Add support for dynamic MMU configuration
Subsystems (5)
v8 cover Add support for dynamic MMU configuration
Hi all,
In U-Boot, TI only provides a single memory map for all k3 platforms, this does not scale for devices where atf and optee lie outside the range 0x80000000
- 0x80080000 and 0x9e780000 - 0xa0000000 respectively.
There are also issues for devices with < 2GiB of memory (eg am62SiP with 512MiB of RAM) as the maximum size for the first DRAM bank is hardcoded to 2GiB in the current memory map. Furthermore the second DRAM bank is mapped even for devices that only have a single bank.
Therefore this patch set adds the required functionality to create the MMU table at runtime based on the device-tree.
The patch set has been build tested on all effected platforms but boot-tested only on TI's K3 EVMs, the beagleplay and phytec's phycore-am6* platforms.
The following effected boards have not been boot tested:
- verdin-am62
- iot2050
Best Wishes,
Anshul
---
Changes in v8:
- Reserve extra space for page table entries for performing fixups
v7: https://lore.kernel.org/u-boot/[email protected]/
Changes in v7:
- Pick up R-by and Tested-by tags
- Use nobreak API for unmapping MMU region
- Better error messages and minor refactor
v6: https://lore.kernel.org/u-boot/[email protected]/
Changes in v6:
- Make use of generic MMU APIs
- Extend core U-Boot functionality by adding mmu_unmap_reserved_mem and mem_map_fix_dram_banks
- Keep same memory maps for SPL and U-Boot proper
- Add fdt fixups from SPL stage for reserved memory nodes
v5: https://lore.kernel.org/u-boot/[email protected]/
Changes in v5:
- Don't create carveouts for every reserved-memory node
- Only create carveouts for ATF/OP-TEE
- Expand the call to k3_mem_map_init to vendor boards as well
- Map area for framebuffer for CONFIG_VIDEO=y platforms
v4: https://lore.kernel.org/u-boot/[email protected]/
Changes for v4:
- Add call to k3_mem_map_init for beagleplay
- Mark reserved regions as non-cacheable
- More debug logs
v3: https://lore.kernel.org/u-boot/[email protected]/
Changes for v3:
- Remove unused memory regions in SPL's map
- Add runtime addition of MMU entry for the framebuffer in SPL
- Refactor k3_mem_map_init to use standard u-boot APIs
- Unmap reserved-memory regions instead of keeping them uncached
v2: https://lore.kernel.org/u-boot/[email protected]/
Changes in v2:
- Removed dependency to:
https://lore.kernel.org/u-boot/[email protected]/
v1: https://lore.kernel.org/u-boot/[email protected]/
---
Anshul Dalal (11):
mach-k3: use minimal memory map for all K3
mach-k3: use custom enable_cache
arm: armv8: mmu: export mmu_setup
arm: armv8: invalidate dcache entries on dcache_enable
arm: armv8: mmu: add mem_map_fix_dram_banks
mach-k3: map all banks using mem_map_fix_dram_banks
arm: armv8: mmu: add mmu_unmap_reserved_mem
spl: split spl_board_fixups to arch/board specific
mach-k3: add reserved memory fixups for next boot stage
mach-k3: add carveouts for TFA and optee
arm: mach-k3: reserve space for page table entries
arch/arm/cpu/armv7m/cpu.c | 2 +- arch/arm/cpu/armv8/cache_v8.c | 58 ++++++++++++++++++++-- arch/arm/include/asm/armv8/mmu.h | 24 +++++++++ arch/arm/mach-k3/arm64/arm64-mmu.c | 40 +++++++-------- arch/arm/mach-k3/common.c | 55 ++++++++++++++++++++ arch/arm/mach-k3/include/mach/k3-ddr.h | 6 +++ arch/arm/mach-rockchip/spl-boot-order.c | 2 +- arch/arm/mach-socfpga/spl_soc64.c | 2 +- board/beagle/beagley-ai/beagley-ai.c | 2 +- board/dhelectronics/dh_stm32mp1/board.c | 2 +- board/phytec/phycore_am62x/phycore-am62x.c | 2 +- board/phytec/phycore_am64x/phycore-am64x.c | 2 +- board/renesas/sparrowhawk/sparrowhawk.c | 2 +- board/starfive/visionfive2/spl.c | 2 +- board/ti/am62ax/evm.c | 2 +- board/ti/am62px/evm.c | 2 +- board/ti/am62x/evm.c | 2 +- board/ti/am64x/evm.c | 2 +- board/ti/j721e/evm.c | 2 +- board/ti/j721s2/evm.c | 2 +- board/ti/j722s/evm.c | 2 +- board/ti/j784s4/evm.c | 2 +- common/spl/spl.c | 12 +++-- include/spl.h | 12 +++-- 24 files changed, 191 insertions(+), 50 deletions(-)
Signature · 1 line
2.51.0
PATCH v8 1/11 mach-k3: use minimal memory map for all K3
The K3 family of SoCs encompasses a wide variety of devices with varying DDR configurations and memory carveout requirements, the current static memory map provides basic support for TI EVMs but does not scale well for newer platforms (such as AM62SiP with 512MiB of RAM).
Therefore this patch replaces the existing memory map with a minimal one, that could be more easily modified at runtime.
