sunxi: assorted fixes to DRAM and clock init
Subsystems (3)
cover sunxi: assorted fixes to DRAM and clock init
Some assorted fixes for bugs I found while debugging and researching the boot and DRAM init process on some chips.
Patch 1 and 2 fix bugs hidden by the fact that the code in question would ever be compiled for arm64 only, but for an experiment I compiled the A133 SPL for 32-bit, which revealed those issues.
Patch 3 fixes the mode register setup for the H616 boards with LPDDR3, this was found when wrapping the mode register accesses into some functions, for a later cleanup patch.
Please have a look!
Cheers,
Andre
Andre Przywara (3):
sunxi: a133: dram: fix data type for address variable
sunxi: spl: initialise timer before clocks
sunxi: H616: dram: fix LPDDR3 mode register settings
arch/arm/mach-sunxi/board.c | 2 +- arch/arm/mach-sunxi/dram_sun50i_a133.c | 2 +- arch/arm/mach-sunxi/dram_sun50i_h616.c | 12 ++++++------ 3 files changed, 8 insertions(+), 8 deletions(-)
Signature · 1 line
2.46.3
PATCH 1/3 sunxi: a133: dram: fix data type for address variable
Variables holding addresses are typically using the "long" C type in U-Boot, to be easily compatible with both 32-bit and 64-bit builds.
The A133 DRAM driver is typically compiled for AArch64, so u64 is the same type as unsigned long, but that breaks when compiling the DRAM driver in AArch32 (for some experiments).
Fix the type to make the code more portable.
--- arch/arm/mach-sunxi/dram_sun50i_a133.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-sunxi/dram_sun50i_a133.c +1 -1
@@ -416,7 +416,7 @@ static void mctl_com_init(const struct dram_para *para,static void mctl_drive_odt_config (const struct dram_para *para) {u32 val; -u64 base; +ulong base;u32 i;/* DX drive */
Signature · 1 line
2.46.3
Re: [PATCH 1/3] sunxi: a133: dram: fix data type for address variable
Dne sobota, 2. avgust 2025 ob 01:49:16 Srednjeevropski poletni čas je Andre Przywara napisal(a):
Quoted 10 lines
Variables holding addresses are typically using the "long" C type in U-Boot, to be easily compatible with both 32-bit and 64-bit builds.
The A133 DRAM driver is typically compiled for AArch64, so u64 is the same type as unsigned long, but that breaks when compiling the DRAM driver in AArch32 (for some experiments).
Fix the type to make the code more portable.
Signed-off-by Andre Przywara <[email protected]>
Best regards,
Jernej
Quoted 18 lines
--- arch/arm/mach-sunxi/dram_sun50i_a133.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/mach-sunxi/dram_sun50i_a133.c +1
-1@@ -416,7 +416,7 @@ static void mctl_com_init(const struct dram_para *para,static void mctl_drive_odt_config (const struct dram_para *para) {u32 val; -u64 base; +ulong base;u32 i;/* DX drive */
PATCH 2/3 sunxi: spl: initialise timer before clocks
In reply to Andre PrzywaraRecent changes in the H6 clock code added delay() calls into the SPL clock setup routine, which requires the timers to work. When compiling for AArch64, we are always using the Arm Generic Timer (aka. arch timer), which does not require further setup, hence having an empty timer_init() routine.
However for 32-bit SoCs we use the Allwinner timers, which require some setup routine, and hence we need timer_init() to be called before clock_init().
Swap the order of the two calls, to be more robust when compiling the H6 clock code for AArch32 or when using the Allwinner timers for whatever reason.
