5.15.191-rc1 review

This is the start of the stable review cycle for the 5.15.191 release. There are 33 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Thu, 04 Sep 2025 13:19:14 +0000. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

	https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.15.191-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-5.15.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <[email protected]>

    Linux 5.15.191-rc1

Eric Sandeen <[email protected]>
xfs: do not propagate ENODATA disk errors into xattr code

Imre Deak <[email protected]>
Revert "drm/dp: Change AUX DPCD probe address from DPCD_REV to LANE0_1_STATUS"

Hamish Martin <[email protected]>
HID: mcp2221: Handle reads greater than 60 bytes

Hamish Martin <[email protected]>
HID: mcp2221: Don't set bus speed on every transfer

James Jones <[email protected]>
drm/nouveau/disp: Always accept linear modifier

Fabio Porcedda <[email protected]>
net: usb: qmi_wwan: add Telit Cinterion LE910C4-WWX new compositions

Shanker Donthineni <[email protected]>
dma/pool: Ensure DMA_DIRECT_REMAP allocations are decrypted

Alex Deucher <[email protected]>
Revert "drm/amdgpu: fix incorrect vm flags to map bo"

Minjong Kim <[email protected]>
HID: hid-ntrig: fix unable to handle page fault in ntrig_report_version()

Ping Cheng <[email protected]>
HID: wacom: Add a new Art Pen 2

Qasim Ijaz <[email protected]>
HID: multitouch: fix slab out-of-bounds access in mt_report_fixup()

Qasim Ijaz <[email protected]>
HID: asus: fix UAF via HID_CLAIMED_INPUT validation

Thijs Raymakers <[email protected]>
KVM: x86: use array_index_nospec with indices that come from guest

Li Nan <[email protected]>
efivarfs: Fix slab-out-of-bounds in efivarfs_d_compare

Eric Dumazet <[email protected]>
sctp: initialize more fields in sctp_v6_from_sk()

Rohan G Thomas <[email protected]>
net: stmmac: xgmac: Do not enable RX FIFO Overflow interrupts

Alexei Lazar <[email protected]>
net/mlx5e: Set local Xoff after FW update

Alexei Lazar <[email protected]>
net/mlx5e: Update and set Xon/Xoff upon port speed set

Alexei Lazar <[email protected]>
net/mlx5e: Update and set Xon/Xoff upon MTU set

Horatiu Vultur <[email protected]>
phy: mscc: Fix when PTP clock is register and unregister

Yeounsu Moon <[email protected]>
net: dlink: fix multicast stats being counted incorrectly

Kuniyuki Iwashima <[email protected]>
atm: atmtcp: Prevent arbitrary write in atmtcp_recv_control().

Luiz Augusto von Dentz <[email protected]>
Bluetooth: hci_event: Detect if HCI_EV_NUM_COMP_PKTS is unbalanced

Madhavan Srinivasan <[email protected]>
powerpc/kvm: Fix ifdef to remove build warning

Oscar Maes <[email protected]>
net: ipv4: fix regression in local-broadcast routes

Jan Kara <[email protected]>
udf: Fix directory iteration for longer tail extents

Nikolay Kuratov <[email protected]>
vhost/net: Protect ubufs with rcu read lock in vhost_net_ubuf_put()

Trond Myklebust <[email protected]>
NFS: Fix a race when updating an existing write

Christoph Hellwig <[email protected]>
nfs: fold nfs_page_group_lock_subrequests into nfs_lock_and_join_requests

Alexey Klimov <[email protected]>
ASoC: codecs: tx-macro: correct tx_macro_component_drv name

Damien Le Moal <[email protected]>
scsi: core: sysfs: Correct sysfs attributes access rights

Tengda Wu <[email protected]>
ftrace: Fix potential warning in trace_printk_seq during ftrace_dump

Randy Dunlap <[email protected]>
pinctrl: STMFX: add missing HAS_IOMEM dependency

-------------

Diffstat:

 Makefile                                           |   4 +-
 arch/powerpc/kernel/kvm.c                          |   8 +-
 arch/x86/kvm/lapic.c                               |   2 +
 arch/x86/kvm/x86.c                                 |   7 +-
 drivers/atm/atmtcp.c                               |  17 ++-
 drivers/gpu/drm/amd/amdgpu/amdgpu_csa.c            |   4 +-
 drivers/gpu/drm/drm_dp_helper.c                    |   2 +-
 drivers/gpu/drm/nouveau/dispnv50/wndw.c            |   4 +
 drivers/hid/hid-asus.c                             |   8 +-
 drivers/hid/hid-mcp2221.c                          |  71 +++++++----
 drivers/hid/hid-multitouch.c                       |   8 ++
 drivers/hid/hid-ntrig.c                            |   3 +
 drivers/hid/wacom_wac.c                            |   1 +
 drivers/net/ethernet/dlink/dl2k.c                  |   2 +-
 .../ethernet/mellanox/mlx5/core/en/port_buffer.c   |   3 +-
 .../ethernet/mellanox/mlx5/core/en/port_buffer.h   |  12 ++
 drivers/net/ethernet/mellanox/mlx5/core/en_main.c  |  19 ++-
 drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c |   4 -
 drivers/net/phy/mscc/mscc.h                        |   4 +
 drivers/net/phy/mscc/mscc_main.c                   |   4 +-
 drivers/net/phy/mscc/mscc_ptp.c                    |  34 +++--
 drivers/net/usb/qmi_wwan.c                         |   3 +
 drivers/pinctrl/Kconfig                            |   1 +
 drivers/scsi/scsi_sysfs.c                          |   4 +-
 drivers/vhost/net.c                                |   9 +-
 fs/efivarfs/super.c                                |   4 +
 fs/nfs/pagelist.c                                  |  86 +------------
 fs/nfs/write.c                                     | 142 +++++++++++++--------
 fs/udf/directory.c                                 |   2 +-
 fs/xfs/libxfs/xfs_attr_remote.c                    |   7 +
 fs/xfs/libxfs/xfs_da_btree.c                       |   6 +
 include/linux/atmdev.h                             |   1 +
 include/linux/nfs_page.h                           |   2 +-
 kernel/dma/pool.c                                  |   4 +-
 kernel/trace/trace.c                               |   4 +-
 net/atm/common.c                                   |  15 ++-
 net/bluetooth/hci_event.c                          |  12 +-
 net/ipv4/route.c                                   |  10 +-
 net/sctp/ipv6.c                                    |   2 +
 sound/soc/codecs/lpass-tx-macro.c                  |   2 +-
 40 files changed, 328 insertions(+), 209 deletions(-)

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Randy Dunlap <[email protected]>

[ Upstream commit a12946bef0407cf2db0899c83d42c47c00af3fbc ]

When building on ARCH=um (which does not set HAS_IOMEM), kconfig reports an unmet dependency caused by PINCTRL_STMFX. It selects MFD_STMFX, which depends on HAS_IOMEM. To stop this warning, PINCTRL_STMFX should also depend on HAS_IOMEM.

kconfig warning:
WARNING: unmet direct dependencies detected for MFD_STMFX
Depends on [n]: HAS_IOMEM [=n] && I2C [=y] && OF [=y] Selected by [y]:
- PINCTRL_STMFX [=y] && PINCTRL [=y] && I2C [=y] && OF_GPIO [=y]

---
 drivers/pinctrl/Kconfig | 1 +
 1 file changed, 1 insertion(+)

index 31921108e4569..546a8f1bb10bc 100644
@@ -269,6 +269,7 @@ config PINCTRL_STMFX
 	tristate "STMicroelectronics STMFX GPIO expander pinctrl driver"
 	depends on I2C
 	depends on OF_GPIO
+	depends on HAS_IOMEM
 	select GENERIC_PINCONF
 	select GPIOLIB_IRQCHIP
 	select MFD_STMFX

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Tengda Wu <[email protected]>

[ Upstream commit 4013aef2ced9b756a410f50d12df9ebe6a883e4a ]

When calling ftrace_dump_one() concurrently with reading trace_pipe, a WARN_ON_ONCE() in trace_printk_seq() can be triggered due to a race condition.

The issue occurs because:

CPU0 (ftrace_dump) CPU1 (reader)
echo z > /proc/sysrq-trigger

!trace_empty(&iter)
trace_iterator_reset(&iter) <- len = size = 0
cat /sys/kernel/tracing/trace_pipe
trace_find_next_entry_inc(&iter)
__find_next_entry
ring_buffer_empty_cpu <- all empty
return NULL

trace_printk_seq(&iter.seq)
WARN_ON_ONCE(s->seq.len >= s->seq.size)

In the context between trace_empty() and trace_find_next_entry_inc() during ftrace_dump, the ring buffer data was consumed by other readers. This caused trace_find_next_entry_inc to return NULL, failing to populate iter.seq. At this point, due to the prior trace_iterator_reset, both iter.seq.len and iter.seq.size were set to 0. Since they are equal, the WARN_ON_ONCE condition is triggered.

Move the trace_printk_seq() into the if block that checks to make sure the return value of trace_find_next_entry_inc() is non-NULL in ftrace_dump_one(), ensuring the 'iter.seq' is properly populated before subsequent operations.

---
 kernel/trace/trace.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

index 23f6a9941be1d..7af8bbc57531c 100644
@@ -10122,10 +10122,10 @@ void ftrace_dump(enum ftrace_dump_mode oops_dump_mode)
 			ret = print_trace_line(&iter);
 			if (ret != TRACE_TYPE_NO_CONSUME)
 				trace_consume(&iter);
+
+			trace_printk_seq(&iter.seq);
 		}
 		touch_nmi_watchdog();
-
-		trace_printk_seq(&iter.seq);
 	}
 
 	if (!cnt)

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Damien Le Moal <[email protected]>

[ Upstream commit a2f54ff15c3bdc0132e20aae041607e2320dbd73 ]

The SCSI sysfs attributes "supported_mode" and "active_mode" do not define a store method and thus cannot be modified. Correct the DEVICE_ATTR() call for these two attributes to not include S_IWUSR to allow write access as they are read-only.

