Note that the original commit also breaks the ABI between the driver and the device-tree. It's however unlikely that anybody would have complained about that since the a100/a133 port is still very early and experimental.
--- drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 32 ++++++++++----------- 1 file changed, 16 insertions(+), 16 deletions(-)
drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c +16 -16
@@ -546,33 +546,33 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x0, "gpio_in"), SUNXI_FUNCTION(0x1, "gpio_out"), SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */ - SUNXI_FUNCTION(0x5, "emac"), /* RXD1 */ + SUNXI_FUNCTION(0x5, "emac0"), /* RXD1 */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 0)),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,1 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x2 ,"i2c0" ),/* SDA */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* RXD0 */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* RXD0 */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,1 )),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,2 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x2 ,"i2c1" ),/* SCK */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* RXCTL */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* RXCTL */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,2 )),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,3 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x2 ,"i2c1" ),/* SDA */ SUNXI_FUNCTION (0x3 ,"cir0" ),/* OUT */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* CLKIN */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* CLKIN */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,3 )),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,4 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x2 ,"uart3" ),/* TX */ SUNXI_FUNCTION (0x3 ,"spi1" ),/* CS */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* TXD1 */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* TXD1 */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,4 )), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 5), SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -580,14 +580,14 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x2, "uart3"), /* RX */ SUNXI_FUNCTION(0x3, "spi1"), /* CLK */ SUNXI_FUNCTION(0x4, "ledc"), - SUNXI_FUNCTION(0x5, "emac"), /* TXD0 */ + SUNXI_FUNCTION(0x5, "emac0"), /* TXD0 */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 5)),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,6 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x2 ,"uart3" ),/* RTS */ SUNXI_FUNCTION (0x3 ,"spi1" ),/* MOSI */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* TXCK */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* TXCK */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,6 )), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7), SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -595,7 +595,7 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x2, "uart3"), /* CTS */ SUNXI_FUNCTION(0x3, "spi1"), /* MISO */ SUNXI_FUNCTION(0x4, "spdif"), /* OUT */ - SUNXI_FUNCTION(0x5, "emac"), /* TXCTL */ + SUNXI_FUNCTION(0x5, "emac0"), /* TXCTL */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 7)), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8), SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -611,7 +611,7 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x2, "dmic"), /* DATA0 */ SUNXI_FUNCTION(0x3, "spi2"), /* CLK */ SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */ - SUNXI_FUNCTION(0x5, "emac"), /* MDC */ + SUNXI_FUNCTION(0x5, "emac0"), /* MDC */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 9)), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10), SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -619,7 +619,7 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x2, "dmic"), /* DATA1 */ SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */ SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */ - SUNXI_FUNCTION(0x5, "emac"), /* MDIO */ + SUNXI_FUNCTION(0x5, "emac0"), /* MDIO */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 10)), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 11), SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -642,33 +642,33 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x1, "gpio_out"), SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */ SUNXI_FUNCTION(0x4, "i2s3"), /* MCLK */ - SUNXI_FUNCTION(0x5, "emac"), /* EPHY */ + SUNXI_FUNCTION(0x5, "emac0"), /* EPHY */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 13)),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,14 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x4 ,"i2s3" ),/* BCLK */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* RXD3 */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* RXD3 */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,14 )),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,15 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x4 ,"i2s3" ),/* LRCK */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* RXD2 */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* RXD2 */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,15 )),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,16 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x3 ,"i2s3_dout0" ),/* DOUT0 */ SUNXI_FUNCTION (0x4 ,"i2s3_din1" ),/* DIN1 */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* RXCK */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* RXCK */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,16 )),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,17 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x3 ,"i2s3_dout1" ),/* DOUT1 */ SUNXI_FUNCTION (0x4 ,"i2s3_din0" ),/* DIN0 */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* TXD3 */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* TXD3 */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,17 )), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 18), SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -676,7 +676,7 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x2, "cir0"), /* OUT */ SUNXI_FUNCTION(0x3, "i2s3_dout2"), /* DOUT2 */ SUNXI_FUNCTION(0x4, "i2s3_din2"), /* DIN2 */ - SUNXI_FUNCTION(0x5, "emac"), /* TXD2 */ + SUNXI_FUNCTION(0x5, "emac0"), /* TXD2 */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 18)), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 19), SUNXI_FUNCTION(0x0, "gpio_in"),
Signature · 1 line
2.49.0
Re: [PATCH v2 1/4] Revert "pinctrl: sunxi: Fix a100 emac pin function name"
On Mon, 7 Jul 2025 18:51:52 +0200
Paul Kocialkowski <[email protected]> wrote:
Hi Paul,
Quoted 10 lines
While the A100/A133 chips only expose a single EMAC, the sun50iw10 die that they share actually has two such controllers.
