Skip to contentSkip to conversation

PCI: mediatek: add support AN7583 + YAML rework

PATCH Applied Christian Marangi 5 participants 14 messages Oct 12, 2025 – Oct 20, 2025

Subsystems (5)

v5 of 6 Applied Latest is v6 →

lore
Share & tools
lore
#0 lore raw

v5 cover PCI: mediatek: add support AN7583 + YAML rework

This little series convert the PCIe GEN2 Documentation to YAML schema and adds support for Airoha AN7583 GEN2 PCIe Controller.

Changes v5:
- Drop redudant entry from AN7583 patch
- Fix YAML error for AN7583 patch (sorry) Changes v4:
- Additional fix/improvement for YAML conversion
- Add review tag
- Fix wording on hifsys patch
- Rework PCI driver to flags and improve PBus logic Changes v3:
- Rework patch 1 to drop syscon compatible Changes v2:
- Add cover letter
- Describe skip_pcie_rstb variable
- Fix hifsys schema (missing syscon)
- Address comments on the YAML schema for PCIe GEN2
- Keep alphabetical order for AN7583

Christian Marangi (5):
ARM: dts: mediatek: drop wrong syscon hifsys compatible for

    MT2701/7623

dt-bindings: PCI: mediatek: Convert to YAML schema
dt-bindings: PCI: mediatek: Add support for Airoha AN7583
PCI: mediatek: convert bool to single flags entry and bitmap
PCI: mediatek: add support for Airoha AN7583 SoC

 .../bindings/pci/mediatek-pcie-mt7623.yaml    | 164 +++++++
 .../devicetree/bindings/pci/mediatek-pcie.txt | 289 ------------
 .../bindings/pci/mediatek-pcie.yaml           | 438 ++++++++++++++++++
 arch/arm/boot/dts/mediatek/mt2701.dtsi        |   2 +-
 arch/arm/boot/dts/mediatek/mt7623.dtsi        |   3 +-
 drivers/pci/controller/pcie-mediatek.c        | 120 +++--
 6 files changed, 690 insertions(+), 326 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie-mt7623.yaml
 delete mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie.txt
 create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie.yaml
Signature · 1 line
2.51.0
#1 lore raw

PATCH v5 1/5 ARM: dts: mediatek: drop wrong syscon hifsys compatible for MT2701/7623

The syscon compatible for the hifsys node for Mediatek MT2701/MT7623 SoC was wrongly added following the pattern of other clock node but it's actually not needed as the register are not used by other device on the SoC.

On top of this it's against the schema for hifsys YAML and causes a dtbs_check warning.

Drop the "syscon" compatible to mute the warning and reflect the compatible property described in the mediatek,mt2701-hifsys.yaml schema.

---
 arch/arm/boot/dts/mediatek/mt2701.dtsi | 2 +-
 arch/arm/boot/dts/mediatek/mt7623.dtsi | 3 +--
 2 files changed, 2 insertions(+), 3 deletions(-)
arch/arm/boot/dts/mediatek/mt2701.dtsi +1 -1
index ce6a4015fed5..128b87229f3d 100644
@@ -597,7 +597,7 @@ larb1: larb@16010000 {
 	};
 
 	hifsys: syscon@1a000000 {
-		compatible = "mediatek,mt2701-hifsys", "syscon";
+		compatible = "mediatek,mt2701-hifsys";
 		reg = <0 0x1a000000 0 0x1000>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
arch/arm/boot/dts/mediatek/mt7623.dtsi +1 -2
index fd7a89cc337d..4b1685b93989 100644
@@ -744,8 +744,7 @@ vdecsys: syscon@16000000 {
 
 	hifsys: syscon@1a000000 {
 		compatible = "mediatek,mt7623-hifsys",
-			     "mediatek,mt2701-hifsys",
-			     "syscon";
+			     "mediatek,mt2701-hifsys";
 		reg = <0 0x1a000000 0 0x1000>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
Signature · 1 line
2.51.0
#2 lore raw

PATCH v5 2/5 dt-bindings: PCI: mediatek: Convert to YAML schema

In reply to Christian Marangi

Convert the PCI mediatek Documentation to YAML schema to enable validation of the supported GEN1/2 Mediatek PCIe controller.

While converting, lots of cleanup were done from the .txt with better specifying what is supported by the various PCIe controller variant and drop of redundant info that are part of the standard PCIe Host Bridge schema.

To reduce schema complexity the .txt is split in 2 YAML, one for mt7623/mt2701 and the other for every other compatible.

