Skip to contentSkip to conversation

5.10.246-rc1 review

PATCH In review Greg Kroah-Hartman 9 participants 344 messages Oct 27, 2025 – Nov 6, 2025 Page 2 of 3

Subsystems (4)
lore
Share & tools
lore
author maintainer
#170 lore raw

PATCH 168/332 ext4: increase i_disksize to offset + len in ext4_update_disksize_before_punch()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Yongjian Sun <[email protected]>

commit 9d80eaa1a1d37539224982b76c9ceeee736510b9 upstream.

After running a stress test combined with fault injection, we performed fsck -a followed by fsck -fn on the filesystem image. During the second pass, fsck -fn reported:

Inode 131512, end of extent exceeds allowed value

	(logical block 405, physical block 1180540, len 2)

This inode was not in the orphan list. Analysis revealed the following call chain that leads to the inconsistency:

                             ext4_da_write_end()
                              //does not update i_disksize
                             ext4_punch_hole()
                              //truncate folio, keep size
ext4_page_mkwrite()
 ext4_block_page_mkwrite()
  ext4_block_write_begin()
    ext4_get_block()
     //insert written extent without update i_disksize

journal commit
echo 1 > /sys/block/xxx/device/delete

da-write path updates i_size but does not update i_disksize. Then ext4_punch_hole truncates the da-folio yet still leaves i_disksize unchanged(in the ext4_update_disksize_before_punch function, the condition offset + len < size is met). Then ext4_page_mkwrite sees ext4_nonda_switch return 1 and takes the nodioread_nolock path, the folio about to be written has just been punched out, and it’s offset sits beyond the current i_disksize. This may result in a written extent being inserted, but again does not update i_disksize. If the journal gets committed and then the block device is yanked, we might run into this. It should be noted that replacing ext4_punch_hole with ext4_zero_range in the call sequence may also trigger this issue, as neither will update i_disksize under these circumstances.

To fix this, we can modify ext4_update_disksize_before_punch to increase i_disksize to min(i_size, offset + len) when both i_size and (offset + len) are greater than i_disksize.

Message-ID: <[email protected]>

---
 fs/ext4/inode.c |   10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)
fs/ext4/inode.c +8 -2
@@ -3991,7 +3991,11 @@ int ext4_can_truncate(struct inode *inod
  * We have to make sure i_disksize gets properly updated before we truncate
  * page cache due to hole punching or zero range. Otherwise i_disksize update
  * can get lost as it may have been postponed to submission of writeback but
- * that will never happen after we truncate page cache.
+ * that will never happen if we remove the folio containing i_size from the
+ * page cache. Also if we punch hole within i_size but above i_disksize,
+ * following ext4_page_mkwrite() may mistakenly allocate written blocks over
+ * the hole and thus introduce allocated blocks beyond i_disksize which is
+ * not allowed (e2fsck would complain in case of crash).
  */
 int ext4_update_disksize_before_punch(struct inode *inode, loff_t offset,
 				      loff_t len)
@@ -4002,9 +4006,11 @@ int ext4_update_disksize_before_punch(st
 	loff_t size = i_size_read(inode);
 
 	WARN_ON(!inode_is_locked(inode));
-	if (offset > size || offset + len < size)
+	if (offset > size)
 		return 0;
 
+	if (offset + len < size)
+		size = offset + len;
 	if (EXT4_I(inode)->i_disksize >= size)
 		return 0;
 
author maintainer
#171 lore raw

PATCH 169/332 ext4: correctly handle queries for metadata mappings

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Ojaswin Mujoo <[email protected]>

commit 46c22a8bb4cb03211da1100d7ee4a2005bf77c70 upstream.

Currently, our handling of metadata is _ambiguous_ in some scenarios, that is, we end up returning unknown if the range only covers the mapping partially.

For example, in the following case:

$ xfs_io -c fsmap -d

0: 254:16 [0..7]: static fs metadata 8
1: 254:16 [8..15]: special 102:1 8
2: 254:16 [16..5127]: special 102:2 5112
3: 254:16 [5128..5255]: special 102:3 128
4: 254:16 [5256..5383]: special 102:4 128
5: 254:16 [5384..70919]: inodes 65536
6: 254:16 [70920..70967]: unknown 48
...

$ xfs_io -c fsmap -d 24 33

0: 254:16 [24..39]: unknown 16 <--- incomplete reporting

$ xfs_io -c fsmap -d 24 33  (With patch)
    0: 254:16 [16..5127]: special 102:2 5112

This is because earlier in ext4_getfsmap_meta_helper, we end up ignoring any extent that starts before our queried range, but overlaps it. While the man page [1] is a bit ambiguous on this, this fix makes the output make more sense since we are anyways returning an "unknown" extent. This is also consistent to how XFS does it:

$ xfs_io -c fsmap -d

...
6: 254:16 [104..127]: free space 24
7: 254:16 [128..191]: inodes 64
...

$ xfs_io -c fsmap -d 137 150

0: 254:16 [128..191]: inodes 64 <-- full extent returned

[1] https://man7.org/linux/man-pages/man2/ioctl_getfsmap.2.html

Message-ID: <023f37e35ee280cd9baac0296cbadcbe10995cab.1757058211.git.ojaswin@linux.ibm.com>

---
 fs/ext4/fsmap.c |   14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
fs/ext4/fsmap.c +9 -5
@@ -74,7 +74,8 @@ static int ext4_getfsmap_dev_compare(con
 static bool ext4_getfsmap_rec_before_low_key(struct ext4_getfsmap_info *info,
 					     struct ext4_fsmap *rec)
 {
-	return rec->fmr_physical < info->gfi_low.fmr_physical;
+	return rec->fmr_physical + rec->fmr_length <=
+	       info->gfi_low.fmr_physical;
 }
 
 /*
@@ -200,15 +201,18 @@ static int ext4_getfsmap_meta_helper(str
 			  ext4_group_first_block_no(sb, agno));
 	fs_end = fs_start + EXT4_C2B(sbi, len);
 
-	/* Return relevant extents from the meta_list */
+	/*
+	 * Return relevant extents from the meta_list. We emit all extents that
+	 * partially/fully overlap with the query range
+	 */
 	list_for_each_entry_safe(p, tmp, &info->gfi_meta_list, fmr_list) {
-		if (p->fmr_physical < info->gfi_next_fsblk) {
+		if (p->fmr_physical + p->fmr_length <= info->gfi_next_fsblk) {
 			list_del(&p->fmr_list);
 			kfree(p);
 			continue;
 		}
-		if (p->fmr_physical <= fs_start ||
-		    p->fmr_physical + p->fmr_length <= fs_end) {
+		if (p->fmr_physical <= fs_end &&
+		    p->fmr_physical + p->fmr_length > fs_start) {
 			/* Emit the retained free extent record if present */
 			if (info->gfi_lastfree.fmr_owner) {
 				error = ext4_getfsmap_helper(sb, info,
author maintainer
#172 lore raw

PATCH 170/332 ext4: guard against EA inode refcount underflow in xattr update

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Ahmet Eray Karadag <[email protected]>

commit 57295e835408d8d425bef58da5253465db3d6888 upstream.

syzkaller found a path where ext4_xattr_inode_update_ref() reads an EA inode refcount that is already <= 0 and then applies ref_change (often -1). That lets the refcount underflow and we proceed with a bogus value, triggering errors like:

EXT4-fs error: EA inode <n> ref underflow: ref_count=-1 ref_change=-1 EXT4-fs warning: ea_inode dec ref err=-117

Make the invariant explicit: if the current refcount is non-positive, treat this as on-disk corruption, emit ext4_error_inode(), and fail the operation with -EFSCORRUPTED instead of updating the refcount. Delete the WARN_ONCE() as negative refcounts are now impossible; keep error reporting in ext4_error_inode().

This prevents the underflow and the follow-on orphan/cleanup churn.

Message-ID: <[email protected]>

---
 fs/ext4/xattr.c |   15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)
fs/ext4/xattr.c +8 -7
@@ -983,7 +983,7 @@ static int ext4_xattr_inode_update_ref(h
 				       int ref_change)
 {
 	struct ext4_iloc iloc;
-	s64 ref_count;
+	u64 ref_count;
 	int ret;
 
 	inode_lock_nested(ea_inode, I_MUTEX_XATTR);
@@ -993,13 +993,17 @@ static int ext4_xattr_inode_update_ref(h
 		goto out;
 
 	ref_count = ext4_xattr_inode_get_ref(ea_inode);
+	if ((ref_count == 0 && ref_change < 0) || (ref_count == U64_MAX && ref_change > 0)) {
+		ext4_error_inode(ea_inode, __func__, __LINE__, 0,
+			"EA inode %lu ref wraparound: ref_count=%lld ref_change=%d",
+			ea_inode->i_ino, ref_count, ref_change);
+		ret = -EFSCORRUPTED;
+		goto out;
+	}
 	ref_count += ref_change;
 	ext4_xattr_inode_set_ref(ea_inode, ref_count);
 
 	if (ref_change > 0) {
-		WARN_ONCE(ref_count <= 0, "EA inode %lu ref_count=%lld",
-			  ea_inode->i_ino, ref_count);
-
 		if (ref_count == 1) {
 			WARN_ONCE(ea_inode->i_nlink, "EA inode %lu i_nlink=%u",
 				  ea_inode->i_ino, ea_inode->i_nlink);
@@ -1008,9 +1012,6 @@ static int ext4_xattr_inode_update_ref(h
 			ext4_orphan_del(handle, ea_inode);
 		}
 	} else {
-		WARN_ONCE(ref_count < 0, "EA inode %lu ref_count=%lld",
-			  ea_inode->i_ino, ref_count);
-
 		if (ref_count == 0) {
 			WARN_ONCE(ea_inode->i_nlink != 1,
 				  "EA inode %lu i_nlink=%u",
author maintainer
#173 lore raw

PATCH 171/332 lib/crypto/curve25519-hacl64: Disable KASAN with clang-17 and older

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nathan Chancellor <[email protected]>

commit 2f13daee2a72bb962f5fd356c3a263a6f16da965 upstream.

After commit 6f110a5e4f99 ("Disable SLUB_TINY for build testing"), which causes CONFIG_KASAN to be enabled in allmodconfig again, arm64 allmodconfig builds with clang-17 and older show an instance of -Wframe-larger-than (which breaks the build with CONFIG_WERROR=y):

lib/crypto/curve25519-hacl64.c:757:6: error: stack frame size (2336) exceeds limit (2048) in 'curve25519_generic' [-Werror,-Wframe-larger-than]

    757 | void curve25519_generic(u8 mypublic[CURVE25519_KEY_SIZE],
        |      ^

When KASAN is disabled, the stack usage is roughly quartered:

lib/crypto/curve25519-hacl64.c:757:6: error: stack frame size (608) exceeds limit (128) in 'curve25519_generic' [-Werror,-Wframe-larger-than]

    757 | void curve25519_generic(u8 mypublic[CURVE25519_KEY_SIZE],
        |      ^

Using '-Rpass-analysis=stack-frame-layout' shows the following variables and many, many 8-byte spills when KASAN is enabled:

Offset: [SP-144], Type: Variable, Align: 8, Size: 40
Offset: [SP-464], Type: Variable, Align: 8, Size: 320
Offset: [SP-784], Type: Variable, Align: 8, Size: 320
Offset: [SP-864], Type: Variable, Align: 32, Size: 80
Offset: [SP-896], Type: Variable, Align: 32, Size: 32
Offset: [SP-1016], Type: Variable, Align: 8, Size: 120

When KASAN is disabled, there are still spills but not at many and the variables list is smaller:

Offset: [SP-192], Type: Variable, Align: 32, Size: 80
Offset: [SP-224], Type: Variable, Align: 32, Size: 32
Offset: [SP-344], Type: Variable, Align: 8, Size: 120

Disable KASAN for this file when using clang-17 or older to avoid blowing out the stack, clearing up the warning.

---
 lib/crypto/Makefile |    4 ++++
 1 file changed, 4 insertions(+)
lib/crypto/Makefile +4 -0
@@ -22,6 +22,10 @@ obj-$(CONFIG_CRYPTO_LIB_CURVE25519_GENER
 libcurve25519-generic-y				:= curve25519-fiat32.o
 libcurve25519-generic-$(CONFIG_ARCH_SUPPORTS_INT128)	:= curve25519-hacl64.o
 libcurve25519-generic-y				+= curve25519-generic.o
+# clang versions prior to 18 may blow out the stack with KASAN
+ifeq ($(call clang-min-version, 180000),)
+KASAN_SANITIZE_curve25519-hacl64.o := n
+endif
 
 obj-$(CONFIG_CRYPTO_LIB_CURVE25519)		+= libcurve25519.o
 libcurve25519-y					+= curve25519.o
#174 lore raw

Re: [PATCH 5.10 171/332] lib/crypto/curve25519-hacl64: Disable KASAN with clang-17 and older

Quoted 7 lines · Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nathan Chancellor <[email protected]>

commit 2f13daee2a72bb962f5fd356c3a263a6f16da965 upstream.

[...]

lib/crypto/Makefile obj-$(CONFIG_CRYPTO_LIB_CURVE25519_GENER · line 26

Quoted 8 lines
lib/crypto/Makefile +2 -0
@@ -22,6 +22,10 @@ obj-$(CONFIG_CRYPTO_LIB_CURVE25519_GENER
 libcurve25519-generic-y				:= curve25519-fiat32.o
 libcurve25519-generic-$(CONFIG_ARCH_SUPPORTS_INT128)	:= curve25519-hacl64.o
 libcurve25519-generic-y				+= curve25519-generic.o
+# clang versions prior to 18 may blow out the stack with KASAN
+ifeq ($(call clang-min-version, 180000),)

[...]

The clang-min-version macro isn't defined in 5.10 or 5.15, so this test doesn't work as intended.

Ben.

Signature · 4 lines
Ben Hutchings
The obvious mathematical breakthrough [to break modern encryption]
would be development of an easy way to factor large prime numbers.
                                                           - Bill Gates
author maintainer
#175 lore raw

Re: [PATCH 5.10 171/332] lib/crypto/curve25519-hacl64: Disable KASAN with clang-17 and older

Quoted 19 lines · Ben Hutchings
Quoted 7 lines · Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nathan Chancellor <[email protected]>

commit 2f13daee2a72bb962f5fd356c3a263a6f16da965 upstream.

[...]

Quoted 8 lines
lib/crypto/Makefile +2 -0
@@ -22,6 +22,10 @@ obj-$(CONFIG_CRYPTO_LIB_CURVE25519_GENER
 libcurve25519-generic-y				:= curve25519-fiat32.o
 libcurve25519-generic-$(CONFIG_ARCH_SUPPORTS_INT128)	:= curve25519-hacl64.o
 libcurve25519-generic-y				+= curve25519-generic.o
+# clang versions prior to 18 may blow out the stack with KASAN
+ifeq ($(call clang-min-version, 180000),)

[...]

Quoted 2 lines

The clang-min-version macro isn't defined in 5.10 or 5.15, so this test doesn't work as intended.

So should I revert it?

thanks,

greg k-h

#176 lore raw

Re: [PATCH 5.10 171/332] lib/crypto/curve25519-hacl64: Disable KASAN with clang-17 and older

Quoted 20 lines · Greg Kroah-Hartman
Quoted 19 lines · Ben Hutchings
Quoted 7 lines · Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nathan Chancellor <[email protected]>

commit 2f13daee2a72bb962f5fd356c3a263a6f16da965 upstream.

[...]

Quoted 8 lines
lib/crypto/Makefile +2 -0
@@ -22,6 +22,10 @@ obj-$(CONFIG_CRYPTO_LIB_CURVE25519_GENER
 libcurve25519-generic-y				:= curve25519-fiat32.o
 libcurve25519-generic-$(CONFIG_ARCH_SUPPORTS_INT128)	:= curve25519-hacl64.o
 libcurve25519-generic-y				+= curve25519-generic.o
+# clang versions prior to 18 may blow out the stack with KASAN
+ifeq ($(call clang-min-version, 180000),)

[...]

Quoted 4 lines
Quoted 2 lines

The clang-min-version macro isn't defined in 5.10 or 5.15, so this test doesn't work as intended.

So should I revert it?

No, we should backport clang-min-version and friends because these macros may be used in future backports. It should not be too hard. I can work on that tomorrow.

Additionally, now that I am looking at this change again, this disables KASAN for this file with GCC because clang-min-version will always evaluate to nothing for GCC. I'll send a fix for this upstream then it can be backported later.

Cheers,
Nathan

author maintainer
#177 lore raw

PATCH 172/332 arm64: dts: qcom: sdm845: Fix slimbam num-channels/ees

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Stephan Gerhold <[email protected]>

[ Upstream commit 316294bb6695a43a9181973ecd4e6fb3e576a9f7 ]

Reading the hardware registers of the &slimbam on RB3 reveals that the BAM supports only 23 pipes (channels) and supports 4 EEs instead of 2. This hasn't caused problems so far since nothing is using the extra channels, but attempting to use them would lead to crashes.

The bam_dma driver might warn in the future if the num-channels in the DT are wrong, so correct the properties in the DT to avoid future regressions.

---
 arch/arm64/boot/dts/qcom/sdm845.dtsi |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/qcom/sdm845.dtsi +2 -2
@@ -4492,11 +4492,11 @@
 			compatible = "qcom,bam-v1.7.0";
 			qcom,controlled-remotely;
 			reg = <0 0x17184000 0 0x2a000>;
-			num-channels  = <31>;
+			num-channels = <23>;
 			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
 			qcom,ee = <1>;
-			qcom,num-ees = <2>;
+			qcom,num-ees = <4>;
 			iommus = <&apps_smmu 0x1806 0x0>;
 		};
 
author maintainer
#178 lore raw

PATCH 173/332 tracing: Fix race condition in kprobe initialization causing NULL pointer dereference

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Yuan Chen <[email protected]>

[ Upstream commit 9cf9aa7b0acfde7545c1a1d912576e9bab28dc6f ]

There is a critical race condition in kprobe initialization that can lead to NULL pointer dereference and kernel crash.

[1135630.084782] Unable to handle kernel paging request at virtual address 0000710a04630000
...
[1135630.260314] pstate: 404003c9 (nZcv DAIF +PAN -UAO)
[1135630.269239] pc : kprobe_perf_func+0x30/0x260
[1135630.277643] lr : kprobe_dispatcher+0x44/0x60
[1135630.286041] sp : ffffaeff4977fa40
[1135630.293441] x29: ffffaeff4977fa40 x28: ffffaf015340e400
[1135630.302837] x27: 0000000000000000 x26: 0000000000000000
[1135630.312257] x25: ffffaf029ed108a8 x24: ffffaf015340e528
[1135630.321705] x23: ffffaeff4977fc50 x22: ffffaeff4977fc50
[1135630.331154] x21: 0000000000000000 x20: ffffaeff4977fc50
[1135630.340586] x19: ffffaf015340e400 x18: 0000000000000000
[1135630.349985] x17: 0000000000000000 x16: 0000000000000000
[1135630.359285] x15: 0000000000000000 x14: 0000000000000000
[1135630.368445] x13: 0000000000000000 x12: 0000000000000000
[1135630.377473] x11: 0000000000000000 x10: 0000000000000000
[1135630.386411] x9 : 0000000000000000 x8 : 0000000000000000
[1135630.395252] x7 : 0000000000000000 x6 : 0000000000000000
[1135630.403963] x5 : 0000000000000000 x4 : 0000000000000000
[1135630.412545] x3 : 0000710a04630000 x2 : 0000000000000006
[1135630.421021] x1 : ffffaeff4977fc50 x0 : 0000710a04630000
[1135630.429410] Call trace:
[1135630.434828]  kprobe_perf_func+0x30/0x260
[1135630.441661]  kprobe_dispatcher+0x44/0x60
[1135630.448396]  aggr_pre_handler+0x70/0xc8
[1135630.454959]  kprobe_breakpoint_handler+0x140/0x1e0
[1135630.462435]  brk_handler+0xbc/0xd8
[1135630.468437]  do_debug_exception+0x84/0x138
[1135630.475074]  el1_dbg+0x18/0x8c
[1135630.480582]  security_file_permission+0x0/0xd0
[1135630.487426]  vfs_write+0x70/0x1c0
[1135630.493059]  ksys_write+0x5c/0xc8
[1135630.498638]  __arm64_sys_write+0x24/0x30
[1135630.504821]  el0_svc_common+0x78/0x130
[1135630.510838]  el0_svc_handler+0x38/0x78
[1135630.516834]  el0_svc+0x8/0x1b0

kernel/trace/trace_kprobe.c: 1308
0xffff3df8995039ec <kprobe_perf_func+0x2c>: ldr x21, [x24,#120]
include/linux/compiler.h: 294
0xffff3df8995039f0 <kprobe_perf_func+0x30>: ldr x1, [x21,x0]

kernel/trace/trace_kprobe.c
1308: head = this_cpu_ptr(call->perf_events);
1309: if (hlist_empty(head))
1310: return 0;

crash> struct trace_event_call -o
struct trace_event_call {
...
[120] struct hlist_head *perf_events; //(call->perf_event)
...
}

crash> struct trace_event_call ffffaf015340e528
struct trace_event_call {
...
perf_events = 0xffff0ad5fa89f088, //this value is correct, but x21 = 0
...
}

Race Condition Analysis:

The race occurs between kprobe activation and perf_events initialization:

CPU0 CPU1
==== ====
perf_kprobe_init

    perf_trace_event_init
      tp_event->perf_events = list;(1)
      tp_event->class->reg (2)← KPROBE ACTIVE
                                          Debug exception triggers
                                          ...
                                          kprobe_dispatcher
                                            kprobe_perf_func (tk->tp.flags & TP_FLAG_PROFILE)
                                              head = this_cpu_ptr(call->perf_events)(3)
                                              (perf_events is still NULL)

Problem:
1. CPU0 executes (1) assigning tp_event->perf_events = list
2. CPU0 executes (2) enabling kprobe functionality via class->reg()
3. CPU1 triggers and reaches kprobe_dispatcher
4. CPU1 checks TP_FLAG_PROFILE - condition passes (step 2 completed)
5. CPU1 calls kprobe_perf_func() and crashes at (3) because call->perf_events is still NULL

CPU1 sees that kprobe functionality is enabled but does not see that perf_events has been assigned.

Add pairing read and write memory barriers to guarantee that if CPU1 sees that kprobe functionality is enabled, it must also see that perf_events has been assigned.

Fixes 50d780560785 ("tracing/kprobes: Add probe handler dispatcher to support perf and ftrace concurrent use")
[ Dropped ftrace changes + context ]
---
 kernel/trace/trace_kprobe.c |   11 +++++++----
 kernel/trace/trace_probe.h  |    9 +++++++--
 kernel/trace/trace_uprobe.c |   12 ++++++++----
 3 files changed, 22 insertions(+), 10 deletions(-)
kernel/trace/trace_kprobe.c +7 -4
@@ -1782,14 +1782,15 @@ static int kprobe_register(struct trace_
 static int kprobe_dispatcher(struct kprobe *kp, struct pt_regs *regs)
 {
 	struct trace_kprobe *tk = container_of(kp, struct trace_kprobe, rp.kp);
+	unsigned int flags = trace_probe_load_flag(&tk->tp);
 	int ret = 0;
 
 	raw_cpu_inc(*tk->nhit);
 
-	if (trace_probe_test_flag(&tk->tp, TP_FLAG_TRACE))
+	if (flags & TP_FLAG_TRACE)
 		kprobe_trace_func(tk, regs);
 #ifdef CONFIG_PERF_EVENTS
-	if (trace_probe_test_flag(&tk->tp, TP_FLAG_PROFILE))
+	if (flags & TP_FLAG_PROFILE)
 		ret = kprobe_perf_func(tk, regs);
 #endif
 	return ret;
@@ -1800,13 +1801,15 @@ static int
 kretprobe_dispatcher(struct kretprobe_instance *ri, struct pt_regs *regs)
 {
 	struct trace_kprobe *tk = container_of(ri->rp, struct trace_kprobe, rp);
+	unsigned int flags;
 
 	raw_cpu_inc(*tk->nhit);
 
-	if (trace_probe_test_flag(&tk->tp, TP_FLAG_TRACE))
+	flags = trace_probe_load_flag(&tk->tp);
+	if (flags & TP_FLAG_TRACE)
 		kretprobe_trace_func(tk, ri, regs);
 #ifdef CONFIG_PERF_EVENTS
-	if (trace_probe_test_flag(&tk->tp, TP_FLAG_PROFILE))
+	if (flags & TP_FLAG_PROFILE)
 		kretprobe_perf_func(tk, ri, regs);
 #endif
 	return 0;	/* We don't tweek kernel, so just return 0 */
kernel/trace/trace_probe.h +7 -2
@@ -251,16 +251,21 @@ struct event_file_link {
 	struct list_head		list;
 };
 
+static inline unsigned int trace_probe_load_flag(struct trace_probe *tp)
+{
+	return smp_load_acquire(&tp->event->flags);
+}
+
 static inline bool trace_probe_test_flag(struct trace_probe *tp,
 					 unsigned int flag)
 {
-	return !!(tp->event->flags & flag);
+	return !!(trace_probe_load_flag(tp) & flag);
 }
 
 static inline void trace_probe_set_flag(struct trace_probe *tp,
 					unsigned int flag)
 {
-	tp->event->flags |= flag;
+	smp_store_release(&tp->event->flags, tp->event->flags | flag);
 }
 
 static inline void trace_probe_clear_flag(struct trace_probe *tp,
kernel/trace/trace_uprobe.c +8 -4
@@ -1484,6 +1484,7 @@ static int uprobe_dispatcher(struct upro
 	struct uprobe_dispatch_data udd;
 	struct uprobe_cpu_buffer *ucb;
 	int dsize, esize;
+	unsigned int flags;
 	int ret = 0;
 
 
@@ -1504,11 +1505,12 @@ static int uprobe_dispatcher(struct upro
 	ucb = uprobe_buffer_get();
 	store_trace_args(ucb->buf, &tu->tp, regs, esize, dsize);
 
-	if (trace_probe_test_flag(&tu->tp, TP_FLAG_TRACE))
+	flags = trace_probe_load_flag(&tu->tp);
+	if (flags & TP_FLAG_TRACE)
 		ret |= uprobe_trace_func(tu, regs, ucb, dsize);
 
 #ifdef CONFIG_PERF_EVENTS
-	if (trace_probe_test_flag(&tu->tp, TP_FLAG_PROFILE))
+	if (flags & TP_FLAG_PROFILE)
 		ret |= uprobe_perf_func(tu, regs, ucb, dsize);
 #endif
 	uprobe_buffer_put(ucb);
@@ -1522,6 +1524,7 @@ static int uretprobe_dispatcher(struct u
 	struct uprobe_dispatch_data udd;
 	struct uprobe_cpu_buffer *ucb;
 	int dsize, esize;
+	unsigned int flags;
 
 	tu = container_of(con, struct trace_uprobe, consumer);
 
@@ -1539,11 +1542,12 @@ static int uretprobe_dispatcher(struct u
 	ucb = uprobe_buffer_get();
 	store_trace_args(ucb->buf, &tu->tp, regs, esize, dsize);
 
-	if (trace_probe_test_flag(&tu->tp, TP_FLAG_TRACE))
+	flags = trace_probe_load_flag(&tu->tp);
+	if (flags & TP_FLAG_TRACE)
 		uretprobe_trace_func(tu, func, regs, ucb, dsize);
 
 #ifdef CONFIG_PERF_EVENTS
-	if (trace_probe_test_flag(&tu->tp, TP_FLAG_PROFILE))
+	if (flags & TP_FLAG_PROFILE)
 		uretprobe_perf_func(tu, func, regs, ucb, dsize);
 #endif
 	uprobe_buffer_put(ucb);
author maintainer
#179 lore raw

PATCH 174/332 dm: fix NULL pointer dereference in __dm_suspend()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Zheng Qixing <[email protected]>

[ Upstream commit 8d33a030c566e1f105cd5bf27f37940b6367f3be ]

There is a race condition between dm device suspend and table load that can lead to null pointer dereference. The issue occurs when suspend is invoked before table load completes:

BUG: kernel NULL pointer dereference, address: 0000000000000054
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 6 PID: 6798 Comm: dmsetup Not tainted 6.6.0-g7e52f5f0ca9b #62
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014
RIP: 0010:blk_mq_wait_quiesce_done+0x0/0x50
Call Trace:
  <TASK>
  blk_mq_quiesce_queue+0x2c/0x50
  dm_stop_queue+0xd/0x20
  __dm_suspend+0x130/0x330
  dm_suspend+0x11a/0x180
  dev_suspend+0x27e/0x560
  ctl_ioctl+0x4cf/0x850
  dm_ctl_ioctl+0xd/0x20
  vfs_ioctl+0x1d/0x50
  __se_sys_ioctl+0x9b/0xc0
  __x64_sys_ioctl+0x19/0x30
  x64_sys_call+0x2c4a/0x4620
  do_syscall_64+0x9e/0x1b0

The issue can be triggered as below:

T1 T2
dm_suspend table_load
__dm_suspend dm_setup_md_queue

						dm_mq_init_request_queue
						blk_mq_init_allocated_queue
						=> q->mq_ops = set->ops; (1)
dm_stop_queue / dm_wait_for_completion
=> q->tag_set NULL pointer!	(2)
						=> q->tag_set = set; (3)

Fix this by checking if a valid table (map) exists before performing request-based suspend and waiting for target I/O. When map is NULL, skip these table-dependent suspend steps.

Even when map is NULL, no I/O can reach any target because there is no table loaded; I/O submitted in this state will fail early in the DM layer. Skipping the table-dependent suspend logic in this case is safe and avoids NULL pointer dereferences.

Fixes c4576aed8d85 ("dm: fix request-based dm's use of dm_wait_for_completion")
[ omitted DMF_QUEUE_STOPPED flag setting and braces absent in 5.15 ]
---
 drivers/md/dm.c |    7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/md/dm.c +4 -3
@@ -2457,7 +2457,7 @@ static int __dm_suspend(struct mapped_de
 {
 	bool do_lockfs = suspend_flags & DM_SUSPEND_LOCKFS_FLAG;
 	bool noflush = suspend_flags & DM_SUSPEND_NOFLUSH_FLAG;
-	int r;
+	int r = 0;
 
 	lockdep_assert_held(&md->suspend_lock);
 
@@ -2509,7 +2509,7 @@ static int __dm_suspend(struct mapped_de
 	 * Stop md->queue before flushing md->wq in case request-based
 	 * dm defers requests to md->wq from md->queue.
 	 */
-	if (dm_request_based(md))
+	if (map && dm_request_based(md))
 		dm_stop_queue(md->queue);
 
 	flush_workqueue(md->wq);
@@ -2519,7 +2519,8 @@ static int __dm_suspend(struct mapped_de
 	 * We call dm_wait_for_completion to wait for all existing requests
 	 * to finish.
 	 */
-	r = dm_wait_for_completion(md, task_state);
+	if (map)
+		r = dm_wait_for_completion(md, task_state);
 	if (!r)
 		set_bit(dmf_suspended_flag, &md->flags);
 
author maintainer
#180 lore raw

PATCH 175/332 mfd: intel_soc_pmic_chtdc_ti: Fix invalid regmap-config max_register value

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Hans de Goede <[email protected]>

[ Upstream commit 70e997e0107e5ed85c1a3ef2adfccbe351c29d71 ]

The max_register = 128 setting in the regmap config is not valid.

The Intel Dollar Cove TI PMIC has an eeprom unlock register at address 0x88 and a number of EEPROM registers at 0xF?. Increase max_register to 0xff so that these registers can be accessed.

Stable-dep-of: 64e0d839c589 ("mfd: intel_soc_pmic_chtdc_ti: Set use_single_read regmap_config flag")

---
 drivers/mfd/intel_soc_pmic_chtdc_ti.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mfd/intel_soc_pmic_chtdc_ti.c +1 -1
@@ -81,7 +81,7 @@ static struct mfd_cell chtdc_ti_dev[] =
 static const struct regmap_config chtdc_ti_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
-	.max_register = 128,
+	.max_register = 0xff,
 	.cache_type = REGCACHE_NONE,
 };
 
author maintainer
#181 lore raw

PATCH 176/332 mfd: intel_soc_pmic_chtdc_ti: Drop unneeded assignment for cache_type

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Andy Shevchenko <[email protected]>

[ Upstream commit 9eb99c08508714906db078b5efbe075329a3fb06 ]

REGCACHE_NONE is the default type of the cache when not provided. Drop unneeded explicit assignment to it.

Note, it's defined to 0, and if ever be redefined, it will break literally a lot of the drivers, so it very unlikely to happen.

Stable-dep-of: 64e0d839c589 ("mfd: intel_soc_pmic_chtdc_ti: Set use_single_read regmap_config flag")

---
 drivers/mfd/intel_soc_pmic_chtdc_ti.c |    1 -
 1 file changed, 1 deletion(-)
drivers/mfd/intel_soc_pmic_chtdc_ti.c +0 -1
@@ -82,7 +82,6 @@ static const struct regmap_config chtdc_
 	.reg_bits = 8,
 	.val_bits = 8,
 	.max_register = 0xff,
-	.cache_type = REGCACHE_NONE,
 };
 
 static const struct regmap_irq chtdc_ti_irqs[] = {
author maintainer
#182 lore raw

PATCH 177/332 mfd: intel_soc_pmic_chtdc_ti: Set use_single_read regmap_config flag

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Hans de Goede <[email protected]>

[ Upstream commit 64e0d839c589f4f2ecd2e3e5bdb5cee6ba6bade9 ]

Testing has shown that reading multiple registers at once (for 10-bit ADC values) does not work. Set the use_single_read regmap_config flag to make regmap split these for us.

This should fix temperature opregion accesses done by drivers/acpi/pmic/intel_pmic_chtdc_ti.c and is also necessary for the upcoming drivers for the ADC and battery MFD cells.

---
 drivers/mfd/intel_soc_pmic_chtdc_ti.c |    2 ++
 1 file changed, 2 insertions(+)
drivers/mfd/intel_soc_pmic_chtdc_ti.c +2 -0
@@ -82,6 +82,8 @@ static const struct regmap_config chtdc_
 	.reg_bits = 8,
 	.val_bits = 8,
 	.max_register = 0xff,
+	/* The hardware does not support reading multiple registers at once */
+	.use_single_read = true,
 };
 
 static const struct regmap_irq chtdc_ti_irqs[] = {
author maintainer
#183 lore raw

PATCH 178/332 media: mc: Clear minor number before put device

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Edward Adam Davis <[email protected]>

[ Upstream commit 8cfc8cec1b4da88a47c243a11f384baefd092a50 ]

The device minor should not be cleared after the device is released.

Fixes 9e14868dc952 ("media: mc: Clear minor number reservation at unregistration time")
Reported-by [email protected]
[ moved clear_bit from media_devnode_release callback to media_devnode_unregister before put_device ]
---
 drivers/media/mc/mc-devnode.c |    6 +-----
 1 file changed, 1 insertion(+), 5 deletions(-)
drivers/media/mc/mc-devnode.c +1 -5
@@ -50,11 +50,6 @@ static void media_devnode_release(struct
 {
 	struct media_devnode *devnode = to_media_devnode(cd);
 
-	mutex_lock(&media_devnode_lock);
-	/* Mark device node number as free */
-	clear_bit(devnode->minor, media_devnode_nums);
-	mutex_unlock(&media_devnode_lock);
-
 	/* Release media_devnode and perform other cleanups as needed. */
 	if (devnode->release)
 		devnode->release(devnode);
@@ -283,6 +278,7 @@ void media_devnode_unregister(struct med
 	/* Delete the cdev on this minor as well */
 	cdev_device_del(&devnode->cdev, &devnode->dev);
 	devnode->media_dev = NULL;
+	clear_bit(devnode->minor, media_devnode_nums);
 	mutex_unlock(&media_devnode_lock);
 
 	put_device(&devnode->dev);
author maintainer
#184 lore raw

PATCH 179/332 Squashfs: add additional inode sanity checking

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Phillip Lougher <[email protected]>

[ Upstream commit 9ee94bfbe930a1b39df53fa2d7b31141b780eb5a ]

Patch series "Squashfs: performance improvement and a sanity check".

This patchset adds an additional sanity check when reading regular file inodes, and adds support for SEEK_DATA/SEEK_HOLE lseek() whence values.

This patch (of 2):

Add an additional sanity check when reading regular file inodes.

A regular file if the file size is an exact multiple of the filesystem block size cannot have a fragment. This is because by definition a fragment block stores tailends which are not a whole block in size.

Stable-dep-of: 9f1c14c1de1b ("Squashfs: reject negative file sizes in squashfs_read_inode()")

---
 fs/squashfs/inode.c |   20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)
fs/squashfs/inode.c +18 -2
@@ -140,8 +140,17 @@ int squashfs_read_inode(struct inode *in
 		if (err < 0)
 			goto failed_read;
 
+		inode->i_size = le32_to_cpu(sqsh_ino->file_size);
 		frag = le32_to_cpu(sqsh_ino->fragment);
 		if (frag != SQUASHFS_INVALID_FRAG) {
+			/*
+			 * the file cannot have a fragment (tailend) and have a
+			 * file size a multiple of the block size
+			 */
+			if ((inode->i_size & (msblk->block_size - 1)) == 0) {
+				err = -EINVAL;
+				goto failed_read;
+			}
 			frag_offset = le32_to_cpu(sqsh_ino->offset);
 			frag_size = squashfs_frag_lookup(sb, frag, &frag_blk);
 			if (frag_size < 0) {
@@ -155,7 +164,6 @@ int squashfs_read_inode(struct inode *in
 		}
 
 		set_nlink(inode, 1);
-		inode->i_size = le32_to_cpu(sqsh_ino->file_size);
 		inode->i_fop = &generic_ro_fops;
 		inode->i_mode |= S_IFREG;
 		inode->i_blocks = ((inode->i_size - 1) >> 9) + 1;
@@ -184,8 +192,17 @@ int squashfs_read_inode(struct inode *in
 		if (err < 0)
 			goto failed_read;
 
+		inode->i_size = le64_to_cpu(sqsh_ino->file_size);
 		frag = le32_to_cpu(sqsh_ino->fragment);
 		if (frag != SQUASHFS_INVALID_FRAG) {
+			/*
+			 * the file cannot have a fragment (tailend) and have a
+			 * file size a multiple of the block size
+			 */
+			if ((inode->i_size & (msblk->block_size - 1)) == 0) {
+				err = -EINVAL;
+				goto failed_read;
+			}
 			frag_offset = le32_to_cpu(sqsh_ino->offset);
 			frag_size = squashfs_frag_lookup(sb, frag, &frag_blk);
 			if (frag_size < 0) {
@@ -200,7 +217,6 @@ int squashfs_read_inode(struct inode *in
 
 		xattr_id = le32_to_cpu(sqsh_ino->xattr);
 		set_nlink(inode, le32_to_cpu(sqsh_ino->nlink));
-		inode->i_size = le64_to_cpu(sqsh_ino->file_size);
 		inode->i_op = &squashfs_inode_ops;
 		inode->i_fop = &generic_ro_fops;
 		inode->i_mode |= S_IFREG;
author maintainer
#185 lore raw

PATCH 180/332 Squashfs: reject negative file sizes in squashfs_read_inode()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Phillip Lougher <[email protected]>

[ Upstream commit 9f1c14c1de1bdde395f6cc893efa4f80a2ae3b2b ]

Syskaller reports a "WARNING in ovl_copy_up_file" in overlayfs.

This warning is ultimately caused because the underlying Squashfs file system returns a file with a negative file size.

This commit checks for a negative file size and returns EINVAL.

---
 fs/squashfs/inode.c |    4 ++++
 1 file changed, 4 insertions(+)
fs/squashfs/inode.c +4 -0
@@ -193,6 +193,10 @@ int squashfs_read_inode(struct inode *in
 			goto failed_read;
 
 		inode->i_size = le64_to_cpu(sqsh_ino->file_size);
+		if (inode->i_size < 0) {
+			err = -EINVAL;
+			goto failed_read;
+		}
 		frag = le32_to_cpu(sqsh_ino->fragment);
 		if (frag != SQUASHFS_INVALID_FRAG) {
 			/*
author maintainer
#186 lore raw

PATCH 181/332 udf: fix uninit-value use in udf_get_fileshortad

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Gianfranco Trad <[email protected]>

[ Upstream commit 264db9d666ad9a35075cc9ed9ec09d021580fbb1 ]

Check for overflow when computing alen in udf_current_aext to mitigate later uninit-value use in udf_get_fileshortad KMSAN bug[1]. After applying the patch reproducer did not trigger any issue[2].

[1] https://syzkaller.appspot.com/bug?extid=8901c4560b7ab5c2f9df
[2] https://syzkaller.appspot.com/x/log.txt?x=10242227980000

Stable-dep-of: 3bd5e45c2ce3 ("fs: udf: fix OOB read in lengthAllocDescs handling")

---
 fs/udf/inode.c |    9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
fs/udf/inode.c +6 -3
@@ -2190,12 +2190,15 @@ int8_t udf_current_aext(struct inode *in
 		alen = udf_file_entry_alloc_offset(inode) +
 							iinfo->i_lenAlloc;
 	} else {
+		struct allocExtDesc *header =
+			(struct allocExtDesc *)epos->bh->b_data;
+
 		if (!epos->offset)
 			epos->offset = sizeof(struct allocExtDesc);
 		ptr = epos->bh->b_data + epos->offset;
-		alen = sizeof(struct allocExtDesc) +
-			le32_to_cpu(((struct allocExtDesc *)epos->bh->b_data)->
-							lengthAllocDescs);
+		if (check_add_overflow(sizeof(struct allocExtDesc),
+				le32_to_cpu(header->lengthAllocDescs), &alen))
+			return -1;
 	}
 
 	switch (iinfo->i_alloc_type) {
author maintainer
#187 lore raw

PATCH 182/332 fs: udf: fix OOB read in lengthAllocDescs handling

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Larshin Sergey <[email protected]>

[ Upstream commit 3bd5e45c2ce30e239d596becd5db720f7eb83c99 ]

When parsing Allocation Extent Descriptor, lengthAllocDescs comes from on-disk data and must be validated against the block size. Crafted or corrupted images may set lengthAllocDescs so that the total descriptor length (sizeof(allocExtDesc) + lengthAllocDescs) exceeds the buffer, leading udf_update_tag() to call crc_itu_t() on out-of-bounds memory and trigger a KASAN use-after-free read.

BUG: KASAN: use-after-free in crc_itu_t+0x1d5/0x2b0 lib/crc-itu-t.c:60
Read of size 1 at addr ffff888041e7d000 by task syz-executor317/5309

CPU: 0 UID: 0 PID: 5309 Comm: syz-executor317 Not tainted 6.12.0-rc4-syzkaller-00261-g850925a8133c #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:94 [inline]
 dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120
 print_address_description mm/kasan/report.c:377 [inline]
 print_report+0x169/0x550 mm/kasan/report.c:488
 kasan_report+0x143/0x180 mm/kasan/report.c:601
 crc_itu_t+0x1d5/0x2b0 lib/crc-itu-t.c:60
 udf_update_tag+0x70/0x6a0 fs/udf/misc.c:261
 udf_write_aext+0x4d8/0x7b0 fs/udf/inode.c:2179
 extent_trunc+0x2f7/0x4a0 fs/udf/truncate.c:46
 udf_truncate_tail_extent+0x527/0x7e0 fs/udf/truncate.c:106
 udf_release_file+0xc1/0x120 fs/udf/file.c:185
 __fput+0x23f/0x880 fs/file_table.c:431
 task_work_run+0x24f/0x310 kernel/task_work.c:239
 exit_task_work include/linux/task_work.h:43 [inline]
 do_exit+0xa2f/0x28e0 kernel/exit.c:939
 do_group_exit+0x207/0x2c0 kernel/exit.c:1088
 __do_sys_exit_group kernel/exit.c:1099 [inline]
 __se_sys_exit_group kernel/exit.c:1097 [inline]
 __x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1097
 x64_sys_call+0x2634/0x2640 arch/x86/include/generated/asm/syscalls_64.h:232
 do_syscall_x64 arch/x86/entry/common.c:52 [inline]
 do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
 entry_SYSCALL_64_after_hwframe+0x77/0x7f
 </TASK>

Validate the computed total length against epos->bh->b_size.

Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

---
 fs/udf/inode.c |    3 +++
 1 file changed, 3 insertions(+)
fs/udf/inode.c +3 -0
@@ -2199,6 +2199,9 @@ int8_t udf_current_aext(struct inode *in
 		if (check_add_overflow(sizeof(struct allocExtDesc),
 				le32_to_cpu(header->lengthAllocDescs), &alen))
 			return -1;
+
+		if (alen > epos->bh->b_size)
+			return -1;
 	}
 
 	switch (iinfo->i_alloc_type) {
author maintainer
#188 lore raw

PATCH 183/332 ASoC: codecs: wcd934x: Simplify with dev_err_probe

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Krzysztof Kozlowski <[email protected]>

[ Upstream commit fa92f4294283cc7d1f29151420be9e9336182518 ]

Replace dev_err() in probe() path with dev_err_probe() to:
1. Make code a bit simpler and easier to read,
2. Do not print messages on deferred probe.

Stable-dep-of: 4e65bda8273c ("ASoC: wcd934x: fix error handling in wcd934x_codec_parse_data()")

---
 sound/soc/codecs/wcd934x.c |   19 +++++++------------
 1 file changed, 7 insertions(+), 12 deletions(-)
sound/soc/codecs/wcd934x.c +7 -12
@@ -5032,10 +5032,9 @@ static int wcd934x_codec_parse_data(stru
 	slim_get_logical_addr(wcd->sidev);
 	wcd->if_regmap = regmap_init_slimbus(wcd->sidev,
 				  &wcd934x_ifc_regmap_config);
-	if (IS_ERR(wcd->if_regmap)) {
-		dev_err(dev, "Failed to allocate ifc register map\n");
-		return PTR_ERR(wcd->if_regmap);
-	}
+	if (IS_ERR(wcd->if_regmap))
+		return dev_err_probe(dev, PTR_ERR(wcd->if_regmap),
+				     "Failed to allocate ifc register map\n");
 
 	of_property_read_u32(dev->parent->of_node, "qcom,dmic-sample-rate",
 			     &wcd->dmic_sample_rate);
@@ -5074,19 +5073,15 @@ static int wcd934x_codec_probe(struct pl
 	memcpy(wcd->tx_chs, wcd934x_tx_chs, sizeof(wcd934x_tx_chs));
 
 	irq = regmap_irq_get_virq(data->irq_data, WCD934X_IRQ_SLIMBUS);
-	if (irq < 0) {
-		dev_err(wcd->dev, "Failed to get SLIM IRQ\n");
-		return irq;
-	}
+	if (irq < 0)
+		return dev_err_probe(wcd->dev, irq, "Failed to get SLIM IRQ\n");
 
 	ret = devm_request_threaded_irq(dev, irq, NULL,
 					wcd934x_slim_irq_handler,
 					IRQF_TRIGGER_RISING,
 					"slim", wcd);
-	if (ret) {
-		dev_err(dev, "Failed to request slimbus irq\n");
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to request slimbus irq\n");
 
 	wcd934x_register_mclk_output(wcd);
 	platform_set_drvdata(pdev, wcd);
author maintainer
#189 lore raw

PATCH 184/332 ASoC: wcd934x: fix error handling in wcd934x_codec_parse_data()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Ma Ke <[email protected]>

[ Upstream commit 4e65bda8273c938039403144730923e77916a3d7 ]

wcd934x_codec_parse_data() contains a device reference count leak in of_slim_get_device() where device_find_child() increases the reference count of the device but this reference is not properly decreased in the success path. Add put_device() in wcd934x_codec_parse_data() and add devm_add_action_or_reset() in the probe function, which ensures that the reference count of the device is correctly managed.

Memory leak in regmap_init_slimbus() as the allocated regmap is not released when the device is removed. Using devm_regmap_init_slimbus() instead of regmap_init_slimbus() to ensure automatic regmap cleanup on device removal.

Calling path: of_slim_get_device() -> of_find_slim_device() -> device_find_child(). As comment of device_find_child() says, 'NOTE:
you will need to drop the reference with put_device() after use.'.

Found by code review.

---
 sound/soc/codecs/wcd934x.c |   17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)
sound/soc/codecs/wcd934x.c +15 -2
@@ -5011,6 +5011,13 @@ static const struct snd_soc_component_dr
 	.num_dapm_routes = ARRAY_SIZE(wcd934x_audio_map),
 };
 
+static void wcd934x_put_device_action(void *data)
+{
+	struct device *dev = data;
+
+	put_device(dev);
+}
+
 static int wcd934x_codec_parse_data(struct wcd934x_codec *wcd)
 {
 	struct device *dev = &wcd->sdev->dev;
@@ -5030,11 +5037,13 @@ static int wcd934x_codec_parse_data(stru
 	}
 
 	slim_get_logical_addr(wcd->sidev);
-	wcd->if_regmap = regmap_init_slimbus(wcd->sidev,
+	wcd->if_regmap = devm_regmap_init_slimbus(wcd->sidev,
 				  &wcd934x_ifc_regmap_config);
-	if (IS_ERR(wcd->if_regmap))
+	if (IS_ERR(wcd->if_regmap)) {
+		put_device(&wcd->sidev->dev);
 		return dev_err_probe(dev, PTR_ERR(wcd->if_regmap),
 				     "Failed to allocate ifc register map\n");
+	}
 
 	of_property_read_u32(dev->parent->of_node, "qcom,dmic-sample-rate",
 			     &wcd->dmic_sample_rate);
@@ -5065,6 +5074,10 @@ static int wcd934x_codec_probe(struct pl
 		return ret;
 	}
 
+	ret = devm_add_action_or_reset(dev, wcd934x_put_device_action, &wcd->sidev->dev);
+	if (ret)
+		return ret;
+
 	/* set default rate 9P6MHz */
 	regmap_update_bits(wcd->regmap, WCD934X_CODEC_RPM_CLK_MCLK_CFG,
 			   WCD934X_CODEC_RPM_CLK_MCLK_CFG_MCLK_MASK,
author maintainer
#190 lore raw

PATCH 185/332 KVM: x86: Dont (re)check L1 intercepts when completing userspace I/O

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Sean Christopherson <[email protected]>

[ Upstream commit e750f85391286a4c8100275516973324b621a269 ]

When completing emulation of instruction that generated a userspace exit for I/O, don't recheck L1 intercepts as KVM has already finished that phase of instruction execution, i.e. has already committed to allowing L2 to perform I/O. If L1 (or host userspace) modifies the I/O permission bitmaps during the exit to userspace, KVM will treat the access as being intercepted despite already having emulated the I/O access.

Pivot on EMULTYPE_NO_DECODE to detect that KVM is completing emulation. Of the three users of EMULTYPE_NO_DECODE, only complete_emulated_io() (the intended "recipient") can reach the code in question. gp_interception()'s use is mutually exclusive with is_guest_mode(), and complete_emulated_insn_gp() unconditionally pairs EMULTYPE_NO_DECODE with EMULTYPE_SKIP.

The bad behavior was detected by a syzkaller program that toggles port I/O interception during the userspace I/O exit, ultimately resulting in a WARN on vcpu->arch.pio.count being non-zero due to KVM no completing emulation of the I/O instruction.

  WARNING: CPU: 23 PID: 1083 at arch/x86/kvm/x86.c:8039 emulator_pio_in_out+0x154/0x170 [kvm]
  Modules linked in: kvm_intel kvm irqbypass
  CPU: 23 UID: 1000 PID: 1083 Comm: repro Not tainted 6.16.0-rc5-c1610d2d66b1-next-vm #74 NONE
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
  RIP: 0010:emulator_pio_in_out+0x154/0x170 [kvm]
  PKRU: 55555554
  Call Trace:
   <TASK>
   kvm_fast_pio+0xd6/0x1d0 [kvm]
   vmx_handle_exit+0x149/0x610 [kvm_intel]
   kvm_arch_vcpu_ioctl_run+0xda8/0x1ac0 [kvm]
   kvm_vcpu_ioctl+0x244/0x8c0 [kvm]
   __x64_sys_ioctl+0x8a/0xd0
   do_syscall_64+0x5d/0xc60
   entry_SYSCALL_64_after_hwframe+0x4b/0x53
   </TASK>
Reported-by [email protected]
Fixes 8a76d7f25f8f ("KVM: x86: Add x86 callback for intercept check")
Cc Jim Mattson <[email protected]>
[ is_guest_mode() was open coded ]
---
 arch/x86/kvm/emulate.c     |   11 ++++-------
 arch/x86/kvm/kvm_emulate.h |    2 +-
 arch/x86/kvm/x86.c         |    9 ++++++++-
 3 files changed, 13 insertions(+), 9 deletions(-)
arch/x86/kvm/emulate.c +4 -7
@@ -5544,12 +5544,11 @@ void init_decode_cache(struct x86_emulat
 	ctxt->mem_read.end = 0;
 }
 
-int x86_emulate_insn(struct x86_emulate_ctxt *ctxt)
+int x86_emulate_insn(struct x86_emulate_ctxt *ctxt, bool check_intercepts)
 {
 	const struct x86_emulate_ops *ops = ctxt->ops;
 	int rc = X86EMUL_CONTINUE;
 	int saved_dst_type = ctxt->dst.type;
-	unsigned emul_flags;
 
 	ctxt->mem_read.pos = 0;
 
@@ -5563,8 +5562,6 @@ int x86_emulate_insn(struct x86_emulate_
 		rc = emulate_ud(ctxt);
 		goto done;
 	}
-
-	emul_flags = ctxt->ops->get_hflags(ctxt);
 	if (unlikely(ctxt->d &
 		     (No64|Undefined|Sse|Mmx|Intercept|CheckPerm|Priv|Prot|String))) {
 		if ((ctxt->mode == X86EMUL_MODE_PROT64 && (ctxt->d & No64)) ||
@@ -5598,7 +5595,7 @@ int x86_emulate_insn(struct x86_emulate_
 				fetch_possible_mmx_operand(&ctxt->dst);
 		}
 
-		if (unlikely(emul_flags & X86EMUL_GUEST_MASK) && ctxt->intercept) {
+		if (unlikely(check_intercepts) && ctxt->intercept) {
 			rc = emulator_check_intercept(ctxt, ctxt->intercept,
 						      X86_ICPT_PRE_EXCEPT);
 			if (rc != X86EMUL_CONTINUE)
@@ -5627,7 +5624,7 @@ int x86_emulate_insn(struct x86_emulate_
 				goto done;
 		}
 
-		if (unlikely(emul_flags & X86EMUL_GUEST_MASK) && (ctxt->d & Intercept)) {
+		if (unlikely(check_intercepts) && (ctxt->d & Intercept)) {
 			rc = emulator_check_intercept(ctxt, ctxt->intercept,
 						      X86_ICPT_POST_EXCEPT);
 			if (rc != X86EMUL_CONTINUE)
@@ -5681,7 +5678,7 @@ int x86_emulate_insn(struct x86_emulate_
 
 special_insn:
 
-	if (unlikely(emul_flags & X86EMUL_GUEST_MASK) && (ctxt->d & Intercept)) {
+	if (unlikely(check_intercepts) && (ctxt->d & Intercept)) {
 		rc = emulator_check_intercept(ctxt, ctxt->intercept,
 					      X86_ICPT_POST_MEMACCESS);
 		if (rc != X86EMUL_CONTINUE)
arch/x86/kvm/kvm_emulate.h +1 -1
@@ -499,7 +499,7 @@ bool x86_page_table_writing_insn(struct
 #define EMULATION_RESTART 1
 #define EMULATION_INTERCEPTED 2
 void init_decode_cache(struct x86_emulate_ctxt *ctxt);
-int x86_emulate_insn(struct x86_emulate_ctxt *ctxt);
+int x86_emulate_insn(struct x86_emulate_ctxt *ctxt, bool check_intercepts);
 int emulator_task_switch(struct x86_emulate_ctxt *ctxt,
 			 u16 tss_selector, int idt_index, int reason,
 			 bool has_error_code, u32 error_code);
arch/x86/kvm/x86.c +8 -1
@@ -7668,7 +7668,14 @@ restart:
 		ctxt->exception.address = 0;
 	}
 
-	r = x86_emulate_insn(ctxt);
+	/*
+	 * Check L1's instruction intercepts when emulating instructions for
+	 * L2, unless KVM is re-emulating a previously decoded instruction,
+	 * e.g. to complete userspace I/O, in which case KVM has already
+	 * checked the intercepts.
+	 */
+	r = x86_emulate_insn(ctxt, is_guest_mode(vcpu) &&
+				   !(emulation_type & EMULTYPE_NO_DECODE));
 
 	if (r == EMULATION_INTERCEPTED)
 		return 1;
author maintainer
#191 lore raw

PATCH 186/332 net/9p: fix double req put in p9_fd_cancelled

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nalivayko Sergey <[email protected]>

[ Upstream commit 674b56aa57f9379854cb6798c3bbcef7e7b51ab7 ]

Syzkaller reports a KASAN issue as below:

general protection fault, probably for non-canonical address 0xfbd59c0000000021: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: maybe wild-memory-access in range [0xdead000000000108-0xdead00000000010f]
CPU: 0 PID: 5083 Comm: syz-executor.2 Not tainted 6.1.134-syzkaller-00037-g855bd1d7d838 #0
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
RIP: 0010:__list_del include/linux/list.h:114 [inline]
RIP: 0010:__list_del_entry include/linux/list.h:137 [inline]
RIP: 0010:list_del include/linux/list.h:148 [inline]
RIP: 0010:p9_fd_cancelled+0xe9/0x200 net/9p/trans_fd.c:734

Call Trace:
 <TASK>
 p9_client_flush+0x351/0x440 net/9p/client.c:614
 p9_client_rpc+0xb6b/0xc70 net/9p/client.c:734
 p9_client_version net/9p/client.c:920 [inline]
 p9_client_create+0xb51/0x1240 net/9p/client.c:1027
 v9fs_session_init+0x1f0/0x18f0 fs/9p/v9fs.c:408
 v9fs_mount+0xba/0xcb0 fs/9p/vfs_super.c:126
 legacy_get_tree+0x108/0x220 fs/fs_context.c:632
 vfs_get_tree+0x8e/0x300 fs/super.c:1573
 do_new_mount fs/namespace.c:3056 [inline]
 path_mount+0x6a6/0x1e90 fs/namespace.c:3386
 do_mount fs/namespace.c:3399 [inline]
 __do_sys_mount fs/namespace.c:3607 [inline]
 __se_sys_mount fs/namespace.c:3584 [inline]
 __x64_sys_mount+0x283/0x300 fs/namespace.c:3584
 do_syscall_x64 arch/x86/entry/common.c:51 [inline]
 do_syscall_64+0x35/0x80 arch/x86/entry/common.c:81
 entry_SYSCALL_64_after_hwframe+0x6e/0xd8

This happens because of a race condition between:

- The 9p client sending an invalid flush request and later cleaning it up;
- The 9p client in p9_read_work() canceled all pending requests.

