Skip to contentSkip to conversation

Bluetooth: btmtk: Trigger reset on firmware download failure

PATCH In review Chris Lu 3 participants 4 messages Dec 9, 2025 – Dec 11, 2025

Subsystems (2)
lore
Share & tools
lore

Chris Lu

author
#0 lore raw

PATCH 1/1 Bluetooth: btmtk: Trigger reset on firmware download failure

Initiate reset flow if MT79xx series BT failed to download firmware when doing setup.
If driver is not able to get event after reset in the first section of btmtk_usb_setup, the protocol is deemed unuable and driver will return to prevent from repeatedly executing resets.

---
 drivers/bluetooth/btmtk.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)
drivers/bluetooth/btmtk.c +9 -2
index a8c520dc09e1..8b1443b9e9cf 100644
@@ -1333,7 +1333,7 @@ int btmtk_usb_setup(struct hci_dev *hdev)
 						btmtk_usb_hci_wmt_sync);
 		if (err < 0) {
 			bt_dev_err(hdev, "Failed to set up firmware (%d)", err);
-			return err;
+			goto reset_fw;
 		}
 
 		/* It's Device EndPoint Reset Option Register */
@@ -1353,7 +1353,7 @@ int btmtk_usb_setup(struct hci_dev *hdev)
 		err = btmtk_usb_hci_wmt_sync(hdev, &wmt_params);
 		if (err < 0) {
 			bt_dev_err(hdev, "Failed to send wmt func ctrl (%d)", err);
-			return err;
+			goto reset_fw;
 		}
 
 		hci_set_msft_opcode(hdev, 0xFD30);
@@ -1444,6 +1444,13 @@ int btmtk_usb_setup(struct hci_dev *hdev)
 	}
 	kfree_skb(skb);
 
+reset_fw:
+	if (btmtk_data->reset_sync) {
+		bt_dev_err(hdev, "Mediatek do firmware reset");
+		btmtk_reset_sync(hdev);
+		return err;
+	}
+
 done:
 	rettime = ktime_get();
 	delta = ktime_sub(rettime, calltime);
Signature · 1 line
2.45.2
#1 lore raw

This is automated email and please do not reply to this email!

Dear submitter,

Thank you for submitting the patches to the linux bluetooth mailing list. This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=1031700

---Test result---

Test Summary:

CheckPatch                    PENDING   0.39 seconds
GitLint                       PENDING   0.42 seconds
SubjectPrefix                 PASS      0.09 seconds
BuildKernel                   PASS      25.46 seconds
CheckAllWarning               PASS      27.76 seconds
CheckSparse                   PASS      31.06 seconds
BuildKernel32                 PASS      24.82 seconds
TestRunnerSetup               PASS      551.53 seconds
TestRunner_l2cap-tester       PASS      24.20 seconds
TestRunner_iso-tester         PASS      88.35 seconds
TestRunner_bnep-tester        PASS      6.15 seconds
TestRunner_mgmt-tester        FAIL      114.62 seconds
TestRunner_rfcomm-tester      PASS      9.50 seconds
TestRunner_sco-tester         FAIL      14.31 seconds
TestRunner_ioctl-tester       PASS      10.33 seconds
TestRunner_mesh-tester        FAIL      11.41 seconds
TestRunner_smp-tester         PASS      8.48 seconds
TestRunner_userchan-tester    PASS      6.58 seconds
IncrementalBuild              PENDING   0.97 seconds

Details
##############################
Test: CheckPatch - PENDING
Desc: Run checkpatch.pl script
Output:

##############################
Test: GitLint - PENDING
Desc: Run gitlint
Output:

##############################
Test: TestRunner_mgmt-tester - FAIL
Desc: Run mgmt-tester with test-runner Output:
Total: 494, Passed: 489 (99.0%), Failed: 1, Not Run: 4

Failed Test Cases
Read Exp Feature - Success Failed 0.102 seconds
##############################
Test: TestRunner_sco-tester - FAIL
Desc: Run sco-tester with test-runner
Output:
WARNING: possible circular locking dependency detected

BUG: sleeping function called from invalid context at net/core/sock.c:3782

Total: 30, Passed: 30 (100.0%), Failed: 0, Not Run: 0
##############################
Test: TestRunner_mesh-tester - FAIL
Desc: Run mesh-tester with test-runner Output:
Total: 10, Passed: 8 (80.0%), Failed: 2, Not Run: 0

Failed Test Cases

Mesh - Send cancel - 1                               Timed out    1.816 seconds
Mesh - Send cancel - 2                               Timed out    1.999 seconds

##############################
Test: IncrementalBuild - PENDING
Desc: Incremental build with the patches in the series Output:

---
Regards,
Linux Bluetooth

#2 lore raw
In reply to Chris Lu

Hi Chris,

Quoted 35 lines · Chris Lu

Initiate reset flow if MT79xx series BT failed to download firmware when doing setup.
If driver is not able to get event after reset in the first section of btmtk_usb_setup, the protocol is deemed unuable and driver will return to prevent from repeatedly executing resets.

