ARM: dts: microchip: sama7d65: flexcom nodes upgrade
[email protected]
maintainercover ARM: dts: microchip: sama7d65: flexcom nodes upgrade
From: Nicolas Ferre <[email protected]>
This series collects some additions and fixes for flexcom nodes on the sama7d65 platform. It enables access to all usart, spi and i2c controllers of this SoC.
Hari Prasath Gujulan Elango (1):
ARM: dts: microchip: sama7d65: fix the ranges property for flx9
Nicolas Ferre (4):
ARM: dts: microchip: sama7d65: fix size-cells property for i2c3
ARM: dts: microchip: sama7d65: add dma properties to usart6
ARM: dts: microchip: sama7d65: add fifo-size to usart
ARM: dts: microchip: sama7d65: add missing flexcom nodes
arch/arm/boot/dts/microchip/sama7d65.dtsi | 283 +++++++++++++++++++++- 1 file changed, 281 insertions(+), 2 deletions(-)
Signature · 1 line
2.43.0
[email protected]
maintainerPATCH 1/5 ARM: dts: microchip: sama7d65: fix the ranges property for flx9
From: Hari Prasath Gujulan Elango <[email protected]>
Update the ranges property for the flexcom9 as per the datasheet and align with the reg property.
---
Note: Hari's email address will bounce. Change to whichever suits you.
arch/arm/boot/dts/microchip/sama7d65.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/microchip/sama7d65.dtsi +1 -1
@@ -676,7 +676,7 @@ i2c8: i2c@600 { flx9: flexcom@e2820000 { compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom"; reg = <0xe2820000 0x200>; - ranges = <0x0 0xe281c000 0x800>; + ranges = <0x0 0xe2820000 0x800>; clocks = <&pmc PMC_TYPE_PERIPHERAL 43>; #address-cells = <1>; #size-cells = <1>;
Signature · 1 line
2.43.0
[email protected]
maintainerPATCH 2/5 ARM: dts: microchip: sama7d65: fix size-cells property for i2c3
In reply to [email protected]From: Nicolas Ferre <[email protected]>
Fix the #size-cells property for i2c3 node and remove the dtbs_check error telling that "#size-cells: 0 was expected" from schema atmel,at91sam-i2c.yaml and i2c-controller.yaml.
--- arch/arm/boot/dts/microchip/sama7d65.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/microchip/sama7d65.dtsi +1 -1
@@ -527,7 +527,7 @@ i2c3: i2c@600 { interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; clocks = <&pmc PMC_TYPE_PERIPHERAL 37>; #address-cells = <1>; - #size-cells = <1>; + #size-cells = <0>; dmas = <&dma0 AT91_XDMAC_DT_PERID(12)>, <&dma0 AT91_XDMAC_DT_PERID(11)>; dma-names = "tx", "rx";
Signature · 1 line
2.43.0
[email protected]
maintainerPATCH 3/5 ARM: dts: microchip: sama7d65: add dma properties to usart6
In reply to [email protected]From: Nicolas Ferre <[email protected]>
Add the dma property and associated dma activation for usart6 as part of flx6 node.
Is useful for usual default console on this product.
--- arch/arm/boot/dts/microchip/sama7d65.dtsi | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm/boot/dts/microchip/sama7d65.dtsi +5 -0
@@ -617,6 +617,11 @@ uart6: serial@200 { interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; clocks = <&pmc PMC_TYPE_PERIPHERAL 40>; clock-names = "usart"; + dmas = <&dma1 AT91_XDMAC_DT_PERID(18)>, + <&dma1 AT91_XDMAC_DT_PERID(17)>; + dma-names = "tx", "rx"; + atmel,use-dma-rx; + atmel,use-dma-tx; atmel,usart-mode = <AT91_USART_MODE_SERIAL>; atmel,fifo-size = <32>; status = "disabled";
Signature · 1 line
2.43.0
[email protected]
maintainerPATCH 4/5 ARM: dts: microchip: sama7d65: add fifo-size to usart
In reply to [email protected]From: Nicolas Ferre <[email protected]>
When missing, add the atmel,fifo-size = <32> property for usart nodes in flexcom.
--- arch/arm/boot/dts/microchip/sama7d65.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/boot/dts/microchip/sama7d65.dtsi +3 -0
@@ -414,6 +414,7 @@ uart0: serial@200 { dma-names = "tx", "rx"; atmel,use-dma-rx; atmel,use-dma-tx; + atmel,fifo-size = <32>; atmel,usart-mode = <AT91_USART_MODE_SERIAL>; status = "disabled"; };
@@ -492,6 +493,7 @@ uart2: serial@200 { dma-names = "tx", "rx"; atmel,use-dma-rx; atmel,use-dma-tx; + atmel,fifo-size = <32>; atmel,usart-mode = <AT91_USART_MODE_SERIAL>; status = "disabled"; };
@@ -517,6 +519,7 @@ uart3: serial@200 { dma-names = "tx", "rx"; atmel,use-dma-rx; atmel,use-dma-tx; + atmel,fifo-size = <32>; atmel,usart-mode = <AT91_USART_MODE_SERIAL>; status = "disabled"; };
Signature · 1 line
2.43.0
[email protected]
maintainerPATCH 5/5 ARM: dts: microchip: sama7d65: add missing flexcom nodes
In reply to [email protected]From: Nicolas Ferre <[email protected]>
Add nodes for usart, spi and i2c when missing to the flexcom nodes.