      Thread 1                              Thread 2
    ...
    p9_client_create()
    ...
    p9_fd_create()
    ...
    p9_conn_create()
    ...
    // start Thread 2
    INIT_WORK(&m->rq, p9_read_work);
                                        p9_read_work()
    ...
    p9_client_rpc()
    ...
                                        ...
                                        p9_conn_cancel()
                                        ...
                                        spin_lock(&m->req_lock);
    ...
    p9_fd_cancelled()
    ...
                                        ...
                                        spin_unlock(&m->req_lock);
                                        // status rewrite
                                        p9_client_cb(m->client, req, REQ_STATUS_ERROR)
                                        // first remove
                                        list_del(&req->req_list);
                                        ...

    spin_lock(&m->req_lock)
    ...
    // second remove
    list_del(&req->req_list);
    spin_unlock(&m->req_lock)

...

Commit 74d6a5d56629 ("9p/trans_fd: Fix concurrency del of req_list in p9_fd_cancelled/p9_read_work") fixes a concurrency issue in the 9p filesystem client where the req_list could be deleted simultaneously by both p9_read_work and p9_fd_cancelled functions, but for the case where req->status equals REQ_STATUS_RCVD.

Update the check for req->status in p9_fd_cancelled to skip processing not just received requests, but anything that is not SENT, as whatever changed the state from SENT also removed the request from its list.

Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

Fixes afd8d6541155 ("9P: Add cancelled() to the transport functions.")

Message-ID: <[email protected]>

[updated the check from status == RECV || status == ERROR to status != SENT]
[ replaced m->req_lock with client->lock ]
---
 net/9p/trans_fd.c |    8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
net/9p/trans_fd.c +4 -4
@@ -711,10 +711,10 @@ static int p9_fd_cancelled(struct p9_cli
 	p9_debug(P9_DEBUG_TRANS, "client %p req %p\n", client, req);
 
 	spin_lock(&client->lock);
-	/* Ignore cancelled request if message has been received
-	 * before lock.
-	 */
-	if (req->status == REQ_STATUS_RCVD) {
+	/* Ignore cancelled request if status changed since the request was
+	 * processed in p9_client_flush()
+	*/
+	if (req->status != REQ_STATUS_SENT) {
 		spin_unlock(&client->lock);
 		return 0;
 	}
author maintainer
#192 lore raw

PATCH 187/332 minixfs: Verify inode mode when loading from disk

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Tetsuo Handa <[email protected]>

[ Upstream commit 73861970938ad1323eb02bbbc87f6fbd1e5bacca ]

The inode mode loaded from corrupted disk can be invalid. Do like what commit 0a9e74051313 ("isofs: Verify inode mode when loading from disk") does.

---
 fs/minix/inode.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
fs/minix/inode.c +7 -1
index e938f5b1e4b94..7636e789eb49b 100644
@@ -469,8 +469,14 @@ void minix_set_inode(struct inode *inode, dev_t rdev)
 		inode->i_op = &minix_symlink_inode_operations;
 		inode_nohighmem(inode);
 		inode->i_mapping->a_ops = &minix_aops;
-	} else
+	} else if (S_ISCHR(inode->i_mode) || S_ISBLK(inode->i_mode) ||
+		   S_ISFIFO(inode->i_mode) || S_ISSOCK(inode->i_mode)) {
 		init_special_inode(inode, inode->i_mode, rdev);
+	} else {
+		printk(KERN_DEBUG "MINIX-fs: Invalid file type 0%04o for inode %lu.\n",
+		       inode->i_mode, inode->i_ino);
+		make_bad_inode(inode);
+	}
 }
 
 /*
Signature · 1 line
2.51.0
author maintainer
#193 lore raw

PATCH 188/332 pid: Add a judgment for ns null in pid_nr_ns

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: gaoxiang17 <[email protected]>

[ Upstream commit 006568ab4c5ca2309ceb36fa553e390b4aa9c0c7 ]

__task_pid_nr_ns

        ns = task_active_pid_ns(current);
        pid_nr_ns(rcu_dereference(*task_pid_ptr(task, type)), ns);
                if (pid && ns->level <= pid->level) {

Sometimes null is returned for task_active_pid_ns. Then it will trigger kernel panic in pid_nr_ns.

For example:

	Unable to handle kernel NULL pointer dereference at virtual address 0000000000000058
	Mem abort info:
	ESR = 0x0000000096000007
	EC = 0x25: DABT (current EL), IL = 32 bits
	SET = 0, FnV = 0
	EA = 0, S1PTW = 0
	FSC = 0x07: level 3 translation fault
	Data abort info:
	ISV = 0, ISS = 0x00000007, ISS2 = 0x00000000
	CM = 0, WnR = 0, TnD = 0, TagAccess = 0
	GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
	user pgtable: 4k pages, 39-bit VAs, pgdp=00000002175aa000
	[0000000000000058] pgd=08000002175ab003, p4d=08000002175ab003, pud=08000002175ab003, pmd=08000002175be003, pte=0000000000000000
	pstate: 834000c5 (Nzcv daIF +PAN -UAO +TCO +DIT -SSBS BTYPE=--)
	pc : __task_pid_nr_ns+0x74/0xd0
	lr : __task_pid_nr_ns+0x24/0xd0
	sp : ffffffc08001bd10
	x29: ffffffc08001bd10 x28: ffffffd4422b2000 x27: 0000000000000001
	x26: ffffffd442821168 x25: ffffffd442821000 x24: 00000f89492eab31
	x23: 00000000000000c0 x22: ffffff806f5693c0 x21: ffffff806f5693c0
	x20: 0000000000000001 x19: 0000000000000000 x18: 0000000000000000
	x17: 00000000529c6ef0 x16: 00000000529c6ef0 x15: 00000000023a1adc
	x14: 0000000000000003 x13: 00000000007ef6d8 x12: 001167c391c78800
	x11: 00ffffffffffffff x10: 0000000000000000 x9 : 0000000000000001
	x8 : ffffff80816fa3c0 x7 : 0000000000000000 x6 : 49534d702d535449
	x5 : ffffffc080c4c2c0 x4 : ffffffd43ee128c8 x3 : ffffffd43ee124dc
	x2 : 0000000000000000 x1 : 0000000000000001 x0 : ffffff806f5693c0
	Call trace:
	__task_pid_nr_ns+0x74/0xd0
	...
	__handle_irq_event_percpu+0xd4/0x284
	handle_irq_event+0x48/0xb0
	handle_fasteoi_irq+0x160/0x2d8
	generic_handle_domain_irq+0x44/0x60
	gic_handle_irq+0x4c/0x114
	call_on_irq_stack+0x3c/0x74
	do_interrupt_handler+0x4c/0x84
	el1_interrupt+0x34/0x58
	el1h_64_irq_handler+0x18/0x24
	el1h_64_irq+0x68/0x6c
	account_kernel_stack+0x60/0x144
	exit_task_stack_account+0x1c/0x80
	do_exit+0x7e4/0xaf8
	...
	get_signal+0x7bc/0x8d8
	do_notify_resume+0x128/0x828
	el0_svc+0x6c/0x70
	el0t_64_sync_handler+0x68/0xbc
	el0t_64_sync+0x1a8/0x1ac
	Code: 35fffe54 911a02a8 f9400108 b4000128 (b9405a69)
	---[ end trace 0000000000000000 ]---
	Kernel panic - not syncing: Oops: Fatal exception in interrupt
---
 kernel/pid.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/pid.c +1 -1
index 0820f2c50bb0c..a5a08476f3756 100644
@@ -474,7 +474,7 @@ pid_t pid_nr_ns(struct pid *pid, struct pid_namespace *ns)
 	struct upid *upid;
 	pid_t nr = 0;
 
-	if (pid && ns->level <= pid->level) {
+	if (pid && ns && ns->level <= pid->level) {
 		upid = &pid->numbers[ns->level];
 		if (upid->ns == ns)
 			nr = upid->nr;
Signature · 1 line
2.51.0
author maintainer
#194 lore raw

PATCH 189/332 fs: Add initramfs_options to set initramfs mount options

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Lichen Liu <[email protected]>

[ Upstream commit 278033a225e13ec21900f0a92b8351658f5377f2 ]

When CONFIG_TMPFS is enabled, the initial root filesystem is a tmpfs. By default, a tmpfs mount is limited to using 50% of the available RAM for its content. This can be problematic in memory-constrained environments, particularly during a kdump capture.

In a kdump scenario, the capture kernel boots with a limited amount of memory specified by the 'crashkernel' parameter. If the initramfs is large, it may fail to unpack into the tmpfs rootfs due to insufficient space. This is because to get X MB of usable space in tmpfs, 2*X MB of memory must be available for the mount. This leads to an OOM failure during the early boot process, preventing a successful crash dump.

This patch introduces a new kernel command-line parameter, initramfs_options, which allows passing specific mount options directly to the rootfs when it is first mounted. This gives users control over the rootfs behavior.

For example, a user can now specify initramfs_options=size=75% to allow the tmpfs to use up to 75% of the available memory. This can significantly reduce the memory pressure for kdump.

Consider a practical example:

To unpack a 48MB initramfs, the tmpfs needs 48MB of usable space. With the default 50% limit, this requires a memory pool of 96MB to be available for the tmpfs mount. The total memory requirement is therefore
approximately: 16MB (vmlinuz) + 48MB (loaded initramfs) + 48MB (unpacked kernel) + 96MB (for tmpfs) + 12MB (runtime overhead) ≈ 220MB.

By using initramfs_options=size=75%, the memory pool required for the 48MB tmpfs is reduced to 48MB / 0.75 = 64MB. This reduces the total memory requirement by 32MB (96MB - 64MB), allowing the kdump to succeed with a smaller crashkernel size, such as 192MB.

An alternative approach of reusing the existing rootflags parameter was considered. However, a new, dedicated initramfs_options parameter was chosen to avoid altering the current behavior of rootflags (which applies to the final root filesystem) and to prevent any potential regressions.

Also add documentation for the new kernel parameter "initramfs_options"

This approach is inspired by prior discussions and patches on the topic.
Ref: https://www.lightofdawn.org/blog/?viewDetailed=00128
Ref: https://landley.net/notes-2015.html#01-01-2015
Ref: https://lkml.org/lkml/2021/6/29/783
Ref: https://www.kernel.org/doc/html/latest/filesystems/ramfs-rootfs-initramfs.html#what-is-rootfs

---
 Documentation/admin-guide/kernel-parameters.txt |  3 +++
 fs/namespace.c                                  | 11 ++++++++++-
 2 files changed, 13 insertions(+), 1 deletion(-)
Documentation/admin-guide/kernel-parameters.txt +3 -0
index bac4b1493222a..0f1605d78e83d 100644
@@ -4846,6 +4846,9 @@
 
 	rootflags=	[KNL] Set root filesystem mount option string
 
+	initramfs_options= [KNL]
+                        Specify mount options for for the initramfs mount.
+
 	rootfstype=	[KNL] Set root filesystem type
 
 	rootwait	[KNL] Wait (indefinitely) for root device to show up.
fs/namespace.c +10 -1
index d1751f9b6f1ce..e9b8d516f1919 100644
@@ -62,6 +62,15 @@ static int __init set_mphash_entries(char *str)
 }
 __setup("mphash_entries=", set_mphash_entries);
 
+static char * __initdata initramfs_options;
+static int __init initramfs_options_setup(char *str)
+{
+	initramfs_options = str;
+	return 1;
+}
+
+__setup("initramfs_options=", initramfs_options_setup);
+
 static u64 event;
 static DEFINE_IDA(mnt_id_ida);
 static DEFINE_IDA(mnt_group_ida);
@@ -3913,7 +3922,7 @@ static void __init init_mount_tree(void)
 	struct mnt_namespace *ns;
 	struct path root;
 
-	mnt = vfs_kern_mount(&rootfs_fs_type, 0, "rootfs", NULL);
+	mnt = vfs_kern_mount(&rootfs_fs_type, 0, "rootfs", initramfs_options);
 	if (IS_ERR(mnt))
 		panic("Can't create rootfs");
 
Signature · 1 line
2.51.0
author maintainer
#195 lore raw

PATCH 190/332 cramfs: Verify inode mode when loading from disk

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Tetsuo Handa <[email protected]>

[ Upstream commit 7f9d34b0a7cb93d678ee7207f0634dbf79e47fe5 ]

The inode mode loaded from corrupted disk can be invalid. Do like what commit 0a9e74051313 ("isofs: Verify inode mode when loading from disk") does.

---
 fs/cramfs/inode.c | 11 ++++++++++-
 1 file changed, 10 insertions(+), 1 deletion(-)
fs/cramfs/inode.c +10 -1
index 4b90cfd1ec360..fda92e56ccd69 100644
@@ -117,9 +117,18 @@ static struct inode *get_cramfs_inode(struct super_block *sb,
 		inode_nohighmem(inode);
 		inode->i_data.a_ops = &cramfs_aops;
 		break;
-	default:
+	case S_IFCHR:
+	case S_IFBLK:
+	case S_IFIFO:
+	case S_IFSOCK:
 		init_special_inode(inode, cramfs_inode->mode,
 				old_decode_dev(cramfs_inode->size));
+		break;
+	default:
+		printk(KERN_DEBUG "CRAMFS: Invalid file type 0%04o for inode %lu.\n",
+		       inode->i_mode, inode->i_ino);
+		iget_failed(inode);
+		return ERR_PTR(-EIO);
 	}
 
 	inode->i_mode = cramfs_inode->mode;
Signature · 1 line
2.51.0
author maintainer
#196 lore raw

PATCH 191/332 locking: Introduce __cleanup() based infrastructure

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Peter Zijlstra <[email protected]>

[ Upstream commit 54da6a0924311c7cf5015533991e44fb8eb12773 ]

Use __attribute__((__cleanup__(func))) to build:

- simple auto-release pointers using __free()

- 'classes' with constructor and destructor semantics for scope-based resource management.

- lock guards based on the above classes.

---
 drivers/dma/ioat/dma.c              |   12 +-
 include/linux/cleanup.h             |  171 ++++++++++++++++++++++++++++++++++++
 include/linux/compiler-clang.h      |    9 +
 include/linux/compiler_attributes.h |    6 +
 include/linux/device.h              |    7 +
 include/linux/file.h                |    6 +
 include/linux/irqflags.h            |    7 +
 include/linux/mutex.h               |    4 
 include/linux/percpu.h              |    4 
 include/linux/preempt.h             |    5 +
 include/linux/rcupdate.h            |    3 
 include/linux/rwsem.h               |    9 +
 include/linux/sched/task.h          |    2 
 include/linux/slab.h                |    3 
 include/linux/spinlock.h            |   32 ++++++
 include/linux/srcu.h                |    5 +
 scripts/checkpatch.pl               |    2 
 17 files changed, 280 insertions(+), 7 deletions(-)
 create mode 100644 include/linux/cleanup.h
drivers/dma/ioat/dma.c +6 -6
@@ -584,11 +584,11 @@ desc_get_errstat(struct ioatdma_chan *io
 }
 
 /**
- * __cleanup - reclaim used descriptors
+ * __ioat_cleanup - reclaim used descriptors
  * @ioat_chan: channel (ring) to clean
  * @phys_complete: zeroed (or not) completion address (from status)
  */
-static void __cleanup(struct ioatdma_chan *ioat_chan, dma_addr_t phys_complete)
+static void __ioat_cleanup(struct ioatdma_chan *ioat_chan, dma_addr_t phys_complete)
 {
 	struct ioatdma_device *ioat_dma = ioat_chan->ioat_dma;
 	struct ioat_ring_ent *desc;
@@ -675,7 +675,7 @@ static void ioat_cleanup(struct ioatdma_
 	spin_lock_bh(&ioat_chan->cleanup_lock);
 
 	if (ioat_cleanup_preamble(ioat_chan, &phys_complete))
-		__cleanup(ioat_chan, phys_complete);
+		__ioat_cleanup(ioat_chan, phys_complete);
 
 	if (is_ioat_halted(*ioat_chan->completion)) {
 		u32 chanerr = readl(ioat_chan->reg_base + IOAT_CHANERR_OFFSET);
@@ -712,7 +712,7 @@ static void ioat_restart_channel(struct
 
 	ioat_quiesce(ioat_chan, 0);
 	if (ioat_cleanup_preamble(ioat_chan, &phys_complete))
-		__cleanup(ioat_chan, phys_complete);
+		__ioat_cleanup(ioat_chan, phys_complete);
 
 	__ioat_restart_chan(ioat_chan);
 }
@@ -786,7 +786,7 @@ static void ioat_eh(struct ioatdma_chan
 
 	/* cleanup so tail points to descriptor that caused the error */
 	if (ioat_cleanup_preamble(ioat_chan, &phys_complete))
-		__cleanup(ioat_chan, phys_complete);
+		__ioat_cleanup(ioat_chan, phys_complete);
 
 	chanerr = readl(ioat_chan->reg_base + IOAT_CHANERR_OFFSET);
 	pci_read_config_dword(pdev, IOAT_PCI_CHANERR_INT_OFFSET, &chanerr_int);
@@ -943,7 +943,7 @@ void ioat_timer_event(struct timer_list
 		/* timer restarted in ioat_cleanup_preamble
 		 * and IOAT_COMPLETION_ACK cleared
 		 */
-		__cleanup(ioat_chan, phys_complete);
+		__ioat_cleanup(ioat_chan, phys_complete);
 		goto unlock_out;
 	}
 
include/linux/cleanup.h new file +171 -0

171 lines not on this page · raw message

include/linux/compiler-clang.h +9 -0
@@ -15,6 +15,15 @@
 
 /* Compiler specific definitions for Clang compiler */
 
+/*
+ * Clang prior to 17 is being silly and considers many __cleanup() variables
+ * as unused (because they are, their sole purpose is to go out of scope).
+ *
+ * https://reviews.llvm.org/D152180
+ */
+#undef __cleanup
+#define __cleanup(func) __maybe_unused __attribute__((__cleanup__(func)))
+
 /* same as gcc, this was present in clang-2.6 so we can assume it works
  * with any version that can compile the kernel
  */
include/linux/compiler_attributes.h +6 -0
@@ -95,6 +95,12 @@
 #define __cold                          __attribute__((__cold__))
 
 /*
+ *   gcc: https://gcc.gnu.org/onlinedocs/gcc/Common-Variable-Attributes.html#index-cleanup-variable-attribute
+ * clang: https://clang.llvm.org/docs/AttributeReference.html#cleanup
+ */
+#define __cleanup(func)			__attribute__((__cleanup__(func)))
+
+/*
  * Note the long name.
  *
  *   gcc: https://gcc.gnu.org/onlinedocs/gcc/Common-Function-Attributes.html#index-const-function-attribute
include/linux/device.h +7 -0
@@ -30,6 +30,7 @@
 #include <linux/device/bus.h>
 #include <linux/device/class.h>
 #include <linux/device/driver.h>
+#include <linux/cleanup.h>
 #include <asm/device.h>
 
 struct device;
@@ -829,6 +830,9 @@ void device_unregister(struct device *de
 void device_initialize(struct device *dev);
 int __must_check device_add(struct device *dev);
 void device_del(struct device *dev);
+
+DEFINE_FREE(device_del, struct device *, if (_T) device_del(_T))
+
 int device_for_each_child(struct device *dev, void *data,
 			  int (*fn)(struct device *dev, void *data));
 int device_for_each_child_reverse(struct device *dev, void *data,
@@ -957,6 +961,9 @@ extern int (*platform_notify_remove)(str
  */
 struct device *get_device(struct device *dev);
 void put_device(struct device *dev);
+
+DEFINE_FREE(put_device, struct device *, if (_T) put_device(_T))
+
 bool kill_device(struct device *dev);
 
 #ifdef CONFIG_DEVTMPFS
include/linux/file.h +6 -0
@@ -10,6 +10,7 @@
 #include <linux/types.h>
 #include <linux/posix_types.h>
 #include <linux/errno.h>
+#include <linux/cleanup.h>
 
 struct file;
 
@@ -82,6 +83,8 @@ static inline void fdput_pos(struct fd f
 	fdput(f);
 }
 
+DEFINE_CLASS(fd, struct fd, fdput(_T), fdget(fd), int fd)
+
 extern int f_dupfd(unsigned int from, struct file *file, unsigned flags);
 extern int replace_fd(unsigned fd, struct file *file, unsigned flags);
 extern void set_close_on_exec(unsigned int fd, int flag);
@@ -90,6 +93,9 @@ extern int __get_unused_fd_flags(unsigne
 extern int get_unused_fd_flags(unsigned flags);
 extern void put_unused_fd(unsigned int fd);
 
+DEFINE_CLASS(get_unused_fd, int, if (_T >= 0) put_unused_fd(_T),
+	     get_unused_fd_flags(flags), unsigned flags)
+
 extern void fd_install(unsigned int fd, struct file *file);
 
 extern int __receive_fd(int fd, struct file *file, int __user *ufd,
include/linux/irqflags.h +7 -0
@@ -13,6 +13,7 @@
 #define _LINUX_TRACE_IRQFLAGS_H
 
 #include <linux/typecheck.h>
+#include <linux/cleanup.h>
 #include <asm/irqflags.h>
 #include <asm/percpu.h>
 
@@ -248,4 +249,10 @@ do {						\
 
 #define irqs_disabled_flags(flags) raw_irqs_disabled_flags(flags)
 
+DEFINE_LOCK_GUARD_0(irq, local_irq_disable(), local_irq_enable())
+DEFINE_LOCK_GUARD_0(irqsave,
+		    local_irq_save(_T->flags),
+		    local_irq_restore(_T->flags),
+		    unsigned long flags)
+
 #endif
include/linux/mutex.h +4 -0
@@ -19,6 +19,7 @@
 #include <asm/processor.h>
 #include <linux/osq_lock.h>
 #include <linux/debug_locks.h>
+#include <linux/cleanup.h>
 
 struct ww_acquire_ctx;
 
@@ -224,4 +225,7 @@ enum mutex_trylock_recursive_enum {
 extern /* __deprecated */ __must_check enum mutex_trylock_recursive_enum
 mutex_trylock_recursive(struct mutex *lock);
 
+DEFINE_GUARD(mutex, struct mutex *, mutex_lock(_T), mutex_unlock(_T))
+DEFINE_FREE(mutex, struct mutex *, if (_T) mutex_unlock(_T))
+
 #endif /* __LINUX_MUTEX_H */
include/linux/percpu.h +4 -0
@@ -9,6 +9,7 @@
 #include <linux/printk.h>
 #include <linux/pfn.h>
 #include <linux/init.h>
+#include <linux/cleanup.h>
 
 #include <asm/percpu.h>
 
@@ -134,6 +135,9 @@ extern void __init setup_per_cpu_areas(v
 extern void __percpu *__alloc_percpu_gfp(size_t size, size_t align, gfp_t gfp);
 extern void __percpu *__alloc_percpu(size_t size, size_t align);
 extern void free_percpu(void __percpu *__pdata);
+
+DEFINE_FREE(free_percpu, void __percpu *, free_percpu(_T))
+
 extern phys_addr_t per_cpu_ptr_to_phys(void *addr);
 
 #define alloc_percpu_gfp(type, gfp)					\
include/linux/preempt.h +5 -0
@@ -8,6 +8,7 @@
  */
 
 #include <linux/linkage.h>
+#include <linux/cleanup.h>
 #include <linux/list.h>
 
 /*
@@ -352,4 +353,8 @@ static __always_inline void migrate_enab
 	preempt_enable();
 }
 
+DEFINE_LOCK_GUARD_0(preempt, preempt_disable(), preempt_enable())
+DEFINE_LOCK_GUARD_0(preempt_notrace, preempt_disable_notrace(), preempt_enable_notrace())
+DEFINE_LOCK_GUARD_0(migrate, migrate_disable(), migrate_enable())
+
 #endif /* __LINUX_PREEMPT_H */
include/linux/rcupdate.h +3 -0
@@ -27,6 +27,7 @@
 #include <linux/preempt.h>
 #include <linux/bottom_half.h>
 #include <linux/lockdep.h>
+#include <linux/cleanup.h>
 #include <asm/processor.h>
 #include <linux/cpumask.h>
 
@@ -1058,4 +1059,6 @@ rcu_head_after_call_rcu(struct rcu_head
 extern int rcu_expedited;
 extern int rcu_normal;
 
+DEFINE_LOCK_GUARD_0(rcu, rcu_read_lock(), rcu_read_unlock())
+
 #endif /* __LINUX_RCUPDATE_H */
include/linux/rwsem.h +9 -0
@@ -16,6 +16,8 @@
 #include <linux/spinlock.h>
 #include <linux/atomic.h>
 #include <linux/err.h>
+#include <linux/cleanup.h>
+
 #ifdef CONFIG_RWSEM_SPIN_ON_OWNER
 #include <linux/osq_lock.h>
 #endif
@@ -152,6 +154,13 @@ extern void up_read(struct rw_semaphore
  */
 extern void up_write(struct rw_semaphore *sem);
 
+DEFINE_GUARD(rwsem_read, struct rw_semaphore *, down_read(_T), up_read(_T))
+DEFINE_GUARD(rwsem_write, struct rw_semaphore *, down_write(_T), up_write(_T))
+
+DEFINE_FREE(up_read, struct rw_semaphore *, if (_T) up_read(_T))
+DEFINE_FREE(up_write, struct rw_semaphore *, if (_T) up_write(_T))
+
+
 /*
  * downgrade write lock to read lock
  */
include/linux/sched/task.h +2 -0
@@ -143,6 +143,8 @@ static inline void put_task_struct(struc
 		__put_task_struct(t);
 }
 
+DEFINE_FREE(put_task, struct task_struct *, if (_T) put_task_struct(_T))
+
 static inline void put_task_struct_many(struct task_struct *t, int nr)
 {
 	if (refcount_sub_and_test(nr, &t->usage))
include/linux/slab.h +3 -0
@@ -17,6 +17,7 @@
 #include <linux/types.h>
 #include <linux/workqueue.h>
 #include <linux/percpu-refcount.h>
+#include <linux/cleanup.h>
 
 
 /*
@@ -187,6 +188,8 @@ void kfree_sensitive(const void *);
 size_t __ksize(const void *);
 size_t ksize(const void *);
 
+DEFINE_FREE(kfree, void *, if (_T) kfree(_T))
+
 #ifdef CONFIG_HAVE_HARDENED_USERCOPY_ALLOCATOR
 void __check_heap_object(const void *ptr, unsigned long n, struct page *page,
 			bool to_user);
include/linux/spinlock.h +32 -0
@@ -57,6 +57,7 @@
 #include <linux/stringify.h>
 #include <linux/bottom_half.h>
 #include <linux/lockdep.h>
+#include <linux/cleanup.h>
 #include <asm/barrier.h>
 #include <asm/mmiowb.h>
 
@@ -493,4 +494,35 @@ int __alloc_bucket_spinlocks(spinlock_t
 
 void free_bucket_spinlocks(spinlock_t *locks);
 
+DEFINE_LOCK_GUARD_1(raw_spinlock, raw_spinlock_t,
+		    raw_spin_lock(_T->lock),
+		    raw_spin_unlock(_T->lock))
+
+DEFINE_LOCK_GUARD_1(raw_spinlock_nested, raw_spinlock_t,
+		    raw_spin_lock_nested(_T->lock, SINGLE_DEPTH_NESTING),
+		    raw_spin_unlock(_T->lock))
+
+DEFINE_LOCK_GUARD_1(raw_spinlock_irq, raw_spinlock_t,
+		    raw_spin_lock_irq(_T->lock),
+		    raw_spin_unlock_irq(_T->lock))
+
+DEFINE_LOCK_GUARD_1(raw_spinlock_irqsave, raw_spinlock_t,
+		    raw_spin_lock_irqsave(_T->lock, _T->flags),
+		    raw_spin_unlock_irqrestore(_T->lock, _T->flags),
+		    unsigned long flags)
+
+DEFINE_LOCK_GUARD_1(spinlock, spinlock_t,
+		    spin_lock(_T->lock),
+		    spin_unlock(_T->lock))
+
+DEFINE_LOCK_GUARD_1(spinlock_irq, spinlock_t,
+		    spin_lock_irq(_T->lock),
+		    spin_unlock_irq(_T->lock))
+
+DEFINE_LOCK_GUARD_1(spinlock_irqsave, spinlock_t,
+		    spin_lock_irqsave(_T->lock, _T->flags),
+		    spin_unlock_irqrestore(_T->lock, _T->flags),
+		    unsigned long flags)
+
+#undef __LINUX_INSIDE_SPINLOCK_H
 #endif /* __LINUX_SPINLOCK_H */
include/linux/srcu.h +5 -0
@@ -205,4 +205,9 @@ static inline void smp_mb__after_srcu_re
 	/* __srcu_read_unlock has smp_mb() internally so nothing to do here. */
 }
 
+DEFINE_LOCK_GUARD_1(srcu, struct srcu_struct,
+		    _T->idx = srcu_read_lock(_T->lock),
+		    srcu_read_unlock(_T->lock, _T->idx),
+		    int idx)
+
 #endif
scripts/checkpatch.pl +1 -1
@@ -4522,7 +4522,7 @@ sub process {
 				if|for|while|switch|return|case|
 				volatile|__volatile__|
 				__attribute__|format|__extension__|
-				asm|__asm__)$/x)
+				asm|__asm__|scoped_guard)$/x)
 			{
 			# cpp #define statements have non-optional spaces, ie
 			# if there is a space between the name and the open
author maintainer
#197 lore raw

PATCH 192/332 fscontext: do not consume log entries when returning -EMSGSIZE

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Aleksa Sarai <[email protected]>

[ Upstream commit 72d271a7baa7062cb27e774ac37c5459c6d20e22 ]

Userspace generally expects APIs that return -EMSGSIZE to allow for them to adjust their buffer size and retry the operation. However, the fscontext log would previously clear the message even in the -EMSGSIZE case.

Given that it is very cheap for us to check whether the buffer is too small before we remove the message from the ring buffer, let's just do that instead. While we're at it, refactor some fscontext_read() into a separate helper to make the ring buffer logic a bit easier to read.

Fixes 007ec26cdc9f ("vfs: Implement logging through fs_context")
Cc David Howells <[email protected]>
---
 fs/fsopen.c |   70 ++++++++++++++++++++++++++++++++----------------------------
 1 file changed, 38 insertions(+), 32 deletions(-)
fs/fsopen.c +38 -32
@@ -18,50 +18,56 @@
 #include "internal.h"
 #include "mount.h"
 
+static inline const char *fetch_message_locked(struct fc_log *log, size_t len,
+					       bool *need_free)
+{
+	const char *p;
+	int index;
+
+	if (unlikely(log->head == log->tail))
+		return ERR_PTR(-ENODATA);
+
+	index = log->tail & (ARRAY_SIZE(log->buffer) - 1);
+	p = log->buffer[index];
+	if (unlikely(strlen(p) > len))
+		return ERR_PTR(-EMSGSIZE);
+
+	log->buffer[index] = NULL;
+	*need_free = log->need_free & (1 << index);
+	log->need_free &= ~(1 << index);
+	log->tail++;
+
+	return p;
+}
+
 /*
  * Allow the user to read back any error, warning or informational messages.
+ * Only one message is returned for each read(2) call.
  */
 static ssize_t fscontext_read(struct file *file,
 			      char __user *_buf, size_t len, loff_t *pos)
 {
 	struct fs_context *fc = file->private_data;
-	struct fc_log *log = fc->log.log;
-	unsigned int logsize = ARRAY_SIZE(log->buffer);
-	ssize_t ret;
-	char *p;
+	ssize_t err;
+	const char *p __free(kfree) = NULL, *message;
 	bool need_free;
-	int index, n;
-
-	ret = mutex_lock_interruptible(&fc->uapi_mutex);
-	if (ret < 0)
-		return ret;
-
-	if (log->head == log->tail) {
-		mutex_unlock(&fc->uapi_mutex);
-		return -ENODATA;
-	}
+	int n;
 
-	index = log->tail & (logsize - 1);
-	p = log->buffer[index];
-	need_free = log->need_free & (1 << index);
-	log->buffer[index] = NULL;
-	log->need_free &= ~(1 << index);
-	log->tail++;
+	err = mutex_lock_interruptible(&fc->uapi_mutex);
+	if (err < 0)
+		return err;
+	message = fetch_message_locked(fc->log.log, len, &need_free);
 	mutex_unlock(&fc->uapi_mutex);
+	if (IS_ERR(message))
+		return PTR_ERR(message);
 
-	ret = -EMSGSIZE;
-	n = strlen(p);
-	if (n > len)
-		goto err_free;
-	ret = -EFAULT;
-	if (copy_to_user(_buf, p, n) != 0)
-		goto err_free;
-	ret = n;
-
-err_free:
 	if (need_free)
-		kfree(p);
-	return ret;
+		p = message;
+
+	n = strlen(message);
+	if (copy_to_user(_buf, message, n))
+		return -EFAULT;
+	return n;
 }
 
 static int fscontext_release(struct inode *inode, struct file *file)
author maintainer
#198 lore raw

PATCH 193/332 arm64: mte: Do not flag the zero page as PG_mte_tagged

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Catalin Marinas <[email protected]>

[ Upstream commit f620d66af3165838bfa845dcf9f5f9b4089bf508 ]

Commit 68d54ceeec0e ("arm64: mte: Allow PTRACE_PEEKMTETAGS access to the zero page") attempted to fix ptrace() reading of tags from the zero page by marking it as PG_mte_tagged during cpu_enable_mte(). The same commit also changed the ptrace() tag access permission check to the VM_MTE vma flag while turning the page flag test into a WARN_ON_ONCE().

Attempting to set the PG_mte_tagged flag early with CONFIG_DEFERRED_STRUCT_PAGE_INIT enabled may either hang (after commit d77e59a8fccd "arm64: mte: Lock a page for MTE tag initialisation") or have the flags cleared later during page_alloc_init_late(). In addition, pages_identical() -> memcmp_pages() will reject any comparison with the zero page as it is marked as tagged.

Partially revert the above commit to avoid setting PG_mte_tagged on the zero page. Update the __access_remote_tags() warning on untagged pages to ignore the zero page since it is known to have the tags initialised.

Note that all user mapping of the zero page are marked as pte_special(). The arm64 set_pte_at() will not call mte_sync_tags() on such pages, so PG_mte_tagged will remain cleared.

Fixes 68d54ceeec0e ("arm64: mte: Allow PTRACE_PEEKMTETAGS access to the zero page")
Cc [email protected] # 5.10.x
Cc Will Deacon <[email protected]>
Cc David Hildenbrand <[email protected]>
Cc Lance Yang <[email protected]>
[ replaced is_zero_page() with is_zero_pfn(page_to_pfn()) and folio APIs with page APIs ]
---
 arch/arm64/kernel/cpufeature.c |   10 ++++++++--
 arch/arm64/kernel/mte.c        |    3 ++-
 2 files changed, 10 insertions(+), 3 deletions(-)
arch/arm64/kernel/cpufeature.c +8 -2
@@ -1768,12 +1768,18 @@ static void bti_enable(const struct arm6
 #ifdef CONFIG_ARM64_MTE
 static void cpu_enable_mte(struct arm64_cpu_capabilities const *cap)
 {
+	static bool cleared_zero_page = false;
+
 	/*
 	 * Clear the tags in the zero page. This needs to be done via the
-	 * linear map which has the Tagged attribute.
+	 * linear map which has the Tagged attribute. Since this page is
+	 * always mapped as pte_special(), set_pte_at() will not attempt to
+	 * clear the tags or set PG_mte_tagged.
 	 */
-	if (!test_and_set_bit(PG_mte_tagged, &ZERO_PAGE(0)->flags))
+	if (!cleared_zero_page) {
+		cleared_zero_page = true;
 		mte_clear_page_tags(lm_alias(empty_zero_page));
+	}
 }
 #endif /* CONFIG_ARM64_MTE */
 
arch/arm64/kernel/mte.c +2 -1
@@ -247,7 +247,8 @@ static int __access_remote_tags(struct m
 			put_page(page);
 			break;
 		}
-		WARN_ON_ONCE(!test_bit(PG_mte_tagged, &page->flags));
+		WARN_ON_ONCE(!test_bit(PG_mte_tagged, &page->flags) &&
+			     !is_zero_pfn(page_to_pfn(page)));
 
 		/* limit access to the end of the page */
 		offset = offset_in_page(addr);
author maintainer
#199 lore raw

PATCH 194/332 overflow, tracing: Define the is_signed_type() macro once

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Bart Van Assche <[email protected]>

[ Upstream commit 92d23c6e94157739b997cacce151586a0d07bb8a ]

There are two definitions of the is_signed_type() macro: one in <linux/overflow.h> and a second definition in <linux/trace_events.h>.

As suggested by Linus Torvalds, move the definition of the is_signed_type() macro into the <linux/compiler.h> header file. Change the definition of the is_signed_type() macro to make sure that it does not trigger any sparse warnings with future versions of sparse for bitwise types. See also:
https://lore.kernel.org/all/CAHk-=whjH6p+qzwUdx5SOVVHjS3WvzJQr6mDUwhEyTf6pJWzaQ@mail.gmail.com/
https://lore.kernel.org/all/CAHk-=wjQGnVfb4jehFR0XyZikdQvCZouE96xR_nnf5kqaM5qqQ@mail.gmail.com/

Cc Andrew Morton <[email protected]>
Cc Arnd Bergmann <[email protected]>
Cc Dan Williams <[email protected]>
Cc Eric Dumazet <[email protected]>
Cc Ingo Molnar <[email protected]>
Cc Isabella Basso <[email protected]>
Cc "Jason A. Donenfeld" <[email protected]>
Cc Josh Poimboeuf <[email protected]>
Cc Luc Van Oostenryck <[email protected]>
Cc Masami Hiramatsu <[email protected]>
Cc Nathan Chancellor <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Rasmus Villemoes <[email protected]>
Cc Sander Vanheule <[email protected]>
Cc Steven Rostedt <[email protected]>
Cc Vlastimil Babka <[email protected]>
Cc Yury Norov <[email protected]>
---
 include/linux/compiler.h     |    6 ++++++
 include/linux/overflow.h     |    1 -
 include/linux/trace_events.h |    2 --
 3 files changed, 6 insertions(+), 3 deletions(-)
include/linux/compiler.h +6 -0
@@ -246,6 +246,12 @@ static inline void *offset_to_ptr(const
 #define __must_be_array(a)	BUILD_BUG_ON_ZERO(__same_type((a), &(a)[0]))
 
 /*
+ * Whether 'type' is a signed type or an unsigned type. Supports scalar types,
+ * bool and also pointer types.
+ */
+#define is_signed_type(type) (((type)(-1)) < (__force type)1)
+
+/*
  * This is needed in functions which generate the stack canary, see
  * arch/x86/kernel/smpboot.c::start_secondary() for an example.
  */
include/linux/overflow.h +0 -1
@@ -29,7 +29,6 @@
  * https://mail-index.netbsd.org/tech-misc/2007/02/05/0000.html -
  * credit to Christian Biere.
  */
-#define is_signed_type(type)       (((type)(-1)) < (type)1)
 #define __type_half_max(type) ((type)1 << (8*sizeof(type) - 1 - is_signed_type(type)))
 #define type_max(T) ((T)((__type_half_max(T) - 1) + __type_half_max(T)))
 #define type_min(T) ((T)((T)-type_max(T)-(T)1))
include/linux/trace_events.h +0 -2
@@ -700,8 +700,6 @@ extern int trace_add_event_call(struct t
 extern int trace_remove_event_call(struct trace_event_call *call);
 extern int trace_event_get_offsets(struct trace_event_call *call);
 
-#define is_signed_type(type)	(((type)(-1)) < (type)1)
-
 int ftrace_set_clr_event(struct trace_array *tr, char *buf, int set);
 int trace_set_clr_event(const char *system, const char *event, int set);
 int trace_array_set_clr_event(struct trace_array *tr, const char *system,
author maintainer
#200 lore raw

PATCH 195/332 btrfs: remove duplicated in_range() macro

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Johannes Thumshirn <[email protected]>

[ Upstream commit cea628008fc8c6c9c7b53902f6659e040f33c790 ]

The in_range() macro is defined twice in btrfs' source, once in ctree.h and once in misc.h.

Remove the definition in ctree.h and include misc.h in the files depending on it.

---
 fs/btrfs/ctree.h     |    2 --
 fs/btrfs/extent_io.c |    1 +
 fs/btrfs/file-item.c |    1 +
 fs/btrfs/raid56.c    |    1 +
 4 files changed, 3 insertions(+), 2 deletions(-)
fs/btrfs/ctree.h +0 -2
@@ -3597,8 +3597,6 @@ static inline int btrfs_defrag_cancelled
 	return signal_pending(current);
 }
 
-#define in_range(b, first, len) ((b) >= (first) && (b) < (first) + (len))
-
 /* Sanity test specific functions */
 #ifdef CONFIG_BTRFS_FS_RUN_SANITY_TESTS
 void btrfs_test_destroy_inode(struct inode *inode);
fs/btrfs/extent_io.c +1 -0
@@ -13,6 +13,7 @@
 #include <linux/pagevec.h>
 #include <linux/prefetch.h>
 #include <linux/cleancache.h>
+#include "misc.h"
 #include "extent_io.h"
 #include "extent-io-tree.h"
 #include "extent_map.h"
fs/btrfs/file-item.c +1 -0
@@ -9,6 +9,7 @@
 #include <linux/highmem.h>
 #include <linux/sched/mm.h>
 #include <crypto/hash.h>
+#include "misc.h"
 #include "ctree.h"
 #include "disk-io.h"
 #include "transaction.h"
fs/btrfs/raid56.c +1 -0
@@ -13,6 +13,7 @@
 #include <linux/list_sort.h>
 #include <linux/raid/xor.h>
 #include <linux/mm.h>
+#include "misc.h"
 #include "ctree.h"
 #include "disk-io.h"
 #include "volumes.h"
author maintainer
#201 lore raw

PATCH 196/332 minmax: sanity check constant bounds when clamping

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Jason A. Donenfeld" <[email protected]>

[ Upstream commit 5efcecd9a3b18078d3398b359a84c83f549e22cf ]

The clamp family of functions only makes sense if hi>=lo. If hi and lo are compile-time constants, then raise a build error. Doing so has already caught buggy code. This also introduces the infrastructure to improve the clamping function in subsequent commits.

---
 include/linux/minmax.h |   26 ++++++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)
include/linux/minmax.h +24 -2
@@ -37,6 +37,28 @@
 		__cmp(x, y, op), \
 		__cmp_once(x, y, __UNIQUE_ID(__x), __UNIQUE_ID(__y), op))
 
+#define __clamp(val, lo, hi)	\
+	__cmp(__cmp(val, lo, >), hi, <)
+
+#define __clamp_once(val, lo, hi, unique_val, unique_lo, unique_hi) ({	\
+		typeof(val) unique_val = (val);				\
+		typeof(lo) unique_lo = (lo);				\
+		typeof(hi) unique_hi = (hi);				\
+		__clamp(unique_val, unique_lo, unique_hi); })
+
+#define __clamp_input_check(lo, hi)					\
+        (BUILD_BUG_ON_ZERO(__builtin_choose_expr(			\
+                __is_constexpr((lo) > (hi)), (lo) > (hi), false)))
+
+#define __careful_clamp(val, lo, hi) ({					\
+	__clamp_input_check(lo, hi) +					\
+	__builtin_choose_expr(__typecheck(val, lo) && __typecheck(val, hi) && \
+			      __typecheck(hi, lo) && __is_constexpr(val) && \
+			      __is_constexpr(lo) && __is_constexpr(hi),	\
+		__clamp(val, lo, hi),					\
+		__clamp_once(val, lo, hi, __UNIQUE_ID(__val),		\
+			     __UNIQUE_ID(__lo), __UNIQUE_ID(__hi))); })
+
 /**
  * min - return minimum of two values of the same or compatible types
  * @x: first value
@@ -103,7 +125,7 @@
  * This macro does strict typechecking of @lo/@hi to make sure they are of the
  * same type as @val.  See the unnecessary pointer comparisons.
  */
-#define clamp(val, lo, hi) min((typeof(val))max(val, lo), hi)
+#define clamp(val, lo, hi) __careful_clamp(val, lo, hi)
 
 /*
  * ..and if you can't take the strict
@@ -138,7 +160,7 @@
  * This macro does no typechecking and uses temporary variables of type
  * @type to make all the comparisons.
  */
-#define clamp_t(type, val, lo, hi) min_t(type, max_t(type, val, lo), hi)
+#define clamp_t(type, val, lo, hi) __careful_clamp((type)(val), (type)(lo), (type)(hi))
 
 /**
  * clamp_val - return a value clamped to a given range using val's type
author maintainer
#202 lore raw

PATCH 197/332 minmax: clamp more efficiently by avoiding extra comparison

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Jason A. Donenfeld" <[email protected]>

[ Upstream commit 2122e2a4efc2cd139474079e11939b6e07adfacd ]

Currently the clamp algorithm does:

if (val > hi)
val = hi;
if (val < lo)
val = lo;

But since hi > lo by definition, this can be made more efficient with:

if (val > hi)
val = hi;
else if (val < lo)
val = lo;

So fix up the clamp and clamp_t functions to do this, adding the same argument checking as for min and min_t.

For simple cases, code generation on x86_64 and aarch64 stay about the same:

before:
cmp edi, edx
mov eax, esi
cmova edi, edx
cmp edi, esi
cmovnb eax, edi
ret
after:
cmp edi, esi
mov eax, edx
cmovnb esi, edi
cmp edi, edx
cmovb eax, esi
ret

before:
cmp w0, w2
csel w8, w0, w2, lo
cmp w8, w1
csel w0, w8, w1, hi
ret
after:
cmp w0, w1
csel w8, w0, w1, hi
cmp w0, w2
csel w0, w8, w2, lo
ret

On MIPS64, however, code generation improves, by removing arithmetic in the second branch:

    before:
            sltu    $3,$6,$4
            bne     $3,$0,.L2
            move    $2,$6

            move    $2,$4
    .L2:
            sltu    $3,$2,$5
            bnel    $3,$0,.L7
            move    $2,$5

    .L7:
            jr      $31
            nop
    after:
            sltu    $3,$4,$6
            beq     $3,$0,.L13
            move    $2,$6

            sltu    $3,$4,$5
            bne     $3,$0,.L12
            move    $2,$4

    .L13:
            jr      $31
            nop

    .L12:
            jr      $31
            move    $2,$5

For more complex cases with surrounding code, the effects are a bit more complicated. For example, consider this simplified version of timestamp_truncate() from fs/inode.c on x86_64:

struct timespec64 timestamp_truncate(struct timespec64 t, struct inode *inode) {
struct super_block *sb = inode->i_sb;
unsigned int gran = sb->s_time_gran;

t.tv_sec = clamp(t.tv_sec, sb->s_time_min, sb->s_time_max); if (t.tv_sec == sb->s_time_max || t.tv_sec == sb->s_time_min)
t.tv_nsec = 0;
return t;
}

before:
mov r8, rdx
mov rdx, rsi
mov rcx, QWORD PTR [r8]
mov rax, QWORD PTR [rcx+8]
mov rcx, QWORD PTR [rcx+16]
cmp rax, rdi
mov r8, rcx
cmovge rdi, rax
cmp rdi, rcx
cmovle r8, rdi
cmp rax, r8
je .L4
cmp rdi, rcx
jge .L4
mov rax, r8
ret
.L4:
xor edx, edx
mov rax, r8
ret

after:
mov rax, QWORD PTR [rdx]
mov rdx, QWORD PTR [rax+8]
mov rax, QWORD PTR [rax+16]
cmp rax, rdi
jg .L6
mov r8, rax
xor edx, edx
.L2:
mov rax, r8
ret
.L6:
cmp rdx, rdi
mov r8, rdi
cmovge r8, rdx
cmp rax, r8
je .L4
xor eax, eax
cmp rdx, rdi
cmovl rax, rsi
mov rdx, rax
mov rax, r8
ret
.L4:
xor edx, edx
jmp .L2

In this case, we actually gain a branch, unfortunately, because the compiler's replacement axioms no longer as cleanly apply.

So all and all, this change is a bit of a mixed bag.

---
 include/linux/minmax.h |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/linux/minmax.h +1 -1
@@ -38,7 +38,7 @@
 		__cmp_once(x, y, __UNIQUE_ID(__x), __UNIQUE_ID(__y), op))
 
 #define __clamp(val, lo, hi)	\
-	__cmp(__cmp(val, lo, >), hi, <)
+	((val) >= (hi) ? (hi) : ((val) <= (lo) ? (lo) : (val)))
 
 #define __clamp_once(val, lo, hi, unique_val, unique_lo, unique_hi) ({	\
 		typeof(val) unique_val = (val);				\
author maintainer
#203 lore raw

PATCH 198/332 minmax: add in_range() macro

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: "Matthew Wilcox (Oracle)" <[email protected]>

[ Upstream commit f9bff0e31881d03badf191d3b0005839391f5f2b ]

Patch series "New page table range API", v6.

This patchset changes the API used by the MM to set up page table entries. The four APIs are:

set_ptes(mm, addr, ptep, pte, nr)
update_mmu_cache_range(vma, addr, ptep, nr)
flush_dcache_folio(folio)
flush_icache_pages(vma, page, nr)

flush_dcache_folio() isn't technically new, but no architecture implemented it, so I've done that for them. The old APIs remain around but are mostly implemented by calling the new interfaces.

The new APIs are based around setting up N page table entries at once. The N entries belong to the same PMD, the same folio and the same VMA, so ptep++ is a legitimate operation, and locking is taken care of for you. Some architectures can do a better job of it than just a loop, but I have hesitated to make too deep a change to architectures I don't understand well.

One thing I have changed in every architecture is that PG_arch_1 is now a per-folio bit instead of a per-page bit when used for dcache clean/dirty tracking. This was something that would have to happen eventually, and it makes sense to do it now rather than iterate over every page involved in a cache flush and figure out if it needs to happen.

The point of all this is better performance, and Fengwei Yin has measured improvement on x86. I suspect you'll see improvement on your architecture too. Try the new will-it-scale test mentioned here:
https://lore.kernel.org/linux-mm/[email protected]/
You'll need to run it on an XFS filesystem and have CONFIG_TRANSPARENT_HUGEPAGE set.

This patchset is the basis for much of the anonymous large folio work being done by Ryan, so it's received quite a lot of testing over the last few months.

This patch (of 38):

Determine if a value lies within a range more efficiently (subtraction + comparison vs two comparisons and an AND). It also has useful (under some circumstances) behaviour if the range exceeds the maximum value of the type. Convert all the conflicting definitions of in_range() within the kernel; some can use the generic definition while others need their own definition.