--- arch/arm/mach-sunxi/board.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-sunxi/board.c +1 -1
@@ -476,8 +476,8 @@ void board_init_f(ulong dummy)/* Enable non-secure access to some peripherals */ tzpc_init (); -clock_init ();timer_init (); +clock_init ();gpio_init ();spl_init ();
Signature · 1 line
2.46.3
Jernej Škrabec
maintainerRe: [PATCH 2/3] sunxi: spl: initialise timer before clocks
Dne sobota, 2. avgust 2025 ob 01:49:17 Srednjeevropski poletni čas je Andre Przywara napisal(a):
Quoted 23 lines
Recent changes in the H6 clock code added
delay()calls into the SPL clock setup routine, which requires the timers to work. When compiling for AArch64, we are always using the Arm Generic Timer (aka. arch timer), which does not require further setup, hence having an emptytimer_init()routine.
However for 32-bit SoCs we use the Allwinner timers, which require some setup routine, and hence we needtimer_init()to be called beforeclock_init().Swap the order of the two calls, to be more robust when compiling the H6 clock code for AArch32 or when using the Allwinner timers for whatever reason.
Signed-off-by Andre Przywara <[email protected]>--- arch/arm/mach-sunxi/board.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/mach-sunxi/board.c +0
-0
arch/arm/mach-sunxi/board.c void board_init_f(ulong dummy) · line 480
Quoted 6 lines
arch/arm/mach-sunxi/board.c +1
-1@@ -476,8 +476,8 @@ void board_init_f(ulong dummy)/* Enable non-secure access to some peripherals */ tzpc_init (); -clock_init ();timer_init (); +clock_init ();
I contemplated similar change in past. It works fine for 64-bit architectures, but I'm unsure for 32-bit. If you take a look at A83t clock code, it uses sdelay() exactly because timer is not initialized at that time.
So, are you sure that this change has no unwanted side effects?
Best regards,
Jernej
Quoted 4 lines
arch/arm/mach-sunxi/board.c +0
-0gpio_init ();spl_init ();
Re: [PATCH 2/3] sunxi: spl: initialise timer before clocks
Quoted 35 lines · On Mon, 11 Aug 2025 17:34:47 +0200 Jernej Škrabec <[email protected]>…
Dne sobota, 2. avgust 2025 ob 01:49:17 Srednjeevropski poletni čas je Andre Przywara napisal(a):
Quoted 23 lines
Recent changes in the H6 clock code added
delay()calls into the SPL clock setup routine, which requires the timers to work. When compiling for AArch64, we are always using the Arm Generic Timer (aka. arch timer), which does not require further setup, hence having an emptytimer_init()routine.
However for 32-bit SoCs we use the Allwinner timers, which require some setup routine, and hence we needtimer_init()to be called beforeclock_init().Swap the order of the two calls, to be more robust when compiling the H6 clock code for AArch32 or when using the Allwinner timers for whatever reason.
Signed-off-by Andre Przywara <[email protected]>--- arch/arm/mach-sunxi/board.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/mach-sunxi/board.c +0
-0arch/arm/mach-sunxi/board.c void board_init_f(ulong dummy) · line 480
Quoted 6 lines
arch/arm/mach-sunxi/board.c +1
-1@@ -476,8 +476,8 @@ void board_init_f(ulong dummy)/* Enable non-secure access to some peripherals */ tzpc_init (); -clock_init ();timer_init (); +clock_init ();I contemplated similar change in past. It works fine for 64-bit architectures, but I'm unsure for 32-bit. If you take a look at A83t clock code, it uses
sdelay()exactly because timer is not initialized at that time.
Quoted 1 line
So, are you sure that this change has no unwanted side effects?
No, I am not ;-)
I was about to test this on some more boards. But I think with the change in that direction, the only issue would be if the timer_init() code relies on the clocks being set up already. And since timer_init() is only *one* rather small function, just doing MMIO accesses, I think the risk is quite low.
Thanks for having a look anyway, I will report back how the test goes.
