Skip to contentSkip to conversation

FAILED: patch "[PATCH] ata: Fix SATA_MOBILE_LPM_POLICY description in Kconfig" failed to apply to 5.15-stable tree

PATCH New [email protected] 2 participants 2 messages Aug 21, 2025

Subsystems (2)
lore
Share & tools
lore

[email protected]

author maintainer
#0 lore raw

The patch below does not apply to the 5.15-stable tree.
If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <[email protected]>.

To reproduce the conflict and resubmit, you may use the following commands:

git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-5.15.y
git checkout FETCH_HEAD
git cherry-pick -x ed62a62a18bc144f73eadf866ae46842e8f6606e
# <resolve conflicts, build, test, etc.>
git commit -s
git send-email --to '<[email protected]>' --in-reply-to '2025082137-platypus-ditzy-1762@gregkh' --subject-prefix 'PATCH 5.15.y' HEAD^..

Possible dependencies:

thanks,

greg k-h

------------------ original commit in Linus's tree ------------------

From ed62a62a18bc144f73eadf866ae46842e8f6606e Mon Sep 17 00:00:00 2001
From: Damien Le Moal <[email protected]>
Date: Wed, 18 Jun 2025 16:25:19 +0900
Subject: [PATCH] ata: Fix SATA_MOBILE_LPM_POLICY description in Kconfig

Improve the description of the possible default SATA link power management policies and add the missing description for policy 5. No functional changes.

Fixes a5ec5a7bfd1f ("ata: ahci: Support state with min power but Partial low power state")
drivers/ata/Kconfig +24 -8
index e00536b49552..120a2b7067fc 100644
@@ -117,23 +117,39 @@ config SATA_AHCI
 
 config SATA_MOBILE_LPM_POLICY
 	int "Default SATA Link Power Management policy"
-	range 0 4
+	range 0 5
 	default 3
 	depends on SATA_AHCI
 	help
 	  Select the Default SATA Link Power Management (LPM) policy to use
 	  for chipsets / "South Bridges" supporting low-power modes. Such
 	  chipsets are ubiquitous across laptops, desktops and servers.
+	  Each policy combines power saving states and features:
+	   - Partial: The Phy logic is powered but is in a reduced power
+                      state. The exit latency from this state is no longer than
+                      10us).
+	   - Slumber: The Phy logic is powered but is in an even lower power
+                      state. The exit latency from this state is potentially
+		      longer, but no longer than 10ms.
+	   - DevSleep: The Phy logic may be powered down. The exit latency from
+	               this state is no longer than 20 ms, unless otherwise
+		       specified by DETO in the device Identify Device Data log.
+	   - HIPM: Host Initiated Power Management (host automatically
+		   transitions to partial and slumber).
+	   - DIPM: Device Initiated Power Management (device automatically
+		   transitions to partial and slumber).
 
-	  The value set has the following meanings:
+	  The possible values for the default SATA link power management
+	  policies are:
 		0 => Keep firmware settings
-		1 => Maximum performance
-		2 => Medium power
-		3 => Medium power with Device Initiated PM enabled
-		4 => Minimum power
+		1 => No power savings (maximum performance)
+		2 => HIPM (Partial)
+		3 => HIPM (Partial) and DIPM (Partial and Slumber)
+		4 => HIPM (Partial and DevSleep) and DIPM (Partial and Slumber)
+		5 => HIPM (Slumber and DevSleep) and DIPM (Partial and Slumber)
 
-	  Note "Minimum power" is known to cause issues, including disk
-	  corruption, with some disks and should not be used.
+	  Excluding the value 0, higher values represent policies with higher
+	  power savings.
 
 config SATA_AHCI_PLATFORM
 	tristate "Platform AHCI SATA support"
maintainer
#1 lore raw

PATCH 1/1 ata: Fix SATA_MOBILE_LPM_POLICY description in Kconfig

From: Damien Le Moal <[email protected]>

[ Upstream commit ed62a62a18bc144f73eadf866ae46842e8f6606e ]

Improve the description of the possible default SATA link power management policies and add the missing description for policy 5. No functional changes.

Fixes a5ec5a7bfd1f ("ata: ahci: Support state with min power but Partial low power state")
[ Adjust context ]
---
 drivers/ata/Kconfig | 35 ++++++++++++++++++++++++++---------
 1 file changed, 26 insertions(+), 9 deletions(-)
drivers/ata/Kconfig +26 -9
index a7da8ea7b3ed..3630d86c74f1 100644
@@ -117,22 +117,39 @@ config SATA_AHCI
 
 config SATA_MOBILE_LPM_POLICY
 	int "Default SATA Link Power Management policy for mobile chipsets"
-	range 0 4
+	range 0 5
 	default 0
 	depends on SATA_AHCI
 	help
 	  Select the Default SATA Link Power Management (LPM) policy to use
 	  for mobile / laptop variants of chipsets / "South Bridges".
 
-	  The value set has the following meanings:
+	  Each policy combines power saving states and features:
+	   - Partial: The Phy logic is powered but is in a reduced power
+                      state. The exit latency from this state is no longer than
+                      10us).
+	   - Slumber: The Phy logic is powered but is in an even lower power
+                      state. The exit latency from this state is potentially
+		      longer, but no longer than 10ms.
+	   - DevSleep: The Phy logic may be powered down. The exit latency from
+	               this state is no longer than 20 ms, unless otherwise
+		       specified by DETO in the device Identify Device Data log.
+	   - HIPM: Host Initiated Power Management (host automatically
+		   transitions to partial and slumber).
+	   - DIPM: Device Initiated Power Management (device automatically
+		   transitions to partial and slumber).
+
+	  The possible values for the default SATA link power management
+	  policies are:
 		0 => Keep firmware settings
-		1 => Maximum performance
-		2 => Medium power
-		3 => Medium power with Device Initiated PM enabled
-		4 => Minimum power
-
-	  Note "Minimum power" is known to cause issues, including disk
-	  corruption, with some disks and should not be used.
+		1 => No power savings (maximum performance)
+		2 => HIPM (Partial)
+		3 => HIPM (Partial) and DIPM (Partial and Slumber)
+		4 => HIPM (Partial and DevSleep) and DIPM (Partial and Slumber)
+		5 => HIPM (Slumber and DevSleep) and DIPM (Partial and Slumber)
+
+	  Excluding the value 0, higher values represent policies with higher
+	  power savings.
 
 config SATA_AHCI_PLATFORM
 	tristate "Platform AHCI SATA support"
Signature · 1 line
2.50.1