---
 arch/arm/mm/pageattr.c                                     |    6 +-
 drivers/gpu/drm/arm/display/include/malidp_utils.h         |    2 
 drivers/gpu/drm/arm/display/komeda/komeda_pipeline_state.c |   24 +++++------
 drivers/gpu/drm/msm/adreno/a6xx_gmu.c                      |    6 --
 drivers/net/ethernet/chelsio/cxgb3/cxgb3_main.c            |   18 ++++----
 fs/btrfs/misc.h                                            |    2 
 fs/ext2/balloc.c                                           |    2 
 fs/ext4/ext4.h                                             |    2 
 fs/ufs/util.h                                              |    6 --
 include/linux/minmax.h                                     |   27 +++++++++++++
 lib/logic_pio.c                                            |    3 -
 net/netfilter/nf_nat_core.c                                |    6 +-
 net/tipc/core.h                                            |    2 
 net/tipc/link.c                                            |   10 ++--
 14 files changed, 61 insertions(+), 55 deletions(-)
arch/arm/mm/pageattr.c +3 -3
@@ -25,7 +25,7 @@ static int change_page_range(pte_t *ptep
 	return 0;
 }
 
-static bool in_range(unsigned long start, unsigned long size,
+static bool range_in_range(unsigned long start, unsigned long size,
 	unsigned long range_start, unsigned long range_end)
 {
 	return start >= range_start && start < range_end &&
@@ -46,8 +46,8 @@ static int change_memory_common(unsigned
 	if (!size)
 		return 0;
 
-	if (!in_range(start, size, MODULES_VADDR, MODULES_END) &&
-	    !in_range(start, size, VMALLOC_START, VMALLOC_END))
+	if (!range_in_range(start, size, MODULES_VADDR, MODULES_END) &&
+	    !range_in_range(start, size, VMALLOC_START, VMALLOC_END))
 		return -EINVAL;
 
 	data.set_mask = set_mask;
drivers/gpu/drm/arm/display/include/malidp_utils.h +1 -1
@@ -35,7 +35,7 @@ static inline void set_range(struct mali
 	rg->end   = end;
 }
 
-static inline bool in_range(struct malidp_range *rg, u32 v)
+static inline bool malidp_in_range(struct malidp_range *rg, u32 v)
 {
 	return (v >= rg->start) && (v <= rg->end);
 }
drivers/gpu/drm/arm/display/komeda/komeda_pipeline_state.c +12 -12
@@ -305,12 +305,12 @@ komeda_layer_check_cfg(struct komeda_lay
 	if (komeda_fb_check_src_coords(kfb, src_x, src_y, src_w, src_h))
 		return -EINVAL;
 
-	if (!in_range(&layer->hsize_in, src_w)) {
+	if (!malidp_in_range(&layer->hsize_in, src_w)) {
 		DRM_DEBUG_ATOMIC("invalidate src_w %d.\n", src_w);
 		return -EINVAL;
 	}
 
-	if (!in_range(&layer->vsize_in, src_h)) {
+	if (!malidp_in_range(&layer->vsize_in, src_h)) {
 		DRM_DEBUG_ATOMIC("invalidate src_h %d.\n", src_h);
 		return -EINVAL;
 	}
@@ -452,14 +452,14 @@ komeda_scaler_check_cfg(struct komeda_sc
 	hsize_out = dflow->out_w;
 	vsize_out = dflow->out_h;
 
-	if (!in_range(&scaler->hsize, hsize_in) ||
-	    !in_range(&scaler->hsize, hsize_out)) {
+	if (!malidp_in_range(&scaler->hsize, hsize_in) ||
+	    !malidp_in_range(&scaler->hsize, hsize_out)) {
 		DRM_DEBUG_ATOMIC("Invalid horizontal sizes");
 		return -EINVAL;
 	}
 
-	if (!in_range(&scaler->vsize, vsize_in) ||
-	    !in_range(&scaler->vsize, vsize_out)) {
+	if (!malidp_in_range(&scaler->vsize, vsize_in) ||
+	    !malidp_in_range(&scaler->vsize, vsize_out)) {
 		DRM_DEBUG_ATOMIC("Invalid vertical sizes");
 		return -EINVAL;
 	}
@@ -574,13 +574,13 @@ komeda_splitter_validate(struct komeda_s
 		return -EINVAL;
 	}
 
-	if (!in_range(&splitter->hsize, dflow->in_w)) {
+	if (!malidp_in_range(&splitter->hsize, dflow->in_w)) {
 		DRM_DEBUG_ATOMIC("split in_w:%d is out of the acceptable range.\n",
 				 dflow->in_w);
 		return -EINVAL;
 	}
 
-	if (!in_range(&splitter->vsize, dflow->in_h)) {
+	if (!malidp_in_range(&splitter->vsize, dflow->in_h)) {
 		DRM_DEBUG_ATOMIC("split in_h: %d exceeds the acceptable range.\n",
 				 dflow->in_h);
 		return -EINVAL;
@@ -624,13 +624,13 @@ komeda_merger_validate(struct komeda_mer
 		return -EINVAL;
 	}
 
-	if (!in_range(&merger->hsize_merged, output->out_w)) {
+	if (!malidp_in_range(&merger->hsize_merged, output->out_w)) {
 		DRM_DEBUG_ATOMIC("merged_w: %d is out of the accepted range.\n",
 				 output->out_w);
 		return -EINVAL;
 	}
 
-	if (!in_range(&merger->vsize_merged, output->out_h)) {
+	if (!malidp_in_range(&merger->vsize_merged, output->out_h)) {
 		DRM_DEBUG_ATOMIC("merged_h: %d is out of the accepted range.\n",
 				 output->out_h);
 		return -EINVAL;
@@ -866,8 +866,8 @@ void komeda_complete_data_flow_cfg(struc
 	 * input/output range.
 	 */
 	if (dflow->en_scaling && scaler)
-		dflow->en_split = !in_range(&scaler->hsize, dflow->in_w) ||
-				  !in_range(&scaler->hsize, dflow->out_w);
+		dflow->en_split = !malidp_in_range(&scaler->hsize, dflow->in_w) ||
+				  !malidp_in_range(&scaler->hsize, dflow->out_w);
 }
 
 static bool merger_is_available(struct komeda_pipeline *pipe,
drivers/gpu/drm/msm/adreno/a6xx_gmu.c +0 -6
@@ -657,12 +657,6 @@ struct block_header {
 	u32 data[];
 };
 
-/* this should be a general kernel helper */
-static int in_range(u32 addr, u32 start, u32 size)
-{
-	return addr >= start && addr < start + size;
-}
-
 static bool fw_block_mem(struct a6xx_gmu_bo *bo, const struct block_header *blk)
 {
 	if (!in_range(blk->addr, bo->iova, bo->size))
drivers/net/ethernet/chelsio/cxgb3/cxgb3_main.c +9 -9
@@ -2131,7 +2131,7 @@ static const struct ethtool_ops cxgb_eth
 	.set_link_ksettings = set_link_ksettings,
 };
 
-static int in_range(int val, int lo, int hi)
+static int cxgb_in_range(int val, int lo, int hi)
 {
 	return val < 0 || (val <= hi && val >= lo);
 }
@@ -2162,19 +2162,19 @@ static int cxgb_extension_ioctl(struct n
 			return -EINVAL;
 		if (t.qset_idx >= SGE_QSETS)
 			return -EINVAL;
-		if (!in_range(t.intr_lat, 0, M_NEWTIMER) ||
-		    !in_range(t.cong_thres, 0, 255) ||
-		    !in_range(t.txq_size[0], MIN_TXQ_ENTRIES,
+		if (!cxgb_in_range(t.intr_lat, 0, M_NEWTIMER) ||
+		    !cxgb_in_range(t.cong_thres, 0, 255) ||
+		    !cxgb_in_range(t.txq_size[0], MIN_TXQ_ENTRIES,
 			      MAX_TXQ_ENTRIES) ||
-		    !in_range(t.txq_size[1], MIN_TXQ_ENTRIES,
+		    !cxgb_in_range(t.txq_size[1], MIN_TXQ_ENTRIES,
 			      MAX_TXQ_ENTRIES) ||
-		    !in_range(t.txq_size[2], MIN_CTRL_TXQ_ENTRIES,
+		    !cxgb_in_range(t.txq_size[2], MIN_CTRL_TXQ_ENTRIES,
 			      MAX_CTRL_TXQ_ENTRIES) ||
-		    !in_range(t.fl_size[0], MIN_FL_ENTRIES,
+		    !cxgb_in_range(t.fl_size[0], MIN_FL_ENTRIES,
 			      MAX_RX_BUFFERS) ||
-		    !in_range(t.fl_size[1], MIN_FL_ENTRIES,
+		    !cxgb_in_range(t.fl_size[1], MIN_FL_ENTRIES,
 			      MAX_RX_JUMBO_BUFFERS) ||
-		    !in_range(t.rspq_size, MIN_RSPQ_ENTRIES,
+		    !cxgb_in_range(t.rspq_size, MIN_RSPQ_ENTRIES,
 			      MAX_RSPQ_ENTRIES))
 			return -EINVAL;
 
fs/btrfs/misc.h +0 -2
@@ -8,8 +8,6 @@
 #include <asm/div64.h>
 #include <linux/rbtree.h>
 
-#define in_range(b, first, len) ((b) >= (first) && (b) < (first) + (len))
-
 static inline void cond_wake_up(struct wait_queue_head *wq)
 {
 	/*
fs/ext2/balloc.c +0 -2
@@ -36,8 +36,6 @@
  */
 
 
-#define in_range(b, first, len)	((b) >= (first) && (b) <= (first) + (len) - 1)
-
 struct ext2_group_desc * ext2_get_group_desc(struct super_block * sb,
 					     unsigned int block_group,
 					     struct buffer_head ** bh)
fs/ext4/ext4.h +0 -2
@@ -3659,8 +3659,6 @@ static inline void set_bitmap_uptodate(s
 	set_bit(BH_BITMAP_UPTODATE, &(bh)->b_state);
 }
 
-#define in_range(b, first, len)	((b) >= (first) && (b) <= (first) + (len) - 1)
-
 /* For ioend & aio unwritten conversion wait queues */
 #define EXT4_WQ_HASH_SZ		37
 #define ext4_ioend_wq(v)   (&ext4__ioend_wq[((unsigned long)(v)) %\
fs/ufs/util.h +0 -6
@@ -11,12 +11,6 @@
 #include <linux/fs.h>
 #include "swab.h"
 
-
-/*
- * some useful macros
- */
-#define in_range(b,first,len)	((b)>=(first)&&(b)<(first)+(len))
-
 /*
  * functions used for retyping
  */
include/linux/minmax.h +27 -0
@@ -3,6 +3,7 @@
 #define _LINUX_MINMAX_H
 
 #include <linux/const.h>
+#include <linux/types.h>
 
 /*
  * min()/max()/clamp() macros must accomplish three things:
@@ -175,6 +176,32 @@
  */
 #define clamp_val(val, lo, hi) clamp_t(typeof(val), val, lo, hi)
 
+static inline bool in_range64(u64 val, u64 start, u64 len)
+{
+	return (val - start) < len;
+}
+
+static inline bool in_range32(u32 val, u32 start, u32 len)
+{
+	return (val - start) < len;
+}
+
+/**
+ * in_range - Determine if a value lies within a range.
+ * @val: Value to test.
+ * @start: First value in range.
+ * @len: Number of values in range.
+ *
+ * This is more efficient than "if (start <= val && val < (start + len))".
+ * It also gives a different answer if @start + @len overflows the size of
+ * the type by a sufficient amount to encompass @val.  Decide for yourself
+ * which behaviour you want, or prove that start + len never overflow.
+ * Do not blindly replace one form with the other.
+ */
+#define in_range(val, start, len)					\
+	((sizeof(start) | sizeof(len) | sizeof(val)) <= sizeof(u32) ?	\
+		in_range32(val, start, len) : in_range64(val, start, len))
+
 /**
  * swap - swap values of @a and @b
  * @a: first value
lib/logic_pio.c +0 -3
@@ -20,9 +20,6 @@
 static LIST_HEAD(io_range_list);
 static DEFINE_MUTEX(io_range_mutex);
 
-/* Consider a kernel general helper for this */
-#define in_range(b, first, len)        ((b) >= (first) && (b) < (first) + (len))
-
 /**
  * logic_pio_register_range - register logical PIO range for a host
  * @new_range: pointer to the IO range to be registered.
net/netfilter/nf_nat_core.c +3 -3
@@ -262,7 +262,7 @@ static bool l4proto_in_range(const struc
 /* If we source map this tuple so reply looks like reply_tuple, will
  * that meet the constraints of range.
  */
-static int in_range(const struct nf_conntrack_tuple *tuple,
+static int nf_in_range(const struct nf_conntrack_tuple *tuple,
 		    const struct nf_nat_range2 *range)
 {
 	/* If we are supposed to map IPs, then we must be in the
@@ -311,7 +311,7 @@ find_appropriate_src(struct net *net,
 				       &ct->tuplehash[IP_CT_DIR_REPLY].tuple);
 			result->dst = tuple->dst;
 
-			if (in_range(result, range))
+			if (nf_in_range(result, range))
 				return 1;
 		}
 	}
@@ -543,7 +543,7 @@ get_unique_tuple(struct nf_conntrack_tup
 	if (maniptype == NF_NAT_MANIP_SRC &&
 	    !(range->flags & NF_NAT_RANGE_PROTO_RANDOM_ALL)) {
 		/* try the original tuple first */
-		if (in_range(orig_tuple, range)) {
+		if (nf_in_range(orig_tuple, range)) {
 			if (!nf_nat_used_tuple(orig_tuple, ct)) {
 				*tuple = *orig_tuple;
 				return;
net/tipc/core.h +1 -1
@@ -199,7 +199,7 @@ static inline int less(u16 left, u16 rig
 	return less_eq(left, right) && (mod(right) != mod(left));
 }
 
-static inline int in_range(u16 val, u16 min, u16 max)
+static inline int tipc_in_range(u16 val, u16 min, u16 max)
 {
 	return !less(val, min) && !more(val, max);
 }
net/tipc/link.c +5 -5
@@ -1588,7 +1588,7 @@ next_gap_ack:
 					  last_ga->bgack_cnt);
 			}
 			/* Check against the last Gap ACK block */
-			if (in_range(seqno, start, end))
+			if (tipc_in_range(seqno, start, end))
 				continue;
 			/* Update/release the packet peer is acking */
 			bc_has_acked = true;
@@ -2216,12 +2216,12 @@ static int tipc_link_proto_rcv(struct ti
 		strncpy(if_name, data, TIPC_MAX_IF_NAME);
 
 		/* Update own tolerance if peer indicates a non-zero value */
-		if (in_range(peers_tol, TIPC_MIN_LINK_TOL, TIPC_MAX_LINK_TOL)) {
+		if (tipc_in_range(peers_tol, TIPC_MIN_LINK_TOL, TIPC_MAX_LINK_TOL)) {
 			l->tolerance = peers_tol;
 			l->bc_rcvlink->tolerance = peers_tol;
 		}
 		/* Update own priority if peer's priority is higher */
-		if (in_range(peers_prio, l->priority + 1, TIPC_MAX_LINK_PRI))
+		if (tipc_in_range(peers_prio, l->priority + 1, TIPC_MAX_LINK_PRI))
 			l->priority = peers_prio;
 
 		/* If peer is going down we want full re-establish cycle */
@@ -2264,13 +2264,13 @@ static int tipc_link_proto_rcv(struct ti
 		l->rcv_nxt_state = msg_seqno(hdr) + 1;
 
 		/* Update own tolerance if peer indicates a non-zero value */
-		if (in_range(peers_tol, TIPC_MIN_LINK_TOL, TIPC_MAX_LINK_TOL)) {
+		if (tipc_in_range(peers_tol, TIPC_MIN_LINK_TOL, TIPC_MAX_LINK_TOL)) {
 			l->tolerance = peers_tol;
 			l->bc_rcvlink->tolerance = peers_tol;
 		}
 		/* Update own prio if peer indicates a different value */
 		if ((peers_prio != l->priority) &&
-		    in_range(peers_prio, 1, TIPC_MAX_LINK_PRI)) {
+		    tipc_in_range(peers_prio, 1, TIPC_MAX_LINK_PRI)) {
 			l->priority = peers_prio;
 			rc = tipc_link_fsm_evt(l, LINK_FAILURE_EVT);
 		}
author maintainer
#204 lore raw

PATCH 199/332 minmax: Introduce {min,max}_array()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Herve Codina <[email protected]>

[ Upstream commit c952c748c7a983a8bda9112984e6f2c1f6e441a5 ]

Introduce min_array() (resp max_array()) in order to get the minimal (resp maximum) of values present in an array.

---
 include/linux/minmax.h |   64 +++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)
include/linux/minmax.h +64 -0
@@ -151,6 +151,70 @@
  */
 #define max_t(type, x, y)	__careful_cmp((type)(x), (type)(y), >)
 
+/*
+ * Remove a const qualifier from integer types
+ * _Generic(foo, type-name: association, ..., default: association) performs a
+ * comparison against the foo type (not the qualified type).
+ * Do not use the const keyword in the type-name as it will not match the
+ * unqualified type of foo.
+ */
+#define __unconst_integer_type_cases(type)	\
+	unsigned type:  (unsigned type)0,	\
+	signed type:    (signed type)0
+
+#define __unconst_integer_typeof(x) typeof(			\
+	_Generic((x),						\
+		char: (char)0,					\
+		__unconst_integer_type_cases(char),		\
+		__unconst_integer_type_cases(short),		\
+		__unconst_integer_type_cases(int),		\
+		__unconst_integer_type_cases(long),		\
+		__unconst_integer_type_cases(long long),	\
+		default: (x)))
+
+/*
+ * Do not check the array parameter using __must_be_array().
+ * In the following legit use-case where the "array" passed is a simple pointer,
+ * __must_be_array() will return a failure.
+ * --- 8< ---
+ * int *buff
+ * ...
+ * min = min_array(buff, nb_items);
+ * --- 8< ---
+ *
+ * The first typeof(&(array)[0]) is needed in order to support arrays of both
+ * 'int *buff' and 'int buff[N]' types.
+ *
+ * The array can be an array of const items.
+ * typeof() keeps the const qualifier. Use __unconst_integer_typeof() in order
+ * to discard the const qualifier for the __element variable.
+ */
+#define __minmax_array(op, array, len) ({				\
+	typeof(&(array)[0]) __array = (array);				\
+	typeof(len) __len = (len);					\
+	__unconst_integer_typeof(__array[0]) __element = __array[--__len]; \
+	while (__len--)							\
+		__element = op(__element, __array[__len]);		\
+	__element; })
+
+/**
+ * min_array - return minimum of values present in an array
+ * @array: array
+ * @len: array length
+ *
+ * Note that @len must not be zero (empty array).
+ */
+#define min_array(array, len) __minmax_array(min, array, len)
+
+/**
+ * max_array - return maximum of values present in an array
+ * @array: array
+ * @len: array length
+ *
+ * Note that @len must not be zero (empty array).
+ */
+#define max_array(array, len) __minmax_array(max, array, len)
+
 /**
  * clamp_t - return a value clamped to a given range using a given type
  * @type: the type of variable to use
author maintainer
#205 lore raw

PATCH 200/332 minmax: deduplicate __unconst_integer_typeof()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Andy Shevchenko <[email protected]>

[ Upstream commit 5e57418a2031cd5e1863efdf3d7447a16a368172 ]

It appears that compiler_types.h already have an implementation of the __unconst_integer_typeof() called __unqual_scalar_typeof(). Use it instead of the copy.

---
 include/linux/minmax.h |   26 +++-----------------------
 1 file changed, 3 insertions(+), 23 deletions(-)
include/linux/minmax.h +3 -23
@@ -2,6 +2,7 @@
 #ifndef _LINUX_MINMAX_H
 #define _LINUX_MINMAX_H
 
+#include <linux/compiler_types.h>
 #include <linux/const.h>
 #include <linux/types.h>
 
@@ -152,27 +153,6 @@
 #define max_t(type, x, y)	__careful_cmp((type)(x), (type)(y), >)
 
 /*
- * Remove a const qualifier from integer types
- * _Generic(foo, type-name: association, ..., default: association) performs a
- * comparison against the foo type (not the qualified type).
- * Do not use the const keyword in the type-name as it will not match the
- * unqualified type of foo.
- */
-#define __unconst_integer_type_cases(type)	\
-	unsigned type:  (unsigned type)0,	\
-	signed type:    (signed type)0
-
-#define __unconst_integer_typeof(x) typeof(			\
-	_Generic((x),						\
-		char: (char)0,					\
-		__unconst_integer_type_cases(char),		\
-		__unconst_integer_type_cases(short),		\
-		__unconst_integer_type_cases(int),		\
-		__unconst_integer_type_cases(long),		\
-		__unconst_integer_type_cases(long long),	\
-		default: (x)))
-
-/*
  * Do not check the array parameter using __must_be_array().
  * In the following legit use-case where the "array" passed is a simple pointer,
  * __must_be_array() will return a failure.
@@ -186,13 +166,13 @@
  * 'int *buff' and 'int buff[N]' types.
  *
  * The array can be an array of const items.
- * typeof() keeps the const qualifier. Use __unconst_integer_typeof() in order
+ * typeof() keeps the const qualifier. Use __unqual_scalar_typeof() in order
  * to discard the const qualifier for the __element variable.
  */
 #define __minmax_array(op, array, len) ({				\
 	typeof(&(array)[0]) __array = (array);				\
 	typeof(len) __len = (len);					\
-	__unconst_integer_typeof(__array[0]) __element = __array[--__len]; \
+	__unqual_scalar_typeof(__array[0]) __element = __array[--__len];\
 	while (__len--)							\
 		__element = op(__element, __array[__len]);		\
 	__element; })
author maintainer
#206 lore raw

PATCH 201/332 minmax: fix header inclusions

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Andy Shevchenko <[email protected]>

[ Upstream commit f6e9d38f8eb00ac8b52e6d15f6aa9bcecacb081b ]

BUILD_BUG_ON*() macros are defined in build_bug.h. Include it. Replace compiler_types.h by compiler.h, which provides the former, to have a definition of the __UNIQUE_ID().

---
 include/linux/minmax.h |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
include/linux/minmax.h +2 -1
@@ -2,7 +2,8 @@
 #ifndef _LINUX_MINMAX_H
 #define _LINUX_MINMAX_H
 
-#include <linux/compiler_types.h>
+#include <linux/build_bug.h>
+#include <linux/compiler.h>
 #include <linux/const.h>
 #include <linux/types.h>
 
author maintainer
#207 lore raw

PATCH 202/332 minmax: allow min()/max()/clamp() if the arguments have the same signedness.

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Laight <[email protected]>

[ Upstream commit d03eba99f5bf7cbc6e2fdde3b6fa36954ad58e09 ]

The type-check in min()/max() is there to stop unexpected results if a negative value gets converted to a large unsigned value. However it also rejects 'unsigned int' v 'unsigned long' compares which are common and never problematc.

Replace the 'same type' check with a 'same signedness' check.

The new test isn't itself a compile time error, so use static_assert() to report the error and give a meaningful error message.

Due to the way builtin_choose_expr() works detecting the error in the 'non-constant' side (where static_assert() can be used) also detects errors when the arguments are constant.

---
 include/linux/minmax.h |   62 ++++++++++++++++++++++++++-----------------------
 1 file changed, 33 insertions(+), 29 deletions(-)
include/linux/minmax.h +33 -29
@@ -12,9 +12,8 @@
  *
  * - avoid multiple evaluations of the arguments (so side-effects like
  *   "x++" happen only once) when non-constant.
- * - perform strict type-checking (to generate warnings instead of
- *   nasty runtime surprises). See the "unnecessary" pointer comparison
- *   in __typecheck().
+ * - perform signed v unsigned type-checking (to generate compile
+ *   errors instead of nasty runtime surprises).
  * - retain result as a constant expressions when called with only
  *   constant expressions (to avoid tripping VLA warnings in stack
  *   allocation usage).
@@ -22,23 +21,30 @@
 #define __typecheck(x, y) \
 	(!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
 
-#define __no_side_effects(x, y) \
-		(__is_constexpr(x) && __is_constexpr(y))
+/* is_signed_type() isn't a constexpr for pointer types */
+#define __is_signed(x) 								\
+	__builtin_choose_expr(__is_constexpr(is_signed_type(typeof(x))),	\
+		is_signed_type(typeof(x)), 0)
 
-#define __safe_cmp(x, y) \
-		(__typecheck(x, y) && __no_side_effects(x, y))
+#define __types_ok(x, y) \
+	(__is_signed(x) == __is_signed(y))
 
-#define __cmp(x, y, op)	((x) op (y) ? (x) : (y))
+#define __cmp_op_min <
+#define __cmp_op_max >
 
-#define __cmp_once(x, y, unique_x, unique_y, op) ({	\
+#define __cmp(op, x, y)	((x) __cmp_op_##op (y) ? (x) : (y))
+
+#define __cmp_once(op, x, y, unique_x, unique_y) ({	\
 		typeof(x) unique_x = (x);		\
 		typeof(y) unique_y = (y);		\
-		__cmp(unique_x, unique_y, op); })
-
-#define __careful_cmp(x, y, op) \
-	__builtin_choose_expr(__safe_cmp(x, y), \
-		__cmp(x, y, op), \
-		__cmp_once(x, y, __UNIQUE_ID(__x), __UNIQUE_ID(__y), op))
+		static_assert(__types_ok(x, y),		\
+			#op "(" #x ", " #y ") signedness error, fix types or consider u" #op "() before " #op "_t()"); \
+		__cmp(op, unique_x, unique_y); })
+
+#define __careful_cmp(op, x, y)					\
+	__builtin_choose_expr(__is_constexpr((x) - (y)),	\
+		__cmp(op, x, y),				\
+		__cmp_once(op, x, y, __UNIQUE_ID(__x), __UNIQUE_ID(__y)))
 
 #define __clamp(val, lo, hi)	\
 	((val) >= (hi) ? (hi) : ((val) <= (lo) ? (lo) : (val)))
@@ -47,17 +53,15 @@
 		typeof(val) unique_val = (val);				\
 		typeof(lo) unique_lo = (lo);				\
 		typeof(hi) unique_hi = (hi);				\
+		static_assert(__builtin_choose_expr(__is_constexpr((lo) > (hi)), 	\
+				(lo) <= (hi), true),					\
+			"clamp() low limit " #lo " greater than high limit " #hi);	\
+		static_assert(__types_ok(val, lo), "clamp() 'lo' signedness error");	\
+		static_assert(__types_ok(val, hi), "clamp() 'hi' signedness error");	\
 		__clamp(unique_val, unique_lo, unique_hi); })
 
-#define __clamp_input_check(lo, hi)					\
-        (BUILD_BUG_ON_ZERO(__builtin_choose_expr(			\
-                __is_constexpr((lo) > (hi)), (lo) > (hi), false)))
-
 #define __careful_clamp(val, lo, hi) ({					\
-	__clamp_input_check(lo, hi) +					\
-	__builtin_choose_expr(__typecheck(val, lo) && __typecheck(val, hi) && \
-			      __typecheck(hi, lo) && __is_constexpr(val) && \
-			      __is_constexpr(lo) && __is_constexpr(hi),	\
+	__builtin_choose_expr(__is_constexpr((val) - (lo) + (hi)),	\
 		__clamp(val, lo, hi),					\
 		__clamp_once(val, lo, hi, __UNIQUE_ID(__val),		\
 			     __UNIQUE_ID(__lo), __UNIQUE_ID(__hi))); })
@@ -67,14 +71,14 @@
  * @x: first value
  * @y: second value
  */
-#define min(x, y)	__careful_cmp(x, y, <)
+#define min(x, y)	__careful_cmp(min, x, y)
 
 /**
  * max - return maximum of two values of the same or compatible types
  * @x: first value
  * @y: second value
  */
-#define max(x, y)	__careful_cmp(x, y, >)
+#define max(x, y)	__careful_cmp(max, x, y)
 
 /**
  * umin - return minimum of two non-negative values
@@ -83,7 +87,7 @@
  * @y: second value
  */
 #define umin(x, y)	\
-	__careful_cmp((x) + 0u + 0ul + 0ull, (y) + 0u + 0ul + 0ull, <)
+	__careful_cmp(min, (x) + 0u + 0ul + 0ull, (y) + 0u + 0ul + 0ull)
 
 /**
  * umax - return maximum of two non-negative values
@@ -91,7 +95,7 @@
  * @y: second value
  */
 #define umax(x, y)	\
-	__careful_cmp((x) + 0u + 0ul + 0ull, (y) + 0u + 0ul + 0ull, >)
+	__careful_cmp(max, (x) + 0u + 0ul + 0ull, (y) + 0u + 0ul + 0ull)
 
 /**
  * min3 - return minimum of three values
@@ -143,7 +147,7 @@
  * @x: first value
  * @y: second value
  */
-#define min_t(type, x, y)	__careful_cmp((type)(x), (type)(y), <)
+#define min_t(type, x, y)	__careful_cmp(min, (type)(x), (type)(y))
 
 /**
  * max_t - return maximum of two values, using the specified type
@@ -151,7 +155,7 @@
  * @x: first value
  * @y: second value
  */
-#define max_t(type, x, y)	__careful_cmp((type)(x), (type)(y), >)
+#define max_t(type, x, y)	__careful_cmp(max, (type)(x), (type)(y))
 
 /*
  * Do not check the array parameter using __must_be_array().
author maintainer
#208 lore raw

PATCH 203/332 minmax: fix indentation of __cmp_once() and __clamp_once()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Laight <[email protected]>

[ Upstream commit f4b84b2ff851f01d0fac619eadef47eb41648534 ]

Remove the extra indentation and align continuation markers.

---
 include/linux/minmax.h |   30 +++++++++++++++---------------
 1 file changed, 15 insertions(+), 15 deletions(-)
include/linux/minmax.h +15 -15
@@ -35,11 +35,11 @@
 #define __cmp(op, x, y)	((x) __cmp_op_##op (y) ? (x) : (y))
 
 #define __cmp_once(op, x, y, unique_x, unique_y) ({	\
-		typeof(x) unique_x = (x);		\
-		typeof(y) unique_y = (y);		\
-		static_assert(__types_ok(x, y),		\
-			#op "(" #x ", " #y ") signedness error, fix types or consider u" #op "() before " #op "_t()"); \
-		__cmp(op, unique_x, unique_y); })
+	typeof(x) unique_x = (x);			\
+	typeof(y) unique_y = (y);			\
+	static_assert(__types_ok(x, y),			\
+		#op "(" #x ", " #y ") signedness error, fix types or consider u" #op "() before " #op "_t()"); \
+	__cmp(op, unique_x, unique_y); })
 
 #define __careful_cmp(op, x, y)					\
 	__builtin_choose_expr(__is_constexpr((x) - (y)),	\
@@ -49,16 +49,16 @@
 #define __clamp(val, lo, hi)	\
 	((val) >= (hi) ? (hi) : ((val) <= (lo) ? (lo) : (val)))
 
-#define __clamp_once(val, lo, hi, unique_val, unique_lo, unique_hi) ({	\
-		typeof(val) unique_val = (val);				\
-		typeof(lo) unique_lo = (lo);				\
-		typeof(hi) unique_hi = (hi);				\
-		static_assert(__builtin_choose_expr(__is_constexpr((lo) > (hi)), 	\
-				(lo) <= (hi), true),					\
-			"clamp() low limit " #lo " greater than high limit " #hi);	\
-		static_assert(__types_ok(val, lo), "clamp() 'lo' signedness error");	\
-		static_assert(__types_ok(val, hi), "clamp() 'hi' signedness error");	\
-		__clamp(unique_val, unique_lo, unique_hi); })
+#define __clamp_once(val, lo, hi, unique_val, unique_lo, unique_hi) ({		\
+	typeof(val) unique_val = (val);						\
+	typeof(lo) unique_lo = (lo);						\
+	typeof(hi) unique_hi = (hi);						\
+	static_assert(__builtin_choose_expr(__is_constexpr((lo) > (hi)), 	\
+			(lo) <= (hi), true),					\
+		"clamp() low limit " #lo " greater than high limit " #hi);	\
+	static_assert(__types_ok(val, lo), "clamp() 'lo' signedness error");	\
+	static_assert(__types_ok(val, hi), "clamp() 'hi' signedness error");	\
+	__clamp(unique_val, unique_lo, unique_hi); })
 
 #define __careful_clamp(val, lo, hi) ({					\
 	__builtin_choose_expr(__is_constexpr((val) - (lo) + (hi)),	\
author maintainer
#209 lore raw

PATCH 204/332 minmax: allow comparisons of int against unsigned char/short

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Laight <[email protected]>

[ Upstream commit 4ead534fba42fc4fd41163297528d2aa731cd121 ]

Since 'unsigned char/short' get promoted to 'signed int' it is safe to compare them against an 'int' value.

---
 include/linux/minmax.h |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
include/linux/minmax.h +3 -2
@@ -26,8 +26,9 @@
 	__builtin_choose_expr(__is_constexpr(is_signed_type(typeof(x))),	\
 		is_signed_type(typeof(x)), 0)
 
-#define __types_ok(x, y) \
-	(__is_signed(x) == __is_signed(y))
+#define __types_ok(x, y) 			\
+	(__is_signed(x) == __is_signed(y) ||	\
+		__is_signed((x) + 0) == __is_signed((y) + 0))
 
 #define __cmp_op_min <
 #define __cmp_op_max >
author maintainer
#210 lore raw

PATCH 205/332 minmax: relax check to allow comparison between unsigned arguments and signed constants

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Laight <[email protected]>

[ Upstream commit 867046cc7027703f60a46339ffde91a1970f2901 ]

Allow (for example) min(unsigned_var, 20).

The opposite min(signed_var, 20u) is still errored.

Since a comparison between signed and unsigned never makes the unsigned value negative it is only necessary to adjust the __types_ok() test.

---
 include/linux/minmax.h |   24 +++++++++++++++++-------
 1 file changed, 17 insertions(+), 7 deletions(-)
include/linux/minmax.h +17 -7
@@ -10,13 +10,18 @@
 /*
  * min()/max()/clamp() macros must accomplish three things:
  *
- * - avoid multiple evaluations of the arguments (so side-effects like
+ * - Avoid multiple evaluations of the arguments (so side-effects like
  *   "x++" happen only once) when non-constant.
- * - perform signed v unsigned type-checking (to generate compile
- *   errors instead of nasty runtime surprises).
- * - retain result as a constant expressions when called with only
+ * - Retain result as a constant expressions when called with only
  *   constant expressions (to avoid tripping VLA warnings in stack
  *   allocation usage).
+ * - Perform signed v unsigned type-checking (to generate compile
+ *   errors instead of nasty runtime surprises).
+ * - Unsigned char/short are always promoted to signed int and can be
+ *   compared against signed or unsigned arguments.
+ * - Unsigned arguments can be compared against non-negative signed constants.
+ * - Comparison of a signed argument against an unsigned constant fails
+ *   even if the constant is below __INT_MAX__ and could be cast to int.
  */
 #define __typecheck(x, y) \
 	(!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
@@ -26,9 +31,14 @@
 	__builtin_choose_expr(__is_constexpr(is_signed_type(typeof(x))),	\
 		is_signed_type(typeof(x)), 0)
 
-#define __types_ok(x, y) 			\
-	(__is_signed(x) == __is_signed(y) ||	\
-		__is_signed((x) + 0) == __is_signed((y) + 0))
+/* True for a non-negative signed int constant */
+#define __is_noneg_int(x)	\
+	(__builtin_choose_expr(__is_constexpr(x) && __is_signed(x), x, -1) >= 0)
+
+#define __types_ok(x, y) 					\
+	(__is_signed(x) == __is_signed(y) ||			\
+		__is_signed((x) + 0) == __is_signed((y) + 0) ||	\
+		__is_noneg_int(x) || __is_noneg_int(y))
 
 #define __cmp_op_min <
 #define __cmp_op_max >
author maintainer
#211 lore raw

PATCH 206/332 minmax: avoid overly complicated constant expressions in VM code

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Linus Torvalds <[email protected]>

[ Upstream commit 3a7e02c040b130b5545e4b115aada7bacd80a2b6 ]

The minmax infrastructure is overkill for simple constants, and can cause huge expansions because those simple constants are then used by other things.

For example, 'pageblock_order' is a core VM constant, but because it was implemented using 'min_t()' and all the type-checking that involves, it actually expanded to something like 2.5kB of preprocessor noise.

And when that simple constant was then used inside other expansions:

  #define pageblock_nr_pages      (1UL << pageblock_order)
  #define pageblock_start_pfn(pfn)  ALIGN_DOWN((pfn), pageblock_nr_pages)

and we then use that inside a 'max()' macro:

	case ISOLATE_SUCCESS:
		update_cached = false;
		last_migrated_pfn = max(cc->zone->zone_start_pfn,
			pageblock_start_pfn(cc->migrate_pfn - 1));

the end result was that one statement expanding to 253kB in size.

There are probably other cases of this, but this one case certainly stood out.

I've added 'MIN_T()' and 'MAX_T()' macros for this kind of "core simple constant with specific type" use. These macros skip the type checking, and as such need to be very sparingly used only for obvious cases that have active issues like this.

---
 include/linux/minmax.h |    7 +++++++
 1 file changed, 7 insertions(+)
include/linux/minmax.h +7 -0
@@ -270,4 +270,11 @@ static inline bool in_range32(u32 val, u
 #define swap(a, b) \
 	do { typeof(a) __tmp = (a); (a) = (b); (b) = __tmp; } while (0)
 
+/*
+ * Use these carefully: no type checking, and uses the arguments
+ * multiple times. Use for obvious constants only.
+ */
+#define MIN_T(type,a,b) __cmp(min,(type)(a),(type)(b))
+#define MAX_T(type,a,b) __cmp(max,(type)(a),(type)(b))
+
 #endif	/* _LINUX_MINMAX_H */
author maintainer
#212 lore raw

PATCH 207/332 minmax: add a few more MIN_T/MAX_T users

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Linus Torvalds <[email protected]>

[ Upstream commit 4477b39c32fdc03363affef4b11d48391e6dc9ff ]

Commit 3a7e02c040b1 ("minmax: avoid overly complicated constant expressions in VM code") added the simpler MIN_T/MAX_T macros in order to avoid some excessive expansion from the rather complicated regular min/max macros.

The complexity of those macros stems from two issues:

(a) trying to use them in situations that require a C constant expression (in static initializers and for array sizes)

(b) the type sanity checking

and MIN_T/MAX_T avoids both of these issues.

Now, in the whole (long) discussion about all this, it was pointed out that the whole type sanity checking is entirely unnecessary for min_t/max_t which get a fixed type that the comparison is done in.

But that still leaves min_t/max_t unnecessarily complicated due to worries about the C constant expression case.

However, it turns out that there really aren't very many cases that use min_t/max_t for this, and we can just force-convert those.

This does exactly that.

Which in turn will then allow for much simpler implementations of min_t()/max_t(). All the usual "macros in all upper case will evaluate the arguments multiple times" rules apply.

We should do all the same things for the regular min/max() vs MIN/MAX() cases, but that has the added complexity of various drivers defining their own local versions of MIN/MAX, so that needs another level of fixes first.

---
 arch/x86/mm/pgtable.c                             |    2 +-
 drivers/edac/sb_edac.c                            |    4 ++--
 drivers/gpu/drm/drm_color_mgmt.c                  |    2 +-
 drivers/md/dm-integrity.c                         |    2 +-
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c |    2 +-
 fs/erofs/zdata.h                                  |    2 +-
 net/ipv4/proc.c                                   |    2 +-
 net/ipv6/proc.c                                   |    2 +-
 8 files changed, 9 insertions(+), 9 deletions(-)
arch/x86/mm/pgtable.c +1 -1
@@ -107,7 +107,7 @@ static inline void pgd_list_del(pgd_t *p
 #define UNSHARED_PTRS_PER_PGD				\
 	(SHARED_KERNEL_PMD ? KERNEL_PGD_BOUNDARY : PTRS_PER_PGD)
 #define MAX_UNSHARED_PTRS_PER_PGD			\
-	max_t(size_t, KERNEL_PGD_BOUNDARY, PTRS_PER_PGD)
+	MAX_T(size_t, KERNEL_PGD_BOUNDARY, PTRS_PER_PGD)
 
 
 static void pgd_set_mm(pgd_t *pgd, struct mm_struct *mm)
drivers/edac/sb_edac.c +2 -2
@@ -109,8 +109,8 @@ static const u32 knl_interleave_list[] =
 	0x104, 0x10c, 0x114, 0x11c,   /* 20-23 */
 };
 #define MAX_INTERLEAVE							\
-	(max_t(unsigned int, ARRAY_SIZE(sbridge_interleave_list),	\
-	       max_t(unsigned int, ARRAY_SIZE(ibridge_interleave_list),	\
+	(MAX_T(unsigned int, ARRAY_SIZE(sbridge_interleave_list),	\
+	       MAX_T(unsigned int, ARRAY_SIZE(ibridge_interleave_list),	\
 		     ARRAY_SIZE(knl_interleave_list))))
 
 struct interleave_pkg {
drivers/gpu/drm/drm_color_mgmt.c +1 -1
@@ -421,7 +421,7 @@ int drm_plane_create_color_properties(st
 {
 	struct drm_device *dev = plane->dev;
 	struct drm_property *prop;
-	struct drm_prop_enum_list enum_list[max_t(int, DRM_COLOR_ENCODING_MAX,
+	struct drm_prop_enum_list enum_list[MAX_T(int, DRM_COLOR_ENCODING_MAX,
 						       DRM_COLOR_RANGE_MAX)];
 	int i, len;
 
drivers/md/dm-integrity.c +1 -1
@@ -2431,7 +2431,7 @@ static void do_journal_write(struct dm_i
 				    unlikely(from_replay) &&
 #endif
 				    ic->internal_hash) {
-					char test_tag[max_t(size_t, HASH_MAX_DIGESTSIZE, MAX_TAG_SIZE)];
+					char test_tag[MAX_T(size_t, HASH_MAX_DIGESTSIZE, MAX_TAG_SIZE)];
 
 					integrity_sector_checksum(ic, sec + ((l - j) << ic->sb->log2_sectors_per_block),
 								  (char *)access_journal_data(ic, i, l), test_tag);
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1 -1
@@ -2267,7 +2267,7 @@ static void stmmac_dma_interrupt(struct
 	u32 channels_to_check = tx_channel_count > rx_channel_count ?
 				tx_channel_count : rx_channel_count;
 	u32 chan;
-	int status[max_t(u32, MTL_MAX_TX_QUEUES, MTL_MAX_RX_QUEUES)];
+	int status[MAX_T(u32, MTL_MAX_TX_QUEUES, MTL_MAX_RX_QUEUES)];
 
 	/* Make sure we never check beyond our status buffer. */
 	if (WARN_ON_ONCE(channels_to_check > ARRAY_SIZE(status)))
fs/erofs/zdata.h +1 -1
@@ -182,7 +182,7 @@ static inline void z_erofs_onlinepage_en
 }
 
 #define Z_EROFS_VMAP_ONSTACK_PAGES	\
-	min_t(unsigned int, THREAD_SIZE / 8 / sizeof(struct page *), 96U)
+	MIN_T(unsigned int, THREAD_SIZE / 8 / sizeof(struct page *), 96U)
 #define Z_EROFS_VMAP_GLOBAL_PAGES	2048
 
 #endif
net/ipv4/proc.c +1 -1
@@ -43,7 +43,7 @@
 #include <net/sock.h>
 #include <net/raw.h>
 
-#define TCPUDP_MIB_MAX max_t(u32, UDP_MIB_MAX, TCP_MIB_MAX)
+#define TCPUDP_MIB_MAX MAX_T(u32, UDP_MIB_MAX, TCP_MIB_MAX)
 
 /*
  *	Report socket allocation statistics [[email protected]]
net/ipv6/proc.c +1 -1
@@ -27,7 +27,7 @@
 #include <net/ipv6.h>
 
 #define MAX4(a, b, c, d) \
-	max_t(u32, max_t(u32, a, b), max_t(u32, c, d))
+	MAX_T(u32, MAX_T(u32, a, b), MAX_T(u32, c, d))
 #define SNMP_MIB_MAX MAX4(UDP_MIB_MAX, TCP_MIB_MAX, \
 			IPSTATS_MIB_MAX, ICMP_MIB_MAX)
 
author maintainer
#213 lore raw

PATCH 208/332 minmax: simplify and clarify min_t()/max_t() implementation

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Linus Torvalds <[email protected]>

[ Upstream commit 017fa3e89187848fd056af757769c9e66ac3e93d ]

This simplifies the min_t() and max_t() macros by no longer making them work in the context of a C constant expression.

That means that you can no longer use them for static initializers or for array sizes in type definitions, but there were only a couple of such uses, and all of them were converted (famous last words) to use MIN_T/MAX_T instead.

---
 include/linux/minmax.h |   19 +++++++++++--------
 1 file changed, 11 insertions(+), 8 deletions(-)
include/linux/minmax.h +11 -8
@@ -45,17 +45,20 @@
 
 #define __cmp(op, x, y)	((x) __cmp_op_##op (y) ? (x) : (y))
 
-#define __cmp_once(op, x, y, unique_x, unique_y) ({	\
-	typeof(x) unique_x = (x);			\
-	typeof(y) unique_y = (y);			\
+#define __cmp_once_unique(op, type, x, y, ux, uy) \
+	({ type ux = (x); type uy = (y); __cmp(op, ux, uy); })
+
+#define __cmp_once(op, type, x, y) \
+	__cmp_once_unique(op, type, x, y, __UNIQUE_ID(x_), __UNIQUE_ID(y_))
+
+#define __careful_cmp_once(op, x, y) ({			\
 	static_assert(__types_ok(x, y),			\
 		#op "(" #x ", " #y ") signedness error, fix types or consider u" #op "() before " #op "_t()"); \
-	__cmp(op, unique_x, unique_y); })
+	__cmp_once(op, __auto_type, x, y); })
 
 #define __careful_cmp(op, x, y)					\
 	__builtin_choose_expr(__is_constexpr((x) - (y)),	\
-		__cmp(op, x, y),				\
-		__cmp_once(op, x, y, __UNIQUE_ID(__x), __UNIQUE_ID(__y)))
+		__cmp(op, x, y), __careful_cmp_once(op, x, y))
 
 #define __clamp(val, lo, hi)	\
 	((val) >= (hi) ? (hi) : ((val) <= (lo) ? (lo) : (val)))
@@ -158,7 +161,7 @@
  * @x: first value
  * @y: second value
  */
-#define min_t(type, x, y)	__careful_cmp(min, (type)(x), (type)(y))
+#define min_t(type, x, y) __cmp_once(min, type, x, y)
 
 /**
  * max_t - return maximum of two values, using the specified type
@@ -166,7 +169,7 @@
  * @x: first value
  * @y: second value
  */
-#define max_t(type, x, y)	__careful_cmp(max, (type)(x), (type)(y))
+#define max_t(type, x, y) __cmp_once(max, type, x, y)
 
 /*
  * Do not check the array parameter using __must_be_array().
author maintainer
#214 lore raw

PATCH 209/332 minmax: make generic MIN() and MAX() macros available everywhere

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Linus Torvalds <[email protected]>

[ Upstream commit 1a251f52cfdc417c84411a056bc142cbd77baef4 ]

This just standardizes the use of MIN() and MAX() macros, with the very traditional semantics. The goal is to use these for C constant expressions and for top-level / static initializers, and so be able to simplify the min()/max() macros.

These macro names were used by various kernel code - they are very traditional, after all - and all such users have been fixed up, with a few different approaches:

- trivial duplicated macro definitions have been removed

Note that 'trivial' here means that it's obviously kernel code that already included all the major kernel headers, and thus gets the new generic MIN/MAX macros automatically.

- non-trivial duplicated macro definitions are guarded with #ifndef

This is the "yes, they define their own versions, but no, the include situation is not entirely obvious, and maybe they don't get the generic version automatically" case.

- strange use case #1

A couple of drivers decided that the way they want to describe their versioning is with

	#define MAJ 1
	#define MIN 2
	#define DRV_VERSION __stringify(MAJ) "." __stringify(MIN)

which adds zero value and I just did my Alexander the Great impersonation, and rewrote that pointless Gordian knot as

	#define DRV_VERSION "1.2"

instead.

- strange use case #2

A couple of drivers thought that it's a good idea to have a random 'MIN' or 'MAX' define for a value or index into a table, rather than the traditional macro that takes arguments.

These values were re-written as C enum's instead. The new function-line macros only expand when followed by an open parenthesis, and thus don't clash with enum use.

Happily, there weren't really all that many of these cases, and a lot of users already had the pattern of using '#ifndef' guarding (or in one case just using '#undef MIN') before defining their own private version that does the same thing. I left such cases alone.

---
 arch/um/drivers/mconsole_user.c                                       |    2 
 drivers/edac/skx_common.h                                             |    1 
 drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c                   |    2 
 drivers/gpu/drm/amd/pm/powerplay/hwmgr/ppevvmath.h                    |   14 ++++-
 drivers/gpu/drm/radeon/evergreen_cs.c                                 |    2 
 drivers/hwmon/adt7475.c                                               |   24 +++++-----
 drivers/media/dvb-frontends/stv0367_priv.h                            |    3 +
 drivers/net/fjes/fjes_main.c                                          |    4 -
 drivers/nfc/pn544/i2c.c                                               |    2 
 drivers/platform/x86/sony-laptop.c                                    |    1 
 drivers/scsi/isci/init.c                                              |    6 --
 drivers/staging/media/atomisp/pci/hive_isp_css_include/math_support.h |    5 --
 include/linux/minmax.h                                                |    2 
 kernel/trace/preemptirq_delay_test.c                                  |    2 
 lib/btree.c                                                           |    1 
 lib/decompress_unlzma.c                                               |    2 
 lib/zstd/zstd_internal.h                                              |    2 
 mm/zsmalloc.c                                                         |    1 
 18 files changed, 37 insertions(+), 39 deletions(-)
arch/um/drivers/mconsole_user.c +2 -0
@@ -71,7 +71,9 @@ static struct mconsole_command *mconsole
 	return NULL;
 }
 
+#ifndef MIN
 #define MIN(a,b) ((a)<(b) ? (a):(b))
+#endif
 
 #define STRINGX(x) #x
 #define STRING(x) STRINGX(x)
drivers/edac/skx_common.h +0 -1
@@ -36,7 +36,6 @@
 #define I10NM_NUM_CHANNELS	2
 #define I10NM_NUM_DIMMS		2
 
-#define MAX(a, b)	((a) > (b) ? (a) : (b))
 #define NUM_IMC		MAX(SKX_NUM_IMC, I10NM_NUM_IMC)
 #define NUM_CHANNELS	MAX(SKX_NUM_CHANNELS, I10NM_NUM_CHANNELS)
 #define NUM_DIMMS	MAX(SKX_NUM_DIMMS, I10NM_NUM_DIMMS)
drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c +2 -0
@@ -25,7 +25,9 @@
 
 #include "hdcp.h"
 
+#ifndef MIN
 #define MIN(a, b) ((a) < (b) ? (a) : (b))
+#endif
 #define HDCP_I2C_ADDR 0x3a	/* 0x74 >> 1*/
 #define KSV_READ_SIZE 0xf	/* 0x6803b - 0x6802c */
 #define HDCP_MAX_AUX_TRANSACTION_SIZE 16
drivers/gpu/drm/amd/pm/powerplay/hwmgr/ppevvmath.h +10 -4
@@ -22,12 +22,18 @@
  */
 #include <asm/div64.h>
 
-#define SHIFT_AMOUNT 16 /* We multiply all original integers with 2^SHIFT_AMOUNT to get the fInt representation */
+enum ppevvmath_constants {
+	/* We multiply all original integers with 2^SHIFT_AMOUNT to get the fInt representation */
+	SHIFT_AMOUNT	= 16,
 
-#define PRECISION 5 /* Change this value to change the number of decimal places in the final output - 5 is a good default */
+	/* Change this value to change the number of decimal places in the final output - 5 is a good default */
+	PRECISION	=  5,
 
-#define SHIFTED_2 (2 << SHIFT_AMOUNT)
-#define MAX (1 << (SHIFT_AMOUNT - 1)) - 1 /* 32767 - Might change in the future */
+	SHIFTED_2	= (2 << SHIFT_AMOUNT),
+
+	/* 32767 - Might change in the future */
+	MAX		= (1 << (SHIFT_AMOUNT - 1)) - 1,
+};
 
 /* -------------------------------------------------------------------------------
  * NEW TYPE - fINT
drivers/gpu/drm/radeon/evergreen_cs.c +2 -0
@@ -32,8 +32,10 @@
 #include "evergreen_reg_safe.h"
 #include "cayman_reg_safe.h"
 
+#ifndef MIN
 #define MAX(a,b)                   (((a)>(b))?(a):(b))
 #define MIN(a,b)                   (((a)<(b))?(a):(b))
+#endif
 
 #define REG_SAFE_BM_SIZE ARRAY_SIZE(evergreen_reg_safe_bm)
 
drivers/hwmon/adt7475.c +12 -12
@@ -23,23 +23,23 @@
 #include <linux/util_macros.h>
 
 /* Indexes for the sysfs hooks */
-
-#define INPUT		0
-#define MIN		1
-#define MAX		2
-#define CONTROL		3
-#define OFFSET		3
-#define AUTOMIN		4
-#define THERM		5
-#define HYSTERSIS	6
-
+enum adt_sysfs_id {
+	INPUT		= 0,
+	MIN		= 1,
+	MAX		= 2,
+	CONTROL		= 3,
+	OFFSET		= 3,	// Dup
+	AUTOMIN		= 4,
+	THERM		= 5,
+	HYSTERSIS	= 6,
 /*
  * These are unique identifiers for the sysfs functions - unlike the
  * numbers above, these are not also indexes into an array
  */
+	ALARM		= 9,
+	FAULT		= 10,
+};
 
-#define ALARM		9
-#define FAULT		10
 
 /* 7475 Common Registers */
 
drivers/media/dvb-frontends/stv0367_priv.h +3 -0
@@ -25,8 +25,11 @@
 #endif
 
 /* MACRO definitions */
+#ifndef MIN
 #define MAX(X, Y) ((X) >= (Y) ? (X) : (Y))
 #define MIN(X, Y) ((X) <= (Y) ? (X) : (Y))
+#endif
+
 #define INRANGE(X, Y, Z) \
 	((((X) <= (Y)) && ((Y) <= (Z))) || \
 	(((Z) <= (Y)) && ((Y) <= (X))) ? 1 : 0)
drivers/net/fjes/fjes_main.c +1 -3
@@ -14,9 +14,7 @@
 #include "fjes.h"
 #include "fjes_trace.h"
 
-#define MAJ 1
-#define MIN 2
-#define DRV_VERSION __stringify(MAJ) "." __stringify(MIN)
+#define DRV_VERSION "1.2"
 #define DRV_NAME	"fjes"
 char fjes_driver_name[] = DRV_NAME;
 char fjes_driver_version[] = DRV_VERSION;
drivers/nfc/pn544/i2c.c +0 -2
@@ -126,8 +126,6 @@ struct pn544_i2c_fw_secure_blob {
 #define PN544_FW_CMD_RESULT_COMMAND_REJECTED 0xE0
 #define PN544_FW_CMD_RESULT_CHUNK_ERROR 0xE6
 
-#define MIN(X, Y) ((X) < (Y) ? (X) : (Y))
-
 #define PN544_FW_WRITE_BUFFER_MAX_LEN 0x9f7
 #define PN544_FW_I2C_MAX_PAYLOAD PN544_HCI_I2C_LLC_MAX_SIZE
 #define PN544_FW_I2C_WRITE_FRAME_HEADER_LEN 8
drivers/platform/x86/sony-laptop.c +0 -1
@@ -757,7 +757,6 @@ static union acpi_object *__call_snc_met
 	return result;
 }
 
-#define MIN(a, b)	(a > b ? b : a)
 static int sony_nc_buffer_call(acpi_handle handle, char *name, u64 *value,
 		void *buffer, size_t buflen)
 {
drivers/scsi/isci/init.c +1 -5
@@ -65,11 +65,7 @@
 #include "task.h"
 #include "probe_roms.h"
 
-#define MAJ 1
-#define MIN 2
-#define BUILD 0
-#define DRV_VERSION __stringify(MAJ) "." __stringify(MIN) "." \
-	__stringify(BUILD)
+#define DRV_VERSION "1.2.0"
 
 MODULE_VERSION(DRV_VERSION);
 
drivers/staging/media/atomisp/pci/hive_isp_css_include/math_support.h +0 -5
@@ -31,11 +31,6 @@
 /* A => B */
 #define IMPLIES(a, b)        (!(a) || (b))
 
-/* for preprocessor and array sizing use MIN and MAX
-   otherwise use min and max */
-#define MAX(a, b)            (((a) > (b)) ? (a) : (b))
-#define MIN(a, b)            (((a) < (b)) ? (a) : (b))
-
 #define ROUND_DIV(a, b)      (((b) != 0) ? ((a) + ((b) >> 1)) / (b) : 0)
 #define CEIL_DIV(a, b)       (((b) != 0) ? ((a) + (b) - 1) / (b) : 0)
 #define CEIL_MUL(a, b)       (CEIL_DIV(a, b) * (b))
include/linux/minmax.h +2 -0
@@ -277,6 +277,8 @@ static inline bool in_range32(u32 val, u
  * Use these carefully: no type checking, and uses the arguments
  * multiple times. Use for obvious constants only.
  */
+#define MIN(a,b) __cmp(min,a,b)
+#define MAX(a,b) __cmp(max,a,b)
 #define MIN_T(type,a,b) __cmp(min,(type)(a),(type)(b))
 #define MAX_T(type,a,b) __cmp(max,(type)(a),(type)(b))
 
kernel/trace/preemptirq_delay_test.c +0 -2
@@ -31,8 +31,6 @@ MODULE_PARM_DESC(burst_size, "The size o
 
 static struct completion done;
 
-#define MIN(x, y) ((x) < (y) ? (x) : (y))
-
 static void busy_wait(ulong time)
 {
 	u64 start, end;
lib/btree.c +0 -1
@@ -43,7 +43,6 @@
 #include <linux/slab.h>
 #include <linux/module.h>
 
-#define MAX(a, b) ((a) > (b) ? (a) : (b))
 #define NODESIZE MAX(L1_CACHE_BYTES, 128)
 
 struct btree_geo {
lib/decompress_unlzma.c +2 -0
@@ -37,7 +37,9 @@
 
 #include <linux/decompress/mm.h>
 
+#ifndef MIN
 #define	MIN(a, b) (((a) < (b)) ? (a) : (b))
+#endif
 
 static long long INIT read_int(unsigned char *ptr, int size)
 {
lib/zstd/zstd_internal.h +0 -2
@@ -36,8 +36,6 @@
 /*-*************************************
 *  shared macros
 ***************************************/
-#define MIN(a, b) ((a) < (b) ? (a) : (b))
-#define MAX(a, b) ((a) > (b) ? (a) : (b))
 #define CHECK_F(f)                       \
 	{                                \
 		size_t const errcod = f; \
mm/zsmalloc.c +0 -1
@@ -126,7 +126,6 @@
 #define ISOLATED_BITS	3
 #define MAGIC_VAL_BITS	8
 
-#define MAX(a, b) ((a) >= (b) ? (a) : (b))
 /* ZS_MIN_ALLOC_SIZE must be multiple of ZS_ALIGN */
 #define ZS_MIN_ALLOC_SIZE \
 	MAX(32, (ZS_MAX_PAGES_PER_ZSPAGE << PAGE_SHIFT >> OBJ_INDEX_BITS))
author maintainer
#215 lore raw

PATCH 210/332 minmax: dont use max() in situations that want a C constant expression

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Linus Torvalds <[email protected]>

[ Upstream commit cb04e8b1d2f24c4c2c92f7b7529031fc35a16fed ]

We only had a couple of array[] declarations, and changing them to just use 'MAX()' instead of 'max()' fixes the issue.

