usb: ehci-mx6: Add i.MX95 OTG support
Subsystems (2)
PATCH RESEND 1/1 usb: ehci-mx6: Add i.MX95 OTG support
When the usb node is defined dr_mode="otg" ehci_usb_phy_mode() is called to determine the mode from status registers.
The IMX95RM does not currently define the USBNC STATUS register but it is assumed to be an omission as the first three registers are defined. It has been expirimentally verified that the USBNC_PHY_STATUS register at offset 0x23C bit4 (USBNC_PHYSTATUS_ID_DIG) reads 0 when USB_ID is GND and 1 when floating.
Add imx95 to the list of SoC's that determine role based on the USBNC_PHY_STATUS register.
--- drivers/usb/host/ehci-mx6.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/usb/host/ehci-mx6.c +1 -1
@@ -537,7 +537,7 @@ static int ehci_usb_phy_mode(struct udevice *dev) plat->init_type =USB_INIT_DEVICE ; else plat->init_type = USB_INIT_HOST; - }else if (is_mx7 () ||is_imx8mm () ||is_imx8mn () ||is_imx93 ()) { + }else if (is_mx7 () ||is_imx8mm () ||is_imx8mn () ||is_imx93 () ||is_imx95 ()) { phy_status = (void __iomem *)(addr +USBNC_PHY_STATUS_OFFSET ); val =readl (phy_status);
Signature · 1 line
2.25.1
Hi Tim,
I tend to replace is_imx93() || is_imx95() with is_imx9() because this driver works for iMX91, iMX93 and iMX95.
Best Regards,
Alice Guo
Quoted 45 lines
-----邮件原件-----
发件人: Tim Harvey <[email protected]>
发送时间: 2025年7月9日 23:23
收件人: [email protected]
抄送: Marek Vasut <[email protected]>; Fabio Estevam <[email protected]>; Alice Guo (OSS) <[email protected]>; dl-uboot-imx <[email protected]>; Peng Fan <[email protected]>; Stefano Babic <[email protected]>; Ye Li <[email protected]>; Tom Rini <[email protected]>; [email protected]
主题: [RESEND PATCH] usb: ehci-mx6: Add i.MX95 OTG supportWhen the usb node is defined dr_mode="otg"
ehci_usb_phy_mode()is called to determine the mode from status registers.The IMX95RM does not currently define the USBNC STATUS register but it is assumed to be an omission as the first three registers are defined. It has been expirimentally verified that the
USBNC_PHY_STATUSregister at offset0x23Cbit4 (USBNC_PHYSTATUS_ID_DIG) reads 0 whenUSB_IDis GND and 1 when floating.Add imx95 to the list of SoC's that determine role based on the
USBNC_PHY_STATUSregister.Fixes 801b5fafd35d "(usb: ehci-mx6: Add i.MX95 support")Signed-off-by Tim Harvey <[email protected]>--- drivers/usb/host/ehci-mx6.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/usb/host/ehci-mx6.c index renamed from drivers/usb/host/ehci-mx6.c +0
-0
a8748cef7ad2..f979ff8dde1e100644drivers/usb/host/ehci-mx6.c +2
-2@@ -537,7 +537,7 @@ static int ehci_usb_phy_mode(struct udevice *dev) plat->init_type =USB_INIT_DEVICE ; else plat->init_type = USB_INIT_HOST; - }else if (is_mx7 () ||is_imx8mm () ||is_imx8mn () ||is_imx93 ()) { + }else if (is_mx7 () ||is_imx8mm () ||is_imx8mn () ||is_imx93 () || +is_imx95 ()) { phy_status = (void __iomem *)(addr +USBNC_PHY_STATUS_OFFSET ); val =readl (phy_status); --2.25.1