FAILED: patch "[PATCH] arm64: dts: ti: k3-j722s-evm: Fix USB gpio-hog level for" failed to apply to 6.12-stable tree
[email protected]
maintainerThe patch below does not apply to the 6.12-stable tree.
If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <[email protected]>.
To reproduce the conflict and resubmit, you may use the following commands:
git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-6.12.y
git checkout FETCH_HEAD
git cherry-pick -x 65ba2a6e77e9e5c843a591055789050e77b5c65e
# <resolve conflicts, build, test, etc.>
git commit -s
git send-email --to '<[email protected]>' --in-reply-to '2025081521-dangle-drapery-9a9a@gregkh' --subject-prefix 'PATCH 6.12.y' HEAD^..
Possible dependencies:
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From 65ba2a6e77e9e5c843a591055789050e77b5c65e Mon Sep 17 00:00:00 2001
From: Siddharth Vadapalli <[email protected]>
Date: Mon, 23 Jun 2025 15:36:57 +0530
Subject: [PATCH] arm64: dts: ti: k3-j722s-evm: Fix USB gpio-hog level for
Type-C
According to the "GPIO Expander Map / Table" section of the J722S EVM Schematic within the Evaluation Module Design Files package [0], the GPIO Pin P05 located on the GPIO Expander 1 (I2C0/0x23) has to be pulled down to select the Type-C interface. Since commit under Fixes claims to enable the Type-C interface, update the property within "p05-hog" from "output-high" to "output-low", thereby switching from the Type-A interface to the Type-C interface.
[0]: https://www.ti.com/lit/zip/sprr495
arch/arm64/boot/dts/ti/k3-j722s-evm.dts +1 -1
@@ -634,7 +634,7 @@ p05-hog { /* P05 - USB2.0_MUX_SEL */ gpio-hog; gpios = <5 GPIO_ACTIVE_LOW>; - output-high; + output-low; }; p01_hog: p01-hog {
Sasha Levin
maintainerPATCH 1/2 arm64: dts: ti: k3-j722s-evm: Fix USB2.0_MUX_SEL to select Type-C
From: Hrushikesh Salunke <[email protected]>
[ Upstream commit bc8d9e6b5821c40ab5dd3a81e096cb114939de50 ]
J722S SOC has two usb controllers USB0 and USB1. USB0 is brought out on the EVM as a stacked USB connector which has one Type-A and one Type-C port. These Type-A and Type-C ports are connected to MUX so only one of them can be enabled at a time.
Commit under Fixes, tries to enable the USB0 instance of USB to interface with the Type-C port via the USB hub, by configuring the USB2.0_MUX_SEL to GPIO_ACTIVE_HIGH. But it is observed on J722S-EVM that Type-A port is enabled instead of Type-C port.
Fix this by setting USB2.0_MUX_SEL to GPIO_ACTIVE_LOW to enable Type-C port.
Stable-dep-of: 65ba2a6e77e9 ("arm64: dts: ti: k3-j722s-evm: Fix USB gpio-hog level for Type-C")
--- arch/arm64/boot/dts/ti/k3-j722s-evm.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/ti/k3-j722s-evm.dts +1 -1
@@ -495,7 +495,7 @@ exp1: gpio@23 { p05-hog { /* P05 - USB2.0_MUX_SEL */ gpio-hog; - gpios = <5 GPIO_ACTIVE_HIGH>; + gpios = <5 GPIO_ACTIVE_LOW>; output-high; };
Signature · 1 line
2.50.1
Sasha Levin
maintainerPATCH 2/2 arm64: dts: ti: k3-j722s-evm: Fix USB gpio-hog level for Type-C
From: Siddharth Vadapalli <[email protected]>
[ Upstream commit 65ba2a6e77e9e5c843a591055789050e77b5c65e ]
According to the "GPIO Expander Map / Table" section of the J722S EVM Schematic within the Evaluation Module Design Files package [0], the GPIO Pin P05 located on the GPIO Expander 1 (I2C0/0x23) has to be pulled down to select the Type-C interface. Since commit under Fixes claims to enable the Type-C interface, update the property within "p05-hog" from "output-high" to "output-low", thereby switching from the Type-A interface to the Type-C interface.
[0]: https://www.ti.com/lit/zip/sprr495
--- arch/arm64/boot/dts/ti/k3-j722s-evm.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/ti/k3-j722s-evm.dts +1 -1
@@ -496,7 +496,7 @@ p05-hog { /* P05 - USB2.0_MUX_SEL */ gpio-hog; gpios = <5 GPIO_ACTIVE_LOW>; - output-high; + output-low; }; p01_hog: p01-hog {
Signature · 1 line
2.50.1