---
 drivers/scsi/scsi_sysfs.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

index 4c72116c8693c..7d3cbf4e6bc6e 100644
@@ -265,7 +265,7 @@ show_shost_supported_mode(struct device *dev, struct device_attribute *attr,
 	return show_shost_mode(supported_mode, buf);
 }
 
-static DEVICE_ATTR(supported_mode, S_IRUGO | S_IWUSR, show_shost_supported_mode, NULL);
+static DEVICE_ATTR(supported_mode, S_IRUGO, show_shost_supported_mode, NULL);
 
 static ssize_t
 show_shost_active_mode(struct device *dev,

@@ -279,7 +279,7 @@ show_shost_active_mode(struct device *dev,
 		return show_shost_mode(shost->active_mode, buf);
 }
 
-static DEVICE_ATTR(active_mode, S_IRUGO | S_IWUSR, show_shost_active_mode, NULL);
+static DEVICE_ATTR(active_mode, S_IRUGO, show_shost_active_mode, NULL);
 
 static int check_reset_type(const char *str)
 {

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alexey Klimov <[email protected]>

[ Upstream commit 43e0da37d5cfb23eec6aeee9422f84d86621ce2b ]

We already have a component driver named "RX-MACRO", which is lpass-rx-macro.c. The tx macro component driver's name should be "TX-MACRO" accordingly. Fix it.

---
 sound/soc/codecs/lpass-tx-macro.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index 4377e91733b87..095c6dc564465 100644
@@ -1782,7 +1782,7 @@ static int tx_macro_register_mclk_output(struct tx_macro *tx)
 }
 
 static const struct snd_soc_component_driver tx_macro_component_drv = {
-	.name = "RX-MACRO",
+	.name = "TX-MACRO",
 	.probe = tx_macro_component_probe,
 	.controls = tx_macro_snd_controls,
 	.num_controls = ARRAY_SIZE(tx_macro_snd_controls),

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Christoph Hellwig <[email protected]>

commit 25edbcac6e32eab345e470d56ca9974a577b878b upstream.

Fold nfs_page_group_lock_subrequests into nfs_lock_and_join_requests to prepare for future changes to this code, and move the helpers to write.c as well.

---
 fs/nfs/pagelist.c        |   77 -----------------------------------------------
 fs/nfs/write.c           |   74 +++++++++++++++++++++++++++++++++++++++++----
 include/linux/nfs_page.h |    1 
 3 files changed, 68 insertions(+), 84 deletions(-)

@@ -168,83 +168,6 @@ nfs_page_group_lock_head(struct nfs_page
 }
 
 /*
- * nfs_unroll_locks -  unlock all newly locked reqs and wait on @req
- * @head: head request of page group, must be holding head lock
- * @req: request that couldn't lock and needs to wait on the req bit lock
- *
- * This is a helper function for nfs_lock_and_join_requests
- * returns 0 on success, < 0 on error.
- */
-static void
-nfs_unroll_locks(struct nfs_page *head, struct nfs_page *req)
-{
-	struct nfs_page *tmp;
-
-	/* relinquish all the locks successfully grabbed this run */
-	for (tmp = head->wb_this_page ; tmp != req; tmp = tmp->wb_this_page) {
-		if (!kref_read(&tmp->wb_kref))
-			continue;
-		nfs_unlock_and_release_request(tmp);
-	}
-}
-
-/*
- * nfs_page_group_lock_subreq -  try to lock a subrequest
- * @head: head request of page group
- * @subreq: request to lock
- *
- * This is a helper function for nfs_lock_and_join_requests which
- * must be called with the head request and page group both locked.
- * On error, it returns with the page group unlocked.
- */
-static int
-nfs_page_group_lock_subreq(struct nfs_page *head, struct nfs_page *subreq)
-{
-	int ret;
-
-	if (!kref_get_unless_zero(&subreq->wb_kref))
-		return 0;
-	while (!nfs_lock_request(subreq)) {
-		nfs_page_group_unlock(head);
-		ret = nfs_wait_on_request(subreq);
-		if (!ret)
-			ret = nfs_page_group_lock(head);
-		if (ret < 0) {
-			nfs_unroll_locks(head, subreq);
-			nfs_release_request(subreq);
-			return ret;
-		}
-	}
-	return 0;
-}
-
-/*
- * nfs_page_group_lock_subrequests -  try to lock the subrequests
- * @head: head request of page group
- *
- * This is a helper function for nfs_lock_and_join_requests which
- * must be called with the head request locked.
- */
-int nfs_page_group_lock_subrequests(struct nfs_page *head)
-{
-	struct nfs_page *subreq;
-	int ret;
-
-	ret = nfs_page_group_lock(head);
-	if (ret < 0)
-		return ret;
-	/* lock each request in the page group */
-	for (subreq = head->wb_this_page; subreq != head;
-			subreq = subreq->wb_this_page) {
-		ret = nfs_page_group_lock_subreq(head, subreq);
-		if (ret < 0)
-			return ret;
-	}
-	nfs_page_group_unlock(head);
-	return 0;
-}
-
-/*
  * nfs_page_set_headlock - set the request PG_HEADLOCK
  * @req: request that is to be locked
  *

@@ -144,7 +144,6 @@ extern  int nfs_wait_on_request(struct n
 extern	void nfs_unlock_request(struct nfs_page *req);
 extern	void nfs_unlock_and_release_request(struct nfs_page *);
 extern	struct nfs_page *nfs_page_group_lock_head(struct nfs_page *req);
-extern	int nfs_page_group_lock_subrequests(struct nfs_page *head);
 extern void nfs_join_page_group(struct nfs_page *head,
 				struct nfs_commit_info *cinfo,
 				struct inode *inode);

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Trond Myklebust <[email protected]>

commit 76d2e3890fb169168c73f2e4f8375c7cc24a765e upstream.

After nfs_lock_and_join_requests() tests for whether the request is still attached to the mapping, nothing prevents a call to nfs_inode_remove_request() from succeeding until we actually lock the page group.
The reason is that whoever called nfs_inode_remove_request() doesn't necessarily have a lock on the page group head.

So in order to avoid races, let's take the page group lock earlier in nfs_lock_and_join_requests(), and hold it across the removal of the request in nfs_inode_remove_request().

---
 fs/nfs/pagelist.c        |    9 +++---
 fs/nfs/write.c           |   66 ++++++++++++++++-------------------------------
 include/linux/nfs_page.h |    1 
 3 files changed, 29 insertions(+), 47 deletions(-)

@@ -234,13 +234,14 @@ nfs_page_group_unlock(struct nfs_page *r
 	nfs_page_clear_headlock(req);
 }
 
-/*
- * nfs_page_group_sync_on_bit_locked
+/**
+ * nfs_page_group_sync_on_bit_locked - Test if all requests have @bit set
+ * @req: request in page group
+ * @bit: PG_* bit that is used to sync page group
  *
  * must be called with page group lock held
  */
-static bool
-nfs_page_group_sync_on_bit_locked(struct nfs_page *req, unsigned int bit)
+bool nfs_page_group_sync_on_bit_locked(struct nfs_page *req, unsigned int bit)
 {
 	struct nfs_page *head = req->wb_head;
 	struct nfs_page *tmp;

@@ -150,6 +150,7 @@ extern void nfs_join_page_group(struct n
 extern int nfs_page_group_lock(struct nfs_page *);
 extern void nfs_page_group_unlock(struct nfs_page *);
 extern bool nfs_page_group_sync_on_bit(struct nfs_page *, unsigned int);
+extern bool nfs_page_group_sync_on_bit_locked(struct nfs_page *, unsigned int);
 extern	int nfs_page_set_headlock(struct nfs_page *req);
 extern void nfs_page_clear_headlock(struct nfs_page *req);
 extern bool nfs_async_iocounter_wait(struct rpc_task *, struct nfs_lock_context *);

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nikolay Kuratov <[email protected]>

commit dd54bcf86c91a4455b1f95cbc8e9ac91205f3193 upstream.

When operating on struct vhost_net_ubuf_ref, the following execution sequence is theoretically possible:
CPU0 is finalizing DMA operation CPU1 is doing VHOST_NET_SET_BACKEND

                             // ubufs->refcount == 2
vhost_net_ubuf_put()                               vhost_net_ubuf_put_wait_and_free(oldubufs)
                                                     vhost_net_ubuf_put_and_wait()
                                                       vhost_net_ubuf_put()
                                                         int r = atomic_sub_return(1, &ubufs->refcount);
                                                         // r = 1
int r = atomic_sub_return(1, &ubufs->refcount);
// r = 0
                                                      wait_event(ubufs->wait, !atomic_read(&ubufs->refcount));
                                                      // no wait occurs here because condition is already true
                                                    kfree(ubufs);

if (unlikely(!r))
wake_up(&ubufs->wait); // use-after-free

This leads to use-after-free on ubufs access. This happens because CPU1 skips waiting for wake_up() when refcount is already zero.

To prevent that use a read-side RCU critical section in vhost_net_ubuf_put(), as suggested by Hillf Danton. For this lock to take effect, free ubufs with kfree_rcu().

Message-Id: <[email protected]>

---
 drivers/vhost/net.c |    9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

@@ -95,6 +95,7 @@ struct vhost_net_ubuf_ref {
 	atomic_t refcount;
 	wait_queue_head_t wait;
 	struct vhost_virtqueue *vq;
+	struct rcu_head rcu;
 };
 
 #define VHOST_NET_BATCH 64

@@ -248,9 +249,13 @@ vhost_net_ubuf_alloc(struct vhost_virtqu
 
 static int vhost_net_ubuf_put(struct vhost_net_ubuf_ref *ubufs)
 {
-	int r = atomic_sub_return(1, &ubufs->refcount);
+	int r;
+
+	rcu_read_lock();
+	r = atomic_sub_return(1, &ubufs->refcount);
 	if (unlikely(!r))
 		wake_up(&ubufs->wait);
+	rcu_read_unlock();
 	return r;
 }
 

@@ -263,7 +268,7 @@ static void vhost_net_ubuf_put_and_wait(
 static void vhost_net_ubuf_put_wait_and_free(struct vhost_net_ubuf_ref *ubufs)
 {
 	vhost_net_ubuf_put_and_wait(ubufs);
-	kfree(ubufs);
+	kfree_rcu(ubufs, rcu);
 }
 
 static void vhost_net_clear_ubuf_info(struct vhost_net *n)

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Jan Kara <[email protected]>

commit 1ea1cd11c72d1405a6b98440a9d5ea82dfa07166 upstream.

When directory's last extent has more that one block and its length is not multiple of a block side, the code wrongly decided to move to the next extent instead of processing the last partial block. This led to directory corruption. Fix the rounding issue.

---
 fs/udf/directory.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -171,7 +171,7 @@ static struct buffer_head *udf_fiiter_br
 static int udf_fiiter_advance_blk(struct udf_fileident_iter *iter)
 {
 	iter->loffset++;
-	if (iter->loffset < iter->elen >> iter->dir->i_blkbits)
+	if (iter->loffset < DIV_ROUND_UP(iter->elen, 1<<iter->dir->i_blkbits))
 		return 0;
 
 	iter->loffset = 0;

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Oscar Maes <[email protected]>

[ Upstream commit 5189446ba995556eaa3755a6e875bc06675b88bd ]

Commit 9e30ecf23b1b ("net: ipv4: fix incorrect MTU in broadcast routes") introduced a regression where local-broadcast packets would have their gateway set in __mkroute_output, which was caused by fi = NULL being removed.

