Skip to contentSkip to conversation

Bringup of SM7150 SoC

PATCH In review Jens Reidel 3 participants 11 messages Aug 31, 2025 – Sep 17, 2025

Subsystems (7)
lore
Share & tools
lore
#0 lore raw

cover Bringup of SM7150 SoC

This series adds a clock and pinctrl driver for the Qualcomm SM7150 SoC and enables support for the SoC in the UFS driver.

The other necessary bits are part of Luca's SM6350 series [1] or were sent separately.

All the drivers sent here are upstream in Linux already, however the devicetrees aren't yet, but that shouldn't be a blocker for including these drivers in U-Boot.

Tested on a couple of different Xiaomi devices, the Google Pixel 4a and the Samsung Galaxy A71.

[1]: https://lore.kernel.org/u-boot/[email protected]/

---
Danila Tikhonov (4):
clk/qcom: add driver for SM7150 GCC
pinctrl: qcom: add SM7150 pinctrl driver
phy: qcom-qmp-ufs: Import SM7150 tables from Linux
configs: qcom_defconfig: Enable SM7150 GCC and Pinctrl

 configs/qcom_defconfig                |   2 +
 drivers/clk/qcom/Kconfig              |   8 +
 drivers/clk/qcom/Makefile             |   1 +
 drivers/clk/qcom/clock-sm7150.c       | 250 ++++++++++++++++++++++++++
 drivers/phy/qcom/phy-qcom-qmp-ufs.c   |  61 +++++++
 drivers/pinctrl/qcom/Kconfig          |   7 +
 drivers/pinctrl/qcom/Makefile         |   1 +
 drivers/pinctrl/qcom/pinctrl-sm7150.c | 142 +++++++++++++++
 8 files changed, 472 insertions(+)
 create mode 100644 drivers/clk/qcom/clock-sm7150.c
 create mode 100644 drivers/pinctrl/qcom/pinctrl-sm7150.c
Signature · 1 line
2.51.0
#1 lore raw

PATCH 1/4 clk/qcom: add driver for SM7150 GCC

From: Danila Tikhonov <[email protected]>

Add a clock driver for the SM7150 SoC. This driver can enable necessary clocks for UART, UFS, USB, and MMC.

---
 drivers/clk/qcom/Kconfig        |   8 +
 drivers/clk/qcom/Makefile       |   1 +
 drivers/clk/qcom/clock-sm7150.c | 250 ++++++++++++++++++++++++++++++++
 3 files changed, 259 insertions(+)
 create mode 100644 drivers/clk/qcom/clock-sm7150.c
drivers/clk/qcom/Kconfig +8 -0
index 34e41461e72..ca913feb2af 100644
@@ -103,6 +103,14 @@ config CLK_QCOM_SM6115
 	  on the Snapdragon SM6115 SoC. This driver supports the clocks
 	  and resets exposed by the GCC hardware block.
 
+config CLK_QCOM_SM7150
+	bool "Qualcomm SM7150 GCC"
+	select CLK_QCOM
+	help
+	  Say Y here to enable support for the Global Clock Controller
+	  on the Snapdragon SM7150 SoC. This driver supports the clocks
+	  and resets exposed by the GCC hardware block.
+
 config CLK_QCOM_SM8150
 	bool "Qualcomm SM8150 GCC"
 	select CLK_QCOM
drivers/clk/qcom/Makefile +1 -0
index b3d95b0faa3..9e8ca2bd69e 100644
@@ -16,6 +16,7 @@ obj-$(CONFIG_CLK_QCOM_QCS615) += clock-qcs615.o
 obj-$(CONFIG_CLK_QCOM_SA8775P) += clock-sa8775p.o
 obj-$(CONFIG_CLK_QCOM_SC7280) += clock-sc7280.o
 obj-$(CONFIG_CLK_QCOM_SM6115) += clock-sm6115.o
+obj-$(CONFIG_CLK_QCOM_SM7150) += clock-sm7150.o
 obj-$(CONFIG_CLK_QCOM_SM8150) += clock-sm8150.o
 obj-$(CONFIG_CLK_QCOM_SM8250) += clock-sm8250.o
 obj-$(CONFIG_CLK_QCOM_SM8550) += clock-sm8550.o
drivers/clk/qcom/clock-sm7150.c new file +250 -0

250 lines not on this page · raw message

Signature · 1 line
2.51.0
Reviewed-by on v1 1/4
#2 lore raw

Re: [PATCH 1/4] clk/qcom: add driver for SM7150 GCC

Hi Jens,

Thanks! Since the dt-binding headers are already available for this platform this is all good.

Quoted 8 lines · Jens Reidel

From: Danila Tikhonov <[email protected]>

Add a clock driver for the SM7150 SoC. This driver can enable necessary clocks for UART, UFS, USB, and MMC.

Quoted 294 lines
---
 drivers/clk/qcom/Kconfig        |   8 +
 drivers/clk/qcom/Makefile       |   1 +
 drivers/clk/qcom/clock-sm7150.c | 250 ++++++++++++++++++++++++++++++++
 3 files changed, 259 insertions(+)
 create mode 100644 drivers/clk/qcom/clock-sm7150.c
drivers/clk/qcom/Kconfig +8 -0
index 34e41461e72..ca913feb2af 100644
@@ -103,6 +103,14 @@ config CLK_QCOM_SM6115
 	  on the Snapdragon SM6115 SoC. This driver supports the clocks
 	  and resets exposed by the GCC hardware block.
 