--- arch/arm/mach-k3/arm64/arm64-mmu.c | 32 ++++++++++-------------------- 1 file changed, 10 insertions(+), 22 deletions(-)
arch/arm/mach-k3/arm64/arm64-mmu.c +10 -22
@@ -11,42 +11,30 @@#include <asm/system.h> #include <asm/armv8/mmu.h> +#include <linux/sizes.h> struct mm_region k3_mem_map[] = { - { + {/* SoC Peripherals */ .virt =0x0UL , .phys =0x0UL , .size =0x80000000UL , .attrs =PTE_BLOCK_MEMTYPE (MT_DEVICE_NGNRNE ) |PTE_BLOCK_NON_SHARE |PTE_BLOCK_PXN |PTE_BLOCK_UXN - }, { - .virt =0x80000000UL , - .phys =0x80000000UL , - .size =0x1e780000UL , - .attrs =PTE_BLOCK_MEMTYPE (MT_NORMAL ) | -PTE_BLOCK_INNER_SHARE - }, { - .virt =0xa0000000UL , - .phys =0xa0000000UL , - .size =0x60000000UL , - .attrs =PTE_BLOCK_MEMTYPE (MT_NORMAL ) | -PTE_BLOCK_INNER_SHARE - }, { - .virt =0x880000000UL , - .phys =0x880000000UL , - .size =0x80000000UL , - .attrs =PTE_BLOCK_MEMTYPE (MT_NORMAL ) | -PTE_BLOCK_INNER_SHARE - }, { + }, {/* Flash Peripherals */ .virt =0x500000000UL , .phys =0x500000000UL , .size =0x380000000UL , .attrs =PTE_BLOCK_MEMTYPE (MT_DEVICE_NGNRNE ) |PTE_BLOCK_NON_SHARE |PTE_BLOCK_PXN |PTE_BLOCK_UXN - }, { -/* List terminator */ + }, {/* First DRAM Bank of size 2G */ + .virt =CFG_SYS_SDRAM_BASE , + .phys =CFG_SYS_SDRAM_BASE , + .size =SZ_2G , + .attrs =PTE_BLOCK_MEMTYPE (MT_NORMAL ) | +PTE_BLOCK_INNER_SHARE + }, {/* List terminator */ 0 , } };
Signature · 1 line
2.51.0
PATCH v8 2/11 mach-k3: use custom enable_cache
In reply to Anshul DalalU-Boot's provided enable_caches enforces the following sequence:icache_enable -> mmu_setup (as part of dcache_enable) -> dcache_enable
Whereas for K3 devices, we would like to add entries to the provided static array (k3_mem_map) as per gd->bd->bi_dram and then call mmu_setup to configure the MMU but also create carveouts for TFA/TEE before we enable caches to prevent speculative accesses to the region. Thus the following desired sequence:
add dram banks -> mmu_setup -> carveout TFA/TEE -> icache/dcache enable
Therefore this patch adds K3's own implementation of enable_cache for ARM64, allowing for greater control over the cache enablement sequence.
--- arch/arm/mach-k3/common.c | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm/mach-k3/common.c +6 -0
@@ -258,6 +258,12 @@ void board_prep_linux(struct bootm_headers *images)ROUND (images->os.end, CONFIG_SYS_CACHELINE_SIZE)); } + +void enable_caches (void ) +{ +icache_enable (); +dcache_enable (); +}#endif void spl_enable_cache (void )
Signature · 1 line
2.51.0
PATCH v8 3/11 arm: armv8: mmu: export mmu_setup
In reply to Anshul DalalThe mmu_setup function configures the page tables based on the board supplied mem_map struct array. It is called implicitly as part of dcache_enable but this limits us to only be able to use APIs such as mmu_change_region_attr only after caches are enabled.
This might lead to speculative accesses before we can unmap a region that is marked as cacheable in the static memory map.
Therefore this patch exports the mmu_setup function in mmu.h allowing users to have more control over when the mmu is configured.
For K3 specifically this allows for the following configuration sequence as part of enable_caches:
static mem_map fixups (TODO) -> mmu_setup -> carveouts using mmu_change_region_attr (TODO) -> icache/dcache enable
--- arch/arm/include/asm/armv8/mmu.h | 5 +++++ arch/arm/mach-k3/common.c | 3 +++ 2 files changed, 8 insertions(+)
arch/arm/include/asm/armv8/mmu.h +5 -0
@@ -197,6 +197,11 @@ struct mm_region {extern struct mm_region *mem_map;void setup_pgtables (void );u64 get_tcr (u64 *pips,u64 *pva_bits); + +/** +* mmu_setup() - Sets up the mmu page tables as per mem_map +*/ +void mmu_setup (void );#endif #endif /* _ASM_ARMV8_MMU_H_ */
arch/arm/mach-k3/common.c +3 -0
@@ -30,6 +30,7 @@#include <soc.h> #include <dm/uclass-internal.h> #include <dm/device-internal.h> +#include <asm/armv8/mmu.h> #define PROC_BOOT_CTRL_FLAG_R5_CORE_HALT 0x00000001#define PROC_BOOT_STATUS_FLAG_R5_WFI 0x00000002
@@ -261,6 +262,8 @@ void board_prep_linux(struct bootm_headers *images)void enable_caches (void ) { +mmu_setup (); +icache_enable ();dcache_enable (); }
Signature · 1 line
2.51.0
PATCH v8 4/11 arm: armv8: invalidate dcache entries on dcache_enable
In reply to Anshul DalalIn dcache_enable, currently the dcache entries are only invalidated when the MMU is not enabled. This causes issues when dcache_enable is called with the MMU already configured, in such cases the existing dcache entries are not flushed which might result in un-expected behavior.
This patch invalidates the cache entries on every call of dcache_enable before enabling dcache (by setting CR_C). This makes dcache_enable behave similar to icache_enable as well.
--- arch/arm/cpu/armv8/cache_v8.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-)
arch/arm/cpu/armv8/cache_v8.c +3 -4
@@ -830,16 +830,15 @@ void flush_dcache_range(unsigned long start, unsigned long stop)void dcache_enable (void ) {/* The data cache is not active unless the mmu is enabled */ -if (!(get_sctlr () &CR_M )) { -invalidate_dcache_all (); -__asm_invalidate_tlb_all (); +if (!mmu_status ())mmu_setup (); - }/* Set up page tables only once (it is done also by mmu_setup()) */ if (!gd->arch.tlb_fillptr)setup_all_pgtables (); +invalidate_dcache_all (); +__asm_invalidate_tlb_all ();set_sctlr (get_sctlr () |CR_C ); }
Signature · 1 line
2.51.0
PATCH v8 5/11 arm: armv8: mmu: add mem_map_fix_dram_banks
In reply to Anshul DalalFor armv8, U-Boot uses a static map defined as 'mem_map' for configuring the MMU as part of mmu_setup.
But since the exact configuration of memory banks might not be known at build time, many platforms such as imx9, versal2 etc. utilize gd->bd->bi_dram to configure the static map at runtime.
Therefore this patch adds a new API mem_map_fix_dram_banks that modifies the static map in a similar way. Allowing the caller to map all dram banks by just passing the index to last entry in their mem_map and it's length.