This will allow us to simplify our min/max macros enormously, since they can now unconditionally use temporary variables to avoid using the argument values multiple times.

---
 drivers/input/touchscreen/cyttsp4_core.c |    2 +-
 drivers/md/dm-integrity.c                |    4 ++--
 fs/btrfs/tree-checker.c                  |    2 +-
 lib/vsprintf.c                           |    2 +-
 4 files changed, 5 insertions(+), 5 deletions(-)
drivers/input/touchscreen/cyttsp4_core.c +1 -1
@@ -857,7 +857,7 @@ static void cyttsp4_get_mt_touches(struc
 	struct cyttsp4_touch tch;
 	int sig;
 	int i, j, t = 0;
-	int ids[max(CY_TMA1036_MAX_TCH, CY_TMA4XX_MAX_TCH)];
+	int ids[MAX(CY_TMA1036_MAX_TCH, CY_TMA4XX_MAX_TCH)];
 
 	memset(ids, 0, si->si_ofs.tch_abs[CY_TCH_T].max * sizeof(int));
 	for (i = 0; i < num_cur_tch; i++) {
drivers/md/dm-integrity.c +2 -2
@@ -1600,7 +1600,7 @@ static void integrity_metadata(struct wo
 		struct bio *bio = dm_bio_from_per_bio_data(dio, sizeof(struct dm_integrity_io));
 		char *checksums;
 		unsigned extra_space = unlikely(digest_size > ic->tag_size) ? digest_size - ic->tag_size : 0;
-		char checksums_onstack[max((size_t)HASH_MAX_DIGESTSIZE, MAX_TAG_SIZE)];
+		char checksums_onstack[MAX(HASH_MAX_DIGESTSIZE, MAX_TAG_SIZE)];
 		sector_t sector;
 		unsigned sectors_to_process;
 
@@ -1882,7 +1882,7 @@ retry_kmap:
 				} while (++s < ic->sectors_per_block);
 #ifdef INTERNAL_VERIFY
 				if (ic->internal_hash) {
-					char checksums_onstack[max((size_t)HASH_MAX_DIGESTSIZE, MAX_TAG_SIZE)];
+					char checksums_onstack[MAX(HASH_MAX_DIGESTSIZE, MAX_TAG_SIZE)];
 
 					integrity_sector_checksum(ic, logical_sector, mem + bv.bv_offset, checksums_onstack);
 					if (unlikely(memcmp(checksums_onstack, journal_entry_tag(ic, je), ic->tag_size))) {
fs/btrfs/tree-checker.c +1 -1
@@ -587,7 +587,7 @@ static int check_dir_item(struct extent_
 		 */
 		if (key->type == BTRFS_DIR_ITEM_KEY ||
 		    key->type == BTRFS_XATTR_ITEM_KEY) {
-			char namebuf[max(BTRFS_NAME_LEN, XATTR_NAME_MAX)];
+			char namebuf[MAX(BTRFS_NAME_LEN, XATTR_NAME_MAX)];
 
 			read_extent_buffer(leaf, namebuf,
 					(unsigned long)(di + 1), name_len);
lib/vsprintf.c +1 -1
@@ -1078,7 +1078,7 @@ char *resource_string(char *buf, char *e
 #define FLAG_BUF_SIZE		(2 * sizeof(res->flags))
 #define DECODED_BUF_SIZE	sizeof("[mem - 64bit pref window disabled]")
 #define RAW_BUF_SIZE		sizeof("[mem - flags 0x]")
-	char sym[max(2*RSRC_BUF_SIZE + DECODED_BUF_SIZE,
+	char sym[MAX(2*RSRC_BUF_SIZE + DECODED_BUF_SIZE,
 		     2*RSRC_BUF_SIZE + FLAG_BUF_SIZE + RAW_BUF_SIZE)];
 
 	char *p = sym, *pend = sym + sizeof(sym);
author maintainer
#216 lore raw

PATCH 211/332 minmax: simplify min()/max()/clamp() implementation

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Linus Torvalds <[email protected]>

[ Upstream commit dc1c8034e31b14a2e5e212104ec508aec44ce1b9 ]

Now that we no longer have any C constant expression contexts (ie array size declarations or static initializers) that use min() or max(), we can simpify the implementation by not having to worry about the result staying as a C constant expression.

So now we can unconditionally just use temporary variables of the right type, and get rid of the excessive expansion that used to come from the use of

__builtin_choose_expr(__is_constexpr(...), ..

to pick the specialized code for constant expressions.

Another expansion simplification is to pass the temporary variables (in addition to the original expression) to our __types_ok() macro. That may superficially look like it complicates the macro, but when we only want the type of the expression, expanding the temporary variable names is much simpler and smaller than expanding the potentially complicated original expression.

As a result, on my machine, doing a

  $ time make drivers/staging/media/atomisp/pci/isp/kernels/ynr/ynr_1.0/ia_css_ynr.host.i

goes from

	real	0m16.621s
	user	0m15.360s
	sys	0m1.221s

to

	real	0m2.532s
	user	0m2.091s
	sys	0m0.452s

because the token expansion goes down dramatically.

In particular, the longest line expansion (which was line 71 of that 'ia_css_ynr.host.c' file) shrinks from 23,338kB (yes, 23MB for one single line) to "just" 1,444kB (now "only" 1.4MB).

And yes, that line is still the line from hell, because it's doing multiple levels of "min()/max()" expansion thanks to some of them being hidden inside the uDIGIT_FITTING() macro.

Lorenzo has a nice cleanup patch that makes that driver use inline functions instead of macros for sDIGIT_FITTING() and uDIGIT_FITTING(), which will fix that line once and for all, but the 16-fold reduction in this case does show why we need to simplify these helpers.

---
 include/linux/minmax.h |   43 ++++++++++++++++++++-----------------------
 1 file changed, 20 insertions(+), 23 deletions(-)
include/linux/minmax.h +20 -23
@@ -35,10 +35,10 @@
 #define __is_noneg_int(x)	\
 	(__builtin_choose_expr(__is_constexpr(x) && __is_signed(x), x, -1) >= 0)
 
-#define __types_ok(x, y) 					\
-	(__is_signed(x) == __is_signed(y) ||			\
-		__is_signed((x) + 0) == __is_signed((y) + 0) ||	\
-		__is_noneg_int(x) || __is_noneg_int(y))
+#define __types_ok(x, y, ux, uy) 				\
+	(__is_signed(ux) == __is_signed(uy) ||			\
+	 __is_signed((ux) + 0) == __is_signed((uy) + 0) ||	\
+	 __is_noneg_int(x) || __is_noneg_int(y))
 
 #define __cmp_op_min <
 #define __cmp_op_max >
@@ -51,34 +51,31 @@
 #define __cmp_once(op, type, x, y) \
 	__cmp_once_unique(op, type, x, y, __UNIQUE_ID(x_), __UNIQUE_ID(y_))
 
-#define __careful_cmp_once(op, x, y) ({			\
-	static_assert(__types_ok(x, y),			\
+#define __careful_cmp_once(op, x, y, ux, uy) ({		\
+	__auto_type ux = (x); __auto_type uy = (y);	\
+	static_assert(__types_ok(x, y, ux, uy),		\
 		#op "(" #x ", " #y ") signedness error, fix types or consider u" #op "() before " #op "_t()"); \
-	__cmp_once(op, __auto_type, x, y); })
+	__cmp(op, ux, uy); })
 
-#define __careful_cmp(op, x, y)					\
-	__builtin_choose_expr(__is_constexpr((x) - (y)),	\
-		__cmp(op, x, y), __careful_cmp_once(op, x, y))
+#define __careful_cmp(op, x, y) \
+	__careful_cmp_once(op, x, y, __UNIQUE_ID(x_), __UNIQUE_ID(y_))
 
 #define __clamp(val, lo, hi)	\
 	((val) >= (hi) ? (hi) : ((val) <= (lo) ? (lo) : (val)))
 
-#define __clamp_once(val, lo, hi, unique_val, unique_lo, unique_hi) ({		\
-	typeof(val) unique_val = (val);						\
-	typeof(lo) unique_lo = (lo);						\
-	typeof(hi) unique_hi = (hi);						\
+#define __clamp_once(val, lo, hi, uval, ulo, uhi) ({				\
+	__auto_type uval = (val);						\
+	__auto_type ulo = (lo);							\
+	__auto_type uhi = (hi);							\
 	static_assert(__builtin_choose_expr(__is_constexpr((lo) > (hi)), 	\
 			(lo) <= (hi), true),					\
 		"clamp() low limit " #lo " greater than high limit " #hi);	\
-	static_assert(__types_ok(val, lo), "clamp() 'lo' signedness error");	\
-	static_assert(__types_ok(val, hi), "clamp() 'hi' signedness error");	\
-	__clamp(unique_val, unique_lo, unique_hi); })
-
-#define __careful_clamp(val, lo, hi) ({					\
-	__builtin_choose_expr(__is_constexpr((val) - (lo) + (hi)),	\
-		__clamp(val, lo, hi),					\
-		__clamp_once(val, lo, hi, __UNIQUE_ID(__val),		\
-			     __UNIQUE_ID(__lo), __UNIQUE_ID(__hi))); })
+	static_assert(__types_ok(uval, lo, uval, ulo), "clamp() 'lo' signedness error");	\
+	static_assert(__types_ok(uval, hi, uval, uhi), "clamp() 'hi' signedness error");	\
+	__clamp(uval, ulo, uhi); })
+
+#define __careful_clamp(val, lo, hi) \
+	__clamp_once(val, lo, hi, __UNIQUE_ID(v_), __UNIQUE_ID(l_), __UNIQUE_ID(h_))
 
 /**
  * min - return minimum of two values of the same or compatible types
author maintainer
#217 lore raw

PATCH 212/332 minmax: improve macro expansion and type checking

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Linus Torvalds <[email protected]>

[ Upstream commit 22f5468731491e53356ba7c028f0fdea20b18e2c ]

This clarifies the rules for min()/max()/clamp() type checking and makes them a much more efficient macro expansion.

In particular, we now look at the type and range of the inputs to see whether they work together, generating a mask of acceptable comparisons, and then just verifying that the inputs have a shared case:

- an expression with a signed type can be used for
(1) signed comparisons
(2) unsigned comparisons if it is statically known to have a non-negative value

- an expression with an unsigned type can be used for
(3) unsigned comparison
(4) signed comparisons if the type is smaller than 'int' and thus the C integer promotion rules will make it signed anyway

Here rule (1) and (3) are obvious, and rule (2) is important in order to allow obvious trivial constants to be used together with unsigned values.

Rule (4) is not necessarily a good idea, but matches what we used to do, and we have extant cases of this situation in the kernel. Notably with bcachefs having an expression like

	min(bch2_bucket_sectors_dirty(a), ca->mi.bucket_size)

where bch2_bucket_sectors_dirty() returns an 's64', and 'ca->mi.bucket_size' is of type 'u16'.

Technically that bcachefs comparison is clearly sensible on a C type level, because the 'u16' will go through the normal C integer promotion, and become 'int', and then we're comparing two signed values and everything looks sane.

However, it's not entirely clear that a 'min(s64,u16)' operation makes a lot of conceptual sense, and it's possible that we will remove rule (4). After all, the _reason_ we have these complicated type checks is exactly that the C type promotion rules are not very intuitive.

But at least for now the rule is in place for backwards compatibility.

Also note that rule (2) existed before, but is hugely relaxed by this commit. It used to be true only for the simplest compile-time non-negative integer constants. The new macro model will allow cases where the compiler can trivially see that an expression is non-negative even if it isn't necessarily a constant.

For example, the amdgpu driver does

	min_t(size_t, sizeof(fru_info->serial), pia[addr] & 0x3F));

because our old 'min()' macro would see that 'pia[addr] & 0x3F' is of type 'int' and clearly not a C constant expression, so doing a 'min()' with a 'size_t' is a signedness violation.

Our new 'min()' macro still sees that 'pia[addr] & 0x3F' is of type 'int', but is smart enough to also see that it is clearly non-negative, and thus would allow that case without any complaints.

---
 include/linux/compiler.h |    9 +++++
 include/linux/minmax.h   |   78 ++++++++++++++++++++++++++++++++++++-----------
 2 files changed, 70 insertions(+), 17 deletions(-)
include/linux/compiler.h +9 -0
@@ -252,6 +252,15 @@ static inline void *offset_to_ptr(const
 #define is_signed_type(type) (((type)(-1)) < (__force type)1)
 
 /*
+ * Useful shorthand for "is this condition known at compile-time?"
+ *
+ * Note that the condition may involve non-constant values,
+ * but the compiler may know enough about the details of the
+ * values to determine that the condition is statically true.
+ */
+#define statically_true(x) (__builtin_constant_p(x) && (x))
+
+/*
  * This is needed in functions which generate the stack canary, see
  * arch/x86/kernel/smpboot.c::start_secondary() for an example.
  */
include/linux/minmax.h +61 -17

96 lines not on this page · raw message

author maintainer
#218 lore raw

PATCH 213/332 minmax: fix up min3() and max3() too

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Linus Torvalds <[email protected]>

[ Upstream commit 21b136cc63d2a9ddd60d4699552b69c214b32964 ]

David Laight pointed out that we should deal with the min3() and max3() mess too, which still does excessive expansion.

And our current macros are actually rather broken.

In particular, the macros did this:

  #define min3(x, y, z) min((typeof(x))min(x, y), z)
  #define max3(x, y, z) max((typeof(x))max(x, y), z)

and that not only is a nested expansion of possibly very complex arguments with all that involves, the typing with that "typeof()" cast is completely wrong.

For example, imagine what happens in max3() if 'x' happens to be a 'unsigned char', but 'y' and 'z' are 'unsigned long'. The types are compatible, and there's no warning - but the result is just random garbage.

No, I don't think we've ever hit that issue in practice, but since we now have sane infrastructure for doing this right, let's just use it. It fixes any excessive expansion, and also avoids these kinds of broken type issues.

---
 include/linux/minmax.h |   12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)
include/linux/minmax.h +10 -2
@@ -152,13 +152,20 @@
 #define umax(x, y)	\
 	__careful_cmp(max, (x) + 0u + 0ul + 0ull, (y) + 0u + 0ul + 0ull)
 
+#define __careful_op3(op, x, y, z, ux, uy, uz) ({			\
+	__auto_type ux = (x); __auto_type uy = (y);__auto_type uz = (z);\
+	BUILD_BUG_ON_MSG(!__types_ok3(x,y,z,ux,uy,uz),			\
+		#op"3("#x", "#y", "#z") signedness error");		\
+	__cmp(op, ux, __cmp(op, uy, uz)); })
+
 /**
  * min3 - return minimum of three values
  * @x: first value
  * @y: second value
  * @z: third value
  */
-#define min3(x, y, z) min((typeof(x))min(x, y), z)
+#define min3(x, y, z) \
+	__careful_op3(min, x, y, z, __UNIQUE_ID(x_), __UNIQUE_ID(y_), __UNIQUE_ID(z_))
 
 /**
  * max3 - return maximum of three values
@@ -166,7 +173,8 @@
  * @y: second value
  * @z: third value
  */
-#define max3(x, y, z) max((typeof(x))max(x, y), z)
+#define max3(x, y, z) \
+	__careful_op3(max, x, y, z, __UNIQUE_ID(x_), __UNIQUE_ID(y_), __UNIQUE_ID(z_))
 
 /**
  * min_not_zero - return the minimum that is _not_ zero, unless both are zero
author maintainer
#219 lore raw

PATCH 214/332 minmax.h: add whitespace around operators and after commas

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Laight <[email protected]>

[ Upstream commit 71ee9b16251ea4bf7c1fe222517c82bdb3220acc ]

Patch series "minmax.h: Cleanups and minor optimisations".

Some tidyups and minor changes to minmax.h.

This patch (of 7):

---
 include/linux/minmax.h |   34 +++++++++++++++++-----------------
 1 file changed, 17 insertions(+), 17 deletions(-)
include/linux/minmax.h +17 -17
@@ -51,10 +51,10 @@
  * only need to be careful to not cause warnings for
  * pointer use.
  */
-#define __signed_type_use(x,ux) (2+__is_nonneg(x,ux))
-#define __unsigned_type_use(x,ux) (1+2*(sizeof(ux)<4))
-#define __sign_use(x,ux) (is_signed_type(typeof(ux))? \
-	__signed_type_use(x,ux):__unsigned_type_use(x,ux))
+#define __signed_type_use(x, ux) (2 + __is_nonneg(x, ux))
+#define __unsigned_type_use(x, ux) (1 + 2 * (sizeof(ux) < 4))
+#define __sign_use(x, ux) (is_signed_type(typeof(ux)) ? \
+	__signed_type_use(x, ux) : __unsigned_type_use(x, ux))
 
 /*
  * To avoid warnings about casting pointers to integers
@@ -74,15 +74,15 @@
 #ifdef CONFIG_64BIT
   #define __signed_type(ux) long
 #else
-  #define __signed_type(ux) typeof(__builtin_choose_expr(sizeof(ux)>4,1LL,1L))
+  #define __signed_type(ux) typeof(__builtin_choose_expr(sizeof(ux) > 4, 1LL, 1L))
 #endif
-#define __is_nonneg(x,ux) statically_true((__signed_type(ux))(x)>=0)
+#define __is_nonneg(x, ux) statically_true((__signed_type(ux))(x) >= 0)
 
-#define __types_ok(x,y,ux,uy) \
-	(__sign_use(x,ux) & __sign_use(y,uy))
+#define __types_ok(x, y, ux, uy) \
+	(__sign_use(x, ux) & __sign_use(y, uy))
 
-#define __types_ok3(x,y,z,ux,uy,uz) \
-	(__sign_use(x,ux) & __sign_use(y,uy) & __sign_use(z,uz))
+#define __types_ok3(x, y, z, ux, uy, uz) \
+	(__sign_use(x, ux) & __sign_use(y, uy) & __sign_use(z, uz))
 
 #define __cmp_op_min <
 #define __cmp_op_max >
@@ -97,7 +97,7 @@
 
 #define __careful_cmp_once(op, x, y, ux, uy) ({		\
 	__auto_type ux = (x); __auto_type uy = (y);	\
-	BUILD_BUG_ON_MSG(!__types_ok(x,y,ux,uy),	\
+	BUILD_BUG_ON_MSG(!__types_ok(x, y, ux, uy),	\
 		#op"("#x", "#y") signedness error");	\
 	__cmp(op, ux, uy); })
 
@@ -114,7 +114,7 @@
 	static_assert(__builtin_choose_expr(__is_constexpr((lo) > (hi)), 	\
 			(lo) <= (hi), true),					\
 		"clamp() low limit " #lo " greater than high limit " #hi);	\
-	BUILD_BUG_ON_MSG(!__types_ok3(val,lo,hi,uval,ulo,uhi),			\
+	BUILD_BUG_ON_MSG(!__types_ok3(val, lo, hi, uval, ulo, uhi),		\
 		"clamp("#val", "#lo", "#hi") signedness error");		\
 	__clamp(uval, ulo, uhi); })
 
@@ -154,7 +154,7 @@
 
 #define __careful_op3(op, x, y, z, ux, uy, uz) ({			\
 	__auto_type ux = (x); __auto_type uy = (y);__auto_type uz = (z);\
-	BUILD_BUG_ON_MSG(!__types_ok3(x,y,z,ux,uy,uz),			\
+	BUILD_BUG_ON_MSG(!__types_ok3(x, y, z, ux, uy, uz),		\
 		#op"3("#x", "#y", "#z") signedness error");		\
 	__cmp(op, ux, __cmp(op, uy, uz)); })
 
@@ -326,9 +326,9 @@ static inline bool in_range32(u32 val, u
  * Use these carefully: no type checking, and uses the arguments
  * multiple times. Use for obvious constants only.
  */
-#define MIN(a,b) __cmp(min,a,b)
-#define MAX(a,b) __cmp(max,a,b)
-#define MIN_T(type,a,b) __cmp(min,(type)(a),(type)(b))
-#define MAX_T(type,a,b) __cmp(max,(type)(a),(type)(b))
+#define MIN(a, b) __cmp(min, a, b)
+#define MAX(a, b) __cmp(max, a, b)
+#define MIN_T(type, a, b) __cmp(min, (type)(a), (type)(b))
+#define MAX_T(type, a, b) __cmp(max, (type)(a), (type)(b))
 
 #endif	/* _LINUX_MINMAX_H */
author maintainer
#220 lore raw

PATCH 215/332 minmax.h: update some comments

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Laight <[email protected]>

[ Upstream commit 10666e99204818ef45c702469488353b5bb09ec7 ]

- Change three to several.
- Remove the comment about retaining constant expressions, no longer true.
- Realign to nearer 80 columns and break on major punctiation.
- Add a leading comment to the block before __signed_type() and __is_nonneg() Otherwise the block explaining the cast is a bit 'floating'. Reword the rest of that comment to improve readability.

Cc Andy Shevchenko <[email protected]>
Cc Arnd Bergmann <[email protected]>
Cc Christoph Hellwig <[email protected]>
Cc Dan Carpenter <[email protected]>
Cc Jason A. Donenfeld <[email protected]>
Cc Jens Axboe <[email protected]>
Cc Lorenzo Stoakes <[email protected]>
Cc Mateusz Guzik <[email protected]>
Cc Matthew Wilcox <[email protected]>
Cc Pedro Falcato <[email protected]>
---
 include/linux/minmax.h |   61 ++++++++++++++++++++++---------------------------
 1 file changed, 28 insertions(+), 33 deletions(-)
include/linux/minmax.h +28 -33
@@ -8,13 +8,10 @@
 #include <linux/types.h>
 
 /*
- * min()/max()/clamp() macros must accomplish three things:
+ * min()/max()/clamp() macros must accomplish several things:
  *
  * - Avoid multiple evaluations of the arguments (so side-effects like
  *   "x++" happen only once) when non-constant.
- * - Retain result as a constant expressions when called with only
- *   constant expressions (to avoid tripping VLA warnings in stack
- *   allocation usage).
  * - Perform signed v unsigned type-checking (to generate compile
  *   errors instead of nasty runtime surprises).
  * - Unsigned char/short are always promoted to signed int and can be
@@ -31,25 +28,23 @@
  *   bit #0 set if ok for unsigned comparisons
  *   bit #1 set if ok for signed comparisons
  *
- * In particular, statically non-negative signed integer
- * expressions are ok for both.
+ * In particular, statically non-negative signed integer expressions
+ * are ok for both.
  *
- * NOTE! Unsigned types smaller than 'int' are implicitly
- * converted to 'int' in expressions, and are accepted for
- * signed conversions for now. This is debatable.
- *
- * Note that 'x' is the original expression, and 'ux' is
- * the unique variable that contains the value.
- *
- * We use 'ux' for pure type checking, and 'x' for when
- * we need to look at the value (but without evaluating
- * it for side effects! Careful to only ever evaluate it
- * with sizeof() or __builtin_constant_p() etc).
- *
- * Pointers end up being checked by the normal C type
- * rules at the actual comparison, and these expressions
- * only need to be careful to not cause warnings for
- * pointer use.
+ * NOTE! Unsigned types smaller than 'int' are implicitly converted to 'int'
+ * in expressions, and are accepted for signed conversions for now.
+ * This is debatable.
+ *
+ * Note that 'x' is the original expression, and 'ux' is the unique variable
+ * that contains the value.
+ *
+ * We use 'ux' for pure type checking, and 'x' for when we need to look at the
+ * value (but without evaluating it for side effects!
+ * Careful to only ever evaluate it with sizeof() or __builtin_constant_p() etc).
+ *
+ * Pointers end up being checked by the normal C type rules at the actual
+ * comparison, and these expressions only need to be careful to not cause
+ * warnings for pointer use.
  */
 #define __signed_type_use(x, ux) (2 + __is_nonneg(x, ux))
 #define __unsigned_type_use(x, ux) (1 + 2 * (sizeof(ux) < 4))
@@ -57,19 +52,19 @@
 	__signed_type_use(x, ux) : __unsigned_type_use(x, ux))
 
 /*
- * To avoid warnings about casting pointers to integers
- * of different sizes, we need that special sign type.
+ * Check whether a signed value is always non-negative.
  *
- * On 64-bit we can just always use 'long', since any
- * integer or pointer type can just be cast to that.
+ * A cast is needed to avoid any warnings from values that aren't signed
+ * integer types (in which case the result doesn't matter).
  *
- * This does not work for 128-bit signed integers since
- * the cast would truncate them, but we do not use s128
- * types in the kernel (we do use 'u128', but they will
- * be handled by the !is_signed_type() case).
- *
- * NOTE! The cast is there only to avoid any warnings
- * from when values that aren't signed integer types.
+ * On 64-bit any integer or pointer type can safely be cast to 'long'.
+ * But on 32-bit we need to avoid warnings about casting pointers to integers
+ * of different sizes without truncating 64-bit values so 'long' or 'long long'
+ * must be used depending on the size of the value.
+ *
+ * This does not work for 128-bit signed integers since the cast would truncate
+ * them, but we do not use s128 types in the kernel (we do use 'u128',
+ * but they are handled by the !is_signed_type() case).
  */
 #ifdef CONFIG_64BIT
   #define __signed_type(ux) long
author maintainer
#221 lore raw

PATCH 216/332 minmax.h: reduce the #define expansion of min(), max() and clamp()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Laight <[email protected]>

[ Upstream commit b280bb27a9f7c91ddab730e1ad91a9c18a051f41 ]

Since the test for signed values being non-negative only relies on __builtion_constant_p() (not is_constexpr()) it can use the 'ux' variable instead of the caller supplied expression. This means that the #define parameters are only expanded twice. Once in the code and once quoted in the error message.

Cc Andy Shevchenko <[email protected]>
Cc Arnd Bergmann <[email protected]>
Cc Christoph Hellwig <[email protected]>
Cc Dan Carpenter <[email protected]>
Cc Jason A. Donenfeld <[email protected]>
Cc Jens Axboe <[email protected]>
Cc Lorenzo Stoakes <[email protected]>
Cc Mateusz Guzik <[email protected]>
Cc Matthew Wilcox <[email protected]>
Cc Pedro Falcato <[email protected]>
---
 include/linux/minmax.h |   24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)
include/linux/minmax.h +12 -12
@@ -46,10 +46,10 @@
  * comparison, and these expressions only need to be careful to not cause
  * warnings for pointer use.
  */
-#define __signed_type_use(x, ux) (2 + __is_nonneg(x, ux))
-#define __unsigned_type_use(x, ux) (1 + 2 * (sizeof(ux) < 4))
-#define __sign_use(x, ux) (is_signed_type(typeof(ux)) ? \
-	__signed_type_use(x, ux) : __unsigned_type_use(x, ux))
+#define __signed_type_use(ux) (2 + __is_nonneg(ux))
+#define __unsigned_type_use(ux) (1 + 2 * (sizeof(ux) < 4))
+#define __sign_use(ux) (is_signed_type(typeof(ux)) ? \
+	__signed_type_use(ux) : __unsigned_type_use(ux))
 
 /*
  * Check whether a signed value is always non-negative.
@@ -71,13 +71,13 @@
 #else
   #define __signed_type(ux) typeof(__builtin_choose_expr(sizeof(ux) > 4, 1LL, 1L))
 #endif
-#define __is_nonneg(x, ux) statically_true((__signed_type(ux))(x) >= 0)
+#define __is_nonneg(ux) statically_true((__signed_type(ux))(ux) >= 0)
 
-#define __types_ok(x, y, ux, uy) \
-	(__sign_use(x, ux) & __sign_use(y, uy))
+#define __types_ok(ux, uy) \
+	(__sign_use(ux) & __sign_use(uy))
 
-#define __types_ok3(x, y, z, ux, uy, uz) \
-	(__sign_use(x, ux) & __sign_use(y, uy) & __sign_use(z, uz))
+#define __types_ok3(ux, uy, uz) \
+	(__sign_use(ux) & __sign_use(uy) & __sign_use(uz))
 
 #define __cmp_op_min <
 #define __cmp_op_max >
@@ -92,7 +92,7 @@
 
 #define __careful_cmp_once(op, x, y, ux, uy) ({		\
 	__auto_type ux = (x); __auto_type uy = (y);	\
-	BUILD_BUG_ON_MSG(!__types_ok(x, y, ux, uy),	\
+	BUILD_BUG_ON_MSG(!__types_ok(ux, uy),		\
 		#op"("#x", "#y") signedness error");	\
 	__cmp(op, ux, uy); })
 
@@ -109,7 +109,7 @@
 	static_assert(__builtin_choose_expr(__is_constexpr((lo) > (hi)), 	\
 			(lo) <= (hi), true),					\
 		"clamp() low limit " #lo " greater than high limit " #hi);	\
-	BUILD_BUG_ON_MSG(!__types_ok3(val, lo, hi, uval, ulo, uhi),		\
+	BUILD_BUG_ON_MSG(!__types_ok3(uval, ulo, uhi),				\
 		"clamp("#val", "#lo", "#hi") signedness error");		\
 	__clamp(uval, ulo, uhi); })
 
@@ -149,7 +149,7 @@
 
 #define __careful_op3(op, x, y, z, ux, uy, uz) ({			\
 	__auto_type ux = (x); __auto_type uy = (y);__auto_type uz = (z);\
-	BUILD_BUG_ON_MSG(!__types_ok3(x, y, z, ux, uy, uz),		\
+	BUILD_BUG_ON_MSG(!__types_ok3(ux, uy, uz),			\
 		#op"3("#x", "#y", "#z") signedness error");		\
 	__cmp(op, ux, __cmp(op, uy, uz)); })
 
author maintainer
#222 lore raw

PATCH 217/332 minmax.h: use BUILD_BUG_ON_MSG() for the lo < hi test in clamp()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Laight <[email protected]>

[ Upstream commit a5743f32baec4728711bbc01d6ac2b33d4c67040 ]

Use BUILD_BUG_ON_MSG(statically_true(ulo > uhi), ...) for the sanity check of the bounds in clamp(). Gives better error coverage and one less expansion of the arguments.

Cc Andy Shevchenko <[email protected]>
Cc Arnd Bergmann <[email protected]>
Cc Christoph Hellwig <[email protected]>
Cc Dan Carpenter <[email protected]>
Cc Jason A. Donenfeld <[email protected]>
Cc Jens Axboe <[email protected]>
Cc Lorenzo Stoakes <[email protected]>
Cc Mateusz Guzik <[email protected]>
Cc Matthew Wilcox <[email protected]>
Cc Pedro Falcato <[email protected]>
---
 include/linux/minmax.h |    3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
include/linux/minmax.h +1 -2
@@ -106,8 +106,7 @@
 	__auto_type uval = (val);						\
 	__auto_type ulo = (lo);							\
 	__auto_type uhi = (hi);							\
-	static_assert(__builtin_choose_expr(__is_constexpr((lo) > (hi)), 	\
-			(lo) <= (hi), true),					\
+	BUILD_BUG_ON_MSG(statically_true(ulo > uhi),				\
 		"clamp() low limit " #lo " greater than high limit " #hi);	\
 	BUILD_BUG_ON_MSG(!__types_ok3(uval, ulo, uhi),				\
 		"clamp("#val", "#lo", "#hi") signedness error");		\
author maintainer
#223 lore raw

PATCH 218/332 minmax.h: move all the clamp() definitions after the min/max() ones

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Laight <[email protected]>

[ Upstream commit c3939872ee4a6b8bdcd0e813c66823b31e6e26f7 ]

At some point the definitions for clamp() got added in the middle of the ones for min() and max(). Re-order the definitions so they are more sensibly grouped.

Cc Andy Shevchenko <[email protected]>
Cc Arnd Bergmann <[email protected]>
Cc Christoph Hellwig <[email protected]>
Cc Dan Carpenter <[email protected]>
Cc Jason A. Donenfeld <[email protected]>
Cc Jens Axboe <[email protected]>
Cc Lorenzo Stoakes <[email protected]>
Cc Mateusz Guzik <[email protected]>
Cc Matthew Wilcox <[email protected]>
Cc Pedro Falcato <[email protected]>
---
 include/linux/minmax.h |  109 ++++++++++++++++++++++---------------------------
 1 file changed, 51 insertions(+), 58 deletions(-)
include/linux/minmax.h +51 -58
@@ -99,22 +99,6 @@
 #define __careful_cmp(op, x, y) \
 	__careful_cmp_once(op, x, y, __UNIQUE_ID(x_), __UNIQUE_ID(y_))
 
-#define __clamp(val, lo, hi)	\
-	((val) >= (hi) ? (hi) : ((val) <= (lo) ? (lo) : (val)))
-
-#define __clamp_once(val, lo, hi, uval, ulo, uhi) ({				\
-	__auto_type uval = (val);						\
-	__auto_type ulo = (lo);							\
-	__auto_type uhi = (hi);							\
-	BUILD_BUG_ON_MSG(statically_true(ulo > uhi),				\
-		"clamp() low limit " #lo " greater than high limit " #hi);	\
-	BUILD_BUG_ON_MSG(!__types_ok3(uval, ulo, uhi),				\
-		"clamp("#val", "#lo", "#hi") signedness error");		\
-	__clamp(uval, ulo, uhi); })
-
-#define __careful_clamp(val, lo, hi) \
-	__clamp_once(val, lo, hi, __UNIQUE_ID(v_), __UNIQUE_ID(l_), __UNIQUE_ID(h_))
-
 /**
  * min - return minimum of two values of the same or compatible types
  * @x: first value
@@ -171,6 +155,22 @@
 	__careful_op3(max, x, y, z, __UNIQUE_ID(x_), __UNIQUE_ID(y_), __UNIQUE_ID(z_))
 
 /**
+ * min_t - return minimum of two values, using the specified type
+ * @type: data type to use
+ * @x: first value
+ * @y: second value
+ */
+#define min_t(type, x, y) __cmp_once(min, type, x, y)
+
+/**
+ * max_t - return maximum of two values, using the specified type
+ * @type: data type to use
+ * @x: first value
+ * @y: second value
+ */
+#define max_t(type, x, y) __cmp_once(max, type, x, y)
+
+/**
  * min_not_zero - return the minimum that is _not_ zero, unless both are zero
  * @x: value1
  * @y: value2
@@ -180,6 +180,22 @@
 	typeof(y) __y = (y);			\
 	__x == 0 ? __y : ((__y == 0) ? __x : min(__x, __y)); })
 
+#define __clamp(val, lo, hi)	\
+	((val) >= (hi) ? (hi) : ((val) <= (lo) ? (lo) : (val)))
+
+#define __clamp_once(val, lo, hi, uval, ulo, uhi) ({				\
+	__auto_type uval = (val);						\
+	__auto_type ulo = (lo);							\
+	__auto_type uhi = (hi);							\
+	BUILD_BUG_ON_MSG(statically_true(ulo > uhi),				\
+		"clamp() low limit " #lo " greater than high limit " #hi);	\
+	BUILD_BUG_ON_MSG(!__types_ok3(uval, ulo, uhi),				\
+		"clamp("#val", "#lo", "#hi") signedness error");		\
+	__clamp(uval, ulo, uhi); })
+
+#define __careful_clamp(val, lo, hi) \
+	__clamp_once(val, lo, hi, __UNIQUE_ID(v_), __UNIQUE_ID(l_), __UNIQUE_ID(h_))
+
 /**
  * clamp - return a value clamped to a given range with strict typechecking
  * @val: current value
@@ -191,28 +207,30 @@
  */
 #define clamp(val, lo, hi) __careful_clamp(val, lo, hi)
 
-/*
- * ..and if you can't take the strict
- * types, you can specify one yourself.
- *
- * Or not use min/max/clamp at all, of course.
- */
-
 /**
- * min_t - return minimum of two values, using the specified type
- * @type: data type to use
- * @x: first value
- * @y: second value
+ * clamp_t - return a value clamped to a given range using a given type
+ * @type: the type of variable to use
+ * @val: current value
+ * @lo: minimum allowable value
+ * @hi: maximum allowable value
+ *
+ * This macro does no typechecking and uses temporary variables of type
+ * @type to make all the comparisons.
  */
-#define min_t(type, x, y) __cmp_once(min, type, x, y)
+#define clamp_t(type, val, lo, hi) __careful_clamp((type)(val), (type)(lo), (type)(hi))
 
 /**
- * max_t - return maximum of two values, using the specified type
- * @type: data type to use
- * @x: first value
- * @y: second value
+ * clamp_val - return a value clamped to a given range using val's type
+ * @val: current value
+ * @lo: minimum allowable value
+ * @hi: maximum allowable value
+ *
+ * This macro does no typechecking and uses temporary variables of whatever
+ * type the input argument @val is.  This is useful when @val is an unsigned
+ * type and @lo and @hi are literals that will otherwise be assigned a signed
+ * integer type.
  */
-#define max_t(type, x, y) __cmp_once(max, type, x, y)
+#define clamp_val(val, lo, hi) clamp_t(typeof(val), val, lo, hi)
 
 /*
  * Do not check the array parameter using __must_be_array().
@@ -257,31 +275,6 @@
  */
 #define max_array(array, len) __minmax_array(max, array, len)
 
-/**
- * clamp_t - return a value clamped to a given range using a given type
- * @type: the type of variable to use
- * @val: current value
- * @lo: minimum allowable value
- * @hi: maximum allowable value
- *
- * This macro does no typechecking and uses temporary variables of type
- * @type to make all the comparisons.
- */
-#define clamp_t(type, val, lo, hi) __careful_clamp((type)(val), (type)(lo), (type)(hi))
-
-/**
- * clamp_val - return a value clamped to a given range using val's type
- * @val: current value
- * @lo: minimum allowable value
- * @hi: maximum allowable value
- *
- * This macro does no typechecking and uses temporary variables of whatever
- * type the input argument @val is.  This is useful when @val is an unsigned
- * type and @lo and @hi are literals that will otherwise be assigned a signed
- * integer type.
- */
-#define clamp_val(val, lo, hi) clamp_t(typeof(val), val, lo, hi)
-
 static inline bool in_range64(u64 val, u64 start, u64 len)
 {
 	return (val - start) < len;
author maintainer
#224 lore raw

PATCH 219/332 minmax.h: simplify the variants of clamp()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Laight <[email protected]>

[ Upstream commit 495bba17cdf95e9703af1b8ef773c55ef0dfe703 ]

Always pass a 'type' through to __clamp_once(), pass '__auto_type' from clamp() itself.

The expansion of __types_ok3() is reasonable so it isn't worth the added complexity of avoiding it when a fixed type is used for all three values.

Cc Andy Shevchenko <[email protected]>
Cc Arnd Bergmann <[email protected]>
Cc Christoph Hellwig <[email protected]>
Cc Dan Carpenter <[email protected]>
Cc Jason A. Donenfeld <[email protected]>
Cc Jens Axboe <[email protected]>
Cc Lorenzo Stoakes <[email protected]>
Cc Mateusz Guzik <[email protected]>
Cc Matthew Wilcox <[email protected]>
Cc Pedro Falcato <[email protected]>
---
 include/linux/minmax.h |   24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)
include/linux/minmax.h +12 -12
@@ -183,29 +183,29 @@
 #define __clamp(val, lo, hi)	\
 	((val) >= (hi) ? (hi) : ((val) <= (lo) ? (lo) : (val)))
 
-#define __clamp_once(val, lo, hi, uval, ulo, uhi) ({				\
-	__auto_type uval = (val);						\
-	__auto_type ulo = (lo);							\
-	__auto_type uhi = (hi);							\
+#define __clamp_once(type, val, lo, hi, uval, ulo, uhi) ({			\
+	type uval = (val);							\
+	type ulo = (lo);							\
+	type uhi = (hi);							\
 	BUILD_BUG_ON_MSG(statically_true(ulo > uhi),				\
 		"clamp() low limit " #lo " greater than high limit " #hi);	\
 	BUILD_BUG_ON_MSG(!__types_ok3(uval, ulo, uhi),				\
 		"clamp("#val", "#lo", "#hi") signedness error");		\
 	__clamp(uval, ulo, uhi); })
 
-#define __careful_clamp(val, lo, hi) \
-	__clamp_once(val, lo, hi, __UNIQUE_ID(v_), __UNIQUE_ID(l_), __UNIQUE_ID(h_))
+#define __careful_clamp(type, val, lo, hi) \
+	__clamp_once(type, val, lo, hi, __UNIQUE_ID(v_), __UNIQUE_ID(l_), __UNIQUE_ID(h_))
 
 /**
- * clamp - return a value clamped to a given range with strict typechecking
+ * clamp - return a value clamped to a given range with typechecking
  * @val: current value
  * @lo: lowest allowable value
  * @hi: highest allowable value
  *
- * This macro does strict typechecking of @lo/@hi to make sure they are of the
- * same type as @val.  See the unnecessary pointer comparisons.
+ * This macro checks @val/@lo/@hi to make sure they have compatible
+ * signedness.
  */
-#define clamp(val, lo, hi) __careful_clamp(val, lo, hi)
+#define clamp(val, lo, hi) __careful_clamp(__auto_type, val, lo, hi)
 
 /**
  * clamp_t - return a value clamped to a given range using a given type
@@ -217,7 +217,7 @@
  * This macro does no typechecking and uses temporary variables of type
  * @type to make all the comparisons.
  */
-#define clamp_t(type, val, lo, hi) __careful_clamp((type)(val), (type)(lo), (type)(hi))
+#define clamp_t(type, val, lo, hi) __careful_clamp(type, val, lo, hi)
 
 /**
  * clamp_val - return a value clamped to a given range using val's type
@@ -230,7 +230,7 @@
  * type and @lo and @hi are literals that will otherwise be assigned a signed
  * integer type.
  */
-#define clamp_val(val, lo, hi) clamp_t(typeof(val), val, lo, hi)
+#define clamp_val(val, lo, hi) __careful_clamp(typeof(val), val, lo, hi)
 
 /*
  * Do not check the array parameter using __must_be_array().
author maintainer
#225 lore raw

PATCH 220/332 minmax.h: remove some #defines that are only expanded once

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: David Laight <[email protected]>

[ Upstream commit 2b97aaf74ed534fb838d09867d09a3ca5d795208 ]

The bodies of __signed_type_use() and __unsigned_type_use() are much the same size as their names - so put the bodies in the only line that expands them.

Similarly __signed_type() is defined separately for 64bit and then used exactly once just below.

Change the test for __signed_type from CONFIG_64BIT to one based on gcc defined macros so that the code is valid if it gets used outside of a kernel build.

Cc Andy Shevchenko <[email protected]>
Cc Arnd Bergmann <[email protected]>
Cc Christoph Hellwig <[email protected]>
Cc Dan Carpenter <[email protected]>
Cc Jason A. Donenfeld <[email protected]>
Cc Jens Axboe <[email protected]>
Cc Lorenzo Stoakes <[email protected]>
Cc Mateusz Guzik <[email protected]>
Cc Matthew Wilcox <[email protected]>
Cc Pedro Falcato <[email protected]>
---
 include/linux/minmax.h |   14 ++++++--------
 1 file changed, 6 insertions(+), 8 deletions(-)
include/linux/minmax.h +6 -8
@@ -46,10 +46,8 @@
  * comparison, and these expressions only need to be careful to not cause
  * warnings for pointer use.
  */
-#define __signed_type_use(ux) (2 + __is_nonneg(ux))
-#define __unsigned_type_use(ux) (1 + 2 * (sizeof(ux) < 4))
 #define __sign_use(ux) (is_signed_type(typeof(ux)) ? \
-	__signed_type_use(ux) : __unsigned_type_use(ux))
+	(2 + __is_nonneg(ux)) : (1 + 2 * (sizeof(ux) < 4)))
 
 /*
  * Check whether a signed value is always non-negative.
@@ -57,7 +55,7 @@
  * A cast is needed to avoid any warnings from values that aren't signed
  * integer types (in which case the result doesn't matter).
  *
- * On 64-bit any integer or pointer type can safely be cast to 'long'.
+ * On 64-bit any integer or pointer type can safely be cast to 'long long'.
  * But on 32-bit we need to avoid warnings about casting pointers to integers
  * of different sizes without truncating 64-bit values so 'long' or 'long long'
  * must be used depending on the size of the value.
@@ -66,12 +64,12 @@
  * them, but we do not use s128 types in the kernel (we do use 'u128',
  * but they are handled by the !is_signed_type() case).
  */
-#ifdef CONFIG_64BIT
-  #define __signed_type(ux) long
+#if __SIZEOF_POINTER__ == __SIZEOF_LONG_LONG__
+#define __is_nonneg(ux) statically_true((long long)(ux) >= 0)
 #else
-  #define __signed_type(ux) typeof(__builtin_choose_expr(sizeof(ux) > 4, 1LL, 1L))
+#define __is_nonneg(ux) statically_true( \
+	(typeof(__builtin_choose_expr(sizeof(ux) > 4, 1LL, 1L)))(ux) >= 0)
 #endif
-#define __is_nonneg(ux) statically_true((__signed_type(ux))(ux) >= 0)
 
 #define __types_ok(ux, uy) \
 	(__sign_use(ux) & __sign_use(uy))
author maintainer
#226 lore raw

PATCH 221/332 media: pci/ivtv: switch from pci_ to dma_ API

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Christophe JAILLET <[email protected]>

[ Upstream commit 1932dc2f4cf6ac23e48e5fcc24d21adbe35691d1 ]

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below. It has been compile tested.

No memory allocation in involved in this patch, so no GFP_ tweak is needed.

@@ @@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL

@@ @@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE

@@ @@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE

@@ @@
- PCI_DMA_NONE
+ DMA_NONE

@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)

Stable-dep-of: 1069a4fe637d ("media: pci: ivtv: Add missing check after DMA map")

---
 drivers/media/pci/ivtv/ivtv-driver.c  |    2 +-
 drivers/media/pci/ivtv/ivtv-queue.c   |   18 ++++++++++--------
 drivers/media/pci/ivtv/ivtv-streams.c |   22 +++++++++++-----------
 drivers/media/pci/ivtv/ivtv-udma.c    |   19 ++++++++++++-------
 drivers/media/pci/ivtv/ivtv-yuv.c     |   10 +++++++---
 5 files changed, 41 insertions(+), 30 deletions(-)
drivers/media/pci/ivtv/ivtv-driver.c +1 -1
@@ -840,7 +840,7 @@ static int ivtv_setup_pci(struct ivtv *i
 		IVTV_ERR("Can't enable device!\n");
 		return -EIO;
 	}
-	if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
+	if (dma_set_mask(&pdev->dev, DMA_BIT_MASK(32))) {
 		IVTV_ERR("No suitable DMA available.\n");
 		return -EIO;
 	}
drivers/media/pci/ivtv/ivtv-queue.c +10 -8
@@ -188,7 +188,7 @@ int ivtv_stream_alloc(struct ivtv_stream
 		return 0;
 
 	IVTV_DEBUG_INFO("Allocate %s%s stream: %d x %d buffers (%dkB total)\n",
-		s->dma != PCI_DMA_NONE ? "DMA " : "",
+		s->dma != DMA_NONE ? "DMA " : "",
 		s->name, s->buffers, s->buf_size, s->buffers * s->buf_size / 1024);
 
 	s->sg_pending = kzalloc(SGsize, GFP_KERNEL|__GFP_NOWARN);
@@ -218,8 +218,9 @@ int ivtv_stream_alloc(struct ivtv_stream
 		return -ENOMEM;
 	}
 	if (ivtv_might_use_dma(s)) {
-		s->sg_handle = pci_map_single(itv->pdev, s->sg_dma,
-				sizeof(struct ivtv_sg_element), PCI_DMA_TODEVICE);
+		s->sg_handle = dma_map_single(&itv->pdev->dev, s->sg_dma,
+					      sizeof(struct ivtv_sg_element),
+					      DMA_TO_DEVICE);
 		ivtv_stream_sync_for_cpu(s);
 	}
 
@@ -237,7 +238,7 @@ int ivtv_stream_alloc(struct ivtv_stream
 		}
 		INIT_LIST_HEAD(&buf->list);
 		if (ivtv_might_use_dma(s)) {
-			buf->dma_handle = pci_map_single(s->itv->pdev,
+			buf->dma_handle = dma_map_single(&s->itv->pdev->dev,
 				buf->buf, s->buf_size + 256, s->dma);
 			ivtv_buf_sync_for_cpu(s, buf);
 		}
@@ -260,8 +261,8 @@ void ivtv_stream_free(struct ivtv_stream
 	/* empty q_free */
 	while ((buf = ivtv_dequeue(s, &s->q_free))) {
 		if (ivtv_might_use_dma(s))
-			pci_unmap_single(s->itv->pdev, buf->dma_handle,
-				s->buf_size + 256, s->dma);
+			dma_unmap_single(&s->itv->pdev->dev, buf->dma_handle,
+					 s->buf_size + 256, s->dma);
 		kfree(buf->buf);
 		kfree(buf);
 	}
@@ -269,8 +270,9 @@ void ivtv_stream_free(struct ivtv_stream
 	/* Free SG Array/Lists */
 	if (s->sg_dma != NULL) {
 		if (s->sg_handle != IVTV_DMA_UNMAPPED) {
-			pci_unmap_single(s->itv->pdev, s->sg_handle,
-				 sizeof(struct ivtv_sg_element), PCI_DMA_TODEVICE);
+			dma_unmap_single(&s->itv->pdev->dev, s->sg_handle,
+					 sizeof(struct ivtv_sg_element),
+					 DMA_TO_DEVICE);
 			s->sg_handle = IVTV_DMA_UNMAPPED;
 		}
 		kfree(s->sg_pending);
drivers/media/pci/ivtv/ivtv-streams.c +11 -11
@@ -100,7 +100,7 @@ static struct {
 	{	/* IVTV_ENC_STREAM_TYPE_MPG */
 		"encoder MPG",
 		VFL_TYPE_VIDEO, 0,
-		PCI_DMA_FROMDEVICE, 0,
+		DMA_FROM_DEVICE, 0,
 		V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_TUNER |
 			V4L2_CAP_AUDIO | V4L2_CAP_READWRITE,
 		&ivtv_v4l2_enc_fops
@@ -108,7 +108,7 @@ static struct {
 	{	/* IVTV_ENC_STREAM_TYPE_YUV */
 		"encoder YUV",
 		VFL_TYPE_VIDEO, IVTV_V4L2_ENC_YUV_OFFSET,
-		PCI_DMA_FROMDEVICE, 0,
+		DMA_FROM_DEVICE, 0,
 		V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_TUNER |
 			V4L2_CAP_AUDIO | V4L2_CAP_READWRITE,
 		&ivtv_v4l2_enc_fops
@@ -116,7 +116,7 @@ static struct {
 	{	/* IVTV_ENC_STREAM_TYPE_VBI */
 		"encoder VBI",
 		VFL_TYPE_VBI, 0,
-		PCI_DMA_FROMDEVICE, 0,
+		DMA_FROM_DEVICE, 0,
 		V4L2_CAP_VBI_CAPTURE | V4L2_CAP_SLICED_VBI_CAPTURE | V4L2_CAP_TUNER |
 			V4L2_CAP_AUDIO | V4L2_CAP_READWRITE,
 		&ivtv_v4l2_enc_fops
@@ -124,42 +124,42 @@ static struct {
 	{	/* IVTV_ENC_STREAM_TYPE_PCM */
 		"encoder PCM",
 		VFL_TYPE_VIDEO, IVTV_V4L2_ENC_PCM_OFFSET,
-		PCI_DMA_FROMDEVICE, 0,
+		DMA_FROM_DEVICE, 0,
 		V4L2_CAP_TUNER | V4L2_CAP_AUDIO | V4L2_CAP_READWRITE,
 		&ivtv_v4l2_enc_fops
 	},
 	{	/* IVTV_ENC_STREAM_TYPE_RAD */
 		"encoder radio",
 		VFL_TYPE_RADIO, 0,
-		PCI_DMA_NONE, 1,
+		DMA_NONE, 1,
 		V4L2_CAP_RADIO | V4L2_CAP_TUNER,
 		&ivtv_v4l2_radio_fops
 	},
 	{	/* IVTV_DEC_STREAM_TYPE_MPG */
 		"decoder MPG",
 		VFL_TYPE_VIDEO, IVTV_V4L2_DEC_MPG_OFFSET,
-		PCI_DMA_TODEVICE, 0,
+		DMA_TO_DEVICE, 0,
 		V4L2_CAP_VIDEO_OUTPUT | V4L2_CAP_AUDIO | V4L2_CAP_READWRITE,
 		&ivtv_v4l2_dec_fops
 	},
 	{	/* IVTV_DEC_STREAM_TYPE_VBI */
 		"decoder VBI",
 		VFL_TYPE_VBI, IVTV_V4L2_DEC_VBI_OFFSET,
-		PCI_DMA_NONE, 1,
+		DMA_NONE, 1,
 		V4L2_CAP_SLICED_VBI_CAPTURE | V4L2_CAP_READWRITE,
 		&ivtv_v4l2_enc_fops
 	},
 	{	/* IVTV_DEC_STREAM_TYPE_VOUT */
 		"decoder VOUT",
 		VFL_TYPE_VBI, IVTV_V4L2_DEC_VOUT_OFFSET,
-		PCI_DMA_NONE, 1,
+		DMA_NONE, 1,
 		V4L2_CAP_SLICED_VBI_OUTPUT | V4L2_CAP_AUDIO | V4L2_CAP_READWRITE,
 		&ivtv_v4l2_dec_fops
 	},
 	{	/* IVTV_DEC_STREAM_TYPE_YUV */
 		"decoder YUV",
 		VFL_TYPE_VIDEO, IVTV_V4L2_DEC_YUV_OFFSET,
-		PCI_DMA_TODEVICE, 0,
+		DMA_TO_DEVICE, 0,
 		V4L2_CAP_VIDEO_OUTPUT | V4L2_CAP_AUDIO | V4L2_CAP_READWRITE,
 		&ivtv_v4l2_dec_fops
 	}
@@ -179,7 +179,7 @@ static void ivtv_stream_init(struct ivtv
 	s->vdev.device_caps = ivtv_stream_info[type].v4l2_caps;
 
 	if (ivtv_stream_info[type].pio)
-		s->dma = PCI_DMA_NONE;
+		s->dma = DMA_NONE;
 	else
 		s->dma = ivtv_stream_info[type].dma;
 	s->buf_size = itv->stream_buf_size[type];
@@ -217,7 +217,7 @@ static int ivtv_prep_dev(struct ivtv *it
 
 	/* User explicitly selected 0 buffers for these streams, so don't
 	   create them. */
-	if (ivtv_stream_info[type].dma != PCI_DMA_NONE &&
+	if (ivtv_stream_info[type].dma != DMA_NONE &&
 	    itv->options.kilobytes[type] == 0) {
 		IVTV_INFO("Disabled %s device\n", ivtv_stream_info[type].name);
 		return 0;
drivers/media/pci/ivtv/ivtv-udma.c +12 -7
@@ -81,8 +81,10 @@ void ivtv_udma_alloc(struct ivtv *itv)
 {
 	if (itv->udma.SG_handle == 0) {
 		/* Map DMA Page Array Buffer */
-		itv->udma.SG_handle = pci_map_single(itv->pdev, itv->udma.SGarray,
-			   sizeof(itv->udma.SGarray), PCI_DMA_TODEVICE);
+		itv->udma.SG_handle = dma_map_single(&itv->pdev->dev,
+						     itv->udma.SGarray,
+						     sizeof(itv->udma.SGarray),
+						     DMA_TO_DEVICE);
 		ivtv_udma_sync_for_cpu(itv);
 	}
 }
@@ -135,7 +137,8 @@ int ivtv_udma_setup(struct ivtv *itv, un
 	}
 
 	/* Map SG List */
-	dma->SG_length = pci_map_sg(itv->pdev, dma->SGlist, dma->page_count, PCI_DMA_TODEVICE);
+	dma->SG_length = dma_map_sg(&itv->pdev->dev, dma->SGlist,
+				    dma->page_count, DMA_TO_DEVICE);
 
 	/* Fill SG Array with new values */
 	ivtv_udma_fill_sg_array (dma, ivtv_dest_addr, 0, -1);
@@ -159,7 +162,8 @@ void ivtv_udma_unmap(struct ivtv *itv)
 
 	/* Unmap Scatterlist */
 	if (dma->SG_length) {
-		pci_unmap_sg(itv->pdev, dma->SGlist, dma->page_count, PCI_DMA_TODEVICE);
+		dma_unmap_sg(&itv->pdev->dev, dma->SGlist, dma->page_count,
+			     DMA_TO_DEVICE);
 		dma->SG_length = 0;
 	}
 	/* sync DMA */
@@ -175,13 +179,14 @@ void ivtv_udma_free(struct ivtv *itv)
 
 	/* Unmap SG Array */
 	if (itv->udma.SG_handle) {
-		pci_unmap_single(itv->pdev, itv->udma.SG_handle,
-			 sizeof(itv->udma.SGarray), PCI_DMA_TODEVICE);
+		dma_unmap_single(&itv->pdev->dev, itv->udma.SG_handle,
+				 sizeof(itv->udma.SGarray), DMA_TO_DEVICE);
 	}
 
 	/* Unmap Scatterlist */
 	if (itv->udma.SG_length) {
-		pci_unmap_sg(itv->pdev, itv->udma.SGlist, itv->udma.page_count, PCI_DMA_TODEVICE);
+		dma_unmap_sg(&itv->pdev->dev, itv->udma.SGlist,
+			     itv->udma.page_count, DMA_TO_DEVICE);
 	}
 
 	for (i = 0; i < IVTV_DMA_SG_OSD_ENT; i++) {
drivers/media/pci/ivtv/ivtv-yuv.c +7 -3
@@ -113,7 +113,8 @@ static int ivtv_yuv_prep_user_dma(struct
 		dma->page_count = 0;
 		return -ENOMEM;
 	}
-	dma->SG_length = pci_map_sg(itv->pdev, dma->SGlist, dma->page_count, PCI_DMA_TODEVICE);
+	dma->SG_length = dma_map_sg(&itv->pdev->dev, dma->SGlist,
+				    dma->page_count, DMA_TO_DEVICE);
 
 	/* Fill SG Array with new values */
 	ivtv_udma_fill_sg_array(dma, y_buffer_offset, uv_buffer_offset, y_size);
@@ -920,7 +921,9 @@ static void ivtv_yuv_init(struct ivtv *i
 	/* We need a buffer for blanking when Y plane is offset - non-fatal if we can't get one */
 	yi->blanking_ptr = kzalloc(720 * 16, GFP_ATOMIC|__GFP_NOWARN);
 	if (yi->blanking_ptr) {
-		yi->blanking_dmaptr = pci_map_single(itv->pdev, yi->blanking_ptr, 720*16, PCI_DMA_TODEVICE);
+		yi->blanking_dmaptr = dma_map_single(&itv->pdev->dev,
+						     yi->blanking_ptr,
+						     720 * 16, DMA_TO_DEVICE);
 	} else {
 		yi->blanking_dmaptr = 0;
 		IVTV_DEBUG_WARN("Failed to allocate yuv blanking buffer\n");
@@ -1264,7 +1267,8 @@ void ivtv_yuv_close(struct ivtv *itv)
 	if (yi->blanking_ptr) {
 		kfree(yi->blanking_ptr);
 		yi->blanking_ptr = NULL;
-		pci_unmap_single(itv->pdev, yi->blanking_dmaptr, 720*16, PCI_DMA_TODEVICE);
+		dma_unmap_single(&itv->pdev->dev, yi->blanking_dmaptr,
+				 720 * 16, DMA_TO_DEVICE);
 	}
 
 	/* Invalidate the old dimension information */
author maintainer
#227 lore raw

PATCH 222/332 media: pci: ivtv: Add missing check after DMA map

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Thomas Fourier <[email protected]>

[ Upstream commit 1069a4fe637d0e3e4c163e3f8df9be306cc299b4 ]

The DMA map functions can fail and should be tested for errors. If the mapping fails, free blanking_ptr and set it to 0. As 0 is a valid DMA address, use blanking_ptr to test if the DMA address is set.