--- arch/arm/boot/dts/microchip/sama7d65.dtsi | 271 ++++++++++++++++++++++ 1 file changed, 271 insertions(+)
arch/arm/boot/dts/microchip/sama7d65.dtsi +271 -0
@@ -419,6 +419,21 @@ uart0: serial@200 { status = "disabled"; }; + spi0: spi@400 { + compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi"; + reg = <0x400 0x200>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 34>; + clock-names = "spi_clk"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma1 AT91_XDMAC_DT_PERID(6)>, + <&dma1 AT91_XDMAC_DT_PERID(5)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; + i2c0: i2c@600 { compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c"; reg = <0x600 0x200>;
@@ -443,6 +458,22 @@ flx1: flexcom@e1824000 { #size-cells = <1>; status = "disabled"; + uart1: serial@200 { + compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart"; + reg = <0x200 0x200>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 35>; + clock-names = "usart"; + dmas = <&dma0 AT91_XDMAC_DT_PERID(8)>, + <&dma0 AT91_XDMAC_DT_PERID(7)>; + dma-names = "tx", "rx"; + atmel,use-dma-rx; + atmel,use-dma-tx; + atmel,fifo-size = <32>; + atmel,usart-mode = <AT91_USART_MODE_SERIAL>; + status = "disabled"; + }; + spi1: spi@400 { compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi"; reg = <0x400 0x200>;
@@ -497,6 +528,35 @@ uart2: serial@200 { atmel,usart-mode = <AT91_USART_MODE_SERIAL>; status = "disabled"; }; + + spi2: spi@400 { + compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi"; + reg = <0x400 0x200>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 36>; + clock-names = "spi_clk"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma1 AT91_XDMAC_DT_PERID(10)>, + <&dma1 AT91_XDMAC_DT_PERID(9)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; + + i2c2: i2c@600 { + compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c"; + reg = <0x600 0x200>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 36>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma1 AT91_XDMAC_DT_PERID(10)>, + <&dma1 AT91_XDMAC_DT_PERID(9)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; }; flx3: flexcom@e182c000 {
@@ -524,6 +584,21 @@ uart3: serial@200 { status = "disabled"; }; + spi3: spi@400 { + compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi"; + reg = <0x400 0x200>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 37>; + clock-names = "spi_clk"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma0 AT91_XDMAC_DT_PERID(12)>, + <&dma0 AT91_XDMAC_DT_PERID(11)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; + i2c3: i2c@600 { compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c"; reg = <0x600 0x200>;
@@ -579,6 +654,20 @@ spi4: spi@400 { atmel,fifo-size = <32>; status = "disabled"; }; + + i2c4: i2c@600 { + compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c"; + reg = <0x600 0x200>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 38>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma1 AT91_XDMAC_DT_PERID(14)>, + <&dma1 AT91_XDMAC_DT_PERID(13)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; }; flx5: flexcom@e201c000 {
@@ -590,6 +679,37 @@ flx5: flexcom@e201c000 { #size-cells = <1>; status = "disabled"; + uart5: serial@200 { + compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart"; + reg = <0x200 0x200>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 39>; + clock-names = "usart"; + dmas = <&dma0 AT91_XDMAC_DT_PERID(16)>, + <&dma0 AT91_XDMAC_DT_PERID(15)>; + dma-names = "tx", "rx"; + atmel,use-dma-rx; + atmel,use-dma-tx; + atmel,fifo-size = <32>; + atmel,usart-mode = <AT91_USART_MODE_SERIAL>; + status = "disabled"; + }; + + spi5: spi@400 { + compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi"; + reg = <0x400 0x200>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 39>; + clock-names = "spi_clk"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma0 AT91_XDMAC_DT_PERID(16)>, + <&dma0 AT91_XDMAC_DT_PERID(15)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; + i2c5: i2c@600 { compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c"; reg = <0x600 0x200>;
@@ -629,6 +749,35 @@ uart6: serial@200 { atmel,fifo-size = <32>; status = "disabled"; }; + + spi6: spi@400 { + compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi"; + reg = <0x400 0x200>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 40>; + clock-names = "spi_clk"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma1 AT91_XDMAC_DT_PERID(18)>, + <&dma1 AT91_XDMAC_DT_PERID(17)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; + + i2c6: i2c@600 { + compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c"; + reg = <0x600 0x200>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 40>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma1 AT91_XDMAC_DT_PERID(18)>, + <&dma1 AT91_XDMAC_DT_PERID(17)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; }; flx7: flexcom@e2024000 {