--- arch/arm/cpu/armv8/cache_v8.c | 28 ++++++++++++++++++++++++++++ arch/arm/include/asm/armv8/mmu.h | 10 ++++++++++ 2 files changed, 38 insertions(+)
arch/arm/cpu/armv8/cache_v8.c +28 -0
@@ -58,6 +58,34 @@ static int get_effective_el(void)return el; } +int mem_map_fix_dram_banks (unsigned int index,unsigned int len,u64 attrs) +{ +unsigned int i; +int ret =fdtdec_setup_memory_banksize (); + +if (ret) { +printf ("%s: Failed to setup dram banks\n" , __func__); +return ret; + } + +if (index +CONFIG_NR_DRAM_BANKS >= len) { +printf ("%s: Provided mem_map array has insufficient size for DRAM entries\n" , + __func__); +return -ENOMEM ; + } + +for (i =0 ; i <CONFIG_NR_DRAM_BANKS ; i++) { + mem_map[index].virt = gd->bd->bi_dram[i].start; + mem_map[index].phys = gd->bd->bi_dram[i].start; + mem_map[index].size = gd->bd->bi_dram[i].size; + mem_map[index].attrs = attrs; + index++; + } + +memset (&mem_map[index],0 ,sizeof (mem_map[index])); + +return 0 ; +}u64 get_tcr (u64 *pips,u64 *pva_bits) {int el =get_effective_el ();
arch/arm/include/asm/armv8/mmu.h +10 -0
@@ -194,8 +194,18 @@ struct mm_region {u64 attrs; }; +/* Used as the memory map for MMU configuration by mmu_setup */ extern struct mm_region *mem_map;void setup_pgtables (void ); + +/** +* mem_map_fix_dram_banks() - Populate mem_map with entries corresponding to +* dram banks as per the gd. This should be called prior to mmu_setup. +* +* @index: The entry in mem_map to start the over-write +* @len: The size of mem_map +*/ +int mem_map_fix_dram_banks (unsigned int index,unsigned int len,u64 attrs);u64 get_tcr (u64 *pips,u64 *pva_bits);/**
Signature · 1 line
2.51.0
Re: [PATCH -next v8 05/11] arm: armv8: mmu: add mem_map_fix_dram_banks
Quoted 7 lines · Anshul Dalal
For armv8, U-Boot uses a static map defined as '
mem_map' for configuring the MMU as part ofmmu_setup.But since the exact configuration of memory banks might not be known at build time, many platforms such as imx9, versal2 etc. utilize
gd->bd->bi_dramto configure the static map at runtime.
Quoted 7 lines
Therefore this patch adds a new API
mem_map_fix_dram_banksthat modifies the static map in a similar way. Allowing the caller to map all dram banks by just passing the index to last entry in theirmem_mapand it's length.Signed-off-by Anshul Dalal <[email protected]>Tested-by Wadim Egorov <[email protected]>
Signature · 3 lines
Best regards, Dhruva Gole Texas Instruments Incorporated
PATCH v8 6/11 mach-k3: map all banks using mem_map_fix_dram_banks
In reply to Anshul DalalThe static memory map for K3 (k3_mem_map) only maps the first DRAM bank and therefore doesn't scale for platforms with multiple memory banks.
This patch modifies enable_caches to add mem_map_fix_dram_banks which appends all the memory banks to k3_mem_map before calling mmu_setup.
--- arch/arm/mach-k3/arm64/arm64-mmu.c | 5 +++-- arch/arm/mach-k3/common.c | 9 +++++++++ arch/arm/mach-k3/include/mach/k3-ddr.h | 6 ++++++ 3 files changed, 18 insertions(+), 2 deletions(-)
arch/arm/mach-k3/arm64/arm64-mmu.c +3 -2
@@ -12,8 +12,9 @@#include <asm/system.h> #include <asm/armv8/mmu.h> #include <linux/sizes.h> +#include <mach/k3-ddr.h> -struct mm_region k3_mem_map[] = { +struct mm_region k3_mem_map[K3_MEM_MAP_LEN ] = { {/* SoC Peripherals */ .virt =0x0UL , .phys =0x0UL ,
@@ -28,7 +29,7 @@ struct mm_region k3_mem_map[] = { .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | PTE_BLOCK_NON_SHARE | PTE_BLOCK_PXN | PTE_BLOCK_UXN - }, { /* First DRAM Bank of size 2G */ + }, [K3_MEM_MAP_FIRST_BANK_IDX] = { /* First DRAM Bank of size 2G */ .virt = CFG_SYS_SDRAM_BASE, .phys = CFG_SYS_SDRAM_BASE, .size = SZ_2G,
arch/arm/mach-k3/common.c +9 -0
@@ -31,6 +31,7 @@#include <dm/uclass-internal.h> #include <dm/device-internal.h> #include <asm/armv8/mmu.h> +#include <mach/k3-ddr.h> #define PROC_BOOT_CTRL_FLAG_R5_CORE_HALT 0x00000001#define PROC_BOOT_STATUS_FLAG_R5_WFI 0x00000002
@@ -262,6 +263,14 @@ void board_prep_linux(struct bootm_headers *images)void enable_caches (void ) { +int ret; + + ret =mem_map_fix_dram_banks (K3_MEM_MAP_FIRST_BANK_IDX ,K3_MEM_MAP_LEN , +PTE_BLOCK_MEMTYPE (MT_NORMAL ) | +PTE_BLOCK_INNER_SHARE ); +if (ret) +debug ("%s: Failed to setup dram banks\n" , __func__); +mmu_setup ();icache_enable ();
arch/arm/mach-k3/include/mach/k3-ddr.h +6 -0
@@ -8,6 +8,12 @@#include <spl.h> +/* We need 3 extra entries for: +* SoC peripherals, flash and the sentinel value. +*/ +#define K3_MEM_MAP_LEN ((CONFIG_NR_DRAM_BANKS) + 3) +#define K3_MEM_MAP_FIRST_BANK_IDX 2 +int dram_init (void );int dram_init_banksize (void );
Signature · 1 line
2.51.0
PATCH v8 7/11 arm: armv8: mmu: add mmu_unmap_reserved_mem
In reply to Anshul DalalFor armv8, U-Boot uses a static map defined as 'mem_map' for configuring the MMU's page tables, done by mmu_setup.