One specific package, the T509 is reported to expose both ports.
Since we want to keep the pinctrl function names unique accross packages of the same die to share a single common base dtsi, keep the emac0 naming in order to allow the introduction of the emac1 function in the future.
Quoted 7 lines
Note that the original commit also breaks the ABI between the driver and the device-tree. It's however unlikely that anybody would have complained about that since the a100/a133 port is still very early and experimental.
Fixes d4775ba60b55 ("pinctrl: sunxi: Fix a100 emac pin function name")Signed-off-by Paul Kocialkowski <[email protected]>
many thanks for sending this, it looks good to me now. I just wonder if the original patch can be still backed out, I think it would be still time before the v6.17 PR?
Good to have an explicit revert anyway, to make this case clear.
Cheers,
Andre
Quoted 139 lines
--- drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 32 ++++++++++----------- 1 file changed, 16 insertions(+), 16 deletions(-)drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c +16
-16@@ -546,33 +546,33 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x0, "gpio_in"), SUNXI_FUNCTION(0x1, "gpio_out"), SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */ - SUNXI_FUNCTION(0x5, "emac"), /* RXD1 */ + SUNXI_FUNCTION(0x5, "emac0"), /* RXD1 */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 0)),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,1 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x2 ,"i2c0" ),/* SDA */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* RXD0 */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* RXD0 */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,1 )),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,2 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x2 ,"i2c1" ),/* SCK */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* RXCTL */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* RXCTL */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,2 )),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,3 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x2 ,"i2c1" ),/* SDA */ SUNXI_FUNCTION (0x3 ,"cir0" ),/* OUT */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* CLKIN */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* CLKIN */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,3 )),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,4 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x2 ,"uart3" ),/* TX */ SUNXI_FUNCTION (0x3 ,"spi1" ),/* CS */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* TXD1 */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* TXD1 */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,4 )), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 5), SUNXI_FUNCTION(0x0, "gpio_in"),@@ -580,14 +580,14 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x2, "uart3"), /* RX */ SUNXI_FUNCTION(0x3, "spi1"), /* CLK */ SUNXI_FUNCTION(0x4, "ledc"), - SUNXI_FUNCTION(0x5, "emac"), /* TXD0 */ + SUNXI_FUNCTION(0x5, "emac0"), /* TXD0 */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 5)),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,6 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x2 ,"uart3" ),/* RTS */ SUNXI_FUNCTION (0x3 ,"spi1" ),/* MOSI */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* TXCK */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* TXCK */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,6 )), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7), SUNXI_FUNCTION(0x0, "gpio_in"),@@ -595,7 +595,7 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x2, "uart3"), /* CTS */ SUNXI_FUNCTION(0x3, "spi1"), /* MISO */ SUNXI_FUNCTION(0x4, "spdif"), /* OUT */ - SUNXI_FUNCTION(0x5, "emac"), /* TXCTL */ + SUNXI_FUNCTION(0x5, "emac0"), /* TXCTL */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 7)), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8), SUNXI_FUNCTION(0x0, "gpio_in"),@@ -611,7 +611,7 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x2, "dmic"), /* DATA0 */ SUNXI_FUNCTION(0x3, "spi2"), /* CLK */ SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */ - SUNXI_FUNCTION(0x5, "emac"), /* MDC */ + SUNXI_FUNCTION(0x5, "emac0"), /* MDC */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 9)), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10), SUNXI_FUNCTION(0x0, "gpio_in"),@@ -619,7 +619,7 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x2, "dmic"), /* DATA1 */ SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */ SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */ - SUNXI_FUNCTION(0x5, "emac"), /* MDIO */ + SUNXI_FUNCTION(0x5, "emac0"), /* MDIO */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 10)), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 11), SUNXI_FUNCTION(0x0, "gpio_in"),@@ -642,33 +642,33 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x1, "gpio_out"), SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */ SUNXI_FUNCTION(0x4, "i2s3"), /* MCLK */ - SUNXI_FUNCTION(0x5, "emac"), /* EPHY */ + SUNXI_FUNCTION(0x5, "emac0"), /* EPHY */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 13)),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,14 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x4 ,"i2s3" ),/* BCLK */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* RXD3 */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* RXD3 */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,14 )),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,15 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x4 ,"i2s3" ),/* LRCK */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* RXD2 */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* RXD2 */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,15 )),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,16 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x3 ,"i2s3_dout0" ),/* DOUT0 */ SUNXI_FUNCTION (0x4 ,"i2s3_din1" ),/* DIN1 */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* RXCK */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* RXCK */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,16 )),SUNXI_PIN (SUNXI_PINCTRL_PIN (H ,17 ),SUNXI_FUNCTION (0x0 ,"gpio_in" ),SUNXI_FUNCTION (0x1 ,"gpio_out" ),SUNXI_FUNCTION (0x3 ,"i2s3_dout1" ),/* DOUT1 */ SUNXI_FUNCTION (0x4 ,"i2s3_din0" ),/* DIN0 */ -SUNXI_FUNCTION (0x5 ,"emac" ),/* TXD3 */ +SUNXI_FUNCTION (0x5 ,"emac0" ),/* TXD3 */ SUNXI_FUNCTION_IRQ_BANK (0x6 ,6 ,17 )), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 18), SUNXI_FUNCTION(0x0, "gpio_in"),@@ -676,7 +676,7 @@ static const struct sunxi_desc_pin a100_pins[] = { SUNXI_FUNCTION(0x2, "cir0"), /* OUT */ SUNXI_FUNCTION(0x3, "i2s3_dout2"), /* DOUT2 */ SUNXI_FUNCTION(0x4, "i2s3_din2"), /* DIN2 */ - SUNXI_FUNCTION(0x5, "emac"), /* TXD2 */ + SUNXI_FUNCTION(0x5, "emac0"), /* TXD2 */ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 18)), SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 19), SUNXI_FUNCTION(0x0, "gpio_in"),
Re: [PATCH v2 1/4] Revert "pinctrl: sunxi: Fix a100 emac pin function name"
Quoted 6 lines · Andre Przywara
Quoted 2 lines
Fixes d4775ba60b55 ("pinctrl: sunxi: Fix a100 emac pin function name")Signed-off-by Paul Kocialkowski <[email protected]>many thanks for sending this, it looks good to me now. I just wonder if the original patch can be still backed out, I think it would be still time before the v6.17 PR?
Yeah I just dropped the patch :)
Yours,
Linus Walleij
PATCH v2 2/4 arm64: dts: allwinner: a100: Add pin definitions for RGMII/RMII
In reply to Paul KocialkowskiThe Allwinner A100/A133 supports both RGMII and RMII for its Ethernet MAC (EMAC) controller. Add corresponding pin definitions.
Note that the sun50iw10 die actually includes two ethernet controllers, the second of which is rarely exposed to pins. Call the first controller "emac0" to distinguish it from the second that may be added later.
--- arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +15 -0
@@ -236,6 +236,21 @@ mmc2_pins: mmc2-pins { bias-pull-up; }; + rgmii0_pins: rgmii0-pins { + pins = "PH0", "PH1", "PH2", "PH3", "PH4", + "PH5", "PH6", "PH7", "PH9", "PH10", + "PH14", "PH15", "PH16", "PH17", "PH18"; + function = "emac0"; + drive-strength = <40>; + }; + + rmii0_pins: rmii0-pins { + pins = "PH0", "PH1", "PH2", "PH3", "PH4", + "PH5", "PH6", "PH7", "PH9", "PH10"; + function = "emac0"; + drive-strength = <40>; + }; + uart0_pb_pins: uart0-pb-pins { pins = "PB9", "PB10"; function = "uart0";
Signature · 1 line
2.49.0
PATCH v2 3/4 arm64: dts: allwinner: a100: Add EMAC support
In reply to Paul KocialkowskiThe Allwinner A100/A133 Ethernet MAC (EMAC) is compatible with the A64 one and needs access to the syscon register for control of the top-level integration of the unit.