+config CLK_QCOM_SM7150
+	bool "Qualcomm SM7150 GCC"
+	select CLK_QCOM
+	help
+	  Say Y here to enable support for the Global Clock Controller
+	  on the Snapdragon SM7150 SoC. This driver supports the clocks
+	  and resets exposed by the GCC hardware block.
+
 config CLK_QCOM_SM8150
 	bool "Qualcomm SM8150 GCC"
 	select CLK_QCOM
drivers/clk/qcom/Makefile +1 -0
index b3d95b0faa3..9e8ca2bd69e 100644
@@ -16,6 +16,7 @@ obj-$(CONFIG_CLK_QCOM_QCS615) += clock-qcs615.o
 obj-$(CONFIG_CLK_QCOM_SA8775P) += clock-sa8775p.o
 obj-$(CONFIG_CLK_QCOM_SC7280) += clock-sc7280.o
 obj-$(CONFIG_CLK_QCOM_SM6115) += clock-sm6115.o
+obj-$(CONFIG_CLK_QCOM_SM7150) += clock-sm7150.o
 obj-$(CONFIG_CLK_QCOM_SM8150) += clock-sm8150.o
 obj-$(CONFIG_CLK_QCOM_SM8250) += clock-sm8250.o
 obj-$(CONFIG_CLK_QCOM_SM8550) += clock-sm8550.o
drivers/clk/qcom/clock-sm7150.c new file +250 -0
new file mode 100644
index 00000000000..8fe2076e55e
@@ -0,0 +1,250 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Clock drivers for Qualcomm SM7150
+ *
+ * (C) Copyright 2025 Danila Tikhonov <[email protected]>
+ * (C) Copyright 2025 Jens Reidel <[email protected]>
+ *
+ * Based on Linux Kernel driver
+ */
+
+#include <clk-uclass.h>
+#include <dm.h>
+#include <linux/delay.h>
+#include <asm/io.h>
+#include <linux/bug.h>
+#include <linux/bitops.h>
+#include <dt-bindings/clock/qcom,sm7150-gcc.h>
+
+#include "clock-qcom.h"
+
+#define USB30_PRIM_MASTER_CLK_CMD_RCGR		0xf01c
+#define USB30_PRIM_MOCK_UTMI_CLK_CMD_RCGR	0xf034
+#define USB3_PRIM_PHY_AUX_CLK_CMD_RCGR		0xf060
+
+#define SE8_UART_APPS_CMD_RCGR			0x18278
+#define GCC_SDCC2_APPS_CLK_SRC_REG		0x1400c
+
+#define APCS_GPLL7_STATUS			0x27000
+#define APCS_GPLLX_ENA_REG			0x52000
+
+static const struct freq_tbl ftbl_gcc_qupv3_wrap0_s0_clk_src[] = {
+	F(7372800, CFG_CLK_SRC_GPLL0_EVEN, 1, 384, 15625),
+	F(14745600, CFG_CLK_SRC_GPLL0_EVEN, 1, 768, 15625),
+	F(19200000, CFG_CLK_SRC_CXO, 1, 0, 0),
+	F(29491200, CFG_CLK_SRC_GPLL0_EVEN, 1, 1536, 15625),
+	F(32000000, CFG_CLK_SRC_GPLL0_EVEN, 1, 8, 75),
+	F(48000000, CFG_CLK_SRC_GPLL0_EVEN, 1, 4, 25),
+	F(64000000, CFG_CLK_SRC_GPLL0_EVEN, 1, 16, 75),
+	F(80000000, CFG_CLK_SRC_GPLL0_EVEN, 1, 4, 15),
+	F(96000000, CFG_CLK_SRC_GPLL0_EVEN, 1, 8, 25),
+	F(100000000, CFG_CLK_SRC_GPLL0_EVEN, 3, 0, 0),
+	F(102400000, CFG_CLK_SRC_GPLL0_EVEN, 1, 128, 375),
+	F(112000000, CFG_CLK_SRC_GPLL0_EVEN, 1, 28, 75),
+	F(117964800, CFG_CLK_SRC_GPLL0_EVEN, 1, 6144, 15625),
+	F(120000000, CFG_CLK_SRC_GPLL0_EVEN, 2.5, 0, 0),
+	F(128000000, CFG_CLK_SRC_GPLL0, 1, 16, 75),
+	{ }
+};
+
+static const struct freq_tbl ftbl_gcc_sdcc2_apps_clk_src[] = {
+	F(400000, CFG_CLK_SRC_CXO, 12, 1, 4),
+	F(9600000, CFG_CLK_SRC_CXO, 2, 0, 0),
+	F(19200000, CFG_CLK_SRC_CXO, 1, 0, 0),
+	F(25000000, CFG_CLK_SRC_GPLL0_EVEN, 12, 0, 0),
+	F(50000000, CFG_CLK_SRC_GPLL0_EVEN, 6, 0, 0),
+	F(100000000, CFG_CLK_SRC_GPLL0, 6, 0, 0),
+	F(208000000, CFG_CLK_SRC_GPLL7, 4, 0, 0),
+	{ }
+};
+
+static const struct freq_tbl ftbl_gcc_usb30_prim_master_clk_src[] = {
+	F(66666667, CFG_CLK_SRC_GPLL0, 4.5, 0, 0),
+	F(133333333, CFG_CLK_SRC_GPLL0_EVEN, 4.5, 0, 0),
+	F(200000000, CFG_CLK_SRC_GPLL0, 3, 0, 0),
+	F(240000000, CFG_CLK_SRC_GPLL0, 2.5, 0, 0),
+	{ }
+};
+
+static const struct freq_tbl ftbl_gcc_usb30_prim_mock_utmi_clk_src[] = {
+	F(19200000, CFG_CLK_SRC_CXO, 1, 0, 0),
+	F(20000000, CFG_CLK_SRC_GPLL0_EVEN, 15, 0, 0),
+	F(40000000, CFG_CLK_SRC_GPLL0_EVEN, 7.5, 0, 0),
+	F(60000000, CFG_CLK_SRC_GPLL0, 10, 0, 0),
+	{ }
+};
+
+static const struct freq_tbl ftbl_gcc_usb3_prim_phy_aux_clk_src[] = {
+	F(19200000, CFG_CLK_SRC_CXO, 1, 0, 0),
+	{ }
+};
+
+static ulong sm7150_clk_set_rate(struct clk *clk, ulong rate)
+{
+	struct msm_clk_priv *priv = dev_get_priv(clk->dev);
+	const struct freq_tbl *freq;
+
+	if (clk->id < priv->data->num_clks)
+		debug("%s: %s, requested rate=%ld\n", __func__, priv->data->clks[clk->id].name, rate);
+
+	switch (clk->id) {
+	case GCC_QUPV3_WRAP1_S2_CLK: /* UART8 */
+		freq = qcom_find_freq(ftbl_gcc_qupv3_wrap0_s0_clk_src, rate);
+		clk_rcg_set_rate_mnd(priv->base, SE8_UART_APPS_CMD_RCGR,
+				     freq->pre_div, freq->m, freq->n, freq->src, 16);
+		return freq->freq;
+	case GCC_USB30_PRIM_MASTER_CLK:
+		freq = qcom_find_freq(ftbl_gcc_usb30_prim_master_clk_src, rate);
+		clk_rcg_set_rate_mnd(priv->base, USB30_PRIM_MASTER_CLK_CMD_RCGR,
+				     freq->pre_div, freq->m, freq->n, freq->src, 8);
+		return freq->freq;
+	case GCC_USB30_PRIM_MOCK_UTMI_CLK:
+		freq = qcom_find_freq(ftbl_gcc_usb30_prim_mock_utmi_clk_src, rate);
+		clk_rcg_set_rate_mnd(priv->base, USB30_PRIM_MOCK_UTMI_CLK_CMD_RCGR,
+				     freq->pre_div, freq->m, freq->n, freq->src, 0);
+		return freq->freq;
+	case GCC_USB3_PRIM_PHY_AUX_CLK_SRC:
+		freq = qcom_find_freq(ftbl_gcc_usb3_prim_phy_aux_clk_src, rate);
+		clk_rcg_set_rate_mnd(priv->base, USB3_PRIM_PHY_AUX_CLK_CMD_RCGR,
+				     freq->pre_div, freq->m, freq->n, freq->src, 0);
+		return freq->freq;
+	case GCC_SDCC2_APPS_CLK:
+		freq = qcom_find_freq(ftbl_gcc_sdcc2_apps_clk_src, rate);
+		clk_rcg_set_rate_mnd(priv->base, GCC_SDCC2_APPS_CLK_SRC_REG,
+				     freq->pre_div, freq->m, freq->n, freq->src, 8);
+		return freq->freq;
+	default:
+		return 0;
+	}
+}
+
+static const struct gate_clk sm7150_clks[] = {
+	GATE_CLK(GCC_AGGRE_UFS_PHY_AXI_CLK,	0x82024, BIT(0)),
+	GATE_CLK(GCC_AGGRE_USB3_PRIM_AXI_CLK,	0x8201c, BIT(0)),
+	GATE_CLK(GCC_CFG_NOC_USB3_PRIM_AXI_CLK,	0x502c,  BIT(0)),
+	GATE_CLK(GCC_QUPV3_WRAP0_S0_CLK,	0x5200c, BIT(10)),
+	GATE_CLK(GCC_QUPV3_WRAP0_S1_CLK,	0x5200c, BIT(11)),
+	GATE_CLK(GCC_QUPV3_WRAP0_S2_CLK,	0x5200c, BIT(12)),
+	GATE_CLK(GCC_QUPV3_WRAP0_S3_CLK,	0x5200c, BIT(13)),
+	GATE_CLK(GCC_QUPV3_WRAP0_S4_CLK,	0x5200c, BIT(14)),
+	GATE_CLK(GCC_QUPV3_WRAP0_S5_CLK,	0x5200c, BIT(15)),
+	GATE_CLK(GCC_QUPV3_WRAP0_S6_CLK,	0x5200c, BIT(16)),
+	GATE_CLK(GCC_QUPV3_WRAP0_S7_CLK,	0x5200c, BIT(17)),
+	GATE_CLK(GCC_QUPV3_WRAP1_S0_CLK,	0x5200c, BIT(22)),
+	GATE_CLK(GCC_QUPV3_WRAP1_S1_CLK,	0x5200c, BIT(23)),
+	GATE_CLK(GCC_QUPV3_WRAP1_S2_CLK,	0x5200c, BIT(24)),
+	GATE_CLK(GCC_QUPV3_WRAP1_S3_CLK,	0x5200c, BIT(25)),
+	GATE_CLK(GCC_QUPV3_WRAP1_S4_CLK,	0x5200c, BIT(26)),
+	GATE_CLK(GCC_QUPV3_WRAP1_S5_CLK,	0x5200c, BIT(27)),
+	GATE_CLK(GCC_QUPV3_WRAP1_S6_CLK,	0x5200c, BIT(28)),
+	GATE_CLK(GCC_QUPV3_WRAP1_S7_CLK,	0x5200c, BIT(29)),
+	GATE_CLK(GCC_QUPV3_WRAP_0_M_AHB_CLK,	0x5200c, BIT(6)),
+	GATE_CLK(GCC_QUPV3_WRAP_0_S_AHB_CLK,	0x5200c, BIT(7)),
+	GATE_CLK(GCC_QUPV3_WRAP_1_M_AHB_CLK,	0x5200c, BIT(20)),
+	GATE_CLK(GCC_QUPV3_WRAP_1_S_AHB_CLK,	0x5200c, BIT(21)),
+	GATE_CLK(GCC_SDCC1_AHB_CLK,		0x12008, BIT(0)),
+	GATE_CLK(GCC_SDCC1_APPS_CLK,		0x1200c, BIT(0)),
+	GATE_CLK(GCC_SDCC1_ICE_CORE_CLK,	0x12040, BIT(0)),
+	GATE_CLK(GCC_SDCC2_AHB_CLK,		0x14008, BIT(0)),
+	GATE_CLK(GCC_SDCC2_APPS_CLK,		0x14004, BIT(0)),
+	GATE_CLK(GCC_SDCC4_AHB_CLK,		0x16008, BIT(0)),
+	GATE_CLK(GCC_SDCC4_APPS_CLK,		0x16004, BIT(0)),
+	GATE_CLK(GCC_UFS_MEM_CLKREF_CLK,	0x8c000, BIT(0)),
+	GATE_CLK(GCC_UFS_PHY_AHB_CLK,		0x77014, BIT(0)),
+	GATE_CLK(GCC_UFS_PHY_AXI_CLK,		0x77038, BIT(0)),
+	GATE_CLK(GCC_UFS_PHY_ICE_CORE_CLK,	0x77090, BIT(0)),
+	GATE_CLK(GCC_UFS_PHY_PHY_AUX_CLK,	0x77094, BIT(0)),
+	GATE_CLK(GCC_UFS_PHY_RX_SYMBOL_0_CLK,	0x7701c, BIT(0)),
+	GATE_CLK(GCC_UFS_PHY_TX_SYMBOL_0_CLK,	0x77018, BIT(0)),
+	GATE_CLK(GCC_UFS_PHY_UNIPRO_CORE_CLK,	0x7708c, BIT(0)),
+	GATE_CLK(GCC_USB30_PRIM_MASTER_CLK,	0x0f010, BIT(0)),
+	GATE_CLK(GCC_USB30_PRIM_MOCK_UTMI_CLK,	0x0f018, BIT(0)),
+	GATE_CLK(GCC_USB30_PRIM_SLEEP_CLK,	0x0f014, BIT(0)),
+	GATE_CLK(GCC_USB3_PRIM_CLKREF_CLK,	0x8c010, BIT(0)),
+	GATE_CLK(GCC_USB3_PRIM_PHY_AUX_CLK,	0x0f050, BIT(0)),
+	GATE_CLK(GCC_USB3_PRIM_PHY_COM_AUX_CLK,	0x0f054, BIT(0)),
+	GATE_CLK(GCC_USB3_PRIM_PHY_PIPE_CLK,	0x0f058, BIT(0)),
+	GATE_CLK(GCC_USB_PHY_CFG_AHB2PHY_CLK,	0x6a004, BIT(0)),
+};
+
+static int sm7150_clk_enable(struct clk *clk)
+{
+	struct msm_clk_priv *priv = dev_get_priv(clk->dev);
+
+	if (priv->data->num_clks < clk->id) {
+		debug("%s: unknown clk id %lu\n", __func__, clk->id);
+		return 0;
+	}
+
+	debug("%s: clk %s\n", __func__, sm7150_clks[clk->id].name);
+
+	switch (clk->id) {
+	case GCC_AGGRE_USB3_PRIM_AXI_CLK:
+		qcom_gate_clk_en(priv, GCC_USB30_PRIM_MASTER_CLK);
+		fallthrough;
+	case GCC_USB30_PRIM_MASTER_CLK:
+		qcom_gate_clk_en(priv, GCC_USB3_PRIM_PHY_AUX_CLK);
+		qcom_gate_clk_en(priv, GCC_USB3_PRIM_PHY_COM_AUX_CLK);
+		break;
+	}
+
+	return qcom_gate_clk_en(priv, clk->id);
+}
+
+static const struct qcom_reset_map sm7150_gcc_resets[] = {
+	[GCC_UFS_PHY_BCR] = { 0x77000 },
+	[GCC_USB30_PRIM_BCR] = { 0xf000 },
+	[GCC_USB3_DP_PHY_PRIM_BCR] = { 0x50008 },
+	[GCC_USB3_DP_PHY_SEC_BCR] = { 0x50014 },
+	[GCC_USB3_PHY_PRIM_BCR] = { 0x50000 },
+	[GCC_USB3_PHY_SEC_BCR] = { 0x5000c },
+	[GCC_QUSB2PHY_PRIM_BCR] = { 0x26000 },
+};
+
+static const struct qcom_power_map sm7150_gdscs[] = {
+	[PCIE_0_GDSC] = { 0x6b004 },
+	[UFS_PHY_GDSC] = { 0x77004 },
+	[USB30_PRIM_GDSC] = { 0xf004 },
+};
+
+static const phys_addr_t sm7150_rcg_addrs[] = {
+	0x10f01c, // USB30_PRIM_MASTER_CLK_CMD_RCGR
+	0x10f034, // USB30_PRIM_MOCK_UTMI_CLK_CMD_RCGR
+	0x10f060, // USB3_PRIM_PHY_AUX_CLK_CMD_RCGR,
+};
+
+static const char *const sm7150_rcg_names[] = {
+	"USB30_PRIM_MASTER_CLK",
+	"USB30_PRIM_MOCK_UTMI_CLK",
+	"USB3_PRIM_PHY_AUX_CLK",
+};
+
+static struct msm_clk_data sm7150_gcc_data = {
+	.resets = sm7150_gcc_resets,
+	.num_resets = ARRAY_SIZE(sm7150_gcc_resets),
+	.clks = sm7150_clks,
+	.num_clks = ARRAY_SIZE(sm7150_clks),
+
+	.power_domains = sm7150_gdscs,
+	.num_power_domains = ARRAY_SIZE(sm7150_gdscs),
+
+	.enable = sm7150_clk_enable,
+	.set_rate = sm7150_clk_set_rate,
+
+	.dbg_rcg_addrs = sm7150_rcg_addrs,
+	.num_rcgs = ARRAY_SIZE(sm7150_rcg_addrs),
+	.dbg_rcg_names = sm7150_rcg_names,
+};
+
+static const struct udevice_id gcc_sm7150_of_match[] = {
+	{ .compatible = "qcom,sm7150-gcc", .data = (ulong)&sm7150_gcc_data, },
+	{ /* sentinel */ }
+};
+
+U_BOOT_DRIVER(gcc_sm7150) = {
+	.name		= "gcc_sm7150",
+	.id		= UCLASS_NOP,
+	.of_match	= gcc_sm7150_of_match,
+	.bind		= qcom_cc_bind,
+	.flags		= DM_FLAG_PRE_RELOC | DM_FLAG_DEFAULT_PD_CTRL_OFF,
+};
Signature · 1 line
// Casey (she/her)
#3 lore raw