---
 .../bindings/pci/mediatek-pcie-mt7623.yaml    | 164 +++++++++
 .../devicetree/bindings/pci/mediatek-pcie.txt | 289 ----------------
 .../bindings/pci/mediatek-pcie.yaml           | 318 ++++++++++++++++++
 3 files changed, 482 insertions(+), 289 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie-mt7623.yaml
 delete mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie.txt
 create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie.yaml
Documentation/devicetree/bindings/pci/mediatek-pcie-mt7623.yaml new file +164 -0
new file mode 100644
index 000000000000..e33bcc216e30
@@ -0,0 +1,164 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/mediatek-pcie-mt7623.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PCIe controller on MediaTek SoCs
+
+maintainers:
+  - Christian Marangi <[email protected]>
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-pcie
+      - mediatek,mt7623-pcie
+
+  reg:
+    minItems: 4
+    maxItems: 4
+
+  reg-names:
+    items:
+      - const: subsys
+      - const: port0
+      - const: port1
+      - const: port2
+
+  clocks:
+    minItems: 4
+    maxItems: 4
+
+  clock-names:
+    items:
+      - const: free_ck
+      - const: sys_ck0
+      - const: sys_ck1
+      - const: sys_ck2
+
+  resets:
+    minItems: 3
+    maxItems: 3
+
+  reset-names:
+    items:
+      - const: pcie-rst0
+      - const: pcie-rst1
+      - const: pcie-rst2
+
+  phys:
+    minItems: 3
+    maxItems: 3
+
+  phy-names:
+    items:
+      - const: pcie-phy0
+      - const: pcie-phy1
+      - const: pcie-phy2
+
+  power-domains:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - ranges
+  - clocks
+  - clock-names
+  - '#interrupt-cells'
+  - resets
+  - reset-names
+  - phys
+  - phy-names
+  - power-domains
+  - pcie@0,0
+  - pcie@1,0
+  - pcie@2,0
+
+allOf:
+  - $ref: /schemas/pci/pci-host-bridge.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  # MT7623
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/clock/mt2701-clk.h>
+    #include <dt-bindings/reset/mt2701-resets.h>
+    #include <dt-bindings/phy/phy.h>
+    #include <dt-bindings/power/mt2701-power.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        pcie@1a140000 {
+            compatible = "mediatek,mt7623-pcie";
+            device_type = "pci";
+            reg = <0 0x1a140000 0 0x1000>, /* PCIe shared registers */
+                  <0 0x1a142000 0 0x1000>, /* Port0 registers */
+                  <0 0x1a143000 0 0x1000>, /* Port1 registers */
+                  <0 0x1a144000 0 0x1000>; /* Port2 registers */
+            reg-names = "subsys", "port0", "port1", "port2";
+            #address-cells = <3>;
+            #size-cells = <2>;
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0xf800 0 0 0>;
+            interrupt-map = <0x0000 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>,
+                            <0x0800 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>,
+                            <0x1000 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
+            clocks = <&topckgen CLK_TOP_ETHIF_SEL>,
+                    <&hifsys CLK_HIFSYS_PCIE0>,
+                    <&hifsys CLK_HIFSYS_PCIE1>,
+                    <&hifsys CLK_HIFSYS_PCIE2>;
+            clock-names = "free_ck", "sys_ck0", "sys_ck1", "sys_ck2";
+            resets = <&hifsys MT2701_HIFSYS_PCIE0_RST>,
+                     <&hifsys MT2701_HIFSYS_PCIE1_RST>,
+                     <&hifsys MT2701_HIFSYS_PCIE2_RST>;
+            reset-names = "pcie-rst0", "pcie-rst1", "pcie-rst2";
+            phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>,
+                   <&pcie2_phy PHY_TYPE_PCIE>;
+            phy-names = "pcie-phy0", "pcie-phy1", "pcie-phy2";
+            power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>;
+            bus-range = <0x00 0xff>;
+            ranges = <0x81000000 0 0x1a160000 0 0x1a160000 0 0x00010000>,	/* I/O space */
+                     <0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>;	/* memory space */
+
+            pcie@0,0 {
+                device_type = "pci";
+                reg = <0x0000 0 0 0 0>;
+                #address-cells = <3>;
+                #size-cells = <2>;
+                #interrupt-cells = <1>;
+                interrupt-map-mask = <0 0 0 0>;
+                interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>;
+                ranges;
+            };
+
+            pcie@1,0 {
+                device_type = "pci";
+                reg = <0x0800 0 0 0 0>;
+                #address-cells = <3>;
+                #size-cells = <2>;
+                #interrupt-cells = <1>;
+                interrupt-map-mask = <0 0 0 0>;
+                interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
+                ranges;
+            };
+
+            pcie@2,0 {
+                device_type = "pci";
+                reg = <0x1000 0 0 0 0>;
+                #address-cells = <3>;
+                #size-cells = <2>;
+                #interrupt-cells = <1>;
+                interrupt-map-mask = <0 0 0 0>;
+                interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
+                ranges;
+            };
+        };
+    };
Documentation/devicetree/bindings/pci/mediatek-pcie.txt deleted +0 -289

289 lines not on this page · raw message

Documentation/devicetree/bindings/pci/mediatek-pcie.yaml new file +318 -0

318 lines not on this page · raw message

Signature · 1 line
2.51.0
maintainer Reviewed-by on v5 2/5
#3 lore raw

Re: [PATCH v5 2/5] dt-bindings: PCI: mediatek: Convert to YAML schema

Quoted 12 lines · Christian Marangi

Convert the PCI mediatek Documentation to YAML schema to enable validation of the supported GEN1/2 Mediatek PCIe controller.

While converting, lots of cleanup were done from the .txt with better specifying what is supported by the various PCIe controller variant and drop of redundant info that are part of the standard PCIe Host Bridge schema.

To reduce schema complexity the .txt is split in 2 YAML, one for mt7623/mt2701 and the other for every other compatible.

Quoted 9 lines
---
 .../bindings/pci/mediatek-pcie-mt7623.yaml    | 164 +++++++++
 .../devicetree/bindings/pci/mediatek-pcie.txt | 289 ----------------
 .../bindings/pci/mediatek-pcie.yaml           | 318 ++++++++++++++++++
 3 files changed, 482 insertions(+), 289 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie-mt7623.yaml
 delete mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie.txt
 create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie.yaml
#4 lore raw

PATCH v5 3/5 dt-bindings: PCI: mediatek: Add support for Airoha AN7583

In reply to Christian Marangi

Introduce Airoha AN7583 SoC compatible in mediatek PCIe controller binding.

Similar to GEN3, the Airoha AN7583 GEN2 PCIe controller require the PBUS csr property to permit the correct functionality of the PCIe controller.

