spacemit: introduce P1 PMIC support
Subsystems (6)
v12 cover spacemit: introduce P1 PMIC support
The SpacemiT P1 is an I2C-controlled PMIC that implements 6 buck converters and 12 LDOs. It contains a load switch, ADC channels, GPIOs, a real-time clock, and a watchdog timer.
This series introduces a multifunction driver for the P1 PMIC as well as drivers for its regulators and RTC.
The content of this version is identical to the previous one. It has simply been rebased onto Linux v6.17-rc1.
-Alex
This series is available here:
https://github.com/riscstar/linux/tree/outgoing/pmic-v12
Between version 11 and version 12:
- Simple rebase
Here is version 11 of this series:
https://lore.kernel.org/lkml/[email protected]/
Between version 10 and version 11:
- Abandon trying to implement a simple_mfd_data->max_register field
- Fix a missing dependency pointed out by the kernel test robot
Here is version 10 of this series:
https://lore.kernel.org/lkml/[email protected]/
Between version 9 and version 10:
- The #address-cells and #size-cells for the i2c8 DTS node were moved into its primary definition in "k1.dtsi".
- The interrupts property for the i2c8 DTS node was moved below its clock-related properties.
- The status property in the pmic@41 DTS node was dropped.
- The function that provides the regmap_config structure to use was reworked a bit.
- A new function was added to free the regmap_config structure after it's no longer needed.
Here is version 9 of this series:
https://lore.kernel.org/lkml/[email protected]/
Between version 8 and version 9:
- The max_config value is always used if it is provided with the simple_mfd_data structure.
- The regmap_config structure used is allocated dynamically if necessary; otherwise regmap_config_8r_8v is used.
- A small duplicated comment is removed
Here is version 8 of this series:
https://lore.kernel.org/lkml/[email protected]/
More complete history is available at that link.
Alex Elder (7):
dt-bindings: mfd: add support the SpacemiT P1 PMIC
mfd: simple-mfd-i2c: add SpacemiT P1 support
regulator: spacemit: support SpacemiT P1 regulators
rtc: spacemit: support the SpacemiT P1 RTC
riscv: dts: spacemit: enable the i2c8 adapter
riscv: dts: spacemit: define fixed regulators
riscv: dts: spacemit: define regulator constraints
.../devicetree/bindings/mfd/spacemit,p1.yaml | 86 +++++++++ .../boot/dts/spacemit/k1-bananapi-f3.dts | 135 ++++++++++++++ arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi | 7 + arch/riscv/boot/dts/spacemit/k1.dtsi | 13 ++ drivers/mfd/Kconfig | 11 ++ drivers/mfd/simple-mfd-i2c.c | 18 ++ drivers/regulator/Kconfig | 13 ++ drivers/regulator/Makefile | 1 + drivers/regulator/spacemit-p1.c | 157 ++++++++++++++++ drivers/rtc/Kconfig | 10 ++ drivers/rtc/Makefile | 1 + drivers/rtc/rtc-spacemit-p1.c | 167 ++++++++++++++++++ 12 files changed, 619 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/spacemit,p1.yaml create mode 100644 drivers/regulator/spacemit-p1.c create mode 100644 drivers/rtc/rtc-spacemit-p1.c
base-commit: 8f5ae30d69d7543eee0d70083daf4de8fe15d585
Signature · 1 line
2.48.1
PATCH v12 1/7 dt-bindings: mfd: add support the SpacemiT P1 PMIC
Enable the SpacemiT P1, which is an I2C-controlled PMIC. Initially only the RTC and regulators will be supported.
