watchdog: sbsa: Adjust keepalive timeout to avoid MediaTek WS0 race condition
PATCH 1/1 watchdog: sbsa: Adjust keepalive timeout to avoid MediaTek WS0 race condition
The MediaTek implementation of the sbsa_gwdt watchdog has a race condition where a write to SBSA_GWDT_WRR is ignored if it occurs while the hardware is processing a timeout refresh that asserts WS0.
Detect this based on the hardware implementer and adjust wdd->timeout to avoid the race.
--- drivers/watchdog/sbsa_gwdt.c | 52 +++++++++++++++++++++++++++++++++--- 1 file changed, 49 insertions(+), 3 deletions(-)
drivers/watchdog/sbsa_gwdt.c +49 -3
@@ -75,11 +75,17 @@#define SBSA_GWDT_VERSION_MASK 0xF#define SBSA_GWDT_VERSION_SHIFT 16 +#define SBSA_GWDT_IMPL_MASK 0x7FF +#define SBSA_GWDT_IMPL_SHIFT 0 +#define SBSA_GWDT_IMPL_MEDIATEK 0x426 +/** * struct sbsa_gwdt - Internal representation of the SBSA GWDT * @wdd: kernel watchdog_device structure * @clk: store the System Counter clock frequency, in Hz. * @version: store the architecture version +* @need_ws0_race_workaround: +* indicate whether to adjust wdd->timeout to avoid a race with WS0 * @refresh_base: Virtual address of the watchdog refresh frame * @control_base: Virtual address of the watchdog control frame */
@@ -87,6 +93,7 @@ struct sbsa_gwdt {struct watchdog_device wdd;u32 clk;int version; +bool need_ws0_race_workaround;void __iomem *refresh_base;void __iomem *control_base; };
@@ -161,6 +168,31 @@ static int sbsa_gwdt_set_timeout(struct watchdog_device *wdd,*/ sbsa_gwdt_reg_write (((u64 )gwdt->clk /2 ) * timeout, gwdt); +/* +* Some watchdog hardware has a race condition where it will ignore +* sbsa_gwdt_keepalive() if it is called at the exact moment that a +* timeout occurs and WS0 is being asserted. Unfortunately, the default +* behavior of the watchdog core is very likely to trigger this race +* when action=0 because it programs WOR to be half of the desired +* timeout, and watchdog_next_keepalive() chooses the exact same time to +* send keepalive pings. +* +* This triggers a race where sbsa_gwdt_keepalive() can be called right +* as WS0 is being asserted, and affected hardware will ignore that +* write and continue to assert WS0. After another (timeout / 2) +* seconds, the same race happens again. If the driver wins then the +* explicit refresh will reset WS0 to false but if the hardware wins, +* then WS1 is asserted and the system resets. +* +* Avoid the problem by scheduling keepalive heartbeats one second +* earlier than the WOR timeout. +* +* This workaround might not be needed in a future revision of the +* hardware. +*/ +if (gwdt->need_ws0_race_workaround) + wdd->timeout -=2 ; +return 0 ; }
@@ -202,12 +234,15 @@ static int sbsa_gwdt_keepalive(struct watchdog_device *wdd)static void sbsa_gwdt_get_version (struct watchdog_device *wdd) {struct sbsa_gwdt *gwdt =watchdog_get_drvdata (wdd); -int ver; +int iidr, ver, impl; - ver =readl (gwdt->control_base +SBSA_GWDT_W_IIDR ); - ver = (ver >>SBSA_GWDT_VERSION_SHIFT ) &SBSA_GWDT_VERSION_MASK ; + iidr =readl (gwdt->control_base +SBSA_GWDT_W_IIDR ); + ver = (iidr >>SBSA_GWDT_VERSION_SHIFT ) &SBSA_GWDT_VERSION_MASK ; + impl = (iidr >>SBSA_GWDT_IMPL_SHIFT ) &SBSA_GWDT_IMPL_MASK ; gwdt->version = ver; + gwdt->need_ws0_race_workaround = + !action && (impl ==SBSA_GWDT_IMPL_MEDIATEK ); }static int sbsa_gwdt_start (struct watchdog_device *wdd)
@@ -299,6 +334,15 @@ static int sbsa_gwdt_probe(struct platform_device *pdev)else wdd->max_hw_heartbeat_ms =GENMASK_ULL (47 ,0 ) / gwdt->clk *1000 ; +if (gwdt->need_ws0_race_workaround) { +/* +* A timeout of 3 seconds means that WOR will be set to 1.5 +* seconds and the heartbeat will be scheduled every 0.5 +* seconds. +*/ + wdd->min_timeout =3 ; + } + status =readl (cf_base +SBSA_GWDT_WCS );if (status &SBSA_GWDT_WCS_WS1 ) {dev_warn (dev,"System reset by WDT.\n" );