Fix this by resetting the fib_info for local-broadcast packets. This preserves the intended changes for directed-broadcast packets.

---
 net/ipv4/route.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

index df4cbf9ba288f..b24de1c67d0c2 100644
@@ -2552,12 +2552,16 @@ static struct rtable *__mkroute_output(const struct fib_result *res,
 		    !netif_is_l3_master(dev_out))
 			return ERR_PTR(-EINVAL);
 
-	if (ipv4_is_lbcast(fl4->daddr))
+	if (ipv4_is_lbcast(fl4->daddr)) {
 		type = RTN_BROADCAST;
-	else if (ipv4_is_multicast(fl4->daddr))
+
+		/* reset fi to prevent gateway resolution */
+		fi = NULL;
+	} else if (ipv4_is_multicast(fl4->daddr)) {
 		type = RTN_MULTICAST;
-	else if (ipv4_is_zeronet(fl4->daddr))
+	} else if (ipv4_is_zeronet(fl4->daddr)) {
 		return ERR_PTR(-EINVAL);
+	}
 
 	if (dev_out->flags & IFF_LOOPBACK)
 		flags |= RTCF_LOCAL;

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Madhavan Srinivasan <[email protected]>

[ Upstream commit 88688a2c8ac6c8036d983ad8b34ce191c46a10aa ]

When compiling for pseries or powernv defconfig with "make C=1", these warning were reported bu sparse tool in powerpc/kernel/kvm.c

arch/powerpc/kernel/kvm.c:635:9: warning: switch with no cases arch/powerpc/kernel/kvm.c:646:9: warning: switch with no cases

Currently #ifdef were added after the switch case which are specific for BOOKE and PPC_BOOK3S_32. These are not enabled in pseries/powernv defconfig. Fix it by moving the #ifdef before switch(){}

---
 arch/powerpc/kernel/kvm.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

index 6568823cf3063..5d9d38834507d 100644
@@ -632,19 +632,19 @@ static void __init kvm_check_ins(u32 *inst, u32 features)
 #endif
 	}
 
-	switch (inst_no_rt & ~KVM_MASK_RB) {
 #ifdef CONFIG_PPC_BOOK3S_32
+	switch (inst_no_rt & ~KVM_MASK_RB) {
 	case KVM_INST_MTSRIN:
 		if (features & KVM_MAGIC_FEAT_SR) {
 			u32 inst_rb = _inst & KVM_MASK_RB;
 			kvm_patch_ins_mtsrin(inst, inst_rt, inst_rb);
 		}
 		break;
-#endif
 	}
+#endif
 
-	switch (_inst) {
 #ifdef CONFIG_BOOKE
+	switch (_inst) {
 	case KVM_INST_WRTEEI_0:
 		kvm_patch_ins_wrteei_0(inst);
 		break;

@@ -652,8 +652,8 @@ static void __init kvm_check_ins(u32 *inst, u32 features)
 	case KVM_INST_WRTEEI_1:
 		kvm_patch_ins_wrtee(inst, 0, 1);
 		break;
-#endif
 	}
+#endif
 }
 
 extern u32 kvm_template_start[];

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Luiz Augusto von Dentz <[email protected]>

[ Upstream commit 15bf2c6391bafb14a3020d06ec0761bce0803463 ]

This attempts to detect if HCI_EV_NUM_COMP_PKTS contain an unbalanced (more than currently considered outstanding) number of packets otherwise it could cause the hcon->sent to underflow and loop around breaking the tracking of the outstanding packets pending acknowledgment.

---
 net/bluetooth/hci_event.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)

index 84b07b27b3cf4..cfdaaecf78600 100644
@@ -3919,7 +3919,17 @@ static void hci_num_comp_pkts_evt(struct hci_dev *hdev, struct sk_buff *skb)
 		if (!conn)
 			continue;
 
-		conn->sent -= count;
+		/* Check if there is really enough packets outstanding before
+		 * attempting to decrease the sent counter otherwise it could
+		 * underflow..
+		 */
+		if (conn->sent >= count) {
+			conn->sent -= count;
+		} else {
+			bt_dev_warn(hdev, "hcon %p sent %u < count %u",
+				    conn, conn->sent, count);
+			conn->sent = 0;
+		}
 
 		switch (conn->type) {
 		case ACL_LINK:

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Kuniyuki Iwashima <[email protected]>

[ Upstream commit ec79003c5f9d2c7f9576fc69b8dbda80305cbe3a ]

syzbot reported the splat below. [0]

When atmtcp_v_open() or atmtcp_v_close() is called via connect() or close(), atmtcp_send_control() is called to send an in-kernel special message.

The message has ATMTCP_HDR_MAGIC in atmtcp_control.hdr.length. Also, a pointer of struct atm_vcc is set to atmtcp_control.vcc.

The notable thing is struct atmtcp_control is uAPI but has a space for an in-kernel pointer.

  struct atmtcp_control {
  	struct atmtcp_hdr hdr;	/* must be first */
  ...
  	atm_kptr_t vcc;		/* both directions */
  ...
  } __ATM_API_ALIGN;

  typedef struct { unsigned char _[8]; } __ATM_API_ALIGN atm_kptr_t;

The special message is processed in atmtcp_recv_control() called from atmtcp_c_send().

atmtcp_c_send() is vcc->dev->ops->send() and called from 2 paths:

1. .ndo_start_xmit() (vcc->send() == atm_send_aal0())
2. vcc_sendmsg()

The problem is sendmsg() does not validate the message length and userspace can abuse atmtcp_recv_control() to overwrite any kptr by atmtcp_control.

Let's add a new ->pre_send() hook to validate messages from sendmsg().

[0]:

Oops: general protection fault, probably for non-canonical address 0xdffffc00200000ab: 0000 [#1] SMP KASAN PTI
KASAN: probably user-memory-access in range [0x0000000100000558-0x000000010000055f]
CPU: 0 UID: 0 PID: 5865 Comm: syz-executor331 Not tainted 6.17.0-rc1-syzkaller-00215-gbab3ce404553 #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/12/2025
RIP: 0010:atmtcp_recv_control drivers/atm/atmtcp.c:93 [inline]
RIP: 0010:atmtcp_c_send+0x1da/0x950 drivers/atm/atmtcp.c:297
Code: 4d 8d 75 1a 4c 89 f0 48 c1 e8 03 42 0f b6 04 20 84 c0 0f 85 15 06 00 00 41 0f b7 1e 4d 8d b7 60 05 00 00 4c 89 f0 48 c1 e8 03 <42> 0f b6 04 20 84 c0 0f 85 13 06 00 00 66 41 89 1e 4d 8d 75 1c 4c
RSP: 0018:ffffc90003f5f810 EFLAGS: 00010203
RAX: 00000000200000ab RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff88802a510000 RSI: 00000000ffffffff RDI: ffff888030a6068c
RBP: ffff88802699fb40 R08: ffff888030a606eb R09: 1ffff1100614c0dd
R10: dffffc0000000000 R11: ffffffff8718fc40 R12: dffffc0000000000
R13: ffff888030a60680 R14: 000000010000055f R15: 00000000ffffffff
FS:  00007f8d7e9236c0(0000) GS:ffff888125c1c000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000045ad50 CR3: 0000000075bde000 CR4: 00000000003526f0
Call Trace:
 <TASK>
 vcc_sendmsg+0xa10/0xc60 net/atm/common.c:645
 sock_sendmsg_nosec net/socket.c:714 [inline]
 __sock_sendmsg+0x219/0x270 net/socket.c:729
 ____sys_sendmsg+0x505/0x830 net/socket.c:2614
 ___sys_sendmsg+0x21f/0x2a0 net/socket.c:2668
 __sys_sendmsg net/socket.c:2700 [inline]
 __do_sys_sendmsg net/socket.c:2705 [inline]
 __se_sys_sendmsg net/socket.c:2703 [inline]
 __x64_sys_sendmsg+0x19b/0x260 net/socket.c:2703
 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
 do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
 entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f8d7e96a4a9
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 51 18 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f8d7e923198 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f8d7e9f4308 RCX: 00007f8d7e96a4a9
RDX: 0000000000000000 RSI: 0000200000000240 RDI: 0000000000000005
RBP: 00007f8d7e9f4300 R08: 65732f636f72702f R09: 65732f636f72702f
R10: 65732f636f72702f R11: 0000000000000246 R12: 00007f8d7e9c10ac
R13: 00007f8d7e9231a0 R14: 0000200000000200 R15: 0000200000000250
 </TASK>
Modules linked in:

---
 drivers/atm/atmtcp.c   | 17 ++++++++++++++---
 include/linux/atmdev.h |  1 +
 net/atm/common.c       | 15 ++++++++++++---
 3 files changed, 27 insertions(+), 6 deletions(-)

index ff558908897f3..9c83fb29b2f1b 100644
@@ -279,6 +279,19 @@ static struct atm_vcc *find_vcc(struct atm_dev *dev, short vpi, int vci)
         return NULL;
 }
 
+static int atmtcp_c_pre_send(struct atm_vcc *vcc, struct sk_buff *skb)
+{
+	struct atmtcp_hdr *hdr;
+
+	if (skb->len < sizeof(struct atmtcp_hdr))
+		return -EINVAL;
+
+	hdr = (struct atmtcp_hdr *)skb->data;
+	if (hdr->length == ATMTCP_HDR_MAGIC)
+		return -EINVAL;
+
+	return 0;
+}
 
 static int atmtcp_c_send(struct atm_vcc *vcc,struct sk_buff *skb)
 {

@@ -288,9 +301,6 @@ static int atmtcp_c_send(struct atm_vcc *vcc,struct sk_buff *skb)
 	struct sk_buff *new_skb;
 	int result = 0;
 
-	if (skb->len < sizeof(struct atmtcp_hdr))
-		goto done;
-
 	dev = vcc->dev_data;
 	hdr = (struct atmtcp_hdr *) skb->data;
 	if (hdr->length == ATMTCP_HDR_MAGIC) {