---
 .../bindings/pci/mediatek-pcie.yaml           | 120 ++++++++++++++++++
 1 file changed, 120 insertions(+)
Documentation/devicetree/bindings/pci/mediatek-pcie.yaml +120 -0
index fca6cb20d18b..0b8c78ec4f91 100644
@@ -13,6 +13,7 @@ properties:
   compatible:
     oneOf:
       - enum:
+          - airoha,an7583-pcie
           - mediatek,mt2712-pcie
           - mediatek,mt7622-pcie
           - mediatek,mt7629-pcie
@@ -40,6 +41,12 @@ properties:
       - enum: [ obff_ck0, obff_ck1 ]
       - enum: [ pipe_ck0, pipe_ck1 ]
 
+  resets:
+    maxItems: 1
+
+  reset-names:
+    const: pcie-rst1
+
   interrupts:
     maxItems: 1
 
@@ -55,6 +62,17 @@ properties:
   power-domains:
     maxItems: 1
 
+  mediatek,pbus-csr:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    items:
+      - items:
+          - description: phandle to pbus-csr syscon
+          - description: offset of pbus-csr base address register
+          - description: offset of pbus-csr base address mask register
+    description:
+      Phandle with two arguments to the syscon node used to detect if
+      a given address is accessible on PCIe controller.
+
   '#interrupt-cells':
     const: 1
 
@@ -90,6 +108,33 @@ required:
 allOf:
   - $ref: /schemas/pci/pci-host-bridge.yaml#
 
+  - if:
+      properties:
+        compatible:
+          const: airoha,an7583-pcie
+    then:
+      properties:
+        reg-names:
+          const: port1
+
+        clocks:
+          maxItems: 1
+
+        clock-names:
+          const: sys_ck1
+
+        phy-names:
+          const: pcie-phy1
+
+        power-domain: false
+
+      required:
+        - resets
+        - reset-names
+        - phys
+        - phy-names
+        - mediatek,pbus-csr
+
   - if:
       properties:
         compatible:
@@ -104,8 +149,14 @@ allOf:
           minItems: 2
           maxItems: 2
 
+        reset: false
+
+        reset-names: false
+
         power-domains: false
 
+        mediatek,pbus-csr: false
+
       required:
         - phys
         - phy-names
@@ -119,10 +170,16 @@ allOf:
         clocks:
           minItems: 6
 
+        reset: false
+
+        reset-names: false
+
         phys: false
 
         phy-names: false
 
+        mediatek,pbus-csr: false
+
       required:
         - power-domains
 
@@ -135,6 +192,12 @@ allOf:
         clocks:
           minItems: 6
 
+        reset: false
+
+        reset-names: false
+
+        mediatek,pbus-csr: false
+
       required:
         - power-domains
 
@@ -151,12 +214,18 @@ allOf:
         clock-names:
           maxItems: 1
 
+        reset: false
+
+        reset-names: false
+
         phys: false
 
         phy-names: false
 
         power-domain: false
 
+        mediatek,pbus-csr: false
+
 unevaluatedProperties: false
 
 examples:
@@ -316,3 +385,54 @@ examples:
             };
         };
     };
+
+  # AN7583
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/en7523-clk.h>
+
+    soc_3 {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        pcie@1fa92000 {
+            compatible = "airoha,an7583-pcie";
+            device_type = "pci";
+            linux,pci-domain = <1>;
+            #address-cells = <3>;
+            #size-cells = <2>;
+
+            reg = <0x0 0x1fa92000 0x0 0x1670>;
+            reg-names = "port1";
+
+            clocks = <&scuclk EN7523_CLK_PCIE>;
+            clock-names = "sys_ck1";
+
+            phys = <&pciephy>;
+            phy-names = "pcie-phy1";
+
+            ranges = <0x02000000 0 0x24000000 0x0 0x24000000 0 0x4000000>;
+
+            resets = <&scuclk>; /* AN7583_PCIE1_RST */
+            reset-names = "pcie-rst1";
+
+            mediatek,pbus-csr = <&pbus_csr 0x8 0xc>;
+
+            interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-names = "pcie_irq";
+            bus-range = <0x00 0xff>;
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0 0 0 7>;
+            interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+                            <0 0 0 2 &pcie_intc1 1>,
+                            <0 0 0 3 &pcie_intc1 2>,
+                            <0 0 0 4 &pcie_intc1 3>;
+
+            pcie_intc1_4: interrupt-controller {
+                interrupt-controller;
+                #address-cells = <0>;
+                #interrupt-cells = <1>;
+            };
+        };
+    };
Signature · 1 line
2.51.0
maintainer Reviewed-by on v5 3/5
#5 lore raw

Re: [PATCH v5 3/5] dt-bindings: PCI: mediatek: Add support for Airoha AN7583

Quoted 12 lines · Christian Marangi

Introduce Airoha AN7583 SoC compatible in mediatek PCIe controller binding.

Similar to GEN3, the Airoha AN7583 GEN2 PCIe controller require the PBUS csr property to permit the correct functionality of the PCIe controller.

---
 .../bindings/pci/mediatek-pcie.yaml           | 120 ++++++++++++++++++
 1 file changed, 120 insertions(+)
#6 lore raw

PATCH v5 4/5 PCI: mediatek: convert bool to single flags entry and bitmap

In reply to Christian Marangi

To clean Mediatek SoC PCIe struct, convert all the bool to a bitmap and use a single flags to reference all the values. This permits cleaner addition of new flag without having to define a new bool in the struct.

---
 drivers/pci/controller/pcie-mediatek.c | 28 +++++++++++++++-----------
 1 file changed, 16 insertions(+), 12 deletions(-)
drivers/pci/controller/pcie-mediatek.c +16 -12
index 24cc30a2ab6c..1678461e56d3 100644
@@ -142,24 +142,29 @@
 
 struct mtk_pcie_port;
 
+enum mtk_pcie_flags {
+	NEED_FIX_CLASS_ID = BIT(0), /* host's class ID needed to be fixed */
+	NEED_FIX_DEVICE_ID = BIT(1), /* host's device ID needed to be fixed */
+	NO_MSI = BIT(2), /* Bridge has no MSI support, and relies on an
+			  * external block
+			  */
+};
+
 /**
  * struct mtk_pcie_soc - differentiate between host generations
- * @need_fix_class_id: whether this host's class ID needed to be fixed or not
- * @need_fix_device_id: whether this host's device ID needed to be fixed or not
  * @no_msi: Bridge has no MSI support, and relies on an external block
  * @device_id: device ID which this host need to be fixed
  * @ops: pointer to configuration access functions
  * @startup: pointer to controller setting functions
  * @setup_irq: pointer to initialize IRQ functions
+ * @flags: pcie device flags.
  */
 struct mtk_pcie_soc {
-	bool need_fix_class_id;
-	bool need_fix_device_id;
-	bool no_msi;
 	unsigned int device_id;
 	struct pci_ops *ops;
 	int (*startup)(struct mtk_pcie_port *port);
 	int (*setup_irq)(struct mtk_pcie_port *port, struct device_node *node);
+	u32 flags;
 };
 