PATCH 2/4 pinctrl: qcom: add SM7150 pinctrl driver

In reply to Jens Reidel

From: Danila Tikhonov <[email protected]>

This SoC features a pinctrl block with north, south, and west tiles accessible to the AP.

---
 drivers/pinctrl/qcom/Kconfig          |   7 ++
 drivers/pinctrl/qcom/Makefile         |   1 +
 drivers/pinctrl/qcom/pinctrl-sm7150.c | 142 ++++++++++++++++++++++++++
 3 files changed, 150 insertions(+)
 create mode 100644 drivers/pinctrl/qcom/pinctrl-sm7150.c
drivers/pinctrl/qcom/Kconfig +7 -0
index 21f81b66099..d83ede21c75 100644
@@ -89,6 +89,13 @@ config PINCTRL_QCOM_SM6115
 	  Say Y here to enable support for pinctrl on the Snapdragon SM6115 SoC,
 	  as well as the associated GPIO driver.
 
+config PINCTRL_QCOM_SM7150
+	bool "Qualcomm SM7150 GCC"
+	select PINCTRL_QCOM
+	help
+	  Say Y here to enable support for pinctrl on the Snapdragon SM7150 SoC,
+	  as well as the associated GPIO driver.
+
 config PINCTRL_QCOM_SM8150
 	bool "Qualcomm SM8150 Pinctrl"
 	select PINCTRL_QCOM
drivers/pinctrl/qcom/Makefile +1 -0
index 6cb53838e71..73c08a02a3d 100644
@@ -15,6 +15,7 @@ obj-$(CONFIG_PINCTRL_QCOM_SC7280) += pinctrl-sc7280.o
 obj-$(CONFIG_PINCTRL_QCOM_SDM660) += pinctrl-sdm660.o
 obj-$(CONFIG_PINCTRL_QCOM_SDM845) += pinctrl-sdm845.o
 obj-$(CONFIG_PINCTRL_QCOM_SM6115) += pinctrl-sm6115.o
+obj-$(CONFIG_PINCTRL_QCOM_SM7150) += pinctrl-sm7150.o
 obj-$(CONFIG_PINCTRL_QCOM_SM8150) += pinctrl-sm8150.o
 obj-$(CONFIG_PINCTRL_QCOM_SM8250) += pinctrl-sm8250.o
 obj-$(CONFIG_PINCTRL_QCOM_SM8550) += pinctrl-sm8550.o
drivers/pinctrl/qcom/pinctrl-sm7150.c new file +142 -0

142 lines not on this page · raw message

Signature · 1 line
2.51.0
#4 lore raw

Re: [PATCH 2/4] pinctrl: qcom: add SM7150 pinctrl driver

Quoted 145 lines · Jens Reidel

From: Danila Tikhonov <[email protected]>

This SoC features a pinctrl block with north, south, and west tiles accessible to the AP.

---
 drivers/pinctrl/qcom/Kconfig          |   7 ++
 drivers/pinctrl/qcom/Makefile         |   1 +
 drivers/pinctrl/qcom/pinctrl-sm7150.c | 142 ++++++++++++++++++++++++++
 3 files changed, 150 insertions(+)
 create mode 100644 drivers/pinctrl/qcom/pinctrl-sm7150.c
drivers/pinctrl/qcom/Kconfig +7 -0
index 21f81b66099..d83ede21c75 100644
@@ -89,6 +89,13 @@ config PINCTRL_QCOM_SM6115
 	  Say Y here to enable support for pinctrl on the Snapdragon SM6115 SoC,
 	  as well as the associated GPIO driver.
 