Though this works well for simpler platforms, it makes creating runtime carveouts by modifying the static array at runtime exceedingly complex like in mach-snapdragon/board.c.
Creation of such carveouts are much better handled by APIs such as mmu_change_region_attr once the page tables are configured. Usually such carveouts are configured via the device-tree's reserved-memory node which provides the address and size for the carveout.
Therefore this patch adds mmu_unmap_reserved_mem which acts as a wrapper over mmu_change_region_attr, helping unmap a reserved-memory region.
--- arch/arm/cpu/armv8/cache_v8.c | 23 +++++++++++++++++++++++ arch/arm/include/asm/armv8/mmu.h | 9 +++++++++ 2 files changed, 32 insertions(+)
arch/arm/cpu/armv8/cache_v8.c +23 -0
@@ -86,6 +86,29 @@ int mem_map_fix_dram_banks(unsigned int index, unsigned int len, u64 attrs)return 0 ; } + +int mmu_unmap_reserved_mem (const char *name) +{ +void *fdt = (void *)gd->fdt_blob; +char node_path[128 ]; +fdt_addr_t addr; +fdt_size_t size; +int ret; + +snprintf (node_path,sizeof (node_path),"/reserved-memory/%s" , name); + ret =fdt_path_offset (fdt, node_path); +if (ret <0 ) +return ret; + + addr =fdtdec_get_addr_size (fdt, ret,"reg" , &size); +if (addr ==FDT_ADDR_T_NONE ) +return -1 ; + +mmu_change_region_attr_nobreak (addr, size,PTE_TYPE_FAULT ); + +return 0 ; +} +u64 get_tcr (u64 *pips,u64 *pva_bits) {int el =get_effective_el ();
arch/arm/include/asm/armv8/mmu.h +9 -0
@@ -206,6 +206,15 @@ void setup_pgtables(void);* @len: The size of mem_map */ int mem_map_fix_dram_banks (unsigned int index,unsigned int len,u64 attrs); + +/** +* mmu_unmap_reserved_mem() - Unmaps a reserved-memory node as PTE_TYPE_FAULT +* once MMU is configured by mmu_setup. +* +* @name: The name of the node under "/reserved-memory/" path +*/ +int mmu_unmap_reserved_mem (const char *name); +u64 get_tcr (u64 *pips,u64 *pva_bits);/**
Signature · 1 line
2.51.0
PATCH v8 8/11 spl: split spl_board_fixups to arch/board specific
In reply to Anshul DalalThe current spl_board_fixups API allows for modification of spl_image before the SPL jumps to it. This can be used to modify the DT for the next boot stage, however the current API only allows either the machine arch or the board to use it.
This limits the utility of the API as there might be certain fixups that should be applied to all boards sharing the same machine architecture with others being board specific.
For TI's K3 specifically, this prevents us from performing architecture level fixups since a lot of TI boards are already making use of the spl_board_fixups API.
Therefore this patch splits the API into two to allow both board and the architecture specific fixups. The order is kept as arch then board to give board specific fixups the precedence.
--- arch/arm/cpu/armv7m/cpu.c | 2 +- arch/arm/mach-rockchip/spl-boot-order.c | 2 +- arch/arm/mach-socfpga/spl_soc64.c | 2 +- board/beagle/beagley-ai/beagley-ai.c | 2 +- board/dhelectronics/dh_stm32mp1/board.c | 2 +- board/phytec/phycore_am62x/phycore-am62x.c | 2 +- board/phytec/phycore_am64x/phycore-am64x.c | 2 +- board/renesas/sparrowhawk/sparrowhawk.c | 2 +- board/starfive/visionfive2/spl.c | 2 +- board/ti/am62ax/evm.c | 2 +- board/ti/am62px/evm.c | 2 +- board/ti/am62x/evm.c | 2 +- board/ti/am64x/evm.c | 2 +- board/ti/j721e/evm.c | 2 +- board/ti/j721s2/evm.c | 2 +- board/ti/j722s/evm.c | 2 +- board/ti/j784s4/evm.c | 2 +- common/spl/spl.c | 12 +++++++++--- include/spl.h | 12 +++++++++--- 19 files changed, 35 insertions(+), 23 deletions(-)
arch/arm/cpu/armv7m/cpu.c +1 -1
@@ -57,7 +57,7 @@ void reset_cpu(void) | V7M_AIRCR_SYSRESET, &V7M_SCB->aircr); } -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_arch_fixups (struct spl_image_info *spl_image) { spl_image->entry_point |=0x1 ; }
arch/arm/mach-rockchip/spl-boot-order.c +1 -1
@@ -240,7 +240,7 @@ int spl_decode_boot_device(u32 boot_device, char *buf, size_t buflen)#endif } -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_arch_fixups (struct spl_image_info *spl_image) {const char *bootrom_ofpath =board_spl_was_booted_from ();void *blob =spl_image_fdt_addr (spl_image);
arch/arm/mach-socfpga/spl_soc64.c +1 -1
@@ -130,7 +130,7 @@ u32 spl_boot_mode(const u32 boot_device)#endif /* board specific function prior loading SSBL / U-Boot */ -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_arch_fixups (struct spl_image_info *spl_image) {int ret;struct udevice *dev;
board/beagle/beagley-ai/beagley-ai.c +1 -1
@@ -32,7 +32,7 @@ int dram_init_banksize(void) }#if defined(CONFIG_XPL_BUILD ) -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {if (IS_ENABLED (CONFIG_K3_DDRSS )) {if (IS_ENABLED (CONFIG_K3_INLINE_ECC ))
board/dhelectronics/dh_stm32mp1/board.c +1 -1
@@ -776,7 +776,7 @@ int ft_board_setup(void *blob, struct bd_info *bd)#endif #if defined(CONFIG_XPL_BUILD ) -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {dh_stm32_ks8851_fixup (spl_image_fdt_addr (spl_image)); }
board/phytec/phycore_am62x/phycore-am62x.c +1 -1
@@ -199,7 +199,7 @@ int do_board_detect(void)#endif #if IS_ENABLED (CONFIG_XPL_BUILD ) -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {if (IS_ENABLED (CONFIG_K3_DDRSS ) &&IS_ENABLED (CONFIG_K3_INLINE_ECC ))fixup_ddr_driver_for_ecc (spl_image);