 /**
@@ -703,7 +708,7 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
 	writel(val, port->base + PCIE_RST_CTRL);
 
 	/* Set up vendor ID and class code */
-	if (soc->need_fix_class_id) {
+	if (soc->flags & NEED_FIX_CLASS_ID) {
 		val = PCI_VENDOR_ID_MEDIATEK;
 		writew(val, port->base + PCIE_CONF_VEND_ID);
 
@@ -711,7 +716,7 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
 		writew(val, port->base + PCIE_CONF_CLASS_ID);
 	}
 
-	if (soc->need_fix_device_id)
+	if (soc->flags & NEED_FIX_DEVICE_ID)
 		writew(soc->device_id, port->base + PCIE_CONF_DEVICE_ID);
 
 	/* 100ms timeout value should be enough for Gen1/2 training */
@@ -1099,7 +1104,7 @@ static int mtk_pcie_probe(struct platform_device *pdev)
 
 	host->ops = pcie->soc->ops;
 	host->sysdata = pcie;
-	host->msi_domain = pcie->soc->no_msi;
+	host->msi_domain = !!(pcie->soc->flags & NO_MSI);
 
 	err = pci_host_probe(host);
 	if (err)
@@ -1187,9 +1192,9 @@ static const struct dev_pm_ops mtk_pcie_pm_ops = {
 };
 
 static const struct mtk_pcie_soc mtk_pcie_soc_v1 = {
-	.no_msi = true,
 	.ops = &mtk_pcie_ops,
 	.startup = mtk_pcie_startup_port,
+	.flags = NO_MSI,
 };
 
 static const struct mtk_pcie_soc mtk_pcie_soc_mt2712 = {
@@ -1199,19 +1204,18 @@ static const struct mtk_pcie_soc mtk_pcie_soc_mt2712 = {
 };
 
 static const struct mtk_pcie_soc mtk_pcie_soc_mt7622 = {
-	.need_fix_class_id = true,
 	.ops = &mtk_pcie_ops_v2,
 	.startup = mtk_pcie_startup_port_v2,
 	.setup_irq = mtk_pcie_setup_irq,
+	.flags = NEED_FIX_CLASS_ID,
 };
 
 static const struct mtk_pcie_soc mtk_pcie_soc_mt7629 = {
-	.need_fix_class_id = true,
-	.need_fix_device_id = true,
 	.device_id = PCI_DEVICE_ID_MEDIATEK_7629,
 	.ops = &mtk_pcie_ops_v2,
 	.startup = mtk_pcie_startup_port_v2,
 	.setup_irq = mtk_pcie_setup_irq,
+	.flags = NEED_FIX_CLASS_ID | NEED_FIX_DEVICE_ID,
 };
 
 static const struct of_device_id mtk_pcie_ids[] = {
Signature · 1 line
2.51.0
#7 lore raw

Re: [PATCH v5 4/5] PCI: mediatek: convert bool to single flags entry and bitmap

Il 12/10/25 22:56, Christian Marangi ha scritto:

Quoted 14 lines

To clean Mediatek SoC PCIe struct, convert all the bool to a bitmap and use a single flags to reference all the values. This permits cleaner addition of new flag without having to define a new bool in the struct.

---
  drivers/pci/controller/pcie-mediatek.c | 28 +++++++++++++++-----------
  1 file changed, 16 insertions(+), 12 deletions(-)
drivers/pci/controller/pcie-mediatek.c +0 -0
index 24cc30a2ab6c..1678461e56d3 100644

drivers/pci/controller/pcie-mediatek.c line 145

Quoted 4 lines
drivers/pci/controller/pcie-mediatek.c +1 -0
@@ -142,24 +142,29 @@
 
  struct mtk_pcie_port;
 
+enum mtk_pcie_flags {

enum mtk_pcie_quirks seems to be a better fit here, as this is used for... well.. quirks.

drivers/pci/controller/pcie-mediatek.c line 150

Quoted 5 lines
drivers/pci/controller/pcie-mediatek.c +5 -0
+	NEED_FIX_CLASS_ID = BIT(0), /* host's class ID needed to be fixed */
+	NEED_FIX_DEVICE_ID = BIT(1), /* host's device ID needed to be fixed */
+	NO_MSI = BIT(2), /* Bridge has no MSI support, and relies on an
+			  * external block
+			  */

Also perhaps... MTK_PCIE_FIX_CLASS_ID, MTK_PCIE_FIX_DEV_ID, MTK_PCIE_NO_MSI

Quoted 12 lines
drivers/pci/controller/pcie-mediatek.c +3 -2
+};
+
  /**
   * struct mtk_pcie_soc - differentiate between host generations
- * @need_fix_class_id: whether this host's class ID needed to be fixed or not
- * @need_fix_device_id: whether this host's device ID needed to be fixed or not
   * @no_msi: Bridge has no MSI support, and relies on an external block
   * @device_id: device ID which this host need to be fixed
   * @ops: pointer to configuration access functions
   * @startup: pointer to controller setting functions
   * @setup_irq: pointer to initialize IRQ functions
+ * @flags: pcie device flags.

drivers/pci/controller/pcie-mediatek.c line 167

Quoted 10 lines
drivers/pci/controller/pcie-mediatek.c +1 -3
   */
  struct mtk_pcie_soc {
-	bool need_fix_class_id;
-	bool need_fix_device_id;
-	bool no_msi;
  	unsigned int device_id;
  	struct pci_ops *ops;
  	int (*startup)(struct mtk_pcie_port *port);
  	int (*setup_irq)(struct mtk_pcie_port *port, struct device_node *node);
+	u32 flags;

u32 flags -> enum mtk_pcie_quirks quirks

Cheers,
Angelo

Quoted 63 lines
drivers/pci/controller/pcie-mediatek.c +6 -7
  };
 