@@ -347,6 +357,7 @@ static const struct atmdev_ops atmtcp_v_dev_ops = {
 
 static const struct atmdev_ops atmtcp_c_dev_ops = {
 	.close		= atmtcp_c_close,
+	.pre_send	= atmtcp_c_pre_send,
 	.send		= atmtcp_c_send
 };
 

index 45f2f278b50a8..70807c679f1ab 100644
@@ -185,6 +185,7 @@ struct atmdev_ops { /* only send is required */
 	int (*compat_ioctl)(struct atm_dev *dev,unsigned int cmd,
 			    void __user *arg);
 #endif
+	int (*pre_send)(struct atm_vcc *vcc, struct sk_buff *skb);
 	int (*send)(struct atm_vcc *vcc,struct sk_buff *skb);
 	int (*send_bh)(struct atm_vcc *vcc, struct sk_buff *skb);
 	int (*send_oam)(struct atm_vcc *vcc,void *cell,int flags);

index 930eb302cd10f..38ed7b985f655 100644
@@ -635,18 +635,27 @@ int vcc_sendmsg(struct socket *sock, struct msghdr *m, size_t size)
 
 	skb->dev = NULL; /* for paths shared with net_device interfaces */
 	if (!copy_from_iter_full(skb_put(skb, size), size, &m->msg_iter)) {
-		atm_return_tx(vcc, skb);
-		kfree_skb(skb);
 		error = -EFAULT;
-		goto out;
+		goto free_skb;
 	}
 	if (eff != size)
 		memset(skb->data + size, 0, eff-size);
+
+	if (vcc->dev->ops->pre_send) {
+		error = vcc->dev->ops->pre_send(vcc, skb);
+		if (error)
+			goto free_skb;
+	}
+
 	error = vcc->dev->ops->send(vcc, skb);
 	error = error ? error : size;
 out:
 	release_sock(sk);
 	return error;
+free_skb:
+	atm_return_tx(vcc, skb);
+	kfree_skb(skb);
+	goto out;
 }
 
 __poll_t vcc_poll(struct file *file, struct socket *sock, poll_table *wait)

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Yeounsu Moon <[email protected]>

[ Upstream commit 007a5ffadc4fd51739527f1503b7cf048f31c413 ]

McstFramesRcvdOk counts the number of received multicast packets, and it reports the value correctly.

However, reading McstFramesRcvdOk clears the register to zero. As a result, the driver was reporting only the packets since the last read, instead of the accumulated total.

Fix this by updating the multicast statistics accumulatively instaed of instantaneously.

Tested-on: D-Link DGE-550T Rev-A3

---
 drivers/net/ethernet/dlink/dl2k.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index 09a275eb44487..81395852b4d43 100644
@@ -1095,7 +1095,7 @@ get_stats (struct net_device *dev)
 	dev->stats.rx_bytes += dr32(OctetRcvOk);
 	dev->stats.tx_bytes += dr32(OctetXmtOk);
 
-	dev->stats.multicast = dr32(McstFramesRcvdOk);
+	dev->stats.multicast += dr32(McstFramesRcvdOk);
 	dev->stats.collisions += dr32(SingleColFrames)
 			     +  dr32(MultiColFrames);
 

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Horatiu Vultur <[email protected]>

[ Upstream commit 882e57cbc7204662f6c5672d5b04336c1d790b03 ]

It looks like that every time when the interface was set down and up the driver was creating a new ptp clock. On top of this the function ptp_clock_unregister was never called.
Therefore fix this by calling ptp_clock_register and initialize the mii_ts struct inside the probe function and call ptp_clock_unregister when driver is removed.

---
 drivers/net/phy/mscc/mscc.h      |  4 ++++
 drivers/net/phy/mscc/mscc_main.c |  4 +---
 drivers/net/phy/mscc/mscc_ptp.c  | 34 ++++++++++++++++++++------------
 3 files changed, 26 insertions(+), 16 deletions(-)

index 878298304430c..fcfbff691b3c6 100644
@@ -474,6 +474,7 @@ static inline void vsc8584_config_macsec_intr(struct phy_device *phydev)
 void vsc85xx_link_change_notify(struct phy_device *phydev);
 void vsc8584_config_ts_intr(struct phy_device *phydev);
 int vsc8584_ptp_init(struct phy_device *phydev);
+void vsc8584_ptp_deinit(struct phy_device *phydev);
 int vsc8584_ptp_probe_once(struct phy_device *phydev);
 int vsc8584_ptp_probe(struct phy_device *phydev);
 irqreturn_t vsc8584_handle_ts_interrupt(struct phy_device *phydev);

@@ -488,6 +489,9 @@ static inline int vsc8584_ptp_init(struct phy_device *phydev)
 {
 	return 0;
 }
+static inline void vsc8584_ptp_deinit(struct phy_device *phydev)
+{
+}
 static inline int vsc8584_ptp_probe_once(struct phy_device *phydev)
 {
 	return 0;

index 03aa85ec60dfc..982e73adf2bcf 100644
@@ -2326,9 +2326,7 @@ static int vsc85xx_probe(struct phy_device *phydev)
 
 static void vsc85xx_remove(struct phy_device *phydev)
 {
-	struct vsc8531_private *priv = phydev->priv;
-
-	skb_queue_purge(&priv->rx_skbs_list);
+	vsc8584_ptp_deinit(phydev);
 }
 
 /* Microsemi VSC85xx PHYs */

index f77bfbee5f20b..e30e6ba9da2f4 100644
@@ -1294,7 +1294,6 @@ static void vsc8584_set_input_clk_configured(struct phy_device *phydev)
 
 static int __vsc8584_init_ptp(struct phy_device *phydev)
 {
-	struct vsc8531_private *vsc8531 = phydev->priv;
 	static const u32 ltc_seq_e[] = { 0, 400000, 0, 0, 0 };
 	static const u8  ltc_seq_a[] = { 8, 6, 5, 4, 2 };
 	u32 val;

@@ -1511,17 +1510,7 @@ static int __vsc8584_init_ptp(struct phy_device *phydev)
 
 	vsc85xx_ts_eth_cmp1_sig(phydev);
 
-	vsc8531->mii_ts.rxtstamp = vsc85xx_rxtstamp;
-	vsc8531->mii_ts.txtstamp = vsc85xx_txtstamp;
-	vsc8531->mii_ts.hwtstamp = vsc85xx_hwtstamp;
-	vsc8531->mii_ts.ts_info  = vsc85xx_ts_info;
-	phydev->mii_ts = &vsc8531->mii_ts;
-
-	memcpy(&vsc8531->ptp->caps, &vsc85xx_clk_caps, sizeof(vsc85xx_clk_caps));
-
-	vsc8531->ptp->ptp_clock = ptp_clock_register(&vsc8531->ptp->caps,
-						     &phydev->mdio.dev);
-	return PTR_ERR_OR_ZERO(vsc8531->ptp->ptp_clock);
+	return 0;
 }
 
 void vsc8584_config_ts_intr(struct phy_device *phydev)

@@ -1548,6 +1537,16 @@ int vsc8584_ptp_init(struct phy_device *phydev)
 	return 0;
 }
 
+void vsc8584_ptp_deinit(struct phy_device *phydev)
+{
+	struct vsc8531_private *vsc8531 = phydev->priv;
+
+	if (vsc8531->ptp->ptp_clock) {
+		ptp_clock_unregister(vsc8531->ptp->ptp_clock);
+		skb_queue_purge(&vsc8531->rx_skbs_list);
+	}
+}
+
 irqreturn_t vsc8584_handle_ts_interrupt(struct phy_device *phydev)
 {
 	struct vsc8531_private *priv = phydev->priv;

@@ -1605,7 +1604,16 @@ int vsc8584_ptp_probe(struct phy_device *phydev)
 
 	vsc8531->ptp->phydev = phydev;
 
-	return 0;
+	vsc8531->mii_ts.rxtstamp = vsc85xx_rxtstamp;
+	vsc8531->mii_ts.txtstamp = vsc85xx_txtstamp;
+	vsc8531->mii_ts.hwtstamp = vsc85xx_hwtstamp;
+	vsc8531->mii_ts.ts_info  = vsc85xx_ts_info;
+	phydev->mii_ts = &vsc8531->mii_ts;
+
+	memcpy(&vsc8531->ptp->caps, &vsc85xx_clk_caps, sizeof(vsc85xx_clk_caps));
+	vsc8531->ptp->ptp_clock = ptp_clock_register(&vsc8531->ptp->caps,
+						     &phydev->mdio.dev);
+	return PTR_ERR_OR_ZERO(vsc8531->ptp->ptp_clock);
 }
 
 int vsc8584_ptp_probe_once(struct phy_device *phydev)

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alexei Lazar <[email protected]>

[ Upstream commit ceddedc969f0532b7c62ca971ee50d519d2bc0cb ]

Xon/Xoff sizes are derived from calculation that include the MTU size. Set Xon/Xoff when MTU is set.
If Xon/Xoff fails, set the previous MTU.

---
 .../mellanox/mlx5/core/en/port_buffer.h         | 12 ++++++++++++
 .../net/ethernet/mellanox/mlx5/core/en_main.c   | 17 ++++++++++++++++-
 2 files changed, 28 insertions(+), 1 deletion(-)

index 80af7a5ac6046..a23e3d810f3e4 100644
@@ -63,11 +63,23 @@ struct mlx5e_port_buffer {
 	struct mlx5e_bufferx_reg  buffer[MLX5E_MAX_BUFFER];
 };
 
+#ifdef CONFIG_MLX5_CORE_EN_DCB
 int mlx5e_port_manual_buffer_config(struct mlx5e_priv *priv,
 				    u32 change, unsigned int mtu,
 				    struct ieee_pfc *pfc,
 				    u32 *buffer_size,
 				    u8 *prio2buffer);
+#else
+static inline int
+mlx5e_port_manual_buffer_config(struct mlx5e_priv *priv,
+				u32 change, unsigned int mtu,
+				void *pfc,
+				u32 *buffer_size,
+				u8 *prio2buffer)
+{
+	return 0;
+}
+#endif
 
 int mlx5e_port_query_buffer(struct mlx5e_priv *priv,
 			    struct mlx5e_port_buffer *port_buffer);

index 321441e6ad328..bb7e3c80ad74e 100644
@@ -42,6 +42,7 @@
 #include "eswitch.h"
 #include "en.h"
 #include "en/txrx.h"
+#include "en/port_buffer.h"
 #include "en_tc.h"
 #include "en_rep.h"
 #include "en_accel/ipsec.h"

@@ -2242,9 +2243,11 @@ int mlx5e_set_dev_port_mtu(struct mlx5e_priv *priv)
 	struct mlx5e_params *params = &priv->channels.params;
 	struct net_device *netdev = priv->netdev;
 	struct mlx5_core_dev *mdev = priv->mdev;
-	u16 mtu;
+	u16 mtu, prev_mtu;
 	int err;
 
+	mlx5e_query_mtu(mdev, params, &prev_mtu);
+
 	err = mlx5e_set_mtu(mdev, params, params->sw_mtu);
 	if (err)
 		return err;

@@ -2254,6 +2257,18 @@ int mlx5e_set_dev_port_mtu(struct mlx5e_priv *priv)
 		netdev_warn(netdev, "%s: VPort MTU %d is different than netdev mtu %d\n",
 			    __func__, mtu, params->sw_mtu);
 
+	if (mtu != prev_mtu && MLX5_BUFFER_SUPPORTED(mdev)) {
+		err = mlx5e_port_manual_buffer_config(priv, 0, mtu,
+						      NULL, NULL, NULL);
+		if (err) {
+			netdev_warn(netdev, "%s: Failed to set Xon/Xoff values with MTU %d (err %d), setting back to previous MTU %d\n",
+				    __func__, mtu, err, prev_mtu);
+
+			mlx5e_set_mtu(mdev, params, prev_mtu);
+			return err;
+		}
+	}
+
 	params->sw_mtu = mtu;
 	return 0;
 }

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alexei Lazar <[email protected]>

[ Upstream commit d24341740fe48add8a227a753e68b6eedf4b385a ]

Xon/Xoff sizes are derived from calculations that include the port speed.
These settings need to be updated and applied whenever the port speed is changed.
The port speed is typically set after the physical link goes down and is negotiated as part of the link-up process between the two connected interfaces.
Xon/Xoff parameters being updated at the point where the new negotiated speed is established.