@@ -655,6 +804,35 @@ uart7: serial@200 { atmel,usart-mode = <AT91_USART_MODE_SERIAL>; status = "disabled"; }; + + spi7: spi@400 { + compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi"; + reg = <0x400 0x200>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 41>; + clock-names = "spi_clk"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma1 AT91_XDMAC_DT_PERID(20)>, + <&dma1 AT91_XDMAC_DT_PERID(19)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; + + i2c7: i2c@600 { + compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c"; + reg = <0x600 0x200>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 41>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma1 AT91_XDMAC_DT_PERID(20)>, + <&dma1 AT91_XDMAC_DT_PERID(19)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; }; flx8: flexcom@e281c000 {
@@ -666,6 +844,37 @@ flx8: flexcom@e281c000 { #size-cells = <1>; status = "disabled"; + uart8: serial@200 { + compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart"; + reg = <0x200 0x200>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 42>; + clock-names = "usart"; + dmas = <&dma0 AT91_XDMAC_DT_PERID(22)>, + <&dma0 AT91_XDMAC_DT_PERID(21)>; + dma-names = "tx", "rx"; + atmel,use-dma-rx; + atmel,use-dma-tx; + atmel,fifo-size = <32>; + atmel,usart-mode = <AT91_USART_MODE_SERIAL>; + status = "disabled"; + }; + + spi8: spi@400 { + compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi"; + reg = <0x400 0x200>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 42>; + clock-names = "spi_clk"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma0 AT91_XDMAC_DT_PERID(22)>, + <&dma0 AT91_XDMAC_DT_PERID(21)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; + i2c8: i2c@600 { compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c"; reg = <0x600 0x200>;
@@ -690,6 +899,37 @@ flx9: flexcom@e2820000 { #size-cells = <1>; status = "disabled"; + uart9: serial@200 { + compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart"; + reg = <0x200 0x200>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 43>; + clock-names = "usart"; + dmas = <&dma0 AT91_XDMAC_DT_PERID(24)>, + <&dma0 AT91_XDMAC_DT_PERID(23)>; + dma-names = "tx", "rx"; + atmel,use-dma-rx; + atmel,use-dma-tx; + atmel,fifo-size = <32>; + atmel,usart-mode = <AT91_USART_MODE_SERIAL>; + status = "disabled"; + }; + + spi9: spi@400 { + compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi"; + reg = <0x400 0x200>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 43>; + clock-names = "spi_clk"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma0 AT91_XDMAC_DT_PERID(24)>, + <&dma0 AT91_XDMAC_DT_PERID(23)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; + i2c9: i2c@600 { compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c"; reg = <0x600 0x200>;
@@ -714,6 +954,37 @@ flx10: flexcom@e2824000 { #size-cells = <1>; status = "disabled"; + uart10: serial@200 { + compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart"; + reg = <0x200 0x200>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 44>; + clock-names = "usart"; + dmas = <&dma0 AT91_XDMAC_DT_PERID(26)>, + <&dma0 AT91_XDMAC_DT_PERID(25)>; + dma-names = "tx", "rx"; + atmel,use-dma-rx; + atmel,use-dma-tx; + atmel,fifo-size = <32>; + atmel,usart-mode = <AT91_USART_MODE_SERIAL>; + status = "disabled"; + }; + + spi10: spi@400 { + compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi"; + reg = <0x400 0x200>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 44>; + clock-names = "spi_clk"; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dma0 AT91_XDMAC_DT_PERID(26)>, + <&dma0 AT91_XDMAC_DT_PERID(25)>; + dma-names = "tx", "rx"; + atmel,fifo-size = <32>; + status = "disabled"; + }; + i2c10: i2c@600 { compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c"; reg = <0x600 0x200>;
Signature · 1 line
2.43.0
Quoted 5 lines · On 1/2/26 19:01, [email protected] wrote:
Hari Prasath Gujulan Elango (1):
ARM: dts: microchip: sama7d65: fix the ranges property for flx9Nicolas Ferre (4):
ARM: dts: microchip: sama7d65: fix size-cells property for i2c3
Applied to at91-fixes, thanks!
Quoted 3 lines
ARM: dts: microchip: sama7d65: add dma properties to usart6
ARM: dts: microchip: sama7d65: add fifo-size to usart
ARM: dts: microchip: sama7d65: add missing flexcom nodes
Applied to at91-dt, thanks!