+config PINCTRL_QCOM_SM7150
+	bool "Qualcomm SM7150 GCC"
+	select PINCTRL_QCOM
+	help
+	  Say Y here to enable support for pinctrl on the Snapdragon SM7150 SoC,
+	  as well as the associated GPIO driver.
+
 config PINCTRL_QCOM_SM8150
 	bool "Qualcomm SM8150 Pinctrl"
 	select PINCTRL_QCOM
drivers/pinctrl/qcom/Makefile +1 -0
index 6cb53838e71..73c08a02a3d 100644
@@ -15,6 +15,7 @@ obj-$(CONFIG_PINCTRL_QCOM_SC7280) += pinctrl-sc7280.o
 obj-$(CONFIG_PINCTRL_QCOM_SDM660) += pinctrl-sdm660.o
 obj-$(CONFIG_PINCTRL_QCOM_SDM845) += pinctrl-sdm845.o
 obj-$(CONFIG_PINCTRL_QCOM_SM6115) += pinctrl-sm6115.o
+obj-$(CONFIG_PINCTRL_QCOM_SM7150) += pinctrl-sm7150.o
 obj-$(CONFIG_PINCTRL_QCOM_SM8150) += pinctrl-sm8150.o
 obj-$(CONFIG_PINCTRL_QCOM_SM8250) += pinctrl-sm8250.o
 obj-$(CONFIG_PINCTRL_QCOM_SM8550) += pinctrl-sm8550.o
drivers/pinctrl/qcom/pinctrl-sm7150.c new file +94 -0
new file mode 100644
index 00000000000..435ba39b1db
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Pinctrl driver for Qualcomm SM7150
+ *
+ * (C) Copyright 2025 Danila Tikhonov <[email protected]>
+ * (C) Copyright 2025 Jens Reidel <[email protected]>
+ *
+ * Based on Linux Kernel driver
+ */
+
+#include <dm.h>
+
+#include "pinctrl-qcom.h"
+
+#define WEST	0x00000000
+#define NORTH	0x00400000
+#define SOUTH	0x00800000
+
+#define MAX_PIN_NAME_LEN 32
+static char pin_name[MAX_PIN_NAME_LEN] __section(".data");
+
+static const struct pinctrl_function msm_pinctrl_functions[] = {
+	{ "qup12", 1 },
+	{ "gpio",  0 },
+	{ "sdc2_clk", 0 } /* special pin GPIO124 */
+};
+
+#define SDC_QDSD_PINGROUP(pg_name, ctl, pull, drv)	\
+	{						\
+		.name = pg_name,			\
+		.ctl_reg = ctl,				\
+		.io_reg = 0,				\
+		.pull_bit = pull,			\
+		.drv_bit = drv,				\
+		.oe_bit = -1,				\
+		.in_bit = -1,				\
+		.out_bit = -1,				\
+	}
+
+#define UFS_RESET(pg_name, offset)			\
+	{						\
+		.name = pg_name,			\
+		.ctl_reg = offset,			\
+		.io_reg = offset + 0x4,			\
+		.pull_bit = 3,				\
+		.drv_bit = 0,				\
+		.oe_bit = -1,				\
+		.in_bit = -1,				\
+		.out_bit = 0,				\
+	}
+
+static const struct msm_special_pin_data msm_special_pins_data[] = {
+	[0] = UFS_RESET("ufs_reset", 0x9f000),
+	[1] = SDC_QDSD_PINGROUP("sdc1_rclk", WEST + 0x9a000, 15, 0),
+	[2] = SDC_QDSD_PINGROUP("sdc1_clk", WEST + 0x9a000, 13, 6),
+	[3] = SDC_QDSD_PINGROUP("sdc1_cmd", WEST + 0x9a000, 11, 3),
+	[4] = SDC_QDSD_PINGROUP("sdc1_data", WEST + 0x9a000, 9, 0),
+	[5] = SDC_QDSD_PINGROUP("sdc2_clk", SOUTH + 0x98000, 14, 6),
+	[6] = SDC_QDSD_PINGROUP("sdc2_cmd", SOUTH + 0x98000, 11, 3),
+	[7] = SDC_QDSD_PINGROUP("sdc2_data", SOUTH + 0x98000, 9, 0),
+};
+
+static const unsigned int sm7150_pin_offsets[] = {
+	[0] = SOUTH,	[1] = SOUTH,	[2] = SOUTH,	[3] = SOUTH,
+	[4] = NORTH,	[5] = NORTH,	[6] = NORTH,	[7] = NORTH,
+	[8] = NORTH,	[9] = NORTH,	[10] = NORTH,	[11] = NORTH,
+	[12] = SOUTH,	[13] = SOUTH,	[14] = SOUTH,	[15] = SOUTH,
+	[16] = SOUTH,	[17] = SOUTH,	[18] = SOUTH,	[19] = SOUTH,
+	[20] = SOUTH,	[21] = SOUTH,	[22] = SOUTH,	[23] = SOUTH,
+	[24] = SOUTH,	[25] = SOUTH,	[26] = SOUTH,	[27] = SOUTH,
+	[28] = SOUTH,	[29] = NORTH,	[30] = SOUTH,	[31] = WEST,
+	[32] = NORTH,	[33] = NORTH,	[34] = SOUTH,	[35] = SOUTH,
+	[36] = SOUTH,	[37] = SOUTH,	[38] = SOUTH,	[39] = SOUTH,
+	[40] = SOUTH,	[41] = SOUTH,	[42] = NORTH,	[43] = NORTH,
+	[44] = NORTH,	[45] = NORTH,	[46] = NORTH,	[47] = NORTH,
+	[48] = WEST,	[49] = WEST,	[50] = WEST,	[51] = WEST,
+	[52] = WEST,	[53] = WEST,	[54] = WEST,	[55] = WEST,
+	[56] = WEST,	[57] = WEST,	[58] = WEST,	[59] = NORTH,
+	[60] = NORTH,	[61] = NORTH,	[62] = NORTH,	[63] = NORTH,
+	[64] = NORTH,	[65] = NORTH,	[66] = NORTH,	[67] = NORTH,
+	[68] = NORTH,	[69] = NORTH,	[70] = NORTH,	[71] = NORTH,
+	[72] = NORTH,	[73] = NORTH,	[74] = WEST,	[75] = WEST,
+	[76] = WEST,	[77] = WEST,	[78] = WEST,	[79] = WEST,
+	[80] = WEST,	[81] = WEST,	[82] = WEST,	[83] = WEST,
+	[84] = WEST,	[85] = WEST,	[86] = NORTH,	[87] = NORTH,
+	[88] = NORTH,	[89] = NORTH,	[90] = NORTH,	[91] = NORTH,
+	[92] = NORTH,	[93] = NORTH,	[94] = SOUTH,	[95] = WEST,
+	[96] = WEST,	[97] = WEST,	[98] = WEST,	[99] = WEST,
+	[100] = WEST,	[101] = NORTH,	[102] = NORTH,	[103] = NORTH,
+	[104] = WEST,	[105] = NORTH,	[106] = NORTH,	[107] = WEST,
+	[108] = SOUTH,	[109] = SOUTH,	[110] = NORTH,	[111] = NORTH,
+	[112] = NORTH,	[113] = NORTH,	[114] = NORTH,	[115] = NORTH,
+	[116] = NORTH,	[117] = NORTH,	[118] = NORTH,
+};

drivers/pinctrl/qcom/pinctrl-sm7150.c line 104

Quoted 10 lines
drivers/pinctrl/qcom/pinctrl-sm7150.c new file +10 -0
+
+static const char *sm7150_get_function_name(struct udevice *dev, unsigned int selector)
+{
+	return msm_pinctrl_functions[selector].name;
+}
+
+static const char *sm7150_get_pin_name(struct udevice *dev,
+				       unsigned int selector)
+{
+	if (selector >= 119 && selector <= 126)

This should be && select <= 127, since there are 8 special pins. We should really update all the drivers to use ARRAY_LENGTH macros rather than doing all the maths by hand since so many have had errors at this point ahaha

Kind regards,> + snprintf(pin_name, MAX_PIN_NAME_LEN,

Quoted 37 lines
drivers/pinctrl/qcom/pinctrl-sm7150.c new file +37 -0
+			 msm_special_pins_data[selector - 119].name);
+	else
+		snprintf(pin_name, MAX_PIN_NAME_LEN, "gpio%u", selector);
+
+	return pin_name;
+}
+
+static int sm7150_get_function_mux(__maybe_unused unsigned int pin, unsigned int selector)
+{
+	return msm_pinctrl_functions[selector].val;
+}
+
+static struct msm_pinctrl_data sm7150_data = {
+	.pin_data = {
+		.pin_offsets = sm7150_pin_offsets,
+		.pin_count = 126,
+		.special_pins_start = 119,
+		.special_pins_data = msm_special_pins_data,
+	},
+	.functions_count = ARRAY_SIZE(msm_pinctrl_functions),
+	.get_function_name = sm7150_get_function_name,
+	.get_function_mux = sm7150_get_function_mux,
+	.get_pin_name = sm7150_get_pin_name,
+};
+
+static const struct udevice_id msm_pinctrl_ids[] = {
+	{ .compatible = "qcom,sm7150-tlmm", .data = (ulong)&sm7150_data },
+	{ /* sentinel */ }
+};
+
+U_BOOT_DRIVER(pinctrl_sm7150) = {
+	.name		= "pinctrl_sm7150",
+	.id		= UCLASS_NOP,
+	.of_match	= msm_pinctrl_ids,
+	.ops		= &msm_pinctrl_ops,
+	.bind		= msm_pinctrl_bind,
+};
Signature · 1 line
// Casey (she/her)
#5 lore raw

Re: [PATCH 2/4] pinctrl: qcom: add SM7150 pinctrl driver

Quoted 164 lines · Casey Connolly
Quoted 145 lines · Jens Reidel

From: Danila Tikhonov <[email protected]>

This SoC features a pinctrl block with north, south, and west tiles accessible to the AP.