Note that there are two such controllers on the sun50iw10 die, which are the same unit with a different top-level syscon register offset.
--- .../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 20 +++++++++++++++++++ 1 file changed, 20 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +20 -0
@@ -420,6 +420,26 @@ i2c3: i2c@5002c00 { #size-cells = <0>; }; + emac0: ethernet@5020000 { + compatible = "allwinner,sun50i-a100-emac", + "allwinner,sun50i-a64-emac"; + reg = <0x5020000 0x10000>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + syscon = <&syscon>; + status = "disabled"; + + mdio0: mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + ths: thermal-sensor@5070400 { compatible = "allwinner,sun50i-a100-ths"; reg = <0x05070400 0x100>;
Signature · 1 line
2.49.0
PATCH v2 4/4 arm64: dts: allwinner: a133-liontron-h-a133l: Add Ethernet support
In reply to Paul KocialkowskiThe Liontron H-A133L board features an Ethernet controller with a JLSemi JL1101 PHY. Its reset pin is tied to the PH12 GPIO.
Note that the reset pin must be handled as a bus-wide reset GPIO in order to let the MDIO core properly reset it before trying to read its identification registers. There's no other device on the MDIO bus.
The datasheet of the PHY mentions that the reset signal must be held for 1 ms to take effect. Make it 2 ms (and the same for post-delay) to be on the safe side without wasting too much time during boot.
--- .../sun50i-a133-liontron-h-a133l.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a133-liontron-h-a133l.dts +19 -0
@@ -65,6 +65,25 @@ &ehci1 { status = "okay"; }; +&emac0 { + pinctrl-names = "default"; + pinctrl-0 = <&rmii0_pins>; + phy-handle = <&rmii_phy>; + phy-mode = "rmii"; + status = "okay"; +}; + +&mdio0 { + reset-gpios = <&pio 7 12 GPIO_ACTIVE_LOW>; /* PH12 */ + reset-delay-us = <2000>; + reset-post-delay-us = <2000>; + + rmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { vmmc-supply = <®_dcdc1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
Signature · 1 line
2.49.0
Re: [PATCH v2 4/4] arm64: dts: allwinner: a133-liontron-h-a133l: Add Ethernet support
On Mon, 7 Jul 2025 18:51:55 +0200
Paul Kocialkowski <[email protected]> wrote:
Hi Paul,
Quoted 6 lines
The Liontron H-A133L board features an Ethernet controller with a JLSemi JL1101 PHY. Its reset pin is tied to the PH12 GPIO.
Note that the reset pin must be handled as a bus-wide reset GPIO in order to let the MDIO core properly reset it before trying to read its identification registers. There's no other device on the MDIO bus.
putting the PHY reset GPIO into the MDIO node is a clever solution, I was struggling with putting it either in the MAC or PHY node, though conceptually it would still belong in the latter, I think. But this might be a more generic problem: for most other devices we activate reset and clock gates *before* trying to access them, though this might be historically different for Ethernet PHYs.
Quoted 5 lines
The datasheet of the PHY mentions that the reset signal must be held for 1 ms to take effect. Make it 2 ms (and the same for post-delay) to be on the safe side without wasting too much time during boot.
Signed-off-by Paul Kocialkowski <[email protected]>
Despite the above, this looks fine, and works for me:
Cheers,
Andre
Quoted 34 lines
--- .../sun50i-a133-liontron-h-a133l.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-a133-liontron-h-a133l.dts +19
-0@@ -65,6 +65,25 @@ &ehci1 { status = "okay"; }; +&emac0 { + pinctrl-names = "default"; + pinctrl-0 = <&rmii0_pins>; + phy-handle = <&rmii_phy>; + phy-mode = "rmii"; + status = "okay"; +}; + +&mdio0 { + reset-gpios = <&pio 7 12 GPIO_ACTIVE_LOW>; /* PH12 */ + reset-delay-us = <2000>; + reset-post-delay-us = <2000>; + + rmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { vmmc-supply = <®_dcdc1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
Re: [PATCH v2 4/4] arm64: dts: allwinner: a133-liontron-h-a133l: Add Ethernet support
On Tue, 8 Jul 2025 00:34:25 +0100
Andre Przywara <[email protected]> wrote:
Hi Paul,
forgot to mention: can you please add an ethernet0 alias, to make U-Boot generate a MAC address, from the SID?