Cheers,
Andre
Quoted 9 lines
Quoted 5 lines
arch/arm/mach-sunxi/board.c +0
-0gpio_init ();spl_init ();
Jernej Škrabec
maintainerRe: [PATCH 2/3] sunxi: spl: initialise timer before clocks
Dne ponedeljek, 11. avgust 2025 ob 17:52:25 Srednjeevropski poletni čas je Andre Przywara napisal(a):
Quoted 38 lines
Quoted 35 lines · On Mon, 11 Aug 2025 17:34:47 +0200 Jernej Škrabec <[email protected]>…
Dne sobota, 2. avgust 2025 ob 01:49:17 Srednjeevropski poletni čas je Andre Przywara napisal(a):
Quoted 23 lines
Recent changes in the H6 clock code added
delay()calls into the SPL clock setup routine, which requires the timers to work. When compiling for AArch64, we are always using the Arm Generic Timer (aka. arch timer), which does not require further setup, hence having an emptytimer_init()routine.
However for 32-bit SoCs we use the Allwinner timers, which require some setup routine, and hence we needtimer_init()to be called beforeclock_init().Swap the order of the two calls, to be more robust when compiling the H6 clock code for AArch32 or when using the Allwinner timers for whatever reason.
Signed-off-by Andre Przywara <[email protected]>--- arch/arm/mach-sunxi/board.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/mach-sunxi/board.c +0
-0arch/arm/mach-sunxi/board.c void board_init_f(ulong dummy) · line 480
Quoted 6 lines
arch/arm/mach-sunxi/board.c +1
-1@@ -476,8 +476,8 @@ void board_init_f(ulong dummy)/* Enable non-secure access to some peripherals */ tzpc_init (); -clock_init ();timer_init (); +clock_init ();I contemplated similar change in past. It works fine for 64-bit architectures, but I'm unsure for 32-bit. If you take a look at A83t clock code, it uses
sdelay()exactly because timer is not initialized at that time.
Quoted 8 lines
Quoted 1 line
So, are you sure that this change has no unwanted side effects?
No, I am not ;-)
I was about to test this on some more boards. But I think with the change in that direction, the only issue would be if thetimer_init()code relies on the clocks being set up already. And sincetimer_init()is only *one* rather small function, just doing MMIO accesses, I think the risk is quite low.
As long as clock function doesn't need to enable bus or module clock, everything should be fine. Quick check didn't show any such code so it is probably safe to switch.
Best regards,
Jernej
Quoted 17 lines
Thanks for having a look anyway, I will report back how the test goes.
Cheers,
AndreQuoted 9 lines
Quoted 5 lines
arch/arm/mach-sunxi/board.c +0
-0gpio_init ();spl_init ();
Re: [PATCH 2/3] sunxi: spl: initialise timer before clocks
In reply to Andre PrzywaraOn Mon, 11 Aug 2025 16:52:25 +0100
Andre Przywara <[email protected]> wrote:
Hi,
Quoted 40 lines
Quoted 35 lines · On Mon, 11 Aug 2025 17:34:47 +0200 Jernej Škrabec <[email protected]>…
Dne sobota, 2. avgust 2025 ob 01:49:17 Srednjeevropski poletni čas je Andre Przywara napisal(a):
Quoted 23 lines
Recent changes in the H6 clock code added
delay()calls into the SPL clock setup routine, which requires the timers to work. When compiling for AArch64, we are always using the Arm Generic Timer (aka. arch timer), which does not require further setup, hence having an emptytimer_init()routine.
However for 32-bit SoCs we use the Allwinner timers, which require some setup routine, and hence we needtimer_init()to be called beforeclock_init().Swap the order of the two calls, to be more robust when compiling the H6 clock code for AArch32 or when using the Allwinner timers for whatever reason.