---
 drivers/bluetooth/btmtk.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)
drivers/bluetooth/btmtk.c +2 -2
index a8c520dc09e1..8b1443b9e9cf 100644
@@ -1333,7 +1333,7 @@ int btmtk_usb_setup(struct hci_dev *hdev)
                                                btmtk_usb_hci_wmt_sync);
                if (err < 0) {
                        bt_dev_err(hdev, "Failed to set up firmware (%d)", err);
-                       return err;
+                       goto reset_fw;
                }
 
                /* It's Device EndPoint Reset Option Register */
@@ -1353,7 +1353,7 @@ int btmtk_usb_setup(struct hci_dev *hdev)
                err = btmtk_usb_hci_wmt_sync(hdev, &wmt_params);
                if (err < 0) {
                        bt_dev_err(hdev, "Failed to send wmt func ctrl (%d)", err);
-                       return err;
+                       goto reset_fw;
                }
 
                hci_set_msft_opcode(hdev, 0xFD30);

drivers/bluetooth/btmtk.c int btmtk_usb_setup(struct hci_dev *hdev) · line 1449

Quoted 6 lines
drivers/bluetooth/btmtk.c +3 -0
@@ -1444,6 +1444,13 @@ int btmtk_usb_setup(struct hci_dev *hdev)
        }
        kfree_skb(skb);
 
+reset_fw:
+       if (btmtk_data->reset_sync) {
+               bt_dev_err(hdev, "Mediatek do firmware reset");

This message is a bit cryptic to me, why do we need to print that you will be doing a reset?

drivers/bluetooth/btmtk.c int btmtk_usb_setup(struct hci_dev *hdev) · line 1450

Quoted 1 line
drivers/bluetooth/btmtk.c +1 -0
+               btmtk_reset_sync(hdev);

This seems to be doing a hard reset, which I assume you are doing as an attempt to recover by retrying to setup, but if it fails we may go into a loop condition trying to setup so we better limit the number of attempts.

Quoted 9 lines
drivers/bluetooth/btmtk.c +3 -1
+               return err;
+       }
+
 done:
        rettime = ktime_get();
        delta = ktime_sub(rettime, calltime);
--

2.45.2

Signature · 1 line
Luiz Augusto von Dentz
#3 lore raw

Hi Luiz,

Thanks for your review and response.

Quoted 53 lines · Luiz Augusto von Dentz

External email : Please do not click links or open attachments until you have verified the sender or the content.

Hi Chris,

Quoted 44 lines · Chris Lu

Initiate reset flow if MT79xx series BT failed to download firmware when
doing setup.
If driver is not able to get event after reset in the first section of
btmtk_usb_setup, the protocol is deemed unuable and driver will return to
prevent from repeatedly executing resets.

---
 drivers/bluetooth/btmtk.c | 11 +++++++++--

 1 file changed, 9 insertions(+), 2 deletions(-)
drivers/bluetooth/btmtk.c +0 -0
index a8c520dc09e1..8b1443b9e9cf 100644
@@ -1333,7 +1333,7 @@ int btmtk_usb_setup(struct hci_dev *hdev)


btmtk_usb_hci_wmt_sync);
                if (err < 0) {
                        bt_dev_err(hdev, "Failed to set up firmware (%d)", err);
-                       return err;
+                       goto reset_fw;
                }

                /* It's Device EndPoint Reset Option Register */

drivers/bluetooth/btmtk.c +0 -0
@@ -1353,7 +1353,7 @@ int btmtk_usb_setup(struct hci_dev *hdev)
                 err = btmtk_usb_hci_wmt_sync(hdev, &wmt_params);
                 if (err < 0) {

                        bt_dev_err(hdev, "Failed to send wmt func ctrl (%d)", err);
-                       return err;
+                       goto reset_fw;
                }

                hci_set_msft_opcode(hdev, 0xFD30);

drivers/bluetooth/btmtk.c +0 -0
@@ -1444,6 +1444,13 @@ int btmtk_usb_setup(struct hci_dev *hdev)
         }
         kfree_skb(skb);
 
Quoted 6 lines

drivers/bluetooth/btmtk.c int btmtk_usb_setup(struct hci_dev *hdev) · line 1449

Quoted 3 lines
drivers/bluetooth/btmtk.c +3 -0
+reset_fw:
+       if (btmtk_data->reset_sync) {
+               bt_dev_err(hdev, "Mediatek do firmware reset");

This message is a bit cryptic to me, why do we need to print that you will be doing a reset?

Indeed, this log can only be interpreted by Mediatek engineers. I'll update v2 to remove this line.

Quoted 8 lines

drivers/bluetooth/btmtk.c int btmtk_usb_setup(struct hci_dev *hdev) · line 1450

Quoted 2 lines
drivers/bluetooth/btmtk.c +1 -0
+               btmtk_reset_sync(hdev);

This seems to be doing a hard reset, which I assume you are doing as an attempt to recover by retrying to setup, but if it fails we may go into a loop condition trying to setup so we better limit the number of
attempts.

We only perform reset once when firmware download failed or 'wmt ctrl' command failed.

Before downloading the firmware, driver will send pre-init commands to get information such as chip id, after the reset, if those command still can't work normally, it is considered a protocol issue that it can't be further used. We'll not enter the reset flow again to avoid an endless loop.

There is indeed a potential risk. If the pre-init commands are all fine but firmware download continues to have problem, it could cause a loop condition. Retry limit will be addressed in v2.

Quoted 12 lines
Quoted 10 lines
drivers/bluetooth/btmtk.c +3 -0
+               return err;
+       }
+

 done:
        rettime = ktime_get();
        delta = ktime_sub(rettime, calltime);
--
2.45.2

Quoted 2 lines

--
Luiz Augusto von Dentz

Thanks a lot!
Chris Lu