board/phytec/phycore_am64x/phycore-am64x.c +1 -1
@@ -118,7 +118,7 @@ int do_board_detect(void)#endif #if IS_ENABLED (CONFIG_XPL_BUILD ) -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {if (IS_ENABLED (CONFIG_K3_DDRSS ) &&IS_ENABLED (CONFIG_K3_INLINE_ECC ))fixup_ddr_driver_for_ecc (spl_image);
board/renesas/sparrowhawk/sparrowhawk.c +1 -1
@@ -134,7 +134,7 @@ unsigned int spl_spi_get_uboot_offs(struct spi_flash *flash)return CONFIG_SYS_SPI_U_BOOT_OFFS ; } -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {void *blob =spl_image_fdt_addr (spl_image);int err, offs;
board/starfive/visionfive2/spl.c +1 -1
@@ -20,7 +20,7 @@ DECLARE_GLOBAL_DATA_PTR;#define JH7110_CLK_CPU_ROOT_SHIFT 24#define JH7110_CLK_CPU_ROOT_MASK GENMASK(29, 24) -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {/* Update the memory size which read from eeprom or DT */ if (spl_image->fdt_addr)
board/ti/am62ax/evm.c +1 -1
@@ -17,7 +17,7 @@#include "../common/fdt_ops.h" #if defined(CONFIG_XPL_BUILD ) -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {if (IS_ENABLED (CONFIG_K3_DDRSS )) {if (IS_ENABLED (CONFIG_K3_INLINE_ECC ))
board/ti/am62px/evm.c +1 -1
@@ -50,7 +50,7 @@ void spl_board_init(void)#endif #if defined(CONFIG_XPL_BUILD ) -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {if (IS_ENABLED (CONFIG_K3_DDRSS )) {if (IS_ENABLED (CONFIG_K3_INLINE_ECC ))
board/ti/am62x/evm.c +1 -1
@@ -91,7 +91,7 @@ void spl_board_init(void) } -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {if (IS_ENABLED (CONFIG_K3_DDRSS )) {if (IS_ENABLED (CONFIG_K3_INLINE_ECC ))
board/ti/am64x/evm.c +1 -1
@@ -98,7 +98,7 @@ static int fixup_usb_boot(const void *fdt_blob) }#endif -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {if (IS_ENABLED (CONFIG_K3_DDRSS )) {if (IS_ENABLED (CONFIG_K3_INLINE_ECC ))
board/ti/j721e/evm.c +1 -1
@@ -127,7 +127,7 @@ static void __maybe_unused detect_enable_hyperflash(void *blob)#if defined(CONFIG_XPL_BUILD ) && (defined(CONFIG_TARGET_J7200_A72_EVM ) || defined(CONFIG_TARGET_J7200_R5_EVM ) || \ defined(CONFIG_TARGET_J721E_A72_EVM ) || defined(CONFIG_TARGET_J721E_R5_EVM )) -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {detect_enable_hyperflash (spl_image->fdt_addr); }
board/ti/j721s2/evm.c +1 -1
@@ -40,7 +40,7 @@ phys_addr_t board_get_usable_ram_top(phys_size_t total_size) }#if defined(CONFIG_XPL_BUILD ) -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {if (IS_ENABLED (CONFIG_K3_DDRSS )) {if (IS_ENABLED (CONFIG_K3_INLINE_ECC ))
board/ti/j722s/evm.c +1 -1
@@ -24,7 +24,7 @@ void spl_board_init(void)#endif #if defined(CONFIG_XPL_BUILD ) -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {if (IS_ENABLED (CONFIG_K3_DDRSS )) {if (IS_ENABLED (CONFIG_K3_INLINE_ECC ))
board/ti/j784s4/evm.c +1 -1
@@ -42,7 +42,7 @@ struct efi_capsule_update_info update_info = { };#if defined(CONFIG_XPL_BUILD ) -void spl_perform_fixups (struct spl_image_info *spl_image) +void spl_perform_board_fixups (struct spl_image_info *spl_image) {if (IS_ENABLED (CONFIG_K3_DDRSS )) {if (IS_ENABLED (CONFIG_K3_INLINE_ECC ))
common/spl/spl.c +9 -3
@@ -120,8 +120,13 @@ int __weak booti_setup(ulong image, ulong *relocated_addr, ulong *size, bool for }#endif -/* Weak default function for arch/board-specific fixups to the spl_image_info */ -void __weak spl_perform_fixups (struct spl_image_info *spl_image) +/* Weak default function for arch specific fixups to the spl_image_info */ +void __weak spl_perform_arch_fixups (struct spl_image_info *spl_image) +{ +} + +/* Weak default function for board specific fixups to the spl_image_info */ +void __weak spl_perform_board_fixups (struct spl_image_info *spl_image) { }
@@ -775,7 +780,8 @@ void board_init_r(gd_t *dummy1, ulong dummy2)hang (); } -spl_perform_fixups (&spl_image); +spl_perform_arch_fixups (&spl_image); +spl_perform_board_fixups (&spl_image); os = spl_image.os;if (os ==IH_OS_U_BOOT ) {
include/spl.h +9 -3
@@ -1116,10 +1116,16 @@ int board_return_to_bootrom(struct spl_image_info *spl_image,ulong board_spl_fit_size_align (ulong size);/** -* spl_perform_fixups() - arch/board-specific callback before processing -* the boot-payload +* spl_perform_arch_fixups() - arch specific callback before processing the +* boot-payload */ -void spl_perform_fixups (struct spl_image_info *spl_image); +void spl_perform_arch_fixups (struct spl_image_info *spl_image); + +/** +* spl_perform_board_fixups() - board specific callback before processing the +* boot-payload +*/ +void spl_perform_board_fixups (struct spl_image_info *spl_image);/* * spl_get_load_buffer() - get buffer for loading partial image data
Signature · 1 line
2.51.0
Re: [PATCH -next v8 08/11] spl: split spl_board_fixups to arch/board specific
Quoted 13 lines · Anshul Dalal
The current
spl_board_fixupsAPI allows for modification ofspl_imagebefore the SPL jumps to it. This can be used to modify the DT for the next boot stage, however the current API only allows either the machine arch or the board to use it.This limits the utility of the API as there might be certain fixups that should be applied to all boards sharing the same machine architecture with others being board specific.