Signed-off-by Andre Przywara <[email protected]>--- arch/arm/mach-sunxi/board.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/mach-sunxi/board.c +0
-0arch/arm/mach-sunxi/board.c void board_init_f(ulong dummy) · line 480
Quoted 6 lines
arch/arm/mach-sunxi/board.c +1
-1@@ -476,8 +476,8 @@ void board_init_f(ulong dummy)/* Enable non-secure access to some peripherals */ tzpc_init (); -clock_init ();timer_init (); +clock_init ();I contemplated similar change in past. It works fine for 64-bit architectures, but I'm unsure for 32-bit. If you take a look at A83t clock code, it uses
sdelay()exactly because timer is not initialized at that time.Quoted 1 line
So, are you sure that this change has no unwanted side effects?
Quoted 8 lines
No, I am not ;-)
I was about to test this on some more boards. But I think with the change in that direction, the only issue would be if thetimer_init()code relies on the clocks being set up already. And sincetimer_init()is only *one* rather small function, just doing MMIO accesses, I think the risk is quite low.Thanks for having a look anyway, I will report back how the test goes.
Alright, I booted this patch on:
A10, A20, A33, V40, A80, A83T, T113s3, F1C100s, H3 (/me puts the mini-USB cables back into the shelf now)
For the A83T specifically, as a test, I replaced the sdelay() calls with udelay() ones, and it hangs with mainline, but works with this patch.
So unless someone speaks up now, I am tempted to merge this patch.
Cheers,
Andre
Re: [PATCH 2/3] sunxi: spl: initialise timer before clocks
In reply to Andre PrzywaraDne sobota, 2. avgust 2025 ob 01:49:17 Srednjeevropski poletni čas je Andre Przywara napisal(a):
Quoted 9 lines
Recent changes in the H6 clock code added
delay()calls into the SPL clock setup routine, which requires the timers to work. When compiling for AArch64, we are always using the Arm Generic Timer (aka. arch timer), which does not require further setup, hence having an emptytimer_init()routine.
However for 32-bit SoCs we use the Allwinner timers, which require some setup routine, and hence we needtimer_init()to be called beforeclock_init().
Quoted 5 lines
Swap the order of the two calls, to be more robust when compiling the H6 clock code for AArch32 or when using the Allwinner timers for whatever reason.
Signed-off-by Andre Przywara <[email protected]>
Best regards,
Jernej
Quoted 19 lines
--- arch/arm/mach-sunxi/board.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/mach-sunxi/board.c +1
-1@@ -476,8 +476,8 @@ void board_init_f(ulong dummy)/* Enable non-secure access to some peripherals */ tzpc_init (); -clock_init ();timer_init (); +clock_init ();gpio_init ();spl_init ();
PATCH 3/3 sunxi: H616: dram: fix LPDDR3 mode register settings
In reply to Andre PrzywaraThe JEDEC LPDDR3 spec defines mode register 0 (MR0) as being read-only, so there is no point in trying to set its value.
Also the H616 memory controller encodes the mode register index to be written starting from bit 8 in MRCTRL1 (for LPDDR3 and LPDDR4 chips), so we need to OR in that number to tell the controller which MR to program.
On top of that, the mode registers between DDR3 and LPDDR3 are completely different, so writing values crafted for DDR3 into a LPDDR3 chip is just wrong. Due to the above mentioned bugs the writes for MR0-MR2 did not have any effect (as they were all trying to set the read-only MR0), so the mode registers just stayed unchanged.
Looking at the LPDDR3 spec and the BSP code, let's write the proper MR values into LPDDR3 chips, using the proper addressing mode. Use the opportunity to document the LPDDR3 mode register bits written.