--- .../devicetree/bindings/mfd/spacemit,p1.yaml | 86 +++++++++++++++++++ 1 file changed, 86 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/spacemit,p1.yaml
Documentation/devicetree/bindings/mfd/spacemit,p1.yaml new file +86 -0
@@ -0,0 +1,86 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/spacemit,p1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SpacemiT P1 Power Management Integrated Circuit + +maintainers: + - Troy Mitchell <[email protected]> + +description: + P1 is an I2C-controlled PMIC produced by SpacemiT. It implements six + constant-on-time buck converters and twelve low-dropout regulators. + It also contains a load switch, watchdog timer, real-time clock, eight + 12-bit ADC channels, and six GPIOs. Additional details are available + in the "Power Stone/P1" section at the following link. + https://developer.spacemit.com/documentation + +properties: + compatible: + const: spacemit,p1 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vin-supply: + description: Input supply phandle. + + regulators: + type: object + + patternProperties: + "^(buck[1-6]|aldo[1-4]|dldo[1-7])$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@41 { + compatible = "spacemit,p1"; + reg = <0x41>; + interrupts = <64>; + + regulators { + buck1 { + regulator-name = "buck1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3450000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + aldo1 { + regulator-name = "aldo1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + }; + + dldo1 { + regulator-name = "dldo1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + }; + }; + }; + };
Signature · 1 line
2.48.1
Re: [PATCH v12 1/7] dt-bindings: mfd: add support the SpacemiT P1 PMIC
Quoted 16 lines · Alex Elder
Enable the SpacemiT P1, which is an I2C-controlled PMIC. Initially only the RTC and regulators will be supported.
Signed-off-by Alex Elder <[email protected]>Reviewed-by Rob Herring (Arm) <[email protected]>--- .../devicetree/bindings/mfd/spacemit,p1.yaml | 86 +++++++++++++++++++ 1 file changed, 86 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/spacemit,p1.yamlDocumentation/devicetree/bindings/mfd/spacemit,p1.yaml new file +0
-0
Documentation/devicetree/bindings/mfd/spacemit,p1.yaml line 10
Quoted 10 lines
Documentation/devicetree/bindings/mfd/spacemit,p1.yaml new file +10
-0@@ -0,0 +1,86 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/spacemit,p1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SpacemiT P1 Power Management Integrated Circuit + +maintainers: + - Troy Mitchell <[email protected]>
You can change it from this to my company email:
[email protected]
- Troy
Quoted 79 lines
Documentation/devicetree/bindings/mfd/spacemit,p1.yaml new file +76
-0+ +description: + P1 is an I2C-controlled PMIC produced by SpacemiT. It implements six + constant-on-time buck converters and twelve low-dropout regulators. + It also contains a load switch, watchdog timer, real-time clock, eight + 12-bit ADC channels, and six GPIOs. Additional details are available + in the "Power Stone/P1" section at the following link. + https://developer.spacemit.com/documentation + +properties: + compatible: + const: spacemit,p1 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vin-supply: + description: Input supply phandle. + + regulators: + type: object + + patternProperties: + "^(buck[1-6]|aldo[1-4]|dldo[1-7])$": + type: object + $ref: /schemas/regulator/regulator.yaml# + unevaluatedProperties: false + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@41 { + compatible = "spacemit,p1"; + reg = <0x41>; + interrupts = <64>; + + regulators { + buck1 { + regulator-name = "buck1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3450000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + aldo1 { + regulator-name = "aldo1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + }; + + dldo1 { + regulator-name = "dldo1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + }; + }; + }; + };Signature · 1 line
2.48.1
Re: [PATCH v12 1/7] dt-bindings: mfd: add support the SpacemiT P1 PMIC
Quoted 6 lines · Troy Mitchell
You can change it from this to my company email:
[email protected]Acked-by Troy Mitchell<[email protected]>- Troy
I will make this change before I do a final version. -Alex
PATCH v12 2/7 mfd: simple-mfd-i2c: add SpacemiT P1 support
In reply to Alex ElderEnable support for the RTC and regulators found in the SpacemiT P1 PMIC. Support is implemented by the simple I2C MFD driver.
The P1 PMIC is normally implemented with the SpacemiT K1 SoC. This PMIC provides 6 buck converters and 12 LDO regulators. It also implements a switch, watchdog timer, real-time clock, and more. Initially its RTC and regulators are supported.
