Skip to contentSkip to conversation

staging: gpib: Fix no EOI on 1 and 2 byte writes

PATCH New Dave Penkler 1 participant 1 message Sep 28, 2025 Staging

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 staging: gpib: Fix no EOI on 1 and 2 byte writes

EOI (End Or Identify) is a hardware line on the GPIB bus that can be asserted with the last byte of a message to indicate the end of the transfer to the receiving device.

In this driver, a write with send_eoi true is done in 3 parts:
Send first byte directly
Send remaining but 1 bytes using the fifo
Send the last byte directly with EOI asserted

The first byte in a write is always sent by writing to the tms9914 chip directly to setup for the subsequent fifo transfer. We were not checking for a 1 byte write with send_eoi true resulting in EOI not being asserted. Since the fifo transfer was not executed (fifotransfersize == 0) the retval in the test after the fifo transfer code was still 1 from the preceding direct write. This caused it to return without executing the final direct write which would have sent an unsollicited extra byte.

For a 2 byte message the first byte was sent directly. But since the fifo transfer was not executed (fifotransfersize == 1) and the retval in the test after the fifo transfer code was still 1 from the preceding first byte write it returned before the final direct byte write with send_eoi true. The second byte was then sent as a separate 1 byte write to complete the 2 byte write count again without EOI being asserted as above.

Only send the first byte directly if more than 1 byte is to be transferred with send_eoi true.

Also check for retval < 0 for the error return in case the fifo code is not used (1 or 2 byte message with send_eoi true).

Fixes 09a4655ee1eb ("staging: gpib: Add HP/Agilent/Keysight 8235xx PCI GPIB driver")
---
 drivers/staging/gpib/agilent_82350b/agilent_82350b.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/staging/gpib/agilent_82350b/agilent_82350b.c +7 -5
index 94bbb3b6576d..01a5bb43cd2d 100644
@@ -182,10 +182,12 @@ static int agilent_82350b_accel_write(struct gpib_board *board, u8 *buffer,
 		return retval;
 #endif
 
-	retval = agilent_82350b_write(board, buffer, 1, 0, &num_bytes);
-	*bytes_written += num_bytes;
-	if (retval < 0)
-		return retval;
+	if (fifotransferlength > 0) {
+		retval = agilent_82350b_write(board, buffer, 1, 0, &num_bytes);
+		*bytes_written += num_bytes;
+		if (retval < 0)
+			return retval;
+	}
 
 	write_byte(tms_priv, tms_priv->imr0_bits & ~HR_BOIE, IMR0);
 	for (i = 1; i < fifotransferlength;) {
@@ -217,7 +219,7 @@ static int agilent_82350b_accel_write(struct gpib_board *board, u8 *buffer,
 			break;
 	}
 	write_byte(tms_priv, tms_priv->imr0_bits, IMR0);
-	if (retval)
+	if (retval < 0)
 		return retval;
 
 	if (send_eoi) {
Signature · 1 line
2.51.0