---
  drivers/pinctrl/qcom/Kconfig          |   7 ++
  drivers/pinctrl/qcom/Makefile         |   1 +
  drivers/pinctrl/qcom/pinctrl-sm7150.c | 142 ++++++++++++++++++++++++++
  3 files changed, 150 insertions(+)

create mode 100644 drivers/pinctrl/qcom/pinctrl-sm7150.c

drivers/pinctrl/qcom/Kconfig +7 -0
index 21f81b66099..d83ede21c75 100644
@@ -89,6 +89,13 @@ config PINCTRL_QCOM_SM6115
  	  Say Y here to enable support for pinctrl on the Snapdragon SM6115 SoC,
  	  as well as the associated GPIO driver.
 
+config PINCTRL_QCOM_SM7150
+	bool "Qualcomm SM7150 GCC"
+	select PINCTRL_QCOM
+	help
+	  Say Y here to enable support for pinctrl on the Snapdragon SM7150 SoC,
+	  as well as the associated GPIO driver.
+
  config PINCTRL_QCOM_SM8150
  	bool "Qualcomm SM8150 Pinctrl"
  	select PINCTRL_QCOM
drivers/pinctrl/qcom/Makefile +1 -0
index 6cb53838e71..73c08a02a3d 100644
@@ -15,6 +15,7 @@ obj-$(CONFIG_PINCTRL_QCOM_SC7280) += pinctrl-sc7280.o
  obj-$(CONFIG_PINCTRL_QCOM_SDM660) += pinctrl-sdm660.o
  obj-$(CONFIG_PINCTRL_QCOM_SDM845) += pinctrl-sdm845.o
  obj-$(CONFIG_PINCTRL_QCOM_SM6115) += pinctrl-sm6115.o
+obj-$(CONFIG_PINCTRL_QCOM_SM7150) += pinctrl-sm7150.o
  obj-$(CONFIG_PINCTRL_QCOM_SM8150) += pinctrl-sm8150.o
  obj-$(CONFIG_PINCTRL_QCOM_SM8250) += pinctrl-sm8250.o
  obj-$(CONFIG_PINCTRL_QCOM_SM8550) += pinctrl-sm8550.o
drivers/pinctrl/qcom/pinctrl-sm7150.c new file +94 -0
new file mode 100644
index 00000000000..435ba39b1db
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Pinctrl driver for Qualcomm SM7150
+ *
+ * (C) Copyright 2025 Danila Tikhonov <[email protected]>
+ * (C) Copyright 2025 Jens Reidel <[email protected]>
+ *
+ * Based on Linux Kernel driver
+ */
+
+#include <dm.h>
+
+#include "pinctrl-qcom.h"
+
+#define WEST	0x00000000
+#define NORTH	0x00400000
+#define SOUTH	0x00800000
+
+#define MAX_PIN_NAME_LEN 32
+static char pin_name[MAX_PIN_NAME_LEN] __section(".data");
+
+static const struct pinctrl_function msm_pinctrl_functions[] = {
+	{ "qup12", 1 },
+	{ "gpio",  0 },
+	{ "sdc2_clk", 0 } /* special pin GPIO124 */
+};
+
+#define SDC_QDSD_PINGROUP(pg_name, ctl, pull, drv)	\
+	{						\
+		.name = pg_name,			\
+		.ctl_reg = ctl,				\
+		.io_reg = 0,				\
+		.pull_bit = pull,			\
+		.drv_bit = drv,				\
+		.oe_bit = -1,				\
+		.in_bit = -1,				\
+		.out_bit = -1,				\
+	}
+
+#define UFS_RESET(pg_name, offset)			\
+	{						\
+		.name = pg_name,			\
+		.ctl_reg = offset,			\
+		.io_reg = offset + 0x4,			\
+		.pull_bit = 3,				\
+		.drv_bit = 0,				\
+		.oe_bit = -1,				\
+		.in_bit = -1,				\
+		.out_bit = 0,				\
+	}
+
+static const struct msm_special_pin_data msm_special_pins_data[] = {
+	[0] = UFS_RESET("ufs_reset", 0x9f000),
+	[1] = SDC_QDSD_PINGROUP("sdc1_rclk", WEST + 0x9a000, 15, 0),
+	[2] = SDC_QDSD_PINGROUP("sdc1_clk", WEST + 0x9a000, 13, 6),
+	[3] = SDC_QDSD_PINGROUP("sdc1_cmd", WEST + 0x9a000, 11, 3),
+	[4] = SDC_QDSD_PINGROUP("sdc1_data", WEST + 0x9a000, 9, 0),
+	[5] = SDC_QDSD_PINGROUP("sdc2_clk", SOUTH + 0x98000, 14, 6),
+	[6] = SDC_QDSD_PINGROUP("sdc2_cmd", SOUTH + 0x98000, 11, 3),
+	[7] = SDC_QDSD_PINGROUP("sdc2_data", SOUTH + 0x98000, 9, 0),
+};
+
+static const unsigned int sm7150_pin_offsets[] = {
+	[0] = SOUTH,	[1] = SOUTH,	[2] = SOUTH,	[3] = SOUTH,
+	[4] = NORTH,	[5] = NORTH,	[6] = NORTH,	[7] = NORTH,
+	[8] = NORTH,	[9] = NORTH,	[10] = NORTH,	[11] = NORTH,
+	[12] = SOUTH,	[13] = SOUTH,	[14] = SOUTH,	[15] = SOUTH,
+	[16] = SOUTH,	[17] = SOUTH,	[18] = SOUTH,	[19] = SOUTH,
+	[20] = SOUTH,	[21] = SOUTH,	[22] = SOUTH,	[23] = SOUTH,
+	[24] = SOUTH,	[25] = SOUTH,	[26] = SOUTH,	[27] = SOUTH,
+	[28] = SOUTH,	[29] = NORTH,	[30] = SOUTH,	[31] = WEST,
+	[32] = NORTH,	[33] = NORTH,	[34] = SOUTH,	[35] = SOUTH,
+	[36] = SOUTH,	[37] = SOUTH,	[38] = SOUTH,	[39] = SOUTH,
+	[40] = SOUTH,	[41] = SOUTH,	[42] = NORTH,	[43] = NORTH,
+	[44] = NORTH,	[45] = NORTH,	[46] = NORTH,	[47] = NORTH,
+	[48] = WEST,	[49] = WEST,	[50] = WEST,	[51] = WEST,
+	[52] = WEST,	[53] = WEST,	[54] = WEST,	[55] = WEST,
+	[56] = WEST,	[57] = WEST,	[58] = WEST,	[59] = NORTH,
+	[60] = NORTH,	[61] = NORTH,	[62] = NORTH,	[63] = NORTH,
+	[64] = NORTH,	[65] = NORTH,	[66] = NORTH,	[67] = NORTH,
+	[68] = NORTH,	[69] = NORTH,	[70] = NORTH,	[71] = NORTH,
+	[72] = NORTH,	[73] = NORTH,	[74] = WEST,	[75] = WEST,
+	[76] = WEST,	[77] = WEST,	[78] = WEST,	[79] = WEST,
+	[80] = WEST,	[81] = WEST,	[82] = WEST,	[83] = WEST,
+	[84] = WEST,	[85] = WEST,	[86] = NORTH,	[87] = NORTH,
+	[88] = NORTH,	[89] = NORTH,	[90] = NORTH,	[91] = NORTH,
+	[92] = NORTH,	[93] = NORTH,	[94] = SOUTH,	[95] = WEST,
+	[96] = WEST,	[97] = WEST,	[98] = WEST,	[99] = WEST,
+	[100] = WEST,	[101] = NORTH,	[102] = NORTH,	[103] = NORTH,
+	[104] = WEST,	[105] = NORTH,	[106] = NORTH,	[107] = WEST,
+	[108] = SOUTH,	[109] = SOUTH,	[110] = NORTH,	[111] = NORTH,
+	[112] = NORTH,	[113] = NORTH,	[114] = NORTH,	[115] = NORTH,
+	[116] = NORTH,	[117] = NORTH,	[118] = NORTH,
+};

drivers/pinctrl/qcom/pinctrl-sm7150.c line 104

Quoted 10 lines
drivers/pinctrl/qcom/pinctrl-sm7150.c new file +10 -0
+
+static const char *sm7150_get_function_name(struct udevice *dev, unsigned int selector)
+{
+	return msm_pinctrl_functions[selector].name;
+}
+
+static const char *sm7150_get_pin_name(struct udevice *dev,
+				       unsigned int selector)
+{
+	if (selector >= 119 && selector <= 126)

This should be && select <= 127, since there are 8 special pins. We should really update all the drivers to use ARRAY_LENGTH macros rather than doing all the maths by hand since so many have had errors at this point ahaha

Quoted 1 line

Kind regards,

Are you sure? I think this is correct, since start and end of the range are inclusive, so 119-126 are 8 GPIOs in total. The total pin count is also 126.