Fixes 1a0adaf37c30 ("V4L/DVB (5345): ivtv driver for Conexant cx23416/cx23415 MPEG encoder/decoder")
---
 drivers/media/pci/ivtv/ivtv-irq.c |    2 +-
 drivers/media/pci/ivtv/ivtv-yuv.c |    8 +++++++-
 2 files changed, 8 insertions(+), 2 deletions(-)
drivers/media/pci/ivtv/ivtv-irq.c +1 -1
@@ -351,7 +351,7 @@ void ivtv_dma_stream_dec_prepare(struct
 
 	/* Insert buffer block for YUV if needed */
 	if (s->type == IVTV_DEC_STREAM_TYPE_YUV && f->offset_y) {
-		if (yi->blanking_dmaptr) {
+		if (yi->blanking_ptr) {
 			s->sg_pending[idx].src = yi->blanking_dmaptr;
 			s->sg_pending[idx].dst = offset;
 			s->sg_pending[idx].size = 720 * 16;
drivers/media/pci/ivtv/ivtv-yuv.c +7 -1
@@ -120,7 +120,7 @@ static int ivtv_yuv_prep_user_dma(struct
 	ivtv_udma_fill_sg_array(dma, y_buffer_offset, uv_buffer_offset, y_size);
 
 	/* If we've offset the y plane, ensure top area is blanked */
-	if (f->offset_y && yi->blanking_dmaptr) {
+	if (f->offset_y && yi->blanking_ptr) {
 		dma->SGarray[dma->SG_length].size = cpu_to_le32(720*16);
 		dma->SGarray[dma->SG_length].src = cpu_to_le32(yi->blanking_dmaptr);
 		dma->SGarray[dma->SG_length].dst = cpu_to_le32(IVTV_DECODER_OFFSET + yuv_offset[frame]);
@@ -924,6 +924,12 @@ static void ivtv_yuv_init(struct ivtv *i
 		yi->blanking_dmaptr = dma_map_single(&itv->pdev->dev,
 						     yi->blanking_ptr,
 						     720 * 16, DMA_TO_DEVICE);
+		if (dma_mapping_error(&itv->pdev->dev, yi->blanking_dmaptr)) {
+			kfree(yi->blanking_ptr);
+			yi->blanking_ptr = NULL;
+			yi->blanking_dmaptr = 0;
+			IVTV_DEBUG_WARN("Failed to dma_map yuv blanking buffer\n");
+		}
 	} else {
 		yi->blanking_dmaptr = 0;
 		IVTV_DEBUG_WARN("Failed to allocate yuv blanking buffer\n");
author maintainer
#228 lore raw

PATCH 223/332 media: cx18: Add missing check after DMA map

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Thomas Fourier <[email protected]>

[ Upstream commit 23b53639a793477326fd57ed103823a8ab63084f ]

The DMA map functions can fail and should be tested for errors. If the mapping fails, dealloc buffers, and return.

Fixes 1c1e45d17b66 ("V4L/DVB (7786): cx18: new driver for the Conexant CX23418 MPEG encoder chip")
[ removed pci_map_single() replaced by dma_map_single() ]
---
 drivers/media/pci/cx18/cx18-queue.c |   12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)
drivers/media/pci/cx18/cx18-queue.c +10 -2
@@ -379,14 +379,22 @@ int cx18_stream_alloc(struct cx18_stream
 			break;
 		}
 
+		buf->dma_handle = dma_map_single(&s->cx->pci_dev->dev,
+						 buf->buf, s->buf_size,
+						 s->dma);
+		if (dma_mapping_error(&s->cx->pci_dev->dev, buf->dma_handle)) {
+			kfree(buf->buf);
+			kfree(mdl);
+			kfree(buf);
+			break;
+		}
+
 		INIT_LIST_HEAD(&mdl->list);
 		INIT_LIST_HEAD(&mdl->buf_list);
 		mdl->id = s->mdl_base_idx; /* a somewhat safe value */
 		cx18_enqueue(s, mdl, &s->q_idle);
 
 		INIT_LIST_HEAD(&buf->list);
-		buf->dma_handle = pci_map_single(s->cx->pci_dev,
-				buf->buf, s->buf_size, s->dma);
 		cx18_buf_sync_for_cpu(s, buf);
 		list_add_tail(&buf->list, &s->buf_pool);
 	}
author maintainer
#229 lore raw

PATCH 224/332 media: pci: ivtv: Add check for DMA map result

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Mikhail Kobuk <[email protected]>

commit 629913d6d79508b166c66e07e4857e20233d85a9 upstream.

In case DMA fails, 'dma->SG_length' is 0. This value is later used to access 'dma->SGarray[dma->SG_length - 1]', which will cause out of bounds access.

Add check to return early on invalid value. Adjust warnings accordingly.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes 1932dc2f4cf6 ("media: pci/ivtv: switch from 'pci_' to 'dma_' API")
---
 drivers/media/pci/ivtv/ivtv-udma.c |    8 ++++++++
 drivers/media/pci/ivtv/ivtv-yuv.c  |    6 ++++++
 drivers/media/pci/ivtv/ivtvfb.c    |    6 +++---
 3 files changed, 17 insertions(+), 3 deletions(-)
drivers/media/pci/ivtv/ivtv-udma.c +8 -0
@@ -131,6 +131,8 @@ int ivtv_udma_setup(struct ivtv *itv, un
 
 	/* Fill SG List with new values */
 	if (ivtv_udma_fill_sg_list(dma, &user_dma, 0) < 0) {
+		IVTV_DEBUG_WARN("%s: could not allocate bounce buffers for highmem userspace buffers\n",
+				__func__);
 		unpin_user_pages(dma->map, dma->page_count);
 		dma->page_count = 0;
 		return -ENOMEM;
@@ -139,6 +141,12 @@ int ivtv_udma_setup(struct ivtv *itv, un
 	/* Map SG List */
 	dma->SG_length = dma_map_sg(&itv->pdev->dev, dma->SGlist,
 				    dma->page_count, DMA_TO_DEVICE);
+	if (!dma->SG_length) {
+		IVTV_DEBUG_WARN("%s: DMA map error, SG_length is 0\n", __func__);
+		unpin_user_pages(dma->map, dma->page_count);
+		dma->page_count = 0;
+		return -EINVAL;
+	}
 
 	/* Fill SG Array with new values */
 	ivtv_udma_fill_sg_array (dma, ivtv_dest_addr, 0, -1);
drivers/media/pci/ivtv/ivtv-yuv.c +6 -0
@@ -115,6 +115,12 @@ static int ivtv_yuv_prep_user_dma(struct
 	}
 	dma->SG_length = dma_map_sg(&itv->pdev->dev, dma->SGlist,
 				    dma->page_count, DMA_TO_DEVICE);
+	if (!dma->SG_length) {
+		IVTV_DEBUG_WARN("%s: DMA map error, SG_length is 0\n", __func__);
+		unpin_user_pages(dma->map, dma->page_count);
+		dma->page_count = 0;
+		return -EINVAL;
+	}
 
 	/* Fill SG Array with new values */
 	ivtv_udma_fill_sg_array(dma, y_buffer_offset, uv_buffer_offset, y_size);
drivers/media/pci/ivtv/ivtvfb.c +3 -3
@@ -281,10 +281,10 @@ static int ivtvfb_prep_dec_dma_to_device
 	/* Map User DMA */
 	if (ivtv_udma_setup(itv, ivtv_dest_addr, userbuf, size_in_bytes) <= 0) {
 		mutex_unlock(&itv->udma.lock);
-		IVTVFB_WARN("ivtvfb_prep_dec_dma_to_device, Error with pin_user_pages: %d bytes, %d pages returned\n",
-			       size_in_bytes, itv->udma.page_count);
+		IVTVFB_WARN("%s, Error in ivtv_udma_setup: %d bytes, %d pages returned\n",
+			       __func__, size_in_bytes, itv->udma.page_count);
 
-		/* pin_user_pages must have failed completely */
+		/* pin_user_pages or DMA must have failed completely */
 		return -EIO;
 	}
 
author maintainer
#230 lore raw

PATCH 225/332 mm/slab: make __free(kfree) accept error pointers

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Dan Carpenter <[email protected]>

commit cd7eb8f83fcf258f71e293f7fc52a70be8ed0128 upstream.

Currently, if an automatically freed allocation is an error pointer that will lead to a crash. An example of this is in wm831x_gpio_dbg_show().

   171	char *label __free(kfree) = gpiochip_dup_line_label(chip, i);
   172	if (IS_ERR(label)) {
   173		dev_err(wm831x->dev, "Failed to duplicate label\n");
   174		continue;
   175  }

The auto clean up function should check for error pointers as well, otherwise we're going to keep hitting issues like this.

Fixes 54da6a092431 ("locking: Introduce __cleanup() based infrastructure")
---
 include/linux/slab.h |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/linux/slab.h +1 -1
@@ -188,7 +188,7 @@ void kfree_sensitive(const void *);
 size_t __ksize(const void *);
 size_t ksize(const void *);
 
-DEFINE_FREE(kfree, void *, if (_T) kfree(_T))
+DEFINE_FREE(kfree, void *, if (!IS_ERR_OR_NULL(_T)) kfree(_T))
 
 #ifdef CONFIG_HAVE_HARDENED_USERCOPY_ALLOCATOR
 void __check_heap_object(const void *ptr, unsigned long n, struct page *page,
author maintainer
#231 lore raw

PATCH 226/332 wifi: rt2x00: use explicitly signed or unsigned types

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Jason A. Donenfeld <[email protected]>

commit 66063033f77e10b985258126a97573f84bb8d3b4 upstream.

On some platforms, char is unsigned, but this driver, for the most part, assumed it was signed. In other places, it uses char to mean an unsigned number, but only in cases when the values are small. And in still other places, char is used as a boolean. Put an end to this confusion by declaring explicit types, depending on the context.

---
 drivers/net/wireless/ralink/rt2x00/rt2400pci.c |    8 ++---
 drivers/net/wireless/ralink/rt2x00/rt2400pci.h |    2 -
 drivers/net/wireless/ralink/rt2x00/rt2500pci.c |    8 ++---
 drivers/net/wireless/ralink/rt2x00/rt2500pci.h |    2 -
 drivers/net/wireless/ralink/rt2x00/rt2500usb.c |    8 ++---
 drivers/net/wireless/ralink/rt2x00/rt2500usb.h |    2 -
 drivers/net/wireless/ralink/rt2x00/rt2800lib.c |   36 ++++++++++++-------------
 drivers/net/wireless/ralink/rt2x00/rt2800lib.h |    8 ++---
 drivers/net/wireless/ralink/rt2x00/rt2x00usb.c |    6 ++--
 drivers/net/wireless/ralink/rt2x00/rt61pci.c   |    4 +-
 drivers/net/wireless/ralink/rt2x00/rt61pci.h   |    2 -
 drivers/net/wireless/ralink/rt2x00/rt73usb.c   |    4 +-
 drivers/net/wireless/ralink/rt2x00/rt73usb.h   |    2 -
 13 files changed, 46 insertions(+), 46 deletions(-)
drivers/net/wireless/ralink/rt2x00/rt2400pci.c +4 -4
@@ -1023,9 +1023,9 @@ static int rt2400pci_set_state(struct rt
 {
 	u32 reg, reg2;
 	unsigned int i;
-	char put_to_sleep;
-	char bbp_state;
-	char rf_state;
+	bool put_to_sleep;
+	u8 bbp_state;
+	u8 rf_state;
 
 	put_to_sleep = (state != STATE_AWAKE);
 
@@ -1561,7 +1561,7 @@ static int rt2400pci_probe_hw_mode(struc
 {
 	struct hw_mode_spec *spec = &rt2x00dev->spec;
 	struct channel_info *info;
-	char *tx_power;
+	u8 *tx_power;
 	unsigned int i;
 
 	/*
drivers/net/wireless/ralink/rt2x00/rt2400pci.h +1 -1
@@ -939,7 +939,7 @@
 #define DEFAULT_TXPOWER	39
 
 #define __CLAMP_TX(__txpower) \
-	clamp_t(char, (__txpower), MIN_TXPOWER, MAX_TXPOWER)
+	clamp_t(u8, (__txpower), MIN_TXPOWER, MAX_TXPOWER)
 
 #define TXPOWER_FROM_DEV(__txpower) \
 	((__CLAMP_TX(__txpower) - MAX_TXPOWER) + MIN_TXPOWER)
drivers/net/wireless/ralink/rt2x00/rt2500pci.c +4 -4
@@ -1176,9 +1176,9 @@ static int rt2500pci_set_state(struct rt
 {
 	u32 reg, reg2;
 	unsigned int i;
-	char put_to_sleep;
-	char bbp_state;
-	char rf_state;
+	bool put_to_sleep;
+	u8 bbp_state;
+	u8 rf_state;
 
 	put_to_sleep = (state != STATE_AWAKE);
 
@@ -1856,7 +1856,7 @@ static int rt2500pci_probe_hw_mode(struc
 {
 	struct hw_mode_spec *spec = &rt2x00dev->spec;
 	struct channel_info *info;
-	char *tx_power;
+	u8 *tx_power;
 	unsigned int i;
 
 	/*
drivers/net/wireless/ralink/rt2x00/rt2500pci.h +1 -1
@@ -1219,6 +1219,6 @@
 	(((u8)(__txpower)) > MAX_TXPOWER) ? DEFAULT_TXPOWER : (__txpower)
 
 #define TXPOWER_TO_DEV(__txpower) \
-	clamp_t(char, __txpower, MIN_TXPOWER, MAX_TXPOWER)
+	clamp_t(u8, __txpower, MIN_TXPOWER, MAX_TXPOWER)
 
 #endif /* RT2500PCI_H */
drivers/net/wireless/ralink/rt2x00/rt2500usb.c +4 -4
@@ -984,9 +984,9 @@ static int rt2500usb_set_state(struct rt
 	u16 reg;
 	u16 reg2;
 	unsigned int i;
-	char put_to_sleep;
-	char bbp_state;
-	char rf_state;
+	bool put_to_sleep;
+	u8 bbp_state;
+	u8 rf_state;
 
 	put_to_sleep = (state != STATE_AWAKE);
 
@@ -1663,7 +1663,7 @@ static int rt2500usb_probe_hw_mode(struc
 {
 	struct hw_mode_spec *spec = &rt2x00dev->spec;
 	struct channel_info *info;
-	char *tx_power;
+	u8 *tx_power;
 	unsigned int i;
 
 	/*
drivers/net/wireless/ralink/rt2x00/rt2500usb.h +1 -1
@@ -839,6 +839,6 @@
 	(((u8)(__txpower)) > MAX_TXPOWER) ? DEFAULT_TXPOWER : (__txpower)
 
 #define TXPOWER_TO_DEV(__txpower) \
-	clamp_t(char, __txpower, MIN_TXPOWER, MAX_TXPOWER)
+	clamp_t(u8, __txpower, MIN_TXPOWER, MAX_TXPOWER)
 
 #endif /* RT2500USB_H */
drivers/net/wireless/ralink/rt2x00/rt2800lib.c +18 -18
@@ -3297,10 +3297,10 @@ static void rt2800_config_channel_rf53xx
 	if (rt2x00_has_cap_bt_coexist(rt2x00dev)) {
 		if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390F)) {
 			/* r55/r59 value array of channel 1~14 */
-			static const char r55_bt_rev[] = {0x83, 0x83,
+			static const u8 r55_bt_rev[] = {0x83, 0x83,
 				0x83, 0x73, 0x73, 0x63, 0x53, 0x53,
 				0x53, 0x43, 0x43, 0x43, 0x43, 0x43};
-			static const char r59_bt_rev[] = {0x0e, 0x0e,
+			static const u8 r59_bt_rev[] = {0x0e, 0x0e,
 				0x0e, 0x0e, 0x0e, 0x0b, 0x0a, 0x09,
 				0x07, 0x07, 0x07, 0x07, 0x07, 0x07};
 
@@ -3309,7 +3309,7 @@ static void rt2800_config_channel_rf53xx
 			rt2800_rfcsr_write(rt2x00dev, 59,
 					   r59_bt_rev[idx]);
 		} else {
-			static const char r59_bt[] = {0x8b, 0x8b, 0x8b,
+			static const u8 r59_bt[] = {0x8b, 0x8b, 0x8b,
 				0x8b, 0x8b, 0x8b, 0x8b, 0x8a, 0x89,
 				0x88, 0x88, 0x86, 0x85, 0x84};
 
@@ -3317,10 +3317,10 @@ static void rt2800_config_channel_rf53xx
 		}
 	} else {
 		if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390F)) {
-			static const char r55_nonbt_rev[] = {0x23, 0x23,
+			static const u8 r55_nonbt_rev[] = {0x23, 0x23,
 				0x23, 0x23, 0x13, 0x13, 0x03, 0x03,
 				0x03, 0x03, 0x03, 0x03, 0x03, 0x03};
-			static const char r59_nonbt_rev[] = {0x07, 0x07,
+			static const u8 r59_nonbt_rev[] = {0x07, 0x07,
 				0x07, 0x07, 0x07, 0x07, 0x07, 0x07,
 				0x07, 0x07, 0x06, 0x05, 0x04, 0x04};
 
@@ -3331,14 +3331,14 @@ static void rt2800_config_channel_rf53xx
 		} else if (rt2x00_rt(rt2x00dev, RT5390) ||
 			   rt2x00_rt(rt2x00dev, RT5392) ||
 			   rt2x00_rt(rt2x00dev, RT6352)) {
-			static const char r59_non_bt[] = {0x8f, 0x8f,
+			static const u8 r59_non_bt[] = {0x8f, 0x8f,
 				0x8f, 0x8f, 0x8f, 0x8f, 0x8f, 0x8d,
 				0x8a, 0x88, 0x88, 0x87, 0x87, 0x86};
 
 			rt2800_rfcsr_write(rt2x00dev, 59,
 					   r59_non_bt[idx]);
 		} else if (rt2x00_rt(rt2x00dev, RT5350)) {
-			static const char r59_non_bt[] = {0x0b, 0x0b,
+			static const u8 r59_non_bt[] = {0x0b, 0x0b,
 				0x0b, 0x0b, 0x0b, 0x0b, 0x0b, 0x0a,
 				0x0a, 0x09, 0x08, 0x07, 0x07, 0x06};
 
@@ -3961,23 +3961,23 @@ static void rt2800_iq_calibrate(struct r
 	rt2800_bbp_write(rt2x00dev, 159, cal != 0xff ? cal : 0);
 }
 
-static char rt2800_txpower_to_dev(struct rt2x00_dev *rt2x00dev,
+static s8 rt2800_txpower_to_dev(struct rt2x00_dev *rt2x00dev,
 				  unsigned int channel,
-				  char txpower)
+				  s8 txpower)
 {
 	if (rt2x00_rt(rt2x00dev, RT3593) ||
 	    rt2x00_rt(rt2x00dev, RT3883))
 		txpower = rt2x00_get_field8(txpower, EEPROM_TXPOWER_ALC);
 
 	if (channel <= 14)
-		return clamp_t(char, txpower, MIN_G_TXPOWER, MAX_G_TXPOWER);
+		return clamp_t(s8, txpower, MIN_G_TXPOWER, MAX_G_TXPOWER);
 
 	if (rt2x00_rt(rt2x00dev, RT3593) ||
 	    rt2x00_rt(rt2x00dev, RT3883))
-		return clamp_t(char, txpower, MIN_A_TXPOWER_3593,
+		return clamp_t(s8, txpower, MIN_A_TXPOWER_3593,
 			       MAX_A_TXPOWER_3593);
 	else
-		return clamp_t(char, txpower, MIN_A_TXPOWER, MAX_A_TXPOWER);
+		return clamp_t(s8, txpower, MIN_A_TXPOWER, MAX_A_TXPOWER);
 }
 
 static void rt3883_bbp_adjust(struct rt2x00_dev *rt2x00dev,
@@ -8473,11 +8473,11 @@ static int rt2800_rf_lp_config(struct rt
 	return 0;
 }
 
-static char rt2800_lp_tx_filter_bw_cal(struct rt2x00_dev *rt2x00dev)
+static s8 rt2800_lp_tx_filter_bw_cal(struct rt2x00_dev *rt2x00dev)
 {
 	unsigned int cnt;
 	u8 bbp_val;
-	char cal_val;
+	s8 cal_val;
 
 	rt2800_bbp_dcoc_write(rt2x00dev, 0, 0x82);
 
@@ -8509,7 +8509,7 @@ static void rt2800_bw_filter_calibration
 	u8 rx_filter_target_20m = 0x27, rx_filter_target_40m = 0x31;
 	int loop = 0, is_ht40, cnt;
 	u8 bbp_val, rf_val;
-	char cal_r32_init, cal_r32_val, cal_diff;
+	s8 cal_r32_init, cal_r32_val, cal_diff;
 	u8 saverfb5r00, saverfb5r01, saverfb5r03, saverfb5r04, saverfb5r05;
 	u8 saverfb5r06, saverfb5r07;
 	u8 saverfb5r08, saverfb5r17, saverfb5r18, saverfb5r19, saverfb5r20;
@@ -9960,9 +9960,9 @@ static int rt2800_probe_hw_mode(struct r
 {
 	struct hw_mode_spec *spec = &rt2x00dev->spec;
 	struct channel_info *info;
-	char *default_power1;
-	char *default_power2;
-	char *default_power3;
+	s8 *default_power1;
+	s8 *default_power2;
+	s8 *default_power3;
 	unsigned int i, tx_chains, rx_chains;
 	u32 reg;
 
drivers/net/wireless/ralink/rt2x00/rt2800lib.h +4 -4
@@ -22,10 +22,10 @@
 struct rt2800_drv_data {
 	u8 calibration_bw20;
 	u8 calibration_bw40;
-	char rx_calibration_bw20;
-	char rx_calibration_bw40;
-	char tx_calibration_bw20;
-	char tx_calibration_bw40;
+	s8 rx_calibration_bw20;
+	s8 rx_calibration_bw40;
+	s8 tx_calibration_bw20;
+	s8 tx_calibration_bw40;
 	u8 bbp25;
 	u8 bbp26;
 	u8 txmixer_gain_24g;
drivers/net/wireless/ralink/rt2x00/rt2x00usb.c +3 -3
@@ -117,12 +117,12 @@ int rt2x00usb_vendor_request_buff(struct
 				  const u16 buffer_length)
 {
 	int status = 0;
-	unsigned char *tb;
+	u8 *tb;
 	u16 off, len, bsize;
 
 	mutex_lock(&rt2x00dev->csr_mutex);
 
-	tb  = (char *)buffer;
+	tb  = (u8 *)buffer;
 	off = offset;
 	len = buffer_length;
 	while (len && !status) {
@@ -215,7 +215,7 @@ void rt2x00usb_register_read_async(struc
 	rd->cr.wLength = cpu_to_le16(sizeof(u32));
 
 	usb_fill_control_urb(urb, usb_dev, usb_rcvctrlpipe(usb_dev, 0),
-			     (unsigned char *)(&rd->cr), &rd->reg, sizeof(rd->reg),
+			     (u8 *)(&rd->cr), &rd->reg, sizeof(rd->reg),
 			     rt2x00usb_register_read_async_cb, rd);
 	usb_anchor_urb(urb, rt2x00dev->anchor);
 	if (usb_submit_urb(urb, GFP_ATOMIC) < 0) {
drivers/net/wireless/ralink/rt2x00/rt61pci.c +2 -2
@@ -1709,7 +1709,7 @@ static int rt61pci_set_state(struct rt2x
 {
 	u32 reg, reg2;
 	unsigned int i;
-	char put_to_sleep;
+	bool put_to_sleep;
 
 	put_to_sleep = (state != STATE_AWAKE);
 
@@ -2656,7 +2656,7 @@ static int rt61pci_probe_hw_mode(struct
 {
 	struct hw_mode_spec *spec = &rt2x00dev->spec;
 	struct channel_info *info;
-	char *tx_power;
+	u8 *tx_power;
 	unsigned int i;
 
 	/*
drivers/net/wireless/ralink/rt2x00/rt61pci.h +1 -1
@@ -1484,6 +1484,6 @@ struct hw_pairwise_ta_entry {
 	(((u8)(__txpower)) > MAX_TXPOWER) ? DEFAULT_TXPOWER : (__txpower)
 
 #define TXPOWER_TO_DEV(__txpower) \
-	clamp_t(char, __txpower, MIN_TXPOWER, MAX_TXPOWER)
+	clamp_t(u8, __txpower, MIN_TXPOWER, MAX_TXPOWER)
 
 #endif /* RT61PCI_H */
drivers/net/wireless/ralink/rt2x00/rt73usb.c +2 -2
@@ -1378,7 +1378,7 @@ static int rt73usb_set_state(struct rt2x
 {
 	u32 reg, reg2;
 	unsigned int i;
-	char put_to_sleep;
+	bool put_to_sleep;
 
 	put_to_sleep = (state != STATE_AWAKE);
 
@@ -2090,7 +2090,7 @@ static int rt73usb_probe_hw_mode(struct
 {
 	struct hw_mode_spec *spec = &rt2x00dev->spec;
 	struct channel_info *info;
-	char *tx_power;
+	u8 *tx_power;
 	unsigned int i;
 
 	/*
drivers/net/wireless/ralink/rt2x00/rt73usb.h +1 -1
@@ -1063,6 +1063,6 @@ struct hw_pairwise_ta_entry {
 	(((u8)(__txpower)) > MAX_TXPOWER) ? DEFAULT_TXPOWER : (__txpower)
 
 #define TXPOWER_TO_DEV(__txpower) \
-	clamp_t(char, __txpower, MIN_TXPOWER, MAX_TXPOWER)
+	clamp_t(u8, __txpower, MIN_TXPOWER, MAX_TXPOWER)
 
 #endif /* RT73USB_H */
author maintainer
#232 lore raw

PATCH 227/332 jbd2: ensure that all ongoing I/O complete before freeing blocks

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Zhang Yi <[email protected]>

commit 3c652c3a71de1d30d72dc82c3bead8deb48eb749 upstream.

When releasing file system metadata blocks in jbd2_journal_forget(), if this buffer has not yet been checkpointed, it may have already been written back, currently be in the process of being written back, or has not yet written back. jbd2_journal_forget() calls jbd2_journal_try_remove_checkpoint() to check the buffer's status and add it to the current transaction if it has not been written back. This buffer can only be reallocated after the transaction is committed.

jbd2_journal_try_remove_checkpoint() attempts to lock the buffer and check its dirty status while holding the buffer lock. If the buffer has already been written back, everything proceeds normally. However, there are two issues. First, the function returns immediately if the buffer is locked by the write-back process. It does not wait for the write-back to complete. Consequently, until the current transaction is committed and the block is reallocated, there is no guarantee that the I/O will complete. This means that ongoing I/O could write stale metadata to the newly allocated block, potentially corrupting data. Second, the function unlocks the buffer as soon as it detects that the buffer is still dirty. If a concurrent write-back occurs immediately after this unlocking and before clear_buffer_dirty() is called in jbd2_journal_forget(), data corruption can theoretically still occur.

Although these two issues are unlikely to occur in practice since the undergoing metadata writeback I/O does not take this long to complete, it's better to explicitly ensure that all ongoing I/O operations are completed.

Fixes 597599268e3b ("jbd2: discard dirty data when forgetting an un-journalled buffer")

Message-ID: <[email protected]>

---
 fs/jbd2/transaction.c |   13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)
fs/jbd2/transaction.c +9 -4
@@ -1642,6 +1642,7 @@ int jbd2_journal_forget(handle_t *handle
 	int drop_reserve = 0;
 	int err = 0;
 	int was_modified = 0;
+	int wait_for_writeback = 0;
 
 	if (is_handle_aborted(handle))
 		return -EROFS;
@@ -1766,18 +1767,22 @@ int jbd2_journal_forget(handle_t *handle
 		}
 
 		/*
-		 * The buffer is still not written to disk, we should
-		 * attach this buffer to current transaction so that the
-		 * buffer can be checkpointed only after the current
-		 * transaction commits.
+		 * The buffer has not yet been written to disk. We should
+		 * either clear the buffer or ensure that the ongoing I/O
+		 * is completed, and attach this buffer to current
+		 * transaction so that the buffer can be checkpointed only
+		 * after the current transaction commits.
 		 */
 		clear_buffer_dirty(bh);
+		wait_for_writeback = 1;
 		__jbd2_journal_file_buffer(jh, transaction, BJ_Forget);
 		spin_unlock(&journal->j_list_lock);
 	}
 drop:
 	__brelse(bh);
 	spin_unlock(&jh->b_state_lock);
+	if (wait_for_writeback)
+		wait_on_buffer(bh);
 	jbd2_journal_put_journal_head(jh);
 	if (drop_reserve) {
 		/* no need to reserve log space for this block -bzzz */
author maintainer
#233 lore raw

PATCH 228/332 ext4: detect invalid INLINE_DATA + EXTENTS flag combination

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Deepanshu Kartikey <[email protected]>

commit 1d3ad183943b38eec2acf72a0ae98e635dc8456b upstream.

syzbot reported a BUG_ON in ext4_es_cache_extent() when opening a verity file on a corrupted ext4 filesystem mounted without a journal.

The issue is that the filesystem has an inode with both the INLINE_DATA and EXTENTS flags set:

EXT4-fs error (device loop0): ext4_cache_extents:545: inode #15:
comm syz.0.17: corrupted extent tree: lblk 0 < prev 66

Investigation revealed that the inode has both flags set:

    DEBUG: inode 15 - flag=1, i_inline_off=164, has_inline=1, extents_flag=1

This is an invalid combination since an inode should have either:
- INLINE_DATA: data stored directly in the inode
- EXTENTS: data stored in extent-mapped blocks

Having both flags causes ext4_has_inline_data() to return true, skipping extent tree validation in __ext4_iget(). The unvalidated out-of-order extents then trigger a BUG_ON in ext4_es_cache_extent() due to integer underflow when calculating hole sizes.

Fix this by detecting this invalid flag combination early in ext4_iget() and rejecting the corrupted inode.

Message-ID: <[email protected]>

---
 fs/ext4/inode.c |    8 ++++++++
 1 file changed, 8 insertions(+)
fs/ext4/inode.c +8 -0
@@ -4868,6 +4868,14 @@ struct inode *__ext4_iget(struct super_b
 	}
 	ei->i_flags = le32_to_cpu(raw_inode->i_flags);
 	ext4_set_inode_flags(inode, true);
+	/* Detect invalid flag combination - can't have both inline data and extents */
+	if (ext4_test_inode_flag(inode, EXT4_INODE_INLINE_DATA) &&
+	    ext4_test_inode_flag(inode, EXT4_INODE_EXTENTS)) {
+		ext4_error_inode(inode, function, line, 0,
+			"inode has both inline data and extents flags");
+		ret = -EFSCORRUPTED;
+		goto bad_inode;
+	}
 	inode->i_blocks = ext4_inode_blocks(raw_inode, ei);
 	ei->i_file_acl = le32_to_cpu(raw_inode->i_file_acl_lo);
 	if (ext4_has_feature_64bit(sb))
author maintainer
#234 lore raw

PATCH 229/332 pwm: berlin: Fix wrong register in suspend/resume

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Jisheng Zhang <[email protected]>

commit 3a4b9d027e4061766f618292df91760ea64a1fcc upstream.

The 'enable' register should be BERLIN_PWM_EN rather than BERLIN_PWM_ENABLE, otherwise, the driver accesses wrong address, there will be cpu exception then kernel panic during suspend/resume.

Fixes bbf0722c1c66 ("pwm: berlin: Add suspend/resume support")
[ukleinek: backport to 5.10]
---
 drivers/pwm/pwm-berlin.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/pwm/pwm-berlin.c +2 -2
@@ -249,7 +249,7 @@ static int berlin_pwm_suspend(struct dev
 		if (!channel)
 			continue;
 
-		channel->enable = berlin_pwm_readl(pwm, i, BERLIN_PWM_ENABLE);
+		channel->enable = berlin_pwm_readl(pwm, i, BERLIN_PWM_EN);
 		channel->ctrl = berlin_pwm_readl(pwm, i, BERLIN_PWM_CONTROL);
 		channel->duty = berlin_pwm_readl(pwm, i, BERLIN_PWM_DUTY);
 		channel->tcnt = berlin_pwm_readl(pwm, i, BERLIN_PWM_TCNT);
@@ -280,7 +280,7 @@ static int berlin_pwm_resume(struct devi
 		berlin_pwm_writel(pwm, i, channel->ctrl, BERLIN_PWM_CONTROL);
 		berlin_pwm_writel(pwm, i, channel->duty, BERLIN_PWM_DUTY);
 		berlin_pwm_writel(pwm, i, channel->tcnt, BERLIN_PWM_TCNT);
-		berlin_pwm_writel(pwm, i, channel->enable, BERLIN_PWM_ENABLE);
+		berlin_pwm_writel(pwm, i, channel->enable, BERLIN_PWM_EN);
 	}
 
 	return 0;
author maintainer
#235 lore raw

PATCH 230/332 blk-crypto: fix missing blktrace bio split events

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Yu Kuai <[email protected]>

[ Upstream commit 06d712d297649f48ebf1381d19bd24e942813b37 ]

trace_block_split() is missing, resulting in blktrace inability to catch BIO split events and making it harder to analyze the BIO sequence.

Fixes 488f6682c832 ("block: blk-crypto-fallback for Inline Encryption")
[ added queue parameter to trace_block_split() call ]
---
 block/blk-crypto-fallback.c |    3 +++
 1 file changed, 3 insertions(+)
block/blk-crypto-fallback.c +3 -0
@@ -18,6 +18,7 @@
 #include <linux/mempool.h>
 #include <linux/module.h>
 #include <linux/random.h>
+#include <trace/events/block.h>
 
 #include "blk-crypto-internal.h"
 
@@ -227,7 +228,9 @@ static bool blk_crypto_split_bio_if_need
 			bio->bi_status = BLK_STS_RESOURCE;
 			return false;
 		}
+
 		bio_chain(split_bio, bio);
+		trace_block_split(bio->bi_disk->queue, split_bio, bio->bi_iter.bi_sector);
 		submit_bio_noacct(bio);
 		*bio_ptr = split_bio;
 	}
author maintainer
#236 lore raw

PATCH 231/332 btrfs: avoid potential out-of-bounds in btrfs_encode_fh()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Anderson Nascimento <[email protected]>

[ Upstream commit dff4f9ff5d7f289e4545cc936362e01ed3252742 ]

The function btrfs_encode_fh() does not properly account for the three cases it handles.

Before writing to the file handle (fh), the function only returns to the user BTRFS_FID_SIZE_NON_CONNECTABLE (5 dwords, 20 bytes) or BTRFS_FID_SIZE_CONNECTABLE (8 dwords, 32 bytes).

However, when a parent exists and the root ID of the parent and the inode are different, the function writes BTRFS_FID_SIZE_CONNECTABLE_ROOT (10 dwords, 40 bytes).

If *max_len is not large enough, this write goes out of bounds because BTRFS_FID_SIZE_CONNECTABLE_ROOT is greater than BTRFS_FID_SIZE_CONNECTABLE originally returned.

This results in an 8-byte out-of-bounds write at
fid->parent_root_objectid = parent_root_id.

A previous attempt to fix this issue was made but was lost.

https://lore.kernel.org/all/[email protected]/

Although this issue does not seem to be easily triggerable, it is a potential memory corruption bug that should be fixed. This patch resolves the issue by ensuring the function returns the appropriate size for all three cases and validates that *max_len is large enough before writing any data.

Fixes be6e8dc0ba84 ("NFS support for btrfs - v3")
[ replaced btrfs_root_id() calls with direct ->root->root_key.objectid access ]
---
 fs/btrfs/export.c |    8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
fs/btrfs/export.c +7 -1
@@ -22,7 +22,11 @@ static int btrfs_encode_fh(struct inode
 	int type;
 
 	if (parent && (len < BTRFS_FID_SIZE_CONNECTABLE)) {
-		*max_len = BTRFS_FID_SIZE_CONNECTABLE;
+		if (BTRFS_I(inode)->root->root_key.objectid !=
+		    BTRFS_I(parent)->root->root_key.objectid)
+			*max_len = BTRFS_FID_SIZE_CONNECTABLE_ROOT;
+		else
+			*max_len = BTRFS_FID_SIZE_CONNECTABLE;
 		return FILEID_INVALID;
 	} else if (len < BTRFS_FID_SIZE_NON_CONNECTABLE) {
 		*max_len = BTRFS_FID_SIZE_NON_CONNECTABLE;
@@ -44,6 +48,8 @@ static int btrfs_encode_fh(struct inode
 		parent_root_id = BTRFS_I(parent)->root->root_key.objectid;
 
 		if (parent_root_id != fid->root_objectid) {
+			if (*max_len < BTRFS_FID_SIZE_CONNECTABLE_ROOT)
+				return FILEID_INVALID;
 			fid->parent_root_objectid = parent_root_id;
 			len = BTRFS_FID_SIZE_CONNECTABLE_ROOT;
 			type = FILEID_BTRFS_WITH_PARENT_ROOT;
author maintainer
#237 lore raw

PATCH 232/332 bus: mhi: host: Do not use uninitialized dev pointer in mhi_init_irq_setup()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Adam Xue <[email protected]>

[ Upstream commit d0856a6dff57f95cc5d2d74e50880f01697d0cc4 ]

In mhi_init_irq_setup, the device pointer used for dev_err() was not initialized. Use the pointer from mhi_cntrl instead.

Fixes b0fc0167f254 ("bus: mhi: core: Allow shared IRQ for event rings")
Fixes 3000f85b8f47 ("bus: mhi: core: Add support for basic PM operations")
[mani: reworded subject/description and CCed stable]
[ Adjust context ]
---
 drivers/bus/mhi/host/init.c |    5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)
drivers/bus/mhi/host/init.c +2 -3
@@ -147,7 +147,6 @@ void mhi_deinit_free_irq(struct mhi_cont
 int mhi_init_irq_setup(struct mhi_controller *mhi_cntrl)
 {
 	struct mhi_event *mhi_event = mhi_cntrl->mhi_event;
-	struct device *dev = &mhi_cntrl->mhi_dev->dev;
 	int i, ret;
 
 	/* Setup BHI_INTVEC IRQ */
@@ -163,7 +162,7 @@ int mhi_init_irq_setup(struct mhi_contro
 			continue;
 
 		if (mhi_event->irq >= mhi_cntrl->nr_irqs) {
-			dev_err(dev, "irq %d not available for event ring\n",
+			dev_err(mhi_cntrl->cntrl_dev, "irq %d not available for event ring\n",
 				mhi_event->irq);
 			ret = -EINVAL;
 			goto error_request;
@@ -174,7 +173,7 @@ int mhi_init_irq_setup(struct mhi_contro
 				  IRQF_SHARED | IRQF_NO_SUSPEND,
 				  "mhi", mhi_event);
 		if (ret) {
-			dev_err(dev, "Error requesting irq:%d for ev:%d\n",
+			dev_err(mhi_cntrl->cntrl_dev, "Error requesting irq:%d for ev:%d\n",
 				mhi_cntrl->irq[mhi_event->irq], i);
 			goto error_request;
 		}
author maintainer
#238 lore raw

PATCH 233/332 drm/exynos: exynos7_drm_decon: remove ctx->suspended

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Kaustabh Chakraborty <[email protected]>

[ Upstream commit e1361a4f1be9cb69a662c6d7b5ce218007d6e82b ]

Condition guards are found to be redundant, as the call flow is properly managed now, as also observed in the Exynos5433 DECON driver. Since state checking is no longer necessary, remove it.

This also fixes an issue which prevented decon_commit() from decon_atomic_enable() due to an incorrect state change setting.

Fixes 96976c3d9aff ("drm/exynos: Add DECON driver")
[ Adjust context ]
---
 drivers/gpu/drm/exynos/exynos7_drm_decon.c |   36 -----------------------------
 1 file changed, 36 deletions(-)
drivers/gpu/drm/exynos/exynos7_drm_decon.c +0 -36
@@ -51,7 +51,6 @@ struct decon_context {
 	void __iomem			*regs;
 	unsigned long			irq_flags;
 	bool				i80_if;
-	bool				suspended;
 	wait_queue_head_t		wait_vsync_queue;
 	atomic_t			wait_vsync_event;
 
@@ -85,9 +84,6 @@ static void decon_wait_for_vblank(struct
 {
 	struct decon_context *ctx = crtc->ctx;
 
-	if (ctx->suspended)
-		return;
-
 	atomic_set(&ctx->wait_vsync_event, 1);
 
 	/*
@@ -155,9 +151,6 @@ static void decon_commit(struct exynos_d
 	struct drm_display_mode *mode = &crtc->base.state->adjusted_mode;
 	u32 val, clkdiv;
 
-	if (ctx->suspended)
-		return;
-
 	/* nothing to do if we haven't set the mode yet */
 	if (mode->htotal == 0 || mode->vtotal == 0)
 		return;
@@ -219,9 +212,6 @@ static int decon_enable_vblank(struct ex
 	struct decon_context *ctx = crtc->ctx;
 	u32 val;
 
-	if (ctx->suspended)
-		return -EPERM;
-
 	if (!test_and_set_bit(0, &ctx->irq_flags)) {
 		val = readl(ctx->regs + VIDINTCON0);
 
@@ -244,9 +234,6 @@ static void decon_disable_vblank(struct
 	struct decon_context *ctx = crtc->ctx;
 	u32 val;
 
-	if (ctx->suspended)
-		return;
-
 	if (test_and_clear_bit(0, &ctx->irq_flags)) {
 		val = readl(ctx->regs + VIDINTCON0);
 
@@ -369,9 +356,6 @@ static void decon_atomic_begin(struct ex
 	struct decon_context *ctx = crtc->ctx;
 	int i;
 
-	if (ctx->suspended)
-		return;
-
 	for (i = 0; i < WINDOWS_NR; i++)
 		decon_shadow_protect_win(ctx, i, true);
 }
@@ -391,9 +375,6 @@ static void decon_update_plane(struct ex
 	unsigned int cpp = fb->format->cpp[0];
 	unsigned int pitch = fb->pitches[0];
 
-	if (ctx->suspended)
-		return;
-
 	/*
 	 * SHADOWCON/PRTCON register is used for enabling timing.
 	 *
@@ -481,9 +462,6 @@ static void decon_disable_plane(struct e
 	unsigned int win = plane->index;
 	u32 val;
 
-	if (ctx->suspended)
-		return;
-
 	/* protect windows */
 	decon_shadow_protect_win(ctx, win, true);
 
@@ -502,9 +480,6 @@ static void decon_atomic_flush(struct ex
 	struct decon_context *ctx = crtc->ctx;
 	int i;
 
-	if (ctx->suspended)
-		return;
-
 	for (i = 0; i < WINDOWS_NR; i++)
 		decon_shadow_protect_win(ctx, i, false);
 	exynos_crtc_handle_event(crtc);
@@ -531,9 +506,6 @@ static void decon_atomic_enable(struct e
 {
 	struct decon_context *ctx = crtc->ctx;
 
-	if (!ctx->suspended)
-		return;
-
 	pm_runtime_get_sync(ctx->dev);
 
 	decon_init(ctx);
@@ -543,8 +515,6 @@ static void decon_atomic_enable(struct e
 		decon_enable_vblank(ctx->crtc);
 
 	decon_commit(ctx->crtc);
-
-	ctx->suspended = false;
 }
 
 static void decon_atomic_disable(struct exynos_drm_crtc *crtc)
@@ -552,9 +522,6 @@ static void decon_atomic_disable(struct
 	struct decon_context *ctx = crtc->ctx;
 	int i;
 
-	if (ctx->suspended)
-		return;
-
 	/*
 	 * We need to make sure that all windows are disabled before we
 	 * suspend that connector. Otherwise we might try to scan from
@@ -564,8 +531,6 @@ static void decon_atomic_disable(struct
 		decon_disable_plane(crtc, &ctx->planes[i]);
 
 	pm_runtime_put_sync(ctx->dev);
-
-	ctx->suspended = true;
 }
 
 static const struct exynos_drm_crtc_ops decon_crtc_ops = {
@@ -687,7 +652,6 @@ static int decon_probe(struct platform_d
 		return -ENOMEM;
 
 	ctx->dev = dev;
-	ctx->suspended = true;
 
 	i80_if_timings = of_get_child_by_name(dev->of_node, "i80-if-timings");
 	if (i80_if_timings)
author maintainer
#239 lore raw

PATCH 234/332 media: rc: Directly use ida_free()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: keliu <[email protected]>

[ Upstream commit cd54ff938091d890edf78e6555ec30c63dcd2eb5 ]

Use ida_alloc() and ida_free() instead of the deprecated ida_simple_get() and ida_simple_remove().

Stable-dep-of: 4f4098c57e13 ("media: lirc: Fix error handling in lirc_register()")

---
 drivers/media/rc/lirc_dev.c |    6 +++---
 drivers/media/rc/rc-main.c  |    6 +++---
 2 files changed, 6 insertions(+), 6 deletions(-)
drivers/media/rc/lirc_dev.c +3 -3
@@ -731,7 +731,7 @@ int lirc_register(struct rc_dev *dev)
 	const char *rx_type, *tx_type;
 	int err, minor;
 
-	minor = ida_simple_get(&lirc_ida, 0, RC_DEV_MAX, GFP_KERNEL);
+	minor = ida_alloc_max(&lirc_ida, RC_DEV_MAX - 1, GFP_KERNEL);
 	if (minor < 0)
 		return minor;
 
@@ -776,7 +776,7 @@ int lirc_register(struct rc_dev *dev)
 	return 0;
 
 out_ida:
-	ida_simple_remove(&lirc_ida, minor);
+	ida_free(&lirc_ida, minor);
 	return err;
 }
 
@@ -794,7 +794,7 @@ void lirc_unregister(struct rc_dev *dev)
 	spin_unlock_irqrestore(&dev->lirc_fh_lock, flags);
 
 	cdev_device_del(&dev->lirc_cdev, &dev->lirc_dev);
-	ida_simple_remove(&lirc_ida, MINOR(dev->lirc_dev.devt));
+	ida_free(&lirc_ida, MINOR(dev->lirc_dev.devt));
 }
 
 int __init lirc_dev_init(void)
drivers/media/rc/rc-main.c +3 -3
@@ -1897,7 +1897,7 @@ int rc_register_device(struct rc_dev *de
 	if (!dev)
 		return -EINVAL;
 
-	minor = ida_simple_get(&rc_ida, 0, RC_DEV_MAX, GFP_KERNEL);
+	minor = ida_alloc_max(&rc_ida, RC_DEV_MAX - 1, GFP_KERNEL);
 	if (minor < 0)
 		return minor;
 
@@ -1980,7 +1980,7 @@ out_rx_free:
 out_raw:
 	ir_raw_event_free(dev);
 out_minor:
-	ida_simple_remove(&rc_ida, minor);
+	ida_free(&rc_ida, minor);
 	return rc;
 }
 EXPORT_SYMBOL_GPL(rc_register_device);
@@ -2040,7 +2040,7 @@ void rc_unregister_device(struct rc_dev
 
 	device_del(&dev->dev);
 
-	ida_simple_remove(&rc_ida, dev->minor);
+	ida_free(&rc_ida, dev->minor);
 
 	if (!dev->managed_alloc)
 		rc_free_device(dev);
author maintainer
#240 lore raw

PATCH 235/332 media: lirc: Fix error handling in lirc_register()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Ma Ke <[email protected]>

[ Upstream commit 4f4098c57e139ad972154077fb45c3e3141555dd ]

When cdev_device_add() failed, calling put_device() to explicitly release dev->lirc_dev. Otherwise, it could cause the fault of the reference count.

Found by code review.

Fixes a6ddd4fecbb0 ("media: lirc: remove last remnants of lirc kapi")
---
 drivers/media/rc/lirc_dev.c |    9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/media/rc/lirc_dev.c +5 -4
@@ -747,11 +747,11 @@ int lirc_register(struct rc_dev *dev)
 
 	cdev_init(&dev->lirc_cdev, &lirc_fops);
 
+	get_device(&dev->dev);
+
 	err = cdev_device_add(&dev->lirc_cdev, &dev->lirc_dev);
 	if (err)
-		goto out_ida;
-
-	get_device(&dev->dev);
+		goto out_put_device;
 
 	switch (dev->driver_type) {
 	case RC_DRIVER_SCANCODE:
@@ -775,7 +775,8 @@ int lirc_register(struct rc_dev *dev)
 
 	return 0;
 
-out_ida:
+out_put_device:
+	put_device(&dev->lirc_dev);
 	ida_free(&lirc_ida, minor);
 	return err;
 }
author maintainer
#241 lore raw

PATCH 236/332 xen/events: Update virq_to_irq on migration

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Jason Andryuk <[email protected]>

[ Upstream commit 3fcc8e146935415d69ffabb5df40ecf50e106131 ]

VIRQs come in 3 flavors, per-VPU, per-domain, and global, and the VIRQs are tracked in per-cpu virq_to_irq arrays.