@@ -348,6 +392,8 @@ static int sbsa_gwdt_probe(struct platform_device *pdev)if (ret)return ret; +if (gwdt->need_ws0_race_workaround) +dev_warn (dev,"Adjusting timeout to avoid watchdog WS0 race condition.\n" );dev_info (dev,"Initialized with %ds timeout @ %u Hz, action=%d.%s\n" , wdd->timeout, gwdt->clk, action, status &SBSA_GWDT_WCS_EN ?" [enabled]" :"" );
Signature · 1 line
2.50.0
Guenter Roeck
maintainerQuoted 62 lines · Aaron Plattner
The MediaTek implementation of the
sbsa_gwdtwatchdog has a race condition where a write toSBSA_GWDT_WRRis ignored if it occurs while the hardware is processing a timeout refresh that asserts WS0.Detect this based on the hardware implementer and adjust
wdd->timeoutto avoid the race.Signed-off-by Aaron Plattner <[email protected]>Acked-by Timur Tabi <[email protected]>--- drivers/watchdog/sbsa_gwdt.c | 52 +++++++++++++++++++++++++++++++++--- 1 file changed, 49 insertions(+), 3 deletions(-)drivers/watchdog/sbsa_gwdt.c +22
-0@@ -75,11 +75,17 @@#define SBSA_GWDT_VERSION_MASK 0xF#define SBSA_GWDT_VERSION_SHIFT 16 +#define SBSA_GWDT_IMPL_MASK 0x7FF +#define SBSA_GWDT_IMPL_SHIFT 0 +#define SBSA_GWDT_IMPL_MEDIATEK 0x426 +/** * struct sbsa_gwdt - Internal representation of the SBSA GWDT * @wdd: kernel watchdog_device structure * @clk: store the System Counter clock frequency, in Hz. * @version: store the architecture version +* @need_ws0_race_workaround: +* indicate whether to adjust wdd->timeout to avoid a race with WS0 * @refresh_base: Virtual address of the watchdog refresh frame * @control_base: Virtual address of the watchdog control frame */ @@ -87,6 +93,7 @@ struct sbsa_gwdt {struct watchdog_device wdd;u32 clk;int version; +bool need_ws0_race_workaround;void __iomem *refresh_base;void __iomem *control_base; };@@ -161,6 +168,31 @@ static int sbsa_gwdt_set_timeout(struct watchdog_device *wdd,*/ sbsa_gwdt_reg_write (((u64 )gwdt->clk /2 ) * timeout, gwdt); +/* +* Some watchdog hardware has a race condition where it will ignore +* sbsa_gwdt_keepalive() if it is called at the exact moment that a +* timeout occurs and WS0 is being asserted. Unfortunately, the default +* behavior of the watchdog core is very likely to trigger this race +* when action=0 because it programs WOR to be half of the desired +* timeout, and watchdog_next_keepalive() chooses the exact same time to +* send keepalive pings. +* +* This triggers a race where sbsa_gwdt_keepalive() can be called right +* as WS0 is being asserted, and affected hardware will ignore that +* write and continue to assert WS0. After another (timeout / 2) +* seconds, the same race happens again. If the driver wins then the +* explicit refresh will reset WS0 to false but if the hardware wins, +* then WS1 is asserted and the system resets.
drivers/watchdog/sbsa_gwdt.c static int sbsa_gwdt_set_timeout(struct watchdog_device *wdd, · line 195
Quoted 10 lines
drivers/watchdog/sbsa_gwdt.c +10
-0+* +* Avoid the problem by scheduling keepalive heartbeats one second +* earlier than the WOR timeout. +* +* This workaround might not be needed in a future revision of the +* hardware. +*/ +if (gwdt->need_ws0_race_workaround) + wdd->timeout -=2 ; +
It seems to me that this is still racy. If the ping is ignored, I would assume that this is reflected in the watchdog registers. How about reading the status if the workaround is needed and issuing another keepalive if it was ignored ? Or just always issue a second write to SBSA_GWDT_WRR in that case, maybe after some short delay ?