--- arch/arm/mach-sunxi/dram_sun50i_h616.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)
arch/arm/mach-sunxi/dram_sun50i_h616.c +6 -6
@@ -1078,18 +1078,18 @@ static bool mctl_phy_init(const struct dram_para *para,mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 );break ;case SUNXI_DRAM_TYPE_LPDDR3 : -writel (mr0, &mctl_ctl->mrctrl1); -writel (0x800000f0 , &mctl_ctl->mrctrl0); -mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 ); - -writel (4 , &mctl_ctl->mrctrl1); +/* MR0 is read-only */ +/* MR1: nWR=14, BL8 */ +writel (0x183 , &mctl_ctl->mrctrl1);writel (0x800000f0 , &mctl_ctl->mrctrl0);mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 ); -writel (mr2, &mctl_ctl->mrctrl1); +/* MR2: no WR leveling, WL set A, use nWR>9, nRL=14/nWL=8 */ +writel (0x21c , &mctl_ctl->mrctrl1);writel (0x800000f0 , &mctl_ctl->mrctrl0);mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 ); +/* MR3: 34.3 Ohm pull-up/pull-down resistor */ writel (0x301 , &mctl_ctl->mrctrl1);writel (0x800000f0 , &mctl_ctl->mrctrl0);mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 );
Signature · 1 line
2.46.3
Jernej Škrabec
maintainerRe: [PATCH 3/3] sunxi: H616: dram: fix LPDDR3 mode register settings
Dne sobota, 2. avgust 2025 ob 01:49:18 Srednjeevropski poletni čas je Andre Przywara napisal(a):
Quoted 11 lines
The JEDEC LPDDR3 spec defines mode register 0 (MR0) as being read-only, so there is no point in trying to set its value.
Also the H616 memory controller encodes the mode register index to be written starting from bit 8 in MRCTRL1 (for LPDDR3 and LPDDR4 chips), so we need to OR in that number to tell the controller which MR to program.On top of that, the mode registers between DDR3 and LPDDR3 are completely different, so writing values crafted for DDR3 into a LPDDR3 chip is just wrong. Due to the above mentioned bugs the writes for MR0-MR2 did not have any effect (as they were all trying to set the read-only MR0), so the mode registers just stayed unchanged.
Nice catch! Looking at BSP DRAM code, it only sets MR1, MR2 and MR3.
Quoted 3 lines
Looking at the LPDDR3 spec and the BSP code, let's write the proper MR values into LPDDR3 chips, using the proper addressing mode.
Please explain how you find those values. Are they always set in this way for all boards using LPDDR3?
Best regards,
Jernej
Quoted 37 lines
Use the opportunity to document the LPDDR3 mode register bits written.
Signed-off-by Andre Przywara <[email protected]>--- arch/arm/mach-sunxi/dram_sun50i_h616.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)arch/arm/mach-sunxi/dram_sun50i_h616.c +6
-6@@ -1078,18 +1078,18 @@ static bool mctl_phy_init(const struct dram_para *para,mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 );break ;case SUNXI_DRAM_TYPE_LPDDR3 : -writel (mr0, &mctl_ctl->mrctrl1); -writel (0x800000f0 , &mctl_ctl->mrctrl0); -mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 ); - -writel (4 , &mctl_ctl->mrctrl1); +/* MR0 is read-only */ +/* MR1: nWR=14, BL8 */ +writel (0x183 , &mctl_ctl->mrctrl1);writel (0x800000f0 , &mctl_ctl->mrctrl0);mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 ); -writel (mr2, &mctl_ctl->mrctrl1); +/* MR2: no WR leveling, WL set A, use nWR>9, nRL=14/nWL=8 */ +writel (0x21c , &mctl_ctl->mrctrl1);writel (0x800000f0 , &mctl_ctl->mrctrl0);mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 ); +/* MR3: 34.3 Ohm pull-up/pull-down resistor */ writel (0x301 , &mctl_ctl->mrctrl1);writel (0x800000f0 , &mctl_ctl->mrctrl0);mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 );
Re: [PATCH 3/3] sunxi: H616: dram: fix LPDDR3 mode register settings
On Mon, 11 Aug 2025 17:49:06 +0200
Jernej Škrabec <[email protected]> wrote:
Hi Jernej,
many thanks for having a look!