Cheers,
Andre
Quoted 68 lines
On Mon, 7 Jul 2025 18:51:55 +0200
Paul Kocialkowski <[email protected]> wrote:Hi Paul,
Quoted 6 lines
The Liontron H-A133L board features an Ethernet controller with a JLSemi JL1101 PHY. Its reset pin is tied to the PH12 GPIO.
Note that the reset pin must be handled as a bus-wide reset GPIO in order to let the MDIO core properly reset it before trying to read its identification registers. There's no other device on the MDIO bus.
putting the PHY reset GPIO into the MDIO node is a clever solution, I was struggling with putting it either in the MAC or PHY node, though conceptually it would still belong in the latter, I think. But this might be a more generic problem: for most other devices we activate reset and clock gates *before* trying to access them, though this might be historically different for Ethernet PHYs.
Quoted 5 lines
The datasheet of the PHY mentions that the reset signal must be held for 1 ms to take effect. Make it 2 ms (and the same for post-delay) to be on the safe side without wasting too much time during boot.
Signed-off-by Paul Kocialkowski <[email protected]>Despite the above, this looks fine, and works for me:
Reviewed-by Andre Przywara <[email protected]>Tested-by Andre Przywara <[email protected]>Cheers,
AndreQuoted 34 lines
--- .../sun50i-a133-liontron-h-a133l.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-a133-liontron-h-a133l.dts +19
-0@@ -65,6 +65,25 @@ &ehci1 { status = "okay"; }; +&emac0 { + pinctrl-names = "default"; + pinctrl-0 = <&rmii0_pins>; + phy-handle = <&rmii_phy>; + phy-mode = "rmii"; + status = "okay"; +}; + +&mdio0 { + reset-gpios = <&pio 7 12 GPIO_ACTIVE_LOW>; /* PH12 */ + reset-delay-us = <2000>; + reset-post-delay-us = <2000>; + + rmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { vmmc-supply = <®_dcdc1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
Re: [PATCH v2 4/4] arm64: dts: allwinner: a133-liontron-h-a133l: Add Ethernet support
Hi Andre,
Quoted 7 lines · Andre Przywara
On Tue, 8 Jul 2025 00:34:25 +0100
Andre Przywara <[email protected]> wrote:Hi Paul,
forgot to mention: can you please add an ethernet0 alias, to make U-Boot generate a MAC address, from the SID?
Ah yes, sorry I forgot to do that. Will respin the series then.
Cheers,
Paul
Quoted 72 lines
Cheers,
AndreQuoted 68 lines
On Mon, 7 Jul 2025 18:51:55 +0200
Paul Kocialkowski <[email protected]> wrote:Hi Paul,
Quoted 6 lines
The Liontron H-A133L board features an Ethernet controller with a JLSemi JL1101 PHY. Its reset pin is tied to the PH12 GPIO.
Note that the reset pin must be handled as a bus-wide reset GPIO in order to let the MDIO core properly reset it before trying to read its identification registers. There's no other device on the MDIO bus.
putting the PHY reset GPIO into the MDIO node is a clever solution, I was struggling with putting it either in the MAC or PHY node, though conceptually it would still belong in the latter, I think. But this might be a more generic problem: for most other devices we activate reset and clock gates *before* trying to access them, though this might be historically different for Ethernet PHYs.
Quoted 5 lines
The datasheet of the PHY mentions that the reset signal must be held for 1 ms to take effect. Make it 2 ms (and the same for post-delay) to be on the safe side without wasting too much time during boot.