---
 drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 2 ++
 1 file changed, 2 insertions(+)

index bb7e3c80ad74e..cfbc569edfb5f 100644
@@ -104,6 +104,8 @@ void mlx5e_update_carrier(struct mlx5e_priv *priv)
 	if (up) {
 		netdev_info(priv->netdev, "Link up\n");
 		netif_carrier_on(priv->netdev);
+		mlx5e_port_manual_buffer_config(priv, 0, priv->netdev->mtu,
+						NULL, NULL, NULL);
 	} else {
 		netdev_info(priv->netdev, "Link down\n");
 		netif_carrier_off(priv->netdev);

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alexei Lazar <[email protected]>

[ Upstream commit aca0c31af61e0d5cf1675a0cbd29460b95ae693c ]

The local Xoff value is being set before the firmware (FW) update. In case of a failure where the FW is not updated with the new value, there is no fallback to the previous value.
Update the local Xoff value after the FW has been successfully set.

---
 drivers/net/ethernet/mellanox/mlx5/core/en/port_buffer.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

index c9d5d8d93994d..7899a7230299d 100644
@@ -346,7 +346,6 @@ int mlx5e_port_manual_buffer_config(struct mlx5e_priv *priv,
 		if (err)
 			return err;
 	}
-	priv->dcbx.xoff = xoff;
 
 	/* Apply the settings */
 	if (update_buffer) {

@@ -355,6 +354,8 @@ int mlx5e_port_manual_buffer_config(struct mlx5e_priv *priv,
 			return err;
 	}
 
+	priv->dcbx.xoff = xoff;
+
 	if (update_prio2buffer)
 		err = mlx5e_port_set_priority2buffer(priv->mdev, prio2buffer);
 

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Rohan G Thomas <[email protected]>

[ Upstream commit 4f23382841e67174211271a454811dd17c0ef3c5 ]

Enabling RX FIFO Overflow interrupts is counterproductive and causes an interrupt storm when RX FIFO overflows. Disabling this interrupt has no side effect and eliminates interrupt storms when the RX FIFO overflows.

Commit 8a7cb245cf28 ("net: stmmac: Do not enable RX FIFO overflow interrupts") disables RX FIFO overflow interrupts for DWMAC4 IP and removes the corresponding handling of this interrupt. This patch is doing the same thing for XGMAC IP.

---
 drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c | 4 ----
 1 file changed, 4 deletions(-)

index 5e98355f422b3..3e4318d5dcdf5 100644
@@ -199,10 +199,6 @@ static void dwxgmac2_dma_rx_mode(void __iomem *ioaddr, int mode,
 	}
 
 	writel(value, ioaddr + XGMAC_MTL_RXQ_OPMODE(channel));
-
-	/* Enable MTL RX overflow */
-	value = readl(ioaddr + XGMAC_MTL_QINTEN(channel));
-	writel(value | XGMAC_RXOIE, ioaddr + XGMAC_MTL_QINTEN(channel));
 }
 
 static void dwxgmac2_dma_tx_mode(void __iomem *ioaddr, int mode,

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Eric Dumazet <[email protected]>

[ Upstream commit 2e8750469242cad8f01f320131fd5a6f540dbb99 ]

syzbot found that sin6_scope_id was not properly initialized, leading to undefined behavior.

Clear sin6_scope_id and sin6_flowinfo.

BUG: KMSAN: uninit-value in __sctp_v6_cmp_addr+0x887/0x8c0 net/sctp/ipv6.c:649
  __sctp_v6_cmp_addr+0x887/0x8c0 net/sctp/ipv6.c:649
  sctp_inet6_cmp_addr+0x4f2/0x510 net/sctp/ipv6.c:983
  sctp_bind_addr_conflict+0x22a/0x3b0 net/sctp/bind_addr.c:390
  sctp_get_port_local+0x21eb/0x2440 net/sctp/socket.c:8452
  sctp_get_port net/sctp/socket.c:8523 [inline]
  sctp_listen_start net/sctp/socket.c:8567 [inline]
  sctp_inet_listen+0x710/0xfd0 net/sctp/socket.c:8636
  __sys_listen_socket net/socket.c:1912 [inline]
  __sys_listen net/socket.c:1927 [inline]
  __do_sys_listen net/socket.c:1932 [inline]
  __se_sys_listen net/socket.c:1930 [inline]
  __x64_sys_listen+0x343/0x4c0 net/socket.c:1930
  x64_sys_call+0x271d/0x3e20 arch/x86/include/generated/asm/syscalls_64.h:51
  do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
  do_syscall_64+0xd9/0x210 arch/x86/entry/syscall_64.c:94
 entry_SYSCALL_64_after_hwframe+0x77/0x7f

Local variable addr.i.i created at:

  sctp_get_port net/sctp/socket.c:8515 [inline]
  sctp_listen_start net/sctp/socket.c:8567 [inline]
  sctp_inet_listen+0x650/0xfd0 net/sctp/socket.c:8636
  __sys_listen_socket net/socket.c:1912 [inline]
  __sys_listen net/socket.c:1927 [inline]
  __do_sys_listen net/socket.c:1932 [inline]
  __se_sys_listen net/socket.c:1930 [inline]
  __x64_sys_listen+0x343/0x4c0 net/socket.c:1930

---
 net/sctp/ipv6.c | 2 ++
 1 file changed, 2 insertions(+)

index 470dbdc27d584..107255d92037f 100644
@@ -547,7 +547,9 @@ static void sctp_v6_from_sk(union sctp_addr *addr, struct sock *sk)
 {
 	addr->v6.sin6_family = AF_INET6;
 	addr->v6.sin6_port = 0;
+	addr->v6.sin6_flowinfo = 0;
 	addr->v6.sin6_addr = sk->sk_v6_rcv_saddr;
+	addr->v6.sin6_scope_id = 0;
 }
 
 /* Initialize sk->sk_rcv_saddr from sctp_addr. */

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Li Nan <[email protected]>

[ Upstream commit a6358f8cf64850f3f27857b8ed8c1b08cfc4685c ]

Observed on kernel 6.6 (present on master as well):

  BUG: KASAN: slab-out-of-bounds in memcmp+0x98/0xd0
  Call trace:
   kasan_check_range+0xe8/0x190
   __asan_loadN+0x1c/0x28
   memcmp+0x98/0xd0
   efivarfs_d_compare+0x68/0xd8
   __d_lookup_rcu_op_compare+0x178/0x218
   __d_lookup_rcu+0x1f8/0x228
   d_alloc_parallel+0x150/0x648
   lookup_open.isra.0+0x5f0/0x8d0
   open_last_lookups+0x264/0x828
   path_openat+0x130/0x3f8
   do_filp_open+0x114/0x248
   do_sys_openat2+0x340/0x3c0
   __arm64_sys_openat+0x120/0x1a0

If dentry->d_name.len < EFI_VARIABLE_GUID_LEN , 'guid' can become negative, leadings to oob. The issue can be triggered by parallel lookups using invalid filename:

T1 T2
lookup_open
->lookup

    simple_lookup
     d_add
     // invalid dentry is added to hash list

			lookup_open
			 d_alloc_parallel
			  __d_lookup_rcu
			   __d_lookup_rcu_op_compare
			    hlist_bl_for_each_entry_rcu
			    // invalid dentry can be retrieved
			     ->d_compare
			      efivarfs_d_compare
			      // oob

Fix it by checking 'guid' before cmp.

---
 fs/efivarfs/super.c | 4 ++++
 1 file changed, 4 insertions(+)

index 99d002438008b..124db520b2bd6 100644
@@ -47,6 +47,10 @@ static int efivarfs_d_compare(const struct dentry *dentry,
 {
 	int guid = len - EFI_VARIABLE_GUID_LEN;
 
+	/* Parallel lookups may produce a temporary invalid filename */
+	if (guid <= 0)
+		return 1;
+
 	if (name->len != len)
 		return 1;
 

2.50.1

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Thijs Raymakers <[email protected]>

commit c87bd4dd43a624109c3cc42d843138378a7f4548 upstream.

min and dest_id are guest-controlled indices. Using array_index_nospec() after the bounds checks clamps these values to mitigate speculative execution side-channels.

---
 arch/x86/kvm/lapic.c |    2 ++
 arch/x86/kvm/x86.c   |    7 +++++--
 2 files changed, 7 insertions(+), 2 deletions(-)

@@ -613,6 +613,8 @@ static int __pv_send_ipi(unsigned long *
 	if (min > map->max_apic_id)
 		return 0;
 
+	min = array_index_nospec(min, map->max_apic_id + 1);
+
 	for_each_set_bit(i, ipi_bitmap,
 		min((u32)BITS_PER_LONG, (map->max_apic_id - min + 1))) {
 		if (map->phys_map[min + i]) {

@@ -8923,8 +8923,11 @@ static void kvm_sched_yield(struct kvm_v
 	rcu_read_lock();
 	map = rcu_dereference(vcpu->kvm->arch.apic_map);
 
-	if (likely(map) && dest_id <= map->max_apic_id && map->phys_map[dest_id])
-		target = map->phys_map[dest_id]->vcpu;
+	if (likely(map) && dest_id <= map->max_apic_id) {
+		dest_id = array_index_nospec(dest_id, map->max_apic_id + 1);
+		if (map->phys_map[dest_id])
+			target = map->phys_map[dest_id]->vcpu;
+	}
 
 	rcu_read_unlock();
 

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Qasim Ijaz <[email protected]>

commit d3af6ca9a8c34bbd8cff32b469b84c9021c9e7e4 upstream.

