Add reaction control in rti
Subsystems (2)
v4 cover Add reaction control in rti
This allows for reaction control in rti driver. Since AM62L SoC [0] does not have WWD reset output routed to a ESM module like all other K3 SoC's and has the reset output signal routed to the reset HW block, add a new compatible for AM62L and configure reset reaction for AM62L SoC instead of NMI.
This patch has been tested on AM62L EVM [1].
Changes since v3:
- Expected default reaction for watchdog is HW reset line, so check for NMI and set reaction to NMI if exists, else default to HW reset.
v3: https://lore.kernel.org/linux-devicetree/[email protected]/
v2: https://lore.kernel.org/linux-devicetree/[email protected]/
v1-resend: https://lore.kernel.org/linux-devicetree/[email protected]/
v1: https://lore.kernel.org/linux-devicetree/[email protected]/
[0] https://www.ti.com/product/AM62L
[1] https://www.ti.com/tool/TMDS62LEVM
Judith Mendez (2):
dt-bindings: watchdog: ti,rti-wdt: Add ti,am62l-rti-wdt compatible
watchdog: rti_wdt: Add reaction control
.../bindings/watchdog/ti,rti-wdt.yaml | 1 + drivers/watchdog/rti_wdt.c | 32 ++++++++++++++++--- 2 files changed, 29 insertions(+), 4 deletions(-)
Signature · 1 line
2.49.0
PATCH v4 1/2 dt-bindings: watchdog: ti,rti-wdt: Add ti,am62l-rti-wdt compatible
Add a new compatible ti,am62l-rti-wdt for am62l SoC [0].
[0] https://www.ti.com/product/AM62L
--- Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml +1 -0
@@ -23,6 +23,7 @@ allOf: properties: compatible: enum: + - ti,am62l-rti-wdt - ti,j7-rti-wdt reg:
Signature · 1 line
2.49.0
PATCH v4 2/2 watchdog: rti_wdt: Add reaction control
In reply to Judith MendezThis allows to configure reaction between NMI and reset for WWD.
On K3 SoC's other than AM62L SoC [0], watchdog reset output is routed to the ESM module which can subsequently route the signal to safety master or SoC reset. On AM62L, the watchdog reset output is routed to the SoC HW reset block. So, add a new compatible for AM62l to add SoC data and configure reaction to reset instead of NMI.
[0] https://www.ti.com/product/AM62L
--- drivers/watchdog/rti_wdt.c | 32 ++++++++++++++++++++++++++++---- 1 file changed, 28 insertions(+), 4 deletions(-)
drivers/watchdog/rti_wdt.c +28 -4
@@ -35,7 +35,8 @@#define RTIWWDRXCTRL 0xa4#define RTIWWDSIZECTRL 0xa8 -#define RTIWWDRX_NMI 0xa +#define RTIWWDRXN_RST 0x5 +#define RTIWWDRXN_NMI 0xa#define RTIWWDSIZE_50P 0x50#define RTIWWDSIZE_25P 0x500
@@ -63,22 +64,29 @@static int heartbeat; +struct rti_wdt_data { +bool nmi; +}; +/* * struct to hold data for each WDT device * @base - base io address of WD device * @freq - source clock frequency of WDT * @wdd - hold watchdog device as is in WDT core +* @data - hold configuration data */ struct rti_wdt_device {void __iomem *base;unsigned long freq;struct watchdog_device wdd; +const struct rti_wdt_data *data; };static int rti_wdt_start (struct watchdog_device *wdd) {u32 timer_margin;struct rti_wdt_device *wdt =watchdog_get_drvdata (wdd); +u8 reaction;int ret; ret =pm_runtime_resume_and_get (wdd->parent);
@@ -101,8 +109,13 @@ static int rti_wdt_start(struct watchdog_device *wdd)*/ wdd->min_hw_heartbeat_ms =520 * wdd->timeout +MAX_HW_ERROR ; -/* Generate NMI when wdt expires */ -writel_relaxed (RTIWWDRX_NMI , wdt->base +RTIWWDRXCTRL ); +/* Reset device if wdt serviced outside of window or generate NMI if available */ +if (wdt->data->nmi) + reaction =RTIWWDRXN_NMI ; +else + reaction =RTIWWDRXN_RST ; + +writel_relaxed (reaction, wdt->base +RTIWWDRXCTRL );/* Open window size 50%; this is the largest window size available */ writel_relaxed (RTIWWDSIZE_50P , wdt->base +RTIWWDSIZECTRL );
@@ -255,6 +268,8 @@ static int rti_wdt_probe(struct platform_device *pdev) wdd->timeout =DEFAULT_HEARTBEAT ; wdd->parent = dev; + wdt->data =device_get_match_data (dev); +watchdog_set_drvdata (wdd, wdt);watchdog_set_nowayout (wdd,1 );watchdog_set_restart_priority (wdd,128 );
@@ -369,8 +384,17 @@ static void rti_wdt_remove(struct platform_device *pdev)pm_runtime_disable (&pdev->dev); } +static struct rti_wdt_data j7_wdt = { + .nmi = true, +}; + +static struct rti_wdt_data am62l_wdt = { + .nmi = false, +}; +static const struct of_device_id rti_wdt_of_match[] = { - { .compatible ="ti,j7-rti-wdt" , }, + { .compatible ="ti,j7-rti-wdt" , .data = &j7_wdt }, + { .compatible ="ti,am62l-rti-wdt" , .data = &am62l_wdt }, {}, };MODULE_DEVICE_TABLE (of, rti_wdt_of_match);
Signature · 1 line
2.49.0