Guenter
Quoted 75 lines · Guenter Roeck
Quoted 74 lines · Aaron Plattner
The MediaTek implementation of the
sbsa_gwdtwatchdog has a race condition where a write toSBSA_GWDT_WRRis ignored if it occurs while the hardware is processing a timeout refresh that asserts WS0.Detect this based on the hardware implementer and adjust
wdd->timeoutto avoid the race.Signed-off-by Aaron Plattner <[email protected]>Acked-by Timur Tabi <[email protected]>---
drivers/watchdog/sbsa_gwdt.c| 52 +++++++++++++++++++++++++++++++++---1 file changed, 49 insertions(+), 3 deletions(-)drivers/watchdog/sbsa_gwdt.c +6
-0@@ -75,11 +75,17 @@ #define SBSA_GWDT_VERSION_MASK 0xF #define SBSA_GWDT_VERSION_SHIFT 16 +#define SBSA_GWDT_IMPL_MASK 0x7FF +#define SBSA_GWDT_IMPL_SHIFT 0 +#define SBSA_GWDT_IMPL_MEDIATEK 0x426 + /*** struct sbsa_gwdt - Internal representation of the SBSA GWDT * @wdd: kernel watchdog_device structure * @clk: store the System Counter clock frequency, in Hz. * @version: store the architecture version +* @need_ws0_race_workaround: +* indicate whether to adjust wdd->timeout to avoid a race with WS0
* @refresh_base: Virtual address of the watchdog refresh frame
* @control_base: Virtual address of the watchdog control frame */drivers/watchdog/sbsa_gwdt.c +5
-0@@ -87,6 +93,7 @@ struct sbsa_gwdt { struct watchdog_device wdd; u32 clk; int version; + bool need_ws0_race_workaround; void __iomem *refresh_base; void __iomem *control_base; };@@ -161,6 +168,31 @@ static int sbsa_gwdt_set_timeout(structwatchdog_device *wdd, */ sbsa_gwdt_reg_write(((u64)gwdt->clk / 2) * timeout, gwdt); + /* +* Some watchdog hardware has a race condition where it will ignore +* sbsa_gwdt_keepalive() if it is called at the exact moment that a +* timeout occurs and WS0 is being asserted. Unfortunately, the default
+ * behavior of the watchdog core is very likely to trigger this race + * when action=0 because it programs WOR to be half of the desired + * timeout, andwatchdog_next_keepalive()chooses the exact same time to
+ * send keepalive pings.
+ *
+ * This triggers a race wheresbsa_gwdt_keepalive()can be called right
+ * as WS0 is being asserted, and affected hardware will ignore that + * write and continue to assert WS0. After another (timeout / 2) + * seconds, the same race happens again. If the driver wins then the + * explicit refresh will reset WS0 to false but if the hardware wins,
+ * then WS1 is asserted and the system resets.
+ *
+ * Avoid the problem by scheduling keepalive heartbeats one second + * earlier than the WOR timeout.
+ *
+ * This workaround might not be needed in a future revision of the + * hardware.
+ */
+ if (gwdt->need_ws0_race_workaround)
Quoted 8 lines
Quoted 2 lines
+
wdd->timeout-= 2;
+It seems to me that this is still racy. If the ping is ignored, I would assume that this is reflected in the watchdog registers. How about reading the status if the workaround is needed and issuing another keepalive if it was ignored ? Or just always issue a second write to
SBSA_GWDT_WRRin that case, maybe after some short delay ?
The window for the race is very small, so triggering the refresh a full second earlier should be plenty of time. Are you worried that the refresh will be delayed by a second and hit the race window anyway? I'd have to check with MediaTek when it is okay to read the status registers to check whether another refresh is needed and whether we need to delay the read and for how long.
If it would be better, we can also work around the problem by doing the refresh *after* WS0 is triggered. We just can't do it at exactly the same time.
The other option, if you think it's okay, would be to do the refresh from the WS0 interrupt handler. I confirmed in local testing that that reliably resets WS0 and the SBSA documentation suggests that that's the intended way to do the refresh to begin with.