Quoted 13 lines
Dne sobota, 2. avgust 2025 ob 01:49:18 Srednjeevropski poletni čas je Andre Przywara napisal(a):
Quoted 11 lines
The JEDEC LPDDR3 spec defines mode register 0 (MR0) as being read-only, so there is no point in trying to set its value.
Also the H616 memory controller encodes the mode register index to be written starting from bit 8 in MRCTRL1 (for LPDDR3 and LPDDR4 chips), so we need to OR in that number to tell the controller which MR to program.On top of that, the mode registers between DDR3 and LPDDR3 are completely different, so writing values crafted for DDR3 into a LPDDR3 chip is just wrong. Due to the above mentioned bugs the writes for MR0-MR2 did not have any effect (as they were all trying to set the read-only MR0), so the mode registers just stayed unchanged.
Quoted 8 lines
Nice catch! Looking at BSP DRAM code, it only sets MR1, MR2 and MR3.
Quoted 3 lines
Looking at the LPDDR3 spec and the BSP code, let's write the proper MR values into LPDDR3 chips, using the proper addressing mode.
Please explain how you find those values. Are they always set in this way for all boards using LPDDR3?
Yeah, that's a good question! At first, I tried using what JEDEC describes as the default settings, but that didn't work. Then I looked into some parameters found in some BSP image dumps, but that didn't work either. JEDEC describes those MRs as write-only, and I haven't tried whether reading them would work nevertheless, not sure about the exact algorithm for reading MRs anyway.
What eventually worked was to use the BSP values written by exactly the boot0 on the eMMC that boots an LPDDR3 system - which is actually only one in mainline: the Tanix TX1.
So yeah, those values work for me (TM), and there is only one LPDDR3 board supported, so fingers crossed. But actually I wonder if those MR values really belong into the timing routine (mctl_set_timing_params(), since parts depend on the speed bin. I see some other SoC/DRAM type combinations doing that already (H6 DDR3/LPDDR3 and A523 LPDDR4), maybe we should follow suit here?
Cheers,
Andre
Quoted 45 lines
Best regards,
JernejQuoted 37 lines
Use the opportunity to document the LPDDR3 mode register bits written.
Signed-off-by Andre Przywara <[email protected]>--- arch/arm/mach-sunxi/dram_sun50i_h616.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)arch/arm/mach-sunxi/dram_sun50i_h616.c +6
-6@@ -1078,18 +1078,18 @@ static bool mctl_phy_init(const struct dram_para *para,mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 );break ;case SUNXI_DRAM_TYPE_LPDDR3 : -writel (mr0, &mctl_ctl->mrctrl1); -writel (0x800000f0 , &mctl_ctl->mrctrl0); -mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 ); - -writel (4 , &mctl_ctl->mrctrl1); +/* MR0 is read-only */ +/* MR1: nWR=14, BL8 */ +writel (0x183 , &mctl_ctl->mrctrl1);writel (0x800000f0 , &mctl_ctl->mrctrl0);mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 ); -writel (mr2, &mctl_ctl->mrctrl1); +/* MR2: no WR leveling, WL set A, use nWR>9, nRL=14/nWL=8 */ +writel (0x21c , &mctl_ctl->mrctrl1);writel (0x800000f0 , &mctl_ctl->mrctrl0);mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 ); +/* MR3: 34.3 Ohm pull-up/pull-down resistor */ writel (0x301 , &mctl_ctl->mrctrl1);writel (0x800000f0 , &mctl_ctl->mrctrl0);mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 );
Re: [PATCH 3/3] sunxi: H616: dram: fix LPDDR3 mode register settings
Dne ponedeljek, 11. avgust 2025 ob 18:08:16 Srednjeevropski poletni čas je Andre Przywara napisal(a):
Quoted 39 lines
On Mon, 11 Aug 2025 17:49:06 +0200
Jernej Škrabec <[email protected]> wrote:Hi Jernej,
many thanks for having a look!