For TI's K3 specifically, this prevents us from performing architecture level fixups since a lot of TI boards are already making use of the
spl_board_fixupsAPI.
Quoted 6 lines
Therefore this patch splits the API into two to allow both board and the architecture specific fixups. The order is kept as arch then board to give board specific fixups the precedence.
Signed-off-by Anshul Dalal <[email protected]>Tested-by Wadim Egorov <[email protected]>
Signature · 3 lines
Best regards, Dhruva Gole Texas Instruments Incorporated
PATCH v8 9/11 mach-k3: add reserved memory fixups for next boot stage
In reply to Anshul DalalThe boot flow in K3 platforms requires the subsequent boot stages to be aware of the memory reserved for previous boot binaries. In the regular boot sequence of:
R5 SPL -> ATF -> OP-TEE -> A-core SPL -> U-Boot -> Kernel,
Both A-core SPL and U-Boot should be made aware of the memory reserved for ATF and OP-TEE from their device-tree. Currently this information is absent.
Therefore this patch adds the reserved-memory regions as part of spl_perform_arch_fixups for the next stage's DT. This is called during both R5 and A-core SPL which fixes up the DT for their respective next
stages: A-core SPL and U-Boot proper.
--- arch/arm/mach-k3/common.c | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm/mach-k3/common.c +11 -0
@@ -321,6 +321,17 @@ static __maybe_unused void k3_dma_remove(void)pr_warn ("DMA Device not found (err=%d)\n" , rc); } +void spl_perform_arch_fixups (struct spl_image_info *spl_image) +{ +void *fdt =spl_image_fdt_addr (spl_image); + +if (!fdt) +return ; + +fdt_fixup_reserved (fdt,"tfa" ,CONFIG_K3_ATF_LOAD_ADDR ,0x80000 ); +fdt_fixup_reserved (fdt,"optee" ,CONFIG_K3_OPTEE_LOAD_ADDR ,0x1800000 ); +} +void spl_board_prepare_for_boot (void ) {#if !(defined(CONFIG_SYS_ICACHE_OFF ) && defined(CONFIG_SYS_DCACHE_OFF ))
Signature · 1 line
2.51.0
Re: [PATCH -next v8 09/11] mach-k3: add reserved memory fixups for next boot stage
Quoted 30 lines · Anshul Dalal
The boot flow in K3 platforms requires the subsequent boot stages to be aware of the memory reserved for previous boot binaries. In the regular boot sequence of:
R5 SPL -> ATF -> OP-TEE -> A-core SPL -> U-Boot -> Kernel,
Both A-core SPL and U-Boot should be made aware of the memory reserved for ATF and OP-TEE from their device-tree. Currently this information is absent.
Therefore this patch adds the reserved-memory regions as part of
spl_perform_arch_fixupsfor the next stage's DT. This is called during both R5 and A-core SPL which fixes up the DT for their respective next
stages: A-core SPL and U-Boot proper.Signed-off-by Anshul Dalal <[email protected]>Tested-by Wadim Egorov <[email protected]>--- arch/arm/mach-k3/common.c | 11 +++++++++++ 1 file changed, 11 insertions(+)arch/arm/mach-k3/common.c +1
-0@@ -321,6 +321,17 @@ static __maybe_unused void k3_dma_remove(void)pr_warn ("DMA Device not found (err=%d)\n" , rc); } +void spl_perform_arch_fixups (struct spl_image_info *spl_image)
arch/arm/mach-k3/common.c static __maybe_unused void k3_dma_remove(void) · line 334
Quoted 10 lines
arch/arm/mach-k3/common.c +10
-0+{ +void *fdt =spl_image_fdt_addr (spl_image); + +if (!fdt) +return ; + +fdt_fixup_reserved (fdt,"tfa" ,CONFIG_K3_ATF_LOAD_ADDR ,0x80000 ); +fdt_fixup_reserved (fdt,"optee" ,CONFIG_K3_OPTEE_LOAD_ADDR ,0x1800000 ); +} +
Signature · 3 lines
Best regards, Dhruva Gole Texas Instruments Incorporated
PATCH v8 10/11 mach-k3: add carveouts for TFA and optee
In reply to Anshul DalalK3 platforms have reserved memory regions for TFA and OPTEE which should be unmapped for U-Boot.
Therefore this patch adds the necessary fdt fixups to properly set the load address for TFA/OPTEE and unmaps both by mmu_unmap_reserved_mem.
--- arch/arm/mach-k3/common.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)
arch/arm/mach-k3/common.c +26 -0
@@ -31,6 +31,7 @@#include <dm/uclass-internal.h> #include <dm/device-internal.h> #include <asm/armv8/mmu.h> +#include <mach/k3-common-fdt.h> #include <mach/k3-ddr.h> #define PROC_BOOT_CTRL_FLAG_R5_CORE_HALT 0x00000001
@@ -263,6 +264,7 @@ void board_prep_linux(struct bootm_headers *images)void enable_caches (void ) { +void *fdt = (void *)gd->fdt_blob;int ret; ret = mem_map_fix_dram_banks(K3_MEM_MAP_FIRST_BANK_IDX, K3_MEM_MAP_LEN,
@@ -273,6 +275,30 @@ void enable_caches(void)mmu_setup (); +if (CONFIG_K3_ATF_LOAD_ADDR >=CFG_SYS_SDRAM_BASE ) { + ret =fdt_fixup_reserved (fdt,"tfa" ,CONFIG_K3_ATF_LOAD_ADDR , +0x80000 ); +if (ret) +debug ("%s: Failed to perform tfa fixups (%s)\n" , + __func__,fdt_strerror (ret)); + ret =mmu_unmap_reserved_mem ("tfa" ); +if (ret) +debug ("%s: Failed to unmap tfa reserved mem (%d)\n" , + __func__, ret); + } + +if (CONFIG_K3_OPTEE_LOAD_ADDR >=CFG_SYS_SDRAM_BASE ) { + ret =fdt_fixup_reserved (fdt,"optee" , +CONFIG_K3_OPTEE_LOAD_ADDR ,0x1800000 ); +if (ret) +debug ("%s: Failed to perform optee fixups (%s)\n" , + __func__,fdt_strerror (ret)); + ret =mmu_unmap_reserved_mem ("optee" ); +if (ret) +debug ("%s: Failed to unmap optee reserved mem (%d)\n" , + __func__, ret); + } +icache_enable ();dcache_enable (); }
Signature · 1 line
2.51.0
Re: [PATCH -next v8 10/11] mach-k3: add carveouts for TFA and optee
Quoted 48 lines · Anshul Dalal
K3 platforms have reserved memory regions for TFA and OPTEE which should be unmapped for U-Boot.