  /**
@@ -703,7 +708,7 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
  	writel(val, port->base + PCIE_RST_CTRL);
 
  	/* Set up vendor ID and class code */
-	if (soc->need_fix_class_id) {
+	if (soc->flags & NEED_FIX_CLASS_ID) {
  		val = PCI_VENDOR_ID_MEDIATEK;
  		writew(val, port->base + PCIE_CONF_VEND_ID);
 
@@ -711,7 +716,7 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
  		writew(val, port->base + PCIE_CONF_CLASS_ID);
  	}
 
-	if (soc->need_fix_device_id)
+	if (soc->flags & NEED_FIX_DEVICE_ID)
  		writew(soc->device_id, port->base + PCIE_CONF_DEVICE_ID);
 
  	/* 100ms timeout value should be enough for Gen1/2 training */
@@ -1099,7 +1104,7 @@ static int mtk_pcie_probe(struct platform_device *pdev)
 
  	host->ops = pcie->soc->ops;
  	host->sysdata = pcie;
-	host->msi_domain = pcie->soc->no_msi;
+	host->msi_domain = !!(pcie->soc->flags & NO_MSI);
 
  	err = pci_host_probe(host);
  	if (err)
@@ -1187,9 +1192,9 @@ static const struct dev_pm_ops mtk_pcie_pm_ops = {
  };
 
  static const struct mtk_pcie_soc mtk_pcie_soc_v1 = {
-	.no_msi = true,
  	.ops = &mtk_pcie_ops,
  	.startup = mtk_pcie_startup_port,
+	.flags = NO_MSI,
  };
 
  static const struct mtk_pcie_soc mtk_pcie_soc_mt2712 = {
@@ -1199,19 +1204,18 @@ static const struct mtk_pcie_soc mtk_pcie_soc_mt2712 = {
  };
 
  static const struct mtk_pcie_soc mtk_pcie_soc_mt7622 = {
-	.need_fix_class_id = true,
  	.ops = &mtk_pcie_ops_v2,
  	.startup = mtk_pcie_startup_port_v2,
  	.setup_irq = mtk_pcie_setup_irq,
+	.flags = NEED_FIX_CLASS_ID,
  };
 
  static const struct mtk_pcie_soc mtk_pcie_soc_mt7629 = {
-	.need_fix_class_id = true,
-	.need_fix_device_id = true,
  	.device_id = PCI_DEVICE_ID_MEDIATEK_7629,
  	.ops = &mtk_pcie_ops_v2,
  	.startup = mtk_pcie_startup_port_v2,
  	.setup_irq = mtk_pcie_setup_irq,
+	.flags = NEED_FIX_CLASS_ID | NEED_FIX_DEVICE_ID,
  };
 
  static const struct of_device_id mtk_pcie_ids[] = {
#8 lore raw

Re: [PATCH v5 4/5] PCI: mediatek: convert bool to single flags entry and bitmap

Quoted 21 lines · AngeloGioacchino Del Regno

Il 12/10/25 22:56, Christian Marangi ha scritto:

Quoted 14 lines

To clean Mediatek SoC PCIe struct, convert all the bool to a bitmap and use a single flags to reference all the values. This permits cleaner addition of new flag without having to define a new bool in the struct.

---
  drivers/pci/controller/pcie-mediatek.c | 28 +++++++++++++++-----------
  1 file changed, 16 insertions(+), 12 deletions(-)
drivers/pci/controller/pcie-mediatek.c +0 -0
index 24cc30a2ab6c..1678461e56d3 100644

drivers/pci/controller/pcie-mediatek.c line 143

Quoted 2 lines
drivers/pci/controller/pcie-mediatek.c +1 -0
@@ -142,24 +142,29 @@
  struct mtk_pcie_port;
+enum mtk_pcie_flags {

enum mtk_pcie_quirks seems to be a better fit here, as this is used for... well.. quirks.

Quoted 4 lines

drivers/pci/controller/pcie-mediatek.c line 149

Quoted 4 lines
drivers/pci/controller/pcie-mediatek.c +4 -0
+	NEED_FIX_CLASS_ID = BIT(0), /* host's class ID needed to be fixed */
+	NEED_FIX_DEVICE_ID = BIT(1), /* host's device ID needed to be fixed */
+	NO_MSI = BIT(2), /* Bridge has no MSI support, and relies on an
+			  * external block

Add comments as Kernel doc.

Quoted 11 lines

drivers/pci/controller/pcie-mediatek.c line 150

Quoted 1 line
drivers/pci/controller/pcie-mediatek.c +1 -0
+			  */

Also perhaps... MTK_PCIE_FIX_CLASS_ID, MTK_PCIE_FIX_DEV_ID, MTK_PCIE_NO_MSI

drivers/pci/controller/pcie-mediatek.c line 155

Quoted 7 lines
drivers/pci/controller/pcie-mediatek.c +2 -2
+};
+
  /**
   * struct mtk_pcie_soc - differentiate between host generations
- * @need_fix_class_id: whether this host's class ID needed to be fixed or not
- * @need_fix_device_id: whether this host's device ID needed to be fixed or not
   * @no_msi: Bridge has no MSI support, and relies on an external block

Forgot to remove @no_msi?

- Mani

Signature · 1 line
மணிவண்ணன் சதாசிவம்
#9 lore raw

PATCH v5 5/5 PCI: mediatek: add support for Airoha AN7583 SoC

In reply to Christian Marangi

Add support for the second PCIe Root Complex present on Airoha AN7583 SoC.

This is based on the Mediatek Gen1/2 PCIe driver and similar to Gen3 also require workaround for the reset signals.

Introduce a new flag to skip having to reset signals and also introduce some additional logic to configure the PBUS registers required for Airoha SoC.

While at it, also add additional info on the PERST# Signal delay comments and use dedicated macro.