Best regards,
Jens

Quoted 39 lines
Quoted 38 lines
drivers/pinctrl/qcom/pinctrl-sm7150.c new file +38 -0
+		snprintf(pin_name, MAX_PIN_NAME_LEN,
+			 msm_special_pins_data[selector - 119].name);
+	else
+		snprintf(pin_name, MAX_PIN_NAME_LEN, "gpio%u", selector);
+
+	return pin_name;
+}
+
+static int sm7150_get_function_mux(__maybe_unused unsigned int pin, unsigned int selector)
+{
+	return msm_pinctrl_functions[selector].val;
+}
+
+static struct msm_pinctrl_data sm7150_data = {
+	.pin_data = {
+		.pin_offsets = sm7150_pin_offsets,
+		.pin_count = 126,
+		.special_pins_start = 119,
+		.special_pins_data = msm_special_pins_data,
+	},
+	.functions_count = ARRAY_SIZE(msm_pinctrl_functions),
+	.get_function_name = sm7150_get_function_name,
+	.get_function_mux = sm7150_get_function_mux,
+	.get_pin_name = sm7150_get_pin_name,
+};
+
+static const struct udevice_id msm_pinctrl_ids[] = {
+	{ .compatible = "qcom,sm7150-tlmm", .data = (ulong)&sm7150_data },
+	{ /* sentinel */ }
+};
+
+U_BOOT_DRIVER(pinctrl_sm7150) = {
+	.name		= "pinctrl_sm7150",
+	.id		= UCLASS_NOP,
+	.of_match	= msm_pinctrl_ids,
+	.ops		= &msm_pinctrl_ops,
+	.bind		= msm_pinctrl_bind,
+};
#6 lore raw

Re: [PATCH 2/4] pinctrl: qcom: add SM7150 pinctrl driver

Quoted 171 lines · Jens Reidel
Quoted 170 lines · Casey Connolly
Quoted 153 lines · Jens Reidel

From: Danila Tikhonov <[email protected]>

This SoC features a pinctrl block with north, south, and west tiles accessible to the AP.

---
  drivers/pinctrl/qcom/Kconfig          |   7 ++ drivers/pinctrl/qcom/Makefile         |   1 + drivers/pinctrl/qcom/pinctrl-sm7150.c | 142 ++++++++++++++++++++++++++

  3 files changed, 150 insertions(+)

  create mode 100644 drivers/pinctrl/qcom/pinctrl-sm7150.c

drivers/pinctrl/qcom/Kconfig +0 -0
index 21f81b66099..d83ede21c75 100644
@@ -89,6 +89,13 @@ config PINCTRL_QCOM_SM6115

        Say Y here to enable support for pinctrl on the Snapdragon SM6115 SoC,
        as well as the associated GPIO driver.
  +config PINCTRL_QCOM_SM7150
+    bool "Qualcomm SM7150 GCC"
+    select PINCTRL_QCOM
+    help
+      Say Y here to enable support for pinctrl on the Snapdragon SM7150 SoC,
+      as well as the associated GPIO driver.
+
  config PINCTRL_QCOM_SM8150
      bool "Qualcomm SM8150 Pinctrl"
      select PINCTRL_QCOM

drivers/pinctrl/qcom/ renamed from drivers/pinctrl/qcom/Makefile +0 -0

Makefile
index 6cb53838e71..73c08a02a3d 100644

drivers/pinctrl/qcom/Makefile +0 -0
@@ -15,6 +15,7 @@ obj-$(CONFIG_PINCTRL_QCOM_SC7280) += pinctrl-sc7280.o

  obj-$(CONFIG_PINCTRL_QCOM_SDM660) += pinctrl-sdm660.o obj-$(CONFIG_PINCTRL_QCOM_SDM845) += pinctrl-sdm845.o obj-$(CONFIG_PINCTRL_QCOM_SM6115) += pinctrl-sm6115.o +obj-$(CONFIG_PINCTRL_QCOM_SM7150) += pinctrl-sm7150.o obj-$(CONFIG_PINCTRL_QCOM_SM8150) += pinctrl-sm8150.o obj-$(CONFIG_PINCTRL_QCOM_SM8250) += pinctrl-sm8250.o obj-$(CONFIG_PINCTRL_QCOM_SM8550) += pinctrl-sm8550.o

drivers/pinctrl/ renamed from drivers/pinctrl/qcom/pinctrl-sm7150.c +0 -0

qcom/pinctrl-sm7150.c
new file mode 100644
index 00000000000..435ba39b1db

drivers/pinctrl/qcom/pinctrl-sm7150.c new file +91 -0
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Pinctrl driver for Qualcomm SM7150
+ *
+ * (C) Copyright 2025 Danila Tikhonov <[email protected]>
+ * (C) Copyright 2025 Jens Reidel <[email protected]>
+ *
+ * Based on Linux Kernel driver
+ */
+
+#include <dm.h>
+
+#include "pinctrl-qcom.h"
+
+#define WEST    0x00000000
+#define NORTH    0x00400000
+#define SOUTH    0x00800000
+
+#define MAX_PIN_NAME_LEN 32
+static char pin_name[MAX_PIN_NAME_LEN] __section(".data");
+
+static const struct pinctrl_function msm_pinctrl_functions[] = {
+    { "qup12", 1 },
+    { "gpio",  0 },
+    { "sdc2_clk", 0 } /* special pin GPIO124 */
+};
+
+#define SDC_QDSD_PINGROUP(pg_name, ctl, pull, drv)    \
+    {                        \
+        .name = pg_name,            \
+        .ctl_reg = ctl,                \
+        .io_reg = 0,                \
+        .pull_bit = pull,            \
+        .drv_bit = drv,                \
+        .oe_bit = -1,                \
+        .in_bit = -1,                \
+        .out_bit = -1,                \
+    }
+
+#define UFS_RESET(pg_name, offset)            \
+    {                        \
+        .name = pg_name,            \
+        .ctl_reg = offset,            \
+        .io_reg = offset + 0x4,            \
+        .pull_bit = 3,                \
+        .drv_bit = 0,                \
+        .oe_bit = -1,                \
+        .in_bit = -1,                \
+        .out_bit = 0,                \
+    }
+
+static const struct msm_special_pin_data msm_special_pins_data[] = {
+    [0] = UFS_RESET("ufs_reset", 0x9f000),
+    [1] = SDC_QDSD_PINGROUP("sdc1_rclk", WEST + 0x9a000, 15, 0),
+    [2] = SDC_QDSD_PINGROUP("sdc1_clk", WEST + 0x9a000, 13, 6),
+    [3] = SDC_QDSD_PINGROUP("sdc1_cmd", WEST + 0x9a000, 11, 3),
+    [4] = SDC_QDSD_PINGROUP("sdc1_data", WEST + 0x9a000, 9, 0),
+    [5] = SDC_QDSD_PINGROUP("sdc2_clk", SOUTH + 0x98000, 14, 6),
+    [6] = SDC_QDSD_PINGROUP("sdc2_cmd", SOUTH + 0x98000, 11, 3),
+    [7] = SDC_QDSD_PINGROUP("sdc2_data", SOUTH + 0x98000, 9, 0),
+};
+
+static const unsigned int sm7150_pin_offsets[] = {
+    [0] = SOUTH,    [1] = SOUTH,    [2] = SOUTH,    [3] = SOUTH,
+    [4] = NORTH,    [5] = NORTH,    [6] = NORTH,    [7] = NORTH,
+    [8] = NORTH,    [9] = NORTH,    [10] = NORTH,    [11] = NORTH,
+    [12] = SOUTH,    [13] = SOUTH,    [14] = SOUTH,    [15] = SOUTH,
+    [16] = SOUTH,    [17] = SOUTH,    [18] = SOUTH,    [19] = SOUTH,
+    [20] = SOUTH,    [21] = SOUTH,    [22] = SOUTH,    [23] = SOUTH,
+    [24] = SOUTH,    [25] = SOUTH,    [26] = SOUTH,    [27] = SOUTH,
+    [28] = SOUTH,    [29] = NORTH,    [30] = SOUTH,    [31] = WEST,
+    [32] = NORTH,    [33] = NORTH,    [34] = SOUTH,    [35] = SOUTH,
+    [36] = SOUTH,    [37] = SOUTH,    [38] = SOUTH,    [39] = SOUTH,
+    [40] = SOUTH,    [41] = SOUTH,    [42] = NORTH,    [43] = NORTH,
+    [44] = NORTH,    [45] = NORTH,    [46] = NORTH,    [47] = NORTH,
+    [48] = WEST,    [49] = WEST,    [50] = WEST,    [51] = WEST,
+    [52] = WEST,    [53] = WEST,    [54] = WEST,    [55] = WEST,
+    [56] = WEST,    [57] = WEST,    [58] = WEST,    [59] = NORTH,
+    [60] = NORTH,    [61] = NORTH,    [62] = NORTH,    [63] = NORTH,
+    [64] = NORTH,    [65] = NORTH,    [66] = NORTH,    [67] = NORTH,
+    [68] = NORTH,    [69] = NORTH,    [70] = NORTH,    [71] = NORTH,
+    [72] = NORTH,    [73] = NORTH,    [74] = WEST,    [75] = WEST,
+    [76] = WEST,    [77] = WEST,    [78] = WEST,    [79] = WEST,
+    [80] = WEST,    [81] = WEST,    [82] = WEST,    [83] = WEST,
+    [84] = WEST,    [85] = WEST,    [86] = NORTH,    [87] = NORTH,
+    [88] = NORTH,    [89] = NORTH,    [90] = NORTH,    [91] = NORTH,
+    [92] = NORTH,    [93] = NORTH,    [94] = SOUTH,    [95] = WEST,
+    [96] = WEST,    [97] = WEST,    [98] = WEST,    [99] = WEST,
+    [100] = WEST,    [101] = NORTH,    [102] = NORTH,    [103] = NORTH,
+    [104] = WEST,    [105] = NORTH,    [106] = NORTH,    [107] = WEST,
+    [108] = SOUTH,    [109] = SOUTH,    [110] = NORTH,    [111] =