-- Aaron
Quoted 3 lines
Guenter
Guenter Roeck
maintainerQuoted 79 lines · Aaron Plattner
Quoted 69 lines · Guenter Roeck
Quoted 68 lines · Aaron Plattner
The MediaTek implementation of the
sbsa_gwdtwatchdog has a race condition where a write toSBSA_GWDT_WRRis ignored if it occurs while the hardware is processing a timeout refresh that asserts WS0.Detect this based on the hardware implementer and adjust
wdd->timeoutto avoid the race.Signed-off-by Aaron Plattner <[email protected]>Acked-by Timur Tabi <[email protected]>---
drivers/watchdog/sbsa_gwdt.c| 52 +++++++++++++++++++++++++++++++++---1 file changed, 49 insertions(+), 3 deletions(-)drivers/watchdog/sbsa_gwdt.c +30
-0@@ -75,11 +75,17 @@ #define SBSA_GWDT_VERSION_MASK 0xF #define SBSA_GWDT_VERSION_SHIFT 16 +#define SBSA_GWDT_IMPL_MASK 0x7FF +#define SBSA_GWDT_IMPL_SHIFT 0 +#define SBSA_GWDT_IMPL_MEDIATEK 0x426 + /*** struct sbsa_gwdt - Internal representation of the SBSA GWDT * @wdd: kernel watchdog_device structure * @clk: store the System Counter clock frequency, in Hz. * @version: store the architecture version +* @need_ws0_race_workaround: +* indicate whether to adjust wdd->timeout to avoid a race with WS0 * @refresh_base: Virtual address of the watchdog refresh frame * @control_base: Virtual address of the watchdog control frame */ @@ -87,6 +93,7 @@ struct sbsa_gwdt { struct watchdog_device wdd; u32 clk; int version; + bool need_ws0_race_workaround; void __iomem *refresh_base; void __iomem *control_base; };@@ -161,6 +168,31 @@ static int sbsa_gwdt_set_timeout(struct watchdog_device *wdd,*/ sbsa_gwdt_reg_write(((u64)gwdt->clk / 2) * timeout, gwdt); + /* + * Some watchdog hardware has a race condition where it will ignore + * sbsa_gwdt_keepalive() if it is called at the exact moment that a + * timeout occurs and WS0 is being asserted. Unfortunately, the default + * behavior of the watchdog core is very likely to trigger this race + * when action=0 because it programs WOR to be half of the desired + * timeout, and watchdog_next_keepalive() chooses the exact same time to + * send keepalive pings. + * + * This triggers a race where sbsa_gwdt_keepalive() can be called right + * as WS0 is being asserted, and affected hardware will ignore that + * write and continue to assert WS0. After another (timeout / 2) + * seconds, the same race happens again. If the driver wins then the + * explicit refresh will reset WS0 to false but if the hardware wins, + * then WS1 is asserted and the system resets. + * + * Avoid the problem by scheduling keepalive heartbeats one second + * earlier than the WOR timeout. + * + * This workaround might not be needed in a future revision of the + * hardware. + */ + if (gwdt->need_ws0_race_workaround)Quoted 8 lines
drivers/watchdog/sbsa_gwdt.c static int sbsa_gwdt_set_timeout(struct watchdog_device *wdd, · line 195
Quoted 2 lines
drivers/watchdog/sbsa_gwdt.c +2
-0+ wdd->timeout -= 2; +It seems to me that this is still racy. If the ping is ignored, I would assume that this is reflected in the watchdog registers. How about reading the status if the workaround is needed and issuing another keepalive if it was ignored ? Or just always issue a second write to
SBSA_GWDT_WRRin that case, maybe after some short delay ?
Quoted 2 lines
The window for the race is very small, so triggering the refresh a full second earlier should be plenty of time. Are you worried that the refresh will be delayed by a second and hit the race window anyway? I'd have to check with MediaTek when it is okay to read the status registers to check whether another refresh is needed and whether we need to delay the read and for how long.
I am concerned about hacking ->timeout which will be passed to userspace. Also, that change does not guarantee that the heartbeat will npt be issued at the wrong time, it just reduces its probability.
How about setting min_hw_heartbeat_ms to a value slightly larger than timeout / 2 ?
Guenter