Skip to contentSkip to conversation

arm64: dts: rockchip: Change ethernet TXD timing delay value

PATCH In review Dongjin Kim 3 participants 4 messages Aug 19, 2025 – Oct 19

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 arm64: dts: rockchip: Change ethernet TXD timing delay value

Very poor network performance is observed on the ODROID-M1 Board (REV 1.0 20220613) when running iperf3 (under 200Mbits/sec), and this problem can be resolved after changing the value of TXD timing to 0x35 from 0x4f.

---
 arch/arm64/boot/dts/rockchip/rk3568-odroid-m1.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/rockchip/rk3568-odroid-m1.dts +1 -1
index 0f844806ec542..e1a550a04498e 100644
@@ -210,7 +210,7 @@ &gmac0_rgmii_clk
 		     &gmac0_rgmii_bus>;
 	status = "okay";
 
-	tx_delay = <0x4f>;
+	tx_delay = <0x35>;
 	rx_delay = <0x2d>;
 };
 
Signature · 1 line
2.34.1
#1 lore raw

Hi,

Quoted 4 lines

Very poor network performance is observed on the ODROID-M1 Board (REV 1.0 20220613) when running iperf3 (under 200Mbits/sec), and this problem can be resolved after changing the value of TXD timing to 0x35 from 0x4f.

Can you try changing phy-mode to "rgmii-id" ?

```
--- a/arch/arm64/boot/dts/rockchip/rk3568-odroid-m1.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-odroid-m1.dts
@@ -200,7 +200,7 @@ &gmac0 {
 	assigned-clock-rates = <0>, <125000000>;
 	clock_in_out = "output";
 	phy-handle = <&rgmii_phy0>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-supply = <&vcc3v3_sys>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac0_miim
@@ -209,9 +209,6 @@ &gmac0_rx_bus2
 		     &gmac0_rgmii_clk
 		     &gmac0_rgmii_bus>;
 	status = "okay";
-
-	tx_delay = <0x4f>;
-	rx_delay = <0x2d>;
 };
 
 &gpu {
```

--
2.25.1

#2 lore raw
Quoted 33 lines · Chukun Pan

Hi,

Quoted 4 lines

Very poor network performance is observed on the ODROID-M1 Board (REV 1.0 20220613) when running iperf3 (under 200Mbits/sec), and this problem can be resolved after changing the value of TXD timing to 0x35 from 0x4f.

Can you try changing phy-mode to "rgmii-id" ?

```

arch/arm64/boot/dts/rockchip/rk3568-odroid-m1.dts +1 -4
@@ -200,7 +200,7 @@ &gmac0 {
 	assigned-clock-rates = <0>, <125000000>;
 	clock_in_out = "output";
 	phy-handle = <&rgmii_phy0>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-supply = <&vcc3v3_sys>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac0_miim
@@ -209,9 +209,6 @@ &gmac0_rx_bus2
 		     &gmac0_rgmii_clk
 		     &gmac0_rgmii_bus>;
 	status = "okay";
-
-	tx_delay = <0x4f>;
-	rx_delay = <0x2d>;
 };
 
 &gpu {

```

Quoted 4 lines

--
2.25.1

Thank you for suggesting me to try 'rgmii-id' again.

I'd remember that 'rgmii-id' didn't work with the very early version of the board, however your suggestion works. Let me test the change with more boards and submit the new patch when it's done.

Thanks a lot.
Dongjin Kim.

#3 lore raw

Hi Dongjin,

Quoted 5 lines · Dongjin Kim

Thank you for suggesting me to try 'rgmii-id' again.

I'd remember that 'rgmii-id' didn't work with the very early version of the board, however your suggestion works. Let me test the change with more boards and submit the new patch when it's done.

I ran into the same problem on an ODROID-M1 board marked "REV 1.0 20211112", an earlier revision than the 20220613 one in your patch, running Home Assistant OS (kernel 6.18.52). With the current tx_delay = <0x4f>, about 6.6% of all TCP segments were retransmitted at 1000 Mbit/s and larger HTTP transfers stalled.

I tested Chukun's suggestion (phy-mode = "rgmii-id", with tx_delay and rx_delay removed; the driver reports "init for RGMII_ID") on the same board, on a 1000 Mbit/s full-duplex link. It works fine on this early revision as well:

- 3 retransmitted TCP segments out of 24929 (0.012%) over 3 h 49 min of uptime, and no RX/TX errors
- 90 sequential requests for large files (22.5 MB in total): no failures, 1.4 s in total, the slowest one 47 ms
- 120 parallel requests (75 MB in total): no failures, 1.2 s

For comparison, tx_delay = <0x35> gave 0.03% retransmissions on the same board.

Are you still planning to send a v3 with rgmii-id? If you don't have time for it, I'd be happy to send it with Chukun's Suggested-by. Either way, for the rgmii-id version:

Thanks,
Miguel