--- drivers/mfd/Kconfig | 11 +++++++++++ drivers/mfd/simple-mfd-i2c.c | 18 ++++++++++++++++++ 2 files changed, 29 insertions(+)
drivers/mfd/Kconfig +11 -0
@@ -1238,6 +1238,17 @@ config MFD_QCOM_RPM Say M here if you want to include support for the Qualcomm RPM as a module. This will build a module called "qcom_rpm". +config MFD_SPACEMIT_P1 + tristate "SpacemiT P1 PMIC" + depends on I2C + select MFD_SIMPLE_MFD_I2C + help + This option supports the I2C-based SpacemiT P1 PMIC, which + contains regulators, a power switch, GPIOs, an RTC, and more. + This option is selected when any of the supported sub-devices + is configured. The basic functionality is implemented by the + simple MFD I2C driver. + config MFD_SPMI_PMIC tristate "Qualcomm SPMI PMICs" depends on ARCH_QCOM || COMPILE_TEST
drivers/mfd/simple-mfd-i2c.c +18 -0
@@ -93,12 +93,30 @@ static const struct simple_mfd_data maxim_mon_max77705 = { .mfd_cell_size = ARRAY_SIZE(max77705_sensor_cells), }; + +static const struct regmap_config spacemit_p1_regmap_config = { + .reg_bits =8 , + .val_bits =8 , +}; + +static const struct mfd_cell spacemit_p1_cells[] = { + { .name ="spacemit-p1-regulator" , }, + { .name ="spacemit-p1-rtc" , }, +}; + +static const struct simple_mfd_data spacemit_p1 = { + .regmap_config = &spacemit_p1_regmap_config, + .mfd_cell = spacemit_p1_cells, + .mfd_cell_size =ARRAY_SIZE (spacemit_p1_cells), +}; +static const struct of_device_id simple_mfd_i2c_of_match[] = { { .compatible ="kontron,sl28cpld" }, { .compatible ="silergy,sy7636a" , .data = &silergy_sy7636a}, { .compatible ="maxim,max5970" , .data = &maxim_max5970}, { .compatible ="maxim,max5978" , .data = &maxim_max5970}, { .compatible ="maxim,max77705-battery" , .data = &maxim_mon_max77705}, + { .compatible ="spacemit,p1" , .data = &spacemit_p1, }, {} };MODULE_DEVICE_TABLE (of, simple_mfd_i2c_of_match);
Signature · 1 line
2.48.1
Troy Mitchell
reviewerRe: [PATCH v12 2/7] mfd: simple-mfd-i2c: add SpacemiT P1 support
Hi, Alex,
I did not find any accesses to the P1 shutdown or reboot registers here. Does this mean that the current series does not support reboot or shutdown? If so, do you have any plans to support this functionality?
If I have misunderstood, please correct me.
Best regards,
Troy
Quoted 79 lines · Alex Elder
Enable support for the RTC and regulators found in the SpacemiT P1 PMIC. Support is implemented by the simple I2C MFD driver.
The P1 PMIC is normally implemented with the SpacemiT K1 SoC. This PMIC provides 6 buck converters and 12 LDO regulators. It also implements a switch, watchdog timer, real-time clock, and more. Initially its RTC and regulators are supported.
Signed-off-by Alex Elder <[email protected]>--- drivers/mfd/Kconfig | 11 +++++++++++ drivers/mfd/simple-mfd-i2c.c | 18 ++++++++++++++++++ 2 files changed, 29 insertions(+)drivers/mfd/Kconfig +11
-0@@ -1238,6 +1238,17 @@ config MFD_QCOM_RPM Say M here if you want to include support for the Qualcomm RPM as a module. This will build a module called "qcom_rpm". +config MFD_SPACEMIT_P1 + tristate "SpacemiT P1 PMIC" + depends on I2C + select MFD_SIMPLE_MFD_I2C + help + This option supports the I2C-based SpacemiT P1 PMIC, which + contains regulators, a power switch, GPIOs, an RTC, and more. + This option is selected when any of the supported sub-devices + is configured. The basic functionality is implemented by the + simple MFD I2C driver. + config MFD_SPMI_PMIC tristate "Qualcomm SPMI PMICs" depends on ARCH_QCOM || COMPILE_TESTdrivers/mfd/simple-mfd-i2c.c +18
-0@@ -93,12 +93,30 @@ static const struct simple_mfd_data maxim_mon_max77705 = { .mfd_cell_size = ARRAY_SIZE(max77705_sensor_cells), }; + +static const struct regmap_config spacemit_p1_regmap_config = { + .reg_bits =8 , + .val_bits =8 , +}; + +static const struct mfd_cell spacemit_p1_cells[] = { + { .name ="spacemit-p1-regulator" , }, + { .name ="spacemit-p1-rtc" , }, +}; + +static const struct simple_mfd_data spacemit_p1 = { + .regmap_config = &spacemit_p1_regmap_config, + .mfd_cell = spacemit_p1_cells, + .mfd_cell_size =ARRAY_SIZE (spacemit_p1_cells), +}; +static const struct of_device_id simple_mfd_i2c_of_match[] = { { .compatible ="kontron,sl28cpld" }, { .compatible ="silergy,sy7636a" , .data = &silergy_sy7636a}, { .compatible ="maxim,max5970" , .data = &maxim_max5970}, { .compatible ="maxim,max5978" , .data = &maxim_max5970}, { .compatible ="maxim,max77705-battery" , .data = &maxim_mon_max77705}, + { .compatible ="spacemit,p1" , .data = &spacemit_p1, }, {} };MODULE_DEVICE_TABLE (of, simple_mfd_i2c_of_match);Signature · 7 lines
2.48.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Re: [PATCH v12 2/7] mfd: simple-mfd-i2c: add SpacemiT P1 support
Quoted 4 lines · Troy Mitchell
Hi, Alex,
I did not find any accesses to the P1 shutdown or reboot registers here. Does this mean that the current series does not support reboot or shutdown?