---
 drivers/pci/controller/pcie-mediatek.c | 92 ++++++++++++++++++++------
 1 file changed, 70 insertions(+), 22 deletions(-)
drivers/pci/controller/pcie-mediatek.c +70 -22
index 1678461e56d3..3340c005da4b 100644
@@ -148,6 +148,7 @@ enum mtk_pcie_flags {
 	NO_MSI = BIT(2), /* Bridge has no MSI support, and relies on an
 			  * external block
 			  */
+	SKIP_PCIE_RSTB	= BIT(3), /* Skip calling RSTB bits on PCIe probe */
 };
 
 /**
@@ -684,28 +685,32 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
 		regmap_update_bits(pcie->cfg, PCIE_SYS_CFG_V2, val, val);
 	}
 
-	/* Assert all reset signals */
-	writel(0, port->base + PCIE_RST_CTRL);
-
-	/*
-	 * Enable PCIe link down reset, if link status changed from link up to
-	 * link down, this will reset MAC control registers and configuration
-	 * space.
-	 */
-	writel(PCIE_LINKDOWN_RST_EN, port->base + PCIE_RST_CTRL);
-
-	/*
-	 * Described in PCIe CEM specification sections 2.2 (PERST# Signal) and
-	 * 2.2.1 (Initial Power-Up (G3 to S0)). The deassertion of PERST# should
-	 * be delayed 100ms (TPVPERL) for the power and clock to become stable.
-	 */
-	msleep(100);
-
-	/* De-assert PHY, PE, PIPE, MAC and configuration reset	*/
-	val = readl(port->base + PCIE_RST_CTRL);
-	val |= PCIE_PHY_RSTB | PCIE_PERSTB | PCIE_PIPE_SRSTB |
-	       PCIE_MAC_SRSTB | PCIE_CRSTB;
-	writel(val, port->base + PCIE_RST_CTRL);
+	if (!(soc->flags & SKIP_PCIE_RSTB)) {
+		/* Assert all reset signals */
+		writel(0, port->base + PCIE_RST_CTRL);
+
+		/*
+		 * Enable PCIe link down reset, if link status changed from
+		 * link up to link down, this will reset MAC control registers
+		 * and configuration space.
+		 */
+		writel(PCIE_LINKDOWN_RST_EN, port->base + PCIE_RST_CTRL);
+
+		/*
+		 * Described in PCIe CEM specification revision 3.0 sections
+		 * 2.2 (PERST# Signal) and 2.2.1 (Initial Power-Up (G3 to S0)).
+		 *
+		 * The deassertion of PERST# should be delayed 100ms (TPVPERL)
+		 * for the power and clock to become stable.
+		 */
+		msleep(PCIE_T_PVPERL_MS);
+
+		/* De-assert PHY, PE, PIPE, MAC and configuration reset	*/
+		val = readl(port->base + PCIE_RST_CTRL);
+		val |= PCIE_PHY_RSTB | PCIE_PERSTB | PCIE_PIPE_SRSTB |
+		       PCIE_MAC_SRSTB | PCIE_CRSTB;
+		writel(val, port->base + PCIE_RST_CTRL);
+	}
 
 	/* Set up vendor ID and class code */
 	if (soc->flags & NEED_FIX_CLASS_ID) {
@@ -826,6 +831,41 @@ static int mtk_pcie_startup_port(struct mtk_pcie_port *port)
 	return 0;
 }
 
+static int mtk_pcie_startup_port_an7583(struct mtk_pcie_port *port)
+{
+	struct mtk_pcie *pcie = port->pcie;
+	struct device *dev = pcie->dev;
+	struct pci_host_bridge *host;
+	struct resource_entry *entry;
+	struct regmap *pbus_regmap;
+	resource_size_t addr;
+	u32 args[2], size;
+
+	/*
+	 * Configure PBus base address and base address mask to allow
+	 * the hw to detect if a given address is accessible on PCIe
+	 * controller.
+	 */
+	pbus_regmap = syscon_regmap_lookup_by_phandle_args(dev->of_node,
+							   "mediatek,pbus-csr",
+							   ARRAY_SIZE(args),
+							   args);
+	if (IS_ERR(pbus_regmap))
+		return PTR_ERR(pbus_regmap);
+
+	host = pci_host_bridge_from_priv(pcie);
+	entry = resource_list_first_type(&host->windows, IORESOURCE_MEM);
+	if (!entry)
+		return -ENODEV;
+
+	addr = entry->res->start - entry->offset;
+	regmap_write(pbus_regmap, args[0], lower_32_bits(addr));
+	size = lower_32_bits(resource_size(entry->res));
+	regmap_write(pbus_regmap, args[1], GENMASK(31, __fls(size)));
+
+	return mtk_pcie_startup_port_v2(port);
+}
+
 static void mtk_pcie_enable_port(struct mtk_pcie_port *port)
 {
 	struct mtk_pcie *pcie = port->pcie;
@@ -1210,6 +1250,13 @@ static const struct mtk_pcie_soc mtk_pcie_soc_mt7622 = {
 	.flags = NEED_FIX_CLASS_ID,
 };
 
+static const struct mtk_pcie_soc mtk_pcie_soc_an7583 = {
+	.ops = &mtk_pcie_ops_v2,
+	.startup = mtk_pcie_startup_port_an7583,
+	.setup_irq = mtk_pcie_setup_irq,
+	.flags = NEED_FIX_CLASS_ID | SKIP_PCIE_RSTB,
+};
+
 static const struct mtk_pcie_soc mtk_pcie_soc_mt7629 = {
 	.device_id = PCI_DEVICE_ID_MEDIATEK_7629,
 	.ops = &mtk_pcie_ops_v2,
@@ -1219,6 +1266,7 @@ static const struct mtk_pcie_soc mtk_pcie_soc_mt7629 = {
 };
 
 static const struct of_device_id mtk_pcie_ids[] = {
+	{ .compatible = "airoha,an7583-pcie", .data = &mtk_pcie_soc_an7583 },
 	{ .compatible = "mediatek,mt2701-pcie", .data = &mtk_pcie_soc_v1 },
 	{ .compatible = "mediatek,mt7623-pcie", .data = &mtk_pcie_soc_v1 },
 	{ .compatible = "mediatek,mt2712-pcie", .data = &mtk_pcie_soc_mt2712 },
Signature · 1 line
2.51.0
#10 lore raw

Re: [PATCH v5 5/5] PCI: mediatek: add support for Airoha AN7583 SoC

Quoted 6 lines · Christian Marangi

Add support for the second PCIe Root Complex present on Airoha AN7583 SoC.