Quoted 13 lines
Dne sobota, 2. avgust 2025 ob 01:49:18 Srednjeevropski poletni čas je Andre Przywara napisal(a):
Quoted 11 lines
The JEDEC LPDDR3 spec defines mode register 0 (MR0) as being read-only, so there is no point in trying to set its value.
Also the H616 memory controller encodes the mode register index to be written starting from bit 8 in MRCTRL1 (for LPDDR3 and LPDDR4 chips), so we need to OR in that number to tell the controller which MR to program.On top of that, the mode registers between DDR3 and LPDDR3 are completely different, so writing values crafted for DDR3 into a LPDDR3 chip is just wrong. Due to the above mentioned bugs the writes for MR0-MR2 did not have any effect (as they were all trying to set the read-only MR0), so the mode registers just stayed unchanged.
Quoted 8 lines
Nice catch! Looking at BSP DRAM code, it only sets MR1, MR2 and MR3.
Quoted 3 lines
Looking at the LPDDR3 spec and the BSP code, let's write the proper MR values into LPDDR3 chips, using the proper addressing mode.
Please explain how you find those values. Are they always set in this way for all boards using LPDDR3?
Yeah, that's a good question! At first, I tried using what JEDEC describes as the default settings, but that didn't work. Then I looked into some parameters found in some BSP image dumps, but that didn't work either. JEDEC describes those MRs as write-only, and I haven't tried whether reading them would work nevertheless, not sure about the exact algorithm for reading MRs anyway.
What eventually worked was to use the BSP values written by exactly the boot0 on the eMMC that boots an LPDDR3 system - which is actually only one in mainline: the Tanix TX1.
Quoted 6 lines
So yeah, those values work for me (TM), and there is only one LPDDR3 board supported, so fingers crossed. But actually I wonder if those MR values really belong into the timing routine (
mctl_set_timing_params(), since parts depend on the speed bin. I see some other SoC/DRAM type combinations doing that already (H6 DDR3/LPDDR3 and A523 LPDDR4), maybe we should follow suit here?
Historically, I checked several boards and if MR value was the same in all configs, I just hardcoded the value. While this is a bit naive, it works most of the time. There are some cases where it is set dynamically in BSP code. Those cases can be a bit annoying to find. Ideally, MR values shout be Kconfig option with default values.
It's up to you to decide which approach to take. Since it affects just one board and changes were tested:
Best regards,
Jernej
Quoted 52 lines
Cheers,
AndreQuoted 45 lines
Best regards,
JernejQuoted 37 lines
Use the opportunity to document the LPDDR3 mode register bits written.
Signed-off-by Andre Przywara <[email protected]>--- arch/arm/mach-sunxi/dram_sun50i_h616.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)arch/arm/mach-sunxi/dram_sun50i_h616.c +6
-6@@ -1078,18 +1078,18 @@ static bool mctl_phy_init(const struct dram_para *para,mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 );break ;case SUNXI_DRAM_TYPE_LPDDR3 : -writel (mr0, &mctl_ctl->mrctrl1); -writel (0x800000f0 , &mctl_ctl->mrctrl0); -mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 ); - -writel (4 , &mctl_ctl->mrctrl1); +/* MR0 is read-only */ +/* MR1: nWR=14, BL8 */ +writel (0x183 , &mctl_ctl->mrctrl1);writel (0x800000f0 , &mctl_ctl->mrctrl0);mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 ); -writel (mr2, &mctl_ctl->mrctrl1); +/* MR2: no WR leveling, WL set A, use nWR>9, nRL=14/nWL=8 */ +writel (0x21c , &mctl_ctl->mrctrl1);writel (0x800000f0 , &mctl_ctl->mrctrl0);mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 ); +/* MR3: 34.3 Ohm pull-up/pull-down resistor */ writel (0x301 , &mctl_ctl->mrctrl1);writel (0x800000f0 , &mctl_ctl->mrctrl0);mctl_await_completion (&mctl_ctl->mrctrl0,BIT (31 ),0 );