Yes, that is correct.
Quoted 1 line
If so, do you have any plans to support this functionality?
At this time I personally don't have any plans to add this, but it could be added later (by anyone).
I actually attempted to do this initially, but gave up. The PMIC is accessed via I2C, and I needed to implement a non-blocking version of the I2C register write operation. I tried that, but then found that the shutdown or reboot still did not work reliably. As it was, this was more than I originally planned to do, so I just implemented the simple RTC operations instead.
-Alex
Quoted 86 lines
If I have misunderstood, please correct me.
Best regards,
TroyQuoted 79 lines · Alex Elder
Enable support for the RTC and regulators found in the SpacemiT P1 PMIC. Support is implemented by the simple I2C MFD driver.
The P1 PMIC is normally implemented with the SpacemiT K1 SoC. This PMIC provides 6 buck converters and 12 LDO regulators. It also implements a switch, watchdog timer, real-time clock, and more. Initially its RTC and regulators are supported.
Signed-off-by Alex Elder <[email protected]>--- drivers/mfd/Kconfig | 11 +++++++++++ drivers/mfd/simple-mfd-i2c.c | 18 ++++++++++++++++++ 2 files changed, 29 insertions(+)drivers/mfd/Kconfig +11
-0@@ -1238,6 +1238,17 @@ config MFD_QCOM_RPM Say M here if you want to include support for the Qualcomm RPM as a module. This will build a module called "qcom_rpm". +config MFD_SPACEMIT_P1 + tristate "SpacemiT P1 PMIC" + depends on I2C + select MFD_SIMPLE_MFD_I2C + help + This option supports the I2C-based SpacemiT P1 PMIC, which + contains regulators, a power switch, GPIOs, an RTC, and more. + This option is selected when any of the supported sub-devices + is configured. The basic functionality is implemented by the + simple MFD I2C driver. + config MFD_SPMI_PMIC tristate "Qualcomm SPMI PMICs" depends on ARCH_QCOM || COMPILE_TESTdrivers/mfd/simple-mfd-i2c.c +18
-0@@ -93,12 +93,30 @@ static const struct simple_mfd_data maxim_mon_max77705 = { .mfd_cell_size = ARRAY_SIZE(max77705_sensor_cells), }; + +static const struct regmap_config spacemit_p1_regmap_config = { + .reg_bits =8 , + .val_bits =8 , +}; + +static const struct mfd_cell spacemit_p1_cells[] = { + { .name ="spacemit-p1-regulator" , }, + { .name ="spacemit-p1-rtc" , }, +}; + +static const struct simple_mfd_data spacemit_p1 = { + .regmap_config = &spacemit_p1_regmap_config, + .mfd_cell = spacemit_p1_cells, + .mfd_cell_size =ARRAY_SIZE (spacemit_p1_cells), +}; +static const struct of_device_id simple_mfd_i2c_of_match[] = { { .compatible ="kontron,sl28cpld" }, { .compatible ="silergy,sy7636a" , .data = &silergy_sy7636a}, { .compatible ="maxim,max5970" , .data = &maxim_max5970}, { .compatible ="maxim,max5978" , .data = &maxim_max5970}, { .compatible ="maxim,max77705-battery" , .data = &maxim_mon_max77705}, + { .compatible ="spacemit,p1" , .data = &spacemit_p1, }, {} };MODULE_DEVICE_TABLE (of, simple_mfd_i2c_of_match);Signature · 7 lines
2.48.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Troy Mitchell
reviewerRe: [PATCH v12 2/7] mfd: simple-mfd-i2c: add SpacemiT P1 support
Quoted 8 lines · Alex Elder
Quoted 4 lines · Troy Mitchell
Hi, Alex,
I did not find any accesses to the P1 shutdown or reboot registers here. Does this mean that the current series does not support reboot or shutdown?
