Skip to contentSkip to conversation

arm64: dts: allwinner: t527: orangepi-4a: Limit eMMC clock to 75 MHz

PATCH In review Chen-Yu Tsai 2 participants 2 messages Aug 21, 2025 – Aug 27, 2025

Subsystems (2)
lore
Share & tools
lore

Chen-Yu Tsai

author maintainer
#0 lore raw

PATCH 1/1 arm64: dts: allwinner: t527: orangepi-4a: Limit eMMC clock to 75 MHz

From: Chen-Yu Tsai <[email protected]>

The eMMC on the Orange Pi 4A doesn't function correctly at full speed of 150 MHz under HS200 mode. Either the traces on the board or module aren't great, or the SoC's internal delays are incorrect. Tuning the pin drive strength did not help.

After some experimenting, 75 MHz was found to be stable enough. Use this as the maximum frequency for now.

Fixes de713ccb9934 ("arm64: dts: allwinner: t527: Add OrangePi 4A board")
---
 arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts +1 -0
index c52d09cf0888..fb5311a46c2e 100644
@@ -160,6 +160,7 @@ &mmc2 {
 	mmc-ddr-1_8v;
 	mmc-hs200-1_8v;
 	non-removable;
+	max-frequency = <75000000>;
 	vmmc-supply = <&reg_cldo3>;
 	vqmmc-supply = <&reg_cldo1>;
 	status = "okay";
Signature · 1 line
2.39.5
#1 lore raw

On Thu, 21 Aug 2025 21:29:35 +0800
Chen-Yu Tsai <[email protected]> wrote:

Hi Chen-Yu,

Quoted 21 lines

From: Chen-Yu Tsai <[email protected]>

The eMMC on the Orange Pi 4A doesn't function correctly at full speed of 150 MHz under HS200 mode. Either the traces on the board or module aren't great, or the SoC's internal delays are incorrect. Tuning the pin drive strength did not help.

After some experimenting, 75 MHz was found to be stable enough. Use this as the maximum frequency for now.

Fixes de713ccb9934 ("arm64: dts: allwinner: t527: Add OrangePi 4A board")
---
 arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts +0 -0
index c52d09cf0888..fb5311a46c2e 100644

arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts &mmc2 { · line 163

Quoted 4 lines
arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts +1 -0
@@ -160,6 +160,7 @@ &mmc2 {
 	mmc-ddr-1_8v;
 	mmc-hs200-1_8v;
 	non-removable;
+	max-frequency = <75000000>;

I am not a big fan of this change, as it looks like we are papering over something. I think the BSP runs it as a higher frequency just fine, can you check that? Traditionally the BSP uses HS400, IIRC, maybe we should finally bite the bullet and enable that?

Mikhail has some other assorted changes to beat his WalnutPi into submission, among others a slight increase of the voltage, both I/O (1.9V) and supply (3.4V). Also he increased the pins driving capability to 40mA, did you try that?

On my boards I tried to lower the frequency as well, but didn't get consistent results, though there was *some* improvement (at least probed the block device and read the partition table). And I needed to go much lower (40 MHz), so I wonder if this is all related to some bigger underlying issue.

Cheers,
Andre

Quoted 3 lines
arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts +0 -0
 	vmmc-supply = <&reg_cldo3>;
 	vqmmc-supply = <&reg_cldo1>;
 	status = "okay";