Therefore this patch adds the necessary fdt fixups to properly set the load address for TFA/OPTEE and unmaps both by
mmu_unmap_reserved_mem.Signed-off-by Anshul Dalal <[email protected]>Tested-by Wadim Egorov <[email protected]>--- arch/arm/mach-k3/common.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)arch/arm/mach-k3/common.c +14
-0@@ -31,6 +31,7 @@#include <dm/uclass-internal.h> #include <dm/device-internal.h> #include <asm/armv8/mmu.h> +#include <mach/k3-common-fdt.h> #include <mach/k3-ddr.h> #define PROC_BOOT_CTRL_FLAG_R5_CORE_HALT 0x00000001@@ -263,6 +264,7 @@ void board_prep_linux(struct bootm_headers *images)void enable_caches (void ) { +void *fdt = (void *)gd->fdt_blob;int ret; ret = mem_map_fix_dram_banks(K3_MEM_MAP_FIRST_BANK_IDX, K3_MEM_MAP_LEN,@@ -273,6 +275,30 @@ void enable_caches(void)mmu_setup (); +if (CONFIG_K3_ATF_LOAD_ADDR >=CFG_SYS_SDRAM_BASE ) { + ret =fdt_fixup_reserved (fdt,"tfa" ,CONFIG_K3_ATF_LOAD_ADDR , +0x80000 ); +if (ret) +debug ("%s: Failed to perform tfa fixups (%s)\n" , + __func__,fdt_strerror (ret)); + ret =mmu_unmap_reserved_mem ("tfa" ); +if (ret) +debug ("%s: Failed to unmap tfa reserved mem (%d)\n" , + __func__, ret); + } +
arch/arm/mach-k3/common.c void enable_caches(void) · line 299
Quoted 10 lines
arch/arm/mach-k3/common.c +10
-0+if (CONFIG_K3_OPTEE_LOAD_ADDR >=CFG_SYS_SDRAM_BASE ) { + ret =fdt_fixup_reserved (fdt,"optee" , +CONFIG_K3_OPTEE_LOAD_ADDR ,0x1800000 ); +if (ret) +debug ("%s: Failed to perform optee fixups (%s)\n" , + __func__,fdt_strerror (ret)); + ret =mmu_unmap_reserved_mem ("optee" ); +if (ret) +debug ("%s: Failed to unmap optee reserved mem (%d)\n" , + __func__, ret);
All these are hardly "debug" messages. Use something like error() or pr_err?
With that,
Signature · 3 lines
Best regards, Dhruva Gole Texas Instruments Incorporated
PATCH v8 11/11 arm: mach-k3: reserve space for page table entries
In reply to Anshul DalalWith the memory map configuration being done dynamically, reserve extra space during U-Boot relocation to ensure we have enough for the fixups.
--- arch/arm/mach-k3/arm64/arm64-mmu.c | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm/mach-k3/arm64/arm64-mmu.c +5 -0
@@ -41,3 +41,8 @@ struct mm_region k3_mem_map[K3_MEM_MAP_LEN] = { };struct mm_region *mem_map = k3_mem_map; + +u64 get_page_table_size (void ) +{ +return SZ_128K ; +}
Signature · 1 line
2.51.0
Re: [PATCH -next v8 11/11] arm: mach-k3: reserve space for page table entries
Quoted 13 lines · Anshul Dalal
With the memory map configuration being done dynamically, reserve extra space during U-Boot relocation to ensure we have enough for the fixups.
Signed-off-by Anshul Dalal <[email protected]>--- arch/arm/mach-k3/arm64/arm64-mmu.c | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/mach-k3/arm64/arm64-mmu.c +0
-0
arch/arm/mach-k3/arm64/arm64-mmu.c struct mm_region k3_mem_map[K3_MEM_MAP_LEN] = { · line 48
Quoted 8 lines
arch/arm/mach-k3/arm64/arm64-mmu.c +5
-0@@ -41,3 +41,8 @@ struct mm_region k3_mem_map[K3_MEM_MAP_LEN] = { };struct mm_region *mem_map = k3_mem_map; + +u64 get_page_table_size (void ) +{ +return SZ_128K ; +}
Signature · 3 lines
Best regards, Dhruva Gole Texas Instruments Incorporated
Re: [PATCH -next v8 11/11] arm: mach-k3: reserve space for page table entries
In reply to Anshul DalalOn October 6, 2025 thus sayeth Anshul Dalal:
Quoted 13 lines
With the memory map configuration being done dynamically, reserve extra space during U-Boot relocation to ensure we have enough for the fixups.
Signed-off-by Anshul Dalal <[email protected]>--- arch/arm/mach-k3/arm64/arm64-mmu.c | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/mach-k3/arm64/arm64-mmu.c +0
-0
arch/arm/mach-k3/arm64/arm64-mmu.c struct mm_region k3_mem_map[K3_MEM_MAP_LEN] = { · line 48
Quoted 8 lines
arch/arm/mach-k3/arm64/arm64-mmu.c +5
-0@@ -41,3 +41,8 @@ struct mm_region k3_mem_map[K3_MEM_MAP_LEN] = { };struct mm_region *mem_map = k3_mem_map; + +u64 get_page_table_size (void ) +{ +return SZ_128K ; +}
How are we calculating this size? With 2^39 addresses this should bring us into the MBs of TLB data.
I see we limit U-Boot to 512 entries, but that doesn't match this either
~Bryan
Re: [PATCH -next v8 11/11] arm: mach-k3: reserve space for page table entries
Quoted 26 lines · Bryan Brattlof
On October 6, 2025 thus sayeth Anshul Dalal:
Quoted 13 lines
With the memory map configuration being done dynamically, reserve extra space during U-Boot relocation to ensure we have enough for the fixups.