After hid_hw_start() is called hidinput_connect() will eventually be called to set up the device with the input layer since the HID_CONNECT_DEFAULT connect mask is used. During hidinput_connect() all input and output reports are processed and corresponding hid_inputs are allocated and configured via hidinput_configure_usages(). This process involves slot tagging report fields and configuring usages by setting relevant bits in the capability bitmaps. However it is possible that the capability bitmaps are not set at all leading to the subsequent hidinput_has_been_populated() check to fail leading to the freeing of the hid_input and the underlying input device.

This becomes problematic because a malicious HID device like a ASUS ROG N-Key keyboard can trigger the above scenario via a specially crafted descriptor which then leads to a user-after-free when the name of the freed input device is written to later on after hid_hw_start(). Below, report 93 intentionally utilises the HID_UP_UNDEFINED Usage Page which is skipped during usage configuration, leading to the frees.

0x05, 0x0D,        // Usage Page (Digitizer)
0x09, 0x05,        // Usage (Touch Pad)
0xA1, 0x01,        // Collection (Application)
0x85, 0x0D,        //   Report ID (13)
0x06, 0x00, 0xFF,  //   Usage Page (Vendor Defined 0xFF00)
0x09, 0xC5,        //   Usage (0xC5)
0x15, 0x00,        //   Logical Minimum (0)
0x26, 0xFF, 0x00,  //   Logical Maximum (255)
0x75, 0x08,        //   Report Size (8)
0x95, 0x04,        //   Report Count (4)
0xB1, 0x02,        //   Feature (Data,Var,Abs)
0x85, 0x5D,        //   Report ID (93)
0x06, 0x00, 0x00,  //   Usage Page (Undefined)
0x09, 0x01,        //   Usage (0x01)
0x15, 0x00,        //   Logical Minimum (0)
0x26, 0xFF, 0x00,  //   Logical Maximum (255)
0x75, 0x08,        //   Report Size (8)
0x95, 0x1B,        //   Report Count (27)
0x81, 0x02,        //   Input (Data,Var,Abs)
0xC0,              // End Collection

Below is the KASAN splat after triggering the UAF:

[   21.672709] ==================================================================
[   21.673700] BUG: KASAN: slab-use-after-free in asus_probe+0xeeb/0xf80
[   21.673700] Write of size 8 at addr ffff88810a0ac000 by task kworker/1:2/54
[   21.673700]
[   21.673700] CPU: 1 UID: 0 PID: 54 Comm: kworker/1:2 Not tainted 6.16.0-rc4-g9773391cf4dd-dirty #36 PREEMPT(voluntary)
[   21.673700] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014
[   21.673700] Call Trace:
[   21.673700]  <TASK>
[   21.673700]  dump_stack_lvl+0x5f/0x80
[   21.673700]  print_report+0xd1/0x660
[   21.673700]  kasan_report+0xe5/0x120
[   21.673700]  __asan_report_store8_noabort+0x1b/0x30
[   21.673700]  asus_probe+0xeeb/0xf80
[   21.673700]  hid_device_probe+0x2ee/0x700
[   21.673700]  really_probe+0x1c6/0x6b0
[   21.673700]  __driver_probe_device+0x24f/0x310
[   21.673700]  driver_probe_device+0x4e/0x220
[...]
[   21.673700]
[   21.673700] Allocated by task 54:
[   21.673700]  kasan_save_stack+0x3d/0x60
[   21.673700]  kasan_save_track+0x18/0x40
[   21.673700]  kasan_save_alloc_info+0x3b/0x50
[   21.673700]  __kasan_kmalloc+0x9c/0xa0
[   21.673700]  __kmalloc_cache_noprof+0x139/0x340
[   21.673700]  input_allocate_device+0x44/0x370
[   21.673700]  hidinput_connect+0xcb6/0x2630
[   21.673700]  hid_connect+0xf74/0x1d60
[   21.673700]  hid_hw_start+0x8c/0x110
[   21.673700]  asus_probe+0x5a3/0xf80
[   21.673700]  hid_device_probe+0x2ee/0x700
[   21.673700]  really_probe+0x1c6/0x6b0
[   21.673700]  __driver_probe_device+0x24f/0x310
[   21.673700]  driver_probe_device+0x4e/0x220
[...]
[   21.673700]
[   21.673700] Freed by task 54:
[   21.673700]  kasan_save_stack+0x3d/0x60
[   21.673700]  kasan_save_track+0x18/0x40
[   21.673700]  kasan_save_free_info+0x3f/0x60
[   21.673700]  __kasan_slab_free+0x3c/0x50
[   21.673700]  kfree+0xcf/0x350
[   21.673700]  input_dev_release+0xab/0xd0
[   21.673700]  device_release+0x9f/0x220
[   21.673700]  kobject_put+0x12b/0x220
[   21.673700]  put_device+0x12/0x20
[   21.673700]  input_free_device+0x4c/0xb0
[   21.673700]  hidinput_connect+0x1862/0x2630
[   21.673700]  hid_connect+0xf74/0x1d60
[   21.673700]  hid_hw_start+0x8c/0x110
[   21.673700]  asus_probe+0x5a3/0xf80
[   21.673700]  hid_device_probe+0x2ee/0x700
[   21.673700]  really_probe+0x1c6/0x6b0
[   21.673700]  __driver_probe_device+0x24f/0x310
[   21.673700]  driver_probe_device+0x4e/0x220

[...]

---
 drivers/hid/hid-asus.c |    8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

@@ -1135,7 +1135,13 @@ static int asus_probe(struct hid_device
 		return ret;
 	}
 
-	if (!drvdata->input) {
+	/*
+	 * Check that input registration succeeded. Checking that
+	 * HID_CLAIMED_INPUT is set prevents a UAF when all input devices
+	 * were freed during registration due to no usages being mapped,
+	 * leaving drvdata->input pointing to freed memory.
+	 */
+	if (!drvdata->input || !(hdev->claimed & HID_CLAIMED_INPUT)) {
 		hid_err(hdev, "Asus input not registered\n");
 		ret = -ENOMEM;
 		goto err_stop_hw;

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Qasim Ijaz <[email protected]>

commit 0379eb8691b9c4477da0277ae0832036ca4410b4 upstream.

A malicious HID device can trigger a slab out-of-bounds during mt_report_fixup() by passing in report descriptor smaller than 607 bytes. mt_report_fixup() attempts to patch byte offset 607 of the descriptor with 0x25 by first checking if byte offset 607 is 0x15 however it lacks bounds checks to verify if the descriptor is big enough before conducting this check. Fix this bug by ensuring the descriptor size is at least 608 bytes before accessing it.

Below is the KASAN splat after the out of bounds access happens:

[   13.671954] ==================================================================
[   13.672667] BUG: KASAN: slab-out-of-bounds in mt_report_fixup+0x103/0x110
[   13.673297] Read of size 1 at addr ffff888103df39df by task kworker/0:1/10
[   13.673297]
[   13.673297] CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Not tainted 6.15.0-00005-gec5d573d83f4-dirty #3
[   13.673297] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/04
[   13.673297] Call Trace:
[   13.673297]  <TASK>
[   13.673297]  dump_stack_lvl+0x5f/0x80
[   13.673297]  print_report+0xd1/0x660
[   13.673297]  kasan_report+0xe5/0x120
[   13.673297]  __asan_report_load1_noabort+0x18/0x20
[   13.673297]  mt_report_fixup+0x103/0x110
[   13.673297]  hid_open_report+0x1ef/0x810
[   13.673297]  mt_probe+0x422/0x960
[   13.673297]  hid_device_probe+0x2e2/0x6f0
[   13.673297]  really_probe+0x1c6/0x6b0
[   13.673297]  __driver_probe_device+0x24f/0x310
[   13.673297]  driver_probe_device+0x4e/0x220
[   13.673297]  __device_attach_driver+0x169/0x320
[   13.673297]  bus_for_each_drv+0x11d/0x1b0
[   13.673297]  __device_attach+0x1b8/0x3e0
[   13.673297]  device_initial_probe+0x12/0x20
[   13.673297]  bus_probe_device+0x13d/0x180
[   13.673297]  device_add+0xe3a/0x1670
[   13.673297]  hid_add_device+0x31d/0xa40

[...]

---
 drivers/hid/hid-multitouch.c |    8 ++++++++
 1 file changed, 8 insertions(+)

@@ -1448,6 +1448,14 @@ static __u8 *mt_report_fixup(struct hid_
 	if (hdev->vendor == I2C_VENDOR_ID_GOODIX &&
 	    (hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||
 	     hdev->product == I2C_DEVICE_ID_GOODIX_01E9)) {
+		if (*size < 608) {
+			dev_info(
+				&hdev->dev,
+				"GT7868Q fixup: report descriptor is only %u bytes, skipping\n",
+				*size);
+			return rdesc;
+		}
+
 		if (rdesc[607] == 0x15) {
 			rdesc[607] = 0x25;
 			dev_info(

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Ping Cheng <[email protected]>

commit 9fc51941d9e7793da969b2c66e6f8213c5b1237f upstream.

---
 drivers/hid/wacom_wac.c |    1 +
 1 file changed, 1 insertion(+)

@@ -684,6 +684,7 @@ static bool wacom_is_art_pen(int tool_id
 	case 0x885:	/* Intuos3 Marker Pen */
 	case 0x804:	/* Intuos4/5 13HD/24HD Marker Pen */
 	case 0x10804:	/* Intuos4/5 13HD/24HD Art Pen */
+	case 0x204:     /* Art Pen 2 */
 		is_art_pen = true;
 		break;
 	}

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Minjong Kim <[email protected]>

commit 185c926283da67a72df20a63a5046b3b4631b7d9 upstream.

in ntrig_report_version(), hdev parameter passed from hid_probe(). sending descriptor to /dev/uhid can make hdev->dev.parent->parent to null if hdev->dev.parent->parent is null, usb_dev has
invalid address(0xffffffffffffff58) that hid_to_usb_dev(hdev) returned when usb_rcvctrlpipe() use usb_dev,it trigger
page fault error for address(0xffffffffffffff58)

add null check logic to ntrig_report_version()
before calling hid_to_usb_dev()

---
 drivers/hid/hid-ntrig.c |    3 +++
 1 file changed, 3 insertions(+)

@@ -144,6 +144,9 @@ static void ntrig_report_version(struct
 	struct usb_device *usb_dev = hid_to_usb_dev(hdev);
 	unsigned char *data = kmalloc(8, GFP_KERNEL);
 
+	if (!hid_is_usb(hdev))
+		return;
+
 	if (!data)
 		goto err_free;
 

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alex Deucher <[email protected]>

commit ac4ed2da4c1305a1a002415058aa7deaf49ffe3e upstream.