NORTH,
+    [112] = NORTH,    [113] = NORTH,    [114] = NORTH,    [115] = NORTH,
+    [116] = NORTH,    [117] = NORTH,    [118] = NORTH,

drivers/pinctrl/qcom/pinctrl-sm7150.c new file +3 -0
+};
+
+static const char *sm7150_get_function_name(struct udevice *dev,

unsigned int selector)

drivers/pinctrl/qcom/pinctrl-sm7150.c line 104

Quoted 8 lines
drivers/pinctrl/qcom/pinctrl-sm7150.c new file +8 -0
+{
+    return msm_pinctrl_functions[selector].name;
+}
+
+static const char *sm7150_get_pin_name(struct udevice *dev,
+                       unsigned int selector)
+{
+    if (selector >= 119 && selector <= 126)

This should be && select <= 127, since there are 8 special pins. We should really update all the drivers to use ARRAY_LENGTH macros rather than doing all the maths by hand since so many have had errors at this point ahaha

Quoted 5 lines
Quoted 1 line

Kind regards,

Are you sure? I think this is correct, since start and end of the range are inclusive, so 119-126 are 8 GPIOs in total. The total pin count is also 126.

Damn you're totally right! Apologies.

I guess at least I demonstrated my point about these magic numbers being annoying to count XD

Kind regards,>

Quoted 43 lines

Best regards,
Jens

Quoted 40 lines
Quoted 39 lines

+        snprintf(pin_name, MAX_PIN_NAME_LEN,
+             msm_special_pins_data[selector - 119].name); +    else
+        snprintf(pin_name, MAX_PIN_NAME_LEN, "gpio%u", selector);

drivers/pinctrl/qcom/pinctrl-sm7150.c new file +5 -0
+
+    return pin_name;
+}
+
+static int sm7150_get_function_mux(__maybe_unused unsigned int pin,

unsigned int selector)

drivers/pinctrl/qcom/pinctrl-sm7150.c new file +29 -0
+{
+    return msm_pinctrl_functions[selector].val;
+}
+
+static struct msm_pinctrl_data sm7150_data = {
+    .pin_data = {
+        .pin_offsets = sm7150_pin_offsets,
+        .pin_count = 126,
+        .special_pins_start = 119,
+        .special_pins_data = msm_special_pins_data,
+    },
+    .functions_count = ARRAY_SIZE(msm_pinctrl_functions),
+    .get_function_name = sm7150_get_function_name,
+    .get_function_mux = sm7150_get_function_mux,
+    .get_pin_name = sm7150_get_pin_name,
+};
+
+static const struct udevice_id msm_pinctrl_ids[] = {
+    { .compatible = "qcom,sm7150-tlmm", .data = (ulong)&sm7150_data },
+    { /* sentinel */ }
+};
+
+U_BOOT_DRIVER(pinctrl_sm7150) = {
+    .name        = "pinctrl_sm7150",
+    .id        = UCLASS_NOP,
+    .of_match    = msm_pinctrl_ids,
+    .ops        = &msm_pinctrl_ops,
+    .bind        = msm_pinctrl_bind,
+};
Signature · 1 line
// Casey (she/her)
#7 lore raw

PATCH 3/4 phy: qcom-qmp-ufs: Import SM7150 tables from Linux

In reply to Jens Reidel

From: Danila Tikhonov <[email protected]>

Import the init sequence for the UFS on SM7150.

---
 drivers/phy/qcom/phy-qcom-qmp-ufs.c | 61 +++++++++++++++++++++++++++++
 1 file changed, 61 insertions(+)
drivers/phy/qcom/phy-qcom-qmp-ufs.c +61 -0
index f3c606847fb..a2a0e226f0c 100644
@@ -221,6 +221,36 @@ static const struct qmp_ufs_init_tbl sm8150_ufsphy_hs_g4_rx[] = {
 	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0x3c),
 };
 
+static const struct qmp_ufs_init_tbl sm7150_ufsphy_rx[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_LVL, 0x24),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x1e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_INTERFACE_MODE, 0x40),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_TERM_BW, 0x5b),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x1b),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SVS_SO_GAIN_HALF, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SVS_SO_GAIN_QUARTER, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SVS_SO_GAIN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x5b),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_PI_CONTROLS, 0x81),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_COUNT_LOW, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_MODE_00, 0x59),
+};
+
+static const struct qmp_ufs_init_tbl sm7150_ufsphy_pcs[] = {
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_RX_SIGDET_CTRL2, 0x6f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_TX_LARGE_AMP_DRV_LVL, 0x0f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_TX_SMALL_AMP_DRV_LVL, 0x02),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_RX_SYM_RESYNC_CTRL, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_RX_SIGDET_CTRL1, 0x0f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_RX_MIN_HIBERN8_TIME, 0xff),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
+};
+
 static const struct qmp_ufs_init_tbl sm8150_ufsphy_serdes[] = {
 	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_EN_SEL, 0xd9),
 	QMP_PHY_INIT_CFG(QSERDES_V4_COM_HSCLK_SEL, 0x11),
@@ -1018,6 +1048,36 @@ static const struct qmp_ufs_cfg sm8150_ufsphy_cfg = {
 	.no_pcs_sw_reset	= false,
 };
 
+static const struct qmp_ufs_cfg sm7150_ufsphy_cfg = {
+	.lanes			= 1,
+
+	.offsets		= &qmp_ufs_offsets,
+
+	.tbls = {
+		.serdes		= sdm845_ufsphy_serdes,
+		.serdes_num	= ARRAY_SIZE(sdm845_ufsphy_serdes),
+		.tx		= sdm845_ufsphy_tx,
+		.tx_num		= ARRAY_SIZE(sdm845_ufsphy_tx),
+		.rx		= sm7150_ufsphy_rx,
+		.rx_num		= ARRAY_SIZE(sm7150_ufsphy_rx),
+		.pcs		= sm7150_ufsphy_pcs,
+		.pcs_num	= ARRAY_SIZE(sm7150_ufsphy_pcs),
+	},
+	.tbls_hs_b = {
+		.serdes		= sdm845_ufsphy_hs_b_serdes,
+		.serdes_num	= ARRAY_SIZE(sdm845_ufsphy_hs_b_serdes),
+	},
+	.clk_list		= sdm845_ufs_phy_clk_l,
+	.num_clks		= ARRAY_SIZE(sdm845_ufs_phy_clk_l),
+	.vreg_list		= qmp_ufs_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_ufs_vreg_l),
+	.reset_list		= qmp_ufs_reset_l,
+	.num_resets		= ARRAY_SIZE(qmp_ufs_reset_l),
+	.regs			= ufsphy_v3_regs_layout,
+
+	.no_pcs_sw_reset	= true,
+};
+
 static const struct qmp_ufs_cfg sm8250_ufsphy_cfg = {
 	.lanes			= 2,
 
@@ -1593,6 +1653,7 @@ static struct phy_ops qmp_ufs_ops = {
 static const struct udevice_id qmp_ufs_ids[] = {
 	{ .compatible = "qcom,sa8775p-qmp-ufs-phy", .data = (ulong)&sa8775p_ufsphy_cfg, },
 	{ .compatible = "qcom,sdm845-qmp-ufs-phy", .data = (ulong)&sdm845_ufsphy_cfg },
+	{ .compatible = "qcom,sm7150-qmp-ufs-phy", .data = (ulong)&sm7150_ufsphy_cfg },
 	{ .compatible = "qcom,sm8150-qmp-ufs-phy", .data = (ulong)&sm8150_ufsphy_cfg },
 	{ .compatible = "qcom,sm8250-qmp-ufs-phy", .data = (ulong)&sm8250_ufsphy_cfg },
 	{ .compatible = "qcom,qcs8300-qmp-ufs-phy", .data = (ulong)&sa8775p_ufsphy_cfg },
Signature · 1 line
2.51.0
reviewer Reviewed-by on v1 3/4
#8 lore raw

Re: [PATCH 3/4] phy: qcom-qmp-ufs: Import SM7150 tables from Linux

Quoted 89 lines · Jens Reidel

From: Danila Tikhonov <[email protected]>

Import the init sequence for the UFS on SM7150.