Per-domain and global VIRQs must be bound on CPU 0, and bind_virq_to_irq() sets the per_cpu virq_to_irq at registration time Later, the interrupt can migrate, and info->cpu is updated. When calling __unbind_from_irq(), the per-cpu virq_to_irq is cleared for a different cpu. If bind_virq_to_irq() is called again with CPU 0, the stale irq is returned. There won't be any irq_info for the irq, so things break.

Make xen_rebind_evtchn_to_cpu() update the per_cpu virq_to_irq mappings to keep them update to date with the current cpu. This ensures the correct virq_to_irq is cleared in __unbind_from_irq().

Fixes e46cdb66c8fc ("xen: event channels")

Message-ID: <[email protected]>

---
 drivers/xen/events/events_base.c |   13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)
drivers/xen/events/events_base.c +12 -1
@@ -1746,9 +1746,20 @@ static int xen_rebind_evtchn_to_cpu(stru
 	 * virq or IPI channel, which don't actually need to be rebound. Ignore
 	 * it, but don't do the xenlinux-level rebind in that case.
 	 */
-	if (HYPERVISOR_event_channel_op(EVTCHNOP_bind_vcpu, &bind_vcpu) >= 0)
+	if (HYPERVISOR_event_channel_op(EVTCHNOP_bind_vcpu, &bind_vcpu) >= 0) {
+		int old_cpu = info->cpu;
+
 		bind_evtchn_to_cpu(evtchn, tcpu);
 
+		if (info->type == IRQT_VIRQ) {
+			int virq = info->u.virq;
+			int irq = per_cpu(virq_to_irq, old_cpu)[virq];
+
+			per_cpu(virq_to_irq, old_cpu)[virq] = -1;
+			per_cpu(virq_to_irq, tcpu)[virq] = irq;
+		}
+	}
+
 	do_unmask(info, EVT_MASK_REASON_TEMPORARY);
 
 	return 0;
author maintainer
#242 lore raw

PATCH 237/332 HID: multitouch: fix sticky fingers

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Benjamin Tissoires <[email protected]>

commit 46f781e0d151844589dc2125c8cce3300546f92a upstream.

The sticky fingers quirk (MT_QUIRK_STICKY_FINGERS) was only considering the case when slots were not released during the last report. This can be problematic if the firmware forgets to release a finger while others are still present.

This was observed on the Synaptics DLL0945 touchpad found on the Dell XPS 9310 and the Dell Inspiron 5406.

Fixes 4f4001bc76fd ("HID: multitouch: fix rare Win 8 cases when the touch up event gets missing")
---
 drivers/hid/hid-multitouch.c |   27 ++++++++++++++-------------
 1 file changed, 14 insertions(+), 13 deletions(-)
drivers/hid/hid-multitouch.c +14 -13
@@ -81,9 +81,8 @@ enum latency_mode {
 	HID_LATENCY_HIGH = 1,
 };
 
-#define MT_IO_FLAGS_RUNNING		0
-#define MT_IO_FLAGS_ACTIVE_SLOTS	1
-#define MT_IO_FLAGS_PENDING_SLOTS	2
+#define MT_IO_SLOTS_MASK		GENMASK(7, 0) /* reserve first 8 bits for slot tracking */
+#define MT_IO_FLAGS_RUNNING		32
 
 static const bool mtrue = true;		/* default for true */
 static const bool mfalse;		/* default for false */
@@ -159,7 +158,11 @@ struct mt_device {
 	struct mt_class mtclass;	/* our mt device class */
 	struct timer_list release_timer;	/* to release sticky fingers */
 	struct hid_device *hdev;	/* hid_device we're attached to */
-	unsigned long mt_io_flags;	/* mt flags (MT_IO_FLAGS_*) */
+	unsigned long mt_io_flags;	/* mt flags (MT_IO_FLAGS_RUNNING)
+					 * first 8 bits are reserved for keeping the slot
+					 * states, this is fine because we only support up
+					 * to 250 slots (MT_MAX_MAXCONTACT)
+					 */
 	__u8 inputmode_value;	/* InputMode HID feature value */
 	__u8 maxcontacts;
 	bool is_buttonpad;	/* is this device a button pad? */
@@ -904,6 +907,7 @@ static void mt_release_pending_palms(str
 
 	for_each_set_bit(slotnum, app->pending_palm_slots, td->maxcontacts) {
 		clear_bit(slotnum, app->pending_palm_slots);
+		clear_bit(slotnum, &td->mt_io_flags);
 
 		input_mt_slot(input, slotnum);
 		input_mt_report_slot_inactive(input);
@@ -935,12 +939,6 @@ static void mt_sync_frame(struct mt_devi
 
 	app->num_received = 0;
 	app->left_button_state = 0;
-
-	if (test_bit(MT_IO_FLAGS_ACTIVE_SLOTS, &td->mt_io_flags))
-		set_bit(MT_IO_FLAGS_PENDING_SLOTS, &td->mt_io_flags);
-	else
-		clear_bit(MT_IO_FLAGS_PENDING_SLOTS, &td->mt_io_flags);
-	clear_bit(MT_IO_FLAGS_ACTIVE_SLOTS, &td->mt_io_flags);
 }
 
 static int mt_compute_timestamp(struct mt_application *app, __s32 value)
@@ -1094,7 +1092,9 @@ static int mt_process_slot(struct mt_dev
 		input_event(input, EV_ABS, ABS_MT_TOUCH_MAJOR, major);
 		input_event(input, EV_ABS, ABS_MT_TOUCH_MINOR, minor);
 
-		set_bit(MT_IO_FLAGS_ACTIVE_SLOTS, &td->mt_io_flags);
+		set_bit(slotnum, &td->mt_io_flags);
+	} else {
+		clear_bit(slotnum, &td->mt_io_flags);
 	}
 
 	return 0;
@@ -1229,7 +1229,7 @@ static void mt_touch_report(struct hid_d
 	 * defect.
 	 */
 	if (app->quirks & MT_QUIRK_STICKY_FINGERS) {
-		if (test_bit(MT_IO_FLAGS_PENDING_SLOTS, &td->mt_io_flags))
+		if (td->mt_io_flags & MT_IO_SLOTS_MASK)
 			mod_timer(&td->release_timer,
 				  jiffies + msecs_to_jiffies(100));
 		else
@@ -1647,6 +1647,7 @@ static void mt_release_contacts(struct h
 			for (i = 0; i < mt->num_slots; i++) {
 				input_mt_slot(input_dev, i);
 				input_mt_report_slot_inactive(input_dev);
+				clear_bit(i, &td->mt_io_flags);
 			}
 			input_mt_sync_frame(input_dev);
 			input_sync(input_dev);
@@ -1669,7 +1670,7 @@ static void mt_expired_timeout(struct ti
 	 */
 	if (test_and_set_bit_lock(MT_IO_FLAGS_RUNNING, &td->mt_io_flags))
 		return;
-	if (test_bit(MT_IO_FLAGS_PENDING_SLOTS, &td->mt_io_flags))
+	if (td->mt_io_flags & MT_IO_SLOTS_MASK)
 		mt_release_contacts(hdev);
 	clear_bit_unlock(MT_IO_FLAGS_RUNNING, &td->mt_io_flags);
 }
author maintainer
#243 lore raw

PATCH 238/332 iomap: add the new iomap_iter model

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Christoph Hellwig <[email protected]>

[ Upstream commit f4b896c213f0752adc828ddc11bd55419ffab248 ]

The iomap_iter struct provides a convenient way to package up and maintain all the arguments to the various mapping and operation functions. It is operated on using the iomap_iter() function that is called in loop until the whole range has been processed. Compared to the existing iomap_apply() function this avoid an indirect call for each iteration.

For now iomap_iter() calls back into the existing ->iomap_begin and ->iomap_end methods, but in the future this could be further optimized to avoid indirect calls entirely.

Based on an earlier patch from Matthew Wilcox <[email protected]>.

[djwong: add to apply.c to preserve git history of iomap loop control]

Stable-dep-of: 154d1e7ad9e5 ("dax: skip read lock assertion for read-only filesystems")

---
 fs/iomap/apply.c      | 74 ++++++++++++++++++++++++++++++++++++++++++-
 fs/iomap/trace.h      | 37 +++++++++++++++++++++-
 include/linux/iomap.h | 56 ++++++++++++++++++++++++++++++++
 3 files changed, 165 insertions(+), 2 deletions(-)
fs/iomap/apply.c +73 -1
index 26ab6563181fc..e82647aef7ead 100644
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
  * Copyright (C) 2010 Red Hat, Inc.
- * Copyright (c) 2016-2018 Christoph Hellwig.
+ * Copyright (c) 2016-2021 Christoph Hellwig.
  */
 #include <linux/module.h>
 #include <linux/compiler.h>
@@ -97,3 +97,75 @@ iomap_apply(struct inode *inode, loff_t pos, loff_t length, unsigned flags,
 
 	return written ? written : ret;
 }
+
+static inline int iomap_iter_advance(struct iomap_iter *iter)
+{
+	/* handle the previous iteration (if any) */
+	if (iter->iomap.length) {
+		if (iter->processed <= 0)
+			return iter->processed;
+		if (WARN_ON_ONCE(iter->processed > iomap_length(iter)))
+			return -EIO;
+		iter->pos += iter->processed;
+		iter->len -= iter->processed;
+		if (!iter->len)
+			return 0;
+	}
+
+	/* clear the state for the next iteration */
+	iter->processed = 0;
+	memset(&iter->iomap, 0, sizeof(iter->iomap));
+	memset(&iter->srcmap, 0, sizeof(iter->srcmap));
+	return 1;
+}
+
+static inline void iomap_iter_done(struct iomap_iter *iter)
+{
+	WARN_ON_ONCE(iter->iomap.offset > iter->pos);
+	WARN_ON_ONCE(iter->iomap.length == 0);
+	WARN_ON_ONCE(iter->iomap.offset + iter->iomap.length <= iter->pos);
+
+	trace_iomap_iter_dstmap(iter->inode, &iter->iomap);
+	if (iter->srcmap.type != IOMAP_HOLE)
+		trace_iomap_iter_srcmap(iter->inode, &iter->srcmap);
+}
+
+/**
+ * iomap_iter - iterate over a ranges in a file
+ * @iter: iteration structue
+ * @ops: iomap ops provided by the file system
+ *
+ * Iterate over filesystem-provided space mappings for the provided file range.
+ *
+ * This function handles cleanup of resources acquired for iteration when the
+ * filesystem indicates there are no more space mappings, which means that this
+ * function must be called in a loop that continues as long it returns a
+ * positive value.  If 0 or a negative value is returned, the caller must not
+ * return to the loop body.  Within a loop body, there are two ways to break out
+ * of the loop body:  leave @iter.processed unchanged, or set it to a negative
+ * errno.
+ */
+int iomap_iter(struct iomap_iter *iter, const struct iomap_ops *ops)
+{
+	int ret;
+
+	if (iter->iomap.length && ops->iomap_end) {
+		ret = ops->iomap_end(iter->inode, iter->pos, iomap_length(iter),
+				iter->processed > 0 ? iter->processed : 0,
+				iter->flags, &iter->iomap);
+		if (ret < 0 && !iter->processed)
+			return ret;
+	}
+
+	trace_iomap_iter(iter, ops, _RET_IP_);
+	ret = iomap_iter_advance(iter);
+	if (ret <= 0)
+		return ret;
+
+	ret = ops->iomap_begin(iter->inode, iter->pos, iter->len, iter->flags,
+			       &iter->iomap, &iter->srcmap);
+	if (ret < 0)
+		return ret;
+	iomap_iter_done(iter);
+	return 1;
+}
fs/iomap/trace.h +36 -1
index fdc7ae388476f..52b850b4d3f44 100644
@@ -1,6 +1,6 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 /*
- * Copyright (c) 2009-2019 Christoph Hellwig
+ * Copyright (c) 2009-2021 Christoph Hellwig
  *
  * NOTE: none of these tracepoints shall be consider a stable kernel ABI
  * as they can change at any time.
@@ -140,6 +140,8 @@ DEFINE_EVENT(iomap_class, name,	\
 	TP_ARGS(inode, iomap))
 DEFINE_IOMAP_EVENT(iomap_apply_dstmap);
 DEFINE_IOMAP_EVENT(iomap_apply_srcmap);
+DEFINE_IOMAP_EVENT(iomap_iter_dstmap);
+DEFINE_IOMAP_EVENT(iomap_iter_srcmap);
 
 TRACE_EVENT(iomap_apply,
 	TP_PROTO(struct inode *inode, loff_t pos, loff_t length,
@@ -179,6 +181,39 @@ TRACE_EVENT(iomap_apply,
 		   __entry->actor)
 );
 
+TRACE_EVENT(iomap_iter,
+	TP_PROTO(struct iomap_iter *iter, const void *ops,
+		 unsigned long caller),
+	TP_ARGS(iter, ops, caller),
+	TP_STRUCT__entry(
+		__field(dev_t, dev)
+		__field(u64, ino)
+		__field(loff_t, pos)
+		__field(loff_t, length)
+		__field(unsigned int, flags)
+		__field(const void *, ops)
+		__field(unsigned long, caller)
+	),
+	TP_fast_assign(
+		__entry->dev = iter->inode->i_sb->s_dev;
+		__entry->ino = iter->inode->i_ino;
+		__entry->pos = iter->pos;
+		__entry->length = iomap_length(iter);
+		__entry->flags = iter->flags;
+		__entry->ops = ops;
+		__entry->caller = caller;
+	),
+	TP_printk("dev %d:%d ino 0x%llx pos %lld length %lld flags %s (0x%x) ops %ps caller %pS",
+		  MAJOR(__entry->dev), MINOR(__entry->dev),
+		   __entry->ino,
+		   __entry->pos,
+		   __entry->length,
+		   __print_flags(__entry->flags, "|", IOMAP_FLAGS_STRINGS),
+		   __entry->flags,
+		   __entry->ops,
+		   (void *)__entry->caller)
+);
+
 #endif /* _IOMAP_TRACE_H */
 
 #undef TRACE_INCLUDE_PATH
include/linux/iomap.h +56 -0

62 lines not on this page · raw message

Signature · 1 line
2.51.0
author maintainer
#244 lore raw

PATCH 239/332 fsdax: switch dax_iomap_rw to use iomap_iter

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Christoph Hellwig <[email protected]>

[ Upstream commit ca289e0b95afa973d204c77a4ad5c37e06145fbf ]

Switch the dax_iomap_rw implementation to use iomap_iter.

Stable-dep-of: 154d1e7ad9e5 ("dax: skip read lock assertion for read-only filesystems")

---
 fs/dax.c | 49 ++++++++++++++++++++++++-------------------------
 1 file changed, 24 insertions(+), 25 deletions(-)
fs/dax.c +24 -25
index 3e7e9a57fd28c..6619a71b57bbe 100644
@@ -1104,20 +1104,21 @@ s64 dax_iomap_zero(loff_t pos, u64 length, struct iomap *iomap)
 	return size;
 }
 
-static loff_t
-dax_iomap_actor(struct inode *inode, loff_t pos, loff_t length, void *data,
-		struct iomap *iomap, struct iomap *srcmap)
+static loff_t dax_iomap_iter(const struct iomap_iter *iomi,
+		struct iov_iter *iter)
 {
+	const struct iomap *iomap = &iomi->iomap;
+	loff_t length = iomap_length(iomi);
+	loff_t pos = iomi->pos;
 	struct block_device *bdev = iomap->bdev;
 	struct dax_device *dax_dev = iomap->dax_dev;
-	struct iov_iter *iter = data;
 	loff_t end = pos + length, done = 0;
 	ssize_t ret = 0;
 	size_t xfer;
 	int id;
 
 	if (iov_iter_rw(iter) == READ) {
-		end = min(end, i_size_read(inode));
+		end = min(end, i_size_read(iomi->inode));
 		if (pos >= end)
 			return 0;
 
@@ -1134,7 +1135,7 @@ dax_iomap_actor(struct inode *inode, loff_t pos, loff_t length, void *data,
 	 * written by write(2) is visible in mmap.
 	 */
 	if (iomap->flags & IOMAP_F_NEW) {
-		invalidate_inode_pages2_range(inode->i_mapping,
+		invalidate_inode_pages2_range(iomi->inode->i_mapping,
 					      pos >> PAGE_SHIFT,
 					      (end - 1) >> PAGE_SHIFT);
 	}
@@ -1210,31 +1211,29 @@ ssize_t
 dax_iomap_rw(struct kiocb *iocb, struct iov_iter *iter,
 		const struct iomap_ops *ops)
 {
-	struct address_space *mapping = iocb->ki_filp->f_mapping;
-	struct inode *inode = mapping->host;
-	loff_t pos = iocb->ki_pos, ret = 0, done = 0;
-	unsigned flags = 0;
+	struct iomap_iter iomi = {
+		.inode		= iocb->ki_filp->f_mapping->host,
+		.pos		= iocb->ki_pos,
+		.len		= iov_iter_count(iter),
+	};
+	loff_t done = 0;
+	int ret;
 
 	if (iov_iter_rw(iter) == WRITE) {
-		lockdep_assert_held_write(&inode->i_rwsem);
-		flags |= IOMAP_WRITE;
+		lockdep_assert_held_write(&iomi.inode->i_rwsem);
+		iomi.flags |= IOMAP_WRITE;
 	} else {
-		lockdep_assert_held(&inode->i_rwsem);
+		lockdep_assert_held(&iomi.inode->i_rwsem);
 	}
 
 	if (iocb->ki_flags & IOCB_NOWAIT)
-		flags |= IOMAP_NOWAIT;
+		iomi.flags |= IOMAP_NOWAIT;
 
-	while (iov_iter_count(iter)) {
-		ret = iomap_apply(inode, pos, iov_iter_count(iter), flags, ops,
-				iter, dax_iomap_actor);
-		if (ret <= 0)
-			break;
-		pos += ret;
-		done += ret;
-	}
+	while ((ret = iomap_iter(&iomi, ops)) > 0)
+		iomi.processed = dax_iomap_iter(&iomi, iter);
 
-	iocb->ki_pos += done;
+	done = iomi.pos - iocb->ki_pos;
+	iocb->ki_pos = iomi.pos;
 	return done ? done : ret;
 }
 EXPORT_SYMBOL_GPL(dax_iomap_rw);
@@ -1308,7 +1307,7 @@ static vm_fault_t dax_iomap_pte_fault(struct vm_fault *vmf, pfn_t *pfnp,
 	}
 
 	/*
-	 * Note that we don't bother to use iomap_apply here: DAX required
+	 * Note that we don't bother to use iomap_iter here: DAX required
 	 * the file system block size to be equal the page size, which means
 	 * that we never have to deal with more than a single extent here.
 	 */
@@ -1562,7 +1561,7 @@ static vm_fault_t dax_iomap_pmd_fault(struct vm_fault *vmf, pfn_t *pfnp,
 	}
 
 	/*
-	 * Note that we don't use iomap_apply here.  We aren't doing I/O, only
+	 * Note that we don't use iomap_iter here.  We aren't doing I/O, only
 	 * setting up a mapping, so really we're using iomap_begin() as a way
 	 * to look up our filesystem block.
 	 */
Signature · 1 line
2.51.0
#245 lore raw

Re: [PATCH 5.10 239/332] fsdax: switch dax_iomap_rw to use iomap_iter

Quoted 24 lines · Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Christoph Hellwig <[email protected]>

[ Upstream commit ca289e0b95afa973d204c77a4ad5c37e06145fbf ]

Switch the dax_iomap_rw implementation to use iomap_iter.

Stable-dep-of: 154d1e7ad9e5 ("dax: skip read lock assertion for read-only filesystems")

---
 fs/dax.c | 49 ++++++++++++++++++++++++-------------------------
 1 file changed, 24 insertions(+), 25 deletions(-)
fs/dax.c +0 -0
index 3e7e9a57fd28c..6619a71b57bbe 100644

fs/dax.c s64 dax_iomap_zero(loff_t pos, u64 length, struct iomap *iomap) · line 1110

Quoted 10 lines
fs/dax.c +3 -3
@@ -1104,20 +1104,21 @@ s64 dax_iomap_zero(loff_t pos, u64 length, struct iomap *iomap)
 	return size;
 }
 
-static loff_t
-dax_iomap_actor(struct inode *inode, loff_t pos, loff_t length, void *data,
-		struct iomap *iomap, struct iomap *srcmap)
+static loff_t dax_iomap_iter(const struct iomap_iter *iomi,
+		struct iov_iter *iter)
 {
+	const struct iomap *iomap = &iomi->iomap;

The constification of iomap in this change depends on commit 7e4f4b2d689d ("fsdax: mark the iomap argument to dax_iomap_sector as const") from the upstream series to avoid compiler warnings, which may be fatal in the case of clang since it is a subwarning of -Wincompatible-pointer-types:

fs/dax.c: In function 'dax_iomap_iter':
fs/dax.c:1147:58: warning: passing argument 1 of 'dax_iomap_sector' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
1147 | const sector_t sector = dax_iomap_sector(iomap, pos);
| ^~~~~
fs/dax.c:1009:48: note: expected 'struct iomap *' but argument is of type 'const struct iomap *'
1009 | static sector_t dax_iomap_sector(struct iomap *iomap, loff_t pos)

        |                                  ~~~~~~~~~~~~~~^~~~~

fs/dax.c:1147:44: error: passing 'const struct iomap *' to parameter of type 'struct iomap *' discards qualifiers [-Werror,-Wincompatible-pointer-types-discards-qualifiers]
1147 | const sector_t sector = dax_iomap_sector(iomap, pos);
| ^~~~~
fs/dax.c:1009:48: note: passing argument to parameter 'iomap' here
1009 | static sector_t dax_iomap_sector(struct iomap *iomap, loff_t pos)
| ^

Cheers,
Nathan

author maintainer
#246 lore raw

PATCH 240/332 dax: skip read lock assertion for read-only filesystems

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Yuezhang Mo <[email protected]>

[ Upstream commit 154d1e7ad9e5ce4b2aaefd3862b3dba545ad978d ]

The commit 168316db3583("dax: assert that i_rwsem is held exclusive for writes") added lock assertions to ensure proper locking in DAX operations. However, these assertions trigger false-positive lockdep warnings since read lock is unnecessary on read-only filesystems(e.g., erofs).

This patch skips the read lock assertion for read-only filesystems, eliminating the spurious warnings while maintaining the integrity checks for writable filesystems.

Fixes 168316db3583 ("dax: assert that i_rwsem is held exclusive for writes")
---
 fs/dax.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
fs/dax.c +1 -1
index 6619a71b57bbe..a6f481f1517dd 100644
@@ -1222,7 +1222,7 @@ dax_iomap_rw(struct kiocb *iocb, struct iov_iter *iter,
 	if (iov_iter_rw(iter) == WRITE) {
 		lockdep_assert_held_write(&iomi.inode->i_rwsem);
 		iomi.flags |= IOMAP_WRITE;
-	} else {
+	} else if (!sb_rdonly(iomi.inode->i_sb)) {
 		lockdep_assert_held(&iomi.inode->i_rwsem);
 	}
 
Signature · 1 line
2.51.0
author maintainer
#247 lore raw

PATCH 241/332 net: dlink: handle dma_map_single() failure properly

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Yeounsu Moon <[email protected]>

[ Upstream commit 65946eac6d888d50ae527c4e5c237dbe5cc3a2f2 ]

There is no error handling for dma_map_single() failures.

Add error handling by checking dma_mapping_error() and freeing the skb using dev_kfree_skb() (process context) when it fails.

Fixes 1da177e4c3f4 ("Linux-2.6.12-rc2")

Tested-on: D-Link DGE-550T Rev-A3

---
 drivers/net/ethernet/dlink/dl2k.c | 23 ++++++++++++++++-------
 1 file changed, 16 insertions(+), 7 deletions(-)
drivers/net/ethernet/dlink/dl2k.c +16 -7
index 0af58c4dcebc1..dc85a742f97cb 100644
@@ -499,25 +499,34 @@ static int alloc_list(struct net_device *dev)
 	for (i = 0; i < RX_RING_SIZE; i++) {
 		/* Allocated fixed size of skbuff */
 		struct sk_buff *skb;
+		dma_addr_t addr;
 
 		skb = netdev_alloc_skb_ip_align(dev, np->rx_buf_sz);
 		np->rx_skbuff[i] = skb;
-		if (!skb) {
-			free_list(dev);
-			return -ENOMEM;
-		}
+		if (!skb)
+			goto err_free_list;
+
+		addr = dma_map_single(&np->pdev->dev, skb->data,
+				      np->rx_buf_sz, DMA_FROM_DEVICE);
+		if (dma_mapping_error(&np->pdev->dev, addr))
+			goto err_kfree_skb;
 
 		np->rx_ring[i].next_desc = cpu_to_le64(np->rx_ring_dma +
 						((i + 1) % RX_RING_SIZE) *
 						sizeof(struct netdev_desc));
 		/* Rubicon now supports 40 bits of addressing space. */
-		np->rx_ring[i].fraginfo =
-		    cpu_to_le64(dma_map_single(&np->pdev->dev, skb->data,
-					       np->rx_buf_sz, DMA_FROM_DEVICE));
+		np->rx_ring[i].fraginfo = cpu_to_le64(addr);
 		np->rx_ring[i].fraginfo |= cpu_to_le64((u64)np->rx_buf_sz << 48);
 	}
 
 	return 0;
+
+err_kfree_skb:
+	dev_kfree_skb(np->rx_skbuff[i]);
+	np->rx_skbuff[i] = NULL;
+err_free_list:
+	free_list(dev);
+	return -ENOMEM;
 }
 
 static void rio_hw_init(struct net_device *dev)
Signature · 1 line
2.51.0
author maintainer
#248 lore raw

PATCH 242/332 r8169: fix packet truncation after S4 resume on RTL8168H/RTL8111H

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Linmao Li <[email protected]>

[ Upstream commit 70f92ab97042f243e1c8da1c457ff56b9b3e49f1 ]

After resume from S4 (hibernate), RTL8168H/RTL8111H truncates incoming packets. Packet captures show messages like "IP truncated-ip - 146 bytes missing!".

The issue is caused by RxConfig not being properly re-initialized after resume. Re-initializing the RxConfig register before the chip re-initialization sequence avoids the truncation and restores correct packet reception.

This follows the same pattern as commit ef9da46ddef0 ("r8169: fix data corruption issue on RTL8402").

---
 drivers/net/ethernet/realtek/r8169_main.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/net/ethernet/realtek/r8169_main.c +3 -2
index b60add52f4497..9fb8fdd5b2619 100644
@@ -4979,8 +4979,9 @@ static int __maybe_unused rtl8169_resume(struct device *device)
 	if (!device_may_wakeup(tp_to_dev(tp)))
 		clk_prepare_enable(tp->clk);
 
-	/* Reportedly at least Asus X453MA truncates packets otherwise */
-	if (tp->mac_version == RTL_GIGA_MAC_VER_37)
+	/* Some chip versions may truncate packets without this initialization */
+	if (tp->mac_version == RTL_GIGA_MAC_VER_37 ||
+	    tp->mac_version == RTL_GIGA_MAC_VER_46)
 		rtl_init_rxcfg(tp);
 
 	return rtl8169_net_resume(tp);
Signature · 1 line
2.51.0
author maintainer
#249 lore raw

PATCH 243/332 net/ip6_tunnel: Prevent perpetual tunnel growth

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Dmitry Safonov <[email protected]>

[ Upstream commit 21f4d45eba0b2dcae5dbc9e5e0ad08735c993f16 ]

Similarly to ipv4 tunnel, ipv6 version updates dev->needed_headroom, too. While ipv4 tunnel headroom adjustment growth was limited in commit 5ae1e9922bbd ("net: ip_tunnel: prevent perpetual headroom growth"), ipv6 tunnel yet increases the headroom without any ceiling.

Reflect ipv4 tunnel headroom adjustment limit on ipv6 version.

Credits to Francesco Ruggeri, who was originally debugging this issue and wrote local Arista-specific patch and a reproducer.

Fixes 8eb30be0352d ("ipv6: Create ip6_tnl_xmit")
Cc Florian Westphal <[email protected]>
Cc Francesco Ruggeri <[email protected]>
---
 include/net/ip_tunnels.h | 15 +++++++++++++++
 net/ipv4/ip_tunnel.c     | 14 --------------
 net/ipv6/ip6_tunnel.c    |  3 +--
 3 files changed, 16 insertions(+), 16 deletions(-)
include/net/ip_tunnels.h +15 -0
index cedf72924f19e..d7a037d32bcc2 100644
@@ -468,6 +468,21 @@ struct metadata_dst *iptunnel_metadata_reply(struct metadata_dst *md,
 int skb_tunnel_check_pmtu(struct sk_buff *skb, struct dst_entry *encap_dst,
 			  int headroom, bool reply);
 
+static inline void ip_tunnel_adj_headroom(struct net_device *dev,
+					  unsigned int headroom)
+{
+	/* we must cap headroom to some upperlimit, else pskb_expand_head
+	 * will overflow header offsets in skb_headers_offset_update().
+	 */
+	const unsigned int max_allowed = 512;
+
+	if (headroom > max_allowed)
+		headroom = max_allowed;
+
+	if (headroom > READ_ONCE(dev->needed_headroom))
+		WRITE_ONCE(dev->needed_headroom, headroom);
+}
+
 int iptunnel_handle_offloads(struct sk_buff *skb, int gso_type_mask);
 
 static inline int iptunnel_pull_offloads(struct sk_buff *skb)
net/ipv4/ip_tunnel.c +0 -14
index cf9184928eded..6a85200002969 100644
@@ -553,20 +553,6 @@ static int tnl_update_pmtu(struct net_device *dev, struct sk_buff *skb,
 	return 0;
 }
 
-static void ip_tunnel_adj_headroom(struct net_device *dev, unsigned int headroom)
-{
-	/* we must cap headroom to some upperlimit, else pskb_expand_head
-	 * will overflow header offsets in skb_headers_offset_update().
-	 */
-	static const unsigned int max_allowed = 512;
-
-	if (headroom > max_allowed)
-		headroom = max_allowed;
-
-	if (headroom > READ_ONCE(dev->needed_headroom))
-		WRITE_ONCE(dev->needed_headroom, headroom);
-}
-
 void ip_md_tunnel_xmit(struct sk_buff *skb, struct net_device *dev,
 		       u8 proto, int tunnel_hlen)
 {
net/ipv6/ip6_tunnel.c +1 -2
index bd27204725ed8..6efad8d6653b6 100644
@@ -1277,8 +1277,7 @@ int ip6_tnl_xmit(struct sk_buff *skb, struct net_device *dev, __u8 dsfield,
 	 */
 	max_headroom = LL_RESERVED_SPACE(dst->dev) + sizeof(struct ipv6hdr)
 			+ dst->header_len + t->hlen;
-	if (max_headroom > READ_ONCE(dev->needed_headroom))
-		WRITE_ONCE(dev->needed_headroom, max_headroom);
+	ip_tunnel_adj_headroom(dev, max_headroom);
 
 	err = ip6_tnl_encap(skb, t, &proto, fl6);
 	if (err)
Signature · 1 line
2.51.0
author maintainer
#250 lore raw

PATCH 244/332 amd-xgbe: Avoid spurious link down messages during interface toggle

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Raju Rangoju <[email protected]>

[ Upstream commit 2616222e423398bb374ffcb5d23dea4ba2c3e524 ]

During interface toggle operations (ifdown/ifup), the driver currently resets the local helper variable 'phy_link' to -1. This causes the link state machine to incorrectly interpret the state as a link change event, resulting in spurious "Link is down" messages being logged when the interface is brought back up.

Preserve the phy_link state across interface toggles to avoid treating the -1 sentinel value as a legitimate link state transition.

Fixes 88131a812b16 ("amd-xgbe: Perform phy connect/disconnect at dev open/stop")
---
 drivers/net/ethernet/amd/xgbe/xgbe-drv.c  | 1 -
 drivers/net/ethernet/amd/xgbe/xgbe-mdio.c | 1 +
 2 files changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/amd/xgbe/xgbe-drv.c +0 -1
index 8926011604e39..9cd6dac033630 100644
@@ -1172,7 +1172,6 @@ static void xgbe_free_rx_data(struct xgbe_prv_data *pdata)
 
 static int xgbe_phy_reset(struct xgbe_prv_data *pdata)
 {
-	pdata->phy_link = -1;
 	pdata->phy_speed = SPEED_UNKNOWN;
 
 	return pdata->phy_if.phy_reset(pdata);
drivers/net/ethernet/amd/xgbe/xgbe-mdio.c +1 -0
index 19fed56b6ee3f..ebb8b3e5b9a88 100644
@@ -1636,6 +1636,7 @@ static int xgbe_phy_init(struct xgbe_prv_data *pdata)
 		pdata->phy.duplex = DUPLEX_FULL;
 	}
 
+	pdata->phy_link = 0;
 	pdata->phy.link = 0;
 
 	pdata->phy.pause_autoneg = pdata->pause_autoneg;
Signature · 1 line
2.51.0
author maintainer
#251 lore raw

PATCH 245/332 tcp: fix tcp_tso_should_defer() vs large RTT

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Eric Dumazet <[email protected]>

[ Upstream commit 295ce1eb36ae47dc862d6c8a1012618a25516208 ]

Neal reported that using neper tcp_stream with TCP_TX_DELAY set to 50ms would often lead to flows stuck in a small cwnd mode, regardless of the congestion control.

While tcp_stream sets TCP_TX_DELAY too late after the connect(), it highlighted two kernel bugs.

The following heuristic in tcp_tso_should_defer() seems wrong for large RTT:

delta = tp->tcp_clock_cache - head->tstamp;
/* If next ACK is likely to come too late (half srtt), do not defer */ if ((s64)(delta - (u64)NSEC_PER_USEC * (tp->srtt_us >> 4)) < 0)

      goto send_now;

If next ACK is expected to come in more than 1 ms, we should not defer because we prefer a smooth ACK clocking.

While blamed commit was a step in the good direction, it was not generic enough.

Another patch fixing TCP_TX_DELAY for established flows will be proposed when net-next reopens.

---
 net/ipv4/tcp_output.c | 19 +++++++++++++++----
 1 file changed, 15 insertions(+), 4 deletions(-)
net/ipv4/tcp_output.c +15 -4
index 32e38ac5ee2bd..88e8d6543948e 100644
@@ -2177,7 +2177,8 @@ static bool tcp_tso_should_defer(struct sock *sk, struct sk_buff *skb,
 				 u32 max_segs)
 {
 	const struct inet_connection_sock *icsk = inet_csk(sk);
-	u32 send_win, cong_win, limit, in_flight;
+	u32 send_win, cong_win, limit, in_flight, threshold;
+	u64 srtt_in_ns, expected_ack, how_far_is_the_ack;
 	struct tcp_sock *tp = tcp_sk(sk);
 	struct sk_buff *head;
 	int win_divisor;
@@ -2239,9 +2240,19 @@ static bool tcp_tso_should_defer(struct sock *sk, struct sk_buff *skb,
 	head = tcp_rtx_queue_head(sk);
 	if (!head)
 		goto send_now;
-	delta = tp->tcp_clock_cache - head->tstamp;
-	/* If next ACK is likely to come too late (half srtt), do not defer */
-	if ((s64)(delta - (u64)NSEC_PER_USEC * (tp->srtt_us >> 4)) < 0)
+
+	srtt_in_ns = (u64)(NSEC_PER_USEC >> 3) * tp->srtt_us;
+	/* When is the ACK expected ? */
+	expected_ack = head->tstamp + srtt_in_ns;
+	/* How far from now is the ACK expected ? */
+	how_far_is_the_ack = expected_ack - tp->tcp_clock_cache;
+
+	/* If next ACK is likely to come too late,
+	 * ie in more than min(1ms, half srtt), do not defer.
+	 */
+	threshold = min(srtt_in_ns >> 1, NSEC_PER_MSEC);
+
+	if ((s64)(how_far_is_the_ack - threshold) > 0)
 		goto send_now;
 
 	/* Ok, it looks like it is advisable to defer.
Signature · 1 line
2.51.0
author maintainer
#252 lore raw

PATCH 246/332 tg3: prevent use of uninitialized remote_adv and local_adv variables

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alexey Simakov <[email protected]>

[ Upstream commit 0c3f2e62815a43628e748b1e4ad97a1c46cce703 ]

Some execution paths that jump to the fiber_setup_done label could leave the remote_adv and local_adv variables uninitialized and then use it.

Initialize this variables at the point of definition to avoid this.

---
 drivers/net/ethernet/broadcom/tg3.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)
drivers/net/ethernet/broadcom/tg3.c +1 -4
index a7e8f13bb9761..e8be9e5a244fd 100644
@@ -5821,7 +5821,7 @@ static int tg3_setup_fiber_mii_phy(struct tg3 *tp, bool force_reset)
 	u32 current_speed = SPEED_UNKNOWN;
 	u8 current_duplex = DUPLEX_UNKNOWN;
 	bool current_link_up = false;
-	u32 local_adv, remote_adv, sgsr;
+	u32 local_adv = 0, remote_adv = 0, sgsr;
 
 	if ((tg3_asic_rev(tp) == ASIC_REV_5719 ||
 	     tg3_asic_rev(tp) == ASIC_REV_5720) &&
@@ -5962,9 +5962,6 @@ static int tg3_setup_fiber_mii_phy(struct tg3 *tp, bool force_reset)
 		else
 			current_duplex = DUPLEX_HALF;
 
-		local_adv = 0;
-		remote_adv = 0;
-
 		if (bmcr & BMCR_ANENABLE) {
 			u32 common;
 
Signature · 1 line
2.51.0
author maintainer
#253 lore raw

PATCH 247/332 tls: always set record_type in tls_process_cmsg

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Sabrina Dubroca <[email protected]>

[ Upstream commit b6fe4c29bb51cf239ecf48eacf72b924565cb619 ]

When userspace wants to send a non-DATA record (via the TLS_SET_RECORD_TYPE cmsg), we need to send any pending data from a previous MSG_MORE send() as a separate DATA record. If that DATA record is encrypted asynchronously, tls_handle_open_record will return -EINPROGRESS. This is currently treated as an error by tls_process_cmsg, and it will skip setting record_type to the correct value, but the caller (tls_sw_sendmsg_locked) handles that return value correctly and proceeds with sending the new message with an incorrect record_type (DATA instead of whatever was requested in the cmsg).

Always set record_type before handling the open record. If tls_handle_open_record returns an error, record_type will be ignored. If it succeeds, whether with synchronous crypto (returning 0) or asynchronous (returning -EINPROGRESS), the caller will proceed correctly.

---
 net/tls/tls_main.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)
net/tls/tls_main.c +2 -5
index 63517995c692a..f22b32b4c8022 100644
@@ -185,12 +185,9 @@ int tls_proccess_cmsg(struct sock *sk, struct msghdr *msg,
 			if (msg->msg_flags & MSG_MORE)
 				return -EINVAL;
 
-			rc = tls_handle_open_record(sk, msg->msg_flags);
-			if (rc)
-				return rc;
-
 			*record_type = *(unsigned char *)CMSG_DATA(cmsg);
-			rc = 0;
+
+			rc = tls_handle_open_record(sk, msg->msg_flags);
 			break;
 		default:
 			return -EINVAL;
Signature · 1 line
2.51.0
author maintainer
#254 lore raw

PATCH 248/332 tls: dont rely on tx_work during send()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Sabrina Dubroca <[email protected]>

[ Upstream commit 7f846c65ca11e63d2409868ff039081f80e42ae4 ]

With async crypto, we rely on tx_work to actually transmit records once encryption completes. But while send() is running, both the tx_lock and socket lock are held, so tx_work_handler cannot process the queue of encrypted records, and simply reschedules itself. During a large send(), this could last a long time, and use a lot of memory.

Transmit any pending encrypted records before restarting the main loop of tls_sw_sendmsg_locked.

---
 net/tls/tls_sw.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)
net/tls/tls_sw.c +13 -0
index e519a0160668e..a300d1ac13a88 100644
@@ -1056,6 +1056,13 @@ int tls_sw_sendmsg(struct sock *sk, struct msghdr *msg, size_t size)
 				else if (ret != -EAGAIN)
 					goto send_end;
 			}
+
+			/* Transmit if any encryptions have completed */
+			if (test_and_clear_bit(BIT_TX_SCHEDULED, &ctx->tx_bitmask)) {
+				cancel_delayed_work(&ctx->tx_work.work);
+				tls_tx_records(sk, msg->msg_flags);
+			}
+
 			continue;
 rollback_iter:
 			copied -= try_to_copy;
@@ -1110,6 +1117,12 @@ int tls_sw_sendmsg(struct sock *sk, struct msghdr *msg, size_t size)
 					goto send_end;
 				}
 			}
+
+			/* Transmit if any encryptions have completed */
+			if (test_and_clear_bit(BIT_TX_SCHEDULED, &ctx->tx_bitmask)) {
+				cancel_delayed_work(&ctx->tx_work.work);
+				tls_tx_records(sk, msg->msg_flags);
+			}
 		}
 
 		continue;
Signature · 1 line
2.51.0
author maintainer
#255 lore raw

PATCH 249/332 net: usb: use eth_hw_addr_set() instead of ether_addr_copy()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Jakub Kicinski <[email protected]>

[ Upstream commit af804e6db9f60b923ff5149d9bf782e0baa82a2b ]

Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers.

Convert net/usb from ether_addr_copy() to eth_hw_addr_set():

@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)

Stable-dep-of: 8d93ff40d49d ("net: usb: lan78xx: fix use of improperly initialized dev->chipid in lan78xx_reset")

---
 drivers/net/usb/aqc111.c     | 2 +-
 drivers/net/usb/lan78xx.c    | 4 ++--
 drivers/net/usb/r8152.c      | 2 +-
 drivers/net/usb/rndis_host.c | 2 +-
 drivers/net/usb/rtl8150.c    | 2 +-
 5 files changed, 6 insertions(+), 6 deletions(-)
drivers/net/usb/aqc111.c +1 -1
index 485959771431d..ab9431ea295ad 100644
@@ -720,7 +720,7 @@ static int aqc111_bind(struct usbnet *dev, struct usb_interface *intf)
 	if (ret)
 		goto out;
 
-	ether_addr_copy(dev->net->dev_addr, dev->net->perm_addr);
+	eth_hw_addr_set(dev->net, dev->net->perm_addr);
 
 	/* Set Rx urb size */
 	dev->rx_urb_size = URB_SIZE;
drivers/net/usb/lan78xx.c +2 -2
index cabe6cdd6903a..3e3c67dc6bf74 100644
@@ -1756,7 +1756,7 @@ static void lan78xx_init_mac_address(struct lan78xx_net *dev)
 	lan78xx_write_reg(dev, MAF_LO(0), addr_lo);
 	lan78xx_write_reg(dev, MAF_HI(0), addr_hi | MAF_HI_VALID_);
 
-	ether_addr_copy(dev->net->dev_addr, addr);
+	eth_hw_addr_set(dev->net, addr);
 }
 
 /* MDIO read and write wrappers for phylib */
@@ -2331,7 +2331,7 @@ static int lan78xx_set_mac_addr(struct net_device *netdev, void *p)
 	if (!is_valid_ether_addr(addr->sa_data))
 		return -EADDRNOTAVAIL;
 
-	ether_addr_copy(netdev->dev_addr, addr->sa_data);
+	eth_hw_addr_set(netdev, addr->sa_data);
 
 	addr_lo = netdev->dev_addr[0] |
 		  netdev->dev_addr[1] << 8 |
drivers/net/usb/r8152.c +1 -1
index 0d6f10c9bb139..57565fb2c0a11 100644
@@ -1545,7 +1545,7 @@ static int set_ethernet_addr(struct r8152 *tp)
 		return ret;
 
 	if (tp->version == RTL_VER_01)
-		ether_addr_copy(dev->dev_addr, sa.sa_data);
+		eth_hw_addr_set(dev, sa.sa_data);
 	else
 		ret = rtl8152_set_mac_address(dev, &sa);
 
drivers/net/usb/rndis_host.c +1 -1
index 1ff723e15d523..a244796fcaa44 100644
@@ -422,7 +422,7 @@ generic_rndis_bind(struct usbnet *dev, struct usb_interface *intf, int flags)
 	if (bp[0] & 0x02)
 		eth_hw_addr_random(net);
 	else
-		ether_addr_copy(net->dev_addr, bp);
+		eth_hw_addr_set(net, bp);
 
 	/* set a nonzero filter to enable data transfers */
 	memset(u.set, 0, sizeof *u.set);
drivers/net/usb/rtl8150.c +1 -1
index c0f5e8ab1e34e..84252487ae49a 100644
@@ -270,7 +270,7 @@ static void set_ethernet_addr(rtl8150_t *dev)
 	ret = get_registers(dev, IDR, sizeof(node_id), node_id);
 
 	if (!ret) {
-		ether_addr_copy(dev->netdev->dev_addr, node_id);
+		eth_hw_addr_set(dev->netdev, node_id);
 	} else {
 		eth_hw_addr_random(dev->netdev);
 		netdev_notice(dev->netdev, "Assigned a random MAC address: %pM\n",
Signature · 1 line
2.51.0
author maintainer
#256 lore raw

PATCH 250/332 net: usb: lan78xx: Add error handling to lan78xx_init_mac_address

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Oleksij Rempel <[email protected]>

[ Upstream commit 6f31135894ec96481e2bda93a1da70712f5e57c1 ]

Convert lan78xx_init_mac_address to return error codes and handle failures in register read and write operations. Update lan78xx_reset to check for errors during MAC address initialization and propagate them appropriately.

Stable-dep-of: 8d93ff40d49d ("net: usb: lan78xx: fix use of improperly initialized dev->chipid in lan78xx_reset")

---
 drivers/net/usb/lan78xx.c | 36 ++++++++++++++++++++++++++++--------
 1 file changed, 28 insertions(+), 8 deletions(-)
drivers/net/usb/lan78xx.c +28 -8
index 3e3c67dc6bf74..c3aa3f75ab914 100644
@@ -1710,13 +1710,19 @@ static const struct ethtool_ops lan78xx_ethtool_ops = {
 	.get_regs	= lan78xx_get_regs,
 };
 
-static void lan78xx_init_mac_address(struct lan78xx_net *dev)
+static int lan78xx_init_mac_address(struct lan78xx_net *dev)
 {
 	u32 addr_lo, addr_hi;
 	u8 addr[6];
+	int ret;
+
+	ret = lan78xx_read_reg(dev, RX_ADDRL, &addr_lo);
+	if (ret < 0)
+		return ret;
 
-	lan78xx_read_reg(dev, RX_ADDRL, &addr_lo);
-	lan78xx_read_reg(dev, RX_ADDRH, &addr_hi);
+	ret = lan78xx_read_reg(dev, RX_ADDRH, &addr_hi);
+	if (ret < 0)
+		return ret;
 
 	addr[0] = addr_lo & 0xFF;
 	addr[1] = (addr_lo >> 8) & 0xFF;
@@ -1749,14 +1755,26 @@ static void lan78xx_init_mac_address(struct lan78xx_net *dev)
 			  (addr[2] << 16) | (addr[3] << 24);
 		addr_hi = addr[4] | (addr[5] << 8);
 
-		lan78xx_write_reg(dev, RX_ADDRL, addr_lo);
-		lan78xx_write_reg(dev, RX_ADDRH, addr_hi);
+		ret = lan78xx_write_reg(dev, RX_ADDRL, addr_lo);
+		if (ret < 0)
+			return ret;
+
+		ret = lan78xx_write_reg(dev, RX_ADDRH, addr_hi);
+		if (ret < 0)
+			return ret;
 	}
 
-	lan78xx_write_reg(dev, MAF_LO(0), addr_lo);
-	lan78xx_write_reg(dev, MAF_HI(0), addr_hi | MAF_HI_VALID_);
+	ret = lan78xx_write_reg(dev, MAF_LO(0), addr_lo);
+	if (ret < 0)
+		return ret;
+
+	ret = lan78xx_write_reg(dev, MAF_HI(0), addr_hi | MAF_HI_VALID_);
+	if (ret < 0)
+		return ret;
 
 	eth_hw_addr_set(dev->net, addr);
+
+	return 0;
 }
 
 /* MDIO read and write wrappers for phylib */
@@ -2655,7 +2673,9 @@ static int lan78xx_reset(struct lan78xx_net *dev)
 		}
 	} while (buf & HW_CFG_LRST_);
 
-	lan78xx_init_mac_address(dev);
+	ret = lan78xx_init_mac_address(dev);
+	if (ret < 0)
+		return ret;
 
 	/* save DEVID for later usage */
 	ret = lan78xx_read_reg(dev, ID_REV, &buf);
Signature · 1 line
2.51.0
author maintainer
#257 lore raw

PATCH 251/332 net: usb: lan78xx: fix use of improperly initialized dev->chipid in lan78xx_reset

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: I Viswanath <[email protected]>

[ Upstream commit 8d93ff40d49d70e05c82a74beae31f883fe0eaf8 ]

dev->chipid is used in lan78xx_init_mac_address before it's initialized:

lan78xx_reset() {
    lan78xx_init_mac_address()
        lan78xx_read_eeprom()
            lan78xx_read_raw_eeprom() <- dev->chipid is used here

    dev->chipid = ... <- dev->chipid is initialized correctly here
}

Reorder initialization so that dev->chipid is set before calling lan78xx_init_mac_address().

---
 drivers/net/usb/lan78xx.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/net/usb/lan78xx.c +4 -4
index c3aa3f75ab914..fd5fa64cbe932 100644
@@ -2673,10 +2673,6 @@ static int lan78xx_reset(struct lan78xx_net *dev)
 		}
 	} while (buf & HW_CFG_LRST_);
 
-	ret = lan78xx_init_mac_address(dev);
-	if (ret < 0)
-		return ret;
-
 	/* save DEVID for later usage */
 	ret = lan78xx_read_reg(dev, ID_REV, &buf);
 	if (ret < 0)
@@ -2685,6 +2681,10 @@ static int lan78xx_reset(struct lan78xx_net *dev)
 	dev->chipid = (buf & ID_REV_CHIP_ID_MASK_) >> 16;
 	dev->chiprev = buf & ID_REV_CHIP_REV_MASK_;
 
+	ret = lan78xx_init_mac_address(dev);
+	if (ret < 0)
+		return ret;
+
 	/* Respond to the IN token with a NAK */
 	ret = lan78xx_read_reg(dev, USB_CFG0, &buf);
 	if (ret < 0)
Signature · 1 line
2.51.0
author maintainer
#258 lore raw

PATCH 252/332 drm/amd/powerplay: Fix CIK shutdown temperature

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Timur Kristóf <[email protected]>

[ Upstream commit 6917112af2ba36c5f19075eb9f2933ffd07e55bf ]

Remove extra multiplication.

CIK GPUs such as Hawaii appear to use PP_TABLE_V0 in which case the shutdown temperature is hardcoded in smu7_init_dpm_defaults and is already multiplied by 1000. The value was mistakenly multiplied another time by smu7_get_thermal_temperature_range.

Fixes 4ba082572a42 ("drm/amd/powerplay: export the thermal ranges of VI asics (V2)")
---
 drivers/gpu/drm/amd/pm/powerplay/hwmgr/smu7_hwmgr.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/gpu/drm/amd/pm/powerplay/hwmgr/smu7_hwmgr.c +1 -2
index 3673a9e7ba449..e2816c88cfe52 100644
@@ -4982,8 +4982,7 @@ static int smu7_get_thermal_temperature_range(struct pp_hwmgr *hwmgr,
 		thermal_data->max = table_info->cac_dtp_table->usSoftwareShutdownTemp *
 			PP_TEMPERATURE_UNITS_PER_CENTIGRADES;
 	else if (hwmgr->pp_table_version == PP_TABLE_V0)
-		thermal_data->max = data->thermal_temp_setting.temperature_shutdown *
-			PP_TEMPERATURE_UNITS_PER_CENTIGRADES;
+		thermal_data->max = data->thermal_temp_setting.temperature_shutdown;
 
 	return 0;
 }
Signature · 1 line
2.51.0
author maintainer
#259 lore raw

PATCH 253/332 sched/fair: Trivial correction of the newidle_balance() comment

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Barry Song <[email protected]>

[ Upstream commit 5b78f2dc315354c05300795064f587366a02c6ff ]

idle_balance() has been renamed to newidle_balance(). To differentiate with nohz_idle_balance, it seems refining the comment will be helpful for the readers of the code.

Stable-dep-of: 17e3e88ed0b6 ("sched/fair: Fix pelt lost idle time detection")

---
 kernel/sched/fair.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/sched/fair.c +1 -1
index 9f8cb265589b3..802c97a05f57e 100644
@@ -10808,7 +10808,7 @@ static inline void nohz_newidle_balance(struct rq *this_rq) { }
 #endif /* CONFIG_NO_HZ_COMMON */
 
 /*
- * idle_balance is called by schedule() if this_cpu is about to become
+ * newidle_balance is called by schedule() if this_cpu is about to become
  * idle. Attempts to pull tasks from other CPUs.
  *
  * Returns:
Signature · 1 line
2.51.0
author maintainer
#260 lore raw

PATCH 254/332 sched/balancing: Rename newidle_balance() => sched_balance_newidle()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Ingo Molnar <[email protected]>

[ Upstream commit 7d058285cd77cc1411c91efd1b1673530bb1bee8 ]

Standardize scheduler load-balancing function names on the sched_balance_() prefix.

Stable-dep-of: 17e3e88ed0b6 ("sched/fair: Fix pelt lost idle time detection")

---
 kernel/sched/fair.c | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)
kernel/sched/fair.c +8 -8
index 802c97a05f57e..952a3fd41a6fe 100644
@@ -3907,7 +3907,7 @@ static inline unsigned long cfs_rq_load_avg(struct cfs_rq *cfs_rq)
 	return cfs_rq->avg.load_avg;
 }
 
-static int newidle_balance(struct rq *this_rq, struct rq_flags *rf);
+static int sched_balance_newidle(struct rq *this_rq, struct rq_flags *rf);
 
 static inline unsigned long task_util(struct task_struct *p)
 {
@@ -4234,7 +4234,7 @@ attach_entity_load_avg(struct cfs_rq *cfs_rq, struct sched_entity *se) {}
 static inline void
 detach_entity_load_avg(struct cfs_rq *cfs_rq, struct sched_entity *se) {}
 
-static inline int newidle_balance(struct rq *rq, struct rq_flags *rf)
+static inline int sched_balance_newidle(struct rq *rq, struct rq_flags *rf)
 {
 	return 0;
 }
@@ -7065,7 +7065,7 @@ balance_fair(struct rq *rq, struct task_struct *prev, struct rq_flags *rf)
 	if (rq->nr_running)
 		return 1;
 
-	return newidle_balance(rq, rf) != 0;
+	return sched_balance_newidle(rq, rf) != 0;
 }
 #endif /* CONFIG_SMP */
 
@@ -7356,10 +7356,10 @@ done: __maybe_unused;
 	if (!rf)
 		return NULL;
 
-	new_tasks = newidle_balance(rq, rf);
+	new_tasks = sched_balance_newidle(rq, rf);
 
 	/*
-	 * Because newidle_balance() releases (and re-acquires) rq->lock, it is
+	 * Because sched_balance_newidle() releases (and re-acquires) rq->lock, it is
 	 * possible for any higher priority task to appear. In that case we
 	 * must re-start the pick_next_entity() loop.
 	 */
@@ -10090,7 +10090,7 @@ static int load_balance(int this_cpu, struct rq *this_rq,
 	ld_moved = 0;
 
 	/*
-	 * newidle_balance() disregards balance intervals, so we could
+	 * sched_balance_newidle() disregards balance intervals, so we could
 	 * repeatedly reach this code, which would lead to balance_interval
 	 * skyrocketting in a short amount of time. Skip the balance_interval
 	 * increase logic to avoid that.
@@ -10808,7 +10808,7 @@ static inline void nohz_newidle_balance(struct rq *this_rq) { }
 #endif /* CONFIG_NO_HZ_COMMON */
 
 /*
- * newidle_balance is called by schedule() if this_cpu is about to become
+ * sched_balance_newidle is called by schedule() if this_cpu is about to become
  * idle. Attempts to pull tasks from other CPUs.
  *
  * Returns:
@@ -10816,7 +10816,7 @@ static inline void nohz_newidle_balance(struct rq *this_rq) { }
  *     0 - failed, no new tasks
  *   > 0 - success, new (fair) tasks present
  */
-static int newidle_balance(struct rq *this_rq, struct rq_flags *rf)
+static int sched_balance_newidle(struct rq *this_rq, struct rq_flags *rf)
 {
 	unsigned long next_balance = jiffies + HZ;
 	int this_cpu = this_rq->cpu;
Signature · 1 line
2.51.0
author maintainer
#261 lore raw

PATCH 255/332 sched/fair: Fix pelt lost idle time detection

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Vincent Guittot <[email protected]>

[ Upstream commit 17e3e88ed0b6318fde0d1c14df1a804711cab1b5 ]

The check for some lost idle pelt time should be always done when pick_next_task_fair() fails to pick a task and not only when we call it from the fair fast-path.