Yes, that is correct.
Quoted 8 lines
Quoted 1 line
If so, do you have any plans to support this functionality?
At this time I personally don't have any plans to add this, but it could be added later (by anyone).
I actually attempted to do this initially, but gave up. The PMIC is accessed via I2C, and I needed to implement a non-blocking version of the I2C register write operation. I tried that,
You tried that? so that means you have implemented a non-blocking version of the I2C?
If so, can you give me a source tree to test it?
Quoted 2 lines
but
then found that the shutdown or reboot still did not work reliably.
ditto.
- Troy
Quoted 91 lines
As it was, this was more than I originally planned to do, so I just implemented the simple RTC operations instead.
-Alex
Quoted 84 lines
If I have misunderstood, please correct me.
Best regards,
TroyQuoted 77 lines · Alex Elder
Enable support for the RTC and regulators found in the SpacemiT P1 PMIC. Support is implemented by the simple I2C MFD driver.
The P1 PMIC is normally implemented with the SpacemiT K1 SoC. This PMIC provides 6 buck converters and 12 LDO regulators. It also implements a switch, watchdog timer, real-time clock, and more. Initially its RTC and regulators are supported.
Signed-off-by Alex Elder <[email protected]>--- drivers/mfd/Kconfig | 11 +++++++++++ drivers/mfd/simple-mfd-i2c.c | 18 ++++++++++++++++++ 2 files changed, 29 insertions(+)drivers/mfd/Kconfig +11
-0@@ -1238,6 +1238,17 @@ config MFD_QCOM_RPM Say M here if you want to include support for the Qualcomm RPM as a module. This will build a module called "qcom_rpm". +config MFD_SPACEMIT_P1 + tristate "SpacemiT P1 PMIC" + depends on I2C + select MFD_SIMPLE_MFD_I2C + help + This option supports the I2C-based SpacemiT P1 PMIC, which + contains regulators, a power switch, GPIOs, an RTC, and more. + This option is selected when any of the supported sub-devices + is configured. The basic functionality is implemented by the + simple MFD I2C driver. + config MFD_SPMI_PMIC tristate "Qualcomm SPMI PMICs" depends on ARCH_QCOM || COMPILE_TESTdrivers/mfd/simple-mfd-i2c.c +18
-0@@ -93,12 +93,30 @@ static const struct simple_mfd_data maxim_mon_max77705 = { .mfd_cell_size = ARRAY_SIZE(max77705_sensor_cells), }; + +static const struct regmap_config spacemit_p1_regmap_config = { + .reg_bits =8 , + .val_bits =8 , +}; + +static const struct mfd_cell spacemit_p1_cells[] = { + { .name ="spacemit-p1-regulator" , }, + { .name ="spacemit-p1-rtc" , }, +}; + +static const struct simple_mfd_data spacemit_p1 = { + .regmap_config = &spacemit_p1_regmap_config, + .mfd_cell = spacemit_p1_cells, + .mfd_cell_size =ARRAY_SIZE (spacemit_p1_cells), +}; +static const struct of_device_id simple_mfd_i2c_of_match[] = { { .compatible ="kontron,sl28cpld" }, { .compatible ="silergy,sy7636a" , .data = &silergy_sy7636a}, { .compatible ="maxim,max5970" , .data = &maxim_max5970}, { .compatible ="maxim,max5978" , .data = &maxim_max5970}, { .compatible ="maxim,max77705-battery" , .data = &maxim_mon_max77705}, + { .compatible ="spacemit,p1" , .data = &spacemit_p1, }, {} };MODULE_DEVICE_TABLE (of, simple_mfd_i2c_of_match);Signature · 7 lines
2.48.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Troy Mitchell
reviewerRe: [PATCH v12 2/7] mfd: simple-mfd-i2c: add SpacemiT P1 support
In reply to Alex ElderQuoted 8 lines · Alex Elder
Quoted 4 lines · Troy Mitchell
Hi, Alex,
I did not find any accesses to the P1 shutdown or reboot registers here. Does this mean that the current series does not support reboot or shutdown?