This reverts commit b08425fa77ad2f305fe57a33dceb456be03b653f.

Revert this to align with 6.17 because the fixes tag was wrong on this commit.

---
 drivers/gpu/drm/amd/amdgpu/amdgpu_csa.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

@@ -93,8 +93,8 @@ int amdgpu_map_static_csa(struct amdgpu_
 	}
 
 	r = amdgpu_vm_bo_map(adev, *bo_va, csa_addr, 0, size,
-			     AMDGPU_VM_PAGE_READABLE | AMDGPU_VM_PAGE_WRITEABLE |
-			     AMDGPU_VM_PAGE_EXECUTABLE);
+			     AMDGPU_PTE_READABLE | AMDGPU_PTE_WRITEABLE |
+			     AMDGPU_PTE_EXECUTABLE);
 
 	if (r) {
 		DRM_ERROR("failed to do bo_map on static CSA, err=%d\n", r);

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Shanker Donthineni <[email protected]>

commit 89a2d212bdb4bc29bed8e7077abe054b801137ea upstream.

When CONFIG_DMA_DIRECT_REMAP is enabled, atomic pool pages are remapped via dma_common_contiguous_remap() using the supplied pgprot. Currently, the mapping uses pgprot_dmacoherent(PAGE_KERNEL), which leaves the memory encrypted on systems with memory encryption enabled (e.g., ARM CCA Realms).

This can cause the DMA layer to fail or crash when accessing the memory, as the underlying physical pages are not configured as expected.

Fix this by requesting a decrypted mapping in the vmap() call:
pgprot_decrypted(pgprot_dmacoherent(PAGE_KERNEL))

This ensures that atomic pool memory is consistently mapped unencrypted.

---
 kernel/dma/pool.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

@@ -102,8 +102,8 @@ static int atomic_pool_expand(struct gen
 
 #ifdef CONFIG_DMA_DIRECT_REMAP
 	addr = dma_common_contiguous_remap(page, pool_size,
-					   pgprot_dmacoherent(PAGE_KERNEL),
-					   __builtin_return_address(0));
+			pgprot_decrypted(pgprot_dmacoherent(PAGE_KERNEL)),
+			__builtin_return_address(0));
 	if (!addr)
 		goto free_page;
 #else

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Fabio Porcedda <[email protected]>

commit e81a7f65288c7e2cfb7e7890f648e099fd885ab3 upstream.

Add the following Telit Cinterion LE910C4-WWX new compositions:

0x1034: tty (AT) + tty (AT) + rmnet

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  8 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=1034 Rev=00.00
S:  Manufacturer=Telit
S:  Product=LE910C4-WWX
S:  SerialNumber=93f617e7
C:  #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

0x1037: tty (diag) + tty (Telit custom) + tty (AT) + tty (AT) + rmnet

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 15 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=1037 Rev=00.00
S:  Manufacturer=Telit
S:  Product=LE910C4-WWX
S:  SerialNumber=93f617e7
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

0x1038: tty (Telit custom) + tty (AT) + tty (AT) + rmnet

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  9 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=1038 Rev=00.00
S:  Manufacturer=Telit
S:  Product=LE910C4-WWX
S:  SerialNumber=93f617e7
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

---
 drivers/net/usb/qmi_wwan.c |    3 +++
 1 file changed, 3 insertions(+)

@@ -1358,6 +1358,9 @@ static const struct usb_device_id produc
 	{QMI_FIXED_INTF(0x2357, 0x0201, 4)},	/* TP-LINK HSUPA Modem MA180 */
 	{QMI_FIXED_INTF(0x2357, 0x9000, 4)},	/* TP-LINK MA260 */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1031, 3)}, /* Telit LE910C1-EUX */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1034, 2)}, /* Telit LE910C4-WWX */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1037, 4)}, /* Telit LE910C4-WWX */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1038, 3)}, /* Telit LE910C4-WWX */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x103a, 0)}, /* Telit LE910C4-WWX */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1040, 2)},	/* Telit LE922A */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1050, 2)},	/* Telit FN980 */

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: James Jones <[email protected]>

commit e2fe0c54fb7401e6ecd3c10348519ab9e23bd639 upstream.

On some chipsets, which block-linear modifiers are supported is format-specific. However, linear modifiers are always be supported. The prior modifier filtering logic was not accounting for the linear case.

---
 drivers/gpu/drm/nouveau/dispnv50/wndw.c |    4 ++++
 1 file changed, 4 insertions(+)

@@ -664,6 +664,10 @@ static bool nv50_plane_format_mod_suppor
 	struct nouveau_drm *drm = nouveau_drm(plane->dev);
 	uint8_t i;
 
+	/* All chipsets can display all formats in linear layout */
+	if (modifier == DRM_FORMAT_MOD_LINEAR)
+		return true;
+
 	if (drm->client.device.info.chipset < 0xc0) {
 		const struct drm_format_info *info = drm_format_info(format);
 		const uint8_t kind = (modifier >> 12) & 0xff;

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Hamish Martin <[email protected]>

commit 02a46753601a24e1673d9c28173121055e8e6cc9 upstream.

Since the initial commit of this driver the I2C bus speed has been reconfigured for every single transfer. This is despite the fact that we never change the speed and it is never "lost" by the chip. Upon investigation we find that what was really happening was that the setting of the bus speed had the side effect of cancelling a previous failed command if there was one, thereby freeing the bus. This is the part that was actually required to keep the bus operational in the face of failed commands.

Instead of always setting the speed, we now correctly cancel any failed commands as they are detected. This means we can just set the bus speed at probe time and remove the previous speed sets on each transfer. This has the effect of improving performance and reducing the number of commands required to complete transfers.

---
 drivers/hid/hid-mcp2221.c |   41 +++++++++++++++++++++++++++--------------
 1 file changed, 27 insertions(+), 14 deletions(-)

@@ -169,6 +169,25 @@ static int mcp_cancel_last_cmd(struct mc
 	return mcp_send_data_req_status(mcp, mcp->txbuf, 8);
 }
 
+/* Check if the last command succeeded or failed and return the result.
+ * If the command did fail, cancel that command which will free the i2c bus.
+ */
+static int mcp_chk_last_cmd_status_free_bus(struct mcp2221 *mcp)
+{
+	int ret;
+
+	ret = mcp_chk_last_cmd_status(mcp);
+	if (ret) {
+		/* The last command was a failure.
+		 * Send a cancel which will also free the bus.
+		 */
+		usleep_range(980, 1000);
+		mcp_cancel_last_cmd(mcp);
+	}
+
+	return ret;
+}
+
 static int mcp_set_i2c_speed(struct mcp2221 *mcp)
 {
 	int ret;

@@ -223,7 +242,7 @@ static int mcp_i2c_write(struct mcp2221
 		usleep_range(980, 1000);
 
 		if (last_status) {
-			ret = mcp_chk_last_cmd_status(mcp);
+			ret = mcp_chk_last_cmd_status_free_bus(mcp);
 			if (ret)
 				return ret;
 		}

@@ -290,7 +309,7 @@ static int mcp_i2c_smbus_read(struct mcp
 		if (ret)
 			return ret;
 
-		ret = mcp_chk_last_cmd_status(mcp);
+		ret = mcp_chk_last_cmd_status_free_bus(mcp);
 		if (ret)
 			return ret;
 

@@ -310,11 +329,6 @@ static int mcp_i2c_xfer(struct i2c_adapt
 
 	mutex_lock(&mcp->lock);
 
-	/* Setting speed before every transaction is required for mcp2221 */
-	ret = mcp_set_i2c_speed(mcp);
-	if (ret)
-		goto exit;
-
 	if (num == 1) {
 		if (msgs->flags & I2C_M_RD) {
 			ret = mcp_i2c_smbus_read(mcp, msgs, MCP2221_I2C_RD_DATA,

@@ -399,9 +413,7 @@ static int mcp_smbus_write(struct mcp222
 	if (last_status) {
 		usleep_range(980, 1000);
 
-		ret = mcp_chk_last_cmd_status(mcp);
-		if (ret)
-			return ret;
+		ret = mcp_chk_last_cmd_status_free_bus(mcp);
 	}
 
 	return ret;

@@ -419,10 +431,6 @@ static int mcp_smbus_xfer(struct i2c_ada
 
 	mutex_lock(&mcp->lock);
 
-	ret = mcp_set_i2c_speed(mcp);
-	if (ret)
-		goto exit;
-
 	switch (size) {
 
 	case I2C_SMBUS_QUICK:

@@ -870,6 +878,11 @@ static int mcp2221_probe(struct hid_devi
 	if (i2c_clk_freq < 50)
 		i2c_clk_freq = 50;
 	mcp->cur_i2c_clk_div = (12000000 / (i2c_clk_freq * 1000)) - 3;
+	ret = mcp_set_i2c_speed(mcp);
+	if (ret) {
+		hid_err(hdev, "can't set i2c speed: %d\n", ret);
+		return ret;
+	}
 
 	mcp->adapter.owner = THIS_MODULE;
 	mcp->adapter.class = I2C_CLASS_HWMON;

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Hamish Martin <[email protected]>

commit 2682468671aa0b4d52ae09779b48212a80d71b91 upstream.

When a user requests more than 60 bytes of data the MCP2221 must chunk the data in chunks up to 60 bytes long (see command/response code 0x40 in the datasheet).
In order to signal that the device has more data the (undocumented) byte at byte index 2 of the Get I2C Data response uses the value 0x54. This contrasts with the case for the final data chunk where the value returned is 0x55 (MCP2221_I2C_READ_COMPL). The fact that 0x55 was not returned in the response was interpreted by the driver as a failure meaning that all reads of more than 60 bytes would fail.

Add support for reads that are split over multiple chunks by looking for the response code indicating that more data is expected and continuing the read as the code intended. Some timing delays are required to ensure the chip has time to refill its FIFO as data is read in from the I2C bus. This timing has been tested in my system when configured for bus speeds of 50KHz, 100KHz, and 400KHz and operates well.