This is based on the Mediatek Gen1/2 PCIe driver and similar to Gen3 also require workaround for the reset signals.

Quoted 7 lines

Introduce a new flag to skip having to reset signals and also introduce some additional logic to configure the PBUS registers required for Airoha SoC.

While at it, also add additional info on the PERST# Signal delay comments and use dedicated macro.

This belongs to a separate patch which should come before this one.

Quoted 50 lines
---
 drivers/pci/controller/pcie-mediatek.c | 92 ++++++++++++++++++++------
 1 file changed, 70 insertions(+), 22 deletions(-)
drivers/pci/controller/pcie-mediatek.c +8 -22
index 1678461e56d3..3340c005da4b 100644
@@ -148,6 +148,7 @@ enum mtk_pcie_flags {
 	NO_MSI = BIT(2), /* Bridge has no MSI support, and relies on an
 			  * external block
 			  */
+	SKIP_PCIE_RSTB	= BIT(3), /* Skip calling RSTB bits on PCIe probe */
 };
 
 /**
@@ -684,28 +685,32 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
 		regmap_update_bits(pcie->cfg, PCIE_SYS_CFG_V2, val, val);
 	}
 
-	/* Assert all reset signals */
-	writel(0, port->base + PCIE_RST_CTRL);
-
-	/*
-	 * Enable PCIe link down reset, if link status changed from link up to
-	 * link down, this will reset MAC control registers and configuration
-	 * space.
-	 */
-	writel(PCIE_LINKDOWN_RST_EN, port->base + PCIE_RST_CTRL);
-
-	/*
-	 * Described in PCIe CEM specification sections 2.2 (PERST# Signal) and
-	 * 2.2.1 (Initial Power-Up (G3 to S0)). The deassertion of PERST# should
-	 * be delayed 100ms (TPVPERL) for the power and clock to become stable.
-	 */
-	msleep(100);
-
-	/* De-assert PHY, PE, PIPE, MAC and configuration reset	*/
-	val = readl(port->base + PCIE_RST_CTRL);
-	val |= PCIE_PHY_RSTB | PCIE_PERSTB | PCIE_PIPE_SRSTB |
-	       PCIE_MAC_SRSTB | PCIE_CRSTB;
-	writel(val, port->base + PCIE_RST_CTRL);
+	if (!(soc->flags & SKIP_PCIE_RSTB)) {
+		/* Assert all reset signals */
+		writel(0, port->base + PCIE_RST_CTRL);
+
+		/*
+		 * Enable PCIe link down reset, if link status changed from
+		 * link up to link down, this will reset MAC control registers

drivers/pci/controller/pcie-mediatek.c static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port) · line 704

Quoted 10 lines
drivers/pci/controller/pcie-mediatek.c +10 -0
+		 * and configuration space.
+		 */
+		writel(PCIE_LINKDOWN_RST_EN, port->base + PCIE_RST_CTRL);
+
+		/*
+		 * Described in PCIe CEM specification revision 3.0 sections
+		 * 2.2 (PERST# Signal) and 2.2.1 (Initial Power-Up (G3 to S0)).
+		 *
+		 * The deassertion of PERST# should be delayed 100ms (TPVPERL)
+		 * for the power and clock to become stable.

You can drop the comments since PCIE_T_PVPERL_MS definition has them.

drivers/pci/controller/pcie-mediatek.c static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port) · line 712

Quoted 8 lines
drivers/pci/controller/pcie-mediatek.c +8 -0
+		 */
+		msleep(PCIE_T_PVPERL_MS);
+
+		/* De-assert PHY, PE, PIPE, MAC and configuration reset	*/
+		val = readl(port->base + PCIE_RST_CTRL);
+		val |= PCIE_PHY_RSTB | PCIE_PERSTB | PCIE_PIPE_SRSTB |
+		       PCIE_MAC_SRSTB | PCIE_CRSTB;
+		writel(val, port->base + PCIE_RST_CTRL);

If PCIE_LINKDOWN_RST_EN corresponds to PERST# signal, then it should be deasserted only after the power and REFCLK are stable. But I'm not sure what the above PCIE_RST_CTRL setting is doing. If it somehow affects either power or REFCLK, then it should come before PCIE_LINKDOWN_RST_EN.

- Mani

Signature · 1 line
மணிவண்ணன் சதாசிவம்
#11 lore raw

Re: [PATCH v5 5/5] PCI: mediatek: add support for Airoha AN7583 SoC

Quoted 80 lines · Manivannan Sadhasivam
Quoted 6 lines · Christian Marangi

Add support for the second PCIe Root Complex present on Airoha AN7583 SoC.

This is based on the Mediatek Gen1/2 PCIe driver and similar to Gen3 also require workaround for the reset signals.

Quoted 7 lines

Introduce a new flag to skip having to reset signals and also introduce some additional logic to configure the PBUS registers required for Airoha SoC.

While at it, also add additional info on the PERST# Signal delay comments and use dedicated macro.

This belongs to a separate patch which should come before this one.

