Skip to contentSkip to conversation

phy: phy-imx8mq-usb: Add support for i.MX95 USB3 PHY

PATCH RESEND In review Tim Harvey 2 participants 2 messages Jul 9, 2025 – Aug 4, 2025

Subsystems (2)
lore
Share & tools
lore

Tim Harvey

author
#0 lore raw

PATCH RESEND 1/1 phy: phy-imx8mq-usb: Add support for i.MX95 USB3 PHY

Add initial support for i.MX95 USB.30 PHY, which is similar to the i.MX8MQ and i.MX8MP USB PHY.

The i.MX95 USB3 PHY has a Type-C Assist block (TCA) consisting of two functional blocks (XBar assist and VBus assist) and is documented in the i.MX95 RM Chapter 163.3.8 Type-C assist (TCA) block.

Instead of relying on an external MUX for Type-C plug orientation the XBar can handle the flip internally.

Add initial support for i.MX95 by:
- allowing the driver to be enabled i.MX95
- resetting the XBar
- configuring the TCA in System Configuration mode (which was determined to be necessary to enable the PHY in device-mode)

Follow-on support will need to be added to steer the XBar based on either board design (if only one pair is brought out) or if used with a Type-C controller.

---
 drivers/phy/Kconfig          |  6 +--
 drivers/phy/phy-imx8mq-usb.c | 91 +++++++++++++++++++++++++++++++++++-
 2 files changed, 93 insertions(+), 4 deletions(-)
drivers/phy/Kconfig +3 -3
index d3fe90d939e8..9f0c2bf04c4e 100644
@@ -280,11 +280,11 @@ config PHY_NPCM_USB
 	  Support the USB PHY in NPCM SoCs
 
 config PHY_IMX8MQ_USB
-	bool "NXP i.MX8MQ/i.MX8MP USB PHY Driver"
+	bool "NXP i.MX8MQ/i.MX8MP/i.MX95 USB PHY Driver"
 	depends on PHY
-	depends on IMX8MQ || IMX8MP
+	depends on IMX8MQ || IMX8MP || IMX95
 	help
-	  Support the USB3.0 PHY in NXP i.MX8MQ or i.MX8MP SoC
+	  Support the USB3.0 PHY in NXP i.MX8MQ, i.MX8MP, and i.MX95 SoC
 
 config PHY_IMX8M_PCIE
 	bool "NXP i.MX8MM/i.MX8MP PCIe PHY Driver"
drivers/phy/phy-imx8mq-usb.c +90 -1

132 lines not on this page · raw message

Signature · 1 line
2.25.1
Tested-by Alice Guo on v1 1/1
#1 lore raw
Quoted 26 lines

-----邮件原件-----
发件人: Tim Harvey <[email protected]>
发送时间: 2025年7月9日 23:24
收件人: [email protected]
抄送: Marek Vasut <[email protected]>; Fabio Estevam <[email protected]>; Alice Guo (OSS) <[email protected]>; dl-uboot-imx <[email protected]>; Peng Fan <[email protected]>; Stefano Babic <[email protected]>; Ye Li <[email protected]>; Tom Rini <[email protected]>; [email protected] 主题: [RESEND PATCH] phy: phy-imx8mq-usb: Add support for i.MX95 USB3 PHY

Add initial support for i.MX95 USB.30 PHY, which is similar to the i.MX8MQ and i.MX8MP USB PHY.

The i.MX95 USB3 PHY has a Type-C Assist block (TCA) consisting of two functional blocks (XBar assist and VBus assist) and is documented in the i.MX95 RM Chapter 163.3.8 Type-C assist (TCA) block.

Instead of relying on an external MUX for Type-C plug orientation the XBar can handle the flip internally.

Add initial support for i.MX95 by:
- allowing the driver to be enabled i.MX95
- resetting the XBar
- configuring the TCA in System Configuration mode (which was determined to be necessary to enable the PHY in device-mode)

Quoted 4 lines

Follow-on support will need to be added to steer the XBar based on either board design (if only one pair is brought out) or if used with a Type-C controller.

Best Regards,
Alice Guo