Yes, that is correct.
Quoted 8 lines
Quoted 1 line
If so, do you have any plans to support this functionality?
At this time I personally don't have any plans to add this, but it could be added later (by anyone).
I actually attempted to do this initially, but gave up. The PMIC is accessed via I2C, and I needed to implement a non-blocking version of the I2C register write operation. I tried that, but
I have implemented a non-blocking version of the I2C driver [1]
Link:
https://lore.kernel.org/all/[email protected]/
[1]
- Troy
Quoted 92 lines
then found that the shutdown or reboot still did not work reliably. As it was, this was more than I originally planned to do, so I just implemented the simple RTC operations instead.
-Alex
Quoted 84 lines
If I have misunderstood, please correct me.
Best regards,
TroyQuoted 77 lines · Alex Elder
Enable support for the RTC and regulators found in the SpacemiT P1 PMIC. Support is implemented by the simple I2C MFD driver.
The P1 PMIC is normally implemented with the SpacemiT K1 SoC. This PMIC provides 6 buck converters and 12 LDO regulators. It also implements a switch, watchdog timer, real-time clock, and more. Initially its RTC and regulators are supported.
Signed-off-by Alex Elder <[email protected]>--- drivers/mfd/Kconfig | 11 +++++++++++ drivers/mfd/simple-mfd-i2c.c | 18 ++++++++++++++++++ 2 files changed, 29 insertions(+)drivers/mfd/Kconfig +11
-0@@ -1238,6 +1238,17 @@ config MFD_QCOM_RPM Say M here if you want to include support for the Qualcomm RPM as a module. This will build a module called "qcom_rpm". +config MFD_SPACEMIT_P1 + tristate "SpacemiT P1 PMIC" + depends on I2C + select MFD_SIMPLE_MFD_I2C + help + This option supports the I2C-based SpacemiT P1 PMIC, which + contains regulators, a power switch, GPIOs, an RTC, and more. + This option is selected when any of the supported sub-devices + is configured. The basic functionality is implemented by the + simple MFD I2C driver. + config MFD_SPMI_PMIC tristate "Qualcomm SPMI PMICs" depends on ARCH_QCOM || COMPILE_TESTdrivers/mfd/simple-mfd-i2c.c +18
-0@@ -93,12 +93,30 @@ static const struct simple_mfd_data maxim_mon_max77705 = { .mfd_cell_size = ARRAY_SIZE(max77705_sensor_cells), }; + +static const struct regmap_config spacemit_p1_regmap_config = { + .reg_bits =8 , + .val_bits =8 , +}; + +static const struct mfd_cell spacemit_p1_cells[] = { + { .name ="spacemit-p1-regulator" , }, + { .name ="spacemit-p1-rtc" , }, +}; + +static const struct simple_mfd_data spacemit_p1 = { + .regmap_config = &spacemit_p1_regmap_config, + .mfd_cell = spacemit_p1_cells, + .mfd_cell_size =ARRAY_SIZE (spacemit_p1_cells), +}; +static const struct of_device_id simple_mfd_i2c_of_match[] = { { .compatible ="kontron,sl28cpld" }, { .compatible ="silergy,sy7636a" , .data = &silergy_sy7636a}, { .compatible ="maxim,max5970" , .data = &maxim_max5970}, { .compatible ="maxim,max5978" , .data = &maxim_max5970}, { .compatible ="maxim,max77705-battery" , .data = &maxim_mon_max77705}, + { .compatible ="spacemit,p1" , .data = &spacemit_p1, }, {} };MODULE_DEVICE_TABLE (of, simple_mfd_i2c_of_match);Signature · 7 lines
2.48.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
PATCH v12 3/7 regulator: spacemit: support SpacemiT P1 regulators
In reply to Alex ElderAdd support for the regulators found in the SpacemiT P1 PMIC. This PMIC provides 6 buck converters and 12 LDO regulators.
