Skip to contentSkip to conversation

phy: dp83869: fix interrupts issue when using with an optical fiber sfp. to correctly clear the interrupts both status registers must be read.

PATCH In review [email protected] 4 participants 4 messages Jul 26, 2025

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 phy: dp83869: fix interrupts issue when using with an optical fiber sfp. to correctly clear the interrupts both status registers must be read.

From: Anis Chali <[email protected]>

from datasheet of dp83869hm
7.3.6 Interrupt
The DP83869HM can be configured to generate an interrupt when changes of internal status occur. The interrupt allows a MAC to act upon the status in the PHY without polling the PHY registers. The interrupt source can be selected through the interrupt registers, MICR (12h) and FIBER_INT_EN (C18h). The interrupt status can be read from ISR (13h) and FIBER_INT_STTS (C19h) registers. Some interrupts are enabled by default and can be disabled through register access. Both the interrupt status registers must be read in order to clear pending interrupts. Until the pending interrupts are cleared, new interrupts may not be routed to the interrupt pin.

Fixes 01db923e8377 ("net: phy: dp83869: Add TI dp83869 phy")
---
 drivers/net/phy/dp83869.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/net/phy/dp83869.c +7 -0
index a62cd838a9ea..1e8c20f387b8 100644
@@ -41,6 +41,7 @@
 #define DP83869_IO_MUX_CFG	0x0170
 #define DP83869_OP_MODE		0x01df
 #define DP83869_FX_CTRL		0x0c00
+#define DP83869_FX_INT_STS		0x0c19
 
 #define DP83869_SW_RESET	BIT(15)
 #define DP83869_SW_RESTART	BIT(14)
@@ -195,6 +196,12 @@ static int dp83869_ack_interrupt(struct phy_device *phydev)
 	if (err < 0)
 		return err;
 
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported)) {
+		err = phy_read_mmd(phydev, DP83869_DEVADDR, DP83869_FX_INT_STS);
+		if (err < 0)
+			return err;		
+	}
+
 	return 0;
 }
 
Signature · 1 line
2.49.0
maintainer
#1 lore raw

First of all, please read:
https://www.kernel.org/doc/html/next/process/maintainer-netdev.html

Quoted 1 line

Subject: [PATCH net] phy: dp83869: fix interrupts issue when using with an optical fiber sfp. to correctly clear the interrupts both status registers must be read.

The first line of the commit message becomes the subject, it should be a very short summary of the patch (100 chars max)

Quoted 10 lines · On Fri, 25 Jul 2025 20:10:34 -0400 [email protected] wrote:

From: Anis Chali <[email protected]>

from datasheet of dp83869hm
7.3.6 Interrupt
The DP83869HM can be configured to generate an interrupt when changes of internal status occur. The interrupt allows a MAC to act upon the status in the PHY without polling the PHY registers. The interrupt source can be selected through the interrupt registers, MICR (12h) and FIBER_INT_EN (C18h). The interrupt status can be read from ISR (13h) and FIBER_INT_STTS (C19h) registers. Some interrupts are enabled by default and can be disabled through register access. Both the interrupt status registers must be read in order to clear pending interrupts. Until the pending interrupts are cleared, new interrupts may not be routed to the interrupt pin.

This needs to be line wrapped at 70-ish characters.

Quoted 2 lines
Fixes 01db923e8377 ("net: phy: dp83869: Add TI dp83869 phy")

no empty lines between tags, please

Quoted 2 lines
Signature · 1 line
pw-bot: cr
maintainer
#2 lore raw
In reply to [email protected]
Quoted 8 lines · On Fri, Jul 25, 2025 at 08:10:34PM -0400, [email protected] wrote:

From: Anis Chali <[email protected]>

from datasheet of dp83869hm
7.3.6 Interrupt
The DP83869HM can be configured to generate an interrupt when changes of internal status occur. The interrupt allows a MAC to act upon the status in the PHY without polling the PHY registers. The interrupt source can be selected through the interrupt registers, MICR (12h) and FIBER_INT_EN (C18h). The interrupt status can be read from ISR (13h) and FIBER_INT_STTS (C19h) registers.

Reading this description, it sounds like the fibre interrupt it not cascaded into the micr? There are two completely different sets of registers.

So i seems like you should be reading this register in dp83869_handle_interrupt() same as the MICR.

Andrew

---
pw-bot: cr

reviewer
#3 lore raw
In reply to [email protected]
Quoted 32 lines · On Fri, Jul 25, 2025 at 08:10:34PM -0400, [email protected] wrote:

From: Anis Chali <[email protected]>

from datasheet of dp83869hm
7.3.6 Interrupt
The DP83869HM can be configured to generate an interrupt when changes of internal status occur. The interrupt allows a MAC to act upon the status in the PHY without polling the PHY registers. The interrupt source can be selected through the interrupt registers, MICR (12h) and FIBER_INT_EN (C18h). The interrupt status can be read from ISR (13h) and FIBER_INT_STTS (C19h) registers. Some interrupts are enabled by default and can be disabled through register access. Both the interrupt status registers must be read in order to clear pending interrupts. Until the pending interrupts are cleared, new interrupts may not be routed to the interrupt pin.

Fixes 01db923e8377 ("net: phy: dp83869: Add TI dp83869 phy")
---
 drivers/net/phy/dp83869.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/net/phy/dp83869.c +1 -0
index a62cd838a9ea..1e8c20f387b8 100644
@@ -41,6 +41,7 @@
 #define DP83869_IO_MUX_CFG	0x0170
 #define DP83869_OP_MODE		0x01df
 #define DP83869_FX_CTRL		0x0c00
+#define DP83869_FX_INT_STS		0x0c19
 
 #define DP83869_SW_RESET	BIT(15)
 #define DP83869_SW_RESTART	BIT(14)

drivers/net/phy/dp83869.c static int dp83869_ack_interrupt(struct phy_device *phydev) · line 202

Quoted 7 lines
drivers/net/phy/dp83869.c +4 -0
@@ -195,6 +196,12 @@ static int dp83869_ack_interrupt(struct phy_device *phydev)
 	if (err < 0)
 		return err;
 
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported)) {
+		err = phy_read_mmd(phydev, DP83869_DEVADDR, DP83869_FX_INT_STS);
+		if (err < 0)
+			return err;		

Hi Anis,

Its invisible, of course, but the line above has trailing whitespace.

Flagged by checkpatch.

Quoted 9 lines
drivers/net/phy/dp83869.c +2 -0
+	}
+
 	return 0;
 }
 
Signature · 1 line
2.49.0