Signed-off-by Paul Kocialkowski <[email protected]>Despite the above, this looks fine, and works for me:
Reviewed-by Andre Przywara <[email protected]>Tested-by Andre Przywara <[email protected]>Cheers,
AndreQuoted 34 lines
--- .../sun50i-a133-liontron-h-a133l.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-a133-liontron-h-a133l.dts +19
-0@@ -65,6 +65,25 @@ &ehci1 { status = "okay"; }; +&emac0 { + pinctrl-names = "default"; + pinctrl-0 = <&rmii0_pins>; + phy-handle = <&rmii_phy>; + phy-mode = "rmii"; + status = "okay"; +}; + +&mdio0 { + reset-gpios = <&pio 7 12 GPIO_ACTIVE_LOW>; /* PH12 */ + reset-delay-us = <2000>; + reset-post-delay-us = <2000>; + + rmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { vmmc-supply = <®_dcdc1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
Signature · 6 lines
Paul Kocialkowski, Independent contractor - sys-base - https://www.sys-base.io/ Free software developer - https://www.paulk.fr/ Expert in multimedia, graphics and embedded hardware support with Linux.
Re: [PATCH v2 4/4] arm64: dts: allwinner: a133-liontron-h-a133l: Add Ethernet support
In reply to Andre PrzywaraQuoted 13 lines · Andre Przywara
On Mon, 7 Jul 2025 18:51:55 +0200
Paul Kocialkowski <[email protected]> wrote:Hi Paul,
Quoted 6 lines
The Liontron H-A133L board features an Ethernet controller with a JLSemi JL1101 PHY. Its reset pin is tied to the PH12 GPIO.
Note that the reset pin must be handled as a bus-wide reset GPIO in order to let the MDIO core properly reset it before trying to read its identification registers. There's no other device on the MDIO bus.
Quoted 6 lines
putting the PHY reset GPIO into the MDIO node is a clever solution, I was struggling with putting it either in the MAC or PHY node, though conceptually it would still belong in the latter, I think. But this might be a more generic problem: for most other devices we activate reset and clock gates *before* trying to access them, though this might be historically different for Ethernet PHYs.
The phylib core has code to deal with reset GPIOs listed under the PHY node. It might be worth checking why that doesn't work.
OOTH, there's no code to deal with regulator supplies for PHYs.
ChenYu
Quoted 50 lines
Quoted 5 lines
The datasheet of the PHY mentions that the reset signal must be held for 1 ms to take effect. Make it 2 ms (and the same for post-delay) to be on the safe side without wasting too much time during boot.
Signed-off-by Paul Kocialkowski <[email protected]>Despite the above, this looks fine, and works for me:
Reviewed-by Andre Przywara <[email protected]>Tested-by Andre Przywara <[email protected]>Cheers,
AndreQuoted 34 lines
--- .../sun50i-a133-liontron-h-a133l.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-a133-liontron-h-a133l.dts +19
-0@@ -65,6 +65,25 @@ &ehci1 { status = "okay"; }; +&emac0 { + pinctrl-names = "default"; + pinctrl-0 = <&rmii0_pins>; + phy-handle = <&rmii_phy>; + phy-mode = "rmii"; + status = "okay"; +}; + +&mdio0 { + reset-gpios = <&pio 7 12 GPIO_ACTIVE_LOW>; /* PH12 */ + reset-delay-us = <2000>; + reset-post-delay-us = <2000>; + + rmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { vmmc-supply = <®_dcdc1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
Re: [PATCH v2 4/4] arm64: dts: allwinner: a133-liontron-h-a133l: Add Ethernet support
Hi,
Quoted 21 lines · Chen-Yu Tsai
Quoted 13 lines · Andre Przywara
On Mon, 7 Jul 2025 18:51:55 +0200
Paul Kocialkowski <[email protected]> wrote:Hi Paul,
Quoted 6 lines
The Liontron H-A133L board features an Ethernet controller with a JLSemi JL1101 PHY. Its reset pin is tied to the PH12 GPIO.
Note that the reset pin must be handled as a bus-wide reset GPIO in order to let the MDIO core properly reset it before trying to read its identification registers. There's no other device on the MDIO bus.
Quoted 6 lines
putting the PHY reset GPIO into the MDIO node is a clever solution, I was struggling with putting it either in the MAC or PHY node, though conceptually it would still belong in the latter, I think. But this might be a more generic problem: for most other devices we activate reset and clock gates *before* trying to access them, though this might be historically different for Ethernet PHYs.
Quoted 2 lines
The phylib core has code to deal with reset GPIOs listed under the PHY node. It might be worth checking why that doesn't work.
While this code does exist, it's too early to be called when the mdio bus is trying to probe the phy. I was also surprised the existing reset gpio support in the phylib core didn't take effect (that's how I tried to implement it first) only to find that the code was never called. It's only called once the phy was probed and registered.