---
  drivers/phy/qcom/phy-qcom-qmp-ufs.c | 61 +++++++++++++++++++++++++++++
  1 file changed, 61 insertions(+)
drivers/phy/qcom/phy-qcom-qmp-ufs.c +60 -0
index f3c606847fb..a2a0e226f0c 100644
@@ -221,6 +221,36 @@ static const struct qmp_ufs_init_tbl sm8150_ufsphy_hs_g4_rx[] = {
  	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0x3c),
  };
 
+static const struct qmp_ufs_init_tbl sm7150_ufsphy_rx[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_LVL, 0x24),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x1e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_INTERFACE_MODE, 0x40),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_TERM_BW, 0x5b),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x1b),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SVS_SO_GAIN_HALF, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SVS_SO_GAIN_QUARTER, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SVS_SO_GAIN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x5b),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_PI_CONTROLS, 0x81),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_COUNT_LOW, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_MODE_00, 0x59),
+};
+
+static const struct qmp_ufs_init_tbl sm7150_ufsphy_pcs[] = {
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_RX_SIGDET_CTRL2, 0x6f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_TX_LARGE_AMP_DRV_LVL, 0x0f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_TX_SMALL_AMP_DRV_LVL, 0x02),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_RX_SYM_RESYNC_CTRL, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_RX_SIGDET_CTRL1, 0x0f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_RX_MIN_HIBERN8_TIME, 0xff),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
+};
+
  static const struct qmp_ufs_init_tbl sm8150_ufsphy_serdes[] = {
  	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_EN_SEL, 0xd9),
  	QMP_PHY_INIT_CFG(QSERDES_V4_COM_HSCLK_SEL, 0x11),
@@ -1018,6 +1048,36 @@ static const struct qmp_ufs_cfg sm8150_ufsphy_cfg = {
  	.no_pcs_sw_reset	= false,
  };
 
+static const struct qmp_ufs_cfg sm7150_ufsphy_cfg = {
+	.lanes			= 1,
+
+	.offsets		= &qmp_ufs_offsets,
+
+	.tbls = {
+		.serdes		= sdm845_ufsphy_serdes,
+		.serdes_num	= ARRAY_SIZE(sdm845_ufsphy_serdes),
+		.tx		= sdm845_ufsphy_tx,
+		.tx_num		= ARRAY_SIZE(sdm845_ufsphy_tx),
+		.rx		= sm7150_ufsphy_rx,
+		.rx_num		= ARRAY_SIZE(sm7150_ufsphy_rx),
+		.pcs		= sm7150_ufsphy_pcs,
+		.pcs_num	= ARRAY_SIZE(sm7150_ufsphy_pcs),
+	},
+	.tbls_hs_b = {
+		.serdes		= sdm845_ufsphy_hs_b_serdes,
+		.serdes_num	= ARRAY_SIZE(sdm845_ufsphy_hs_b_serdes),
+	},
+	.clk_list		= sdm845_ufs_phy_clk_l,
+	.num_clks		= ARRAY_SIZE(sdm845_ufs_phy_clk_l),
+	.vreg_list		= qmp_ufs_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_ufs_vreg_l),
+	.reset_list		= qmp_ufs_reset_l,
+	.num_resets		= ARRAY_SIZE(qmp_ufs_reset_l),
+	.regs			= ufsphy_v3_regs_layout,
+
+	.no_pcs_sw_reset	= true,
+};
+
  static const struct qmp_ufs_cfg sm8250_ufsphy_cfg = {
  	.lanes			= 2,
 

drivers/phy/qcom/phy-qcom-qmp-ufs.c static struct phy_ops qmp_ufs_ops = { · line 1659

Quoted 7 lines
drivers/phy/qcom/phy-qcom-qmp-ufs.c +1 -0
@@ -1593,6 +1653,7 @@ static struct phy_ops qmp_ufs_ops = {
  static const struct udevice_id qmp_ufs_ids[] = {
  	{ .compatible = "qcom,sa8775p-qmp-ufs-phy", .data = (ulong)&sa8775p_ufsphy_cfg, },
  	{ .compatible = "qcom,sdm845-qmp-ufs-phy", .data = (ulong)&sdm845_ufsphy_cfg },
+	{ .compatible = "qcom,sm7150-qmp-ufs-phy", .data = (ulong)&sm7150_ufsphy_cfg },
  	{ .compatible = "qcom,sm8150-qmp-ufs-phy", .data = (ulong)&sm8150_ufsphy_cfg },
  	{ .compatible = "qcom,sm8250-qmp-ufs-phy", .data = (ulong)&sm8250_ufsphy_cfg },
  	{ .compatible = "qcom,qcs8300-qmp-ufs-phy", .data = (ulong)&sa8775p_ufsphy_cfg },
#9 lore raw

PATCH 4/4 configs: qcom_defconfig: Enable SM7150 GCC and Pinctrl

In reply to Jens Reidel

From: Danila Tikhonov <[email protected]>

Enable the necessary drivers so that SM7150 devices can boot with qcom_defconfig.

---
 configs/qcom_defconfig | 2 ++
 1 file changed, 2 insertions(+)
configs/qcom_defconfig +2 -0
index 86d7de89e77..42a25b4a18a 100644
@@ -60,6 +60,7 @@ CONFIG_CLK_QCOM_QCS8300=y
 CONFIG_CLK_QCOM_SA8775P=y
 CONFIG_CLK_QCOM_SDM845=y
 CONFIG_CLK_QCOM_SM6115=y
+CONFIG_CLK_QCOM_SM7150=y
 CONFIG_CLK_QCOM_SM8150=y
 CONFIG_CLK_QCOM_SM8250=y
 CONFIG_CLK_QCOM_SM8550=y
@@ -112,6 +113,7 @@ CONFIG_PINCTRL_QCOM_SA8775P=y
 CONFIG_PINCTRL_QCOM_SC7280=y
 CONFIG_PINCTRL_QCOM_SDM845=y
 CONFIG_PINCTRL_QCOM_SM6115=y
+CONFIG_PINCTRL_QCOM_SM7150=y
 CONFIG_PINCTRL_QCOM_SM8150=y
 CONFIG_PINCTRL_QCOM_SM8250=y
 CONFIG_PINCTRL_QCOM_SM8550=y
Signature · 1 line
2.51.0
Reviewed-by on v1 4/4
#10 lore raw

Re: [PATCH 4/4] configs: qcom_defconfig: Enable SM7150 GCC and Pinctrl

Quoted 7 lines · Jens Reidel

From: Danila Tikhonov <[email protected]>

Enable the necessary drivers so that SM7150 devices can boot with qcom_defconfig.

Quoted 23 lines
 configs/qcom_defconfig | 2 ++
 1 file changed, 2 insertions(+)
configs/qcom_defconfig +2 -0
index 86d7de89e77..42a25b4a18a 100644
@@ -60,6 +60,7 @@ CONFIG_CLK_QCOM_QCS8300=y
 CONFIG_CLK_QCOM_SA8775P=y
 CONFIG_CLK_QCOM_SDM845=y
 CONFIG_CLK_QCOM_SM6115=y
+CONFIG_CLK_QCOM_SM7150=y
 CONFIG_CLK_QCOM_SM8150=y
 CONFIG_CLK_QCOM_SM8250=y
 CONFIG_CLK_QCOM_SM8550=y
@@ -112,6 +113,7 @@ CONFIG_PINCTRL_QCOM_SA8775P=y
 CONFIG_PINCTRL_QCOM_SC7280=y
 CONFIG_PINCTRL_QCOM_SDM845=y
 CONFIG_PINCTRL_QCOM_SM6115=y
+CONFIG_PINCTRL_QCOM_SM7150=y
 CONFIG_PINCTRL_QCOM_SM8150=y
 CONFIG_PINCTRL_QCOM_SM8250=y
 CONFIG_PINCTRL_QCOM_SM8550=y
Signature · 1 line
// Casey (she/her)