The case happens when the last running task on rq is a RT or DL task. When the latter goes to sleep and the /Sum of util_sum of the rq is at the max value, we don't account the lost of idle time whereas we should.

Fixes 67692435c411 ("sched: Rework pick_next_task() slow-path")
---
 kernel/sched/fair.c | 26 +++++++++++++-------------
 1 file changed, 13 insertions(+), 13 deletions(-)
kernel/sched/fair.c +13 -13
index 952a3fd41a6fe..c11d59bea0ea8 100644
@@ -7353,21 +7353,21 @@ done: __maybe_unused;
 	return p;
 
 idle:
-	if (!rf)
-		return NULL;
-
-	new_tasks = sched_balance_newidle(rq, rf);
+	if (rf) {
+		new_tasks = sched_balance_newidle(rq, rf);
 
-	/*
-	 * Because sched_balance_newidle() releases (and re-acquires) rq->lock, it is
-	 * possible for any higher priority task to appear. In that case we
-	 * must re-start the pick_next_entity() loop.
-	 */
-	if (new_tasks < 0)
-		return RETRY_TASK;
+		/*
+		 * Because sched_balance_newidle() releases (and re-acquires)
+		 * rq->lock, it is possible for any higher priority task to
+		 * appear. In that case we must re-start the pick_next_entity()
+		 * loop.
+		 */
+		if (new_tasks < 0)
+			return RETRY_TASK;
 
-	if (new_tasks > 0)
-		goto again;
+		if (new_tasks > 0)
+			goto again;
+	}
 
 	/*
 	 * rq is about to be idle, check if we need to update the
Signature · 1 line
2.51.0
author maintainer
#262 lore raw

PATCH 256/332 ALSA: firewire: amdtp-stream: fix enum kernel-doc warnings

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Randy Dunlap <[email protected]>

[ Upstream commit d41f68dff783d181a8fd462e612bda0fbab7f735 ]

Fix spelling of CIP_NO_HEADER to prevent a kernel-doc warning.

Warning: amdtp-stream.h:57 Enum value 'CIP_NO_HEADER' not described in enum 'cip_flags'
Warning: amdtp-stream.h:57 Excess enum value '%CIP_NO_HEADERS' description in 'cip_flags'

Fixes 3b196c394dd9f ("ALSA: firewire-lib: add no-header packet processing")
---
 sound/firewire/amdtp-stream.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
sound/firewire/amdtp-stream.h +1 -1
index 2ceb57d1d58ee..1332089683da0 100644
@@ -32,7 +32,7 @@
  *	allows 5 times as large as IEC 61883-6 defines.
  * @CIP_HEADER_WITHOUT_EOH: Only for in-stream. CIP Header doesn't include
  *	valid EOH.
- * @CIP_NO_HEADERS: a lack of headers in packets
+ * @CIP_NO_HEADER: a lack of headers in packets
  * @CIP_UNALIGHED_DBC: Only for in-stream. The value of dbc is not alighed to
  *	the value of current SYT_INTERVAL; e.g. initial value is not zero.
  */
Signature · 1 line
2.51.0
author maintainer
#263 lore raw

PATCH 257/332 hfsplus: fix slab-out-of-bounds read in hfsplus_strcasecmp()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Viacheslav Dubeyko <[email protected]>

commit 42520df65bf67189541a425f7d36b0b3e7bd7844 upstream.

The hfsplus_strcasecmp() logic can trigger the issue:

[  117.317703][ T9855] ==================================================================
[  117.318353][ T9855] BUG: KASAN: slab-out-of-bounds in hfsplus_strcasecmp+0x1bc/0x490
[  117.318991][ T9855] Read of size 2 at addr ffff88802160f40c by task repro/9855
[  117.319577][ T9855]
[  117.319773][ T9855] CPU: 0 UID: 0 PID: 9855 Comm: repro Not tainted 6.17.0-rc6 #33 PREEMPT(full)
[  117.319780][ T9855] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[  117.319783][ T9855] Call Trace:
[  117.319785][ T9855]  <TASK>
[  117.319788][ T9855]  dump_stack_lvl+0x1c1/0x2a0
[  117.319795][ T9855]  ? __virt_addr_valid+0x1c8/0x5c0
[  117.319803][ T9855]  ? __pfx_dump_stack_lvl+0x10/0x10
[  117.319808][ T9855]  ? rcu_is_watching+0x15/0xb0
[  117.319816][ T9855]  ? lock_release+0x4b/0x3e0
[  117.319821][ T9855]  ? __kasan_check_byte+0x12/0x40
[  117.319828][ T9855]  ? __virt_addr_valid+0x1c8/0x5c0
[  117.319835][ T9855]  ? __virt_addr_valid+0x4a5/0x5c0
[  117.319842][ T9855]  print_report+0x17e/0x7e0
[  117.319848][ T9855]  ? __virt_addr_valid+0x1c8/0x5c0
[  117.319855][ T9855]  ? __virt_addr_valid+0x4a5/0x5c0
[  117.319862][ T9855]  ? __phys_addr+0xd3/0x180
[  117.319869][ T9855]  ? hfsplus_strcasecmp+0x1bc/0x490
[  117.319876][ T9855]  kasan_report+0x147/0x180
[  117.319882][ T9855]  ? hfsplus_strcasecmp+0x1bc/0x490
[  117.319891][ T9855]  hfsplus_strcasecmp+0x1bc/0x490
[  117.319900][ T9855]  ? __pfx_hfsplus_cat_case_cmp_key+0x10/0x10
[  117.319906][ T9855]  hfs_find_rec_by_key+0xa9/0x1e0
[  117.319913][ T9855]  __hfsplus_brec_find+0x18e/0x470
[  117.319920][ T9855]  ? __pfx_hfsplus_bnode_find+0x10/0x10
[  117.319926][ T9855]  ? __pfx_hfs_find_rec_by_key+0x10/0x10
[  117.319933][ T9855]  ? __pfx___hfsplus_brec_find+0x10/0x10
[  117.319942][ T9855]  hfsplus_brec_find+0x28f/0x510
[  117.319949][ T9855]  ? __pfx_hfs_find_rec_by_key+0x10/0x10
[  117.319956][ T9855]  ? __pfx_hfsplus_brec_find+0x10/0x10
[  117.319963][ T9855]  ? __kmalloc_noprof+0x2a9/0x510
[  117.319969][ T9855]  ? hfsplus_find_init+0x8c/0x1d0
[  117.319976][ T9855]  hfsplus_brec_read+0x2b/0x120
[  117.319983][ T9855]  hfsplus_lookup+0x2aa/0x890
[  117.319990][ T9855]  ? __pfx_hfsplus_lookup+0x10/0x10
[  117.320003][ T9855]  ? d_alloc_parallel+0x2f0/0x15e0
[  117.320008][ T9855]  ? __lock_acquire+0xaec/0xd80
[  117.320013][ T9855]  ? __pfx_d_alloc_parallel+0x10/0x10
[  117.320019][ T9855]  ? __raw_spin_lock_init+0x45/0x100
[  117.320026][ T9855]  ? __init_waitqueue_head+0xa9/0x150
[  117.320034][ T9855]  __lookup_slow+0x297/0x3d0
[  117.320039][ T9855]  ? __pfx___lookup_slow+0x10/0x10
[  117.320045][ T9855]  ? down_read+0x1ad/0x2e0
[  117.320055][ T9855]  lookup_slow+0x53/0x70
[  117.320065][ T9855]  walk_component+0x2f0/0x430
[  117.320073][ T9855]  path_lookupat+0x169/0x440
[  117.320081][ T9855]  filename_lookup+0x212/0x590
[  117.320089][ T9855]  ? __pfx_filename_lookup+0x10/0x10
[  117.320098][ T9855]  ? strncpy_from_user+0x150/0x290
[  117.320105][ T9855]  ? getname_flags+0x1e5/0x540
[  117.320112][ T9855]  user_path_at+0x3a/0x60
[  117.320117][ T9855]  __x64_sys_umount+0xee/0x160
[  117.320123][ T9855]  ? __pfx___x64_sys_umount+0x10/0x10
[  117.320129][ T9855]  ? do_syscall_64+0xb7/0x3a0
[  117.320135][ T9855]  ? entry_SYSCALL_64_after_hwframe+0x77/0x7f
[  117.320141][ T9855]  ? entry_SYSCALL_64_after_hwframe+0x77/0x7f
[  117.320145][ T9855]  do_syscall_64+0xf3/0x3a0
[  117.320150][ T9855]  ? exc_page_fault+0x9f/0xf0
[  117.320154][ T9855]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[  117.320158][ T9855] RIP: 0033:0x7f7dd7908b07
[  117.320163][ T9855] Code: 23 0d 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 31 f6 e9 09 00 00 00 66 0f 1f 84 00 00 08
[  117.320167][ T9855] RSP: 002b:00007ffd5ebd9698 EFLAGS: 00000202 ORIG_RAX: 00000000000000a6
[  117.320172][ T9855] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f7dd7908b07
[  117.320176][ T9855] RDX: 0000000000000009 RSI: 0000000000000009 RDI: 00007ffd5ebd9740
[  117.320179][ T9855] RBP: 00007ffd5ebda780 R08: 0000000000000005 R09: 00007ffd5ebd9530
[  117.320181][ T9855] R10: 00007f7dd799bfc0 R11: 0000000000000202 R12: 000055e2008b32d0
[  117.320184][ T9855] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
[  117.320189][ T9855]  </TASK>
[  117.320190][ T9855]
[  117.351311][ T9855] Allocated by task 9855:
[  117.351683][ T9855]  kasan_save_track+0x3e/0x80
[  117.352093][ T9855]  __kasan_kmalloc+0x8d/0xa0
[  117.352490][ T9855]  __kmalloc_noprof+0x288/0x510
[  117.352914][ T9855]  hfsplus_find_init+0x8c/0x1d0
[  117.353342][ T9855]  hfsplus_lookup+0x19c/0x890
[  117.353747][ T9855]  __lookup_slow+0x297/0x3d0
[  117.354148][ T9855]  lookup_slow+0x53/0x70
[  117.354514][ T9855]  walk_component+0x2f0/0x430
[  117.354921][ T9855]  path_lookupat+0x169/0x440
[  117.355325][ T9855]  filename_lookup+0x212/0x590
[  117.355740][ T9855]  user_path_at+0x3a/0x60
[  117.356115][ T9855]  __x64_sys_umount+0xee/0x160
[  117.356529][ T9855]  do_syscall_64+0xf3/0x3a0
[  117.356920][ T9855]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[  117.357429][ T9855]
[  117.357636][ T9855] The buggy address belongs to the object at ffff88802160f000
[  117.357636][ T9855]  which belongs to the cache kmalloc-2k of size 2048
[  117.358827][ T9855] The buggy address is located 0 bytes to the right of
[  117.358827][ T9855]  allocated 1036-byte region [ffff88802160f000, ffff88802160f40c)
[  117.360061][ T9855]
[  117.360266][ T9855] The buggy address belongs to the physical page:
[  117.360813][ T9855] page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x21608
[  117.361562][ T9855] head: order:3 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
[  117.362285][ T9855] flags: 0xfff00000000040(head|node=0|zone=1|lastcpupid=0x7ff)
[  117.362929][ T9855] page_type: f5(slab)
[  117.363282][ T9855] raw: 00fff00000000040 ffff88801a842f00 ffffea0000932000 dead000000000002
[  117.364015][ T9855] raw: 0000000000000000 0000000080080008 00000000f5000000 0000000000000000
[  117.364750][ T9855] head: 00fff00000000040 ffff88801a842f00 ffffea0000932000 dead000000000002
[  117.365491][ T9855] head: 0000000000000000 0000000080080008 00000000f5000000 0000000000000000
[  117.366232][ T9855] head: 00fff00000000003 ffffea0000858201 00000000ffffffff 00000000ffffffff
[  117.366968][ T9855] head: ffffffffffffffff 0000000000000000 00000000ffffffff 0000000000000008
[  117.367711][ T9855] page dumped because: kasan: bad access detected
[  117.368259][ T9855] page_owner tracks the page as allocated
[  117.368745][ T9855] page last allocated via order 3, migratetype Unmovable, gfp_mask 0xd20c0(__GFP_IO|__GFP_FS|__GFP_NOWARN1
[  117.370541][ T9855]  post_alloc_hook+0x240/0x2a0
[  117.370954][ T9855]  get_page_from_freelist+0x2101/0x21e0
[  117.371435][ T9855]  __alloc_frozen_pages_noprof+0x274/0x380
[  117.371935][ T9855]  alloc_pages_mpol+0x241/0x4b0
[  117.372360][ T9855]  allocate_slab+0x8d/0x380
[  117.372752][ T9855]  ___slab_alloc+0xbe3/0x1400
[  117.373159][ T9855]  __kmalloc_cache_noprof+0x296/0x3d0
[  117.373621][ T9855]  nexthop_net_init+0x75/0x100
[  117.374038][ T9855]  ops_init+0x35c/0x5c0
[  117.374400][ T9855]  setup_net+0x10c/0x320
[  117.374768][ T9855]  copy_net_ns+0x31b/0x4d0
[  117.375156][ T9855]  create_new_namespaces+0x3f3/0x720
[  117.375613][ T9855]  unshare_nsproxy_namespaces+0x11c/0x170
[  117.376094][ T9855]  ksys_unshare+0x4ca/0x8d0
[  117.376477][ T9855]  __x64_sys_unshare+0x38/0x50
[  117.376879][ T9855]  do_syscall_64+0xf3/0x3a0
[  117.377265][ T9855] page last free pid 9110 tgid 9110 stack trace:
[  117.377795][ T9855]  __free_frozen_pages+0xbeb/0xd50
[  117.378229][ T9855]  __put_partials+0x152/0x1a0
[  117.378625][ T9855]  put_cpu_partial+0x17c/0x250
[  117.379026][ T9855]  __slab_free+0x2d4/0x3c0
[  117.379404][ T9855]  qlist_free_all+0x97/0x140
[  117.379790][ T9855]  kasan_quarantine_reduce+0x148/0x160
[  117.380250][ T9855]  __kasan_slab_alloc+0x22/0x80
[  117.380662][ T9855]  __kmalloc_noprof+0x232/0x510
[  117.381074][ T9855]  tomoyo_supervisor+0xc0a/0x1360
[  117.381498][ T9855]  tomoyo_env_perm+0x149/0x1e0
[  117.381903][ T9855]  tomoyo_find_next_domain+0x15ad/0x1b90
[  117.382378][ T9855]  tomoyo_bprm_check_security+0x11c/0x180
[  117.382859][ T9855]  security_bprm_check+0x89/0x280
[  117.383289][ T9855]  bprm_execve+0x8f1/0x14a0
[  117.383673][ T9855]  do_execveat_common+0x528/0x6b0
[  117.384103][ T9855]  __x64_sys_execve+0x94/0xb0
[  117.384500][ T9855]
[  117.384706][ T9855] Memory state around the buggy address:
[  117.385179][ T9855]  ffff88802160f300: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[  117.385854][ T9855]  ffff88802160f380: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[  117.386534][ T9855] >ffff88802160f400: 00 04 fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[  117.387204][ T9855]                       ^
[  117.387566][ T9855]  ffff88802160f480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[  117.388243][ T9855]  ffff88802160f500: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[  117.388918][ T9855] ==================================================================

The issue takes place if the length field of struct hfsplus_unistr is bigger than HFSPLUS_MAX_STRLEN. The patch simply checks the length of comparing strings. And if the strings' length is bigger than HFSPLUS_MAX_STRLEN, then it is corrected to this value.

v2
The string length correction has been added for hfsplus_strcmp().

---
 fs/hfsplus/unicode.c |   24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)
fs/hfsplus/unicode.c +24 -0
@@ -40,6 +40,18 @@ int hfsplus_strcasecmp(const struct hfsp
 	p1 = s1->unicode;
 	p2 = s2->unicode;
 
+	if (len1 > HFSPLUS_MAX_STRLEN) {
+		len1 = HFSPLUS_MAX_STRLEN;
+		pr_err("invalid length %u has been corrected to %d\n",
+			be16_to_cpu(s1->length), len1);
+	}
+
+	if (len2 > HFSPLUS_MAX_STRLEN) {
+		len2 = HFSPLUS_MAX_STRLEN;
+		pr_err("invalid length %u has been corrected to %d\n",
+			be16_to_cpu(s2->length), len2);
+	}
+
 	while (1) {
 		c1 = c2 = 0;
 
@@ -74,6 +86,18 @@ int hfsplus_strcmp(const struct hfsplus_
 	p1 = s1->unicode;
 	p2 = s2->unicode;
 
+	if (len1 > HFSPLUS_MAX_STRLEN) {
+		len1 = HFSPLUS_MAX_STRLEN;
+		pr_err("invalid length %u has been corrected to %d\n",
+			be16_to_cpu(s1->length), len1);
+	}
+
+	if (len2 > HFSPLUS_MAX_STRLEN) {
+		len2 = HFSPLUS_MAX_STRLEN;
+		pr_err("invalid length %u has been corrected to %d\n",
+			be16_to_cpu(s2->length), len2);
+	}
+
 	for (len = min(len1, len2); len > 0; len--) {
 		c1 = be16_to_cpu(*p1);
 		c2 = be16_to_cpu(*p2);
author maintainer
#264 lore raw

PATCH 258/332 exec: Fix incorrect type for ret

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Xichao Zhao <[email protected]>

[ Upstream commit 5e088248375d171b80c643051e77ade6b97bc386 ]

In the setup_arg_pages(), ret is declared as an unsigned long. The ret might take a negative value. Therefore, its type should be changed to int.

---
 fs/exec.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
fs/exec.c +1 -1
index 7144c541818f6..2979b458b650a 100644
@@ -746,7 +746,7 @@ int setup_arg_pages(struct linux_binprm *bprm,
 		    unsigned long stack_top,
 		    int executable_stack)
 {
-	unsigned long ret;
+	int ret;
 	unsigned long stack_shift;
 	struct mm_struct *mm = current->mm;
 	struct vm_area_struct *vma = bprm->vma;
Signature · 1 line
2.51.0
author maintainer
#265 lore raw

PATCH 259/332 hfs: clear offset and space out of valid records in b-tree node

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Viacheslav Dubeyko <[email protected]>

[ Upstream commit 18b07c44f245beb03588b00b212b38fce9af7cc9 ]

Currently, hfs_brec_remove() executes moving records towards the location of deleted record and it updates offsets of moved records. However, the hfs_brec_remove() logic ignores the "mess" of b-tree node's free space and it doesn't touch the offsets out of records number. Potentially, it could confuse fsck or driver logic or to be a reason of potential corruption cases.

This patch reworks the logic of hfs_brec_remove() by means of clearing freed space of b-tree node after the records moving. And it clear the last offset that keeping old location of free space because now the offset before this one is keeping the actual offset to the free space after the record deletion.

---
 fs/hfs/brec.c | 27 +++++++++++++++++++++++----
 1 file changed, 23 insertions(+), 4 deletions(-)
fs/hfs/brec.c +23 -4
index 896396554bcc1..b01db1fae147c 100644
@@ -179,6 +179,7 @@ int hfs_brec_remove(struct hfs_find_data *fd)
 	struct hfs_btree *tree;
 	struct hfs_bnode *node, *parent;
 	int end_off, rec_off, data_off, size;
+	int src, dst, len;
 
 	tree = fd->tree;
 	node = fd->bnode;
@@ -208,10 +209,14 @@ int hfs_brec_remove(struct hfs_find_data *fd)
 	}
 	hfs_bnode_write_u16(node, offsetof(struct hfs_bnode_desc, num_recs), node->num_recs);
 
-	if (rec_off == end_off)
-		goto skip;
 	size = fd->keylength + fd->entrylength;
 
+	if (rec_off == end_off) {
+		src = fd->keyoffset;
+		hfs_bnode_clear(node, src, size);
+		goto skip;
+	}
+
 	do {
 		data_off = hfs_bnode_read_u16(node, rec_off);
 		hfs_bnode_write_u16(node, rec_off + 2, data_off - size);
@@ -219,9 +224,23 @@ int hfs_brec_remove(struct hfs_find_data *fd)
 	} while (rec_off >= end_off);
 
 	/* fill hole */
-	hfs_bnode_move(node, fd->keyoffset, fd->keyoffset + size,
-		       data_off - fd->keyoffset - size);
+	dst = fd->keyoffset;
+	src = fd->keyoffset + size;
+	len = data_off - src;
+
+	hfs_bnode_move(node, dst, src, len);
+
+	src = dst + len;
+	len = data_off - src;
+
+	hfs_bnode_clear(node, src, len);
+
 skip:
+	/*
+	 * Remove the obsolete offset to free space.
+	 */
+	hfs_bnode_write_u16(node, end_off, 0);
+
 	hfs_bnode_dump(node);
 	if (!fd->record)
 		hfs_brec_update_parent(fd);
Signature · 1 line
2.51.0
author maintainer
#266 lore raw

PATCH 260/332 hfs: make proper initalization of struct hfs_find_data

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Viacheslav Dubeyko <[email protected]>

[ Upstream commit c62663a986acee7c4485c1fa9de5fc40194b6290 ]

Potenatially, __hfs_ext_read_extent() could operate by not initialized values of fd->key after hfs_brec_find() call:

static inline int __hfs_ext_read_extent(struct hfs_find_data *fd, struct hfs_extent *extent,

                                        u32 cnid, u32 block, u8 type)
{
        int res;

        hfs_ext_build_key(fd->search_key, cnid, block, type);
        fd->key->ext.FNum = 0;
        res = hfs_brec_find(fd);
        if (res && res != -ENOENT)
                return res;
        if (fd->key->ext.FNum != fd->search_key->ext.FNum ||
            fd->key->ext.FkType != fd->search_key->ext.FkType)
                return -ENOENT;
        if (fd->entrylength != sizeof(hfs_extent_rec))
                return -EIO;
        hfs_bnode_read(fd->bnode, extent, fd->entryoffset, sizeof(hfs_extent_rec));
        return 0;
}

This patch changes kmalloc() on kzalloc() in hfs_find_init() and intializes fd->record, fd->keyoffset, fd->keylength, fd->entryoffset, fd->entrylength for the case if hfs_brec_find() has been found nothing in the b-tree node.

---
 fs/hfs/bfind.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
fs/hfs/bfind.c +7 -1
index ef9498a6e88ac..6d37b4c759034 100644
@@ -18,7 +18,7 @@ int hfs_find_init(struct hfs_btree *tree, struct hfs_find_data *fd)
 
 	fd->tree = tree;
 	fd->bnode = NULL;
-	ptr = kmalloc(tree->max_key_len * 2 + 4, GFP_KERNEL);
+	ptr = kzalloc(tree->max_key_len * 2 + 4, GFP_KERNEL);
 	if (!ptr)
 		return -ENOMEM;
 	fd->search_key = ptr;
@@ -112,6 +112,12 @@ int hfs_brec_find(struct hfs_find_data *fd)
 	__be32 data;
 	int height, res;
 
+	fd->record = -1;
+	fd->keyoffset = -1;
+	fd->keylength = -1;
+	fd->entryoffset = -1;
+	fd->entrylength = -1;
+
 	tree = fd->tree;
 	if (fd->bnode)
 		hfs_bnode_put(fd->bnode);
Signature · 1 line
2.51.0
author maintainer
#267 lore raw

PATCH 261/332 hfsplus: fix KMSAN uninit-value issue in __hfsplus_ext_cache_extent()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Viacheslav Dubeyko <[email protected]>

[ Upstream commit 4840ceadef4290c56cc422f0fc697655f3cbf070 ]

The syzbot reported issue in __hfsplus_ext_cache_extent():

[   70.194323][ T9350] BUG: KMSAN: uninit-value in __hfsplus_ext_cache_extent+0x7d0/0x990
[   70.195022][ T9350]  __hfsplus_ext_cache_extent+0x7d0/0x990
[   70.195530][ T9350]  hfsplus_file_extend+0x74f/0x1cf0
[   70.195998][ T9350]  hfsplus_get_block+0xe16/0x17b0
[   70.196458][ T9350]  __block_write_begin_int+0x962/0x2ce0
[   70.196959][ T9350]  cont_write_begin+0x1000/0x1950
[   70.197416][ T9350]  hfsplus_write_begin+0x85/0x130
[   70.197873][ T9350]  generic_perform_write+0x3e8/0x1060
[   70.198374][ T9350]  __generic_file_write_iter+0x215/0x460
[   70.198892][ T9350]  generic_file_write_iter+0x109/0x5e0
[   70.199393][ T9350]  vfs_write+0xb0f/0x14e0
[   70.199771][ T9350]  ksys_write+0x23e/0x490
[   70.200149][ T9350]  __x64_sys_write+0x97/0xf0
[   70.200570][ T9350]  x64_sys_call+0x3015/0x3cf0
[   70.201065][ T9350]  do_syscall_64+0xd9/0x1d0
[   70.201506][ T9350]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[   70.202054][ T9350]
[   70.202279][ T9350] Uninit was created at:
[   70.202693][ T9350]  __kmalloc_noprof+0x621/0xf80
[   70.203149][ T9350]  hfsplus_find_init+0x8d/0x1d0
[   70.203602][ T9350]  hfsplus_file_extend+0x6ca/0x1cf0
[   70.204087][ T9350]  hfsplus_get_block+0xe16/0x17b0
[   70.204561][ T9350]  __block_write_begin_int+0x962/0x2ce0
[   70.205074][ T9350]  cont_write_begin+0x1000/0x1950
[   70.205547][ T9350]  hfsplus_write_begin+0x85/0x130
[   70.206017][ T9350]  generic_perform_write+0x3e8/0x1060
[   70.206519][ T9350]  __generic_file_write_iter+0x215/0x460
[   70.207042][ T9350]  generic_file_write_iter+0x109/0x5e0
[   70.207552][ T9350]  vfs_write+0xb0f/0x14e0
[   70.207961][ T9350]  ksys_write+0x23e/0x490
[   70.208375][ T9350]  __x64_sys_write+0x97/0xf0
[   70.208810][ T9350]  x64_sys_call+0x3015/0x3cf0
[   70.209255][ T9350]  do_syscall_64+0xd9/0x1d0
[   70.209680][ T9350]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[   70.210230][ T9350]
[   70.210454][ T9350] CPU: 2 UID: 0 PID: 9350 Comm: repro Not tainted 6.12.0-rc5 #5
[   70.211174][ T9350] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[   70.212115][ T9350] =====================================================
[   70.212734][ T9350] Disabling lock debugging due to kernel taint
[   70.213284][ T9350] Kernel panic - not syncing: kmsan.panic set ...
[   70.213858][ T9350] CPU: 2 UID: 0 PID: 9350 Comm: repro Tainted: G    B              6.12.0-rc5 #5
[   70.214679][ T9350] Tainted: [B]=BAD_PAGE
[   70.215057][ T9350] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[   70.215999][ T9350] Call Trace:
[   70.216309][ T9350]  <TASK>
[   70.216585][ T9350]  dump_stack_lvl+0x1fd/0x2b0
[   70.217025][ T9350]  dump_stack+0x1e/0x30
[   70.217421][ T9350]  panic+0x502/0xca0
[   70.217803][ T9350]  ? kmsan_get_metadata+0x13e/0x1c0
[   70.218294][ Message fromT sy9350]  kmsan_report+0x296/slogd@syzkaller 0x2aat Aug 18 22:11:058 ...
 kernel
:[   70.213284][ T9350] Kernel panic - not syncing: kmsan.panic [   70.220179][ T9350]  ? kmsan_get_metadata+0x13e/0x1c0
set ...
[   70.221254][ T9350]  ? __msan_warning+0x96/0x120
[   70.222066][ T9350]  ? __hfsplus_ext_cache_extent+0x7d0/0x990
[   70.223023][ T9350]  ? hfsplus_file_extend+0x74f/0x1cf0
[   70.224120][ T9350]  ? hfsplus_get_block+0xe16/0x17b0
[   70.224946][ T9350]  ? __block_write_begin_int+0x962/0x2ce0
[   70.225756][ T9350]  ? cont_write_begin+0x1000/0x1950
[   70.226337][ T9350]  ? hfsplus_write_begin+0x85/0x130
[   70.226852][ T9350]  ? generic_perform_write+0x3e8/0x1060
[   70.227405][ T9350]  ? __generic_file_write_iter+0x215/0x460
[   70.227979][ T9350]  ? generic_file_write_iter+0x109/0x5e0
[   70.228540][ T9350]  ? vfs_write+0xb0f/0x14e0
[   70.228997][ T9350]  ? ksys_write+0x23e/0x490
[   70.229458][ T9350]  ? __x64_sys_write+0x97/0xf0
[   70.229939][ T9350]  ? x64_sys_call+0x3015/0x3cf0
[   70.230432][ T9350]  ? do_syscall_64+0xd9/0x1d0
[   70.230941][ T9350]  ? entry_SYSCALL_64_after_hwframe+0x77/0x7f
[   70.231926][ T9350]  ? kmsan_get_metadata+0x13e/0x1c0
[   70.232738][ T9350]  ? kmsan_internal_set_shadow_origin+0x77/0x110
[   70.233711][ T9350]  ? kmsan_get_metadata+0x13e/0x1c0
[   70.234516][ T9350]  ? kmsan_get_shadow_origin_ptr+0x4a/0xb0
[   70.235398][ T9350]  ? __msan_metadata_ptr_for_load_4+0x24/0x40
[   70.236323][ T9350]  ? hfsplus_brec_find+0x218/0x9f0
[   70.237090][ T9350]  ? __pfx_hfs_find_rec_by_key+0x10/0x10
[   70.237938][ T9350]  ? __msan_instrument_asm_store+0xbf/0xf0
[   70.238827][ T9350]  ? __msan_metadata_ptr_for_store_4+0x27/0x40
[   70.239772][ T9350]  ? __hfsplus_ext_write_extent+0x536/0x620
[   70.240666][ T9350]  ? kmsan_get_metadata+0x13e/0x1c0
[   70.241175][ T9350]  __msan_warning+0x96/0x120
[   70.241645][ T9350]  __hfsplus_ext_cache_extent+0x7d0/0x990
[   70.242223][ T9350]  hfsplus_file_extend+0x74f/0x1cf0
[   70.242748][ T9350]  hfsplus_get_block+0xe16/0x17b0
[   70.243255][ T9350]  ? kmsan_internal_set_shadow_origin+0x77/0x110
[   70.243878][ T9350]  ? kmsan_get_metadata+0x13e/0x1c0
[   70.244400][ T9350]  ? kmsan_get_shadow_origin_ptr+0x4a/0xb0
[   70.244967][ T9350]  __block_write_begin_int+0x962/0x2ce0
[   70.245531][ T9350]  ? __pfx_hfsplus_get_block+0x10/0x10
[   70.246079][ T9350]  cont_write_begin+0x1000/0x1950
[   70.246598][ T9350]  hfsplus_write_begin+0x85/0x130
[   70.247105][ T9350]  ? __pfx_hfsplus_get_block+0x10/0x10
[   70.247650][ T9350]  ? __pfx_hfsplus_write_begin+0x10/0x10
[   70.248211][ T9350]  generic_perform_write+0x3e8/0x1060
[   70.248752][ T9350]  __generic_file_write_iter+0x215/0x460
[   70.249314][ T9350]  generic_file_write_iter+0x109/0x5e0
[   70.249856][ T9350]  ? kmsan_internal_set_shadow_origin+0x77/0x110
[   70.250487][ T9350]  vfs_write+0xb0f/0x14e0
[   70.250930][ T9350]  ? __pfx_generic_file_write_iter+0x10/0x10
[   70.251530][ T9350]  ksys_write+0x23e/0x490
[   70.251974][ T9350]  __x64_sys_write+0x97/0xf0
[   70.252450][ T9350]  x64_sys_call+0x3015/0x3cf0
[   70.252924][ T9350]  do_syscall_64+0xd9/0x1d0
[   70.253384][ T9350]  ? irqentry_exit+0x16/0x60
[   70.253844][ T9350]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[   70.254430][ T9350] RIP: 0033:0x7f7a92adffc9
[   70.254873][ T9350] Code: 00 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 48
[   70.256674][ T9350] RSP: 002b:00007fff0bca3188 EFLAGS: 00000202 ORIG_RAX: 0000000000000001
[   70.257485][ T9350] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f7a92adffc9
[   70.258246][ T9350] RDX: 000000000208e24b RSI: 0000000020000100 RDI: 0000000000000004
[   70.258998][ T9350] RBP: 00007fff0bca31a0 R08: 00007fff0bca31a0 R09: 00007fff0bca31a0
[   70.259769][ T9350] R10: 0000000000000000 R11: 0000000000000202 R12: 000055e0d75f8250
[   70.260520][ T9350] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
[   70.261286][ T9350]  </TASK>
[   70.262026][ T9350] Kernel Offset: disabled

(gdb) l *__hfsplus_ext_cache_extent+0x7d0
0xffffffff8318aef0 is in __hfsplus_ext_cache_extent (fs/hfsplus/extents.c:168).
163 fd->key->ext.cnid = 0;
164 res = hfs_brec_find(fd, hfs_find_rec_by_key);
165 if (res && res != -ENOENT)
166 return res;
167 if (fd->key->ext.cnid != fd->search_key->ext.cnid ||
168 fd->key->ext.fork_type != fd->search_key->ext.fork_type)
169 return -ENOENT;
170 if (fd->entrylength != sizeof(hfsplus_extent_rec))
171 return -EIO;
172 hfs_bnode_read(fd->bnode, extent, fd->entryoffset,

The __hfsplus_ext_cache_extent() calls __hfsplus_ext_read_extent():

res = __hfsplus_ext_read_extent(fd, hip->cached_extents, inode->i_ino,

				block, HFSPLUS_IS_RSRC(inode) ?
					HFSPLUS_TYPE_RSRC :
					HFSPLUS_TYPE_DATA);

And if inode->i_ino could be equal to zero or any non-available CNID, then hfs_brec_find() could not find the record in the tree. As a result, fd->key could be compared with fd->search_key. But hfsplus_find_init() uses kmalloc() for fd->key and fd->search_key allocation:

int hfs_find_init(struct hfs_btree *tree, struct hfs_find_data *fd) {
<skipped>

        ptr = kmalloc(tree->max_key_len * 2 + 4, GFP_KERNEL);
        if (!ptr)
                return -ENOMEM;
        fd->search_key = ptr;
        fd->key = ptr + tree->max_key_len + 2;

<skipped>
}

Finally, fd->key is still not initialized if hfs_brec_find() has found nothing.

This patch changes kmalloc() on kzalloc() in hfs_find_init() and intializes fd->record, fd->keyoffset, fd->keylength, fd->entryoffset, fd->entrylength for the case if hfs_brec_find() has been found nothing in the b-tree node.

---
 fs/hfsplus/bfind.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
fs/hfsplus/bfind.c +7 -1
index 901e83d65d202..26ebac4c60424 100644
@@ -18,7 +18,7 @@ int hfs_find_init(struct hfs_btree *tree, struct hfs_find_data *fd)
 
 	fd->tree = tree;
 	fd->bnode = NULL;
-	ptr = kmalloc(tree->max_key_len * 2 + 4, GFP_KERNEL);
+	ptr = kzalloc(tree->max_key_len * 2 + 4, GFP_KERNEL);
 	if (!ptr)
 		return -ENOMEM;
 	fd->search_key = ptr;
@@ -158,6 +158,12 @@ int hfs_brec_find(struct hfs_find_data *fd, search_strategy_t do_key_compare)
 	__be32 data;
 	int height, res;
 
+	fd->record = -1;
+	fd->keyoffset = -1;
+	fd->keylength = -1;
+	fd->entryoffset = -1;
+	fd->entrylength = -1;
+
 	tree = fd->tree;
 	if (fd->bnode)
 		hfs_bnode_put(fd->bnode);
Signature · 1 line
2.51.0
author maintainer
#268 lore raw

PATCH 262/332 hfs: validate record offset in hfsplus_bmap_alloc

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Yang Chenzhi <[email protected]>

[ Upstream commit 738d5a51864ed8d7a68600b8c0c63fe6fe5c4f20 ]

hfsplus_bmap_alloc can trigger a crash if a
record offset or length is larger than node_size

[   15.264282] BUG: KASAN: slab-out-of-bounds in hfsplus_bmap_alloc+0x887/0x8b0
[   15.265192] Read of size 8 at addr ffff8881085ca188 by task test/183
[   15.265949]
[   15.266163] CPU: 0 UID: 0 PID: 183 Comm: test Not tainted 6.17.0-rc2-gc17b750b3ad9 #14 PREEMPT(voluntary)
[   15.266165] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[   15.266167] Call Trace:
[   15.266168]  <TASK>
[   15.266169]  dump_stack_lvl+0x53/0x70
[   15.266173]  print_report+0xd0/0x660
[   15.266181]  kasan_report+0xce/0x100
[   15.266185]  hfsplus_bmap_alloc+0x887/0x8b0
[   15.266208]  hfs_btree_inc_height.isra.0+0xd5/0x7c0
[   15.266217]  hfsplus_brec_insert+0x870/0xb00
[   15.266222]  __hfsplus_ext_write_extent+0x428/0x570
[   15.266225]  __hfsplus_ext_cache_extent+0x5e/0x910
[   15.266227]  hfsplus_ext_read_extent+0x1b2/0x200
[   15.266233]  hfsplus_file_extend+0x5a7/0x1000
[   15.266237]  hfsplus_get_block+0x12b/0x8c0
[   15.266238]  __block_write_begin_int+0x36b/0x12c0
[   15.266251]  block_write_begin+0x77/0x110
[   15.266252]  cont_write_begin+0x428/0x720
[   15.266259]  hfsplus_write_begin+0x51/0x100
[   15.266262]  cont_write_begin+0x272/0x720
[   15.266270]  hfsplus_write_begin+0x51/0x100
[   15.266274]  generic_perform_write+0x321/0x750
[   15.266285]  generic_file_write_iter+0xc3/0x310
[   15.266289]  __kernel_write_iter+0x2fd/0x800
[   15.266296]  dump_user_range+0x2ea/0x910
[   15.266301]  elf_core_dump+0x2a94/0x2ed0
[   15.266320]  vfs_coredump+0x1d85/0x45e0
[   15.266349]  get_signal+0x12e3/0x1990
[   15.266357]  arch_do_signal_or_restart+0x89/0x580
[   15.266362]  irqentry_exit_to_user_mode+0xab/0x110
[   15.266364]  asm_exc_page_fault+0x26/0x30
[   15.266366] RIP: 0033:0x41bd35
[   15.266367] Code: bc d1 f3 0f 7f 27 f3 0f 7f 6f 10 f3 0f 7f 77 20 f3 0f 7f 7f 30 49 83 c0 0f 49 29 d0 48 8d 7c 17 31 e9 9f 0b 00 00 66 0f ef c0 <f3> 0f 6f 0e f3 0f 6f 56 10 66 0f 74 c1 66 0f d7 d0 49 83 f8f
[   15.266369] RSP: 002b:00007ffc9e62d078 EFLAGS: 00010283
[   15.266371] RAX: 00007ffc9e62d100 RBX: 0000000000000000 RCX: 0000000000000000
[   15.266372] RDX: 00000000000000e0 RSI: 0000000000000000 RDI: 00007ffc9e62d100
[   15.266373] RBP: 0000400000000040 R08: 00000000000000e0 R09: 0000000000000000
[   15.266374] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
[   15.266375] R13: 0000000000000000 R14: 0000000000000000 R15: 0000400000000000
[   15.266376]  </TASK>

When calling hfsplus_bmap_alloc to allocate a free node, this function first retrieves the bitmap from header node and map node using node->page together with the offset and length from hfs_brec_lenoff

```
len = hfs_brec_lenoff(node, 2, &off16);
off = off16;

off += node->page_offset;
pagep = node->page + (off >> PAGE_SHIFT);
data = kmap_local_page(*pagep);
```

However, if the retrieved offset or length is invalid(i.e. exceeds node_size), the code may end up accessing pages outside the allocated range for this node.

This patch adds proper validation of both offset and length before use, preventing out-of-bounds page access. Move is_bnode_offset_valid and check_and_correct_requested_length to hfsplus_fs.h, as they may be required by other functions.

---
 fs/hfsplus/bnode.c      | 41 ----------------------------------------
 fs/hfsplus/btree.c      |  6 ++++++
 fs/hfsplus/hfsplus_fs.h | 42 +++++++++++++++++++++++++++++++++++++++++
 3 files changed, 48 insertions(+), 41 deletions(-)
fs/hfsplus/bnode.c +0 -41
index c9c38fddf505b..e566cea238279 100644
@@ -18,47 +18,6 @@
 #include "hfsplus_fs.h"
 #include "hfsplus_raw.h"
 
-static inline
-bool is_bnode_offset_valid(struct hfs_bnode *node, int off)
-{
-	bool is_valid = off < node->tree->node_size;
-
-	if (!is_valid) {
-		pr_err("requested invalid offset: "
-		       "NODE: id %u, type %#x, height %u, "
-		       "node_size %u, offset %d\n",
-		       node->this, node->type, node->height,
-		       node->tree->node_size, off);
-	}
-
-	return is_valid;
-}
-
-static inline
-int check_and_correct_requested_length(struct hfs_bnode *node, int off, int len)
-{
-	unsigned int node_size;
-
-	if (!is_bnode_offset_valid(node, off))
-		return 0;
-
-	node_size = node->tree->node_size;
-
-	if ((off + len) > node_size) {
-		int new_len = (int)node_size - off;
-
-		pr_err("requested length has been corrected: "
-		       "NODE: id %u, type %#x, height %u, "
-		       "node_size %u, offset %d, "
-		       "requested_len %d, corrected_len %d\n",
-		       node->this, node->type, node->height,
-		       node->tree->node_size, off, len, new_len);
-
-		return new_len;
-	}
-
-	return len;
-}
 
 /* Copy a specified range of bytes from the raw data of a node */
 void hfs_bnode_read(struct hfs_bnode *node, void *buf, int off, int len)
fs/hfsplus/btree.c +6 -0
index 66774f4cb4fd5..2211907537fec 100644
@@ -392,6 +392,12 @@ struct hfs_bnode *hfs_bmap_alloc(struct hfs_btree *tree)
 	len = hfs_brec_lenoff(node, 2, &off16);
 	off = off16;
 
+	if (!is_bnode_offset_valid(node, off)) {
+		hfs_bnode_put(node);
+		return ERR_PTR(-EIO);
+	}
+	len = check_and_correct_requested_length(node, off, len);
+
 	off += node->page_offset;
 	pagep = node->page + (off >> PAGE_SHIFT);
 	data = kmap(*pagep);
fs/hfsplus/hfsplus_fs.h +42 -0

48 lines not on this page · raw message

Signature · 1 line
2.51.0
author maintainer
#269 lore raw

PATCH 263/332 hfsplus: fix KMSAN uninit-value issue in hfsplus_delete_cat()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Viacheslav Dubeyko <[email protected]>

[ Upstream commit 9b3d15a758910bb98ba8feb4109d99cc67450ee4 ]

The syzbot reported issue in hfsplus_delete_cat():

[   70.682285][ T9333] =====================================================
[   70.682943][ T9333] BUG: KMSAN: uninit-value in hfsplus_subfolders_dec+0x1d7/0x220
[   70.683640][ T9333]  hfsplus_subfolders_dec+0x1d7/0x220
[   70.684141][ T9333]  hfsplus_delete_cat+0x105d/0x12b0
[   70.684621][ T9333]  hfsplus_rmdir+0x13d/0x310
[   70.685048][ T9333]  vfs_rmdir+0x5ba/0x810
[   70.685447][ T9333]  do_rmdir+0x964/0xea0
[   70.685833][ T9333]  __x64_sys_rmdir+0x71/0xb0
[   70.686260][ T9333]  x64_sys_call+0xcd8/0x3cf0
[   70.686695][ T9333]  do_syscall_64+0xd9/0x1d0
[   70.687119][ T9333]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[   70.687646][ T9333]
[   70.687856][ T9333] Uninit was stored to memory at:
[   70.688311][ T9333]  hfsplus_subfolders_inc+0x1c2/0x1d0
[   70.688779][ T9333]  hfsplus_create_cat+0x148e/0x1800
[   70.689231][ T9333]  hfsplus_mknod+0x27f/0x600
[   70.689730][ T9333]  hfsplus_mkdir+0x5a/0x70
[   70.690146][ T9333]  vfs_mkdir+0x483/0x7a0
[   70.690545][ T9333]  do_mkdirat+0x3f2/0xd30
[   70.690944][ T9333]  __x64_sys_mkdir+0x9a/0xf0
[   70.691380][ T9333]  x64_sys_call+0x2f89/0x3cf0
[   70.691816][ T9333]  do_syscall_64+0xd9/0x1d0
[   70.692229][ T9333]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[   70.692773][ T9333]
[   70.692990][ T9333] Uninit was stored to memory at:
[   70.693469][ T9333]  hfsplus_subfolders_inc+0x1c2/0x1d0
[   70.693960][ T9333]  hfsplus_create_cat+0x148e/0x1800
[   70.694438][ T9333]  hfsplus_fill_super+0x21c1/0x2700
[   70.694911][ T9333]  mount_bdev+0x37b/0x530
[   70.695320][ T9333]  hfsplus_mount+0x4d/0x60
[   70.695729][ T9333]  legacy_get_tree+0x113/0x2c0
[   70.696167][ T9333]  vfs_get_tree+0xb3/0x5c0
[   70.696588][ T9333]  do_new_mount+0x73e/0x1630
[   70.697013][ T9333]  path_mount+0x6e3/0x1eb0
[   70.697425][ T9333]  __se_sys_mount+0x733/0x830
[   70.697857][ T9333]  __x64_sys_mount+0xe4/0x150
[   70.698269][ T9333]  x64_sys_call+0x2691/0x3cf0
[   70.698704][ T9333]  do_syscall_64+0xd9/0x1d0
[   70.699117][ T9333]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[   70.699730][ T9333]
[   70.699946][ T9333] Uninit was created at:
[   70.700378][ T9333]  __alloc_pages_noprof+0x714/0xe60
[   70.700843][ T9333]  alloc_pages_mpol_noprof+0x2a2/0x9b0
[   70.701331][ T9333]  alloc_pages_noprof+0xf8/0x1f0
[   70.701774][ T9333]  allocate_slab+0x30e/0x1390
[   70.702194][ T9333]  ___slab_alloc+0x1049/0x33a0
[   70.702635][ T9333]  kmem_cache_alloc_lru_noprof+0x5ce/0xb20
[   70.703153][ T9333]  hfsplus_alloc_inode+0x5a/0xd0
[   70.703598][ T9333]  alloc_inode+0x82/0x490
[   70.703984][ T9333]  iget_locked+0x22e/0x1320
[   70.704428][ T9333]  hfsplus_iget+0x5c/0xba0
[   70.704827][ T9333]  hfsplus_btree_open+0x135/0x1dd0
[   70.705291][ T9333]  hfsplus_fill_super+0x1132/0x2700
[   70.705776][ T9333]  mount_bdev+0x37b/0x530
[   70.706171][ T9333]  hfsplus_mount+0x4d/0x60
[   70.706579][ T9333]  legacy_get_tree+0x113/0x2c0
[   70.707019][ T9333]  vfs_get_tree+0xb3/0x5c0
[   70.707444][ T9333]  do_new_mount+0x73e/0x1630
[   70.707865][ T9333]  path_mount+0x6e3/0x1eb0
[   70.708270][ T9333]  __se_sys_mount+0x733/0x830
[   70.708711][ T9333]  __x64_sys_mount+0xe4/0x150
[   70.709158][ T9333]  x64_sys_call+0x2691/0x3cf0
[   70.709630][ T9333]  do_syscall_64+0xd9/0x1d0
[   70.710053][ T9333]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[   70.710611][ T9333]
[   70.710842][ T9333] CPU: 3 UID: 0 PID: 9333 Comm: repro Not tainted 6.12.0-rc6-dirty #17
[   70.711568][ T9333] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[   70.712490][ T9333] =====================================================
[   70.713085][ T9333] Disabling lock debugging due to kernel taint
[   70.713618][ T9333] Kernel panic - not syncing: kmsan.panic set ...
[   70.714159][ T9333] CPU: 3 UID: 0 PID: 9333 Comm: repro Tainted: G    B              6.12.0-rc6-dirty #17
[   70.715007][ T9333] Tainted: [B]=BAD_PAGE
[   70.715365][ T9333] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[   70.716311][ T9333] Call Trace:
[   70.716621][ T9333]  <TASK>
[   70.716899][ T9333]  dump_stack_lvl+0x1fd/0x2b0
[   70.717350][ T9333]  dump_stack+0x1e/0x30
[   70.717743][ T9333]  panic+0x502/0xca0
[   70.718116][ T9333]  ? kmsan_get_metadata+0x13e/0x1c0
[   70.718611][ T9333]  kmsan_report+0x296/0x2a0
[   70.719038][ T9333]  ? __msan_metadata_ptr_for_load_4+0x24/0x40
[   70.719859][ T9333]  ? __msan_warning+0x96/0x120
[   70.720345][ T9333]  ? hfsplus_subfolders_dec+0x1d7/0x220
[   70.720881][ T9333]  ? hfsplus_delete_cat+0x105d/0x12b0
[   70.721412][ T9333]  ? hfsplus_rmdir+0x13d/0x310
[   70.721880][ T9333]  ? vfs_rmdir+0x5ba/0x810
[   70.722458][ T9333]  ? do_rmdir+0x964/0xea0
[   70.722883][ T9333]  ? __x64_sys_rmdir+0x71/0xb0
[   70.723397][ T9333]  ? x64_sys_call+0xcd8/0x3cf0
[   70.723915][ T9333]  ? do_syscall_64+0xd9/0x1d0
[   70.724454][ T9333]  ? entry_SYSCALL_64_after_hwframe+0x77/0x7f
[   70.725110][ T9333]  ? vprintk_emit+0xd1f/0xe60
[   70.725616][ T9333]  ? vprintk_default+0x3f/0x50
[   70.726175][ T9333]  ? vprintk+0xce/0xd0
[   70.726628][ T9333]  ? _printk+0x17e/0x1b0
[   70.727129][ T9333]  ? __msan_metadata_ptr_for_load_4+0x24/0x40
[   70.727739][ T9333]  ? kmsan_get_metadata+0x13e/0x1c0
[   70.728324][ T9333]  __msan_warning+0x96/0x120
[   70.728854][ T9333]  hfsplus_subfolders_dec+0x1d7/0x220
[   70.729479][ T9333]  hfsplus_delete_cat+0x105d/0x12b0
[   70.729984][ T9333]  ? kmsan_get_shadow_origin_ptr+0x4a/0xb0
[   70.730646][ T9333]  ? __msan_metadata_ptr_for_load_4+0x24/0x40
[   70.731296][ T9333]  ? kmsan_get_metadata+0x13e/0x1c0
[   70.731863][ T9333]  hfsplus_rmdir+0x13d/0x310
[   70.732390][ T9333]  ? __pfx_hfsplus_rmdir+0x10/0x10
[   70.732919][ T9333]  vfs_rmdir+0x5ba/0x810
[   70.733416][ T9333]  ? kmsan_get_shadow_origin_ptr+0x4a/0xb0
[   70.734044][ T9333]  do_rmdir+0x964/0xea0
[   70.734537][ T9333]  __x64_sys_rmdir+0x71/0xb0
[   70.735032][ T9333]  x64_sys_call+0xcd8/0x3cf0
[   70.735579][ T9333]  do_syscall_64+0xd9/0x1d0
[   70.736092][ T9333]  ? irqentry_exit+0x16/0x60
[   70.736637][ T9333]  entry_SYSCALL_64_after_hwframe+0x77/0x7f
[   70.737269][ T9333] RIP: 0033:0x7fa9424eafc9
[   70.737775][ T9333] Code: 00 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 48
[   70.739844][ T9333] RSP: 002b:00007fff099cd8d8 EFLAGS: 00000202 ORIG_RAX: 0000000000000054
[   70.740760][ T9333] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fa9424eafc9
[   70.741642][ T9333] RDX: 006c6f72746e6f63 RSI: 000000000000000a RDI: 0000000020000100
[   70.742543][ T9333] RBP: 00007fff099cd8e0 R08: 00007fff099cd910 R09: 00007fff099cd910
[   70.743376][ T9333] R10: 0000000000000000 R11: 0000000000000202 R12: 0000565430642260
[   70.744247][ T9333] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
[   70.745082][ T9333]  </TASK>

The main reason of the issue that struct hfsplus_inode_info has not been properly initialized for the case of root folder. In the case of root folder, hfsplus_fill_super() calls the hfsplus_iget() that implements only partial initialization of struct hfsplus_inode_info and subfolders field is not initialized by hfsplus_iget() logic.

This patch implements complete initialization of struct hfsplus_inode_info in the hfsplus_iget() logic with the goal to prevent likewise issues for the case of root folder.