---
 drivers/hid/hid-mcp2221.c |   32 +++++++++++++++++++++++---------
 1 file changed, 23 insertions(+), 9 deletions(-)

@@ -44,6 +44,7 @@ enum {
 	MCP2221_I2C_MASK_ADDR_NACK = 0x40,
 	MCP2221_I2C_WRADDRL_SEND = 0x21,
 	MCP2221_I2C_ADDR_NACK = 0x25,
+	MCP2221_I2C_READ_PARTIAL = 0x54,
 	MCP2221_I2C_READ_COMPL = 0x55,
 	MCP2221_ALT_F_NOT_GPIOV = 0xEE,
 	MCP2221_ALT_F_NOT_GPIOD = 0xEF,

@@ -279,6 +280,7 @@ static int mcp_i2c_smbus_read(struct mcp
 {
 	int ret;
 	u16 total_len;
+	int retries = 0;
 
 	mcp->txbuf[0] = type;
 	if (msg) {

@@ -302,20 +304,31 @@ static int mcp_i2c_smbus_read(struct mcp
 	mcp->rxbuf_idx = 0;
 
 	do {
+		/* Wait for the data to be read by the device */
+		usleep_range(980, 1000);
+
 		memset(mcp->txbuf, 0, 4);
 		mcp->txbuf[0] = MCP2221_I2C_GET_DATA;
 
 		ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1);
-		if (ret)
-			return ret;
-
-		ret = mcp_chk_last_cmd_status_free_bus(mcp);
-		if (ret)
-			return ret;
-
-		usleep_range(980, 1000);
+		if (ret) {
+			if (retries < 5) {
+				/* The data wasn't ready to read.
+				 * Wait a bit longer and try again.
+				 */
+				usleep_range(90, 100);
+				retries++;
+			} else {
+				return ret;
+			}
+		} else {
+			retries = 0;
+		}
 	} while (mcp->rxbuf_idx < total_len);
 
+	usleep_range(980, 1000);
+	ret = mcp_chk_last_cmd_status_free_bus(mcp);
+
 	return ret;
 }
 

@@ -776,7 +789,8 @@ static int mcp2221_raw_event(struct hid_
 				mcp->status = -EIO;
 				break;
 			}
-			if (data[2] == MCP2221_I2C_READ_COMPL) {
+			if (data[2] == MCP2221_I2C_READ_COMPL ||
+			    data[2] == MCP2221_I2C_READ_PARTIAL) {
 				buf = mcp->rxbuf;
 				memcpy(&buf[mcp->rxbuf_idx], &data[4], data[3]);
 				mcp->rxbuf_idx = mcp->rxbuf_idx + data[3];

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Imre Deak <[email protected]>

This reverts commit a19b31f854a8992dfa35255f43efd19be292b15c which is commit a40c5d727b8111b5db424a1e43e14a1dcce1e77f upstream.

The upstream commit a40c5d727b8111b5db424a1e43e14a1dcce1e77f ("drm/dp:
Change AUX DPCD probe address from DPCD_REV to LANE0_1_STATUS") the reverted commit backported causes a regression, on one eDP panel at least resulting in display flickering, described in detail at the Link:
below. The issue fixed by the upstream commit will need a different solution, revert the backport for now.

---
 drivers/gpu/drm/drm_dp_helper.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -336,7 +336,7 @@ ssize_t drm_dp_dpcd_read(struct drm_dp_a
 	 * monitor doesn't power down exactly after the throw away read.
 	 */
 	if (!aux->is_remote) {
-		ret = drm_dp_dpcd_access(aux, DP_AUX_NATIVE_READ, DP_LANE0_1_STATUS,
+		ret = drm_dp_dpcd_access(aux, DP_AUX_NATIVE_READ, DP_DPCD_REV,
 					 buffer, 1);
 		if (ret != 1)
 			goto out;

5.15-stable review patch. If anyone has any objections, please let me know.

------------------

From: Eric Sandeen <[email protected]>

commit ae668cd567a6a7622bc813ee0bb61c42bed61ba7 upstream.

ENODATA (aka ENOATTR) has a very specific meaning in the xfs xattr code; namely, that the requested attribute name could not be found.

However, a medium error from disk may also return ENODATA. At best, this medium error may escape to userspace as "attribute not found" when in fact it's an IO (disk) error.

At worst, we may oops in xfs_attr_leaf_get() when we do:

	error = xfs_attr_leaf_hasname(args, &bp);
	if (error == -ENOATTR)  {
		xfs_trans_brelse(args->trans, bp);
		return error;
	}

because an ENODATA/ENOATTR error from disk leaves us with a null bp, and the xfs_trans_brelse will then null-deref it.

As discussed on the list, we really need to modify the lower level IO functions to trap all disk errors and ensure that we don't let unique errors like this leak up into higher xfs functions - many like this should be remapped to EIO.

However, this patch directly addresses a reported bug in the xattr code, and should be safe to backport to stable kernels. A larger-scope patch to handle more unique errors at lower levels can follow later.

(Note, prior to 07120f1abdff we did not oops, but we did return the wrong error code to userspace.)

---
 fs/xfs/libxfs/xfs_attr_remote.c |    7 +++++++
 fs/xfs/libxfs/xfs_da_btree.c    |    6 ++++++
 2 files changed, 13 insertions(+)

@@ -418,6 +418,13 @@ xfs_attr_rmtval_get(
 			dblkcnt = XFS_FSB_TO_BB(mp, map[i].br_blockcount);
 			error = xfs_buf_read(mp->m_ddev_targp, dblkno, dblkcnt,
 					0, &bp, &xfs_attr3_rmt_buf_ops);
+			/*
+			 * ENODATA from disk implies a disk medium failure;
+			 * ENODATA for xattrs means attribute not found, so
+			 * disambiguate that here.
+			 */
+			if (error == -ENODATA)
+				error = -EIO;
 			if (error)
 				return error;
 

@@ -2639,6 +2639,12 @@ xfs_da_read_buf(
 
 	error = xfs_trans_read_buf_map(mp, tp, mp->m_ddev_targp, mapp, nmap, 0,
 			&bp, ops);
+	/*
+	 * ENODATA from disk implies a disk medium failure; ENODATA for
+	 * xattrs means attribute not found, so disambiguate that here.
+	 */
+	if (error == -ENODATA && whichfork == XFS_ATTR_FORK)
+		error = -EIO;
 	if (error)
 		goto out_free;
 

Broadcast regression confirmed fixed:
https://lore.kernel.org/regressions/[email protected]

# Librecast Test Results

010/010 [ OK ] libmld
120/120 [ OK ] liblibrecast

CPU/kernel: Linux auntie 5.15.191-rc1-00034-g29918c0c5b35 #59 SMP Tue Sep 2 16:08:44 -00 2025 x86_64 AMD Ryzen 9 9950X 16-Core Processor AuthenticAMD GNU/Linux

On ARCH_BRCMSTB using 32-bit and 64-bit ARM kernels, build tested on BMIPS_GENERIC:

Florian

All tests passing for Tegra ...

Test results for stable-v5.15:

    10 builds:	10 pass, 0 fail
    28 boots:	28 pass, 0 fail
    105 tests:	105 pass, 0 fail

Linux version: 5.15.191-rc1-g29918c0c5b35
Boards tested: tegra124-jetson-tk1, tegra186-p2771-0000,

                tegra186-p3509-0000+p3636-0001, tegra194-p2972-0000,
                tegra194-p3509-0000+p3668-0000, tegra20-ventana,
                tegra210-p2371-2180, tegra210-p3450-0000,
                tegra30-cardhu-a04

Jon

Results from Linaro’s test farm.
No regressions on arm64, arm, x86_64, and i386.

## Build
* kernel: 5.15.191-rc1
* git: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
* git commit: 29918c0c5b353baf87a2bbc3e2a4256c99430dba
* git describe: v5.15.190-34-g29918c0c5b35
* test details:
https://qa-reports.linaro.org/lkft/linux-stable-rc-linux-5.15.y/build/v5.15.190-34-g29918c0c5b35

## Test Regressions (compared to v5.15.189-645-ge09f9302f92d)

## Metric Regressions (compared to v5.15.189-645-ge09f9302f92d)

## Test Fixes (compared to v5.15.189-645-ge09f9302f92d)

## Metric Fixes (compared to v5.15.189-645-ge09f9302f92d)

## Test result summary
total: 55718, pass: 45636, fail: 2304, skip: 7414, xfail: 364

## Build Summary
* arc: 5 total, 5 passed, 0 failed
* arm: 101 total, 101 passed, 0 failed
* arm64: 28 total, 28 passed, 0 failed
* i386: 18 total, 18 passed, 0 failed
* mips: 22 total, 22 passed, 0 failed
* parisc: 3 total, 3 passed, 0 failed
* powerpc: 22 total, 22 passed, 0 failed
* riscv: 8 total, 8 passed, 0 failed
* s390: 9 total, 9 passed, 0 failed
* sh: 10 total, 10 passed, 0 failed
* sparc: 6 total, 6 passed, 0 failed
* x86_64: 24 total, 24 passed, 0 failed

## Test suites summary
* boot
* kselftest-arm64
* kselftest-breakpoints
* kselftest-capabilities
* kselftest-clone3
* kselftest-core
* kselftest-cpu-hotplug
* kselftest-exec
* kselftest-fpu
* kselftest-futex
* kselftest-intel_pstate
* kselftest-kcmp
* kselftest-livepatch
* kselftest-membarrier
* kselftest-mincore
* kselftest-mm
* kselftest-mqueue
* kselftest-net
* kselftest-net-mptcp
* kselftest-openat2
* kselftest-ptrace
* kselftest-rseq
* kselftest-rtc
* kselftest-seccomp
* kselftest-sigaltstack
* kselftest-size
* kselftest-tc-testing
* kselftest-timers
* kselftest-tmpfs
* kselftest-tpm2
* kselftest-user_events
* kselftest-vDSO
* kselftest-x86
* kunit
* kvm-unit-tests
* lava
* libgpiod
* libhugetlbfs
* log-parser-boot
* log-parser-build-clang
* log-parser-build-gcc
* log-parser-test
* ltp-capability
* ltp-commands
* ltp-containers
* ltp-controllers
* ltp-cpuhotplug
* ltp-crypto
* ltp-cve
* ltp-dio
* ltp-fcntl-locktests
* ltp-fs
* ltp-fs_bind
* ltp-fs_perms_simple
* ltp-hugetlb
* ltp-math
* ltp-mm
* ltp-nptl
* ltp-pty
* ltp-sched
* ltp-smoke
* ltp-syscalls
* ltp-tracing
* perf
* rcutorture

--
Linaro LKFT
https://lkft.linaro.org

No issues were seen on x86_64 and aarch64 platforms with our testing.

Built and booted successfully on RISC-V RV64 (HiFive Unmatched).