The PMIC is implemented as a multi-function device. These regulators are probed based on this driver being named in a MFD cell in the simple MFD I2C driver.
--- drivers/regulator/Kconfig | 13 +++ drivers/regulator/Makefile | 1 + drivers/regulator/spacemit-p1.c | 157 ++++++++++++++++++++++++++++++++ 3 files changed, 171 insertions(+) create mode 100644 drivers/regulator/spacemit-p1.c
drivers/regulator/Kconfig +13 -0
@@ -1395,6 +1395,19 @@ config REGULATOR_SLG51000 The SLG51000 is seven compact and customizable low dropout regulators. +config REGULATOR_SPACEMIT_P1 + tristate "SpacemiT P1 regulators" + depends on ARCH_SPACEMIT || COMPILE_TEST + depends on I2C + select MFD_SPACEMIT_P1 + default ARCH_SPACEMIT + help + Enable support for regulators implemented by the SpacemiT P1 + power controller. The P1 implements 6 high-efficiency buck + converters and 12 programmable LDO regulators. To compile this + driver as a module, choose M here. The module will be called + "spacemit-pmic". + config REGULATOR_STM32_BOOSTER tristate "STMicroelectronics STM32 BOOSTER" depends on ARCH_STM32 || COMPILE_TEST
drivers/regulator/Makefile +1 -0
@@ -162,6 +162,7 @@ obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o obj-$(CONFIG_REGULATOR_SC2731) += sc2731-regulator.o obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o obj-$(CONFIG_REGULATOR_SLG51000) += slg51000-regulator.o +obj-$(CONFIG_REGULATOR_SPACEMIT_P1) += spacemit-p1.o obj-$(CONFIG_REGULATOR_STM32_BOOSTER) += stm32-booster.o obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o obj-$(CONFIG_REGULATOR_STM32_PWR) += stm32-pwr.o
drivers/regulator/spacemit-p1.c new file +157 -0
157 lines not on this page · raw message
Signature · 1 line
2.48.1
PATCH v12 4/7 rtc: spacemit: support the SpacemiT P1 RTC
In reply to Alex ElderAdd support for the RTC found in the SpacemiT P1 PMIC. Initially only setting and reading the time are supported.
The PMIC is implemented as a multi-function device. This RTC is probed based on this driver being named in a MFD cell in the simple MFD I2C driver.
--- drivers/rtc/Kconfig | 10 ++ drivers/rtc/Makefile | 1 + drivers/rtc/rtc-spacemit-p1.c | 167 ++++++++++++++++++++++++++++++++++ 3 files changed, 178 insertions(+) create mode 100644 drivers/rtc/rtc-spacemit-p1.c
drivers/rtc/Kconfig +10 -0
@@ -406,6 +406,16 @@ config RTC_DRV_MAX77686 This driver can also be built as a module. If so, the module will be called rtc-max77686. +config RTC_DRV_SPACEMIT_P1 + tristate "SpacemiT P1 RTC" + depends on ARCH_SPACEMIT || COMPILE_TEST + select MFD_SPACEMIT_P1 + default ARCH_SPACEMIT + help + Enable support for the RTC function in the SpacemiT P1 PMIC. + This driver can also be built as a module, which will be called + "spacemit-p1-rtc". + config RTC_DRV_NCT3018Y tristate "Nuvoton NCT3018Y" depends on OF
drivers/rtc/Makefile +1 -0
@@ -171,6 +171,7 @@ obj-$(CONFIG_RTC_DRV_SD2405AL) += rtc-sd2405al.o obj-$(CONFIG_RTC_DRV_SD3078) += rtc-sd3078.o obj-$(CONFIG_RTC_DRV_SH) += rtc-sh.o obj-$(CONFIG_RTC_DRV_SNVS) += rtc-snvs.o +obj-$(CONFIG_RTC_DRV_SPACEMIT_P1) += rtc-spacemit-p1.o obj-$(CONFIG_RTC_DRV_SPEAR) += rtc-spear.o obj-$(CONFIG_RTC_DRV_STARFIRE) += rtc-starfire.o obj-$(CONFIG_RTC_DRV_STK17TA8) += rtc-stk17ta8.o
drivers/rtc/rtc-spacemit-p1.c new file +167 -0
167 lines not on this page · raw message
Signature · 1 line
2.48.1
PATCH v12 5/7 riscv: dts: spacemit: enable the i2c8 adapter
In reply to Alex ElderDefine properties for the I2C adapter that provides access to the SpacemiT P1 PMIC. Enable this adapter on the Banana Pi BPI-F3.
--- arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts | 12 ++++++++++++ arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi | 7 +++++++ arch/riscv/boot/dts/spacemit/k1.dtsi | 13 +++++++++++++ 3 files changed, 32 insertions(+)
arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts +12 -0
@@ -40,6 +40,18 @@ &emmc { status = "okay"; }; +&i2c8 { + pinctrl-0 = <&i2c8_cfg>; + pinctrl-names = "default"; + status = "okay"; + + pmic@41 { + compatible = "spacemit,p1"; + reg = <0x41>; + interrupts = <64>; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_2_cfg>;
arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi +7 -0
@@ -11,6 +11,13 @@ #define K1_GPIO(x) (x / 32) (x % 32) &pinctrl { + i2c8_cfg: i2c8-cfg { + i2c8-0-pins { + pinmux = <K1_PADCONF(93, 0)>, /* PWR_SCL */ + <K1_PADCONF(94, 0)>; /* PWR_SDA */ + }; + }; + uart0_2_cfg: uart0-2-cfg { uart0-2-pins { pinmux = <K1_PADCONF(68, 2)>,
arch/riscv/boot/dts/spacemit/k1.dtsi +13 -0
@@ -459,6 +459,19 @@ pwm7: pwm@d401bc00 { status = "disabled"; }; + i2c8: i2c@d401d800 { + compatible = "spacemit,k1-i2c"; + reg = <0x0 0xd401d800 0x0 0x38>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&syscon_apbc CLK_TWSI8>, + <&syscon_apbc CLK_TWSI8_BUS>; + clock-names = "func", "bus"; + clock-frequency = <400000>; + interrupts = <19>; + status = "disabled"; + }; + pinctrl: pinctrl@d401e000 { compatible = "spacemit,k1-pinctrl"; reg = <0x0 0xd401e000 0x0 0x400>;
Signature · 1 line
2.48.1
PATCH v12 6/7 riscv: dts: spacemit: define fixed regulators
In reply to Alex ElderDefine the DC power input and the 4v power as fixed supplies in the Banana Pi BPI-F3.
--- .../boot/dts/spacemit/k1-bananapi-f3.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts +19 -0
@@ -28,6 +28,25 @@ led1 { default-state = "on"; }; }; + + reg_dc_in: dc-in-12v { + compatible = "regulator-fixed"; + regulator-name = "dc_in_12v"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vcc_4v: vcc-4v { + compatible = "regulator-fixed"; + regulator-name = "vcc_4v"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <4000000>; + regulator-boot-on; + regulator-always-on; + vin-supply = <®_dc_in>; + }; }; &emmc {
Signature · 1 line
2.48.1
PATCH v12 7/7 riscv: dts: spacemit: define regulator constraints
In reply to Alex ElderDefine basic constraints for the regulators in the SpacemiT P1 PMIC, as implemented in the Banana Pi BPI-F3.
--- .../boot/dts/spacemit/k1-bananapi-f3.dts | 104 ++++++++++++++++++ 1 file changed, 104 insertions(+)
arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts +104 -0
@@ -68,6 +68,110 @@ pmic@41 { compatible = "spacemit,p1"; reg = <0x41>; interrupts = <64>; + vin-supply = <®_vcc_4v>; + + regulators { + buck1 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3450000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + buck2 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3450000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + buck3 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1800000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + buck4 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3300000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + buck5 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3450000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + buck6 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3450000>; + regulator-ramp-delay = <5000>; + regulator-always-on; + }; + + aldo1 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + }; + + aldo2 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + + aldo3 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + + aldo4 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + + dldo1 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + }; + + dldo2 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + + dldo3 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + + dldo4 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-always-on; + }; + + dldo5 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + + dldo6 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + regulator-always-on; + }; + + dldo7 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3400000>; + }; + }; }; };
Signature · 1 line
2.48.1