Quoted 50 lines
---
 drivers/pci/controller/pcie-mediatek.c | 92 ++++++++++++++++++++------
 1 file changed, 70 insertions(+), 22 deletions(-)
drivers/pci/controller/pcie-mediatek.c +8 -22
index 1678461e56d3..3340c005da4b 100644
@@ -148,6 +148,7 @@ enum mtk_pcie_flags {
 	NO_MSI = BIT(2), /* Bridge has no MSI support, and relies on an
 			  * external block
 			  */
+	SKIP_PCIE_RSTB	= BIT(3), /* Skip calling RSTB bits on PCIe probe */
 };
 
 /**
@@ -684,28 +685,32 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
 		regmap_update_bits(pcie->cfg, PCIE_SYS_CFG_V2, val, val);
 	}
 
-	/* Assert all reset signals */
-	writel(0, port->base + PCIE_RST_CTRL);
-
-	/*
-	 * Enable PCIe link down reset, if link status changed from link up to
-	 * link down, this will reset MAC control registers and configuration
-	 * space.
-	 */
-	writel(PCIE_LINKDOWN_RST_EN, port->base + PCIE_RST_CTRL);
-
-	/*
-	 * Described in PCIe CEM specification sections 2.2 (PERST# Signal) and
-	 * 2.2.1 (Initial Power-Up (G3 to S0)). The deassertion of PERST# should
-	 * be delayed 100ms (TPVPERL) for the power and clock to become stable.
-	 */
-	msleep(100);
-
-	/* De-assert PHY, PE, PIPE, MAC and configuration reset	*/
-	val = readl(port->base + PCIE_RST_CTRL);
-	val |= PCIE_PHY_RSTB | PCIE_PERSTB | PCIE_PIPE_SRSTB |
-	       PCIE_MAC_SRSTB | PCIE_CRSTB;
-	writel(val, port->base + PCIE_RST_CTRL);
+	if (!(soc->flags & SKIP_PCIE_RSTB)) {
+		/* Assert all reset signals */
+		writel(0, port->base + PCIE_RST_CTRL);
+
+		/*
+		 * Enable PCIe link down reset, if link status changed from
+		 * link up to link down, this will reset MAC control registers

drivers/pci/controller/pcie-mediatek.c static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port) · line 704

Quoted 10 lines
drivers/pci/controller/pcie-mediatek.c +10 -0
+		 * and configuration space.
+		 */
+		writel(PCIE_LINKDOWN_RST_EN, port->base + PCIE_RST_CTRL);
+
+		/*
+		 * Described in PCIe CEM specification revision 3.0 sections
+		 * 2.2 (PERST# Signal) and 2.2.1 (Initial Power-Up (G3 to S0)).
+		 *
+		 * The deassertion of PERST# should be delayed 100ms (TPVPERL)
+		 * for the power and clock to become stable.

You can drop the comments since PCIE_T_PVPERL_MS definition has them.

Quoted 14 lines

drivers/pci/controller/pcie-mediatek.c static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port) · line 712

Quoted 8 lines
drivers/pci/controller/pcie-mediatek.c +8 -0
+		 */
+		msleep(PCIE_T_PVPERL_MS);
+
+		/* De-assert PHY, PE, PIPE, MAC and configuration reset	*/
+		val = readl(port->base + PCIE_RST_CTRL);
+		val |= PCIE_PHY_RSTB | PCIE_PERSTB | PCIE_PIPE_SRSTB |
+		       PCIE_MAC_SRSTB | PCIE_CRSTB;
+		writel(val, port->base + PCIE_RST_CTRL);

If PCIE_LINKDOWN_RST_EN corresponds to PERST# signal, then it should be deasserted only after the power and REFCLK are stable. But I'm not sure what the above PCIE_RST_CTRL setting is doing. If it somehow affects either power or REFCLK, then it should come before PCIE_LINKDOWN_RST_EN.

Hi I checked MT7622 programming guide for this.

The order of operation for reset is exactly what you have described.

Indded, first everything is reset (assert all signals) then we set PCIE_LINKDOWN_RST_EN that in unrelated. We wait for clock stabilization with the msleep and only AFTER we deassert the PCIE_PERSTB.

So no, PCIE_LINKDOWN_RST_EN is not PERST# signal sw but it's actually PCIE_PERSTB.

Quoted 3 lines
Signature · 2 lines
-- 
மணிவண்ணன் சதாசிவம்
Signature · 1 line
	Ansuel
maintainer Applied
#12 lore raw

Re: (subset) [PATCH v5 0/5] PCI: mediatek: add support AN7583 + YAML rework

In reply to Christian Marangi
Quoted 20 lines · Christian Marangi

This little series convert the PCIe GEN2 Documentation to YAML schema and adds support for Airoha AN7583 GEN2 PCIe Controller.

Changes v5:
- Drop redudant entry from AN7583 patch
- Fix YAML error for AN7583 patch (sorry) Changes v4:
- Additional fix/improvement for YAML conversion
- Add review tag
- Fix wording on hifsys patch
- Rework PCI driver to flags and improve PBus logic Changes v3:
- Rework patch 1 to drop syscon compatible Changes v2:
- Add cover letter
- Describe skip_pcie_rstb variable
- Fix hifsys schema (missing syscon)
- Address comments on the YAML schema for PCIe GEN2
- Keep alphabetical order for AN7583

Quoted 1 line

[...]

Applied to v6.18-next/dts32, thanks!

[1/5] ARM: dts: mediatek: drop wrong syscon hifsys compatible for MT2701/7623

      commit: 5416aeee4ef761b79d2e1c35f6d9a35bf3104709

Cheers,
Angelo

#13 lore raw
In reply to Christian Marangi
Quoted 10 lines · Christian Marangi

This little series convert the PCIe GEN2 Documentation to YAML schema and adds support for Airoha AN7583 GEN2 PCIe Controller.

Christian Marangi (5):
ARM: dts: mediatek: drop wrong syscon hifsys compatible for

    MT2701/7623

dt-bindings: PCI: mediatek: Convert to YAML schema
dt-bindings: PCI: mediatek: Add support for Airoha AN7583
PCI: mediatek: convert bool to single flags entry and bitmap
PCI: mediatek: add support for Airoha AN7583 SoC

If you repost,

s/convert bool/Convert bool/
s/add support/Add support/

to match the history (use "git log --oneline drivers/pci/controller/pcie-mediatek.c" to see it).