---
 fs/hfsplus/super.c | 23 ++++++++++++++++++-----
 1 file changed, 18 insertions(+), 5 deletions(-)
fs/hfsplus/super.c +18 -5
index 7648f64a17a82..65c63c7a00b12 100644
@@ -67,13 +67,26 @@ struct inode *hfsplus_iget(struct super_block *sb, unsigned long ino)
 	if (!(inode->i_state & I_NEW))
 		return inode;
 
-	INIT_LIST_HEAD(&HFSPLUS_I(inode)->open_dir_list);
-	spin_lock_init(&HFSPLUS_I(inode)->open_dir_lock);
-	mutex_init(&HFSPLUS_I(inode)->extents_lock);
-	HFSPLUS_I(inode)->flags = 0;
+	atomic_set(&HFSPLUS_I(inode)->opencnt, 0);
+	HFSPLUS_I(inode)->first_blocks = 0;
+	HFSPLUS_I(inode)->clump_blocks = 0;
+	HFSPLUS_I(inode)->alloc_blocks = 0;
+	HFSPLUS_I(inode)->cached_start = U32_MAX;
+	HFSPLUS_I(inode)->cached_blocks = 0;
+	memset(HFSPLUS_I(inode)->first_extents, 0, sizeof(hfsplus_extent_rec));
+	memset(HFSPLUS_I(inode)->cached_extents, 0, sizeof(hfsplus_extent_rec));
 	HFSPLUS_I(inode)->extent_state = 0;
+	mutex_init(&HFSPLUS_I(inode)->extents_lock);
 	HFSPLUS_I(inode)->rsrc_inode = NULL;
-	atomic_set(&HFSPLUS_I(inode)->opencnt, 0);
+	HFSPLUS_I(inode)->create_date = 0;
+	HFSPLUS_I(inode)->linkid = 0;
+	HFSPLUS_I(inode)->flags = 0;
+	HFSPLUS_I(inode)->fs_blocks = 0;
+	HFSPLUS_I(inode)->userflags = 0;
+	HFSPLUS_I(inode)->subfolders = 0;
+	INIT_LIST_HEAD(&HFSPLUS_I(inode)->open_dir_list);
+	spin_lock_init(&HFSPLUS_I(inode)->open_dir_lock);
+	HFSPLUS_I(inode)->phys_size = 0;
 
 	if (inode->i_ino >= HFSPLUS_FIRSTUSER_CNID ||
 	    inode->i_ino == HFSPLUS_ROOT_CNID) {
Signature · 1 line
2.51.0
author maintainer
#270 lore raw

PATCH 264/332 dlm: check for defined force value in dlm_lockspace_release

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alexander Aring <[email protected]>

[ Upstream commit 6af515c9f3ccec3eb8a262ca86bef2c499d07951 ]

Force values over 3 are undefined, so don't treat them as 3.

---
 fs/dlm/lockspace.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
fs/dlm/lockspace.c +1 -1
index 624617c12250a..db33e521556e3 100644
@@ -783,7 +783,7 @@ static int release_lockspace(struct dlm_ls *ls, int force)
 
 	dlm_device_deregister(ls);
 
-	if (force < 3 && dlm_user_daemon_available())
+	if (force != 3 && dlm_user_daemon_available())
 		do_uevent(ls, 0);
 
 	dlm_recoverd_stop(ls);
Signature · 1 line
2.51.0
author maintainer
#271 lore raw

PATCH 265/332 hfs: fix KMSAN uninit-value issue in hfs_find_set_zero_bits()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Viacheslav Dubeyko <[email protected]>

[ Upstream commit 2048ec5b98dbdfe0b929d2e42dc7a54c389c53dd ]

The syzbot reported issue in hfs_find_set_zero_bits():

=====================================================

BUG: KMSAN: uninit-value in hfs_find_set_zero_bits+0x74d/0xb60 fs/hfs/bitmap.c:45
 hfs_find_set_zero_bits+0x74d/0xb60 fs/hfs/bitmap.c:45
 hfs_vbm_search_free+0x13c/0x5b0 fs/hfs/bitmap.c:151
 hfs_extend_file+0x6a5/0x1b00 fs/hfs/extent.c:408
 hfs_get_block+0x435/0x1150 fs/hfs/extent.c:353
 __block_write_begin_int+0xa76/0x3030 fs/buffer.c:2151
 block_write_begin fs/buffer.c:2262 [inline]
 cont_write_begin+0x10e1/0x1bc0 fs/buffer.c:2601
 hfs_write_begin+0x85/0x130 fs/hfs/inode.c:52
 cont_expand_zero fs/buffer.c:2528 [inline]
 cont_write_begin+0x35a/0x1bc0 fs/buffer.c:2591
 hfs_write_begin+0x85/0x130 fs/hfs/inode.c:52
 hfs_file_truncate+0x1d6/0xe60 fs/hfs/extent.c:494
 hfs_inode_setattr+0x964/0xaa0 fs/hfs/inode.c:654
 notify_change+0x1993/0x1aa0 fs/attr.c:552
 do_truncate+0x28f/0x310 fs/open.c:68
 do_ftruncate+0x698/0x730 fs/open.c:195
 do_sys_ftruncate fs/open.c:210 [inline]
 __do_sys_ftruncate fs/open.c:215 [inline]
 __se_sys_ftruncate fs/open.c:213 [inline]
 __x64_sys_ftruncate+0x11b/0x250 fs/open.c:213
 x64_sys_call+0xfe3/0x3db0 arch/x86/include/generated/asm/syscalls_64.h:78
 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
 do_syscall_64+0xd9/0x210 arch/x86/entry/syscall_64.c:94
 entry_SYSCALL_64_after_hwframe+0x77/0x7f

Uninit was created at:

 slab_post_alloc_hook mm/slub.c:4154 [inline]
 slab_alloc_node mm/slub.c:4197 [inline]
 __kmalloc_cache_noprof+0x7f7/0xed0 mm/slub.c:4354
 kmalloc_noprof include/linux/slab.h:905 [inline]
 hfs_mdb_get+0x1cc8/0x2a90 fs/hfs/mdb.c:175
 hfs_fill_super+0x3d0/0xb80 fs/hfs/super.c:337
 get_tree_bdev_flags+0x6e3/0x920 fs/super.c:1681
 get_tree_bdev+0x38/0x50 fs/super.c:1704
 hfs_get_tree+0x35/0x40 fs/hfs/super.c:388
 vfs_get_tree+0xb0/0x5c0 fs/super.c:1804
 do_new_mount+0x738/0x1610 fs/namespace.c:3902
 path_mount+0x6db/0x1e90 fs/namespace.c:4226
 do_mount fs/namespace.c:4239 [inline]
 __do_sys_mount fs/namespace.c:4450 [inline]
 __se_sys_mount+0x6eb/0x7d0 fs/namespace.c:4427
 __x64_sys_mount+0xe4/0x150 fs/namespace.c:4427
 x64_sys_call+0xfa7/0x3db0 arch/x86/include/generated/asm/syscalls_64.h:166
 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
 do_syscall_64+0xd9/0x210 arch/x86/entry/syscall_64.c:94
 entry_SYSCALL_64_after_hwframe+0x77/0x7f

CPU: 1 UID: 0 PID: 12609 Comm: syz.1.2692 Not tainted 6.16.0-syzkaller #0 PREEMPT(none)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/12/2025
=====================================================

The HFS_SB(sb)->bitmap buffer is allocated in hfs_mdb_get():

HFS_SB(sb)->bitmap = kmalloc(8192, GFP_KERNEL);

Finally, it can trigger the reported issue because kmalloc() doesn't clear the allocated memory. If allocated memory contains only zeros, then everything will work pretty fine.
But if the allocated memory contains the "garbage", then it can affect the bitmap operations and it triggers the reported issue.

This patch simply exchanges the kmalloc() on kzalloc() with the goal to guarantee the correctness of bitmap operations. Because, newly created allocation bitmap should have all available blocks free. Potentially, initialization bitmap's read operation could not fill the whole allocated memory and "garbage" in the not initialized memory will be the reason of volume coruptions and file system driver bugs.

---
 fs/hfs/mdb.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
fs/hfs/mdb.c +1 -1
index cdf0edeeb2781..f8f976afcc740 100644
@@ -172,7 +172,7 @@ int hfs_mdb_get(struct super_block *sb)
 		pr_warn("continuing without an alternate MDB\n");
 	}
 
-	HFS_SB(sb)->bitmap = kmalloc(8192, GFP_KERNEL);
+	HFS_SB(sb)->bitmap = kzalloc(8192, GFP_KERNEL);
 	if (!HFS_SB(sb)->bitmap)
 		goto out;
 
Signature · 1 line
2.51.0
author maintainer
#272 lore raw

PATCH 266/332 hfsplus: return EIO when type of hidden directory mismatch in hfsplus_fill_super()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Yangtao Li <[email protected]>

[ Upstream commit 9282bc905f0949fab8cf86c0f620ca988761254c ]

If Catalog File contains corrupted record for the case of hidden directory's type, regard it as I/O error instead of Invalid argument.

---
 fs/hfsplus/super.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
fs/hfsplus/super.c +1 -1
index 65c63c7a00b12..9f8945042faa8 100644
@@ -538,7 +538,7 @@ static int hfsplus_fill_super(struct super_block *sb, void *data, int silent)
 	if (!hfs_brec_read(&fd, &entry, sizeof(entry))) {
 		hfs_find_exit(&fd);
 		if (entry.type != cpu_to_be16(HFSPLUS_FOLDER)) {
-			err = -EINVAL;
+			err = -EIO;
 			goto out_put_root;
 		}
 		inode = hfsplus_iget(sb, be32_to_cpu(entry.folder.id));
Signature · 1 line
2.51.0
author maintainer
#273 lore raw

PATCH 267/332 m68k: bitops: Fix find_*_bit() signatures

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Geert Uytterhoeven <[email protected]>

[ Upstream commit 6d5674090543b89aac0c177d67e5fb32ddc53804 ]

The function signatures of the m68k-optimized implementations of the find_{first,next}_{,zero_}bit() helpers do not match the generic variants.

Fix this by changing all non-pointer inputs and outputs to "unsigned long", and updating a few local variables.

---
 arch/m68k/include/asm/bitops.h | 25 ++++++++++++++-----------
 1 file changed, 14 insertions(+), 11 deletions(-)
arch/m68k/include/asm/bitops.h +14 -11
index 10133a968c8e1..d2a9aa0485175 100644
@@ -314,12 +314,12 @@ static inline int bfchg_mem_test_and_change_bit(int nr,
 #include <asm-generic/bitops/ffz.h>
 #else
 
-static inline int find_first_zero_bit(const unsigned long *vaddr,
-				      unsigned size)
+static inline unsigned long find_first_zero_bit(const unsigned long *vaddr,
+						unsigned long size)
 {
 	const unsigned long *p = vaddr;
-	int res = 32;
-	unsigned int words;
+	unsigned long res = 32;
+	unsigned long words;
 	unsigned long num;
 
 	if (!size)
@@ -340,8 +340,9 @@ static inline int find_first_zero_bit(const unsigned long *vaddr,
 }
 #define find_first_zero_bit find_first_zero_bit
 
-static inline int find_next_zero_bit(const unsigned long *vaddr, int size,
-				     int offset)
+static inline unsigned long find_next_zero_bit(const unsigned long *vaddr,
+					       unsigned long size,
+					       unsigned long offset)
 {
 	const unsigned long *p = vaddr + (offset >> 5);
 	int bit = offset & 31UL, res;
@@ -370,11 +371,12 @@ static inline int find_next_zero_bit(const unsigned long *vaddr, int size,
 }
 #define find_next_zero_bit find_next_zero_bit
 
-static inline int find_first_bit(const unsigned long *vaddr, unsigned size)
+static inline unsigned long find_first_bit(const unsigned long *vaddr,
+					   unsigned long size)
 {
 	const unsigned long *p = vaddr;
-	int res = 32;
-	unsigned int words;
+	unsigned long res = 32;
+	unsigned long words;
 	unsigned long num;
 
 	if (!size)
@@ -395,8 +397,9 @@ static inline int find_first_bit(const unsigned long *vaddr, unsigned size)
 }
 #define find_first_bit find_first_bit
 
-static inline int find_next_bit(const unsigned long *vaddr, int size,
-				int offset)
+static inline unsigned long find_next_bit(const unsigned long *vaddr,
+					  unsigned long size,
+					  unsigned long offset)
 {
 	const unsigned long *p = vaddr + (offset >> 5);
 	int bit = offset & 31UL, res;
Signature · 1 line
2.51.0
author maintainer
#274 lore raw

PATCH 268/332 net: rtnetlink: add msg kind names

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nikolay Aleksandrov <[email protected]>

[ Upstream commit 12dc5c2cb7b269c5a1c6d02844f40bfce942a7a6 ]

Add rtnl kind names instead of using raw values. We'll need to check for DEL kind later to validate bulk flag support.

Stable-dep-of: bf29555f5bdc ("rtnetlink: Allow deleting FDB entries in user namespace")

---
 include/net/rtnetlink.h | 7 +++++++
 net/core/rtnetlink.c    | 6 +++---
 2 files changed, 10 insertions(+), 3 deletions(-)
include/net/rtnetlink.h +7 -0
index 5c2a73bbfabee..74eff5259b361 100644
@@ -13,6 +13,13 @@ enum rtnl_link_flags {
 	RTNL_FLAG_DOIT_UNLOCKED = 1,
 };
 
+enum rtnl_kinds {
+	RTNL_KIND_NEW,
+	RTNL_KIND_DEL,
+	RTNL_KIND_GET,
+	RTNL_KIND_SET
+};
+
 void rtnl_register(int protocol, int msgtype,
 		   rtnl_doit_func, rtnl_dumpit_func, unsigned int flags);
 int rtnl_register_module(struct module *owner, int protocol, int msgtype,
net/core/rtnetlink.c +3 -3
index bc86034e17eab..c0a3cf3ed8f34 100644
@@ -5513,11 +5513,11 @@ static int rtnetlink_rcv_msg(struct sk_buff *skb, struct nlmsghdr *nlh,
 {
 	struct net *net = sock_net(skb->sk);
 	struct rtnl_link *link;
+	enum rtnl_kinds kind;
 	struct module *owner;
 	int err = -EOPNOTSUPP;
 	rtnl_doit_func doit;
 	unsigned int flags;
-	int kind;
 	int family;
 	int type;
 
@@ -5534,11 +5534,11 @@ static int rtnetlink_rcv_msg(struct sk_buff *skb, struct nlmsghdr *nlh,
 	family = ((struct rtgenmsg *)nlmsg_data(nlh))->rtgen_family;
 	kind = type&3;
 
-	if (kind != 2 && !netlink_net_capable(skb, CAP_NET_ADMIN))
+	if (kind != RTNL_KIND_GET && !netlink_net_capable(skb, CAP_NET_ADMIN))
 		return -EPERM;
 
 	rcu_read_lock();
-	if (kind == 2 && nlh->nlmsg_flags&NLM_F_DUMP) {
+	if (kind == RTNL_KIND_GET && (nlh->nlmsg_flags & NLM_F_DUMP)) {
 		struct sock *rtnl;
 		rtnl_dumpit_func dumpit;
 		u32 min_dump_alloc = 0;
Signature · 1 line
2.51.0
author maintainer
#275 lore raw

PATCH 269/332 net: rtnetlink: add helper to extract msg types kind

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nikolay Aleksandrov <[email protected]>

[ Upstream commit 2e9ea3e30f696fd438319c07836422bb0bbb4608 ]

Add a helper which extracts the msg type's kind using the kind mask (0x3).

Stable-dep-of: bf29555f5bdc ("rtnetlink: Allow deleting FDB entries in user namespace")

---
 include/net/rtnetlink.h | 6 ++++++
 net/core/rtnetlink.c    | 2 +-
 2 files changed, 7 insertions(+), 1 deletion(-)
include/net/rtnetlink.h +6 -0
index 74eff5259b361..02b0636a4523d 100644
@@ -19,6 +19,12 @@ enum rtnl_kinds {
 	RTNL_KIND_GET,
 	RTNL_KIND_SET
 };
+#define RTNL_KIND_MASK 0x3
+
+static inline enum rtnl_kinds rtnl_msgtype_kind(int msgtype)
+{
+	return msgtype & RTNL_KIND_MASK;
+}
 
 void rtnl_register(int protocol, int msgtype,
 		   rtnl_doit_func, rtnl_dumpit_func, unsigned int flags);
net/core/rtnetlink.c +1 -1
index c0a3cf3ed8f34..2cd4990ac8bc3 100644
@@ -5532,7 +5532,7 @@ static int rtnetlink_rcv_msg(struct sk_buff *skb, struct nlmsghdr *nlh,
 		return 0;
 
 	family = ((struct rtgenmsg *)nlmsg_data(nlh))->rtgen_family;
-	kind = type&3;
+	kind = rtnl_msgtype_kind(type);
 
 	if (kind != RTNL_KIND_GET && !netlink_net_capable(skb, CAP_NET_ADMIN))
 		return -EPERM;
Signature · 1 line
2.51.0
author maintainer
#276 lore raw

PATCH 270/332 net: rtnetlink: use BIT for flag values

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nikolay Aleksandrov <[email protected]>

[ Upstream commit 0569e31f1bc2f50613ba4c219f3ecc0d1174d841 ]

Use BIT to define flag values.

Stable-dep-of: bf29555f5bdc ("rtnetlink: Allow deleting FDB entries in user namespace")

---
 include/net/rtnetlink.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/net/rtnetlink.h +1 -1
index 02b0636a4523d..030fc7eef7401 100644
@@ -10,7 +10,7 @@ typedef int (*rtnl_doit_func)(struct sk_buff *, struct nlmsghdr *,
 typedef int (*rtnl_dumpit_func)(struct sk_buff *, struct netlink_callback *);
 
 enum rtnl_link_flags {
-	RTNL_FLAG_DOIT_UNLOCKED = 1,
+	RTNL_FLAG_DOIT_UNLOCKED = BIT(0),
 };
 
 enum rtnl_kinds {
Signature · 1 line
2.51.0
author maintainer
#277 lore raw

PATCH 271/332 net: netlink: add NLM_F_BULK delete request modifier

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nikolay Aleksandrov <[email protected]>

[ Upstream commit 545528d788556c724eeb5400757f828ef27782a8 ]

Add a new delete request modifier called NLM_F_BULK which, when supported, would cause the request to delete multiple objects. The flag is a convenient way to signal that a multiple delete operation is requested which can be gradually added to different delete requests. In order to make sure older kernels will error out if the operation is not supported instead of doing something unintended we have to break a required condition when implementing support for this flag, f.e. for neighbors we will omit the mandatory mac address attribute. Initially it will be used to add flush with filtering support for bridge fdbs, but it also opens the door to add similar support to others.

Stable-dep-of: bf29555f5bdc ("rtnetlink: Allow deleting FDB entries in user namespace")

---
 include/uapi/linux/netlink.h | 1 +
 1 file changed, 1 insertion(+)
include/uapi/linux/netlink.h +1 -0
index 49751d5fee88a..9bcca78ee1f91 100644
@@ -72,6 +72,7 @@ struct nlmsghdr {
 
 /* Modifiers to DELETE request */
 #define NLM_F_NONREC	0x100	/* Do not delete recursively	*/
+#define NLM_F_BULK	0x200	/* Delete multiple objects	*/
 
 /* Flags for ACK message */
 #define NLM_F_CAPPED	0x100	/* request was capped */
Signature · 1 line
2.51.0
author maintainer
#278 lore raw

PATCH 272/332 net: rtnetlink: add bulk delete support flag

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nikolay Aleksandrov <[email protected]>

[ Upstream commit a6cec0bcd34264be8887791594be793b3f12719f ]

Add a new rtnl flag (RTNL_FLAG_BULK_DEL_SUPPORTED) which is used to verify that the delete operation allows bulk object deletion. Also emit a warning if anyone tries to set it for non-delete kind.

Stable-dep-of: bf29555f5bdc ("rtnetlink: Allow deleting FDB entries in user namespace")

---
 include/net/rtnetlink.h | 3 ++-
 net/core/rtnetlink.c    | 8 ++++++++
 2 files changed, 10 insertions(+), 1 deletion(-)
include/net/rtnetlink.h +2 -1
index 030fc7eef7401..e893b1f21913e 100644
@@ -10,7 +10,8 @@ typedef int (*rtnl_doit_func)(struct sk_buff *, struct nlmsghdr *,
 typedef int (*rtnl_dumpit_func)(struct sk_buff *, struct netlink_callback *);
 
 enum rtnl_link_flags {
-	RTNL_FLAG_DOIT_UNLOCKED = BIT(0),
+	RTNL_FLAG_DOIT_UNLOCKED		= BIT(0),
+	RTNL_FLAG_BULK_DEL_SUPPORTED	= BIT(1),
 };
 
 enum rtnl_kinds {
net/core/rtnetlink.c +8 -0
index 2cd4990ac8bc3..d861744940c6f 100644
@@ -214,6 +214,8 @@ static int rtnl_register_internal(struct module *owner,
 	if (dumpit)
 		link->dumpit = dumpit;
 
+	WARN_ON(rtnl_msgtype_kind(msgtype) != RTNL_KIND_DEL &&
+		(flags & RTNL_FLAG_BULK_DEL_SUPPORTED));
 	link->flags |= flags;
 
 	/* publish protocol:msgtype */
@@ -5594,6 +5596,12 @@ static int rtnetlink_rcv_msg(struct sk_buff *skb, struct nlmsghdr *nlh,
 	}
 
 	flags = link->flags;
+	if (kind == RTNL_KIND_DEL && (nlh->nlmsg_flags & NLM_F_BULK) &&
+	    !(flags & RTNL_FLAG_BULK_DEL_SUPPORTED)) {
+		NL_SET_ERR_MSG(extack, "Bulk delete is not supported");
+		goto err_unlock;
+	}
+
 	if (flags & RTNL_FLAG_DOIT_UNLOCKED) {
 		doit = link->doit;
 		rcu_read_unlock();
Signature · 1 line
2.51.0
author maintainer
#279 lore raw

PATCH 273/332 net: add ndo_fdb_del_bulk

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nikolay Aleksandrov <[email protected]>

[ Upstream commit 1306d5362a591493a2d07f685ed2cc480dcda320 ]

Add a new netdev op called ndo_fdb_del_bulk, it will be later used for driver-specific bulk delete implementation dispatched from rtnetlink. The first user will be the bridge, we need it to signal to rtnetlink from the driver that we support bulk delete operation (NLM_F_BULK).

Stable-dep-of: bf29555f5bdc ("rtnetlink: Allow deleting FDB entries in user namespace")

---
 include/linux/netdevice.h | 9 +++++++++
 1 file changed, 9 insertions(+)
include/linux/netdevice.h +9 -0
index 06b37f45b67c9..d3a3e77a18df1 100644
@@ -1200,6 +1200,10 @@ struct netdev_net_notifier {
  *		      struct net_device *dev,
  *		      const unsigned char *addr, u16 vid)
  *	Deletes the FDB entry from dev coresponding to addr.
+ * int (*ndo_fdb_del_bulk)(struct ndmsg *ndm, struct nlattr *tb[],
+ *			   struct net_device *dev,
+ *			   u16 vid,
+ *			   struct netlink_ext_ack *extack);
  * int (*ndo_fdb_dump)(struct sk_buff *skb, struct netlink_callback *cb,
  *		       struct net_device *dev, struct net_device *filter_dev,
  *		       int *idx)
@@ -1452,6 +1456,11 @@ struct net_device_ops {
 					       struct net_device *dev,
 					       const unsigned char *addr,
 					       u16 vid);
+	int			(*ndo_fdb_del_bulk)(struct ndmsg *ndm,
+						    struct nlattr *tb[],
+						    struct net_device *dev,
+						    u16 vid,
+						    struct netlink_ext_ack *extack);
 	int			(*ndo_fdb_dump)(struct sk_buff *skb,
 						struct netlink_callback *cb,
 						struct net_device *dev,
Signature · 1 line
2.51.0
author maintainer
#280 lore raw

PATCH 274/332 net: rtnetlink: add NLM_F_BULK support to rtnl_fdb_del

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Nikolay Aleksandrov <[email protected]>

[ Upstream commit 9e83425993f38bb89e0ea07849ba0039a748e85b ]

When NLM_F_BULK is specified in a fdb del message we need to handle it differently. First since this is a new call we can strictly validate the passed attributes, at first only ifindex and vlan are allowed as these will be the initially supported filter attributes, any other attribute is rejected. The mac address is no longer mandatory, but we use it to error out in older kernels because it cannot be specified with bulk request (the attribute is not allowed) and then we have to dispatch the call to ndo_fdb_del_bulk if the device supports it. The del bulk callback can do further validation of the attributes if necessary.

Stable-dep-of: bf29555f5bdc ("rtnetlink: Allow deleting FDB entries in user namespace")

---
 net/core/rtnetlink.c | 67 +++++++++++++++++++++++++++++++-------------
 1 file changed, 48 insertions(+), 19 deletions(-)
net/core/rtnetlink.c +48 -19
index d861744940c6f..42c97a71174fe 100644
@@ -4134,22 +4134,34 @@ int ndo_dflt_fdb_del(struct ndmsg *ndm,
 }
 EXPORT_SYMBOL(ndo_dflt_fdb_del);
 
+static const struct nla_policy fdb_del_bulk_policy[NDA_MAX + 1] = {
+	[NDA_VLAN]	= { .type = NLA_U16 },
+	[NDA_IFINDEX]	= NLA_POLICY_MIN(NLA_S32, 1),
+};
+
 static int rtnl_fdb_del(struct sk_buff *skb, struct nlmsghdr *nlh,
 			struct netlink_ext_ack *extack)
 {
+	bool del_bulk = !!(nlh->nlmsg_flags & NLM_F_BULK);
 	struct net *net = sock_net(skb->sk);
+	const struct net_device_ops *ops;
 	struct ndmsg *ndm;
 	struct nlattr *tb[NDA_MAX+1];
 	struct net_device *dev;
-	__u8 *addr;
+	__u8 *addr = NULL;
 	int err;
 	u16 vid;
 
 	if (!netlink_capable(skb, CAP_NET_ADMIN))
 		return -EPERM;
 
-	err = nlmsg_parse_deprecated(nlh, sizeof(*ndm), tb, NDA_MAX, NULL,
-				     extack);
+	if (!del_bulk) {
+		err = nlmsg_parse_deprecated(nlh, sizeof(*ndm), tb, NDA_MAX,
+					     NULL, extack);
+	} else {
+		err = nlmsg_parse(nlh, sizeof(*ndm), tb, NDA_MAX,
+				  fdb_del_bulk_policy, extack);
+	}
 	if (err < 0)
 		return err;
 
@@ -4165,9 +4177,12 @@ static int rtnl_fdb_del(struct sk_buff *skb, struct nlmsghdr *nlh,
 		return -ENODEV;
 	}
 
-	if (!tb[NDA_LLADDR] || nla_len(tb[NDA_LLADDR]) != ETH_ALEN) {
-		NL_SET_ERR_MSG(extack, "invalid address");
-		return -EINVAL;
+	if (!del_bulk) {
+		if (!tb[NDA_LLADDR] || nla_len(tb[NDA_LLADDR]) != ETH_ALEN) {
+			NL_SET_ERR_MSG(extack, "invalid address");
+			return -EINVAL;
+		}
+		addr = nla_data(tb[NDA_LLADDR]);
 	}
 
 	if (dev->type != ARPHRD_ETHER) {
@@ -4175,8 +4190,6 @@ static int rtnl_fdb_del(struct sk_buff *skb, struct nlmsghdr *nlh,
 		return -EINVAL;
 	}
 
-	addr = nla_data(tb[NDA_LLADDR]);
-
 	err = fdb_vid_parse(tb[NDA_VLAN], &vid, extack);
 	if (err)
 		return err;
@@ -4187,10 +4200,16 @@ static int rtnl_fdb_del(struct sk_buff *skb, struct nlmsghdr *nlh,
 	if ((!ndm->ndm_flags || ndm->ndm_flags & NTF_MASTER) &&
 	    netif_is_bridge_port(dev)) {
 		struct net_device *br_dev = netdev_master_upper_dev_get(dev);
-		const struct net_device_ops *ops = br_dev->netdev_ops;
 
-		if (ops->ndo_fdb_del)
-			err = ops->ndo_fdb_del(ndm, tb, dev, addr, vid);
+		ops = br_dev->netdev_ops;
+		if (!del_bulk) {
+			if (ops->ndo_fdb_del)
+				err = ops->ndo_fdb_del(ndm, tb, dev, addr, vid);
+		} else {
+			if (ops->ndo_fdb_del_bulk)
+				err = ops->ndo_fdb_del_bulk(ndm, tb, dev, vid,
+							    extack);
+		}
 
 		if (err)
 			goto out;
@@ -4200,15 +4219,24 @@ static int rtnl_fdb_del(struct sk_buff *skb, struct nlmsghdr *nlh,
 
 	/* Embedded bridge, macvlan, and any other device support */
 	if (ndm->ndm_flags & NTF_SELF) {
-		if (dev->netdev_ops->ndo_fdb_del)
-			err = dev->netdev_ops->ndo_fdb_del(ndm, tb, dev, addr,
-							   vid);
-		else
-			err = ndo_dflt_fdb_del(ndm, tb, dev, addr, vid);
+		ops = dev->netdev_ops;
+		if (!del_bulk) {
+			if (ops->ndo_fdb_del)
+				err = ops->ndo_fdb_del(ndm, tb, dev, addr, vid);
+			else
+				err = ndo_dflt_fdb_del(ndm, tb, dev, addr, vid);
+		} else {
+			/* in case err was cleared by NTF_MASTER call */
+			err = -EOPNOTSUPP;
+			if (ops->ndo_fdb_del_bulk)
+				err = ops->ndo_fdb_del_bulk(ndm, tb, dev, vid,
+							    extack);
+		}
 
 		if (!err) {
-			rtnl_fdb_notify(dev, addr, vid, RTM_DELNEIGH,
-					ndm->ndm_state);
+			if (!del_bulk)
+				rtnl_fdb_notify(dev, addr, vid, RTM_DELNEIGH,
+						ndm->ndm_state);
 			ndm->ndm_flags &= ~NTF_SELF;
 		}
 	}
@@ -5730,7 +5758,8 @@ void __init rtnetlink_init(void)
 	rtnl_register(PF_UNSPEC, RTM_DELLINKPROP, rtnl_dellinkprop, NULL, 0);
 
 	rtnl_register(PF_BRIDGE, RTM_NEWNEIGH, rtnl_fdb_add, NULL, 0);
-	rtnl_register(PF_BRIDGE, RTM_DELNEIGH, rtnl_fdb_del, NULL, 0);
+	rtnl_register(PF_BRIDGE, RTM_DELNEIGH, rtnl_fdb_del, NULL,
+		      RTNL_FLAG_BULK_DEL_SUPPORTED);
 	rtnl_register(PF_BRIDGE, RTM_GETNEIGH, rtnl_fdb_get, rtnl_fdb_dump, 0);
 
 	rtnl_register(PF_BRIDGE, RTM_GETLINK, NULL, rtnl_bridge_getlink, 0);
Signature · 1 line
2.51.0
author maintainer
#281 lore raw

PATCH 275/332 rtnetlink: Allow deleting FDB entries in user namespace

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Johannes Wiesböck <[email protected]>

[ Upstream commit bf29555f5bdc017bac22ca66fcb6c9f46ec8788f ]

Creating FDB entries is possible from a non-initial user namespace when having CAP_NET_ADMIN, yet, when deleting FDB entries, processes receive an EPERM because the capability is always checked against the initial user namespace. This restricts the FDB management from unprivileged containers.

Drop the netlink_capable check in rtnl_fdb_del as it was originally dropped in c5c351088ae7 and reintroduced in 1690be63a27b without intention.

This patch was tested using a container on GyroidOS, where it was possible to delete FDB entries from an unprivileged user namespace and private network namespace.

---
 net/core/rtnetlink.c | 3 ---
 1 file changed, 3 deletions(-)
net/core/rtnetlink.c +0 -3
index 42c97a71174fe..0b44c6b1ef999 100644
@@ -4152,9 +4152,6 @@ static int rtnl_fdb_del(struct sk_buff *skb, struct nlmsghdr *nlh,
 	int err;
 	u16 vid;
 
-	if (!netlink_capable(skb, CAP_NET_ADMIN))
-		return -EPERM;
-
 	if (!del_bulk) {
 		err = nlmsg_parse_deprecated(nlh, sizeof(*ndm), tb, NDA_MAX,
 					     NULL, extack);
Signature · 1 line
2.51.0
author maintainer
#282 lore raw

PATCH 276/332 net: enetc: correct the value of ENETC_RXB_TRUESIZE

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Wei Fang <[email protected]>

[ Upstream commit e59bc32df2e989f034623a580e30a2a72af33b3f ]

The ENETC RX ring uses the page halves flipping mechanism, each page is split into two halves for the RX ring to use. And ENETC_RXB_TRUESIZE is defined to 2048 to indicate the size of half a page. However, the page size is configurable, for ARM64 platform, PAGE_SIZE is default to 4K, but it could be configured to 16K or 64K.

When PAGE_SIZE is set to 16K or 64K, ENETC_RXB_TRUESIZE is not correct, and the RX ring will always use the first half of the page. This is not consistent with the description in the relevant kernel doc and commit messages.

This issue is invisible in most cases, but if users want to increase PAGE_SIZE to receive a Jumbo frame with a single buffer for some use cases, it will not work as expected, because the buffer size of each RX BD is fixed to 2048 bytes.

Based on the above two points, we expect to correct ENETC_RXB_TRUESIZE to (PAGE_SIZE >> 1), as described in the comment.

Fixes d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
---
 drivers/net/ethernet/freescale/enetc/enetc.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/freescale/enetc/enetc.h +1 -1
index 725c3d1cbb198..f58cca219a1e7 100644
@@ -28,7 +28,7 @@ struct enetc_tx_swbd {
 };
 
 #define ENETC_RX_MAXFRM_SIZE	ENETC_MAC_MAXFRM_SIZE
-#define ENETC_RXB_TRUESIZE	2048 /* PAGE_SIZE >> 1 */
+#define ENETC_RXB_TRUESIZE	(PAGE_SIZE >> 1)
 #define ENETC_RXB_PAD		NET_SKB_PAD /* add extra space if needed */
 #define ENETC_RXB_DMA_SIZE	\
 	(SKB_WITH_OVERHEAD(ENETC_RXB_TRUESIZE) - ENETC_RXB_PAD)
Signature · 1 line
2.51.0
author maintainer
#283 lore raw

PATCH 277/332 dpaa2-eth: fix the pointer passed to PTR_ALIGN on Tx path

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Ioana Ciornei <[email protected]>

[ Upstream commit 902e81e679d86846a2404630d349709ad9372d0d ]

The blamed commit increased the needed headroom to account for alignment. This means that the size required to always align a Tx buffer was added inside the dpaa2_eth_needed_headroom() function. By doing that, a manual adjustment of the pointer passed to PTR_ALIGN() was no longer correct since the 'buffer_start' variable was already pointing to the start of the skb's memory.

The behavior of the dpaa2-eth driver without this patch was to drop frames on Tx even when the headroom was matching the 128 bytes necessary. Fix this by removing the manual adjust of 'buffer_start' from the PTR_MODE call.

---
 drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c +1 -2
index 0a1a7d94583b4..d27f5a8e59dcd 100644
@@ -994,8 +994,7 @@ static int dpaa2_eth_build_single_fd(struct dpaa2_eth_priv *priv,
 	dma_addr_t addr;
 
 	buffer_start = skb->data - dpaa2_eth_needed_headroom(skb);
-	aligned_start = PTR_ALIGN(buffer_start - DPAA2_ETH_TX_BUF_ALIGN,
-				  DPAA2_ETH_TX_BUF_ALIGN);
+	aligned_start = PTR_ALIGN(buffer_start, DPAA2_ETH_TX_BUF_ALIGN);
 	if (aligned_start >= skb->head)
 		buffer_start = aligned_start;
 	else
Signature · 1 line
2.51.0
author maintainer
#284 lore raw

PATCH 278/332 arm64, mm: avoid always making PTE dirty in pte_mkwrite()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Huang Ying <[email protected]>

[ Upstream commit 143937ca51cc6ae2fccc61a1cb916abb24cd34f5 ]

Current pte_mkwrite_novma() makes PTE dirty unconditionally. This may mark some pages that are never written dirty wrongly. For example, do_swap_page() may map the exclusive pages with writable and clean PTEs if the VMA is writable and the page fault is for read access. However, current pte_mkwrite_novma() implementation always dirties the PTE. This may cause unnecessary disk writing if the pages are never written before being reclaimed.

So, change pte_mkwrite_novma() to clear the PTE_RDONLY bit only if the PTE_DIRTY bit is set to make it possible to make the PTE writable and clean.

The current behavior was introduced in commit 73e86cb03cf2 ("arm64:
Move PTE_RDONLY bit handling out of set_pte_at()"). Before that, pte_mkwrite() only sets the PTE_WRITE bit, while set_pte_at() only clears the PTE_RDONLY bit if both the PTE_WRITE and the PTE_DIRTY bits are set.

To test the performance impact of the patch, on an arm64 server machine, run 16 redis-server processes on socket 1 and 16 memtier_benchmark processes on socket 0 with mostly get transactions (that is, redis-server will mostly read memory only). The memory footprint of redis-server is larger than the available memory, so swap out/in will be triggered. Test results show that the patch can avoid most swapping out because the pages are mostly clean. And the benchmark throughput improves ~23.9% in the test.

Fixes 73e86cb03cf2 ("arm64: Move PTE_RDONLY bit handling out of set_pte_at()")
Cc Will Deacon <[email protected]>
Cc Anshuman Khandual <[email protected]>
Cc Ryan Roberts <[email protected]>
Cc Gavin Shan <[email protected]>
Cc Ard Biesheuvel <[email protected]>
Cc Matthew Wilcox (Oracle) <[email protected]>
Cc Yicong Yang <[email protected]>
---
 arch/arm64/include/asm/pgtable.h | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
arch/arm64/include/asm/pgtable.h +2 -1
index d92b5aed354e9..9bf40864b6e4f 100644
@@ -174,7 +174,8 @@ static inline pmd_t set_pmd_bit(pmd_t pmd, pgprot_t prot)
 static inline pte_t pte_mkwrite(pte_t pte)
 {
 	pte = set_pte_bit(pte, __pgprot(PTE_WRITE));
-	pte = clear_pte_bit(pte, __pgprot(PTE_RDONLY));
+	if (pte_sw_dirty(pte))
+		pte = clear_pte_bit(pte, __pgprot(PTE_RDONLY));
 	return pte;
 }
 
Signature · 1 line
2.51.0
author maintainer
#285 lore raw

PATCH 279/332 sctp: avoid NULL dereference when chunk data buffer is missing

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Alexey Simakov <[email protected]>

[ Upstream commit 441f0647f7673e0e64d4910ef61a5fb8f16bfb82 ]

chunk->skb pointer is dereferenced in the if-block where it's supposed to be NULL only.

chunk->skb can only be NULL if chunk->head_skb is not. Check for frag_list instead and do it just before replacing chunk->skb. We're sure that otherwise chunk->skb is non-NULL because of outer if() condition.

---
 net/sctp/inqueue.c | 13 +++++++------
 1 file changed, 7 insertions(+), 6 deletions(-)
net/sctp/inqueue.c +7 -6
index 7182c5a450fb5..6a434d441dc70 100644
@@ -163,13 +163,14 @@ struct sctp_chunk *sctp_inq_pop(struct sctp_inq *queue)
 				chunk->head_skb = chunk->skb;
 
 			/* skbs with "cover letter" */
-			if (chunk->head_skb && chunk->skb->data_len == chunk->skb->len)
+			if (chunk->head_skb && chunk->skb->data_len == chunk->skb->len) {
+				if (WARN_ON(!skb_shinfo(chunk->skb)->frag_list)) {
+					__SCTP_INC_STATS(dev_net(chunk->skb->dev),
+							 SCTP_MIB_IN_PKT_DISCARDS);
+					sctp_chunk_free(chunk);
+					goto next_chunk;
+				}
 				chunk->skb = skb_shinfo(chunk->skb)->frag_list;
-
-			if (WARN_ON(!chunk->skb)) {
-				__SCTP_INC_STATS(dev_net(chunk->skb->dev), SCTP_MIB_IN_PKT_DISCARDS);
-				sctp_chunk_free(chunk);
-				goto next_chunk;
 			}
 		}
 
Signature · 1 line
2.51.0
author maintainer
#286 lore raw

PATCH 280/332 net: bonding: fix possible peer notify event loss or dup issue

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Tonghao Zhang <[email protected]>

commit 10843e1492e474c02b91314963161731fa92af91 upstream.

If the send_peer_notif counter and the peer event notify are not synchronized. It may cause problems such as the loss or dup of peer notify event.

Before this patch:
- If should_notify_peers is true and the lock for send_peer_notif-- fails, peer event may be sent again in next mii_monitor loop, because should_notify_peers is still true.
- If should_notify_peers is true and the lock for send_peer_notif-- succeeded, but the lock for peer event fails, the peer event will be lost.

This patch locks the RTNL for send_peer_notif, events, and commit simultaneously.

Fixes 07a4ddec3ce9 ("bonding: add an option to specify a delay between peer notifications")
Cc Jay Vosburgh <[email protected]>
Cc Andrew Lunn <[email protected]>
Cc Eric Dumazet <[email protected]>
Cc Jakub Kicinski <[email protected]>
Cc Paolo Abeni <[email protected]>
Cc Hangbin Liu <[email protected]>
Cc Nikolay Aleksandrov <[email protected]>
Cc Vincent Bernat <[email protected]>
---
 drivers/net/bonding/bond_main.c |   40 ++++++++++++++++++----------------------
 1 file changed, 18 insertions(+), 22 deletions(-)
drivers/net/bonding/bond_main.c +18 -22
@@ -2617,7 +2617,7 @@ static void bond_mii_monitor(struct work
 {
 	struct bonding *bond = container_of(work, struct bonding,
 					    mii_work.work);
-	bool should_notify_peers = false;
+	bool should_notify_peers;
 	bool commit;
 	unsigned long delay;
 	struct slave *slave;
@@ -2629,30 +2629,33 @@ static void bond_mii_monitor(struct work
 		goto re_arm;
 
 	rcu_read_lock();
+
 	should_notify_peers = bond_should_notify_peers(bond);
 	commit = !!bond_miimon_inspect(bond);
-	if (bond->send_peer_notif) {
-		rcu_read_unlock();
-		if (rtnl_trylock()) {
-			bond->send_peer_notif--;
-			rtnl_unlock();
-		}
-	} else {
-		rcu_read_unlock();
-	}
 
-	if (commit) {
+	rcu_read_unlock();
+
+	if (commit || bond->send_peer_notif) {
 		/* Race avoidance with bond_close cancel of workqueue */
 		if (!rtnl_trylock()) {
 			delay = 1;
-			should_notify_peers = false;
 			goto re_arm;
 		}
 
-		bond_for_each_slave(bond, slave, iter) {
-			bond_commit_link_state(slave, BOND_SLAVE_NOTIFY_LATER);
+		if (commit) {
+			bond_for_each_slave(bond, slave, iter) {
+				bond_commit_link_state(slave,
+						       BOND_SLAVE_NOTIFY_LATER);
+			}
+			bond_miimon_commit(bond);
+		}
+
+		if (bond->send_peer_notif) {
+			bond->send_peer_notif--;
+			if (should_notify_peers)
+				call_netdevice_notifiers(NETDEV_NOTIFY_PEERS,
+							 bond->dev);
 		}
-		bond_miimon_commit(bond);
 
 		rtnl_unlock();	/* might sleep, hold no other locks */
 	}
@@ -2660,13 +2663,6 @@ static void bond_mii_monitor(struct work
 re_arm:
 	if (bond->params.miimon)
 		queue_delayed_work(bond->wq, &bond->mii_work, delay);
-
-	if (should_notify_peers) {
-		if (!rtnl_trylock())
-			return;
-		call_netdevice_notifiers(NETDEV_NOTIFY_PEERS, bond->dev);
-		rtnl_unlock();
-	}
 }
 
 static int bond_upper_dev_walk(struct net_device *upper,
author maintainer
#287 lore raw

PATCH 281/332 Revert "cpuidle: menu: Avoid discarding useful information"

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Rafael J. Wysocki <[email protected]>

commit 10fad4012234a7dea621ae17c0c9486824f645a0 upstream.

It is reported that commit 85975daeaa4d ("cpuidle: menu: Avoid discarding useful information") led to a performance regression on Intel Jasper Lake systems because it reduced the time spent by CPUs in idle state C7 which is correlated to the maximum frequency the CPUs can get to because of an average running power limit [1].

Before that commit, get_typical_interval() would have returned UINT_MAX whenever it had been unable to make a high-confidence prediction which had led to selecting the deepest available idle state too often and both power and performance had been inadequate as a result of that on some systems. However, this had not been a problem on systems with relatively aggressive average running power limits, like the Jasper Lake systems in question, because on those systems it was compensated by the ability to run CPUs faster.

It was addressed by causing get_typical_interval() to return a number based on the recent idle duration information available to it even if it could not make a high-confidence prediction, but that clearly did not take the possible correlation between idle power and available CPU capacity into account.

For this reason, revert most of the changes made by commit 85975daeaa4d, except for one cosmetic cleanup, and add a comment explaining the rationale for returning UINT_MAX from get_typical_interval() when it is unable to make a high-confidence prediction.

---
 drivers/cpuidle/governors/menu.c |   21 +++++++++------------
 1 file changed, 9 insertions(+), 12 deletions(-)
drivers/cpuidle/governors/menu.c +9 -12
@@ -256,20 +256,17 @@ again:
 	 *
 	 * This can deal with workloads that have long pauses interspersed
 	 * with sporadic activity with a bunch of short pauses.
+	 *
+	 * However, if the number of remaining samples is too small to exclude
+	 * any more outliers, allow the deepest available idle state to be
+	 * selected because there are systems where the time spent by CPUs in
+	 * deep idle states is correlated to the maximum frequency the CPUs
+	 * can get to.  On those systems, shallow idle states should be avoided
+	 * unless there is a clear indication that the given CPU is most likley
+	 * going to be woken up shortly.
 	 */
-	if (divisor * 4 <= INTERVALS * 3) {
-		/*
-		 * If there are sufficiently many data points still under
-		 * consideration after the outliers have been eliminated,
-		 * returning without a prediction would be a mistake because it
-		 * is likely that the next interval will not exceed the current
-		 * maximum, so return the latter in that case.
-		 */
-		if (divisor >= INTERVALS / 2)
-			return max;
-
+	if (divisor * 4 <= INTERVALS * 3)
 		return UINT_MAX;
-	}
 
 	thresh = max - 1;
 	goto again;
author maintainer
#288 lore raw

PATCH 282/332 MIPS: Malta: Fix keyboard resource preventing i8042 driver from registering

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Maciej W. Rozycki <[email protected]>

commit bf5570590a981d0659d0808d2d4bcda21b27a2a5 upstream.

MIPS Malta platform code registers the PCI southbridge legacy port I/O PS/2 keyboard range as a standard resource marked as busy. It prevents the i8042 driver from registering as it fails to claim the resource in a call to i8042_platform_init(). Consequently PS/2 keyboard and mouse devices cannot be used with this platform.

Fix the issue by removing the busy marker from the standard reservation, making the driver register successfully:

serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12

and the resource show up as expected among the legacy devices:

00000000-00ffffff : MSC PCI I/O

    00000000-0000001f : dma1
    00000020-00000021 : pic1
    00000040-0000005f : timer
    00000060-0000006f : keyboard
      00000060-0000006f : i8042
    00000070-00000077 : rtc0
    00000080-0000008f : dma page reg
    000000a0-000000a1 : pic2
    000000c0-000000df : dma2
    [...]

If the i8042 driver has not been configured, then the standard resource will remain there preventing any conflicting dynamic assignment of this PCI port I/O address range.

---
 arch/mips/mti-malta/malta-setup.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/mips/mti-malta/malta-setup.c +1 -1
@@ -47,7 +47,7 @@ static struct resource standard_io_resou
 		.name = "keyboard",
 		.start = 0x60,
 		.end = 0x6f,
-		.flags = IORESOURCE_IO | IORESOURCE_BUSY
+		.flags = IORESOURCE_IO
 	},
 	{
 		.name = "dma page reg",
author maintainer
#289 lore raw

PATCH 283/332 ocfs2: clear extent cache after moving/defragmenting extents

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Deepanshu Kartikey <[email protected]>

commit 78a63493f8e352296dbc7cb7b3f4973105e8679e upstream.

The extent map cache can become stale when extents are moved or defragmented, causing subsequent operations to see outdated extent flags. This triggers a BUG_ON in ocfs2_refcount_cal_cow_clusters().

The problem occurs when:
1. copy_file_range() creates a reflinked extent with OCFS2_EXT_REFCOUNTED
2. ioctl(FITRIM) triggers ocfs2_move_extents()
3. __ocfs2_move_extents_range() reads and caches the extent (flags=0x2)
4. ocfs2_move_extent()/ocfs2_defrag_extent() calls __ocfs2_move_extent() which clears OCFS2_EXT_REFCOUNTED flag on disk (flags=0x0)
5. The extent map cache is not invalidated after the move
6. Later write() operations read stale cached flags (0x2) but disk has updated flags (0x0), causing a mismatch
7. BUG_ON(!(rec->e_flags & OCFS2_EXT_REFCOUNTED)) triggers

Fix by clearing the extent map cache after each extent move/defrag operation in __ocfs2_move_extents_range(). This ensures subsequent operations read fresh extent data from disk.

---
 fs/ocfs2/move_extents.c |    5 +++++
 1 file changed, 5 insertions(+)
fs/ocfs2/move_extents.c +5 -0
@@ -870,6 +870,11 @@ static int __ocfs2_move_extents_range(st
 			mlog_errno(ret);
 			goto out;
 		}
+		/*
+		 * Invalidate extent cache after moving/defragging to prevent
+		 * stale cached data with outdated extent flags.
+		 */
+		ocfs2_extent_map_trunc(inode, cpos);
 
 		context->clusters_moved += alloc_size;
 next:
author maintainer
#290 lore raw

PATCH 284/332 net: usb: rtl8150: Fix frame padding

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Michal Pecio <[email protected]>

commit 75cea9860aa6b2350d90a8d78fed114d27c7eca2 upstream.

TX frames aren't padded and unknown memory is sent into the ether.

Theoretically, it isn't even guaranteed that the extra memory exists and can be sent out, which could cause further problems. In practice, I found that plenty of tailroom exists in the skb itself (in my test with ping at least) and skb_padto() easily succeeds, so use it here.

In the event of -ENOMEM drop the frame like other drivers do.

The use of one more padding byte instead of a USB zero-length packet is retained to avoid regression. I have a dodgy Etron xHCI controller which doesn't seem to support sending ZLPs at all.

---
 drivers/net/usb/rtl8150.c |   11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)
drivers/net/usb/rtl8150.c +9 -2
@@ -685,9 +685,16 @@ static netdev_tx_t rtl8150_start_xmit(st
 	rtl8150_t *dev = netdev_priv(netdev);
 	int count, res;
 
+	/* pad the frame and ensure terminating USB packet, datasheet 9.2.3 */
+	count = max(skb->len, ETH_ZLEN);
+	if (count % 64 == 0)
+		count++;
+	if (skb_padto(skb, count)) {
+		netdev->stats.tx_dropped++;
+		return NETDEV_TX_OK;
+	}
+
 	netif_stop_queue(netdev);
-	count = (skb->len < 60) ? 60 : skb->len;
-	count = (count & 0x3f) ? count : count + 1;
 	dev->tx_skb = skb;
 	usb_fill_bulk_urb(dev->tx_urb, dev->udev, usb_sndbulkpipe(dev->udev, 2),
 		      skb->data, count, write_bulk_callback, dev);
author maintainer
#291 lore raw

PATCH 285/332 net: ravb: Ensure memory write completes before ringing TX doorbell

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Lad Prabhakar <[email protected]>

commit 706136c5723626fcde8dd8f598a4dcd251e24927 upstream.

Add a final dma_wmb() barrier before triggering the transmit request (TCCR_TSRQ) to ensure all descriptor and buffer writes are visible to the DMA engine.

According to the hardware manual, a read-back operation is required before writing to the doorbell register to guarantee completion of previous writes. Instead of performing a dummy read, a dma_wmb() is used to both enforce the same ordering semantics on the CPU side and also to ensure completion of writes.

---
 drivers/net/ethernet/renesas/ravb_main.c |    8 ++++++++
 1 file changed, 8 insertions(+)
drivers/net/ethernet/renesas/ravb_main.c +8 -0
@@ -1605,6 +1605,14 @@ static netdev_tx_t ravb_start_xmit(struc
 	} else {
 		desc->die_dt = DT_FSINGLE;
 	}
+
+	/* Before ringing the doorbell we need to make sure that the latest
+	 * writes have been committed to memory, otherwise it could delay
+	 * things until the doorbell is rang again.
+	 * This is in replacement of the read operation mentioned in the HW
+	 * manuals.
+	 */
+	dma_wmb();
 	ravb_modify(ndev, TCCR, TCCR_TSRQ0 << q, TCCR_TSRQ0 << q);
 
 	priv->cur_tx[q] += num_tx_desc;
author maintainer
#292 lore raw

PATCH 286/332 riscv: Use of_get_cpu_hwid()

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Rob Herring <[email protected]>

[ Upstream commit bd2259ee458e299ec14061da7faddcfb0d54d154 ]

Replace open coded parsing of CPU nodes' 'reg' property with of_get_cpu_hwid().

Stable-dep-of: d2721bb165b3 ("RISC-V: Don't print details of CPUs disabled in DT")

---
 arch/riscv/kernel/cpu.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
arch/riscv/kernel/cpu.c +2 -1
index 6d59e6906fddf..f13b2c9ea912d 100644
@@ -22,7 +22,8 @@ int riscv_of_processor_hartid(struct device_node *node)
 		return -ENODEV;
 	}
 
-	if (of_property_read_u32(node, "reg", &hart)) {
+	hart = of_get_cpu_hwid(node, 0);
+	if (hart == ~0U) {
 		pr_warn("Found CPU without hart ID\n");
 		return -ENODEV;
 	}
Signature · 1 line
2.51.0
author maintainer
#293 lore raw

PATCH 287/332 RISC-V: Correctly print supported extensions

In reply to Greg Kroah-Hartman

5.10-stable review patch. If anyone has any objections, please let me know.

------------------

From: Tsukasa OI <[email protected]>

[ Upstream commit 58004f266918912771ee71f46bfb92bf64ab9108 ]

This commit replaces BITS_PER_LONG with number of alphabet letters.

Current ISA pretty-printing code expects extension 'a' (bit 0) through 'z' (bit 25). Although bit 26 and higher is not currently used (thus never cause an issue in practice), it will be an annoying problem if we start to use those in the future.

This commit disables printing high bits for now.

Stable-dep-of: d2721bb165b3 ("RISC-V: Don't print details of CPUs disabled in DT")

---
 arch/riscv/kernel/cpufeature.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)
arch/riscv/kernel/cpufeature.c +5 -3
index ac202f44a6702..ece126dad3547 100644
@@ -13,6 +13,8 @@
 #include <asm/smp.h>
 #include <asm/switch_to.h>
 
+#define NUM_ALPHA_EXTS ('z' - 'a' + 1)
+
 unsigned long elf_hwcap __read_mostly;
 
 /* Host ISA bitmap */
@@ -63,7 +65,7 @@ void riscv_fill_hwcap(void)
 {
 	struct device_node *node;
 	const char *isa;
-	char print_str[BITS_PER_LONG + 1];
+	char print_str[NUM_ALPHA_EXTS + 1];
 	size_t i, j, isa_len;
 	static unsigned long isa2hwcap[256] = {0};
 
@@ -133,13 +135,13 @@ void riscv_fill_hwcap(void)
 	}
 
 	memset(print_str, 0, sizeof(print_str));
-	for (i = 0, j = 0; i < BITS_PER_LONG; i++)
+	for (i = 0, j = 0; i < NUM_ALPHA_EXTS; i++)
 		if (riscv_isa[0] & BIT_MASK(i))
 			print_str[j++] = (char)('a' + i);
 	pr_info("riscv: ISA extensions %s\n", print_str);
 
 	memset(print_str, 0, sizeof(print_str));
-	for (i = 0, j = 0; i < BITS_PER_LONG; i++)
+	for (i = 0, j = 0; i < NUM_ALPHA_EXTS; i++)
 		if (elf_hwcap & BIT_MASK(i))
 			print_str[j++] = (char)('a' + i);
 	pr_info("riscv: ELF capabilities %s\n", print_str);
Signature · 1 line
2.51.0