Cheers,
Paul
Quoted 54 lines
OOTH, there's no code to deal with regulator supplies for PHYs.
ChenYu
Quoted 50 lines
Quoted 5 lines
The datasheet of the PHY mentions that the reset signal must be held for 1 ms to take effect. Make it 2 ms (and the same for post-delay) to be on the safe side without wasting too much time during boot.
Signed-off-by Paul Kocialkowski <[email protected]>Despite the above, this looks fine, and works for me:
Reviewed-by Andre Przywara <[email protected]>Tested-by Andre Przywara <[email protected]>Cheers,
AndreQuoted 34 lines
--- .../sun50i-a133-liontron-h-a133l.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-a133-liontron-h-a133l.dts +19
-0@@ -65,6 +65,25 @@ &ehci1 { status = "okay"; }; +&emac0 { + pinctrl-names = "default"; + pinctrl-0 = <&rmii0_pins>; + phy-handle = <&rmii_phy>; + phy-mode = "rmii"; + status = "okay"; +}; + +&mdio0 { + reset-gpios = <&pio 7 12 GPIO_ACTIVE_LOW>; /* PH12 */ + reset-delay-us = <2000>; + reset-post-delay-us = <2000>; + + rmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { vmmc-supply = <®_dcdc1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
Signature · 6 lines
Paul Kocialkowski, Independent contractor - sys-base - https://www.sys-base.io/ Free software developer - https://www.paulk.fr/ Expert in multimedia, graphics and embedded hardware support with Linux.
Re: [PATCH v2 4/4] arm64: dts: allwinner: a133-liontron-h-a133l: Add Ethernet support
Quoted 25 lines · Paul Kocialkowski
Hi,
Quoted 21 lines · Chen-Yu Tsai
Quoted 19 lines · Andre Przywara
On Mon, 7 Jul 2025 18:51:55 +0200
Paul Kocialkowski <[email protected]> wrote:Hi Paul,
Quoted 6 lines
The Liontron H-A133L board features an Ethernet controller with a JLSemi JL1101 PHY. Its reset pin is tied to the PH12 GPIO.
Note that the reset pin must be handled as a bus-wide reset GPIO in order to let the MDIO core properly reset it before trying to read its identification registers. There's no other device on the MDIO bus.
putting the PHY reset GPIO into the MDIO node is a clever solution, I was struggling with putting it either in the MAC or PHY node, though conceptually it would still belong in the latter, I think. But this might be a more generic problem: for most other devices we activate reset and clock gates *before* trying to access them, though this might be historically different for Ethernet PHYs.
Quoted 8 lines
Quoted 2 lines
The phylib core has code to deal with reset GPIOs listed under the PHY node. It might be worth checking why that doesn't work.
While this code does exist, it's too early to be called when the mdio bus is trying to probe the phy. I was also surprised the existing reset gpio support in the phylib core didn't take effect (that's how I tried to implement it first) only to find that the code was never called. It's only called once the phy was probed and registered.
OK, that's definitely weird. The code looked like it just walked the DT and registered PHY devices, upon which the GPIO lines would be found and toggled.
ChenYu
Quoted 66 lines
Cheers,
Paul
Quoted 54 lines
OOTH, there's no code to deal with regulator supplies for PHYs.
ChenYu
Quoted 50 lines
Quoted 5 lines
The datasheet of the PHY mentions that the reset signal must be held for 1 ms to take effect. Make it 2 ms (and the same for post-delay) to be on the safe side without wasting too much time during boot.
Signed-off-by Paul Kocialkowski <[email protected]>Despite the above, this looks fine, and works for me:
Reviewed-by Andre Przywara <[email protected]>Tested-by Andre Przywara <[email protected]>Cheers,
AndreQuoted 34 lines
--- .../sun50i-a133-liontron-h-a133l.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-a133-liontron-h-a133l.dts +19
-0@@ -65,6 +65,25 @@ &ehci1 { status = "okay"; }; +&emac0 { + pinctrl-names = "default"; + pinctrl-0 = <&rmii0_pins>; + phy-handle = <&rmii_phy>; + phy-mode = "rmii"; + status = "okay"; +}; + +&mdio0 { + reset-gpios = <&pio 7 12 GPIO_ACTIVE_LOW>; /* PH12 */ + reset-delay-us = <2000>; + reset-post-delay-us = <2000>; + + rmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { vmmc-supply = <®_dcdc1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */--
Paul Kocialkowski,Independent contractor - sys-base - https://www.sys-base.io/
Free software developer - https://www.paulk.fr/Expert in multimedia, graphics and embedded hardware support with Linux.