Signed-off-by Anshul Dalal <[email protected]>--- arch/arm/mach-k3/arm64/arm64-mmu.c | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/mach-k3/arm64/arm64-mmu.c +0
-0arch/arm/mach-k3/arm64/arm64-mmu.c struct mm_region k3_mem_map[K3_MEM_MAP_LEN] = { · line 48
Quoted 8 lines
arch/arm/mach-k3/arm64/arm64-mmu.c +5
-0@@ -41,3 +41,8 @@ struct mm_region k3_mem_map[K3_MEM_MAP_LEN] = { };struct mm_region *mem_map = k3_mem_map; + +u64 get_page_table_size (void ) +{ +return SZ_128K ; +}How are we calculating this size? With 2^39 addresses this should bring us into the MBs of TLB data.
Quoted 2 lines
I see we limit U-Boot to 512 entries, but that doesn't match this either
Of the current K3 devices, the largest reported size for the fixed up memory maps was ~32KiB with AM62 SiP (TFA@80000000 and TEE@80080000).
With the carveouts not aligned to 2MiB, maximum size I saw was ~64KiB. So with an added 2x margin of safety, I arrived at 128KiB ;)
This is enough for all current K3 devices and we can always increase it later if need be. As the panic we would get is pretty self explanatory:
Insufficient RAM for page table: 0x3000 > 0x2000. Please increase the size in get_page_table_size()
Regards,
Anshul
Hi Anshul,
Apologies for not looking at this earlier.
I'll have a look within the week.
Regards
/Ilias
Quoted 111 lines · Anshul Dalal
Hi all,
In U-Boot, TI only provides a single memory map for all k3 platforms, this does not scale for devices where atf and optee lie outside the range
0x80000000
-0x80080000and0x9e780000-0xa0000000respectively.There are also issues for devices with < 2GiB of memory (eg am62SiP with 512MiB of RAM) as the maximum size for the first DRAM bank is hardcoded to 2GiB in the current memory map. Furthermore the second DRAM bank is mapped even for devices that only have a single bank.
Therefore this patch set adds the required functionality to create the MMU table at runtime based on the device-tree.
The patch set has been build tested on all effected platforms but boot-tested only on TI's K3 EVMs, the beagleplay and phytec's phycore-am6* platforms.
The following effected boards have not been boot tested:
- verdin-am62
- iot2050Best Wishes,
Anshul
---
Changes in v8:
- Reserve extra space for page table entries for performing fixups
v7: https://lore.kernel.org/u-boot/[email protected]/Changes in v7:
- Pick up R-by and Tested-by tags
- Use nobreak API for unmapping MMU region
- Better error messages and minor refactor
v6: https://lore.kernel.org/u-boot/[email protected]/Changes in v6:
- Make use of generic MMU APIs
- Extend core U-Boot functionality by addingmmu_unmap_reserved_memandmem_map_fix_dram_banks
- Keep same memory maps for SPL and U-Boot proper
- Add fdt fixups from SPL stage for reserved memory nodes
v5: https://lore.kernel.org/u-boot/[email protected]/Changes in v5:
- Don't create carveouts for every reserved-memory node
- Only create carveouts for ATF/OP-TEE
- Expand the call tok3_mem_map_initto vendor boards as well
- Map area for framebuffer forCONFIG_VIDEO=yplatforms
v4: https://lore.kernel.org/u-boot/[email protected]/Changes for v4:
- Add call tok3_mem_map_initfor beagleplay
- Mark reserved regions as non-cacheable
- More debug logs
v3: https://lore.kernel.org/u-boot/[email protected]/Changes for v3:
- Remove unused memory regions in SPL's map
- Add runtime addition of MMU entry for the framebuffer in SPL
- Refactork3_mem_map_initto use standard u-boot APIs
- Unmap reserved-memory regions instead of keeping them uncached
v2: https://lore.kernel.org/u-boot/[email protected]/Changes in v2:
- Removed dependency to:
https://lore.kernel.org/u-boot/[email protected]/
v1: https://lore.kernel.org/u-boot/[email protected]/
---Anshul Dalal (11):
mach-k3: use minimal memory map for all K3
mach-k3: use customenable_cache
arm: armv8: mmu: exportmmu_setup
arm: armv8: invalidate dcache entries ondcache_enable
arm: armv8: mmu: addmem_map_fix_dram_banks
mach-k3: map all banks usingmem_map_fix_dram_banks
arm: armv8: mmu: addmmu_unmap_reserved_mem
spl: splitspl_board_fixupstoarch/boardspecific
mach-k3: add reserved memory fixups for next boot stage
mach-k3: add carveouts for TFA and optee
arm: mach-k3: reserve space for page table entriesarch/arm/cpu/armv7m/cpu.c | 2 +- arch/arm/cpu/armv8/cache_v8.c | 58 ++++++++++++++++++++-- arch/arm/include/asm/armv8/mmu.h | 24 +++++++++ arch/arm/mach-k3/arm64/arm64-mmu.c | 40 +++++++-------- arch/arm/mach-k3/common.c | 55 ++++++++++++++++++++ arch/arm/mach-k3/include/mach/k3-ddr.h | 6 +++ arch/arm/mach-rockchip/spl-boot-order.c | 2 +- arch/arm/mach-socfpga/spl_soc64.c | 2 +- board/beagle/beagley-ai/beagley-ai.c | 2 +- board/dhelectronics/dh_stm32mp1/board.c | 2 +- board/phytec/phycore_am62x/phycore-am62x.c | 2 +- board/phytec/phycore_am64x/phycore-am64x.c | 2 +- board/renesas/sparrowhawk/sparrowhawk.c | 2 +- board/starfive/visionfive2/spl.c | 2 +- board/ti/am62ax/evm.c | 2 +- board/ti/am62px/evm.c | 2 +- board/ti/am62x/evm.c | 2 +- board/ti/am64x/evm.c | 2 +- board/ti/j721e/evm.c | 2 +- board/ti/j721s2/evm.c | 2 +- board/ti/j722s/evm.c | 2 +- board/ti/j784s4/evm.c | 2 +- common/spl/spl.c | 12 +++-- include/spl.h | 12 +++-- 24 files changed, 191 insertions(+), 50 deletions(-)--
2.51.0