Re: [PATCH v2 4/4] arm64: dts: allwinner: a133-liontron-h-a133l: Add Ethernet support
In reply to Andre PrzywaraHi Andre,
Quoted 12 lines · Andre Przywara
On Mon, 7 Jul 2025 18:51:55 +0200
Paul Kocialkowski <[email protected]> wrote:Hi Paul,
Quoted 6 lines
The Liontron H-A133L board features an Ethernet controller with a JLSemi JL1101 PHY. Its reset pin is tied to the PH12 GPIO.
Note that the reset pin must be handled as a bus-wide reset GPIO in order to let the MDIO core properly reset it before trying to read its identification registers. There's no other device on the MDIO bus.
Quoted 6 lines
putting the PHY reset GPIO into the MDIO node is a clever solution, I was struggling with putting it either in the MAC or PHY node, though conceptually it would still belong in the latter, I think. But this might be a more generic problem: for most other devices we activate reset and clock gates *before* trying to access them, though this might be historically different for Ethernet PHYs.
Yes this feels a bit unusual. Unfortunately the mdio bus performs probing on the PHYs before registering them as devices, which gives us no hope of running driver-specific code to power the PHY up.
So the only device we can hold on to is the mdio bus. I think there was an initial design assumption that 1 mdio bus == 1 PHY device
Quoted 10 lines
Quoted 5 lines
The datasheet of the PHY mentions that the reset signal must be held for 1 ms to take effect. Make it 2 ms (and the same for post-delay) to be on the safe side without wasting too much time during boot.
Signed-off-by Paul Kocialkowski <[email protected]>Despite the above, this looks fine, and works for me:
Reviewed-by Andre Przywara <[email protected]>Tested-by Andre Przywara <[email protected]>
Thanks for the review and test!
Paul
Quoted 38 lines
Cheers,
AndreQuoted 34 lines
--- .../sun50i-a133-liontron-h-a133l.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-a133-liontron-h-a133l.dts +19
-0@@ -65,6 +65,25 @@ &ehci1 { status = "okay"; }; +&emac0 { + pinctrl-names = "default"; + pinctrl-0 = <&rmii0_pins>; + phy-handle = <&rmii_phy>; + phy-mode = "rmii"; + status = "okay"; +}; + +&mdio0 { + reset-gpios = <&pio 7 12 GPIO_ACTIVE_LOW>; /* PH12 */ + reset-delay-us = <2000>; + reset-post-delay-us = <2000>; + + rmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { vmmc-supply = <®_dcdc1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
Signature · 6 lines
Paul Kocialkowski, Independent contractor - sys-base - https://www.sys-base.io/ Free software developer - https://www.paulk.fr/ Expert in multimedia, graphics and embedded hardware support with Linux.
Re: (subset) [PATCH v2 0/4] Allwinner A100/A133 Ethernet MAC (EMAC0) Support
In reply to Paul KocialkowskiQuoted 8 lines · Paul Kocialkowski
This series adds support for the Alwinner A100/A133 Ethernet MAC (EMAC0) and uses it in the Liontron H-A133L board.
Changes since v1:
- Reverted the emac0 to emac rename;
- Added collected tags.[...]
Applied to sunxi/dt-for-6.17 in local tree, thanks!
[2/4] arm64: dts: allwinner: a100: Add pin definitions for RGMII/RMII
commit: 28e4499a9ad68129d41db10b7481c61738fdb3d1
[3/4] arm64: dts: allwinner: a100: Add EMAC support
commit: 4e3be5629f1f6de30d3fbcdc357e7da948ccf698
[4/4] arm64: dts: allwinner: a133-liontron-h-a133l: Add Ethernet support
commit: 8f128f357dfe5907a6f3432ffb1f444e93f1fbf2Best regards,
Signature · 1 line
Chen-Yu Tsai <[email protected]>